Remaining Civil work, Interior and Furnishing Work ofSport Complex at Bandodkar Colony, Ghoghla, Diu

Items :

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in Cement Mortar 1:6 (1- Cement : 6 -fine sand) (B) Conventional All Floor (below/above Plinth)

Half brick masonry in common brunt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:3 ( 1-Cement : 3-coarse sand ) with 2 Nos of 6mm Mild steel round bars after every three course embedded in Cement Mortar (B) Conventional All Floor

Providing and laying controlled cement cu.m concrete M.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in (C) Slabs,landing,shelves,Balconies, Lintels, Beams, Girders and Cantilever upto floor two level. (more than 10 ton)

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick walls for interior plastering upto floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) All Floor

Providing and fixing 14mm to 16mm thick gang saw cut machine cut for floors, kitchen platforms, vanity counters window sills, facias and similar locatioN.S (M.R) of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing and to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shade. Area of slab over 0.50 sqm

Extra for flaming or leather finising of the 14mm to 16mm thick gang saw cut granite.

Providing edge double moulding to 15mm to 16mm thick granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc.complete as per design approved by Engineer-in-Charge.Granite work

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-inCharge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.(Entrance parking area)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 600X1200 Mat Vitrified Tiles Flooring

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 600X600 Mat Vitrified Tiles Flooring

Providing & fixing Armstrong Athleta Pebble Grey Flooring in Table Tennis,Carrom & chess and gymnasium area(Series BGR-8501)(Thk. 4.5mm)

Providing & fixing Armstrong Athleta Jade Blue Flooring in Badmintone Court Area(Series BG-301) (Thk. 4.5mm)

Providing & fixing Armstrong Athleta Ash Flooring in Yoga Room & Badmintone Cour Wooden Seating Area (Series BG-6812)(Thk. 4.5mm)

Providing & fixing Armstrong Athleta Jade Green Flooring in Badmintone Court area(Series BG-402) (Thk. 4.5mm)

Providing & fixing Amorim Sports Floor Flooring in gymnasium (heavy Wait Equ.) area (Thk. 7.5mm)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum moisture resistant board.

Providing and fixing suspended false ceiling-Knauf Danoline - Strato panel random dia perforated G 8/15/20 : Regular round perforation, which includes providing and fixing GI perimeter channels of size 0.55 mm. Thk. having one flange of 20 mm and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, screw fixed to brick wall/ partition with help of nylon sleeves and screws, at 610 mm centers. The suspended GI intermediate channels of size 45 mm,0.9mm thk with two flanges of 15 mm each from the soffit at 900 mm centers with ceiling angle of width 25mm x 10mm x 0.55mm thk fixed to soffit with GI cleat and steel expansion fasteners. Ceiling section of 0.55 mm thk fixed to the intermediate channels with help of connecting clips and in direction perpendicular to the intermediate channel with centers of 333 mm perforated gypboard is then screw fixed to ceiling section with 25 mm dry wall screws at 300 mm centers. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally the boards are to be joined and finished so as to have a flush look with uniflott jointing compound. The rate shall be for complete item inclusive of all material, labour, wastages , necessary tools & tackles, adhesives consumable hardware & accessories, light fixture cutout, GI & MS Frame work, fabrication, all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. Work complete as per manufacture specification, drawing approval and instructions of the Architect/Client.

Providing & fixing of Woodworks Grille with dowel made of Natural Bamboo with 24mm Prelude 43 Black Exposed Grid. The Woodworks (WW) Grille panel of nominal size 57x300x2400mm comprising 6 blades of 57x16x2376mm with on center spacing of 50mm fixed thru dowel of dia-12mm x 300mm with on center spacing of 300mm and additional end dowels at 150mm from both the edges. Ledger of 6.5x24x2400mm to be used for covering face of wall angle. WW Grille should comply with ASTM-E84: Class A and have Relative Humidity of RH70. The panels are UV coated to Natural or Carbonized shades. Optional : Open edges may be covered using “Edge Caps” of 66x19x2400mm and “Blade Junction” of 66x38x2400mm to be used along the connection of two WW Grille Panels. The grid should be of “” make Prelude 43 with 24mm wide T - section flanges Black powder coating having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 43mm for the main runner & the Cross Tees and with a load carrying capacity of 20 Kgs/M2. Black dowel clips of spring steel to be used for fixing panel to suspension system. INSTALLATION: To comprise main runner spaced at 1200mm centers securely fixed to the structural soffit using suspension system (specifications below) at 1200mm maximum center. The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm center to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 19x19x3000mm, secured to walls at 450 mm maximum centers. Dowel clips are used to fix the panel to suspension with a grid formation of 600mm along the slat and 2 pieces along each dowel for every individual panel. SUSPENSION SYSTEM: accessories supplied by World Industries consisting of M6 Anchor Fasteners with hanger hole, pre Straightened Hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa, along with Adjustable hook clips of 0.8mm thick, galvanized spring steel for 2.5 mm wire with a minimum pull strength of 110 kg. The adjustable clip also consists of a 4 mm aquiline wire to be used with the main runner.

Providing & fixing Armstrong Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy grade 6063. The baffle blade shall be in size of 100x50x3600mm in powder coated to Woodgrain finish – Red Oak & Cherry. The baffle blade shall be suspended using Slotted U-profile of 20 x 30mm at on-center spacing 100mm. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fInstallation of U-Grid: The U profile to be suspended at every 1200mm on-centre using 6mm threaded rod from the structural soffit using U-profile hanger. U-profile splice to be used to join more than one U profiles of length 3.75M. 1st U-Grid Channel must be no more than 400mm from the perimeter.ixed with End caps. Installation of Armstrong Baffles: Locate the slot for Baffle Hangers in U Profile section at 1200mm centres. Hangers are inserted into the slot, and then inserted in the provision in the Al baffle. Two baffle hangers are required one on each side of the U-profile to hold the Al baffle in its place. Each Hanger to be secured into position by inserting the Locking Clip. When doing continuous installation, Baffles blades are to be connected at ends with Baffle Joiner, which are inserted into the top and bottom slots of the Baffle closed profile for alignment only. The bottom Joiner to be located first and fastened on one side only. The top Joiner to be fitted then and secured with grub screws on one side. Then the two Baffle sections shall be joined and the top Joiner is screw fastened on the 2nd Baffle profile. End Caps to be located by pushing the End Cap tongues into open Baffle slots. Installation to be carried out by Armstrong Trained Installation team & Installation should be carried out as per Armstrong recommended procedure.

Providing and Fixing of Soft Fibre Acoustical Suspended Ceiling System at all heights as per drawings including scafolding with Board edge tiles 600 x 600 x 15mm with 24mm exposed grid. The tiles should have Humidity Resistance (RH) of 95%, NRC 0.9, Light Reflectance 85%, Colour White/Black, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 and 7) suitable for Green Building application with recycled content of 66% GW and 74% RW%. Tile laid on 24 mm wide T - section flanges of colour black/white having rotary stitching on all T sections i.e. Main Runner, 1200 mm and 600 mm Cross T with a web hgt of 32mm and a load carrying capacity of 15.34Kgs/M2. The T Sections have a Galvanizing of 90 grams per M2

Providing and Fixing Channeled Woodworks perforated panels of width 192mm, thickness of 15mm and length 2400 mm or as required by the Architect/ approving engineer, made of a Moisture Resistant fibre board with minimum 595 Kg/M3 density substrate with a laminated facing as per the approved shade & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a “Helmholtz” fluted perforation of 3mm width and 13mm of visible panel each. The edges of the panels shall be “tongue‐and grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non‐woven acoustical fleece having NRC of 0.50. The panels shall be mounted on special aluminium splines (keel) using clips provided by and approved by the Architect/ Engineer‐in‐Charge. INSTALLATION: Install wooden battens (provided by others) of section 50x50mm or as approved by the Architect on the solid wall horizontally using screws and plugs at spacing of 600mm centre‐to‐centre. Screw the aluminium extruded keel for channelled woodworks provided by over the lowest and second wooden batten at an on‐entre distance of 600mm. Install the Skirting (provided by others) of width 50mm or more as required by the Architect/ Engineer‐in‐Charge and insert the tongue end of the panel in the skirting. Place the inside clip on the groove end of the panel along the Al keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing inside clips into the next keel till the actual height is achieved. Finish off the edges using wooden moulding of matching colour (provided by others). Installation to be carried out by Trained Installation team & Installation should be carried out as per recommended procedure.

Providing and fixing of factory manufactured laminated doors 35mm thick including 1mm laminate on both sides. The rates also includes wooden lipping of 35mm x 5mm on all sides of the doors. The rates also incudes 1mm laminate on both sides i/c grooving pattern if any as per the drawing complete in all respect and the entire satisfaction of engineer in charge

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and makingnecessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge.

Providing and fixing 12 mm thick frameless toughened glass of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and makingnecessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Dismantling door & window and clerestory windows (steel or wood) colored glass etc.complate and stacking within 50 meter lead or area 3 sq.mt and above.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm). The Frame work shall be paid separately.

Providing Greenlam Sturdo Classiq ue ,Evergree n toilet cubicle (of following standard dimension which includes 600mm door size width) made of heat, bacteria, water, chemical, scratch, impact and anti bacterial resistant l2mm thick solid compact laminate should be suede finish, which includes doors, pilasters & intermediate panels finished with approved texture/shade as detail drawings & as per lS 2046 (lhdian Standard)and as per fhe retardant 85-476/97 nandard.The product should have Green Guard Certificate. This also includes providing and fixing in position necessary hardware made out of stainless steetSrade 316 Finish as per manuf acture's specifications & Architects instructions like (1) SS Adjustable les. (2l SS Gravity HinSes, {3) SS Thumb turn locksei with Occup.ncy indicators, (4) SS coat hooks & SS Doorstopper-304 Grade (5) SS U-Channels, (6) SS Adjustable fooVpedestal, (7) SS Top Rail, l8) Rubber noise deafehing tape, (9) SS screws - 304 Grade & wall Plugs. {10) SS Corner conenctor The top fitting should consist of SS round orsquare shaped top rail which will get fixed as per manufacturer's specifications. Allscrews willof 3O4 Grade in natntess steel with satin finish. All pilasters are supported by Sraintess stee Botiom Ctadding. The base ofthe stainless steel bottom cladding will be anchored to the floor with a clearance height upto 150mm. As perdkection of Engineerin-charge. a)Toilet cubicle with standard dimension of Lshape 2025 mm heishtX lOOOmm Width X 1500mm Depth, which ihcludes 600mm door sidewidth Shades - 149 SUEDE

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth etc.complete.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.(DSR 15.56)

Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior plastering upto floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1‐ cement :4‐sand)

Providing & applying Texture Paint including base preparation and 2 coats of ultima as per manufacturer's specification and Complete in all respects and the entire satisfaction of engineer-in-charge.

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required Texture and Shade as per approved Architectural Elevation after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials etc complete

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour -Two coats

Providing and fixing of glass roofing over stair case cutouts with glass of suitable thickness including making arrangement for glass fixing with MS structure and making the structure completely water proof, to the entire satisfaction of Engineer-in- Charge.

Veneer finished Wooden partition : Providing & fixing 12 mm thick fire retardant marine plywood as per IS 710:2010 and IS 5509:2000 fixed on frame work on both side finished with 4 mm thick veneer. The frame work shall be made from square hollow aluminium section of approved make conforming to IS specification of size 38 x 38 x 1.6 mm vertically and horizontally. The framework shall be fixed as per drawing vertically @ 600 mm c/c & horizontally 1200 mm c/c and first horizontal member shall be fixed at gr. level. In partion frame work (intermediate, perimeter ) & (at vertical or horizontal joint of ply & at turning point ) shall be fixed to the wall/floor & ceiling with Sheet metal screws/Nylon grip screws of Corro-shield /Fischer and shall be supported by filling required size wedges /washers/ MS wall connectors or packings of teak wood /MS washers to ensure right angles and plumb level. All ply/wooden frameworks shall be treated with anti-termite treatment & hidden The framework shall be covered with approved make plywood (as per IS 710:2010 and IS 5509:2000),adhesive ,tape, headless nails etc ,finished with veneer in pattern as shown in the drawing having 10 mm groove at skirting level with veneer finished skirting . Rate shall be inclusive of grooves etc complete as per drawing or as directed by EIC/ Architect. Measurements for partition work to be recorded upto finished false ceiling level only irrespective of aluminium frame work, which shall be provided from gr. level to RCC slab / beams soffit level. Plywood board both side above false ceiling will fixed up to RCC slab and all junction will fill with approved sealant complete. Rates shall also be inclusive of cost of making cut outs/ openings for electrical fixtures, tube lights /air-conditioners ,grills, diffusers etc & providing additional sections for strengthening around the openings/cutouts additional Aluminium support for fixing of patch fittings for doors, making grooves, sections, in filled with termite treated wooden members wherever required or as per drawing /instruction of EIC. and no extra payment shall be considered for additional sections provided. All curved surfaces, recesses, waffles shall be part of the partition including openable shutter wherever required area and finished with the same material. Rate shall be inclusive of all item, whcih are part of partition.work including cutting and finishing of existing false ceiling above partition.

Providing and fixing Wooden Step Seating including MS Frame made out of 50 x 50 mm MS tube. The MS frame will be covered with a layer of 19mm ply followed up by a layer of 8mm thick parquet flooring made out of second class teak wood complete in all respects to the entire satisfaction of Engineer-in- Charge,

Providing & applying polyurthene polish including rubbing, laquer filling, base preparation, Polyurthene polishing and finishing as per manufacturer's recommendation and complete in all respect to the entire satisfaction of the engineer incharge.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Providing and applying plaster of paris putty of 12 mm thickness over plastered surface to prepare the surface even and smooth complete Analysis based on DSR Rates: 13.26

Providing and fixing Roller blinds 100% Blackout , construction 3 ply PVC and1 ply Glass fibre fabric thickness 0.36 mm and weight +-520 GSM, Fire resistance NFPA 701, AATCC 16-2003 4.5 and Green guard certified with Anti fungal and Anti bacterial fabric The control unit is made of high strength reinforced plastic with a clutch of wrap spring design and high carbon steel spring design provided to transmit motion from driving to driven members of clutch The control unit and idler should be mounted on powder coated aluminium Headrail with M.S bracket to keep the fabric in Tension and straight (As per approved sample to the entire satisfaction of Engineer-in-Charge)

Providing and fixing curtains in double gathering made out of premium fabric including inner lining. The rate also includes curtain rod including clamps complete in all respects to the entire satisfaction of Engineer-in-Charge.

Providing and fixing pelmets of upto 150mm/200 mm x 150 to 300 mm L shape made of 19 mm thick ply as per drawing. Rate to be inclusive of lipping, cutting, wastages, necessary fixtures, nails, adhesives, necessary scaffolding, fixing at all heights and for all floors as per drawing and approved sample etc should also take load of all the all roller blinds.

150L Water Cooler: The SDLX 15150 model is a 150 liter water cooler which has a cooling capacity of 150 liter and storage capacity of 150 liter. It has two faucets. Both of them give cold water. The dimensions of the water cooler are 33 inch width, 28 inch depth and 49 inch height.

WATER PURIFIER: RO+UF+TDS Controller..High Capacity.Commercial. - KENT ELITE-II RO - 50 LPH or similar. Make: PureIt/KENT/Eureka Forbes.

Providing & Fixing 3M Controltac opaque printable vinyl with advance repositionability and Comply adhesive for bubble free application as per design approved by E.I.C

Providing and Fixing exterior Led Logo made out of expanded PVC and fixed over MS frame work as per design. The LOGO will be lit up from within with the inbuilt LEDs inside the LOGO. Also, the LOGO should be water resistant, complete in all respects and to the entire satisfaction of Engineer-in-Charge.

Providing & Installing Pictogrames & Signages made out of rowmarksheet for locating various areas as per design and to the complete satisfaction of Engineer-in-Charge.

Providing and fixing 12mm thick HDF board of make GREEN, or CENTURY, or Merino including router cutting in required pattern and as per green building by-laws (as per drawing jali ) with PU( polyutherane) Finish and fixed to ply board base with C.P brass srews and washers etc all complete. as per direction of Engineer-in-charge.

Providing and laying water proofing treatment by chemical injection grout process in basement raft, water tank (Under ground and Over head) or other areas using 20 mm dia MS nozzles of minimum 25mm deep in walls placed and fixed @1.2m distance in both direction in the wall and @ 0.75m c/c along construction joints, consisting of injecting cement slurries of different viscositites under pressure by pump using acrylic based water proofing chemical mixed with neat cement slurry and sealing off nozzles after the injection operation with suitable admixture including providing and applying two coats of acrylic based water proofing chemical mixed with neat cement slurry coating as per manufacturers specifications and providing 12-15mm thick neat finished cement plaster 1:3 (1 cement : 3 coarse sand) added with acrylic based water proofing chemical as per manufacturers specification and direction of Project Manager. For Vertical and Horizontal Surfaces.

Providing and laying water proofing treatment by using bituminous felt 4" wide over the joints of Puff roofing i/c applying primer adhesive coat for sticking bituminous felt as per specifications

Providing, fabricating and fixing of Reception table of following sizes made of BWR grade plywood of 19mm thick conforming to IS 303 to achieve 50mm thick and exposed surfaces shall be finished with 12mm thick Corean of approved colour, shade and make , including two nos. storage units of size 450mmx600mmx600mm with three equal drawers made of 19mm thick ply finished with 3.5-4mm thick polished veneer of approved colour, shade and make , including necessary hardware like SS handles , sliding channels, locks , including providing and fixing grommet of approved make, all the surfaces below table shall be finished with 1mm thick laminate of approved colour , make and shade , including necessary arrangements for electrical cables, boxes etc. including all material and labour all complete as per drawings, specifications and direction of Engineer-In-Charge. 3000mm x 750mm x 1050mm H

PRODUCT : Connect Cabin Table with Side Table and Mobile Pedestal Size : Main Table 1800 L X 750 W x 750 H mm Size : Side Table 1200 L X 450 W x 750 H mm SYSTEM : CONNECT, Specification : Table top : 25mm thick Pre-laminate particle board with 2mm pvc edge banding on all expossed edges. Under-structure : Supported on MS powdercoated CONNECT leg with supporting beams. Modesty Panel : 18mm thick prelam particle board Modesty panel considered on main side of front table. Wire management : 65Dia grommet. Side / Back Storage : Storages are made of 25mm Thk Table Top, 18mm Thk Openable Shutters with finger groove handle. Mobile Pedestal -PRELAM PEDESTAL 2D+ 1F SIZE : 400L X 450D X 600HT DESCRIPTION : TABLE TOP : Made of 18mm thick Pre-laminated particle board finished with 2mm PVC edge lipping. Back - 9 mm thick pre laminate particle board Edge - All exposed area with 2mm thick PVC EDGE Lipping. Handle - New finger groove handle.

Back Storage : SIZE - 2700 L X 450 D X 750HT mm PRODUCT - STORAGE Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: New finger groove handle Lock: Regular lock

Linear Workstation 1400x700 For Workstations Main Table & Mobile Pedestal PRODUCT : LINEARWORKSTATION Size: 1400LX700DX1100HT SYSTEM : CONNECT Specification : Table top : 25mm thick Pre-laminate particle board E1 norms finished with 2mm pvc edge banding on all expossed edges. Screen : 18mm thick fabric magnetic screen on studs (1250LX350HT) Under-structure : Supported on MS powdercoated CONNECT leg with supporting beams. Wire management : 65mm Dia grommet and Below Table Top 250 mm HT laminate fascia Raceway & separator for power & data cable management. MS vertical cover for wire entry.

PRELAM PEDESTAL 2D+ 1F SIZE : 400L X 450D X 600HT DESCRIPTION : TOP : Made of 18mm thick Pre-laminated particle board finished with 2mm PVC edge lipping. Back - 9 mm thick pre laminate particle board Edge - All exposed area with 2mm thick PVC EDGE Lipping. Handle - New finger groove handle.

P/F of Pearl Leatherette - 2 SEATER SOFA in Leatherette upholster with chrome finish frame and legs

SINGLE SEATER SOFA Model : Peral Single Seater Fabric

CENTER TABLE - 900 X 600 X 450HT

CENTER ROUND TABLE- 450 DIA X 450HT

Center Table 2500x750x750 ht.

Providing & supplying High Back Chair. Model - ANATOM HBGS ADJ ARMS WITH HEADREST * Anatom Medium Back Mesh Chair * With Headrest * AC 60 Mesh * Fabric Upholstered Cushion Seat * Single Lock Synchro Mechanism * Adjustable Lumbar Support * One Way Adjustable Arms (Height) * Nylon Base

Providing & supplying mid Back Chair. Model : ANATOM MBGS ADJ ARMS * Anatom Medium Back Mesh Chair * AC 60 Mesh * Fabric Upholstered Cushion Seat * Single Lock Synchro Mechanism * Adjustable Lumbar Support * One Way Adjustable Arms (Height) * Nylon Base

Vegan Lounger (without Headrest) along with cushion complete

Bedford Side Table with 8mm Toughened glass 450 x 450 x 450 mm

10Feet dia Single layer Centrepole and bumbershoot Umbrella with Sauleda Fabric

90 Kg umbrella base

Cross Trainer

Upright Bike

Recumbent Bike

Treadmill

Spin Bike

Weighing Scale

Leg curl

Dumbell Rack

Simple Bench

Seated Rowing

Abs Crunch Bench

Gym Balls

Yoga Mats

Biceps Curl

Chest Fly

Thigh Abductor

Leg Press Free

Leg Extension

Let Pull Down

Cable Cross Over

Flat Bench press

Providing & fixing of carrom board table of size 900 x 900 mm and 750mm high , top made of water proof ply of suitable thickness and legas to be made up of MS hollow square section of 20mm including four numbers of chairs to match with the table specifications, MS part of tables and chairs to be duly painted complete in all respects to the entire satisfaction of the Engineer-in Charge.

Providing & fixing of carom board as per approved make & sample by Architect. Work complete including all type of material,hardware, loading,unloading,transporation, accessories etc complete as per detailed drawings, specifications & instruction, size and approved from of Architect/EIC. ( Including GST )

Table- size : 750 mm(L) x 750mm (W): Table Top : Top should be made of 25 mm th. MDF with veneer finish & PU polish as per approved shadesEdge finish : All side PVC edge Imported banding of Rehau or approved make Base Frame : The understructure ( Horizontal & Vertical support) should be made of Stainless Steel / Mild Steel 40/50 mm square pipe of 1.6 mm thickness of 16g fitted on four Legs / central pole. All the SS components should be properly buffed & all MS components is Duly powder Coated. Fasteners & Bush : Nylon / PP Bushes, Alen key bolts, T. Nuts drilled in the raw MDF & riverted for perfect strength witch is Taken from Reputed Manufacturer.. Rate shall be inclusive of all materials, loading, unloading, transportation, placing at all floors and for all leads, polishing and all accessories, SS brackets ,sample mockup etc as described in item description.work complete as per the instruction of Client/EIC.

Providing & fixing of chess board as per approved make & sample by Architect. Work complete including all type of material,hardware, loading,unloading,transporation, accessories etc complete as per detailed drawings, specifications & instruction size and approved of Architect/EIC.

Providing & fixing of Table tennis table foldable type, TTFI APPROVED 25 MM thick pre-laminated particle board. Both sides laminated. Includes 100 MM wheels with locking device and levelers. Includes in Package - TT Table, TT Net, Net Clamps, and a User Manual. Top Size: 2740 x 1525 x 760 MM Base Frame Material: Made of 38 x 38 MM Square Steel Tube complete in all respects

Providing & fixing of dart board as per approved make & sample by Architect. Work complete including all type of material,hardware, loading,unloading,transporation, accessories etc complete as per detailed drawings, specifications & instruction, size and approvred of Architect/EIC.

Providing & fixing of Heavy Duty Badminton post in aluminium and steel uprights option with built in weights & floor protection pad fitted with base, uprights and back support can be detached, including wheels for easy movement complet in all respects.

Providing & fixing of Badminton Net 20 feet x 2.5 feet size, with tape all round.

Providing & placing chair as per refrence image /approved by architect Padding material shall be high resiliency polyurethane foam, The back shall be 3/4” thick. The seat shall be 1-1/2” thick.Seating fabric shall be approved by architect All upholstery shall be first quality without creases, stretch lines, or wrinkles. The frame shall be teaksolid wood. All wood shall be finished with semigloss pu finish The work shall be done as per the approved shop drawing (to be prepared by contractor), specifications, sample approved and as directed by the Architect/EIC. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles, sample, loading, unloading, transportation, placing at all floors and all accessories etc. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this.

Supplying of Dumbbells made up of rubber having weight of 15 kilogram and hexagonal in shape and having folowing dimensions - Length: 28.5 cm Height: 15.5 cm Handle diameter: 3.4 cm with a minimum warranty of 2 Years or more.

Supplying of Dumbbells made up of rubber having weight of 05 kilogram and hexagonal in shape and having folowing dimensions - Length: 22.5 cm Height: 12 cm Handle diameter: 3.4 cm with a minimum warranty of 2 Years or more.

Supplying of Dumbbells made up of rubber having weight of 10 kilogram and hexagonal in shape and having folowing dimensions - Length: 26.5 cm Height: 14 cm Handle diameter: 3.4 cm with a minimum warranty of 2 Years or more.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. 1200x600mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. 600 x 600mm

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel board having IP-64 protection made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary supporting angles, flats including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of engineer-in-charge with erection, supplied switch gears, BUSBARS, with suitable size of inter connecting PVC copper wire / copper-aluminium strips, rubber grommets, rib, bakelite control fuses for measuring instruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket complete. The Panel shall be painted with epoxy powder coating. (The rates includes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following approved manufacturers as per attached SLD - MAIN LT Panel (as per attached Single Line diagram)

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) - Three phase 8 way SS Double door for horizontal single phase outgoing

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) - (H) Single phase 12 way SS Double door

Miniature circuit breaker single pole 6A to 32A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark - SP MCB

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 6 to 32 Amp. - DP MCB

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 40Amp. - DP MCB

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 6 to 32 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 40 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 63 Amp.

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 25 Amps.DP

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 40 Amps.DP

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 63 Amps.DP

Sheets steel powder coated enclosure suitable for incorporating One/Two nos. MCB. - Double Pole / Four Pole

Surge Protection Devices (SPD) Supplying, Assembling, levelling, connecting & testing following VSPs etc in boards as specified in 8.1, 8.2 & 8.3 1.4KV Protection level FP ,Class 'I', (Imax-40KA, 8/20µS) LEGRAND Cat no. 3938 or Equivalent

1.2KV Protection level FP, Class 's', (Imax-15KA, 8/20µS) LEGRAND Cat no.3943 or Equivalent

1.2KV Protection level DP, Class 's', (Imax-15KA, 8/20µS) LEGRAND Cat no. 3941 or Equivalent

Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. at 415 V. having normal current rating up to 125A. with Fixed thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only with Sheet metal Enclosure

Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. at 415 V. having normal current rating up to 250A. with Fixed thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only with Sheet metal Enclosure

Providing and erecting metallic vitrified danger notice board for MEDIUM VOLTAGE installation to be erected as per IS.

Providing and erecting metallic vitrified danger notice board for HIGH VOLTAGE installation to be erected as per IS.

Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display. Also comprised permanent ON/OFF switching. Programming switches & housed in fire proof thermoplastic enclosure & transparent cover erected as required with necessary connection erected as directed.

Providing and erecting approved make light control unit suitable to operate on 230V +20% having ON/OFF delay time of 30-50 seconds and having facility for Auto/manual system having two LDR lens to intensity light having capacity of 5A complete erected on section pillar with pipe and stand. Supplying & erecting power contactor for time switch complete erected as per direction Cat III 4 pole 440V 40 Amp.

Making trench in soft soil of suitable width of 90 cms deep for laying cable or locating the fault all over the run and backfilling the same and making the surface as normal ground.

Covering of cable with second class bricks or cement tiles laid cover the cable crosswise & also on both sides with covering of 7. 5 Cms. layer of sand above & below cable (16 bricks per meter)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.(a) 4 core 2.5 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.(a-1) 4 core 4 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.(B) 4 core 6 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables(c) 4 core 10 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables(d) 4 core 16 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables(C) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (G) 3 1/2 core 185 Sq. mm ( 95 Sq. mm 1/2 core)

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Copper lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (b) 4 core 4 Sq. mm / (a) 4 core 2.5 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Copper lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (C) 4 core 6 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (E) 4 core 10 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (A) 3 & 1/2 core 25 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (C) 3 & 1/2 core 70 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (G) 3 & 1/2 core 185 Sq. mm

Supplying & laying under floor pregalvanised corrosion proof rectangular sheet steel cable trunking of 1.6 mm thick having with stand point load up to 1.33 Ton & free from seepage of concrete of screed water having following size of dimensions and No of compartments (W x D x T) : 150mm x 38mm x 1.6mm with Three Compartments

[C] G.I. Junction cross over box for metal / Al. trunking with duct entry 25mm x 38mm size having epoxy powder coated trap lead with corrosion & rust free having load bearing capacity of 3.6 TONS with adjustable levelling screw of following size.150mm x 150mm x 60/75 mm depth

[C] G.I. Junction cross over box for metal / Al. trunking with duct entry 25mm x 38mm size having epoxy powder coated trap lead with corrosion & rust free having load bearing capacity of 3.6 TONS with adjustable levelling screw of following size.300mm x 300mm x 60/75 mm depth

Supplying and erecting approved make GRP Perforated type Cable Tray Material – Corrosion Resistant Polyester Flame Retardant U.V. Stabilized Resin System - Manufactured from Pultruded Sections- Polyester Resin System, Glass Content : 55 – 60 % - - Standard Length : 3000mm- Support Span – 1500mm, Deflection L/200 - Specification NEMA FG1 1993- UV Resistant - Flame Retardant – IS 6746 - Appendix K/UL 94, Very Low Flammability - Specification Followed NEMA FG1 1993 Oxygen Index – Minimum 30% as per ASTM D 2863 - Flame Spread (Extent of Burning) – 20mm as per Standard ASTM D 635 - Tensile Strength – 4000 – 8000 Kg/Cm2 as per Standard ASTM D 638 - Flexural Strength – 2500 – 10000 Kg/Cm2 as per Standard ASTM D 790- Izod Impact Strength – 130 Kg/Cm2 as per Standard ASTM D 256- Compressive Strength – 2500 – 5000 Kg/Cm2 as per Standard ASTM D 695- Barcol Hardness – 50 – 65 (D) Width - 150mm, Pultruded “C” Channel with 30mm Sides 3mm Thickness, Loading 15 Kg./Mtr.

(E) Width - 200mm, Pultruded “C” Channel with 40mm Sides 4mm Thickness, Loading 25 Kg./Mtr.

(F) Width - 300mm, Pultruded “C” Channel with 50mm Sides 4mm Thickness, Loading 30 Kg./Mtr.

Fabrication : Supplying , fabricating and installation of various sizes clamps for cable tray supports using available M.S. sections & rod as per drawings or instructions of engineer in charge or consultant including applying zinc chromate yellow oxide and two to three coats of required enamel paints with anchor fasteners etc.

HEAT / FIRE RESISTANT COATING OF CABLE Supply and application of intumescent based coating on cables/ cable tray using CP 678 firestop cable coating of HILTI make or equivalent. The coating shall have a density in the range of 1.2 to 1.4 Kg/ L. The coating shall be non-toxic, asbestos and halogen free and shall have good mechanical strength. The coating shall comply with IEC 332 part 3 (1992).

Point wiring for Light Point / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed.with medium class Rigid PVC pipe and accessories

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in (a) with medium class Rigid PVC pipe and accessories Wire : (a) 2 wire 1.5 sq. mm

Additional Wire : Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in (a) with medium class Rigid PVC pipe and accessories Wire : (b) 2 wire 2.5 sq. mm

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling, complete with earth continuity and necessary connection with primary light with accessories erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of .ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling ,complete with 6A Modular type switches and following type of accessories erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary batten/angle holder or ceiling rose or H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling complete with 6A Modular type switch and hum free EME four or more step type electronic fan regulator with separately mounted and accessories with earth continuity of following type erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories

Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type accessories

Do - As - Above but for 6 A x 5 pin 250 Volt switched socket outlet point at convenient location. ( Plug & Switch can be together or at different location )

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [II] For 6/16A Plug with 2-2.5 sq.mm Cu. Wire (a) with medium class Rigid PVC pipe and accessories

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [III] For 16A Plug with 2-4 sq.mm Cu. Wire (a) with medium class Rigid PVC pipe and accessories

Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or Open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm thickness

Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or Open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 32 mm rigid PVC pipe of 1.6-1.8 mm thickness

Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or Open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 40 mm rigid PVC pipe of 1.6-1.8 mm thickness

Providing & laying ISI marked Rigid PVC pipe having 6Kg / cm2 (Class-3) to be erected at road crossing on or floor as directed for laying of cable. The pipes as following size of dia & weight per 6 mtr. (B) 50 mm Dia. (2.5Kg/6RMT)

Providing & laying ISI marked Rigid PVC pipe having 6Kg / cm2 (Class-3) to be erected at road crossing on or floor as directed for laying of cable. The pipes as following size of dia & weight per 6 mtr. (D) 75 mm Dia (5.5 Kg / 6RMT)

Providing & laying ISI marked Rigid PVC pipe having 6Kg / cm2 (Class-3) to be erected at road crossing on or floor as directed for laying of cable. The pipes as following size of dia & weight per 6 mtr. (E) 90 mm Dia (8.0 Kg / 6RMT)

Supplying & erecting Electronic Type Cordless Call Bell erected on PVC/Metal board having portable bell push working on D.C. & bell on 230V A.C. supply with cells / battery

Computer : Power Plugs 1 no. universal plug-switch combined + 1 Nos swithc for Below table 2 nos. 6A 5 pin Plug as below Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type accessories Cat. III + Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [I] For 6A Plug with 2-1.5 sq.mm Cu. Wire (Car.iii) + [II] For 16A Plug with 2-2.5 sq.mm Cu. Wire (Car.iii)

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with following sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size : 4 wire 4 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with following sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size : 4 wire 6 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size : 4 wire 10 sq. mm

Providing & erecting Approved make Ceiling Fan with double ball bearing ISI mark with Condenser 230 volt A.C.50 Hz 1200 mm sweep complete having 3 blades aluminium body and blade sets having ornamental design shanks , canopy & 30 cms. down rod erected with 24/0.2, 3 core flexible wire with earthing. It should be BLDC motor -5, 320RPM, 30-35W 5-Star rating Power saving Fan

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete with necessary 24/ O.20, 3 core flexible wire with earthing.

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM [C] 380 mm dia 1400 RPM

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM [D] 450 mm dia 900 RPM

Supply,installation, testing and commisioning of Internal light fixtures of 1200mm long LED Tube light (20W) with 110LPW white color Aluminum extruded body and milky white diffuser.Make : Trilux, Wipro, Philips

Supply,installation, testing and commisioning of Internal light fixtures of 600mm long LED Tube light (14W) with 110LPW white color Aluminum extruded body and milky white diffuser.Make : Trilux, Wipro, Philips

Supply,installation, testing and commisioning of IP-65 Surface Mounted 10W LED down light with White Aluminum dia cast, powder coated housing, reflector, PMMA Deep Down LG7 Diffuser cover with LED lamp with inbuilt driver and driver. LUMEN EFFICACY >110lm/w, PF >0.90, THD <20%, CCT 6000K, Make : Trilux, Wipro, Philips

Supply,installation, testing and commisioning of IP-65 Surface Mounted 16W LED down light with White Aluminum dia cast, powder coated housing, reflector, PMMA Deep Down LG7 Diffuser cover with LED lamp with inbuilt driver and driver. LUMEN EFFICACY >110lm/w, PF >0.90, THD <20%, CCT 6000K, Make : Trilux, Wipro, Philips

Supply,installation, testing and commisioning of IP-20 Recessed Mounted 10W LED down light with White Aluminum dia cast, powder coated housing, reflector, PMMA Deep Down LG7 Diffuser cover with LED lamp with inbuilt driver and driver. LUMEN EFFICACY >110lm/w, PF >0.90, THD <20%, CCT 6000K, Make : Trilux, Wipro, Philips

Supply,installation, testing and commisioning of IP-65 Recessed Mounted 18W LED down light with White Aluminum dia cast, powder coated housing, reflector, PMMA Deep Down LG7 Diffuser cover with LED lamp with inbuilt driver and driver. LUMEN EFFICACY >110lm/w, PF >0.90, THD <20%, CCT 6000K, Make : Trilux, Wipro, Philips

Supply,installation, testing and commisioning of Wall Mounted IP-65 2x6W LED up-down light with die cast construction, Double reflector, toughened glass cover with LED lamp and driver.-PF>0.9 ,THD <20% ,Make : Trilux, Wipro, Philips

Supply,installation, testing and commisioning of IP-65 -IK 07 ,10-12W LED Bollard light with die cast aluminum die cast powder coated housing, reflector,with LED lamp and driver.Make : Trilux, Wipro, Philips

Supply,installation, testing and commisioning of IP-65 3-6W LED foot light with die cast aluminum 150-200 mm long Recessed / surfaced, IP-65 powder coated housing, reflector, toughened glass cover with LED lamp and driver. Make : Trilux, Wipro, Philips

Supply,installation, testing and commisioning of IP-65 3-6W LED Spike light with die cast aluminum 300 mm long spike, powder coated housing, reflector, toughened glass cover with LED lamp and driver. Make : Trilux, Wipro, Philips

Supply,installation, testing and commisioning of Recccesed light fixtures suitable for Tech Zone ceiling size of 150wide x 2400mm long LED Tube light (28W) with Micro Prismatic Diffuser,4kv SPD Matt Steel Grey Extruded Aluminum Body with system luman output minimum 2800 lm. Make : Trilux, Wipro, Philips

Supply,installation, testing and commisioning of IP-68 6-10W LED Swimming Pool light with die cast aluminum 50-150 mm dia Recessed, IP-68 powder coated housing with external Driver if require, toughened glass cover with LED lamp and driver. Make : Trilux, Wipro, Philips

Supply,installation, testing and commisioning of LED Strip light 10-12W . Mtr with external Driver if require, driver. Make : Trilux, Wipro, Philips

Supply,installation, testing and commisioning of IP-65 35-40W LED Each LED Lmap Post made up of die cast aluminum, powder coated IP-65 housing, reflector, toughened glass cover with LED lamp and driversuitable for mounting on 3.0 Mtr FRP Light Pole. Make : Trilux, Wipro, Philips, K-Lite

Supply of approved make GRP / FRP Pole having following specifications: GRP Light Pole made by CNC filament winding machine using thermoset resin polyester/epoxy resin system) having minimum 62% glass content. The pole should be in one piece and tapered round in shape, having smooth finish and should be totally free from corrosion as well as non conductive & shock proof Pole should be provided with FRP Anchor Base and it should be heavy duty, or MS Material duly painted with Epoxy paint. Pole should be flame retardant as per IS 6746. Resin used shall be UV resistance and pigmented. A highly weather resistant polyurethane coating shall be applied to the pole after applying suitable primer system that ensures proper adhesion of the paint. Minimum coating thickness shall be 80 to 100 micron. Deflection of the pole shall not exceed more than 10% of the length of pole for the given load“? Pole should be generally made as per the dimensional data, performance criteria and some interchangeability features of poles as per standard ANSI C 136.20 latest version or ASTM D 4923/01 . The size of pole and type of installation are as below . [B] Overall length of 3 Mtr Average Thickness: 7mm. Top/ Bottom OD Dia A/F 89/130mm ± 2mm approx. Weight of Pole: 12 kg apporx. (Without Base) Anchor Base (Size 250X250 & 12mm th.)

Providing M-20 / 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for the pole of size 45 x 45 x 100 cms. Deep in below ground level with plinth of 45 cms x 45 cms (or 45 cms dia x 45 cms) high upper ground level with necessary curing and finishing in approved manner. ( for 4 & 6 mtr pole)

Supplying & erecting approved make SMC press moulded composite FRP. loop-in, loop-out approx. 2mm thick box complete with bakelite connector strip 4way & hinged doors having locking arrangements with mounting clamp with nuts, bolts & washers suitable for erection on pole with cable clamps& earth bolt of following size of box.: (b) 250mm x 200mm x 100mm [deep]

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications. (c) For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA) i.e independent Earthing in normal soil. Length of Pipe : 3.00 mtrs Back filling Compound :2 nos Bags of 25 Kg.

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications. (b)For Electrical installation up to 11 KV in normal soil. Length of Pipe : 2.00 mtrs Back filling Compound :1 no. Bag of 25 Kg.

Supplying & erecting of Conventional Lightening arrestor with Test loop and Counter as per IS standard

Providing and erecting required size Copper strip for earthing of H.T. OCB / ACB/ Transformer, LT panel board, Motors etc. using copper clamp.

Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG.

Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or Open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm thickness .

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. (8) Modem Jack for Computer Open RJ-45 - cat-III

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. (3) Two Pin/RJ-11 Telephone Socket for One Gong Bell - cat-iii

Supplying & erecting Push button type telephone instrument (A)BEETEL Secure / BPL/, SONY / PANASONIC or equivalent make

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction : [C] CAT - 6

Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of pairs. With necessary connections. (b) Armoured [Jelly Filled] - 10 Pair

Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or Open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm thickness .

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. RG-6 Cable

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. RG-11 Cable

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. for (4) TV Co-axial Socket outlet

Supply, Installation, Testing and Commissioning of 5 Megapixel HD Dome Camera, HD1080p,1/2.7" CMOS, 24 pcs LEDs, 20m IR, Indoor IR Eyeball, ICR, 0.1 Lux/F1.2, 12 VDC, Smart IR, DNR, DWDR, 3.6mm lens, 4 IN 1

Supply, Installation, Testing & Commissioning of 2 Megapixel HD Dome Camera, HD1080p,1/2.7" CMOS, 24 pcs LEDs, 20m IR, Outdoor IR Bullet, ICR, 0.1 Lux/F1.2, 12 VDC, Smart IR, DNR, DWDR, IP66, 3.6mm lens, 4 IN 1 OUTPUT

Supply, Installation, Testing and Commissioning of 16-Channel Digital Video Recorder recording with 4TB HDD with all require installation and integration with all camera system, 16 Turbo HD input, 16-ch video&1-ch audio input, 2 SATA interface, 1280×720P: 25(P)/30(N) fps/ch, 380 1U caseW/O HDD with all require software

Installation, Testing and Commissioning of 32" Full HD LED monitor with Power Cord complete as required & necessary video cards complete as required (if required). Make - Sony, Samsung, Philips

Supply, Installation, Testing and Commissioning Power Supply for Camera

Supply, Installation, Testing and Commissioning CCTV cable in 25mm dia PVC Pipe 3+1 Camera Cable

Supply installation testing and commissioning High Speed quick power charging station for Electrical vehicle as per standard voltage rating with 40A FP MCB and 2 Nos 6A power plugs, it should have digital screen and all parameter recorders.

Supply installation testing and commissioning of roof top solar system with 20 years performance warranty , cost include high efficiency solar SPV module, require earthing, Lightening arrestor, supporting fabrication hot dip GI structure with paint, all require wiring, ACDB DCDB, Solar power meter, and inverter as require with consideration of 1-Year DLP (1KW Each)

AMC : Comprehensive AMC with performance gurantee for the Installed Solar Panel for 1st Year after DLP (period 3% of Inititla Cost) Cleaning of panels, Preventive maitnancne, Checking of all wire connection, Inverter, Monthly Report to AMC etc

AMC : Comprehensive AMC with [erformance gurantee for the Installed Solar Panel for 2nd Year after DLP (period 3.5% of Inititla Cost) Cleaning of panels, Preventive maitnancne, Checking of all wire connection, Inverter, Monthly Report to AMC etc

AMC : Comprehensive AMC with [erformance gurantee for the Installed Solar Panel for 3rd Year after DLP (period 4% of Inititla Cost) Cleaning of panels, Preventive maitnancne, Checking of all wire connection, Inverter, Monthly Report to AMC etc

Supplyinhg certified, trained 2+Year Experienced / Electrician man-power for the Monthly Basis for 1st Year Scope of work to Operate & maintnance of the following Work Lt Panel, Cables, DB, MCB, MCCB, Capasitor, Light Fixtures, AC System cable work, Light Pole, Facade Lighting, Data-TV-Telephone, CCTV network and Equiment etc

Supplyinhg certified, trained 2+Year Experienced / Electrician man-power for the Monthly Basis for 2nd Year Scope of work to Operate & maintnance of the following Work Lt Panel, Cables, DB, MCB, MCCB, Capasitor, Light Fixtures, AC System cable work, Light Pole, Facade Lighting, Data-TV-Telephone, CCTV network and Equiment etc

Supplyinhg certified, trained 2+Year Experienced / Electrician man-power for the Monthly Basis for 3rd Year Scope of work to Operate & maintnance of the following Work Lt Panel, Cables, DB, MCB, MCCB, Capasitor, Light Fixtures, AC System cable work, Light Pole, Facade Lighting, Data-TV-Telephone, CCTV network and Equiment etc

Supplyinhg certified, trained 2+Year Experienced Electrician man-power for the Monthly Basis for 4th Year Scope of work to Operate & maintnance of the following Work Lt Panel, Cables, DB, MCB, MCCB, Capasitor, Light Fixtures, AC System cable work, Light Pole, Facade Lighting, Data-TV-Telephone, CCTV network and Equiment etc

Liaoning with Local Electricity Board & Electrical Inspector for upgradation of Existing 11KV HT Power & Electrical inspector certification in totality to charge the power other related accessories. etc. complete. Charges for doing liasioning work for obtaining the necessary clearances from the Electrical inspector/competent Authorities for the total Electrical installation, Elevator Inspection, co-ordinating with various agencies. All necessary drawings, calculations, test certificates, etc. as required by the seauthorities shall be prepared and furnished by the EPCV endor. Any modification / rectification as required by these authorities shall be carried out by the EPCV endor at free of cost. The fees required to be paid to these authorities for inspection shall be borne by Owner on production of documentary evidences.

Liaoning with local authority / Fire Dept for roof top solar system Charges for doing liasioning work for obtaining the necessary clearances from the Electrical inspector/competent Authorities for the total Electrical installation, Elevator Inspection, co-ordinating with various agencies. All necessary drawings, calculations, test certificates, etc. as required by the seauthorities shall be prepared and furnished by the EPCV endor. Any modification / rectification as required by these authorities shall be carried out by the EPCV endor at free of cost. The fees required to be paid to these authorities for inspection shall be borne by Owner on production of documentary evidences.

TIRUPATI SARJAN LIMITED