SPECIAL REPAIR OF 2 NOS MAIN ENTRANCE GATE ACP WITH IRON GATE AND BOUNDARY WALL WITH STONE GRIT IN THE OFFICE OF THE CDA JABALPUR UNDER GE(EAST) JABALPUR

Amount

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil to a distance n exc 50m and depositing where directed at a level not exceeding 1.5m above starting point complete all as specified and directed.

M&L for PCC ( 1:4:8) type D2 (40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for rough finished, flat formwork to sides of concrete foundation, footings, bases of columns and raft beams, sides and soffits (if any) of foundation and plinth beams and similar works vertical or batter complete all as specified and directed.

Material and labour for formwork for sides of pillars, posts, struts, piers, columns or stanchions rough finished, flat, complete all as specified and directed.

Material and labour for formwork to sides and soffits of floor or roof beam, beam haunchings, girders, lintels, cantilevers, shelves including supports overhangs etc also splays between floors and beams etc rough finished, flat surfaces complete all as specified and directed.

Material and labour for formwork to soffits of suspended slabs such as roof salbs and similar work not exceeding 200mm thick (horizontal or slopping)supported on wall or beams rough finished surfaces of concrete complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 8 mm dia as in stirrups, spacers and binders for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M & L for cement concrete M-25 design mix in foundation including rafts, footings, foundations, beams, plinth beams, bases of columns etc, basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

Material and labour for RCC M-25 design mix in columns, posts, piers and struts etc complete all as specified and as directed.

Material and labour for RCC M-25 design mix in beams, cantilevers, bressummers, lintel over 1.5m span complete all as specified and as directed.

M&L for RCC design mix M-25 in slabs supported on walls, beams and columns in floors and the like complete all as specified and as directed.

Material and labour for brick work with flyash bricks , curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

Labour only for brick work with flyash bricks , curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed. ( Note : Serviceable bricks retrieved against dismantling shall be re-used)

Material and labour for rendering 15mm thick in cement mortar 1:4 on fair faes of brick wall or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5mm thick in cement mortar 1:3 as in ceiling finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over and including one coat of chalk whitening complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of 100% premium acrylic emulsion pait having VOC les than 50gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resitance exterior paint of required shade (Company depot, tinted) with silicon additie @ 1.43 litre/10 Sqm over and incl priming coat of exterior primer applied @ 0.90 litre/10 Sqm complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of whitewash complete all as specified and as directed.

M&L for 100mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base for flooring complete all as specified and as directed.

M&L for machine cut kota stone slab in flooring 20-25mm thick over cement screed bed and jointed in neat cement slurry mixed with pigments to match the shade of the slab including rubbing and polishing, laid over and including screed bed 15mm thick in cement mortar 1:6 for laying of kota stone slab complete all as specified and directed.

M&L for kota stone slab 18-20mm thick in risers or steps, skirting, dado and pillar fixed over cement plaster laid and jointed in neat cement slurry mixed with pigments to match the shade of the slab including rubbing and polishing, laid over and including screed bed 10mm thick in cement mortar 1:3 complete all as specified and directed.

M&L for 75mm thick PCC(1:3:6) Type C-1 (20mm graded crushed stone aggregate) as in plinth protection complete all as specified and directed.

M&L for applying evenly tack coat of hot blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm after cleaning the surfaces over & including a coat of bitumen primer @ 0.30 litre/ sqm consisting of 3/4 part bitumen of grade 85/25 and 1/4 part of kerosene oil on the top of prepared roof surfaces complete all as specified & directed.

M&L for unrolled over the bitumen coated surface, 3mm thick spun bonded non-woven polyester reinforced APP modified water proofing membrane weighing not less than 3.0 Kg/Sqm with minimum side over lap of 100mm and end over lap of 150 mm shall be sealed by flame as per manufacturer's instructions complete all as specified & directed. Note:- Suitable embedment of APP modified water proofing membrane shall be ensured into walls/parapet walls, special care shall be taken in laying APP modified water proofing membrane in situations such as drain/ expansion joints etc.

S&F in steel window with side hung shutters including projecting type hinges with steel handle, and steel pegstay, complete with glazing bars dovetailed or welded complete all as specified and directed.

Ditto as per item No 29 above but without glazing bars.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars and similar work conforming to Fe- 290 ( Gde-E-165) complete all as specified and as directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts). No claim whatso ever shall be entertained by Govt on this account.

M&L 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc. 0.5 sqm in each pane complete all as specified and as directed.

S & F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

M&L for pressed steel door frame of size 105X60mm for doors with one or more rebates including necessary fixing lugs, hinges, locks, strike plate etc complete all as specified and as directed.

M&L for factory made 35mm thick second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, framed, panelled shutter (two or three panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stiles as per IS: 1003 (Part-I), kiln seasoned complete all as specified & directed.

S&F 125mm long extruded aluminum alloy handles, fabricated type anodised fixed with screws complete all as specified & directed.

S & F 200mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S & F 300 mm long aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified.

S&F 140mm floor door stopper of aluminIum alloy body and tongue, anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of primer red oxide domplete all as specified.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint ordinary tint over one coat of pink primer complete all as specified & directed.

Demolition of cement concrete of any description (unreinforced) in ground floors and paving not exceeding 15 cms thickness (below or above ground level) including removal of debris to out side MD land complete all as specified & directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete including removal of debris to out side MD land complete all as specified & directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed trusses complete all as specified and directed.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with the shade of granite stone including grinding and polishing, over and including 10mm thick cement plaster in cement mortar 1:3 complete all as specified and as directed.

M&L for aluminium angle/tee/flat sections fixed to RCC columns/RCC beams or walls at any height with rawl plugs and screws of appropriate size including all scaffolding required as in framework for fixing ACP wall panelling complete all as specified and as directed.

Material and labour for aluminum composit panelling of approved colour/texture fixed over alluminium framework on walls or, columns, beams etc as directed including necessary formwork complete all as specified.

M&L for stainless steel work in writing letters of any pattern, section and size of grade-304 with and including stainless steel nuts and bolts or screws complete all as specified and directed.

M&L for formation sign of size 500X500mm made out of stainlees steel sheet 1mm thicknesss including fixing with stainless steel nuts and bolts or screws omplete all as specified and as directed.

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement:4 coarse sand) furrowing the under layer with scratching tool, applying the cement slurry on the under layer @ 3Kg of cement per sqm, top layer 15mm thick cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand:2 Stone chipping10mm nominal size)in panels with grooves all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and directed. ( Note : Payment of making grooves will be measured and paid for separately)

M&L for forming square grooves in plaster n exc 12mm deep and n exc 15mm on front face complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coat of cement base paint over one coat of chalk whitening complete all as specified and as directed.

Schedule of credit amount of Rs 23710.00 to be deducted during AOC

M/s Ram Associates

LAL SINGH & SONS