Construction of open type removable Temporary shed for MSS at South side of ATF building in NIOT Campus

Amount

Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 300 mm dia piles

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) Note i)River sand should be used ii) RMC concrete should be used iii) concrete must cube test 7th day , 28th day for compressive strength of concrete to submit orginal test report.

Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Consolidation of sub grade With road roller/ hand roller of 5 to 6 tonne operation weight capacity suitable roller as per site condition over the filled up soil in layers not exceeding 200mm depth dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) Note i)River sand should be used ii) RMC concrete should be used iii) concrete must cube test 7th day , 28th day for compressive strength of concrete to submit orginal test report.

Steel reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S (non modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement:4 coarse sand)

Half brick masonry with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundations and plinth in. Cement mortar 1:3 (1 cement: 3 coarse sand)

15mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement:6 fine sand)

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position, applying a priming coat of approved steel primer all complete. Note : make-VIZAG/TATA/SAIL/JSW

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and fixing precoated galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :Powder coated aluminium (minimum thickness of powder coating 50 micron) Note:- Door(2x2.1)-1nos window (3x1.2)-3nos window (2x1.2)-4nos

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required ,nessary fittings, lock, door stoper, hydrolice door closer) Powder coated aluminium (minimum thickness of powder coating 50 micron) Note:- Door(2x2.1)-1nos window (3x1.2)-3nos window (2x1.2)-4nos

Providing and fixing 4.00mm thick Aluminium composite panel of approved make in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket and requird fittings etc. All complete as directed by engineer-in-charge Note:- Door(2x2.1)-1nos Including glass

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) Note:- Door(2x2.1)-1nos window (3x1.2)-3nos window (2x1.2)-4nos

Finishing with Food Grade Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On concrete work (new work)

Wall painting with Interior wall primer paint of approved brand and manufacture to give an shade: one or more coats. Note: apcolite advanced heavy duty emulsion appropriate priming coat or equivalent.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on old work Note: apcolite advanced heavy duty emulsion or equivalent.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Gutter (600-700 mm over all girth)

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including all nessary fittings and jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Supply and laying of 3.5C x 50sqmm PVC insulated Aluminium armoured 1.1kV graded XLPE UG cable along the new cable trench / MS angle.The job including of Special clamp fixing and minor welding work as per site condition Location: ATF front side New Power panel to ATF rear MSS New shed Sub panel. Make : Polycab/KEI/SN cab/ RR

Supply and Making of end termination with single compression gland (3.5C x 50sqmm) suitable crimping lugs.The gland should be single earthed by suitable copper wire and earth strip. Location: *ATF front side New Power panel- 1no. *ATF rear MSS New shed Sub panel - 1no. Make: Comet / Comex

Supply and making of joint kit for 50 sqmm Aluminium cable. Location :Canteen /NIOT campus Make : Polycab/RR kabel/KEI

Supply and laying of 4C x 16sqmm PVC insulated Copper armoured 1.1kV graded XLPE UG cable along the MS angle.The job including of Special clamp fixing and minor welding work as per site condition Location: Sub panel to New 6way VTPN. Make : Polycab/KEI/SN cab/ RR

Supply and Making of end termination with single compression gland (4C x 16sqmm) suitable crimping lugs.The gland should be single earthed by suitable copper wire and earth strip. Location: *ATF rear MSS New shed Sub panel - 1no. * New 6way VTPN - 1no. Make: Comet / Comex

Supply and fixing of 6way Three phase double door protection MCB VTPN DB along the MS frame with following rating of MCB's. A) 63A FP MCB - 1no.(Incomer's) B) 25A TP MCB - 3nos.(For Environmental chamber & A/C's) C) 20A SP MCB - 7nos.(For Corrosion chamber & Power Socket's) D) MCB Dummy - 2nos. Make : Legrand/Hager

Supply and laying of 4C x 6sqmm PVC insulated Copper armoured 1.1kV graded XLPE UG cable along the new cable trench/MS angle.The job including of Special clamp fixing and minor welding work as per site condition. Location: ATF/GF/LDB panel to ATF rear MSS New shed LDB. Make : Polycab/KEI/SN cab/ RR

Supply and Making of end termination with single compression gland (4C x 6sqmm) suitable crimping lugs.The gland should be single earthed by suitable copper wire and earth strip. Location: * ATF/GF/LDB panel - 1no. * ATF rear MSS New shed 12way SP LDB - 1no. Make: Comet / Comex

Supply and fixing of 12way Single phase double door protection DB along the MS angle with following rating of MCB's.The job including of Special clamp fixing and minor welding work as per site condition. A) 32A DP MCB - 1no. B) 10A SP MCB - 8nos. D) MCB Dummy - 2nos. Location: ATF rear MSS New shed Make : Legrand/Hager

Supply and concealing of 2R x 1.5sqmm and 1R x 1.5sqmm FRLS PVC insulated copper conductor graded to 1.1kV ,single core multistrand cable using suitable ISI PVC pipe along the MS angle using special clamp as required as per site condition. Location:ATF rear MSS New shed lighting. Make : * Conductor : Polycab/KEI/SN cab/RR * Pipe : Avon blast/Bajaj blast/Modi

Supply and concealing of 2R x 2.5sqmm and 1R x 2.5sqmm FRLS PVC insulated copper conductor graded to 1.1kV ,single core multistrand cable using suitable ISI PVC pipe along the MS angle using special clamp as required as per site condition. Location : ATF rear MSS New shed sockets & Main light circuit's. Make : * Conductor : Polycab/KEI/SN cab/RR * Pipe : Avon blast/Bajaj blast/Modi

Supply and concealing of 4R x 4sqmm and 2R x 2.5sqmm FRLS PVC insulated copper conductor graded to 1.1kV ,single core multistrand cable using suitable ISI PVC pipe along the MS angle using special clamp as required as per site condition. Location : ATF rear MSS New shed A/C's,Environmental chamber & Corrosion chamber. Make : * Conductor : Polycab/KEI/SN cab/RR * Pipe : Avon blast/Bajaj blast/Modi

Supply and fixing of 4module metal box comprising of following accessories along the MS angle. a) 4Module plate - 1no b) 5 switch - 4nos Location : For Bay lights & Tube lights control Make : MK / Legrand Anchor roma

Supply and fixing of 6module metal box comprising of following accessories along the MS angle. a) 6Module plate - 1no b) 15 switch - 2nos c) 15/5A multipin socket - 2no's Location : For Lab LDB & PDB power. Make : MK / Legrand Anchor roma

Supply,Installation,Testing and commissioning of Single phase 6way IP20 powder coated Metal Enclosure with C25A FP MCB & 2nos MCB Dummy plate along the wall.(For A/C power) Location: ATF rear MSS New shed Make :- SPN DB - Legrand/Hager/L&T. MCB - Legrand/Hager/L&T

Supply and fixing of 4 Feet 18 to 24W LED batten Tubelight fitting along the MS angle.The job including of Special clamp fixing and minor welding work as per site condition. (Color : Cool white) Location: ATF rear MSS New shed Make :PHILIPS/CG/OSRAM/BAJAJ

Supply and fixing of IP66 LED weather proof 50 to70W, 120 degree aluminium die cast green up low bay light.The job including of Special safety chain,clamp fixing and minor welding work as per site condition. (Color : Cool white) location: ATF rear MSS New shed. Make:PHILIPS/CG/OSRAM/BAJAJ/Aster led,Syska led.

Supply and fixing of IP66 LED weather proof 30W, street light fitting with suitable arm along the shed out side MS angle.The job including of Special clamp fixing and minor welding work as per site condition. (Color : Cool white) location: ATF rear MSS New shed. Make:PHILIPS/CG/OSRAM/BAJAJ/Aster led,Syska led.

Supply and fixing of IP 65 weather proof 4way thermo plastic box with along the MS frame comprising of following accessories.(For street light control) *C10A SP MCB - 2No. *MCB Dummy - 2nos. Location: ATF rear MSS New shed Entrance. Make:- Thermoplastic box - Hensel,sintex. MCB - Hager,Legrand.

Supply,Erection,Testing and Commissioning of IP66 double door weather proof outdoor type Panel,Bottom entry Floor mounting type,dust and vermin proof,constructed of 14SWG CRCA sheets,compartmentalised,modular type and powder coated as per specification mentioned in NIT, Page No.29

Supply,Erection,Testing and Commissioning of indoor type PDB Panel,wall mounting type,dust and vermin proof,constructed of 14SWG CRCA sheets,compartmentalised,modular type and powder coated as per specification mentioned in NIT, Page No.29 - 30

TOTAL WITHOUT GST

TOTAL

Varam Constructions (BID ID -3155482)

JPS CONSTRUCTIONS (BID ID -3155290)

M SELVAM (BID ID -3151984)

prabu&company (BID ID -3160393)