Two miscellaneous works under Senior Divisional Engineer (South) Jabalpur jurisdiction :- Part 1 - Upgradation/Modification of RPF barrack at Pipariya under Assistant Divisional Engineer Pipariya sub division. Part 2 - Construction of ADEN office under Assistant Divisional Engineer Narsinghpur sub division.

Item- 2 All schedule items of DSR 2021

S No. Item No Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

JABALPUR DIVISION-ENGG/WEST CENTRAL RLY

Earth work in excavation by mechanical means

(Hydraulic excavator)/manual means over

areas (exceeding 30 cm in depth, 1.5 m in

2.6 width as well as 10 sqm on plan) including

getting out and disposal of excavated earth

lead upto 50 m and lift upto 1.5 m, as directed

by Engineer-in-charge.

2.25A Excavating, supplying and filling of local earth cum 450 368.65 165892.5

(including royalty) by mechanical transport

upto a lead of 5km also including ramming and

watering of the earth in layers not exceeding

20 cm in trenches, plinth, sides of foundation

2.27 Supplying and filling in plinth with sand under cum 180 2161.2 389016

3 floors, including watering, ramming,

consolidating and dressing complete.

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement

concrete of specified grade excluding the cost

of centering and shuttering - All work up to

derived from natural sources : 4 graded stone

aggregate 20 mm nominal size derived from

natural sources)

derived from natural sources : 6 graded stone

aggregate 20 mm nominal size derived from

natural sources)

5.0 REINFORCED CEMENT CONCRETE

5.1S CAST IN SITU

Providing and laying in position specified grade

of reinforced cement concrete, excluding the

cost of centering, shuttering, finishing and

reinforcement - All work up to plinth level :

derived from natural sources: 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

Reinforced cement concrete work in walls (any

thickness), including attached pilasters,

buttresses, plinth and string courses, fillets,

5.2 columns, pillars, piers, abutments, posts and

struts etc. above plinth level up to floor five

level, excluding cost of centering, shuttering,

finishing and reinforcement :

derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

5.9S FORM WORK

Centering and shuttering including strutting,

propping etc. and removal of form for

5.9.1 Foundations, footings, bases of columns, etc. Sqm 150 307.95 46192.5

for mass concrete

5.9.3 Suspended floors, roofs, landings, balconies Sqm 360 766.55 275958

and access platform

5.9.5 Lintels, beams, plinth beams, girders, Sqm 460 608.35 279841

bressumers and cantilevers

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Sqm 250 804.25 201062.5

5.22S STEEL REINFORCEMENT

JABALPUR DIVISION-ENGG/WEST CENTRAL RLY

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete upto plinth

5.22.6 Thermo-Mechanically Treated bars of grade Kg 22000 89.65 1972300

Fe-500D or more.

6.0 MASONRY WORK

6.26S EXPOSED BRICK WALL

Brick work with common burnt clay selected

F.P.S. (non modular) bricks of class designation

7.5 in exposed brick work including making

horizontal and vertical grooves 10 mm wide 12

mm deep complete in cement mortar 1:6 (1

cement : 6 coarse sand)

13 6.26.1 From ground level upto plinth level cum 25 6849.5 171237.5

Brick work with clay flyash F.P.S. (non

modular) brick of class designation 7.5 in

superstructure above plinth level up to floor

five level in :

8.0 CLADDING WORK

8.20S STONE WORK DRY CLADDING

8.31 Providing and fixing Ist quality ceramic glazed Sqm 140 1063.45 148883

wall tiles conforming to IS: 15622 (thickness to

be specified by the manufacturer), of approved

make, in all colours, shades except burgundy,

bottle green, black of any size as approved by

15 Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per

sqm, including pointing in white cement mixed

with pigment of matching shade complete.

9.0 WOOD AND P.V.C. WORK

Providing and fixing 25 mm thick shutters for

cup board etc. :

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I)

decorative type, core of block board

9.20 construction with frame of 1st class hard wood

and well matched teak 3 ply veneering with

vertical grains or cross bands and face veneers

on both faces of shutters.

9.20.1 35 mm thick including ISI marked Stainless Sqm 30 3086.1 92583

Steel butt hinges with necessary screws

ANODISED ALUMINIUM FITTINGS (ALL FITTINGS

SHALL BE ISI MARKED)

Providing and fixing aluminium sliding door

bolts, ISI marked anodised (anodic coating not

9.96 less than grade AC 10 as per IS : 1868),

transparent or dyed to required colour or

shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI

marked, anodised (anodic coating not less than

9.97 grade AC 10 as per IS : 1868 ) transparent or

dyed to required colour or shade, with

necessary screws etc. complete :

Providing and fixing aluminium handles, ISI

marked, anodised (anodic coating not less than

9.100 grade AC 10 as per IS : 1868) transparent or

dyed to required colour or shade, with

necessary screws etc. complete :

JABALPUR DIVISION-ENGG/WEST CENTRAL RLY

Providing and fixing aluminium hanging floor

door stopper, ISI marked, anodised (anodic

coating not less than grade AC 10 as per IS :

1868) transparent or dyed to required colour

and shade, with necessary screws etc.

Providing and fixing wire gauge shutters using

stainless steel grade 304 wire gauge with wire

of dia 0.5 mm and average width of aperture

1.4 mm in both directions for doors, windows

and clerestory windows with necessary screws

9.141 Providing and fixing PVC Door Frame of size Metre 40 462.25 18490

50x47 mm with a wall thickness of 5 mm (+/-

0.2 mm), made out of single piece extruded

PVC profile, with mitred cut joints and joint

with 2 nos of PVC bracket of size 190 mm x

100 mm long arms of cross section size 35 x

15 mm & self driven self taping screws, the

vertical door profiles to be reinforced with

21 40x20 mm M.S. rectangular tube of 0.8 mm ,

including providing EPDM rubber gasket

weather seal throughout the frame, including

jointing 5 mm PVC frame strip with PVC solvent

cement on the back of the profile. The door

frame to be fixed to the wall using 8 x100 mm

long anchor fasteners complete, all as per

manufacturer's specification and direction of

Engineer -in- charge.

35 mm thick factory made Solid panel PVC

Door shutter, made out of single piece

extruded soild PVC profiles, 5 mm (+/- 0.2

mm) thick, having styles & rails (except lock

rail) of size 95 mmx 35 mm x 5 mm, out of

which 75 mm shall be flat and 20 mm shall be

tapered (on both side), having one side

thickness of 15 mm integrally extruded on the

hinge side of the profile for better screw

holding power, including reinforcing with MS

tube of size 40 mm X 20 mm x 1 mm, joints of

styles & rails to be mitered cut & joint with the

help of PVC solvent cement, self driven self

tapping screws & M.S. rectangular pipes

bracket of size 190 mm X 100 mm of cross

section size 35 mm x 17 mm x 1 mm at each

corner. Single piece extruded 5 mm thick solid

PVC Lock rail of size 115 mm x 35 mm, out of

which 75 mm to be flat and 20 mm to be

tapered at both ends, having 15 mm solid core

in middle of rail section integrally extruded,

fixing the styles & rails with the help of solvent

and self driven self tapping screws of 125 mm

x 11 mm, including providing 5 mm Single

piece solid PVC extruded sheet inserted in the

door as panel, all complete as per

manufacturer's specification and direction of

Engineer-in-charge.

22 9.142.2 Decorative finish (wood grained finish) Sqm 15 4018.4 60276

10.0 STEEL WORK

Steel work in built up tubular (round, square or

rectangular hollow tubes etc.) trusses etc.,

including cutting, hoisting, fixing in position

and applying a priming coat of approved steel

primer, including welding and bolted with

special shaped washers etc. complete.

JABALPUR DIVISION-ENGG/WEST CENTRAL RLY

Steel work welded in built up sections/ framed

work, including cutting, hoisting, fixing in

10.25 position and applying a priming coat of

approved steel primer using structural steel

etc. as required.

10.25.2 In gratings, frames, guard bar, ladder, railings, Kg 5000 142.3 711500

brackets, gates and similar works

10.28 Providing and fixing stainless steel ( Grade Kg 100 612.25 61225

304) railing made of Hollow tubes, channels,

plates etc., including welding, grinding,

buffing, polishing and making curvature

(wherever required) and fitting the same with

necessary stainless steel nuts and bolts

complete, i/c fixing the railing with necessary

25 accessories & stainless steel dash fasteners ,

stainless steel bolts etc., of required size, on

the top of the floor or the side of waist slab

with suitable arrangement as per approval of

Engineer-in-charge, (for payment purpose only

weight of stainless steel members shall be

considered excluding fixing accessories such

as nuts, bolts, fasteners etc.).

11.0 FLOORING

11.16S TILE FLOORING

Chequerred precast cement concrete tiles 22

mm thick in footpath & courtyard, jointed with

neat cement slurry mixed with pigment to

match the shade of tiles, including rubbing and

cleaning etc. complete, on 20 mm thick bed of

cement mortar 1:4 (1 cement: 4 coarse sand).

26 11.20.3 Dark shade pigment using ordinary cement Sqm 150 983.95 147592.5

11.26S KOTA STONE FLOORING

Kota stone slab flooring over 20 mm (average)

thick base laid over and jointed with grey

cement slurry mixed with pigment to match

the shade of the slab, including rubbing and

polishing complete with base of cement mortar

1 : 4 (1 cement : 4 coarse sand) :

11.37S CERAMIC GLAZED TILES

11.37A Providing and fixing 1st quality ceramic glazed Sqm 50 938.5 46925

floor tiles conforming to IS : 15622 (thickness

to be specified by the manufacturer ) of

approved make in all colours, shades except

burgundy, bottle green, black of any size as

approved by Engineer-in-Charge in skirting,

risers of steps and dados over 12 mm thick

bed of cement Mortar 1:3 (1 cement: 3 coarse

sand) and jointing with grey cement slurry @

3.3kg per sqm including pointing in white

cement mixed with pigment of matching

shade complete.

11.41S VITRIFIED FLOOR TILES

Providing and laying Vitrified tiles in floor in

different sizes (thickness to be specified by the

manufacturer) with water absorption less than

0.08% and conforming to IS:15622, of

approved brand & manufacturer, in all colours

and shade, laid on 20 mm thick cement mortar

1:4 (1 cement: 4 coarse sand) jointing with

11.41A grey cement slurry @3.3 kg/sqm including

grouting the joints with white cement and

matching pigments etc. The tiles must be cut

with the zero chipping diamond cutter only .

Laying of tiles will be done with the notch

trowel, plier, wedge, clips of required

thickness, leveling system and rubber mallet

for placing the tiles gently and easily.

JABALPUR DIVISION-ENGG/WEST CENTRAL RLY

Double charge vitrified tile polished finish of

Providing and laying Polished Granite stone

flooring in required design and patterns, in

linear as well as curvilinear portions of the

building all complete as per the architectural

drawings with 18 mm thick stone slab over 20

mm (average) thick base of cement mortar 1:4

(1 cement : 4 coarse sand) laid and jointed

with cement slurry and pointing with white

cement slurry admixed with pigment of

matching shade including rubbing , curing and

polishing etc. all complete as specified and as

directed by the Engineer-in-Charge.

11.56.1 Polished Granite stone slab colour of Black, Sqm 50 3908.8 195440

Cherry/Ruby Red or equivalent

12.0 ROOFING

Providing, fixing and embedding sand cast iron

accessories for rain water pipes in the masonry

12.40 surrounded with 12 mm thick cement mortar

of the same mix, as that of masonry (lead

caulking will be paid for separately):

Providing and fixing on wall face unplasticised

Rigid PVC rain water pipes conforming to IS :

13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap

for thermal expansion, (i) Single socketed

Providing and fixing on wall face unplasticised -

PVC moulded fittings/ accessories for

unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS : 5382,

leaving 10 mm gap for thermal expansion.

12.50 Providing and fixing precoated galvanised iron Sqm 50 671.55 33577.5

profile sheets (size, shape and pitch of

corrugation as approved by Engineer-in-

charge) 0.50 mm (+ 0.05 %) total coated

thickness with zinc coating 120 grams per sqm

as per IS: 277, in 240 mpa steel grade, 5-7

microns epoxy primer on both side of the

sheet and polyester top coat 15-18 microns.

Sheet should have protective guard film of 25

32 microns minimum to avoid scratches during

transportation and should be supplied in single

length upto 12 metre or as desired by

Engineer-in-charge. The sheet shall be fixed

using self drilling /self tapping screws of size

(5.5x 55 mm) with EPDM seal, complete upto

any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters

and trusses and including cutting to size and

shape wherever required.

13.0 FINISHING

13.1S CEMENT PLASTER (IN FINE SAND)

13.1 12 mm cement plaster of mix :

13.16S 6MM CEMENT PLASTER

13.16 6 mm cement plaster of mix :

13.25 Extra for plastering:

JABALPUR DIVISION-ENGG/WEST CENTRAL RLY

13.26 Providing and applying plaster of paris putty of Sqm 1600 214.3 342880

2 mm thickness over plastered surface to

prepare the surface even and smooth

13.44S EXTERIOR FINISHING

Finishing with Deluxe Multi surface paint

13.48 system for interiors and exteriors using Primer

as per manufacturers specifications :

13.48.3 Painting Steel work with Deluxe Multi Surface Sqm 200 140.05 28010

Paint to give an even shade. Two or more coat

36 applied @ 0.90 ltr/10 sqm over an under coat

of primer applied @ 0.80 ltr/10 sqm of

approved brand and manufacture

Wall painting with acrylic emulsion paint of

13.60 approved brand and manufacture to give an

16.0 ROAD WORK

16.49S MISCELLANEOUS

Providing and laying factory made chamfered

edge Cement Concrete paver blocks in

footpath, parks, lawns, drive ways or light

traffic parking etc, of required strength,

thickness & size/ shape, made by table

vibratory method using PU mould, laid in

required colour & pattern over 50mm thick

16.91 compacted bed of sand, compacting and

proper embedding/laying of inter locking paver

blocks into the sand bedding layer through

vibratory compaction by using plate vibrator,

filling the joints with sand and cutting of paver

blocks as per required size and pattern,

finishing and sweeping extra sand. complete

all as per direction of Engineer-in-Charge.

16.91.1 60mm thick cement concrete paver block of Sqm 150 932.35 139852.5

38 M-35 grade with approved colour, design &

17.0 SANITARY INSTALLATIONS

Providing and fixing white vitreous china

pedestal type water closet (European type

W.C. pan) with seat and lid, 10 litre low level

white P.V.C. flushing cistern, including flush

17.2 pipe, with manually controlled device (handle

lever), conforming to IS : 7231, with all fittings

and fixtures complete, including cutting and

making good the walls and floors wherever

17.2.1 W.C. pan with ISI marked white solid plastic Each 1 5540.55 5540.55

Providing and fixing Stainless Steel A ISI 304

(18/8) kitchen sink as per IS:13983 with C.I.

brackets and stainless steel plug 40 mm,

including painting of fittings and brackets,

cutting and making good the walls wherever

17.10.1 Kitchen sink with drain board

Providing and fixing white vitreous china water

closet squatting pan (Indian type) :

Providing and fixing white vitreous china wash

17.25 basin including making all connections but

excluding the cost of fittings :

18.0 WATER SUPPLY

JABALPUR DIVISION-ENGG/WEST CENTRAL RLY

18.7S C.P.V.C. PIPES

Providing and fixing G.I. pipes complete with

G.I. fittings and clamps, i/c cutting and making

good the walls etc.-Internal work - Exposed on

Providing and fixing G.I. Pipes complete with

G.I. fittings and clamps, i/c making good the

18.11 walls etc. concealed pipe, including painting

with anti corrosive bitumastic paint, cutting

chases and making good the wall :

Providing and fixing G.I. pipes complete with

18.12 G.I. fittings including trenching and refilling

etc.-External work

C.I. SLUICE VALVES/ FIRE HYDRANTS &

18.48 Providing and placing on terrace (at all floor Litre 1000 9.7 9700

levels) polyethylene water storage tank, IS :

12701 marked, with cover and suitable locking

arrangement and making necessary holes for

inlet, outlet and overflow pipes but without

fittings and the base support for tank.

18.54S PTMT FITTINGS

Providing and fixing PTMT bib cock of approved

quality and colour.

18.54.1 15mm nominal bore, 86 mm long, weighing Each 10 109.85 1098.5

not less than 88 gms

Providing and fixing PTMT stop cock of

approved quality and colour.

18.55.1 15 mm nominal bore, 86 mm long, weighing Each 4 103.15 412.6

not less than 88 gms

20.0 PILE WORK

Boring with hydraulic piling rigs with power

units, providing and installing cast in situ

single under reamed piles of specified

diameter and length below pile cap in M-25

cement concrete, to carry a safe working load

20.3 not less than specified, excluding the cost of

steel reinforcement but including the cost of

boring with bentonite solution and the length

of the pile to be embedded in pile cap etc. all

complete. (Length of pile for payment shall be

measured upto to the bottom of pile cap) :

Extra over single under ream for providing

additional bulbs in under reamed piles, under

specified diameter(only the nos. of extra bulbs

are to be paid)

21.0 ALUMINIUM WORK

JABALPUR DIVISION-ENGG/WEST CENTRAL RLY

Providing and fixing aluminium work for doors,

windows, ventilators and partitions with

extruded built up standard tubular sections/

appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS:

1285, fixing with dash fasteners of required

dia and size, including necessary filling up the

gaps at junctions, i.e. at top, bottom and sides

with required EPDM rubber/ neoprene gasket

etc. Aluminium sections shall be smooth, rust

free, straight, mitred and jointed mechanically

wherever required including cleat angle,

Aluminium snap beading for glazing / paneling,

C.P. brass / stainless steel screws, all complete

as per architectural drawings and the

directions of Engineer-in-charge. (Glazing,

paneling and dash fasteners to be paid for

21.1.1 For fixed portion

21.1.1.1 Anodised aluminium (anodised transparent or Kg 550 433.95 238672.5

52 dyed to required shade according to IS: 1868,

Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators

including providing and fixing hinges/ pivots

and making provision for fixing of fittings

wherever required including the cost of EPDM

rubber / neoprene gasket required (Fittings

shall be paid for separately)

21.1.2.1 Anodised aluminium (anodised transparent or Kg 450 531.8 239310

53 dyed to required shade according to IS: 1868,

Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door,

window, ventilator shutters and partitions etc.

with EPDM rubber / neoprene gasket etc.

21.3 complete as per the architectural drawings

and the directions of engineer-in-charge . (Cost

of aluminium snap beading shall be paid in

21.3.1 With float glass panes of 4.0 mm thickness Sqm 50 1019.8 50990

(weight not less than 10kg/sqm)

21.17 Providing and fixing anodised aluminium grill Kg 250 560.85 140212.5

(anodised transparent or dyed to required

shade according to IS: 1868 with minimum

anodic coating of grade AC 15) of approved

design/pattern, with approved standard

section and fixed to the existing window frame

with C.P. brass/ stainless steel screws @ 200

mm centre to centre, including cutting the grill

to proper opening size for fixing and operation

of handles and fixing approved anodised

aluminium standard section around the

opening, all complete as per requirement and

direction of Engineer-in-charge. (Only weight

of grill to be measured for payment).