ADDN/ ALTN TO BLDG NO. SM-1 AT PATIALA UNDER GE (SOUTH) PATIALA

'Notes: (i) Please refer Schedule 'A' Notes of tender documents.

Dismantling of brick tiles or terracing tiles single layers on roofs complete all as specified and directed

Demolition of mud phuska on roof any thickness complete all as specified and directed.

M&L for roughening surfaces of old concrete floor/roof by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M&L for PCC 1:3:6, type B-0 using 12.5mm graded stone aggregates as in padding over roof, minimum thickness at khurra as 25mm to maintain a slope of 1:100, complete all as specified and directed.

M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

M&L for providing and laying 3mm thick APP (Atactic Polyproplene Polymer) modified prefabricated five layer, weight not less than 4.0 Kg/Sqm water proofing membrane black finished, reinforced with non-woven polyster matt make as approved including of a coat of bitumen primer @ 0.40 ltr/sq.m by the same membrane manufacturer of density 0.87 to 0.89 Kg/Ltr at 25 degree C temperature and viscosity 70 - 160 cps Over the coat, 3mm th 5 layered APP membrane shall be laid using butane torch and sealling all joints etc after the surface complete as per standard practice as per manufacturers instructions. The vital physical and chemical parameters of the membrane shall be as under - (i) Joint strength inlongitueinal and transverse direction at 23 degree C as 650/450N/5cms (ii) Tear strength in longitudinal and transverse direction as 300 / 250 N/. Softening point of membrane not less than 150 degree C Cold flexibility upto 20 degree C when tested in accordance with ASTM (D05147) (iii) The laying of membrane shall be got done through the authorised applicator of manufacturer of membrane only complete all as specified and directed.

M&L for Plain Cement Concrete tiles 25cm x 25cm x 22-25mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished laid over 15mm thick screed bed in CM 1:4 complete all as specified and directed

M&L for Plain cement concrete 1:2:4 type B-0 using 12.5mm graded mechanically crushed stone aggregate as in roof kerbs or mud stops and benching, rounded or chamfered on edges, coving shall be 150 mm in radius mixed with acrylic based polymer water proofing compound complete all as specified and directed. Note: WPC shall be paid separately

Taking down of Eaves gulter/rain water pipe (AC rain water pipe /SWG pipe line of any size or pattern), including at fittings, heads, shoes, bends, swan-necks, etc., including cleaning for refuxing or removal from site (measured overall as fixed along the centre line including fitting and accessories) complete all as specified and directed.

S&F UPVC (SWR) Type ‘B’ , 160 mm nominal outside diameter confirming to IS : 13592-1992 single socketed in any length including jointing with lubricant/ PVC cement solvent as per manufacturer’s instruction”, fixed to walls with MS flat iron clamps of size 25 x 3mm, bolts, washers, nuts, nails etc, complete all as specified and as directed. Note: MS flat iron clamps will be measured and paid separately in respective item. Note : Clamps will be measured and paid separately.

S&F UPVC (SWR) bends, 160 mm dia confirming to IS : 14735-99 and jointing with lubricant/ PVC cement solvent as per manufacturer’s instruction”, complete all as specified and as directed.

S&F for MS Clamps, Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay) and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 Nominal Mix type B-1 (using 12.5 mm graded crushed stone aggregate) as in beams, cantilevers, lintels, over 1.5 Mtr Span complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&l for Mild steel TMT bar 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for Form work rough finished to edges of concrete slabs exc 10 cm but not exc 20 cm thick complete all as specified and directed.

M&L for Form work rough finished to edges of concrete slabs exc 5 cm but not exc 10 cm thick complete all as specified and directed.

M&L Formwork (flat surfaces) to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins,arches, pillars etc complete all as specified and directed.

M&L Brick work with Fly ash bricks minimum class designation 100 straight or curved on plan exceeding 6m mean raidus bulit in C:M 1:6 complete all as specified and directed.

Taking down cement plaster of any description, any thickness from external/internal surfaces of walls/soffits/ceilings etc. incl raking out joints, hacking for keys, scrubbibg down with water etc complete all as specified and directed.

M&L rendering 15 mm thick in CM 1:4, on stone masonry surfaces or surface other than fair faces of brick work or concrete surfaces finished fair and even without using extra cement including integral liquid water proofing compound @ 2% by the weight of cement (external) complete all as specified.

Supply only integral liquid Water Proofing Compound ISI marked complete all as specified and directed.

M&L rendering in CM 1:6, 10 mm thick on fair faces brick-work or concrete surfaces finished even and smooth without using extra lime or cement complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on ceiling surfaces, roof projection /chajjas finishing even and smoot without using extra cement complete all as specified and directed.

M&L for complete removal of existing treatment on wall/roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding paper of appropriate grit to make suraface clean , free from dust, loose paint etc by skilled labour complete all as specified and directed. Note: Standing of suraface to be done by mechanical sander with 1500-2700rpm, with internal dust extraction system for clean environment certified by paint manfacturer. Proper masking to be carried out before primer and paint application.

M&L for applying acrylic thick wall care putty on external/internal surfaces of walls/ceilings/soffits etc (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed. Note : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order.

M&L for preparation of surfaces and applying 02 coats of exterior emulsion paint (light shade) with highlighter of any approved shade, @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer and using fully automatic airless spray machine having flow speed of min. 1 lit/minute and pressure of 3300psi complete all as specified and directed.

M&L for preparation of surfaces and applying 02 coats of interior emulsion paint (light shade) @ 10 sq.m/litre/2 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer and using fully automatic airless spray machine having flow speed of minimum 1 ltr/minute and pressure of 3300PSI complete all as specified and directed.

M&L for preparation of surfaces and applying 02 coats of interior emulsion paint (white shade) @ 10 sq.m/litre/2 coats to ceilings surfaces over & including a coat of interior primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer and using fully automatic airless spray machine having flow speed of min. 1 ltr/minute and pressure of 3300PSI complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including CM bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed

Demolition of cement concrete un-reinforced in ground floors and pavings n.exc 15cm thickness complete all as specified and directed.

M&L, cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub-floors, sub-bases, floors and pavings, etc. complete all as specified and directed.

M&L for Polished Glazed Vitrified Tiles (PGVT) joint free premium quality coloured tiles 600 X 1200 mm and 8-10 mm thick, as in skirting/dado etc. laid with 3-5mm spacers and grooves shall be filled with epoxy grout (Pidilite or equivalent) of approved matching colour. in any pattern of light & dark tiles as approved, laid and jointed in suitable adhesive (flexiset H-40 or equivalent as approved) as per manufacturer's instructions and pointed in matching coloured cement based tile joint filler (Roff -Pidilite or equivalent as approved), in floors etc. over & including 10 mm thick Rendering in cement mortar (1:4) over complete all as specified. Note : The rates for labour and material for spacers/ grovers shall be deemed to be included in the quoted unit rates and nothing shall not be measured & paid separately on this account.

M&L for Polished Glazed Vitrified Tiles (PGVT) joint free premium quality coloured tiles 800 X 1600 mm and 8-10 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, laid and jointed in suitable adhesive (flexiset H-40 or equivalent as approved) as per manufacturer's instructions and pointed in matching coloured cement based tile joint filler (Roff -Pidilite or equivalent as approved), in floors etc. laid over & including 20 mm thick screed in cement mortar (1:4) complete all as specified and as directed.

M&L for mat finish anti skid vitrified tile joint free premium quality coloured tiles 600 X 1200 mm and 8-10 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc.laid over & including 20 mm thick screed in cement mortar (1:4) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed.

M&L for Full Body Vitrified Tiles joint free premium quality coloured tiles 600 X 600 mm and 8-10 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 20 mm thick screed in cement mortar (1:4) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.

M&L for machine cut kota stone slab (nearest to 58cmx58cm in size) flooring 20-25mm thick laid over and including 20-22 mm thick screed bed or bedding layer in cement mortar 1:4 as base laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing incl 100mm wide border of Baroda Green Marble complete all as specified and directed.

M&L for pre-polished Baroda Green marble, machine cut as in floorings/ shelves/ steps/ cills/ jambs/ skirting/ border only in tile flooring and the like works and flooring etc, 15-16 mm thick including bull-nose the exposed sides/lengths, set and jointed in cement slurry over & including screed of 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab for fixing on concrete surfaces or with suitable adhesive for fixing incl 100mm wide border of White Marble in flooring complete all as specified and directed. Note : Single piece should be used in steps/cills/jambs/shelves.

M&L for nano tiles 15mm thick of size 800x2400 mm of any shade as approved machine cut as in flooring shelves/steps/counter tops, set and jointed in cement slurry over & including screed of 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive and including bull nose on exposed sides complete all as specified and directed. Note : Single piece should be used in steps/cills/jambs/shelves.

M&L for Granite (Jet Black colour/shade-South Indian) of any type machine cut as in flooring, shelves/steps/counter tops, 18-20 mm thick, set and jointed in cement slurry over & including screed of 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive for fixing and bull nose on exposed sides/lengths complete all as specified and directed. Note : Single piece should be used in steps/cills/jambs/shelves.

M&L Hardcore of broken stone or boulder gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L, Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50 mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints and filling the same with polyureathene (Make : Sikaflex) complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 Sqm each (without taking off shutters from the frames) including all fittings complete all as specified and directed.

Taking down Chowkats or frames exceeding 1.5 Sqm each and not exceeding 4.0 Sqm each (Without taking off shutters from the frames) including grills and fittings complete all as specified and directed.

M&L for Factory made single extruded “Pre-laminated WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat with corner round with back grooves of size 100X62-65 mm”comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardan and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction, specified and directed. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (ii) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid for separately.

M&L for providing and fixing factory made single extruded “Pre-laminated WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick” comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in- Charge all as specified and as directed.

S&F stainless steel finished 202 Grade butt hinges 100mm long complete all as specified and directed.

S&F stainless steel 202 Grade finished 150mm long tower bolts in square shaped with minimum 10mm dia rod complete all as specified and directed.

S&F Stainless Steel 202 Grade Finished curved Handles 150 mm long complete all as specified and directed.

M&L for cement concrete (1:2:4) using 12.50 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats, hold fasts etc., complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction complete all as specified and directed.

S&F Unplasticised Poly Vinyl Chloride (UPVC) 3 track sliding Window with mesh shutter – (2-glass shutter and 1-mesh shutter) duly manufactured using UPVC reinforced profiles (Composition of profile shall consists a minimum of 5.5 PHR of TiO2 and not more than 12 PHR of CaCo3 for every 100 parts of PVC resin) of (112 mm x 52 mm) x 2.20 mm for outer frames, (41 mm x 61 mm) x 2.20mm for sliding shutter frames capable of mounting single glazing system structurally reinforced with hot dip galvanized up to 50 microns of minimum thickness of 1.0/1.2 mm prefabricated & welded through fusion welding. The window sash shall be fitted with 5 mm thick clear float glass of reputed make and mesh shutter frame shall be (42 mm x 61 mm) x 2.0 mm fitted with Vinyl Coated Fiber mesh- on rollers/ pulley duly fixed with Grey colour TPV Gasket for sash & Glazing bead shall be co-extruded with Grey colour soft PVC. Window shall be provided with standard hardware & Single point locking system of touch Lock system. the system is to be installed at the site using anchor fasteners, silicon rubber sealant, easy glazing/deglazing at site etc complete all as specified and as directed.

S&F Powder coated 50 microns extruded aluminium glazing doors & shutters made out of section 83.5x38.10x1.29mm for & chowkats or frame shutters 44.45x44.45x1.29mm for slde ralls made and of glze middle rail. 114.3X44.45X1.29mm for top rails and bottom rails and including 12mm thick High Density Fibre Board pre-laminated on both sides (water proof) below & above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. and aluminium beads 20mm size complete all as specified and directed Including supply and fixing the following items: (a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm 3 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 150mm long -2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per each

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L for providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beed 20mm size with and complete fixed in all respect as specified and directed.

S&F 12mm toughned/tempered frosted glass as in hinged doors, partitions, automatic doors, staircase railings, roof dome works and similar work including cutting to shape, drilling holes required of any size fixed in position with suitable stainless steel 304 Grade all types patch fittings/brackets/catchers/L-connectors/all types hinges (wall to glass/glass to glass)/magnetic seals and including temorary wooden/ply frame wk required to take exact sizes as in staircase railings/ dome work of any shape etc and filling the gaps with silicon all as specified and directed. Note : Stainless steel Hardware will be paid separately under respective items.

S&F double cylinder cam action floor spring with closing force EN4 suitable for max door weight 150 Kg, max door width 1100mm with closing speed 130-10º, final closing speed 10-0º, hold open - 90º, approx weight of floor spring 6Kg, with installation dimensions of size 306x108x40mm fixed in position as per instructions of manufacture including S&F top fittings/hardware from same manufacturer complete all as specified and directed.

S&F H type pull glass door Handles of size 25x300/450 mm stainless steel 304 Grade with back to back installation incl all accessories like gasket, grub screws etc fixed in position as per instructions of manufacture complete all as specified and directed.

S&F re-inforing rod 19mm dia at top of showers etc stainless steel incl all accessories fixed in position as per instructions of manufacture complete all as specified and directed.

S&F all types hinges (wall to glass/glass to glass) stainless steel 304 Grade and PSS finish suitable for 10mm glass as in showers complete fixed in position as per instructions of manufacture complete all as specified and directed.

S&F all types connectors/ brackets/ catchers etc (L-shaped, wall to glass, glass to glass, floor to glass) stainless steel 304 Grade and suitable for 10-12mm glass as in showers/partitions/doors etc complete fixed in position as per instructions of manufacture complete all as specified and directed.

S&F all types patch fittings stainless steel 304 Grade and suitable for 10-12mm glass as in showers/partitions/doors etc complete fixed in position as per instructions of manufacture complete all as specified and directed.

S&F Aluminium (extruded section) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F 300mm, mild steel ordinary rat tail rod (helical type) pattern springs including roller and roller plate complete all as specified and directed.

S&F Venetian Blinds with 100% Polyester Fabric of thickness 0.4mm (±5%) and weight not less than 169g/sq.m (±5%) roller type for windows of colour/shade as approved complete fixed in position inclusive S&F matching palmets from same manufacturer and all accessories and hardwares for fixing and operation, all as recommended by manufacturer, all as specified incl taking down old curtain rods of any type complete all as specifiied and directed.

S&F vitreous china premium/1st quality wall hung water closet rimless of size 555 x 370 x 365 mm with P trap white/ivory/off white including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc., and incl. plastic seat cover soft closing type as recommended by manufacturer for particular model closed pattern with flat bottom etc; and incl S&F of all necessary accessories set like rag bolts/gel gasket/hinges etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified and directed.

S&F concealed flushing cistern of PVC with dual flushing system and half frame, valveless syphonic action type, with inlet/outlet, ball valve, float and including brackets and connection to pipe etc. and incl S&F of all necessary accessories/installation kit and 'S' type drain pipe connetion set for wall hung WC etc as recommended by manufacturer for fixing, packing and including S&F of actuator knob/flush plates as approved complete in all respect all as specified and directed.

S&F vitreous china premium/1st quality wash down water closet pan floor mounting (pedestal pattern/EWC) with S/P trap snow white colour of size 520X360X390mm including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc.,with flush pipe and incl. S&F plastic seat cover as recommended by manufacturer closed pattern with flat bottom etc; and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and including and taking down existing of any description/size complete in all respect all as specified and directed. Note : EWC with S trap will be provided only on G.F. and other remaining floors will be provided with P trap EWCs.

S&F health faucet with 8mm dia and 1.2 metre long flexible tube in chorme finish and wall hook including making connections and fixed in position complete in all respect as specified and directed.

S&F Toilet paper holder with flat recessed type stainless steel complete all as specified and directed.

S&F CP Jet for EWC with chrome finished connction pipe including all accessories for fixing complete in all respect all as specified and directed.

S&F Vitreous China premium quality urinal of size 310x300x555mm snow white colour, and connection to inlet and outlet pipe, and incl S&F of all necessary accessories set like rag bolts/gel gasket/hinges etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified and directed.

S&F Urinal spreader chorme finish for urinals and incl all necessary accessories as recommended by manufacturer for fixing complete in all respect all as specified and directed.

S&F vitreous china premium/1st quality Table Top wash hand basin of size 550 x 400 x 160 mm complete in all respect all as specified and directed.

S&F CP Wall mounted basin spout including hot and cold water supply and operating lever quarter turn consisting of exposed part and concealed part complete all as specified and directed.

S&F Concealed Stop Cock quarter turn, fancy type, CP with long shank and cup, exposed part kit with wall flange, fitting sleeve, operating lever, adjustable wall flange and including regular brass body of concealed stop cock suitable for 15mm line with protection cap fixed in position complete in all respect all as specified and directed.

S&F 15 mm fancy type chromium plated quarter turn angle cock/valve with CP wall flange cast copper alloy screwed down high pressure suitable for 15mm bore pipe or union including taking down old unserviceable existing one complete all as specified and directed.

S&F CP bottle traps 32mm size with 250mm and 175/190mm long wall connection pipes and wall flanges complete fixed in position complete all as specified and directed.

S&F CP waste couplings 32mm size full thread with 80mm height complete fixed in position complete all as specified and directed.

S&F Stainless Steel Towel Rack 600mm long with lower hangers including all accessories as recommended by manufacturer for fixing and complete fixed in position in all respect and taking down existing of any description/size complete all as specified and directed.

S&F 15 mm fancy type chromium plated quarter turn bib tap of long body with CP wall flange cast copper alloy with crutch or butterfly handles screwed down high pressure suitable for 15mm bore pipe or union including taking down old unserviceable existing one complete all as specified and directed.

S&F 450mm long braided hose/PVC connection with 15mm brass nuts complete all as directed and specified.

S&F 5-Way (3 inlets + 2 outlets) single lever concealed diverter consisting of concealed part and exposed parts CP finish made of brass with all accessories as recommended by the manufacturer connected to 15 GI tubing/ 20mm CPVC and S&F of CP spout with wall flange of same model and manufacturer complete all as specified and directed.

S&F overhead shower 200x200mm square shape with 450mm long brass shower arm with wall flange and incl all necessary accessories as recommended by manufacturer for fixing complete in all respect all as specified and as directed.

S&F 5mm thick looking mirror fixed to wall with stainless steel plugs/connecter/spacers/screws etc. chrome finish without any beading, including ends/edges of the mirror to be tapered etched smooth finish etc.complete fixed in position all as specified and directed.

S&F soap dish, stainless steel of suitable size to accommodate soap , tooth brush glass and tooth paste complete all as directed and specified.

S&F stainless steel grating 125x125 mm/ 150x150mm size square shaped with self locking arangement for floor trap with or without hole as required fixed in position complete all as specified and directed.

S&F PVC (HDPE) SWR, 40 mm bore, single socketed in any length with rubber ring joints using solvent cement as per maunfacture instruction, including bends/tee/elbow etc. laid in walls for connecting bottle traps complete all as specified and directed.

Taking up or down existing steel tubing and connections, 25mm bore complete all as directed and specified.

S&F 25mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as directed and specified.

S&F 25mm (OD 27.20mm) CPVC pipes SDR 11, Class-1 for potable hot and cold water distribution supplies lead free confirming to IS-15778 laid on walls/ceiling or laying in floors jointed with suitable CPVC solvent cement of same manufacturer and incl all CPVC SDR 11 fittings as required complete all as specified and directed.

Taking up or down existing steel tubing and connections, 20 mm bore complete all as directed and specified.

S&F 20mm (OD 22.20mm) CPVC pipes SDR 11, class-1 for potable hot and cold water distribution supplies lead free confirming to IS-15778 laid on walls/ceiling or laying in floors jointed with suitable CPVC solvent cement of same manufacturer and incl all CPVC SDR 11 fittings as required and suitable for fixing 15mm CP faucets/ fixtures complete all as specified and directed.

S&F Female Brass Threaded Adaptor (FTA/ FBTA) for 20mm dia CPVC pipe complete all as specified and directed

S&F Brass elbow (3/4 x 1/2) for 20mm dia CPVC pipes complete all as specified and directed

S&F in repair ISI marked doubled layered rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top / cover) 1000 Ltrs capacity hoisted and fixed in position all as specified including 25 mm dia brass float valves, high pressure, with polythene float and fly nut complete screwed for 20mm bore iron pipe and including GI nipple/union of 20mm bore to connect GI tubing to PVC water tank complete all as specified and directed.

Taking down sewage pipe of in any position/size/description complete all as specified and directed.

Taking down bends/floor traps/nahani traps/tee/branch pieces/cowls etc of in any position/size/description complete all as specified and directed.

S&F uPVC (SWR) Type-B pipe single socket 110mm bore confirming to IS 13592-92 in any length with including jointing with lubricant/ PVC cement solvent as per manufacturer’s instruction to UPVC waste pipe, fixed to wall ,including stack clamps out of 50x5 mm flat and 16 mm dia iron stays, including bolts and nuts etc and making necessary connections complete all as specified and as directed.

S&F uPVC (SWR) Type-B pipe single socket 110mm bore confirming to IS 13592-92 in any length with including jointing with lubricant/ PVC cement solvent as per manufacturer’s instruction to UPVC waste pipe, laid in trenches/floor and making necessary connections complete all as specified and as directed.”

S&F uPVC (SWR) Type-B pipe” single socket 75mm bore confirming to IS 13592-92 in any length “with lubricant/ PVC cement solvent as per manufacturer’s instruction”fixed to wall ,including stack clamps out of 50x5 mm flat and 16 mm dia iron stays, including bolts and nuts etc and making necessary connections, complete all as specified and as directed.

S&F uPVC (SWR) Type-B pipe” single socket 75mm bore confirming to IS 13592-92 in any length “with lubricant/ PVC cement solvent as per manufacturer’s instruction” laid in trenches/floor and making necessary connections, complete all as specified and as directed.

S&F uPVC (SWR) confirming to IS : 14735-99 and as per international standards ” bend 110mm bore pipes (any radius) with access door fixed “with lubricant/ PVC cement solvent as per manufacturer’s instruction”complete all as specified and directed.

S&F uPVC (SWR) confirming to IS : 14735-99 and as per international standards ”bend 75mm bore pipes (any radius) with access door fixed “with lubricant/ PVC cement solvent as per manufacturer’s instruction complete all as specified and as directed.

S&F uPVC (SWR) confirming to IS : 14735-99 and as per international standards ” double branch door Tee suitable for 110mm bore pipes ISI marked fixed“with lubricant/ PVC cement solvent as per manufacturer’s instruction” complete all as speciied and as directed.

S&F uPVC (SWR) confirming to IS : 14735-99 and as per international standards ”Single door Tee suitable for 110mm bore pipes ISI marked fixed “with lubricant/ PVC cement solvent as per manufacturer’s instruction” complete all as specified and directed.

S&F uPVC (SWR) confirming to IS : 14735-99 and as per international standards ”Single door Tee suitable for 75mm bore pipes ISI marked fixed “with lubricant/ PVC cement solvent as per manufacturer’s instruction” complete all as speciied and as directed.

S&F uPVC (SWR) confirming to IS : 14735-99 and as per international standards ” Cowls for 110mm bore pipes fixed “with lubricant/ PVC cement solvent as per manufacturer’s instruction” complete all as specified and as directed.

S&F uPVC (SWR) confirming to IS : 14735-99 and as per international standards ” 'P' or 'S' trap 110mm bore with long arm ISI marked fixed “with lubricant/ PVC cement solvent as per manufacturer’s instruction” complete all as speciied and as directed.

S&F PVC (SWR) gully trap 125/110 mm setting and jointing with solvent/rubber ring joint complete all as specified and directed.

Dismentling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillet complete all as specified and directed.

S&F PVC Wall panelling of fluted/louvers/hollow sections/ (colour/pattern as approved by AO) of any size and description complete fixed in position in all respect including supply and fixing of all accessories like fasteners/ screws/solvent/ fillets etc all as recommended by manufacturer all as specified and directed.

S&F anodised aluminium snap grid frame work (size of grid 605x605mm) for false ceiling all as specified including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.l. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

M&L 12 to 12.50mm thick semi-perforated/pin holed particle board/tiles, 600x600 ± 5 mm in size fixed in false ceiling as per manufacturer's instructions to existing frame work or on snap grid as in repairs complete all as specified and directed.

M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

M&L 12 mm thick Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish complete all as specified and as directed.

M&L for preparation of steel and iron surfaces of any description including purlins/ rafters/ trusses/ columns/ struts/railings/ blusterades/ cooler stands/ any frame work etc and the like works complete all as specified and directed.

S&F 18mm thick High Density High Moisture Resistant (HDHMR) exterior Grade Board with both side white balancing (BSB) with density of 850 Kg/cu.m complete all as specified and directed. Note : Board on back side wall will be fixed with minimum 5mm PVC spacers/buffers. The payment for the same deemed to be included in the quoted unit rates.

S&F 18mm thick High Density High Moisture Resistant (HDHMR) exterior Grade Board with one side designer laminate (OSL) of approved colour and finishing and other side white balancing with density of 850 Kg/cu.m complete all as specified and directed.

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs complete all as specified and directed.

S&F Piano/continuous hinge of size 19 mm stainless steel complete all as specified and directed.

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions all as specified and directed.

M&L Excavation in post hole each n. exc 0.5 cu.m, getting out complete all are specified and directed.

M&L for cement concrete in post holes of type- B2,1:2:4 complete all are specified and directed.

M&L Steel work in tubular trusses, post, purlins & rafters including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 GRADE ST - 240 complete all as specified and directed.

M&L preparation of steel or iron surfaces and apply two coats of synthetic enamel paint over a coats of red oxide complete all as specified and directed.

M&L prepainted galvalume aluminum zinc coating GI based semi corrugated / profile steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws/L-type or J-type or cranked hook bolts in lieu screw as per manufacturar instruction complete all as specified and directed.

S&F Plates (plain or chequered ) channels, square cut or notched (ordinary and counter sunk ) and welds complete all specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand ), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and directede.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. any type complete all as specified and as directed.

Taking down unservesiable sub main wiring with conduits/battens etc complete all as specified and as directed.

Taking down unservesiable MCCB DBs, MCB DBs including MCCBs/TPN/SPN/SP etc complete all as specified and as directed.

M&L for point wiring with single core PVC insulated but unsheathed 1.5 Sqmm FRLS multistranded copper conductor cable 1100 volts grade IS-694 marked drawn in and including rigid non metallic PVC concealed conduit, medium grade not less than 20 mm dia ISI marked with all conduit fittings and fixing accessories including modular metal flush box with modular plate for mounting switches, sockets, fan regulators, etc and earth wire singlle core PVC insulated but unsheathed multistrand copper conductor cable 1100 volts grade IS-694 marked 1.5 Sqmm FRLS cable as continuous earth wire connecting to common earth dolly in concealed wiring system including making good the disturbed surface of wall complete all as specified and directed for the following :-

One light point controlled by one switch one way complete all as specified and directed.

One ceiling fan/exhaust fan point controlled by one switch complete all as specified and directed.

One socket outlet 5 Amp controlled by one switch on independent board complete all as specified and directed.

One 3 pin 5Amps socket out let point on the same board controlled by one switch complete all as specified and directed.

All as per Srl item No 137 here-in-before but for one power point 6 pin 15 Amps socket out let with 2.5 Sq mm stranded copper conductor cable PVC insulated including earth wire 2.5 Sq mm copper conductor cable connected to earth dolly complete, all as specified and directed.

Supply and fixing in replacement of ceiling rose, surface type, 65mm x 50mm, 2 to 3 terminal complete all as specified and as directed.

Supply and fixing white finished single mounting modular plates sutable for modular accessories of following sizes:-

SuItable for 2 modules complete all as specified and directed.

SuItable for 3 modules complete all as specified and directed.

SuItable for 8 modules complete all as specified and directed.

Supply and fixing of modular switch 1 way 6 Amps one module complete all as specified and directed.

Supply and fixing in replacement of modular socket 6 Amps 2/3 Pin combined 02 module complete, all as specified and directed.

Supply and fixing of modular switch one way 16 Amps, one module complete, all as specified and as directed.

Supply and fixing of socket modular type 6 amp/16 amps, 2/3 pin combined 02 Module complete all as specified and as directed.

Supply and fixing Modular Electronic stepped type regulator 100 watt, 2 module complete all as specified and directed.

Supply and fixing for lamp holder, PVC/poleycarbonate type, insulated body with back plate of batten fitting complete all as specified and as directed.

Supply and fixing of Indoor decorative LED battens- integrated Box type 20 watt 4 feet white fixture with extruded aluminium body, suitable for LED tube 20 watt , bipin holder, connector block, LED rod 20 watt etc complete with all accessories internally are wired and including connecting up with twin core copper conductor cable complete all as specified and directed.

Supply and fixing for LED bulb 10 watt of CFL 11/15 watt fixed in pendent holder/bulk head fitting complete all as specified and directed.

Supply and fixing in repalcement of vertical type load line distribution board, double door ,4 way , IP 43 IK08 AC, 3 phase, 415 volts, TPN bus bar and earth bar & din rail complete all as specified and as directed .

Supply and fixing for MCCB, 4 pole 40 A, 16KA, 415Volts complete all as specified and directed .

Supply and fixing in replacement of MCB, SP, 6-32A ,10KA complete all as specified and directed.

Supply and fixing for sub main wiring with 2 run of single core PVC insulated unsheathed FRLSH cable of size 2.5 Sqmm multistranded copper conductor 1100 V grade IS-694 drawing into and including rigid non metallic PVC conduit, medium grade ISI marked (not less than 20 mm) with all conduit fittings & fixing accessories for concealed in wall/ ceiling or surface incl the one run of size 2.5 Sqmm earth continuity conductor of similar type of cable complete all as specified and directed. Note- The 2 runs of single core cable and cified earth continuity conductor and one run relevent conduit with fitting acessories will be measured as one run unit.

Supply & Laying XLPE insulated screened bedded galvanied steel strip or wire armoured electric power cable ( heavy duty) with aluminium conductor 1100 V grade cross sectional area 16 sq mm 4 core complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 meter in depth for laying of cable, pipes and for getting out complete all as specified and as directed .

Returning, filling in soft/loose soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed.

Removing excavated surplus soil to a distance not exceeding 50 meter and depositing where directed at a level not exc. 1.5 meter above the starting point complete all as specified and as directed.

M&L for laying,spreading dry fine river sand in trenches as cushioning for ptotection of cable, 8 cm before laying of cable and 15 cm after laying of cable complete all as specified and as directed. Note:- For payment punned depth will be measured.

Supply and laying unreinforced precast concrete cable cover, class HVP,type-1 with peak,size 250mmx150mmx40mm laid flat adjacent and abutting to each other across the length of cable laid dry complete all as specified and as directed.

M&L Earthing complete with galvanised steel earth plate electrode 600 mm x 600 cm x 6.00 mm thick buried directly in ground (earth plate not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to and including GI earth lead of GI wire 4.00 mmthick by means of steel bolts, nuts, check nuts and washers test points by GI pipe 40X8 mm 10 cm long,PCC 1:2:4 type B-1 in pit, angle iron 25x25x3mm frame work with precast RCC 1:2:4type B-1 cover reinforced with 8 mm dia TMT bars @ 150 mm C /C both ways and 12 mm dia MS fabricated handle, mediam grade GI water pipe 20 mm bore with funnel, wire mesh and light gradeGI protection pipe 40 mm bore upto 5 M length for drawing in earth lead , salt charcol etc including excavation in earth work in any type of soil, removal of surplus soil to a distance not exceeding 50 m complete , all as shown in Electric plate No 3 of MES schedule 2009 Part-I and connected complete including testing on completion all as specified and directed.

S&F Water heater storage,electric capacity 25 Ltrs BEE 5 Star rated with complete accessories such as safety valve, thermostate, NRV type complete all as specified and directed.

S&F Exhaust fan AC single phase 230/240 V of size 300 mm sweep with louvers complete all as specified and directed.

Taking down ceiling fans of any sweep and any size including cable connections and disconnecting of fan blades and removing the fan with blades and deposit in MES store yard complete all as specified and directed.

S&F BLDC Ceiling fans AC single phase complete with electronic regulator and accessories 230 v 1200mm sweep, BEE 5 star rated complete all as specified and directed.

Please Enable Macros to View BoQ information