Providing Multi Villages Piped Water Supply Scheme for Haroli Constituency in Haroli Block Distt. Una (H.P.) Phase-2nd (UNDER JAL JEEVAN MISSION) in single package on Turn key job

Amount

Schedule -B2 Providing, laying , jointing and testing of rising mains.

Excavation in foundation and trenches etc.(in pipes and pits) in all kinds of soils such as pick work, jumper work, blasting in soft / hard rock, chiselling/wedging out of rock/where blasting prohibited) saturated soil stacking the excavated earth within all leads and lifts clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinth sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer –in-charge.

Providing, Laying, jointing and testing in trenches (to level or grade) GMS pipes of following dia and class conforming to IS 1239-1990 (Part-I) (latest upto date ammendments) of grade and wall thickness as specified below, suitable to withstand required hydraulic test pressure in randum length 5 m-7 m with plain ends and jointed with MS Flanges conforming to IS:6392-1971 (latest upto date amendments) and welding of flanges as per IS: 816-1969 with electrodes as per IS:814-1991 including required number and size of MS nuts and bolts as per IS 1369-1967 and compressed asbestos fibre jointing gaskets sheet not less than 3.00mm in thickness as per IS:2712-1998. & butt welded joints. The welding of flanges to be done on both faces in two layers on outer face & one layer on inner face to make the joints leak proof and to the entire satisfaction of the Engineer-in-Charge. The laying of Pipes conform to IS 5822-1994 and as per CPHEEO manual and will include all operations such as cutting, welding and jointing including flushing, cleaning and hydraulic testing complete in all respects to the entire satisfaction of Engineer-in-Charge including entire carriage of materials upto all leads and lifts. (Earth work in trenches, welding of flanges/butt welding will be measured and paid for seperately)

50mm Dia (MG)

65mm Dia (MG)

80mm Dia (MG)

100mm Dia (MG)

Providing and welding M.S. flanges @ 5% of joints, conforming to following tables as per IS 6392-1971 (Latest with upto date amendments) with plain end GMS/MSERW pipe in requsite number of layers on both faces to make the joint leak proof (The cost of providing and laying of MSERW pipes to be measured and paid for seprately). The welding of flanges should conform to IS:816-1969 with electrodes as per IS: 814-1991 and required number of nuts and bolts conforming to IS 1364. including cost of gasket sheet nuts & bolts. The thickness of gasket sheet not less then 3.00mm conforming to IS 2712-1998. The work shall be done to the entire satifaction of engineer in charge with in all leads and lifts.

50 mm Dia Table-5 (5% of total joints)

65 mm Dia Table-17 (5% of total joints)

80 mm Dia Table-5 (5% of total joints)

100 mm Dia Table-17 (5% of total joints)

100 mm Dia Table-5 (5% of total joints)

Providing circumferential butt welded joints by electrical arc welding to GMS pipe, welded in requisite number of weld runs so as to achieve the minimum effective throat thickness of weld conforming to IS 816-1969 specifications, by using welding electrodes of 2.5mm to 6.3mm of Advani Oerilikon (Adore)-CITOJET/ES/ESAB make,conforming to IS 814-1991, include Die pentration test,at site of work complete in all respects, including manual/mechanical handling of pipes in all leads and lifts to the entire satisfaction of Engineer-in-Charge.

50 mm Dia

65 mm Dia

80 mm Dia

100 mm Dia

Providing and fixing double flanged Cast Steel Non Return Valve, following class of Leader/ Kirloskar make for rising main and capable of with standing 21 Kg/cm^2 normal seat pressure conforming to BS:1868/API-600 or latest ammendments.

50mm dia Class ASA- 150

65mm dia Class ASA- 150

80mm dia Class ASA- 150

100mm dia Class ASA- 150

Providing and fixing screwed type cast iron air valve of 25 mm dia (single ball type) of Leader/ Kirloskar make confirming to BS : 1452-90 with upto date amendments as per class PN-1.00 to withstand a seat pressure 11.22 Kg/ cm2 in rising main.

Schedule -B2 Supply and errection of Submersible Pumping Machinery alongwith allied accessories

S/E of Submersible Pumping Machinery for T/Well at Rora Supply of submersible pumping set of reputed make such as KSB/ Calama / BS/ Worthigton / Sabar/ Seerex /Johnston / Amrut/ lubi/ Hindustan,Groundfos confirming to latest relevent BIS . The pump should be fitted with free fine impellers of suitable alloys as per BIS ; 5659-1978 with upto date amendments, suitable for raw / clear water having greased packed bearing and shell with wound stator on motor side and with shaft protection on pump side ensuring better life for shaft conforming to BIS specifications. The pump shall be directly coupled to submersible motor of same as that of offered submersible pump make confirming to BIS ;9283-1979 with upto date amendments, totally dust and water proof for submersible pump, duly isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed, lubricated bearing and provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear tear.It should also be fitted with a device to make up expantion of water with heating of motor. The pumpset should include water level guard i/c cable ,errection clamps, cable clips and depth gauge etc. and suitable for opertion on data given below. a Pumps :- Specifications i) Make ii) Model iii) No. of stages iv) Manufacter's certificate to be attached Performance i) Discharge ii) Head iii) Efficiency of Pump a) Duty Head b) (+) 10% Duty Head. c) (-) 15% Duty Head d) Performance curve to be attached b) Motors; Specification i) Make ii) Model iii) B.H.P iv) Speed v) Insulation

Discharge =( Q) 1.32 LPS

Total Head =( H) 108.12 Mts.

a) SWL in Tubewell = 27.43 Mtr. bgl.

c) R.L. point of discharge =415.30Mtr.

d) Seasonal fluctuation + draught condition + bowl assembly. 9.00 Mtrs.

e) Drawdown in Tubewell =14Mtrs.

f) R.L of lowest point of pumpset installation =323.63 Mtrs.

g) Static Column lift =73 Mtrs.

Rising main. Column Pipe.

Length 590 Mtrs. Length 50.43 Mtr.

Dia meter. 50 mm Dia 50 mm

Class GMS Class GMS. (M)

Pumping hours 16 hours

Altitude of installations above M.S.L. _374_mtr.

Characteristic of water.

a) Temperature _____20__ Deg Cel.

b) Turbidity ________JTU.

c) Allkanity. ___________mg/ l Ca Co3

d) Size of solids ____________mm

e) others

Depth of T/well mtr.

Dia of T/ well assembly 200 mm.

Length of assembly pipe.

Dia of housing pipe 300 mm.

Length of housing pipe

OPERATING CONDITIONS.

Type of Current :- A.C.Three Phase.

Frequency:- 50 Cycles /Sec.

Rated Voltage 415 +/- 15 % Volts.

System of earthing: Double Loop earthing as per BIS 3843-1987 Latest.

Speed of Revolution ____________ RPM 2900

MOTOR.

Ref. to BIS code BIS 9283-1979 with upto date amendments.

Type of enclosure of motor: As per BIS ; 4691-1985 ( latest )

Mechanical out put in H.P.

Class of insulation :Class B

The motor should be able to withstand initial current of 2.50 times the rated current for two minutes without suffering damages of permanent deformations.

Ref. to BIS code ; BIS ; 5659-1978 with upto date amendments.

Drive Type: Electric driven.

Operating Range: -15 % to+10 % of Total head at duty point.

Deliver size of Pump : ________( To be quoted by tenderer.)

Providing ICTP Main Switch with HRC fuses of L&T/ Havells make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments. ICTP Switch: i) Make : ii) Type : iii) Capacity : 32 Amp.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. . Panel /Switch Board. i) Drawing.ii) layout Plan.

MCB of kilburn / L&T/ Havells make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. MCB 1) Make. ii) Type iii) Range. iv) Capacity 32 Amp.

ii) ELCB of recommended make L&T / Havells as per IS ; 2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELCB 1) Make. ii) Type iii) Range. iv) Capacity upto 63 Amp.

iii) The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage,reverse phasing,overloading and phase voltage difference as per IS; 3842 ( Latest Edition ) Volatage Monitor Relay i) Make ii ) Type iii) Range 0-500

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments including. Bus Bar Chamber i) Type ii) Make iii) Rating

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments. 3 phase indicators

e) Capacitor of BHEL / GEC / L&T / Mecheil make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. Capacitor i) Type ii) Make iii) Range 2 KVAR

Providing Direct on line star delta starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments. Starter i) Type ii) Make Single phase preventor i) Type ii) Make

Providing and fixing double flanged Cast Iron Sliuce valve of Leader / Kirloskar/Kartar/LP brand make for the Column pipe of pump and capable of withstanding the normal seat pressure and as per IS 780-1992 with latest ammendments Class PN 1.00 For Column Pipe 65mm dia Sluice valve i) Make ii) Class PN 1.00 iii) Material cast iron

Providing and fixing double flanged Cast Iron Reflux valve of Leader / Kirloskar/Kartar/LP brand make having by pass arrangement on the rising main of pump and capable of withstanding the normal seat pressure and as per IS 5312-1984 P-I with latest ammendments 65 mm dia Reflex valve i) Make ii) Class PN 1.60 iii) Material cast iron

Providing and fixing pressure gauge of Prega / Precision / Fiebig make complete with all accessories such as stop cock, copper tubing as per IS ; 3624-1987 with upto date amendements Pressure Gauge i) Make

Supply of PVC jointless,flat water proof cable with copper conductor as per BIS 694-1998 latest with upto date ammendments of Havelles/Finolex make suitable for the pumpsets offered from MCB to motor including all other electrical equipments / accessories such as thimble, flexible pipe,solder, nuts and bolts, cable glands, clips etc, laid in pipes or trenches under floor.The type, size and make shall be subject to approval of HPSEB authorities. Submersible cable i) Finolex/ Havells make ii) Size 2.5mm2 (iii) Core=3

Providing and Lowering of GMS Column pipe for assembly 100 mm dia including MS flanges' of Table 17 as per IS : 6392-1971 with upto date amendments, rubber / asbestos gasket of min.3 mm thickness as per IS 2712-1979 and required numbers of nuts and bolts as per IS ;1364-1983 .The Column pipe shall be as per relevent IS Code and to withstand 1.50 times total head stipulated under item No.5 . The Column pipe should be extended upto 5 mtr. beyond the outer wall of the pump house in the direction of Rising main .The Column pipe should be properly jointed with the Rising main including all necessary accessories like increaser / reducer, flanges, bends etc, including supporting clamps (2 Nos.) at the top of T/well assembly, and as per the direction of Engineer - in - Charge. Column pipe i) Size 65 mm dia ii) Class (M) iii) Length

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor. Armoured Power Cable A) Supply side from meter of HPSEB to Bus Bar and Switch i) Size 2.50 mm2 B) Supply motor side i) Size 2.50 mm2 ii) Make iii) Type iv) Capacity v) core

Providing and fixing double loop earthing with GI plate of 600x600x6.3 mm thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer - in - Charge. GI 8SWG up to 15 HP

S/E of Submersible Pumping Machinery for T/Well at Dharampur Supply of submersible pumping set of reputed make such as KSB/ Calama / BS/ Worthigton / Sabar/ Seerex /Johnston / Amrut/ lubi/ Hindustan,Groundfos confirming to latest relevent BIS . The pump should be fitted with free fine impellers of suitable alloys as per BIS ; 5659-1978 with upto date amendments, suitable for raw / clear water having greased packed bearing and shell with wound stator on motor side and with shaft protection on pump side ensuring better life for shaft conforming to BIS specifications. The pump shall be directly coupled to submersible motor of same as that of offered submersible pump make confirming to BIS ;9283-1979 with upto date amendments, totally dust and water proof for submersible pump, duly isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed, lubricated bearing and provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear tear.It should also be fitted with a device to make up expantion of water with heating of motor. The pumpset should include water level guard i/c cable ,errection clamps, cable clips and depth gauge etc. and suitable for opertion on data given below. a Pumps :- Specifications i) Make ii) Model iii) No. of stages iv) Manufacter's certificate to be attached Performance i) Discharge ii) Head iii) Efficiency of Pump a) Duty Head b) (+) 10% Duty Head. c) (-) 15% Duty Head d) Performance curve to be attached b) Motors; Specification i) Make ii) Model iii) B.H.P iv) Speed v) Insulation

Discharge =( Q) 2.18 LPS

Total Head = ( H) 169.55 Mts.

a) SWL in Tubewell =45.70 Mtr. bgl.

c) R.L. point of discharge = 446.00 Mtr.

d) Seasonal fluctuation + draught condition + bowl assembly. 9.00 Mtrs.

e) Drawdown in Tubewell =18.30Mtrs.

f) R.L of lowest point of pumpset installation =296.20 Mtrs.

g) Static Column lift =73.00 Mtrs.

Rising main. Column Pipe.

Length 1050 Mtrs. Length 65.45 Mtr.

Dia meter.65 mm Dia 65 mm

Class GMS Class GMS. (M)

Pumping hours 16 hours

Altitude of installations above M.S.L. 361_mtr.

Characteristic of water.

a) Temperature ___20_ Deg Cel.

b) Turbidity ________JTU.

c) Allkanity. ___________mg/ l Ca Co3

d) Size of solids ____________mm

e) others

Depth of T/well mtr.

Dia of T/ well assembly 200 mm.

Length of assembly pipe.

Dia of housing pipe 300 mm.

Length of housing pipe

OPERATING CONDITIONS.

Type of Current :- A.C.Three Phase.

Frequency:- 50 Cycles /Sec.

Rated Voltage 415 +/- 15 % Volts.

System of earthing: Double Loop earthing as per BIS 3843-1987 Latest.

Speed of Revolution ____________ RPM 2900

MOTOR.

Ref. to BIS code BIS 9283-1979 with upto date amendments.

Type of enclosure of motor: As per BIS ; 4691-1985 ( latest )

Mechanical out put in H.P.

Class of insulation :Class B

The motor should be able to withstand initial current of 2.50 times the rated current for two minutes without suffering damages of permanent deformations.

Ref. to BIS code ; BIS ; 5659-1978 with upto date amendments.

Drive Type: Electric driven.

Operating Range: -15 % to+10 % of Total head at duty point.

Deliver size of Pump : ________( To be quoted by tenderer.)

Providing ICTP Main Switch with HRC fuses of L&T/ Havells make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments. ICTP Switch: i) Make : ii) Type : iii) Capacity : 32 Amp.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. . Panel /Switch Board. i) Drawing.ii) layout Plan.

MCB of kilburn / L&T/ Havells make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. MCB 1) Make. ii) Type iii) Range. iv) Capacity 32 Amp.

ii) ELCB of recommended make L&T / Havells as per IS ; 2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELCB 1) Make. ii) Type iii) Range. 63 Amp. iv) Capacity 63 Amp.

iii) The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage,reverse phasing,overloading and phase voltage difference as per IS; 3842 ( Latest Edition ) Volatage Monitor Relay i) Make ii ) Type iii) Range 0-500

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments including. Bus Bar Chamber i) Type ii) Make iii) Rating

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments. 3 phase indicators

e) Capacitor of BHEL / GEC / L&T / Mecheil make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. Capacitor i) Type ii) Make iii) Range 5 KVAR

Providing air break type star delta starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments. Starter i) Type ii) Make Single phase preventor i) Type ii) Make

Providing and fixing double flanged Cast steel Sluice valve of Leader / Kirloskar/ Kartar/LP brand make of 80 mm dia for the Column pipe of pump and capable of withstanding the normal seat pressure and as per BIS 1414/API 600 with latest ammendments Class ASA 150 For Column Pipe 80 mm dia Sluice valve i) Make ii) Class ASA 150 iii) Material cast steel

Providing and fixing pressure gauge of Prega / Precision / Fiebig make complete with all accessories such as stop cock, copper tubing as per IS ; 3624-1987 with upto date amendements Pressure Gauge i) Make

Supply of PVC jointless,flat water proof cable with copper conductor as per BIS 694-1998 latest with upto date ammendments of Havelles/Finolex make suitable for the pumpsets offered from MCB to motor including all other electrical equipments / accessories such as thimble, flexible pipe,solder, nuts and bolts, cable glands, clips etc, laid in pipes or trenches under floor.The type, size and make shall be subject to approval of HPSEB authorities. Submersible cable i) Finolex/ Havells make ii) Size 2.5mm2 (iii) Core=3

Providing and Lowering of GMS Column pipe for assembly 80 mm dia including MS flanges' of Table 17 as per IS : 6392-1971 with upto date amendments, rubber / asbestos gasket of min.3 mm thickness as per IS 2712-1979 and required numbers of nuts and bolts as per IS ;1364-1983 .The Column pipe shall be as per relevent IS Code and to withstand 1.50 times total head stipulated under item No.5 . The Column pipe should be extended upto 5 mtr. beyond the outer wall of the pump house in the direction of Rising main .The Column pipe should be properly jointed with the Rising main including all necessary accessories like increaser / reducer, flanges, bends etc, including supporting clamps (2 Nos.) at the top of T/well assembly, and as per the direction of Engineer - in - Charge. Column pipe i) Size 80 mm dia ii) Class (M) iii) Length

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor. Armoured Power Cable A) Supply side from meter of HPSEB to Bus Bar and Switch i) Size 2.5 mm2 B) Supply motor side 2.5mm 2ii) Make iii) Type iv) Capacity v) core

Providing and fixing double loop earthing with GI plate of 600x600x6.3 mm thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer - in - Charge. i) up to 15 HP=8SWG

S/E of Submersible Pumping Machinery for T/well at Badhera Supply of submersible pumping set of reputed make such as KSB/ Calama / BS/ Worthigton / Sabar/ Seerex /Johnston / Amrut/ lubi/ Hindustan,Groundfos confirming to latest relevent BIS . The pump should be fitted with free fine impellers of suitable alloys as per BIS ; 5659-1978 with upto date amendments, suitable for raw / clear water having greased packed bearing and shell with wound stator on motor side and with shaft protection on pump side ensuring better life for shaft conforming to BIS specifications. The pump shall be directly coupled to submersible motor of same as that of offered submersible pump make confirming to BIS ;9283-1979 with upto date amendments, totally dust and water proof for submersible pump, duly isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed, lubricated bearing and provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear tear.It should also be fitted with a device to make up expantion of water with heating of motor. The pumpset should include water level guard i/c cable ,errection clamps, cable clips and depth gauge etc. and suitable for opertion on data given below. a Pumps :- Specifications i) Make ii) Model iii) No. of stages iv) Manufacter's certificate to be attached Performance i) Discharge ii) Head iii) Efficiency of Pump a) Duty Head b) (+) 10% Duty Head. c) (-) 15% Duty Head d) Performance curve to be attached b) Motors; Specification i) Make ii) Model iii) B.H.P iv) Speed v) Insulation

Discharge =( Q) 10.47 LPS

Total Head = ( H) 77.46 Mts.

a) SWL in Tubewell =30.48 Mtr. bgl.

c) R.L. point of discharge = 334.50 Mtr.

d) Seasonal fluctuation + draught condition + bowl assembly. 9.00 Mtrs.

e) Drawdown in Tubewell =10.67Mtrs.

f) R.L of lowest point of pumpset installation =282.85 Mtrs.

g) Static Column lift =3.00Mtrs.

Rising main. Column Pipe.

Length 20 Mtrs. Length 50.15 Mtr.

Dia meter.65 mm Dia 65 mm

Class GMS Class GMS. (M)

Pumping hours 16 Hours

Altitude of installations above M.S.L. _350_________mtr.

Characteristic of water.

a) Temperature ___20____ Deg Cel.

b) Turbidity ________JTU.

c) Allkanity. ___________mg/ l Ca Co3

d) Size of solids ____________mm

e) others

Depth of T/well mtr.

Dia of T/ well assembly 200 mm.

Length of assembly pipe.

Dia of housing pipe 300 mm.

Length of housing pipe

OPERATING CONDITIONS.

Type of Current :- A.C.Three Phase.

Frequency:- 50 Cycles /Sec.

Rated Voltage 415 +/- 15 % Volts.

System of earthing: Double Loop earthing as per BIS 3843-1987 Latest.

Speed of Revolution ____________ RPM 2900

MOTOR.

Ref. to BIS code BIS 9283-1979 with upto date amendments.

Type of enclosure of motor: As per BIS ; 4691-1985 ( latest )

Mechanical out put in H.P.

Class of insulation :Class B

The motor should be able to withstand initial current of 2.50 times the rated current for two minutes without suffering damages of permanent deformations.

Ref. to BIS code ; BIS ; 5659-1978 with upto date amendments.

Drive Type: Electric driven.

Operating Range: -15 % to+10 % of Total head at duty point.

Deliver size of Pump : ________( To be quoted by tenderer.)

Providing ICTP Main Switch with HRC fuses of L&T/ Havells make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments. ICTP Switch: i) Make : ii) Type : iii) Capacity : 63 Amp.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. . Panel /Switch Board. i) Drawing.ii) layout Plan.

MCB of kilburn / L&T/ Havells make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. MCB 1) Make. ii) Type iii) Range. iv) Capacity 63 Amp.

ii) ELCB of recommended make L&T/Havells as per IS ; 2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELCB 1) Make. ii) Type iii) Range. iv) Capacity 63 Amp.

iii) The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage,reverse phasing,overloading and phase voltage difference as per IS; 3842 ( Latest Edition ) Volatage Monitor Relay i) Make ii ) Type iii) Range 0-500

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments including. Bus Bar Chamber i) Type ii) Make iii) Rating

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments. 3 phase indicators

e) Capacitor of BHEL / L&T make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. Capacitor i) Type ii) Make iii) Range 5 KVAR

Providing suitable oil immersed star starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments. Starter i) Type ii) Make Single phase preventor i) Type ii) Make

Providing and fixing double flanged Cast Iron/Ductile iron Sliuce valve of Leader/ Kirloskar/Kartar/LP brand make for the Column pipe of pump and capable of withstanding the normal seat pressure and as per IS 780-1992 with latest ammendments Class PN 1.00 For Column Pipe 100 mm dia Sluice valve i) Make ii) Class PN 1.00 iii) Material cast iron / DI

Providing and fixing pressure gauge of Prega / Precision / Fiebig make complete with all accessories such as stop cock, copper tubing as per IS ; 3624-1987 with upto date amendements Pressure Gauge i) Make

Supply of PVC jointless,flat water proof cable with copper conductor as per BIS 694-1998 latest with upto date ammendments of Havelles/Finolex make suitable for the pumpsets offered from MCB to motor including all other electrical equipments / accessories such as thimble, flexible pipe,solder, nuts and bolts, cable glands, clips etc, laid in pipes or trenches under floor.The type, size and make shall be subject to approval of HPSEB authorities. Submersible cable i) Finolex/ Havells make ii) Size 4 mm2 (iii) Core=3

Providing and Lowering of GMS Column pipe for assembly 100 mm dia including MS flanges' of Table 17 as per IS : 6392-1971 with upto date amendments, rubber / asbestos gasket of min.3 mm thickness as per IS 2712-1979 and required numbers of nuts and bolts as per IS ;1364-1983 .The Column pipe shall be as per relevent IS Code and to withstand 1.50 times total head stipulated under item No.5 . The Column pipe should be extended upto 5 mtr. beyond the outer wall of the pump house in the direction of Rising main .The Column pipe should be properly jointed with the Rising main including all necessary accessories like increaser / reducer, flanges, bends etc, including supporting clamps (2 Nos.) at the top of T/well assembly, and as per the direction of Engineer - in - Charge. Column pipe i) Size 100 mm dia ii) Class (M) iii) Length

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor. Armoured Power Cable A) Supply side from meter of HPSEB to Bus Bar and Switch i) Size 6 mm2 A) Supply motor side size 4mm2 ii) Make iii) Type iv) Capacity v) core

Providing and fixing double loop earthing with GI plate of 600x600x6.3mm thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt,25x5mm strip as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer-in-Charge. i) GI 4SWG 20HP to 30HP

S/E of Submersible Pumping Machinery for T/well at Panjawar Supply of submersible pumping set of reputed make such as KSB/ Calama / BS/ Worthigton / Sabar/ Seerex /Johnston / Amrut/ lubi/ Hindustan,Groundfos confirming to latest relevent BIS . The pump should be fitted with free fine impellers of suitable alloys as per BIS ; 5659-1978 with upto date amendments, suitable for raw / clear water having greased packed bearing and shell with wound stator on motor side and with shaft protection on pump side ensuring better life for shaft conforming to BIS specifications. The pump shall be directly coupled to submersible motor of same as that of offered submersible pump make confirming to BIS ;9283-1979 with upto date amendments, totally dust and water proof for submersible pump, duly isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed, lubricated bearing and provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear tear.It should also be fitted with a device to make up expantion of water with heating of motor. The pumpset should include water level guard i/c cable ,errection clamps, cable clips and depth gauge etc. and suitable for opertion on data given below. a Pumps :- Specifications i) Make ii) Model iii) No. of stages iv) Manufacter's certificate to be attached Performance i) Discharge ii) Head iii) Efficiency of Pump a) Duty Head b) (+) 10% Duty Head. c) (-) 15% Duty Head d) Performance curve to be attached b) Motors; Specification i) Make ii) Model iii) B.H.P iv) Speed v) Insulation

Discharge (Q) = 11.30 LPS.

Total Head (H) = 64.18 mtrs.

a)LWL In clear water tank = 18.29 mtr

b) R.L. of shaft = 376.55Mtrs.

c) R.L. of discharge Point. = 329.78 mtrs.

d) Suction lift. +tive mtrs.

e)Discharge Head = 0.00 mtrs.

f) Static Head = 3.00 mtrs.

Rising main.

Length = 20.00 mtrs.

Diameter = 100 mm. dia

Class GMS Tube (MG)

Pumping hours. 16.00 hours.

Altitude of installations above M.S.L 350 mtrs.

Characteristic of Water

a)Temperature _____20___Deg.Col.

b)Turbidity ________ JTU

c) Alloanity _________ mg/1 ca Co3

d)Size of solids __________ mm

e) Others.

(a) Pumps: Specifications:

i)Make

ii)Model.

iii)No.of stages:-

iv)Manufacturers

certificate to be attached.

Performance

i)Discharge:-

ii)Total Head:-

iii)B.H.P.

iv)Efficiency:

vi)Performance Curve to be attached.

b)Motors: Specifications.

i)Make

ii)Model

iii)Rating

iv)Speed.

v)Insulation.

(C) Coupling:

(d) Base Plate.

Providing ICTP Main Switch with HRC fuses of L&T/ Havells/ Standard / Kilburn / Siemens make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments. ICTP Switch: i) Make : ii) Type : iii) Capacity : 63Amp.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. . Panel /Switch Board. i) Drawing.ii) layout Plan.

OCB of kilburn / L&T/ Havells / Standard make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. OCB 1) Make. ii) Type iii) Range. iv) Capacity. 63 Amp.

ii) ELCB of recommended make L&T Havells / Standard / Kilburn as per IS ; 2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELR 1) Make. ii) Type iii) Range. 63 Amp. iv) Capacity.

iii) The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage,reverse phasing,overloading and phase voltage difference as per IS; 3842 ( Latest Edition ) Volatage Monitor Relay i) Make ii ) Type iii) Range

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments including. Bus Bar Chamber i) Type ii) Make iii) Rating

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments. 3 phase indicators

e) Capacitor of BHEL / L&T make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. Capacitor i) Type ii) Make iii) Range 5 KVAR

Providing suitable oil immersed star starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments. Starter i) Type ii) Make Single phase preventor i) Type ii) Make

Providing and fixing double flanged Cast Iron/Ductile iron Sliuce valve of Leader/ Kirloskar/Kartar/LP brand make for the Column pipe of pump and capable of withstanding the normal seat pressure and as per IS 780-1992 with latest ammendments Class PN 1.00 For Column Pipe 100 mm dia Sluice valve i) Make ii) Class PN 1.00 iii) Material cast iron / DI

Providing and fixing double flanged Cast steel Sluice valve of Leader / Kirloskar/ Kartar/LP brand make of 150 mm dia for the delivery line of pump and capable of with standing normal Seat Pressure as per BIS 1414/API 600 with upto date ammendments. For delivery pipe of pump. 150 mm Sluice Valve i)Make ii) Class ASA 300 iii)Test working head. iv) Material:-Cast Steel

Providing and fixing pressure gauge of Prega / Precision / Fiebig make complete with all accessories such as stop cock, copper tubing as per IS ; 3624-1987 with upto date amendements Pressure Gauge i) Make

Supply of PVC jointless,flat water proof cable with copper conductor as per BIS 694-1998 latest with upto date ammendments of Havelles/Finolex make suitable for the pumpsets offered from MCB to motor including all other electrical equipments / accessories such as thimble, flexible pipe,solder, nuts and bolts, cable glands, clips etc, laid in pipes or trenches under floor.The type, size and make shall be subject to approval of HPSEB authorities. Submersible cable i) Finolex/ Havells make ii) Size 4 mm2 (iii) Core=3

Providing and Lowering of GMS Column pipe for assembly 100 mm dia including MS flanges' of Table 17 as per IS : 6392-1971 with upto date amendments, rubber / asbestos gasket of min.3 mm thickness as per IS 2712-1979 and required numbers of nuts and bolts as per IS ;1364-1983 .The Column pipe shall be as per relevent IS Code and to withstand 1.50 times total head stipulated under item No.5 . The Column pipe should be extended upto 5 mtr. beyond the outer wall of the pump house in the direction of Rising main .The Column pipe should be properly jointed with the Rising main including all necessary accessories like increaser / reducer, flanges, bends etc, including supporting clamps (2 Nos.) at the top of T/well assembly, and as per the direction of Engineer - in - Charge. Column pipe i) Size 100 mm dia ii) Class (M) iii) Length

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor. Armoured Power Cable A) Supply side from meter of HPSEB to Bus Bar and Switch i) Size 6 mm2 A) Supply motor side size 4mm2 ii) Make iii) Type iv) Capacity v) core

Providing and fixing double loop earthing with GI plate of 600x600x6.3mm thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt,25x5mm strip as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer-in-Charge. i) GI 4SWG 20HP to 30HP

Centrifugal Pumping Machinery alongwith allied accessories for Kangar (R/main 2) Providing horizontal spindle, horizontal / radial split casing /end suction ( back pull out arrange-ment) Single /double /multi stage of Kirloskar / KSB Crupton KSB/Calama/BS/ Groundfos/ Hindustan/ Lubbi make as per BIS IS 1520-1980 with upto date ammendments read with IS: 9137-1978 or latest edition suitable for lifting water for under mentioned characteristic with Bronze impellers / priming funnels, casing ring and shaft sleeves of Bronze shaft of stainless steel with cast iron casing, coupled directly through a flexible coupling on a common cast iron / cast steel base plate (base plate to be framed from the manufacturers of the pumping unit only) to slipring / Squirrel cage screen protected drip proof induction motor / motors of standard make such as Crompton / NGEF / GEC / Seimens /Jyoti/ Kirloskar BHEL / ABB suitable for operation on 415 (+/-15%) volts. 50 Cycles /Sec. 3 phase AC electric supply of 2900 RPM.The power of electric motor/ motors should be at least +10% in excess of the maximum power required by the pump / pumps in the Operation range of (+10%) and (-15%) of the duty point head. The motor / motors as per IS 325 IS -1978 with upto date amendments read with IS 900 -1972. It should include cost of Bearing. Nuts, Bolts and painting etc. and should meet the following requirements.

Discharge (Q) = 1.80 LPS.

Total Head (H) = 23.63 mtrs.

a)LWL in clear water tank = 351.70 mtr

b) R.L. of shaft = 352.15 Mtrs.

c) R.L. of discharge Point. = 370.15 mtrs.

d) Suction lift. +tive mtrs.

e)Discharge Head = 0.00 mtrs.

f) Static Head = 18.00 mtrs.

Rising main.

Length = 40.00 mtrs.

Diameter = 50 mm. dia

Class GMS Tube (MG)

Pumping hours. 16.00 hours.

Altitude of installations above M.S.L 352 mtrs.

Characteristic of Water

a)Temperature _____20___Deg.Col.

b)Turbidity ________ JTU

c) Alloanity _________ mg/1 ca Co3

d)Size of solids __________ mm

e) Others.

(a) Pumps: Specifications:

i)Make

ii)Model.

iii)No.of stages:-

iv)Manufacturers

certificate to be attached.

Performance

i)Discharge:-

ii)Total Head:-

iii)B.H.P.

iv)Efficiency:

vi)Performance Curve to be attached.

b)Motors: Specifications.

i)Make

ii)Model

iii)Rating

iv)Speed.

v)Insulation.

(C) Coupling:

(d) Base Plate.

Providing ICTP Main Switch with HRC fuses of L&T/ Havells/ Standard / Kilburn / Siemens make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments. ICTP Switch: i) Make : ii) Type : iii) Capacity : 63Amp.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. . Panel /Switch Board. i) Drawing.ii) layout Plan.

MCB of kilburn / L&T/ Havells make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. MCB 1) Make. ii) Type iii) Range. iv) Capacity. 63 Amp.

ii) ELCB of recommended make L&T / Havells as per IS ; 2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELCB 1) Make. ii) Type iii) Range. iv) Capacity. 63 Amp.

iii) The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage,reverse phasing,overloading and phase voltage difference as per IS; 3842 ( Latest Edition ) Volatage Monitor Relay i) Make ii ) Type iii) Range

Power factor meter of standard make as per relevent IS code with upto date ammendments. Power factor meter i) Make ii ) Type iii) Range 0-500

Frequency meter of standard make as per relevent IS code with upto date ammendments. Frequency meter i) Make ii ) Type iii) Range 0-500

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments including. Bus Bar Chamber i) Type ii) Make iii) Rating

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments. 3 phase indicators

Capacitor of Mecheil / BHEL / GEC / L&T make as per IS : 2834-1986 with upto date ammendments , to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered i/c cables as per relevant ISI code ( of Seimens / Clocter / IEC make) from bus bar chamber to capacitor and also including ICTP switches of appropriate range as per IS: 4064-1978 with upto date ammendments, Rating of capacitor will be approved by HPSEB. Capacitor i)Type ii)Make iii)Range.2 KVAR

Providing suitable starter direct on line of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments. Starter i) Type ii) Make Single phase preventor i) Type ii) Make

Providing and fixing double flanged cast steel Sluice valve as per BIS 1414/API 600 with upto date ammendmnent of Kirloskar / Leader/ Kartar/ LP brand make for the suction pipe of 80 mm dia Class ASA 300 for the suction line of pump . Sluice Valve i)Make ii) Class ASA 300 iii)Test working head. iv) Material: Cast Steel

Providing and fixing double flanged Cast Iron Sluice valve of Leader / Kirloskar/ Kartar/LP brand make of 50 mm dia for the delivery line of pump and capable of with standing normal Seat Pressure as per BIS 780-1984(P1) with upto date ammendments. For delivery pipe of pump. 50 mm Sluice Valve i)Make ii) Class PN1.0 iii)Test working head. iv) Material:-Cast Iron

Providing and fixing double flanged swing type cast iron Reflux valves of Leader/ Kirloskar/ Kartar/LP brand make of 50 mm dia Class PN 1.0 for delivery line of pump and capable of with standing the normal seat pressure and as per IS: 780-1984 (P -1) with upto date ammendments. 50 mm dia Reflux Valve i)Make ii) Class PN 1.0 iii)Test working head. iv) Material:-Cast Iron

Providing and fixing double flanged swing type cast steel Reflux valves of Leader / Kirloskar/ Kartar/ LP brand make of 50 mm dia Class PN 1.0 having by pass arrangement for the Rising main of the Pump and capable of with standing the normal seat pressure and as per IS: 780-1984 (P-1) with upto date ammendments.Reflux Valve i)Make ii) Class PN1.0 iii)Test working head. iv) Material:-Cast Iron

Providing and fixing 25 mm dia steel circular dial pressure gauge of Precision / Fiebig make complete with all accessories such as stop cock,Copper tubing etc.as per IS: 3624-1987 with upto date ammendments. Pressure Gauge i) Make ii Range

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and Fixing double flanged GMS piping work ( Layout to be approved by Engineer-in-Charge). for suction and delivery pipes suitable to pumps offered and common header as per the rising main respectively complete with all specials such as bends,Tees, Reducers / Inceasers with companion flanges matching with the relevant specifications of the accessories as indicated in the Drawing including rubber / asbestos gasket of 3 mm thickness as per IS : 2712-1972 and required number of Nuts and Bolts as per 1364-1983.-the pipes shall be as per relevent IS code and to withstand 1.50 times total head stipulated under item No.30.The size of various components to be as under:-

i) Suction Pipe 40 mm dia.

ii) Delivery Pipe 50 mm dia.

iii) Common Header 50 mm dia. and will extend upto 5 metres from the outer wall of the pump house in the direction of Rising main of 50 mm dia to be joined.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor. Armoured Power Cable A) Motor side from meter of MCB to motor i) Size 2.50 mm2 ii) Make iii) Type Armoured Power Cable iv) Capacity v) core-3 (B) Supply Side (From meter of HPSEB to Bus Bar & Switch) i) Size 2.50 mm2 ii) Make iii)Type - Armounred power cable iv) Capacity v) Core 3

Providing and fixing double loop earthing with GI plate of 600x600x6.30mm thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer - in - Charge.. i) Copper flat GI 8 SWG upto 15 HP

Centrifugal Pumping Machinery alongwith allied accessories for Badehra (R/main-1st) Providing horizontal spindle, horizontal / radial split casing /end suction ( back pull out arrange-ment) Single /double /multi stage of Kirloskar / KSB Crupton KSB/Calama/BS/ Groundfos/ Hindustan/ Lubbi make as per BIS IS 1520-1980 with upto date ammendments read with IS: 9137-1978 or latest edition suitable for lifting water for under mentioned characteristic with Bronze impellers / priming funnels, casing ring and shaft sleeves of Bronze shaft of stainless steel with cast iron casing, coupled directly through a flexible coupling on a common cast iron / cast steel base plate (base plate to be framed from the manufacturers of the pumping unit only) to slipring / Squirrel cage screen protected drip proof induction motor / motors of standard make such as Crompton / NGEF / GEC / Seimens /Jyoti/ Kirloskar BHEL / ABB suitable for operation on 415 (+/-15%) volts. 50 Cycles /Sec. 3 phase AC electric supply of 2900 RPM.The power of electric motor/ motors should be at least +10% in excess of the maximum power required by the pump / pumps in the Operation range of (+10%) and (-15%) of the duty point head. The motor / motors as per IS 325 IS -1978 with upto date amendments read with IS 900 -1972. It should include cost of Bearing. Nuts, Bolts and painting etc. and should meet the following requirements.

Discharge =( Q) 3.93 LPS

Total Head =( H) 39.30 Mts.

a)LWL In clear water Tank = 333.00 mtr

b) R.L. of shaft = 333.45 Mtrs.

c) R.L. of discharge Point. =362.00 mtrs.

d) Suction lift. +tive mtrs.

e)Discharge Head = 0.0 mtrs.

f) Static Head = 28.55 mtrs.

Rising main.

Length = 400.00 mtrs.

Diameter = 80mm. dia

Class GMS Tube (MG)

Pumping hours. 16.00 hours.

Altitude of installations above M.S.L 337 mtrs.

Characteristic of Water

a)Temperature _____20___Deg.Col.

b)Turbidity ________ JTU

c) Alloanity _________ mg/1 ca Co3

d)Size of solids __________ mm

e) Others.

(a) Pumps: Specifications:

i)Make

ii)Model.

iii)No.of stages:-

iv)Manufacturers

certificate to be attached.

Performance

i)Discharge:-

ii)Total Head:-

iii)B.H.P.

iv)Efficiency:

vi)Performance Curve to be attached.

b)Motors: Specifications.

i)Make

ii)Model

iii)Rating

iv)Speed.

v)Insulation.

(C) Coupling:

(d) Base Plate.

Providing ICTP Main Switch with HRC fuses of L&T/ Havells make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments. ICTP Switch: i) Make : ii) Type : iii) Capacity : 32 Amp.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. . Panel /Switch Board. i) Drawing.ii) layout Plan.

MCB of L&T/ Havells make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. MCB 1) Make. ii) Type iii) Range. 32 Amp. iv) Capacity

ii) ELCB of recommended make L&T / Havells as per IS ; 2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELCB 1) Make. ii) Type iii) Range. 63 Amp. iv) Capacity.

iii) The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage,reverse phasing,overloading and phase voltage difference as per IS; 3842 ( Latest Edition ) Volatage Monitor Relay i) Make ii ) Type iii) Range 0-500

Power factor meter of standard make as per relevent IS code with upto date ammendments. Power factor meter i) Make ii ) Type iii) Range 0-500

Frequency meter of standard make as per relevent IS code with upto date ammendments. Frequency meter i) Make ii ) Type iii) Range 0-500

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments including. Bus Bar Chamber i) Type ii) Make iii) Rating

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments. 3 phase indicators

e) Capacitor of BHEL / GEC / L&T / Mecheil make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. Capacitor i) Type ii) Make iii) Range 2KVAR

Providing suitable Air break type star delta starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments. Starter i) Type ii) Make Single phase preventor i) Type ii) Make

Providing and fixing double flanged cast Iron Sluice valve as per BIS 1414/API 600 with upto date ammendmnent of Kirloskar / Leader/ Kartar/ LP brand make for the suction pipe of 80 mm dia Class ASA 600 for the suction line of pump . Sluice Valve i)Make ii) Class ASA 600 iii)Test working head. iv) Material: Cast Steel

Providing and fixing double flanged Cast Iron Sluice valve of Leader / Kirloskar/ Kartar/LP brand make of 80 mm dia for the delivery line of pump and capable of with standing normal Seat Pressure as per BIS 1414/API 600 with upto date ammendments. For delivery pipe of pump. 80mm Sluice Valve i)Make ii) Class ASA 600 iii)Test working head iv) Material:-Cast Steel

Providing and fixing double flanged swing type cast Iron Reflux valves of Leader/ Kirloskar/ Kartar/LP brand make of 80 mm dia Class ASA 600 for delivery line of pump and capable of with standing the normal seat pressure and as per IS: 1868/API 6D with upto date ammendments. 80 mm dia Reflux Valve i)Make ii) Class ASA 600 iii)Test working head. iv) Material:-Cast Steel

Providing and fixing double flanged swing type cast Iron Reflux valves of Leader / Kirloskar/ Kartar/ LP brand make of 80 mm dia Class ASA 600 having by pass arrangement for the Rising main of the Pump and capable of with standing the normal seat pressure and as per IS: 1868/API 6D with upto date ammendments.Reflux Valve i)Make ii) Class ASA 600 iii)Test working head. iv) Material:-Cast Steel

Providing and fixing 25 mm dia steel circular dial pressure gauge of Precision / Fiebig make complete with all accessories such as stop cock,Copper tubing etc.as per IS: 3624-1987 with upto date ammendments. Pressure Gauge i) Make ii Range

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and Fixing double flanged GMS piping work ( Layout to be approved by Engineer-in-Charge). for suction and delivery pipes suitable to pumps offered and common header as per the rising main respectively complete with all specials such as bends,Tees, Reducers / Inceasers with companion flanges matching with the relevant specifications of the accessories as indicated in the Drawing including rubber / asbestos gasket of 3 mm thickness as per IS : 2712-1972 and required number of Nuts and Bolts as per 1364-1983.-the pipes shall be as per relevent IS code and to withstand 1.50 times total head stipulated under item No.30.The size of various components to be as under:-

i) Suction Pipe 65 mm dia.

ii) Delivery Pipe 80 mm dia.

iii) Common Header 80 mm dia. and will extend upto 5 metres from the outer wall of the pump house in the direction of Rising main of 80 mm dia to be joined.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor. Armoured Power Cable A) Motor side from meter of MCB to motor i) Size 2.50 mm2 ii) Make iii) Type Armoured Power Cable iv) Capacity v) core-3 (B) Supply Side (From meter of HPSEB to Bus Bar & Switch) i) Size 2.50 mm2 ii) Make iii)Type - Armounred power cable iv) Capacity v) Core 3

Providing and fixing double loop earthing with GI plate of 600x600x6.30mm thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer - in - Charge.. i) Copper flat GI 8 SWG upto 15 HP

Centrifugal Pumping Machinery alongwith allied accessories for Badehra (R/main-2nd) Providing horizontal spindle, horizontal / radial split casing /end suction ( back pull out arrangement ) Single /double /multi stage of Kirloskar / KSB/ Hindustan/ lubbi/ Groundfos Crupton KSB/Calama/BS/ make as per BIS IS 1520-1980 with upto date ammendments read with IS: 9137-1978 or latest edition suitable for lifting water for under mentioned characteristic with Bronze impellers / priming funnels, casing ring and shaft sleeves of Bronze shaft of stainless steel with cast iron casing, coupled directly through a flexible coupling on a common cast iron / cast steel base plate (base plate to be framed from the manufacturers of the pumping unit only) to slipring / Squirrel cage screen protected drip proof induction motor / motors of standard make such as Crompton / NGEF / GEC / Seimens /Jyoti/ Kirloskar BHEL / ABB suitable for operation on 415 (+/-15%) volts. 50 Cycles /Sec. 3 phase AC electric supply of 2900 RPM.The power of electric motor/ motors should be at least +10% in excess of the maximum power required by the pump / pumps in the Operation range of (+10%) and (-15%) of the duty point head. The motor / motors as per IS 325 IS -1978 with upto date amendments read with IS 900 -1972. It should include cost of Bearing. Nuts, Bolts and painting etc. and should meet the following requirements.

Discharge =( Q)6.53 LPS

Total Head =( H) 108.19 Mts.

a)LWL In clear water Tank = 333.00 mtr

b) R.L. of shaft = 333.45 Mtrs.

c) R.L. of discharge Point. =403.00 mtrs.

d) Suction lift. +tive mtrs.

e)Discharge Head = 0.0 mtrs.

f) Static Head = 70.00 mtrs.

Rising main.

Length = 2350.00 mtrs.

Diameter = 100mm. dia

Class GMS Tube (MG)

Pumping hours. 16.00 hours.

Altitude of installations above M.S.L 333 mtrs.

Characteristic of Water

a)Temperature _____20___Deg.Col.

b)Turbidity ________ JTU

c) Alloanity _________ mg/1 ca Co3

d)Size of solids __________ mm

e) Others.

(a) Pumps: Specifications:

i)Make

ii)Model.

iii)No.of stages:-

iv)Manufacturers

certificate to be attached.

Performance

i)Discharge:-

ii)Total Head:-

iii)B.H.P.

iv)Efficiency:

vi)Performance Curve to be attached.

b)Motors: Specifications.

i)Make

ii)Model

iii)Rating

iv)Speed.

v)Insulation.

(C) Coupling:

(d) Base Plate.

Providing ICTP Main Switch with HRC fuses of L&T/ Havells make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments. ICTP Switch: i) Make : ii) Type : iii) Capacity : 63 Amp.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. . Panel /Switch Board. i) Drawing.ii) layout Plan.

MCB of L&T/ Havells make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. MCB 1) Make. ii) Type iii) Range. iv) Capacity 63 Amp.

ii) ELCB of recommended make L&T / Havells as per IS ; 2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELCB 1) Make. ii) Type iii) Range. iv) Capacity. 63 Amp.

iii) The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage,reverse phasing,overloading and phase voltage difference as per IS; 3842 ( Latest Edition ) Volatage Monitor Relay i) Make ii ) Type iii) Range 0-500

Power factor meter of standard make as per relevent IS code with upto date ammendments. Power factor meter i) Make ii ) Type iii) Range 0-500

Frequency meter of standard make as per relevent IS code with upto date ammendments. Frequency meter i) Make ii ) Type iii) Range 0-500

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments including. Bus Bar Chamber i) Type ii) Make iii) Rating

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments. 3 phase indicators

e) Capacitor of BHEL / GEC / L&T / make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. Capacitor i) Type ii) Make iii) Range 4KVAR

Providing suitable Air break type star delta starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments. Starter i) Type ii) Make Single phase preventor i) Type ii) Make

Providing and fixing double flanged cast steel Sluice valve as per BIS 1414/API 600 with upto date ammendmnent of Kirloskar / Leader/ Kartar/ LP brand make for the suction pipe of 100 mm dia Class ASA 300 for the suction line of pump . Sluice Valve i)Make ii) Class ASA 150 iii)Test working head. iv) Material: Cast Steel

Providing and fixing double flanged Cast steel Sluice valve of Leader / Kirloskar/ Kartar/LP brand make of 80 mm dia for the delivery line of pump and capable of with standing normal Seat Pressure as per BIS 1414/API 600 with upto date ammendments. For delivery pipe of pump. 80 mm Sluice Valve i)Make ii) Class ASA 600 iii)Test working head iv) Material:-Cast Steel

Providing and fixing double flanged swing type cast steel Reflux valves of Leader/ Kirloskar/ Kartar/LP brand make of 100 mm dia Class ASA 150 for delivery line of pump and capable of with standing the normal seat pressure and as per IS: 1868/API 6D with upto date ammendments. 100 mm dia Reflux Valve i)Make ii) Class ASA 300 iii)Test working head. iv) Material:-Cast Steel

Providing and fixing double flanged swing type cast steel Reflux valves of Leader / Kirloskar/ Kartar/ LP brand make of 100 mm dia Class ASA 150 having by pass arrangement for the Rising main of the Pump and capable of with standing the normal seat pressure and as per IS: 1868/API 6D with upto date ammendments.Reflux Valve i)Make ii) Class ASA 150 iii)Test working head. iv) Material:-Cast Steel

Providing & fixing pressure gauge of Prega / Precision / Fiebig make complete with all accessories such as stop cock, copper tubing as per IS ; 3624-1987 with upto date amendements Pressure Gauge i) Make

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and Fixing double flanged GMS piping work ( Layout to be approved by Engineer-in-Charge). for suction and delivery pipes suitable to pumps offered and common header as per the rising main respectively complete with all specials such as bends,Tees, Reducers / Inceasers with companion flanges matching with the relevant specifications of the accessories as indicated in the Drawing including rubber / asbestos gasket of 3 mm thickness as per IS : 2712-1972 and required number of Nuts and Bolts as per 1364-1983.-the pipes shall be as per relevent IS code and to withstand 1.50 times total head stipulated under item No.30.The size of various components to be as under:-

i) Suction Pipe 80 mm dia.

ii) Delivery Pipe 100 mm dia.

iii) Common Header 100 mm dia. and will extend upto 5 metres from the outer wall of the pump house in the direction of Rising main of 100 mm dia to be joined.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor. Armoured Power Cable A) Supply side from meter of HPSEB to Bus Bar and Switch i) Size 4mm2 ii) Make iii) Type iv) Capacity v) core B) Motor side (i) Size: 2.5mm2 ii) Make: iii) Type:

Providing and fixing double loop earthing with Copper plate of 600x600x6.3mm thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt,25x5mm strip as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer - in - Charge.. i) GI wire 8 SWG

Centrifugal Pumping Machinery alongwith allied accessories for Panjawar (R/main-1st) Providing horizontal spindle, horizontal / radial split casing /end suction ( back pull out arrange-ment) Single /double /multi stage of Kirloskar / KSB Crupton KSB/Calama/BS/ Groundfos/ Hindustan/ Lubbi make as per BIS IS 1520-1980 with upto date ammendments read with IS: 9137-1978 or latest edition suitable for lifting water for under mentioned characteristic with Bronze impellers / priming funnels, casing ring and shaft sleeves of Bronze shaft of stainless steel with cast iron casing, coupled directly through a flexible coupling on a common cast iron / cast steel base plate (base plate to be framed from the manufacturers of the pumping unit only) to slipring / Squirrel cage screen protected drip proof induction motor / motors of standard make such as Crompton / NGEF / GEC / Seimens /Jyoti/ Kirloskar BHEL / ABB suitable for operation on 415 (+/-15%) volts. 50 Cycles /Sec. 3 phase AC electric supply of 2900 RPM.The power of electric motor/ motors should be at least +10% in excess of the maximum power required by the pump / pumps in the Operation range of (+10%) and (-15%) of the duty point head. The motor / motors as per IS 325 IS -1978 with upto date amendments read with IS 900 -1972. It should include cost of Bearing. Nuts, Bolts and painting etc. and should meet the following requirements.

Discharge =( Q)3.85LPS

Total Head =( H) 52.81 Mts.

a)LWL In clear water Tank = 375.05 mtr

b) R.L. of shaft = 375.50 Mtrs.

c) R.L. of discharge Point. =409.00 mtrs.

d) Suction lift. +tive mtrs.

e)Discharge Head = 0.0 mtrs.

f) Static Head = 33.50 mtrs.

Rising main.

Length = 950.00 mtrs.

Diameter = 80mm. dia

Class GMS Tube (MG)

Pumping hours. 16.00 hours.

Altitude of installations above M.S.L 376 mtrs.

Characteristic of Water

a)Temperature ___20_____Deg.Col.

b)Turbidity ________ JTU

c) Alloanity _________ mg/1 ca Co3

d)Size of solids __________ mm

e) Others.

(a) Pumps: Specifications:

i)Make

ii)Model.

iii)No.of stages:-

iv)Manufacturers

certificate to be attached.

Performance

i)Discharge:-

ii)Total Head:-

iii)B.H.P.

iv)Efficiency:

vi)Performance Curve to be attached.

b)Motors: Specifications.

i)Make

ii)Model

iii)Rating

iv)Speed.

v)Insulation.

(C) Coupling:

(d) Base Plate.

Providing ICTP Main Switch with HRC fuses of L&T/ Havells make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments. ICTP Switch: i) Make : ii) Type : iii) Capacity : 32 Amp.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. . Panel /Switch Board. i) Drawing.ii) layout Plan.

MCB of L&T/ Havells make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. MCB 1) Make. ii) Type iii) Range. iv) Capacity 32 Amp.

ii) ELCB of recommended make L&T / Havells as per IS ; 2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELCB 1) Make. ii) Type iii) Range. iv) Capacity. 63 Amp.

iii) The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage,reverse phasing,overloading and phase voltage difference as per IS; 3842 ( Latest Edition ) Volatage Monitor Relay i) Make ii ) Type iii) Range 0-500

Power factor meter of standard make as per relevent IS code with upto date ammendments. Power factor meter i) Make ii ) Type iii) Range 0-500

Frequency meter of standard make as per relevent IS code with upto date ammendments. Frequency meter i) Make ii ) Type iii) Range 0-500

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments including. Bus Bar Chamber i) Type ii) Make iii) Rating

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments. 3 phase indicators

e) Capacitor of BHEL / GEC / L&T / Mecheil make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. Capacitor i) Type ii) Make iii) Range 2KVAR

Providing suitable starter direct online of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments. Starter i) Type ii) Make Single phase preventor i) Type ii) Make

Providing and fixing double flanged cast steel Sluice valve as per BIS 1414/API 600 with upto date ammendmnent of Kirloskar / Leader/ Kartar/ LP brand make for the suction pipe of 80 mm dia Class ASA 150 for the suction line of pump . Sluice Valve i)Make ii) Class ASA 150 iii)Test working head. iv) Material: Cast Steel

Providing and fixing double flanged Cast steel Sluice valve of Leader / Kirloskar/ Kartar/LP brand make of 80 mm dia for the delivery line of pump and capable of with standing normal Seat Pressure as per BIS 1414/API 600 with upto date ammendments. For delivery pipe of pump. 80 mm Sluice Valve i)Make ii) Class ASA 150 iii)Test working head. iv) Material:-Cast Steel

Providing and fixing double flanged swing type cast steel Reflux valves of Leader/ Kirloskar/ Kartar/LP brand make of 80 mm dia Class ASA 150 for delivery line of pump and capable of with standing the normal seat pressure and as per IS: 1868/API 6D with upto date ammendments. 50 mm dia Reflux Valve i)Make ii) Class ASA 150 iii)Test working head. iv) Material:-Cast Steel

Providing and fixing double flanged swing type cast steel Reflux valves of Leader / Kirloskar/ Kartar/ LP brand make of 80 mm dia Class ASA 150 having by pass arrangement for the Rising main of the Pump and capable of with standing the normal seat pressure and as per IS: 1868/API 6D with upto date ammendments.Reflux Valve i)Make ii) Class ASA 150 iii)Test working head. iv) Material:-Cast Steel

Providing and fixing 25 mm dia steel circular dial pressure gauge of Precision / Fiebig make complete with all accessories such as stop cock,Copper tubing etc.as per IS: 3624-1987 with upto date ammendments. Pressure Gauge i) Make ii Range

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and Fixing double flanged GMS piping work ( Layout to be approved by Engineer-in-Charge). for suction and delivery pipes suitable to pumps offered and common header as per the rising main respectively complete with all specials such as bends,Tees, Reducers / Inceasers with companion flanges matching with the relevant specifications of the accessories as indicated in the Drawing including rubber / asbestos gasket of 3 mm thickness as per IS : 2712-1972 and required number of Nuts and Bolts as per 1364-1983.-the pipes shall be as per relevent IS code and to withstand 1.50 times total head stipulated under item No.30.The size of various components to be as under:-

i) Suction Pipe 65 mm dia.

ii) Delivery Pipe 80 mm dia.

iii) Common Header 80 mm dia. and will extend upto 5 metres from the outer wall of the pump house in the direction of Rising main of 80 mm dia to be joined.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor. Armoured Power Cable A) Supply side from meter of HPSEB to Bus Bar and Switch i) Size 2.5mm2 ii) Make iii) Type iv) Capacity v) core B) Motor side (i) Size: 2.5mm2 ii) Make: iii) Type:

Providing and fixing double loop earthing with GI plate of 600x600x6.30mm thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer - in - Charge.. i) Copper flat GI 8 SWG upto 15 HP

Centrifugal Pumping Machinery alongwith allied accessories for Panjawar (R/main-2nd) Providing horizontal spindle, horizontal / radial split casing /end suction ( back pull out arrangement ) Single /double /multi stage of Kirloskar / KSB/ Hindustan/ lubbi/ Groundfos Crupton KSB/Calama/BS/ make as per BIS IS 1520-1980 with upto date ammendments read with IS: 9137-1978 or latest edition suitable for lifting water for under mentioned characteristic with Bronze impellers / priming funnels, casing ring and shaft sleeves of Bronze shaft of stainless steel with cast iron casing, coupled directly through a flexible coupling on a common cast iron / cast steel base plate (base plate to be framed from the manufacturers of the pumping unit only) to slipring / Squirrel cage screen protected drip proof induction motor / motors of standard make such as Crompton / NGEF / GEC / Seimens /Jyoti/ Kirloskar BHEL / ABB suitable for operation on 415 (+/-15%) volts. 50 Cycles /Sec. 3 phase AC electric supply of 2900 RPM.The power of electric motor/ motors should be at least +10% in excess of the maximum power required by the pump / pumps in the Operation range of (+10%) and (-15%) of the duty point head. The motor / motors as per IS 325 IS -1978 with upto date amendments read with IS 900 -1972. It should include cost of Bearing. Nuts, Bolts and painting etc. and should meet the following requirements.

Discharge =( Q) 7.45 LPS

Total Head =( H) 122.96 Mts.

a)LWL in clear water Tank = 375.05 mtr

b) R.L. of shaft = 375.50 Mtrs.

c) R.L. of discharge Point. =433.10 mtrs.

d) Suction lift. +tive mtrs.

e)Discharge Head = 0.0 mtrs.

f) Static Head = 57.00 mtrs.

Rising main.

Length = 3250.00 mtrs.

Diameter = 1000mm. dia

Class GMS Tube (MG)

Pumping hours. 16.00 hours.

Altitude of installations above M.S.L 376 mtrs.

Characteristic of Water

a)Temperature ___20_____Deg.Col.

b)Turbidity ________ JTU

c) Alloanity _________ mg/1 ca Co3

d)Size of solids __________ mm

e) Others.

(a) Pumps: Specifications:

i)Make

ii)Model.

iii)No.of stages:-

iv)Manufacturers

certificate to be attached.

Performance

i)Discharge:-

ii)Total Head:-

iii)B.H.P.

iv)Efficiency:

vi)Performance Curve to be attached.

b)Motors: Specifications.

i)Make

ii)Model

iii)Rating

iv)Speed.

v)Insulation.

(C) Coupling:

(d) Base Plate.

Providing ICTP Main Switch with HRC fuses of L&T/ Havells make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments. ICTP Switch: i) Make : ii) Type : iii) Capacity : 63 Amp.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. . Panel /Switch Board. i) Drawing.ii) layout Plan.

MCB of L&T/ Havells make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. MCB 1) Make. ii) Type iii) Range. iv) Capacity 63 Amp.

ii) ELCB of recommended make L&T / Havells as per IS ; 2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELCB 1) Make. ii) Type iii) Range. iv) Capacity. 63 Amp.

iii) The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage,reverse phasing,overloading and phase voltage difference as per IS; 3842 ( Latest Edition ) Volatage Monitor Relay i) Make ii ) Type iii) Range 0-500

Power factor meter of standard make as per relevent IS code with upto date ammendments. Power factor meter i) Make ii ) Type iii) Range 0-500

Frequency meter of standard make as per relevent IS code with upto date ammendments. Frequency meter i) Make ii ) Type iii) Range 0-500

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments including. Bus Bar Chamber i) Type ii) Make iii) Rating

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments. 3 phase indicators

e) Capacitor of BHEL / GEC / L&T / Mecheil make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. Capacitor i) Type ii) Make iii) Range 5KVAR

Providing suitable oil immersed star delta starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments. Starter i) Type ii) Make Single phase preventor i) Type ii) Make

Providing and fixing double flanged cast steel Sluice valve as per BIS 1414/API 600 with upto date ammendmnent of Kirloskar / Leader/ Kartar/ LP brand make for the suction pipe of 100 mm dia Class ASA 300 for the suction line of pump . Sluice Valve i)Make ii) Class ASA 300 iii)Test working head. iv) Material: Cast Steel

Providing and fixing double flanged Cast steel Sluice valve of Leader / Kirloskar/ Kartar/LP brand make of 100 mm dia for the delivery line of pump and capable of with standing normal Seat Pressure as per BIS 1414/API 600 with upto date ammendments. For delivery pipe of pump. 100 mm Sluice Valve i)Make ii) Class ASA 300 iii)Test working head. iv) Material:-Cast Steel

Providing and fixing double flanged swing type cast steel Reflux valves of Leader/ Kirloskar/ Kartar/LP brand make of 100 mm dia Class ASA 300 for delivery line of pump and capable of with standing the normal seat pressure and as per IS: 1868/API 6D with upto date ammendments. 100 mm dia Reflux Valve i)Make ii) Class ASA 300 iii)Test working head. iv) Material:-Cast Steel

Providing and fixing double flanged swing type cast steel Reflux valves of Leader / Kirloskar/ Kartar/ LP brand make of 100 mm dia Class ASA 300 having by pass arrangement for the Rising main of the Pump and capable of with standing the normal seat pressure and as per IS: 1868/API 6D with upto date ammendments.Reflux Valve i)Make ii) Class ASA 300 iii)Test working head. iv) Material:-Cast Steel

Providing & fixing pressure gauge of Prega / Precision / Fiebig make complete with all accessories such as stop cock, copper tubing as per IS ; 3624-1987 with upto date amendements Pressure Gauge i) Make

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and Fixing double flanged GMS piping work ( Layout to be approved by Engineer-in-Charge). for suction and delivery pipes suitable to pumps offered and common header as per the rising main respectively complete with all specials such as bends,Tees, Reducers / Inceasers with companion flanges matching with the relevant specifications of the accessories as indicated in the Drawing including rubber / asbestos gasket of 3 mm thickness as per IS : 2712-1972 and required number of Nuts and Bolts as per 1364-1983.-the pipes shall be as per relevent IS code and to withstand 1.50 times total head stipulated under item No.30.The size of various components to be as under:-

i) Suction Pipe 80 mm dia.

ii) Delivery Pipe 100 mm dia.

iii) Common Header 100 mm dia. and will extend upto 5 metres from the outer wall of the pump house in the direction of Rising main of 100 mm dia to be joined.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor. Armoured Power Cable A) Supply side from meter of HPSEB to Bus Bar and Switch i) Size 6mm2 ii) Make iii) Type iv) Capacity v) core B) Motor side (i) Size: 4mm2 ii) Make: iii) Type:

Providing and fixing double loop earthing with Copper plate of 600x600x6.3mm thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt,25x5mm strip as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer - in - Charge.. i) GI wire 4 SWG

Schedele B3- Civil Work (Pump house & boundary wall)

Excavation in foundation trenches etc. in earth work lift up to 1.5 mtrs. Stacking the excavated soil not more than 3 metres away from the edge of excavation and then returning the stacked soil in 15 cm layers when required in to plinth and sides of foundations, consolidating each deposited layer by ramming , watering and then disposing of all surplus excavated earth as directed with in a lead of 20 metres in pick jumper work.

Providing and laying cement concrete 1:6:12 ( 1 cement : 6 sand : 12 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth.

Ist class brick work using common burnt clay building bricks in foundation and plinth in cement mortor 1:6 ( 1 cement: 6 sand ) comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Boulder filling under floor dry hand packed tightly comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring shuttering ,strutting and propping etc.with wooden battens and ballies,height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for in situ reinforced concrete and plain concrete work in comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge. :-

Foundation footing bases of columns etc and mass concrete.

Columns, pillars, post and struts.

i) Square, rectangular or polygonal in plan.

ii) Circular in plan.

Beams,cantilivers,girders and lintels sides and soffits of beams,beam haunchings, cantilivers , girders, bressumers and lintels not exceeding 1 metre in depth.

EDGES OF SLABS AND BREAKS IN FLOORS & WALLS (UNDER 20 CMT. WIDE)

Providing and laying cement concrete 1:2:4 ( 1cement:2 sand: 4graded stone aggregate 20 mm nominal size )and curing complete excluding the cost of form work and reinforcement in:-

Foundation footings bases of columns and the like and mass concrete.

Colunms pillars posts and struts upto floor two level.

i) Square or rectangalar in Plan.

ii) Circular in plan.

Suspended floors, roofs,landings and shelves and their supports, balconies, beams, girders, bressumers and cantilivers up to floor two level.

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete up to floor two levelcomlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Ist class brick work using common burnt clay building bricks in superstructure in cement mortor 1:6 (1 cement :6 sand) comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Providing and fixing pressed steel doors frames manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges, jump lock jamb, beed and if required angle threshold of mild steel angle of section 50X25 mm or base ties of 1.25 mm pressed mild steel welded or regidly fixed together by mechanical means, adjustable lugs with split and tails to each jamb including steel but things 2.5 mm thick with gaurds, lock strike plate and shock as specified and applying a coat of approved steel primer after pretreatment of the surfacecomlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Providing and fixing panneled glazed or panelled and glazed shutters for doors, windows and clerestory windows,including black enamelled iron butt hinges with necessary screws. 45 mm thick.2nd class deodar wood comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Providing & fixing M.S. grills of required pattern in wooden frame of window etc.with M.S. flats, square or round barswith round headedbolts and nuts by screws plain grills comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Cement concrete flooring 1:2:4 (1 cement : 2 sand :4 graded stone aggregate 20 mm nominal size) laid in one layer finished with a floating of neat cement comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.40 mm thick

6mm cement plaster to ceiling in CM 1:3 ( 1Cement :3 Sand) comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

15 mm cement plaster in single coat on rough side of brick/concrete stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 (1 cement:6 sand)comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Pointing on brick work with cement mortor 1:3 ( 1 cement: : 3 sand ) comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.Raised and cut

White washing with lime on undecorated wall surfaces two coats to give an even shade including thoroughly brooming the surface to remove all dirt , dust and other foreign matters comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Distempering with dry distemper of approved brand and manufacture (two coats) and of required shade on undecorated wall surfaces to give an even shade sand papered smooth comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Applying priming coat on new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,greese,dirt and other foreign matters,sand papering and knotting.Ready mixed paint brushing wood primer pink comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Painting two coats (excluding priming coat) on new wood and wood based surfaces,with enamel paint to give an even shade including cleaningthe surface of dirt ,dust and other foreign matters sand papering and stopping with enamel paint other than white comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Providing and fixing sliding door bolts anodized transparent or dyed to required shade and colour with screws etc. complete in all respect

Providing and fixing tower bolts barrel type anodized transport or dyed to required shade and colour with screws com lete in all respect.

Providing and fixing aluminium handle anodized transparent or dyed to required shade and colour with screws etc. complete in all respect

Providing and fixing MS Hooks and eyes 250 mm to required shade and colour with screws etc. complete in all respect

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1cement:3sand:6 graded stone aggregate 20 mm nominal size comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Proving under layer for plinth protection of 75 mm thick (unconsolidated) bed dry brick / stone Aggregate 40 mm nominal size will rammed with rammed and consolidated and grouted with fine sand including preparation of ground.

White glazed tiles 6 mm thick in flooring cement mortar 1:3 (1cement : 3 sand) finished with flush pointing in white cement comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

White glazed tiles 6 mm thick in flooring cement mortar 1:3 (1cement : 3 sand) finished with flush pointing in white cement comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

1st. Class Half brick work using common burnt clay building bricks in super structure above 1st. floor level in cement mortar 1 : 4 ( 1 cement :4 sand) of complete in all lead and lifts as per the direction of the Engineer-in-Charge.

Steel work welded in built up sections,trusses and framed work including cutting hoisting fixing in position and applying a priming coat of red lead paint comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.In trusses and trussed purlings in buildings.

Providing & fixing 0.60 mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 micron over 5 micron primer coating to back coat of polyster of 5 micron over 5 micron primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm diameter s with prepainted limpet rubber washers complete with all accessories as required comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge. 0.60 mm thick sheet.

Providing ridges or hips 60cm over all in plinth with galvanised iron G.I. sheet fixed J or L hooks bolts and nuts 8mm dia G.I limpet and bitumen washers complete.i) 0.63 mm thick sheet.

Providing valley 90cm over all in plain G.I. sheets fixed with galvanised iron J or L hooks bolts and nuts 8mm dia G.I. limpet and bitumen washers comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Providing of Manually operated gantry to hoisting Chain pulley with other hoisting mechanism capacity of 6 MT comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

Excavation in earth work and filling in 15 cm. layers in foundation & plinths including ramming, watering and consolidating complete in all respect including carriage of materials within all leads and lifts and as per the direction of the Engineer-in-Charge.

Finishing wall with water proofing cement paint of approved brand & manufacturer & of required shade on undecorated wall surfaces ( Two coats) to give an even shade after throughly brushing the surfaces to remove all dirt, dust and remain of loose powdered material. in all leads and lifts and as per the dirction of the Engineer- in - charge.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint to give an even shade including cleaning the surface of dirt ,dust and other foreign matter with enamel with enamel paint other than white complete in all respect as per the direction of the Engineer-in-Charge.

Provision for Solar teck stand dusk to dawn automatic operation with 74 Watt panel, 74 Ah tubular battery with 1x11 watt CFL with two days autonomy with 5 mtrs pole.

C/O OHSR, Collection and under ground reserviors (MBR/SR)

Excavation in foundations,trenches etc., in earth work, lift upto 1.50 mts. Stacking the excavated soil not more than 3 mts. Clear from the edge of the excavation & then returning the stacked soil in 15 cms. Layers,when required into plinths sides of foundation etc.,consolidating each deposited layers by ramming & watering & then disposing of all surplus excavated earth as dierected within all leads & lifts as per entire satisfaction of Engineer in charge.

Providing & laying cement concrete M-10 mix concrete using graded stone aggregate 40 mm nominal size, excluding the cost of centring & shuttering in Foundation & plinth.

Providing & laying cement concrete M- 30 mix concrete using not leaner than 1:1.5:3 aggregate 20 mm nominal size) & curing complete excluding the cost of form work & reinforcement for reinforced concrete work in :-

Foundation,footing.bases of columns & the like & the mass concrete.

(ii) Wall (any thickness but not less than 0.10 mts.Thickness)attached pillasters,buttresses plinth,& string courses etc.from top of found.level upto floor two level

(i) floor four level to floor five level

Column,pillars,posts & struts upto floor two level

(ii) floor two level to floor three level

(iii) floor three level to floor four level

(iv) floor four level to floor five level

Lintels,beams girders bressumers & cantilevers upto floor two level

(ii) floor two level to floor three level

(iii) floor three level to floor four level

Arches upto floor two level:

(ii) floor two level to floor three level

(iii) floor three level to floor four level

Suspended floors,roofs,landings.etc. upto floor two level

(i) floor two level to floor three level

(ii) floor three level to floor four level

Prov.form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm,so as to give a fair finish i/c centring shuttering,strutting & propping etc. with wooden battens & ballies,ht. of propping & centring below supporting floor to ceiling not exceeding 4.00 mts. & removal of the same for in situ-reinforced concrete & plain concrete work :-

(i) Foundation,footing,bases of columns etc.and mass concrete.

(ii) Flat surface such as soffits of suspended floors,roofs,landing and the like

(iii) Vertical surfaces such as walls (any thickness) partitions and the like i/c attached pillasres buttresses, plinth & string courses and the like.

(a) Upto 4.00 mtrs.

For Vertical surfaces of tank

(iv) Columns,pillars.posts & struts.

(b) Beyond 4.00 mtrs.

(v) Beams, cantilever, girders & lintels.

Sides & soffits of beams,beam haunchings, catilevers, bressumers & lintels not exceeding 1.00 mtr.depth in all ht.from floor.

Providing form work of ordinary timber plankings, so as to give a rough finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4.00 mtrs.height.

Beyond 4.00 mtr.height.

Providing Tor steel reinforcement for RCC work including bending,binding & placing in position complete upto floor two level in all respect.

Providing in RCC work smooth finishing of the exposed surface with cement mortor 1:3 (1cement :3 Sand) complete in all respect within all leads & lifts.

Finishing wall with water proofing cement paint of approved brand & maunfacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after throughly brushing the surface to remove all dirt & remains of loose powedered material etc.

Providing & fixing 500 mm dia.SFRC man hole cover with frame and the weight of frame & cover should not be less than 100 kg complete in all respect within all leads & lifts.

Providing and fixing of GMS Pipes conforming to relevants BIS codes of below mentioned diameters fully jointed with MS Flanges of Table - 5 as per IS :6392 - 1971 excluding the cost of excavation in trenches complete in all respect within all leads & lifts.

100 mm Inlet pipe, Outlet pipe, Over flow pipe & Scour pipe

Steel work welded in built up sections,trusses & framed work i/c cutting, hoisting,fixing in position & applying a priming coat of red paint.In grating,framed guard bars,ladders,railing,brackets & similar works.

Providing and fixing of GMS Pipes conforming to IS 1239 - 1979 (Part-1) screwed & socketed joints (Light grade) excluding the cost of excavation in trenches 50 mm

Providing & fixing CI sluice valve (with hand wheel) Leader/ Kirloskar/ Kartar make as per IS:780 - 1984 Class-I upto 300 mm dia i/c brass spindle & as per 2906 - 1984 Class II for diameters more than 300 mm complete with bolts,nuts,rubber insertion etc,(The tail pieces if required shade etc.

100 mm Inlet pipe, Outlet pipe, Over flow & Scour pipe

Providing & fixing bends of required degrees made from parent tubes conforming to relevant codes fully flanged with MS Flange of Table - 5 conforming to IS: 6392 - 1971 complete in all respect within all leads & lifts.

100 mm Inlet pipe, Outlet pipe, Over flow & Scour pipe

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 Cement: 3 Sand: 6graded stone aggregate 20 mm nominal size) complete in all respect within all leads & lifts.

Providing under layers for plinth protection 75 mm thick (unconslidated) bed dry brick/stone aggregate 40 mm nominal size well rammed & grouted with fine sand i/c preparation of ground complete in all respect within all leads & lifts.

Constructing chamber for sluice valve, with CI surface box 100 mm top dia.,160 mm bottom dia.&180 mm deep (inside) with chained lid RCC top 1: 2: 4 mix (1 cement :2 Sand :4 graded stone aggregate 20 mm nominal size ) 100 mm thick foundation conc.1:5:10 mix (1cement : 5 sand : 10 graded stone aggregate 40 mm nominal size) & inside plastering with cement mortor 1:3 (1 Cement : 3 Sand ) finished with a floating coat of neat cment i/c curing complete. 600 x 600 x 750 mm inside size With 150mm thick walls of RCC 1:2:4 (1cement : 2 sand :4 graded stone aggregate 20 mm nominal size) complete with form work & reinforcement with 6 mm bars at not exceeding 150 mm centres both ways.

Providing and Fixing of below items required for OHSR complete.

MS Sheet Locking arrangement for Manhole

Lightening Conductor

Water measurement gauge

Vent Pipe including CI cowl complete

Flanged bell mouth alongwith puddle collars

Expansion joints

Provision of duck foot bends, Providing & fixing MS sheet locking arrangement for protecting the storage tanks

Schedule B5-Gravity mains and Distribution system:-

Excavation in foundation trenches ( for pipes and pits ) upto all depths in all classification of earth work such as pick work ,jumper work, saturated soil including bailing or pumping out water, blasting soft/hard rock or chieselling soft/ hard rock where blasting is prohibited, in all lifts including trimming and dressing of sides,levelling of beds to correct grade including,shoring,strutting,planking,timbering and dewatering wherever required,stacking the useable and unuseable material/soil separately and after laying, jointing and testing of pipes returning the useable soil in trenches in 15 cm (fiften centimeter ) layers including consolidating of such deposited layer by ramming and watering and then disposing of all surplus excavated soil /un-useable materials as directed within all leads and lifts including restoration of un-metalled surface to its original condition and including cost of diversion for traffic, night signals, fixing caution boards, crossing over trenches for access to houses, fencing etc. complete in all respect within all leads and lifts as per the directions of Engineer-in-Charge.

Providing, Laying, jointing and testing in trenches GMS pipes (light grade/Medium grade) confirming to ISI specification including commissioning and cost of all fittings in respect of following diameters in gravity mains/distribution system (earth work in trenches to be measured and paid for separately) including entire carriage of material comlete in all respect including all leads and lifts as per the direction of the Engineer-in-Charge.

25mm dia (L)

32 mm dia (L).

40 mm dia (L).

50 mm dia (L).

65 mm dia (L).

80 mm dia (L).

100 mm dia (L).

50 mm dia (M).

65 mm dia (M).

80 mm dia (M).

100 mm dia (M).

125 mm dia (M).

150 mm dia (M).

Providing and fixing C.I sluice valve ( with hand wheel ) as per IS 780 class upto 300 mm dia including brass spindle and as per IS- 2906 class II for diameter more than 300 mm complete with bolts,nuts,insertion etc.( The tail pieces if required shall be measured and paid for separately.) within all leads & lifts. Leader/ Kirloskar/ Kartar make

50 mm dia.

65 mm dia.

80 mm dia.

100 mm dia.

125 mm dia.

150 mm dia

Providing and fixing Cast iron single orifice kinetic air valve 25mm dia as per IS 14845 with bolts,nuts,insertion etc. Including tail pieces if required including entire carriage of material in all leads and lifts as per the direction of the Engineer- in-Charge.Leader/ Kirloskar/ Kartar make

Providing and fixing of copper alloy gate valves class-II for water works purpose as per 778-1984 (reaffirmed-2010) of the following diameters in distribution system including entire carriage of material in all leads and lifts as per the direction of the Engineer- in-Charge.Leader/ Kirloskar/ Kartar make

25mm dia.

32 mm dia

40mm dia

50mm dia

65 mm dia.

Dismentling of old GMS pipe in existing distribution system where changing is required of following diameters including staking of material at site in all leads & lift and as per the direction of Engineer-in-Charge.

15mm dia.(L)

20mm dia(L)

25mm dia (L)

32 mm dia (L).

40 mm dia (L).

50 mm dia (L).

65 mm dia (L).

80 mm dia(L)

Relaying of old serviceable GMS pipe of following diameters in all leads & lift and as per the direction of Engineer-in-Charge.

25mm dia (L)

32 mm dia (L).

40 mm dia (L).

50 mm dia (L).

65 mm dia (L).

80 mm dia(L)

Schedule A6 -Miscellaneous

Providing and Laying, jointing and testing in trenches GMS pipes (light grade) confirming to ISI specification including commissioning in respect of following diameters from service line upto individual house hold connection including earth work and entire carriage of material in all leads and lifts as per the direction of the Engineer- in-Charge.

15mm dia.

Providing fittings and accessories e.g. tee, union, nipple elbow, wheel valve, 1/4" ferrule, bib cock etc. required for house hold connection upto domestic storage tank. The 15 mm dia wheel valve shall confirm to BIS 778-1980 CL-1, all other G.I. fittings shall confirm to BIS specification

Providing and installation Computer Server for Management and Control and entire carriage of material in all leads and lifts as per the direction of the Engineer- in-Charge.

Providing and installation of flow measurement devices to be installed at discharge point of the tubewell, MBR and service storage tank with appropriate sensors along-with the provision with the required data transmission system to central station for analysis with appropriate power backup system and entire carriage of material in all leads and lifts as per the direction of the Engineer- in-Charge.

Supply, delivery, erection and commissioning of following capacity of micro-controller based water disinfection equipment using automatic gaseous chlorination process based on Oligodynamic technology i/c control panel, water chamber, electrode, interconnecting pipe line, field test kit, outer cabinet, voltage stabilizer, water flow meter, booster pump, booster bed pump, etc complete. 25000 LPH

SCHEDULE B7 OPERATION AND MAINTENANCE OF SCHEME FOR 5 YEARS

The Bidder shall carry out the operation and maintenance of the scheme right from source to tail ends of the scheme. The operation & maintenance shall be carried out as per the CPHEEO manual of water supply & treatment (Latest addition). All the structures & other components of the scheme should be kept neat and clean; he should report the any leakages, choking of lines and other damages of the scheme to the department immediately. He should maintain log books of running of pumping machinery and Register’s for conducting water samples and consumption of chemicals & flow meter readings etc. and submit the report to the department as per the direction of the Employer. For any breakdown of the scheme, he should repair/rectify the defects immediately and put the scheme functional immediately otherwise he shall be liable to penalise for Rs. 5000/- per day for delay in repair of the scheme. He should deploy sufficient skilled/un-skilled manpower on the scheme.Periodical white washing distempering & painting of all civil structures should be carried out. He is responsible to supply sufficient quantity and quality of water to the beneficiares.

Operation & maintenance for Ist year

Operation & maintenance for 2nd year

Operation & maintenance for 3rd year

Operation & maintenance for 4th year

Operation of maintenance for 5th year

M/s JAGDISH PRASAD AGARWAL

Unipro Techno Infrastructure Pvt Ltd

Lahoty Buildcon Limited