SPECIAL REPAIRS TO BLDG NO. P-103 (GTO OFFICE,24SSB) AT SCS AND OTHER REV MINOR WORKS UNDER GE (SOUTH) BANGALORE

Amount

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches n exc 1.5 m wide & n exc 1.5 m depth; for foundation, , laying of UG cables etc and getting out in soft/loose soil complete all as specified and directed.

M&L cement concrete 1:4:8 type D-2 (40 mm graded stone aggregate) as in foundations, filling & mass concrete complete all as specified and directed.

M & L reinforced cement concrete M-25 design mix (using 20 mm graded crushed stone aggregate) as in foundation, incl rafts, footings, foundation beams, plinth beams, bases for columns etc, basement slabs under reamed piles and mass concrete complete all as specified and directed.

M & L reinforced cement concrete M-25 design mix (using 20 mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M & L reinforced cement concrete M-25 design mix (using 20 mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

M & L reinforced cement concrete M-25 design mix (using 20 mm graded crushed stone aggregate) as in chajjas complete all as specified and directed.

M & L reinforced cement concrete M-25 design mix (using 20 mm graded crushed stone aggregate) as in roof slab, beams and columns in floors, roofs, landings, balconies, canopies deck slabs and in shelves and the like complete all as specified and directed.

M&L for formwork to sides of flat concrete foundations, footings, based of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter rough finished surfaces of concrete complete all as specified and directed.

M&L for Formwork to sides of pillars, posts, struts, piers columns Square, rectangular or polygonal etc rough finished surfaces of concrete complete all as specified.

M&L for Formwork to chullah hoods, chajjas and similar items etc flat complete all as specified & directed by Engineer-in-Charge.

M&L for Formwork to sides & soffits of roof beam, lintel beams, bands, cantilivers, shelves flat etc complete all as specified & directed by Engineer-in-Charge.

M&L for Form work to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick etc of rough finished surfaces of flat concrete complete all as specified and directed.

S&F mild steel TMT bars 10 mm dia & over, cut to length bent to shape required, including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F mild steel TMT bars 6 to 8 mm dia , cut to length bent to shape required, including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F mild steel TMT bars 5 mm dia & over upto and including 10 mm dia in stirrups, spacers and binders cut to length bent to shape required, including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on concrete slab surfaces mixed with integral water proofing compound (3% of weight of cement) as per manufacturer's instructions, surfaces finished even and smooth without using extra cement complete all as specified and directed. (Note :- The rate of WPC is deemed to be included in this item).

M&L for cleaning the plastered/concrete surfaces with wire brushes and applying water proofing treatment as under: (a) Apply bitumen primer at the rate of 0.27 litre per Sqm as per IS 3384-1986 and bonding bitumen of VG-10 @1.20 Kg per Sqm. (b) APP modified water proofing memebrane as per IS 16540/16532-2017, 3mm thick and weighing not less than 3.50 kg per Sqm reinforce polyster/HMHDPE matt black finish over compatible primer/bonding bitumen (wt not less than 150 gms/sqm) by forced application and finish the top surface with bituminus aluminium paint @0.10 Ltr per Sqm complete all as specified.

Returning, filling , including spreading, levelling, watering and well ramming in layers not exc 25 cm in Soft/loose soil complete all as specified and directed.

Spreading levelling excavated material in floors in layers n.exc 25 cm thick incl watering and well ramming complete all as specified and directed

Removing excavated material exc 1.5 Km but n.exc 5 Km out side MD land and depositing where directed.

M&L precast cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in block masonry with solid blocks, exc 10 cm in width and setting in mortar complete 1:6 complete all as specified and directed.

M&L for 40 mm thick DPC to horizontal or vertical surfaces including necessary form work in PCC 1:2:4 type B-0 using WPC (3 % of weight of cement) complete all as specified and directed. (Note :- The rate of WPC is deemed to be included in this item).

M & L hardcore of broken stone or boulders of gauge n.exc 63mm deposited spread and leveled in layer n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 100 mm thick cement concrete type D-2 1:4:8 (using 40 mm graded crushed stone aggregate), as in sub base of floors complete all as specified and directed.

M&L 25 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in floors finishing complete all as specified and directed.

M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick on brick work or concrete surface as in ceiling in cement mortar 1:3 and finished smooth and even without using extra cement complete all as specified and directed.

S&F coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

S&F coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including rendering 10 mm thick on fair faces of brick work or concrete surfaces as backing coat in cement mortar 1:4 complete all as specified.

M&L for 75 mm thick, PCC 1:3:6 type C2 (using 40mm graded stone aggregate), finished even and smooth without using extra cement as in plinth protection incl joints filling complete all as specified.

M&L preparing newly plastered surfaces or unplastered on walls etc and applying two coats of cement base paint over a coat of cement base primer complete all as specified and directed.

M&L preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

S&F factory made solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, fixed in the frame at site as specified and directed at site complete all as specified and directed.

S & F 100mm MS butt hinges medium weight cold rolled complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips or sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium ally fixed complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolts and extrude section and fixed complete all as specified and directed.

S&F 150 mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed

S&F Powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. (Thickness or powder coating not less than 50 micron) complete all as specified and directed.

S&F 4.0 mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sqm in each pane.

S&F Rotational moulded polyethylene 1000 Ltrs water storage tanks(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I complete all as specified and directed.

S&F 20 mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S&F 25 mm PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and directed.

S&F 20 mm PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and directed.

S & F of CPVC pipes 25mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including concealed in walls complete all as specified.

S & F of CPVC pipes 20mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S&F 75mm size PVC floor trap with grating incl jointing with solvent cement complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including CI/PVC/Vitreous china 'P' or 'S' trap , 110 mm dia PVC(SWR) WC connector and 75 mm dia pipe required length for Nahani trap along with grating complete all as specifed and as directed.

S&F plastic water closet seat cover, White, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specifed and as directed.

S&F PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action with inlet ball valve and float including flush pipe, handle, bracket PVC short bendetc. complete all as specified and directed .

S&F PVC connection 15 mm size , 45 cm long with PTMT adopter,check nuts and washer on both sides for cold water complete all as specified and directed.

S&F vitreous china white counter top wash hand basin 545x545x185 and including one number brass CP waste coupling, waste pipe 32 mm dia, brackets 2 numbers including cutting for and pinning in ends of brackets etc fixed on granite platform complete all as specified and directed.

S&F 32 mm dia PVC waste pipe for WHB/urinal complete all as specified.

S&F fancy type wall mixture of brass, chromium plated, 2 in 1 system with hot and cold arrangement upto 5th floor of bldgs.

S&F 15 mm bore diameter CP two way bib taps quarter turn with crutch or butterfly handle,screwed down,screwed for pipe or for brass ferrule complete upto 5th floor of bldgs all as specified and directed.

S&F stop valves/Angle valve 15 mm nominal bore, brass, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete, all as specified and directed .

M&L Pre cast RCC (1:2:4) type B1 for cover slab for man holes and set in cement mortar (1:6) complete all as specified and directed.

S&F Glass corner shelf including CP railing, radius 250 mm complete all as specified and directed.

S&F tubular towel rail 600 mm long of brass chromium plated 20 mm dia D type 60 cm long fixed with two plugs (gutties) of 2nd class hard wood embedded in cement mortar 1:3 with MS screws complete all as specified and directed.

S&F 15 mm bore pillar taps, cast copper alloy, fancy type with capstan heads, chromium plated screwed down high pressure with or without lattered 'Hot' or 'Cold' with long screwed for iron pipe and fixed complete all as specified and directed.

S&F Swivel shower rose 15mm of brass chromium plated 150 mm dia round with shower arm of 190mm Long Light Body complete upto 5th floor of bldgs all as specified and directed .

S&F 15 mm bore Fancy type hand shower (Health faucet), ABS chrome plated with 15 mm dia 1.25 meter long flexible tube and wall hook complete all as specified and directed.

S & F Stainless steel toilet paper holder with flap recessed type complete all as specified and directed.

S&F chromium plated soap dish of fancy type fixed with rawl plug & screws to wall of approved make complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

M&L 150 mm dia salt-glazed stoneware drain pipes laid in trenches and jointed as specified

M&L concrete ( 1 : 3 : 6) type C-2 to drain pipes including packing under haunching against sides for 150 mm dia pipe complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Removing building materials to a distance of exc. 1.0 Km but not exc. 5.0 Km (1 Metric tonne = 1 Load and One Cum = 1735 Kgs) out side MD Land Complete all as directed.

M &L providing cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) in lintel upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, stringcourses lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones bed plates,kerbs incl weathering slightly rounded or chemfered angles and throating as directed.

Removing Existing water proofing treatment, including bedding concrete etc complete, cleaning the surfaces with wire brushes, removing dust, foreign material ,scrubbing down with water and rubbish off the same beyond the Defence land.

Material and labour for PCC 1:2:4 type B0(using 12.5mm graded stone aggregate) for but on roof slab as required to fill up the undulations to maintain smooth slope (avg thickness 40 mm.) complete all as specified.

Material and labour for PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) for filleting and benching, slightly rounded or chamfered on edges complete all as specified and directed.

M&L preparation of old steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enemel paint complete all as specified and directed .

Dismantling of old Ceiling/boarding, any description, fixed in any position with nails complete all as specified and directed.

S&F anodised aluminium snap grid frame work for false ceiling, size of grid 605x605mm, complete all as specified and directed.

Hangers 4 mm dia G.I (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long complete all as specified and directed.

M&L 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timer/GI/ Aluminium framework with screws as in ceiling complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing debrits out side the MD land complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified.

Taking down cement plaster on brick or stone walls etc, incl raking out joints, hacking for key scrubbing down with water, etc. complete all as specified and directed.

M&L rendering 15mm thick in CM 1:6 on bricksurfaces finished even and smooth without using extra cement all as specified and directed.

M&L preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion white or tint with priming platered and other surfaces incl 1 mm thick wall care putty on plastered surface complete all as specified.

M&L for preparation ol new plastered surfaces of walls Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

M&L for preparation of old distempered surfaces of walls and applying one coat of Oil emulsion distemper including stopping of nail holes, filling of cracks, etc and cleaning all window panes from splashes / droppings, complete all as specified and directed.

M&L for preparation of old distempered surfaces of ceilng and applying one coat of oil bound distemper all as including cleaning splashes of distmeper on floor/objects etc complete all as specified and directed.

M&L for Preparation of Old surfaces of wall and Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm complete all as specified and directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frame) exc 1.5 sqm but n.exc 4 Sqm complete all as specified and directed.

Taking down Shutters of any description n exc 1 sq. m each complete all as specified and directed.

S&F second class hard wood 30 mm thickPlain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 4.0 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane complete all as specified.

S&F stainless steel 100 mm butt hinges for doors complete all as specified.

S&F 150 mm size extruded aluminium alloy handles fabricated type anodized complete all as specified.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified..

S&F 150 mm long floor door stopper of aluminium alloy body and tongue,anodised,with hard drawn steel spring complete all as specified.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples complete all as specified.

M&L preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

M&L Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work in cement mortar 1:6, complete all as specified and directed.

M&L Making good under cills or over arches, lintels and bres?summers. including all?pinning when necessary in ncement mortar 1:6 complete all as specified and directed.

S&F in repairs 100 mm long Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all specified and directed.

S&F in repairs 150 mm size extruded aluminium alloy handles fabricated type anodized complete all as specified and directed.

M&L Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

M&L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed .

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi?chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Demolition of Reinforced Cement Concrete of tank Incl removal of Dabris from MOD land complete all as specified.

M&L 100mm thick PCC (1:2:4) Type B-0 (using 12.5 mm graded stone aggregate) as in floor for tank plateform complete all as specified.

S&F 2000 ltrs capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top)vhoilsted and fixed in position all as specified in SSR Part-I complete all as specified & directed by Engineer-in-Charge.

S & F of CPVC pipes 25mm Incl. SDR 11 Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down of existing pipe any type complete all as specified.

S & F of CPVC pipes 20mm Incl. SDR 11 Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down of existing pipe any type complete all as specified.

S&F in repairs 25 mm float valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as Specified

S&F 25mm Nipple suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm- 45gms /25mm- 65gms complete all as specified.

S&F of 25 mm dia male brass threaded adapter complete all as specified and as directed.

S&F of 25 mm dia female brass threaded adapter complete all as specified and as directed.

Supplying and laying of CPVC ball valve 25mm dia complete all as specified.

Supplying and laying of CPVC Union 25mm dia complete all as specified.

M&L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over a screed of 15mm thick in CM 1:6 complete all as specified and directed.

S&F Coloured glazed ceramic tile in vertical surface 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick rendering CM 1:4 backing coat after dismantling of wall tiles/Terrrazzo/Stone Slabs/ or any type of materials in dado including cement mortar bedding complete all as specified and as directed.

M&L 18-20 mm thick Granite black colour including rounding edges to exposed portion as in platforms for wash hand basin / sink (table, rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like laid in cement mortar (1:4) incl pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade granite including cutting for securing of slab laid over existing any type of stone or concrete etc complete all as specified and as directed.

Taking down steel windows glazed and gauged with guard bars exc. 0.5 sqm and not exc. 1 Sqm each and incl. all fittings and fixtures and removed from site and disposed off outside MD land after measurement, entry in MB as Sch of credit material and signature by both parties complete all as specified and directed. (Both glazed and gauged windows will be measured separately)

Taking down or detaching old MS grill by cutting and refixing in the same location incl. all necessary arrangement and T&P by contractors own arrangement of size exc. 0.5 sqm and not exc. 1 Sqm each with PCC (1:3:6) type C-1 using 20mm graded stone aggregateand incl. all fittings and fixtures and removed from site and disposed off outside MD land after measurement, entry in MB as Sch of credit material and signature by both parties complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for ventilators with extruded built up standard rectangular/square section including PVC strips for holding of louvers of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. complete all as specified.

S&F 4mm thick figured glass pin headed type and glazing with oil putty in square n.exc 0.50 Sqm in each pane complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5 sqm etc complete all as specified and directed.

S&F Factory Made single extruded WPC (Wood polymer composite) solid door/windows and other frames / chowkats of size 65mm x 100mm single rebated comprising of virgin PVC polymer of K value 58-60 (SuspensionGrade) calcium carbonate and natural fibres (Wood powder/rice husk/wheat husk) and Non-toxic additives (Maximum toxicity index of 12 for 100 gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws withdrawal strength of 2200 N (Face) and 1100 N (Edge) minimum compressive strength of 58 N/Sq mm, modulas of elasticity 900 N/Sq mm and resistance to spread flame of Class A category with property of being termite / borer proof, water/moisture proof and fire retardant and fixed in position with MS holdfast/lugs/SS dash fasteners of required dia and length complete as per direction of Engr-in-Charge. (MS holdfast/lugs or SS dash fastener shall be paid for separately)

S&F Factory Made solid PVC moulded door shutter 28 to 30mm thick (Stiles) with 2, 4, 6 raised panels design with 2mm thick moulded prelam PVC sheet on the front and back face with particle board core and fixing in the frame at site as per specification and drawings.

S&F stainless steel 75 mm butt hinges for doors complete all as specified.

S&F Factory Made single extruded WPC (Wood polymer composite) solid door/windows and other frames / chowkats of size 65mm x 125mm double rebated comprising of virgin PVC polymer of K value 58-60 (SuspensionGrade) calcium carbonate and natural fibres (Wood powder/rice husk/wheat husk) and Non-toxic additives (Maximum toxicity index of 12 for 100 gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws withdrawal strength of 2200 N (Face) and 1100 N (Edge) minimum compressive strength of 58 N/Sq mm, modulas of elasticity 900 N/Sq mm and resistance to spread flame of Class A category with property of being termite / borer proof, water/moisture proof and fire retardant and fixed in position with MS holdfast/lugs/SS dash fasteners of required dia and length complete as per direction of Engr-in-Charge. (MS holdfast/lugs or SS dash fastener shall be paid for separately)

S & F factory made 30mm thick wire gauged i.e. panel will be of wire gauge single side prelam PVC sheet panel consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. The wire gauge shall be wrapped on an additional square 8mm MS solid tube and this tube shall be welded to MS tubs. The wire gauge shall be stretched to tighten firmly and fixing in the frame as per specification and drawing.

S&F mild steel 150 mm helical door springs including roller and roller plate complete (Helical door spring) including welding to steel chowkhats if required all as specified.

S & F bands, straps, supports or stays for rainwater, ventilating pipes including bolts if required, hooks (Stay) heavy for large gate, clamps, holdfasts, wall ties, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165.

S&F of 20mm dia CPVC brass elbow complete all as specified and as directed.

S&F of 20mm dia CPVC Brass Tee complete all as specified and as directed.

S&F of 20mm dia female/male brass threaded adapter complete all as specified and as directed.

S&F of 15 mm CP extension nipple complete all as specified and as directed.

S & F in repair PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls fixed with PVC straps or clips including dismantling and breaking of pipe and fittings complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 75 mm size in bore single socketed , in any length with rubber ring joints, fixed to walls fixed with PVC straps or clips including dismantling and breaking of pipe and fittings complete all as specified and as directed.

S&F in repair PVC (SWR) 110 mm bore pipes single socketed, in any length with rubber ring joints laid in floors including dismantling and breaking of pipe and fittings complete all as specified and as directed.

S&F in repair PVC (SWR) 75 mm bore pipes single socketed, in any length with rubber ring joints laid in floors including dismantling and breaking of pipe and fittings complete all as specified and as directed.

S&F in repair PVC bends any radius 75mm dia complete all as specified and directed.

S&F in repair PVC bends any radius 75 mm dia with access door complete all as specified and directed.

S& F in repair PVC bends any radius 110mm dia complete all as specified and directed.

S&F in reapir PVC bends any radius 110 mm dia with access door complete all as specified and directed.

S&F in repair PVC Single T any radius 110 mm dia complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) 'P' or 'S' trap including dismantling of old Water closet complete all as specifed and as directed.

S&F in repairs plastic water closet seat cover, White, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specifed and as directed.

S&F in repair PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action with inlet ball valve and float including flush pipe, handle, bracket PVC short/long bendetc. complete all as specified and directed

S&F in repair PVC connection 15 mm size 60 cm long with PTMT adopter,check nuts and washer on both sides for cold water complete all as specified.

S&F in repair vitreous china oval type countertop wash hand basin, white of size 560 x 400 x 205mm including one number brass CP waste coupling, waste pipe 32 mm dia complete all as specified and directed.

S&F Glass corner shelf including CP railing, radius 300 mm complete all as specified and directed by the Engr-in-Charge, fixed in repairs.

S&F in repairs Bib tap cast copper alloy 15mm fancy type Chromium plated screwed down, high pressure, with capstan head screwed down screwed for iron pipe.

S&F pillar taps, brass, with capston heads, fancy type, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed in repair complete all as specified and directed.

S&F in repairs angle valves 15 mm nominal bore, brass, chromium plated, complete, fixed in repairs, all as specified and directed .

S&F,in repairs 15mm size health faucet, ABS body with wall hook and 1 metre stainless steel braided rubber hose pipe complete all as specified and as directed.

S&F in repairs brass chromium plated grating 125 mm dia circular with centre hole/ without hole of approved make and fixing with cement mortar 1:3 on Nahani trap or floor trap complete all as specified.

S&F in repairs 75mm dia PVC (SWR) floor/Nahani trap, plain with grating including solvent cement with dismatnling of old nahani trap with necessary PCC/ cement work complete all as specified and as directed.

S&F in repairs two way quarter turn Bib tap cast copper alloy 15mm fancy type Chromium plated screwed down, high pressure, with capstan head screwed down screwed for iron pipe.

S&F welded steel wirefabric n.exc. 4 Kg/sqm

M&L one coat of whitewashing to internal surfaces of walls after preparation of old decorated surfaces of walls after preparation of surface complete.

M&L one coat of whitewashing to internal surfaces of ceilings after preparation of old decorated surfaces of ceilings after preparation of surface complete.

Cutting out concrete blocks, brickwork or stone masonry (in alternate coarse) forming toothings for and bonding new work in mortar into old work including new materials entering in walls of precast concrete in PCC 1:3:6 Type C-1 using 20mm graded stone aggregate set in cement mortar 1:6.

M & L providing precast cement concrete in lintels in RCC 1:2:4 Type B-1 using 20mm graded stone aggregate with plain fair faces, including chamferes, weatherings, throating etc. and setting in cement mortar 1:6 complete with joints to match complete all as specified and as directed.

S&F in repair vitreous china squatting plate urinal white , bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and as directed.

M & L Reinforced Cement Concrete 1:1 1/2 :3 Type A-1 using 20 mm graded crushed stone aggregate in foundations including rafts, footings and mass concrete complete all as specified and as directed.

M & L Reinforced Cement Concrete 1:1 1/2 :3 Type A-1 using 20 mm graded crushed stone aggregate) in columns complete all as specified and as directed.

M & L Reinforced Cement Concrete 1:1 1/2 :3 Type A-1 using 20 mm graded crushed stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

Reinforced Cement Concrete1:1 1/2 :3 Type A-1 using 20 mm graded crushed stone aggregate) in slab supported on walls and beams and shelves like complete all as specified and as directed.

Reinforced Cement Concrete1:1 1/2 :3 Type A-1 using 20 mm graded crushed stone aggregate) in chajjas complete all as specified and as directed.

Use and waste for from work to edges of concrete slab

S&F Powder coated anodised aluminium frame, for door, windows, ventilators runner & packing with rubber gasket etc, with one or more rebates including joinning cleat for rebates including joining cleats for fixing etc, complete all as specified & directed by Engineer-in-Charge.

S&F solid door frame of size 50 x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, supplying and fixing in opening as per specification & drawing complete all as specified and as directed.

S&F Powder coated anodised door shutter aluminium section nex weight 0.55kg Per/RM including necessary jointing cleats glazing clips, rubbgr neoprene handles 2Nos each door hinges alumn anodised snapveding screws etc..Complet all as specitied

S&F 9mm thick prelaminated particle bord both side with decorative choies lamination

M & Lfor powder coated Aluminium windows of three tracks outer frame,top,side section ,bottom frame( track) with guide track of size 92.5x31x1.50 mm with sliding window shutter 2 nos with glass and one nos with wire mesh9 total 3 nos shutter) from top and side section bottom section with wheel track and inner locking section of size 40x18x1.5 mm including glass 4 mm thick and aluminium wire cloth 0.45 mm nominal dia wire and average width of aperture 1.40 mm complete all as specified and directed

S&F 100 mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified and as directed .

S&F mild steel butt hinges 75 mm, medium weight cold rolled and fixed complete all as specified and as directed.

M&L for rendering 5 mm thick CM 1:4, over 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound at the rate of 3% of weight of cement finishing the surface fair and even complete all as specified and as directed. Note: Rate of water proofing compound is deemed to be included in this item.

M & L 25mm thick PCC (1:2:4) Type B-0 using 12.5mm graded stone aggregate as in sub-base of floor

M & L 75 mm thick Cement concrete type D2, 1:4:8 (using 40 mm graded crushed stone aggregate) in sub base of flooring/ hard standing complete all as specified and as directed.

M & L 50 mm thick PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) in floorings including finishing the surface even and smooth using without extra cement complete all as specified and as directed.

S & F ultra charged Vitrified coloured ceramic tiles ( light shade) 8-9 mm thick ( Square/rectangular) polished area of each tiles not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white /coloured cement to match over a screed bed of 15 mm thick in CM 1:6 etc complete all as specified and as directed.

S & F ultra charged Vitrified coloured ceramic tiles ( light shade) 8-9 mm thick ( Square/rectangular) polished area of each tiles not exc 0.36 sqm in skirting etc set and jointed in neat cement slurry and pointed in white /coloured cement to match over a screed bed of 10 mm thick in CM 1:4 etc complete all as specified and as directed.

M&L for preparing newly plaster surfaces of walls and applying two or more coats of Premium acrylic emulsion weather coat UV resistant Alkali & fungal resistance, dirt resistance exterior paint of Make-APEX Ultima from Asian paints/ Berger weather coat All guard/Dulax weather shield m Max/Nerolax Excel top guard and must have an interval of 4 to 6 hours between the 1st and 2nd coat of approved shade ( company depot tinted) over one coat of elastomeric exterior weathe coat primer @0.90 litre/10 sqm incl all necessary safety norms to the workers complete all as specified and as directed.

S&F vitreous china wash hand basin, white, flat back size 550 x 400 mm including one number brass CP waste coupling, waste pipe 32 mm dia, brackets 2 numbers including cutting for and pinning in ends of brackets complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor/Nahani trap, plain with CP grating including solvent cement complete all as specified and as directed.

S&F 110mm dia PVC (SWR) 'P' trap complete all as specified and as directed.

S & F 100mm dia PVC (SWR) bends with oval access door

S & F 75mm dia PVC (SWR) bends with oval access door

S & F 110mm dia PVC (SWR) reducers

S & F 75mm dia PVC (SWR) vent cowls

S&F 500 Ltrs. Capacity rotational moulded polyethylene water storage tanks (cylinder vertical with class top) hoisted and fixed in position complete all as specified

S & F 20 mm dia CPVC ball valves complete all as specified.

S&F CPVC pipes SDR 11 & plain CPVC SDR 11 fittings of 16mm dia laid on walls / ceiling or laying in floors complete all as specified.

S & F 20mm brass tank adaptor

S & F 15mm brass elbow

S & F 15mm brass Tee

S & F 15mm brass male threaded adaptor

S & F 15mm brass female threaded adaptor

M & L PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in benching of manholes, coping including forming centre channels half round or 1/4 section complete all as specified and as directed.

Extra for forming fair finished channel or drain 30cm girth (inner girth) in cement concrete using extra cement including forms, moulds stopped complete all as specified and as directed.

M & L for laying of DWCPE sewage pipes line 200mm dia bore of pipe incl sealing of joints fittings etc complete with collars complete all as specified and as directed.

M & L concrete 1:3:6 type C2 to drain pipes including packing and under surrounding pipes with concrete after they are laid and tested for 200mm dia pipe complete all as specified and as directed.

S & F readymade 8 feet pulley operated cloth drying system, aluminium anodised 22mm outer dia pipe, channel assembly, locking system to hide rope knot, ropes 4mm dia polyster braided undiyed & fitting material etc complete all as specified and as directed.

M & L for point wiring with 1100 volts grade 1.5 Sqmm PVC FRLSH unsheathed cable multistranded copper conductor conforming to IS 694 : 1990 (for phase, Neutral and Earth) including 1.5 Sqmm PVC insulated unsheathed copper conductor as earth continuity conductor drawn including Non metallic PVC rigid conduit medium grade with ISI marked all accessories concealed in wall / ceiling / floor / road etc with cast iron / pressed steel terminal box of suitable size duly painted inner and outside by anticorrosive paint, including plastic laminated sheet 1.6mm thick mounting switches, socket cover with fitting screw washer, including cutting chasses in wall / floor / roof for fixing of conduit and making good the disturbed surfaces matching with existing etc complete all as specified and as directed.

One light point controlled by one switch complete all as specified and as directed.

One fan point controlled by one switch complete all as specified and as directed.

One 3 pin 5 Amps socket out let point on independent board complete all as specified and as directed.

One switch / 3 pin 5 Amps socket out let point on same board complete all as specified and as directed.

M & L switch piano, flush type single pole, one way 5 Amps complete all as specified and as directed.

M & L switch socket outlet 2 in 1, 3 pin 5A complete all as specified and as directed.

M & L Ceiling rose surface bakelite 65 x 50mm two to three terminals complete all as specified and as directed.

S & F MCB DB double door type, made out of CRCA mild steel sheet flushed in wall, SPN 12 way with 200 Amps rated bus bar, 240 volts, IP 43 with PVC MCB blanking plate stove enamelled dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and as directed.

S & F MCB SPN 6 - 40 Amps, 240 volts complete all as specified and as directed.

S & F in repairs MCB SP 6-40 Amps AC 240 volts complete all as specified and as directed.

All as per item No 218 above but with 2.5 Sqmm wire for power point concealed in wall / ceiling suitable for 3 pin 15 Amps socket outlet on independent board complete all as specified and as directed.

M & L Sub main wiring surface type with two runs of single core, PVC insulated, unsheathed multi stranded copper conductor cable of size 4 Sqmm, 1100 volts grade (FRLS) and one run of 4 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through casing caping / existing conduit as required complete all as specified and as directed. Note : Two runs of 4 Sqmm cable, one run of 4 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length.

S & F surface mounted Mini Mirror light LED batten 2 feet with extruded aluminium housing and robust construction 10W system lumen with all accessories if required flexible copper 2 core wire from fitting to ceiling rose complete all as specified and as directed.

S & F surface mounted Mini Mirror light LED batten 4 feet with extruded aluminium housing and robust construction 20W system lumen with all accessories if required flexible copper 2 core wire from fitting to ceiling rose complete all as specified and as directed.

S & F PVC body sound proof Exhaust fan 300mm size made of study engineering plastic complete with single phase 230 volt with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper widing of sweep 300mm complete, making a hole in wall or existing window grill cutting and 12mm plywood suitable size of exhaust fan make hole and fixing the window nuts, bolt, washers and after finishing work disturbed surface of wall complete all as specified and as directed.

S & F LED Bulkhead light fitting 10watt environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge lit LED luminaire comprising of high brightness LEDs including connection of flexible copper wire 2 core from fitting ceiling rose / connection point complete all as specified and as directed.

S & F electric water heater, storage type, steel body with copper inner tank and heating element upto 2KW capacity 25litres, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe etc and including connecting up with three core copper conductor cable with 15AMps plug top complete all as specified and as directed.

Taking down copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling rose, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc.

M & L switch piano, flush type single pole, one way 15 Amps complete all as specified and as directed.

M & L switch socket out let 2 in 1, 3 pin 15A complete all as specified and as directed.

S & F fan regulator step type 120W modular type complete all as specified and as directed.

M & L Sub main wiring surface type with two runs of single core, PVC insulated, unsheathed multi stranded copper conductor cable of size 6 Sqmm, 1100 volts grade (FRLS) and one run of 6 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through casing caping / existing conduit as required complete all as specified and as directed. Note : Two runs of 6 Sqmm cable, one run of 6 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length.

S & F in repairs MCB DB double door type, made out of CRCA mild steel sheet flushed in wall, SPN 8 way with 200 Amps rated bus bar, 240 volts, IP 43 with PVC MCB blanking plate stove enamelled dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and as directed.

S & F in repairs MCB SPN 63 Amps, 240 volts complete all as specified and as directed.

S & F in repairs surface & wall mounted LED batten 4 feet with extruded aluminium housing and robust construction 20W system lumen including flexible copper 2 core wire from tube light fitting to ceiling rose required length with all accessories complete all as specified and as directed.

S & F in repairs LED recess / surface mounting as required 2 x 2 fitting 600mm x 600mm, 35/36 watt, 220V AC recessed type with diffuser glare free light complete with driver , holders & LED lamp of suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

Taking down ceiling fan of any size / capacity / type from existing position and deposit to MES store yard after cleaning to refixing the same as per existing complete all as specified and as directed by the Engr-in-Charge.

S & F LED weather proof bulk head light fitting of shape and size as per site requirement of wattage upto 10 watt light fitting with, mounting clamp, LED driver holder, LED lamps etc including connecting up to ceiling rose complete all as specified and as directed.

S & F ceiling fan 1200 mm sweep with BLDC electric motor having star rated service wire 6.0 cubic meter per minute / watt, single phase with operating voltage range 140 to 285 volts BEE 5 star rated including mounting arrangement, 3 core flexible copper conductor cable upto ceiling rose, down rod suitable size length etc complete all as specified and as directed.

S & F PVC body sound proof Exhaust fan 250mm size made of study engineering plastic complete with single phase 230 volt with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper widing of sweep 250mm complete, making a hole in wall or existing window grill cutting and 12mm plywood suitable size of exhaust fan make hole and fixing the window nuts, bolt, washers and after finishing work disturbed surface of wall complete all as specified and as directed.

M & L earthing complete with GI earth plate Electrode 60cm x 60cm x 6mm thick burried directly in ground (earth plate not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level connected to galvanised earth wire 4.0mm dia by means of bolts, nuts check and washers of GI or steel all as shown in electrical plate No 3 of SSR Part I connected to earthing test point all as specified or indicated including GI pipe 15mm dia light grade for earth wire protection, necessary excavation, earth work in any type of soil, PCC chamber and RCC cover slab, connecting lead wire from test point to DB complete all as specified and as directed.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded galvanished steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 Sqmm x 4 core complete all as specified and as directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M & L for sand cushioning in trenches for bricks of UG cable with coarse sand laid dry in trenches with uniform thickness complete all as specified and as directed.

Supply and lay burnt bricks of sub class 'B' laid dry across in trenches for cable protection all as specified and as directed.

Supply and laying 20mm GI pipe fitting tubes medium grade galvanished with all fittings complete laid in trenches complete all as specified and as directed.

S & F of float valve of size 20mm and as required at site as complete brass fitting with rod and plastic ball complete all as specified and as directed.

S & F gun metal gate valve with inner wheel head, screwed both ends in iron ppe and fixed of size 20mm complete all as specified and as directed.

Elite Constructions (BID ID -3223904)

PRAGATHI BUILDERS (BID ID -3217005)

K. VENKATESH NAIDU (BID ID -3223575)