Development of Waterfront and Replicating the Armar Kendra at Naglabander Creek within Thane Municipal Corporation Limit.

Amount

Labour charges for removing grass, thorny shrubs, Jungli shrub, Kubabul and alike grass along roadside making the ground clean by shovel and phavaras etc. complete.

Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts up to a lead of 50m. and spreading for embankment or stacking as directed.

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/ murum watering, ramming etc. complete. (Lift upto 1.5 m). By Mechanical Means

Removing sand /muck/ slush /soil bellow low tide level to the specified section from navigation channel as per the area and depth upto 3.00 m from sea bed by mechanical means with , hydraulic excavator, etc. and barge for establishment all machinery with all required tools and equipment, boat for conveying excavated material, including removing the excavated materials with all lift and leads as directed beyond high tide level line of water stacking spreading or disposing, dewatering if required unless otherwise provided else where complete under tidal condition.

Providing earth work in embankment with approved materials obtained from departmental land upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing to the required lines, curves, grades & section, watering and compaction with vibratory roller to achieve not less than 97 % of standard proctor density etc. complete ( Material obtained from departmental Land)

Providing earth work in embankment with approved materials obtained from other sources upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing to the required lines, curves, grades & section, watering and compaction with vibratory roller with V-Sat attachment to achieve not less than 97 % of standard proctor density etc. complete ( Material obtained from Other sources)

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Providing rubble filling of trap/ granite/ quartzite gneiss stones for foundations including filling voids with sand/grit and compaction etc complete. (In Tidal Condition)

Providing dry rubble stone pitching 23 cm (about 9 ) thick including all material, quarry spalls, labour etc. complete.

Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etc. complete.

Providing and Laying factory made coloured chamfered edge Cement concrete grass paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine aggregate (natural sand/crushed sand VSI grade finely washed etc.), compacting and proper embedding/laying of inter locking paver blocks into the fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and cutting of paver blocks as per required size and pattern, finishing and sweeping extra fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and complete as per manufacturer specifications & direction of Engineer-in-Charge. 60mm thick CC paver block of M-35 grade concrete with approved colour and design & pattern.

Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthen bunds etc. as may be necessary for foundation and other parts of the works and pumping out water during and after excavation as may be required by using 5.0 to 9.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary)

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel cantering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel cantering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centring will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) With Additional 10% of Tidal Condition

Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction and roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Lift from 3.8m to 7.6m

Lift from 7.6m to 11.5m

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Lift from 3.8m to 7.6m

Lift from 7.6m to 11.5m

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork,cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Lift from 3.8m to 7.6m

Lift from 7.6m to 11.5m

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap /granite / gneiss/ quartzite metal for R.C.C. arches with skew backs as per detailed design and drawings or as directed including steel centering, plywood/steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement, including cover block). Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying cast in situ / Ready Mix Cement Concrete M-30 for bored piles each of load capacity and as per design and of 500mm diameter or as directed placed through steel shells sunk to the required depth through all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in- charge including placing with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell etc. complete. (Excluding steel reinforcement)

Providing and laying cast in situ / Ready Mix Cement Concrete M-30 for bored piles each of load capacity and as per design and of 750 mm diameter or as directed placed through steel shells sunk to the required depth through all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in- charge includingplacing with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell etc. complete. (Excluding steel reinforcement)

Providing and laying cast in situ / Ready Mix Cement Concrete M-30 for bored piles each of load capacity and as per design and of 900 mm diameter or as directed placed through steel shells sunk to the required depth through all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in- charge includingplacing with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell etc. complete. (Excluding steel reinforcement)

Providing and laying cast in situ / Ready Mix Cement Concrete M-30 for bored piles each of load capacity and as per design and of 1000 mm diameter or as directed placed through steel shells sunk to the required depth through all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in- charge includingplacing with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell etc. complete. (Excluding steel reinforcement)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap metal for R.C.C. pile caps as per detailed designs and drawings, including bailing out water manually, centering, formwork, laying/ pumping, compacting, finishing and curing etc. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) complete.

Chiseling through pile shells in hard strata like boulders, soft and hard rocks Upto and inclusive of 550 mm diameter including removing and stacking the loose materials etc. complete and disposing of the unserviceable materials outside complete.

Chiseling through pile shells in hard strata like boulders, soft and hard rocks Beyond 550 mm and upto and inclusive of 750 mm dia. including removing and stacking the loose materials etc. complete and disposing of the unserviceable materials outside complete.

Chiseling through pile shells in hard strata like boulders, soft and hard rocks Beyond 750 mm and upto and inclusive of 900 mm dia including removing and stacking the loose materials etc. complete and disposing of the unserviceable materials outside complete.

Chiseling through pile shells in hard strata like boulders, soft and hard rocks Beyond 900 mm and upto and inclusive of 1050 mm dia. including removing and stacking the loose materials etc. complete and disposing of the unserviceable materials outside complete.

Providing placing and Driving in position 6 millimeter mild steel liner for R.C.C. Piles upto required depth with 12mm thick mild steel cutting edge of 0.50m length at bottom including fabricating cutting the mild steel sheet to required diameter and shape ,welding the joints and driving with the help of required machineries including all materials labours and lifts etc. complete as directed by the Engineer in charge. Spec :(As directed by Engineer in Charge From 3.00 to 9.50 meter deep liner

Chipping and dressing of the R.C.C. piles upto 0.60 meterincluding cleaning reinforcement and removal of dismantled materials upto a distance of 50 meter beyond the building area etc. for providing pile caps. Spec :(As directed by Engineer in Charge

Empty boring for 425 to 500 mm dia. bored R.C.C. cast in situ piles including withdrawal of shell, removal of earth to a distance of 50 metres etc. complete.Spec :(As directed by Engineer in Charge)

Empty boring for 725 to 1050 mm dia. bored R.C.C. cast in situ piles including withdrawal of shell, removal of earth to a distance of 50 metres etc. complete.Spec :(As directed by Engineer in Charge)

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Lift from 3.8m to 7.6m

Lift from 7.6m to 11.5m

Providing uncoursed rubble masonry of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in foundation and plinth of inner walls / in plinth of external walls including bailing out water manually , striking joints on un exposed faces and watering etc.complete.

Providing uncoursed rubble masonry of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in superstructure including racking out joints when plastering is to be done / striking joints when no plastering is to be done on inside watering and scaffolding etc.complete.

Lift from 3.8m to 7.6m

Lift from 7.6m to 11.5m

Providing coursed rubble masonry second sort of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in superstructure including raking out joints when plastering is to be done and striking joints when no plastering is to be done on the inside, watering scaffolding etc.complete.

Lift from 3.8m to 7.6m

Lift from 7.6m to 11.5m

Supply and laying of gabion facia with 2m integrated tail as secondary reinforcement for Reinforced soil system as per MoRTH Clause 3100, made of Mechanically Woven Double Twisted Hexagonal Shaped Wire Mesh , Mesh Type 10x12, Zn + 10% Al +Polymer coated Mesh Wire dia. 2.7/3.7mm (ID/OD), mechanically edged / selvedged, with partitions at 1m interval and shall have minimum 10 numbers of mesh openings per meter of mesh perpendicular to twist, tying with lacing wire of dia 2.2/3.2 mm (ID/OD), supplied @ 5% by weight of facia unit , as per detailed specification conforming to codes in vogue all complete (Backfilling is excluding)as per directions of engineer-in-charge.

Providing & fixing G.I. wire Gabions coated with Zinc+PVC of required size, section including boxes made of mechanically woven hexagonal shaped wire mesh of type, 10x12cm. edges mechanically selvedged made of heavily (Zinc+ PVC) coated G.I. wires as per BS: 443, mesh wire 3.00 mm Ø edge wire 3.9 mm Ø and filled with 20 to 50 kilogram weight trap stones including conveying with all the leads & lifts and placing at required places in required line, level, slope as per drawing, section as directed etc. complete under tidal conditions.(e) Gabions of size – 4.00 x 1.00 x 1.00 M

Supply and installation of Mechanically Woven Double Twisted Hexagonal Shaped Wire Mesh 0.3mthick Gabion(Maccaferri make or equivalent) Boxes ,width 2m, of required sizes, Mesh Type 6x8, Zn+ Al + Polymer coated, Mesh Wire dia. 2.2/3.2mm (ID/OD), mechanically edged / selvedged , with partitions at every 1m interval and shall have minimum 10 numbers of mesh openings per meter of mesh perpendicular to twist, tying with lacing wire, supplied @ 5% by weight of gabion boxes ,as per detailed specification conforming to codes in vogue all complete as per directions of engineer incharge.(With Tidal condition)

Supplying and laying of high strength flexible geogrids (HSFG) as soil reinforcement / basal reinforcement made of high tenacity polyester core with polyethylene coating with Minimum Long Term Design Strength (LTDS) indicated below for 120 years design life at 20 degreeC. The LTDS should be strictly based on reliable test data and performance data available with the manufacturer from accredited independent agency certifying the Reduction Factor (RF) value for their geogrid for design temperature. The geogrid manufacturer should have creep test data from independent accredited laboratory for period over 5 years and should have minimum roll width of 4.5m with core of MS steel tube convenient for handling and lifting work as per detailed specification all complete as per directions of Engineer in charge. (Reference MoRT&H 3100 & IRC 113).High strength geogrid of Long Term Design Strength 59.5 kN/m

Providing and filling in the foundation with artificial sand of approved quality including watering, compacting etc. complete. (To be executed with prior approval of Superintending Engineer)

Providing and laying CE Marked Needle Punched and Mechanically Bonded Non-Woven Geotextile (TechGeo) indigenously manufactured from high quality polypropylene staple fibres (continuous filament will not be accepted) of Techfab India on the prepared subgrade for separation, drainage & filtration application with necessary overlaps as per drawing etc. complete. (Specification: MORTH Section-700 ) with prior approval of concerned Superitending Engineer.c) TFI TECHGEO PR-30 (With Tidal condition)

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972)

Lift from 3.8m to 7.6m

Providing waterproof plaster in W.C. and bath 20 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing (and filling joints of Nahani trap and any outlet by properly) etc. complete.

Providing internal cement plaster 20mm. thick in Single coats in cement mortar 1:3 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete.

Providing vee pointing with cement mortar 1:3 for stone / Brick masonry including scaffolding and curing etc. complete

Providing and fixing bituminous pad 25mm thick for expansion joints in retaining wall, compound wall etc. complete.

Providing and fixing 25mm diameter steel anchor dowel in hard rock including drilling hole of 32 mm diameter up to 0.75 mtrs depth, placing the dowel in position and effectively grouting the hole with CM 1:1 proportion etc. complete.

Random rubble masonry with hard stone in superstructure above plinth level , including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) at window sills, ceiling level and the like.Cement mortar 1:6 (1 cement : 6 coarse sand) Extra for random rubble masonry with hard stone in square and rectangular pillars

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases(NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram/15 l). plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufacturer. The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist.

Providing and applying protective paint consisting of two coats of coal tar epoxy paint over one coat of primer of approved quality and make to the external surfaces of concrete structures to be buried under the soil etc. complete as specified and directed.

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete.

Providing and fixing frame with / without ventilator of size as specified with Country non teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete.

Providing and fixing Country cut teak wood double or single leaf second class fully panelled door shutter with 35mm thick style and rail with 25 mm thick panels with openable fan light as per detailed drawings. Excluding the door frame 60mm x 100mm stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats. (Excluding the door frame)

Providing and fixing in position, Single shuttered aluminium extruded powder coated openable door of overall size 0.90 m x 2.40 m with aluminium door frame of powder coated section 101.60 x 44.75mm , 3.18 mm thick and shutter comprising of powder coated section having bottom and lock rail of size 150 mm x 44.5 mm x 3.00 mm thick top rails 47.62 x 44.45 mm x 3.00 mm thick , vertical style 47.62 x 44.45 mm, 3.00 mm thick and for shutter plain glass panes 5 mm thick for top panels and 12mm thick both side laminated phenol bonded particle board panels for bottom panels etc. , I.S.I. mark , with bijagiri having heavy duty concealed lock, necessary beading, glazing clips, PVC gaskets, 250mm length tower bolts, 150mm diam. pad handle, etc. as per detailed design and drawing or as directed by engineer in charge including all materials , labours, and equipment etc. complete

Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/One Running Metre. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 Kilogram/One Running Metre.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/One Running Metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weight o.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineer incharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising with box

Providing and fixing in position aluminium openable window of any size as per detailed drawing and as directed by Engineer in charge with all necessary aluminium sections including necessary fixtures and fastening with 5 mm thick clear float glass etc. complete. a) With colour anodizing Note While arriving at the rate of item of item weight at 6.90 Kilogram/ One Square Metre is considered.

Providing and laying Polished Kota stone flooring With Hand-Cut Polished Kota Stones 25mm to 30mm thick and required width in plain/diamond pattern on bed of 1:6 Cement mortar including cement float, filling joints with neat cement slurry, curing, cleaning and Mirror Polishing etc. complete Note- Water absorption for kota stone should not exceed 0.05%.( Item to be used with prior permission of Superintending Engineer )

Providing and laying vitrified matt finish tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete.

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.

Supply & Fixing of Rock / Stone Finished outdoor vitrified flooring Tiles 16 mm thick and required width wide in plain pattern including Cement float, filling joints, with neat cement slurry, Natural sand, curing and cleaning complete. with prior approval of concerned Superintending Engineer.

Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm to 8 to 10mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete.

Supply & Fixing of Full Body Vitrifid Step tiles Ready to install Treads and Risers 16 mm thick, required width and required finish in plain pattern including Cement float, filling joints, with neat cement slurry, Natural sand, curing and cleaning etc complete. with prior approval of concerned Superintending Engineer.

Providing 25 mm to 30 mm thick partition of polished black kadappa stone slab of approved quality including giving required size and shape etc. Fixing in cement mortar1:3 curing and cement etc. complete. a) One side polish

Providing and laying in place 300mm x 300mm x 16mm cement tactile directional and warning tiles (for a person with visual impairment)of the approved brand and make and specified colour for outdoor floors such as footpath, courtyard, multimodal location etc. laid on 20mm thick base of cement mortar 1:4 (1 cement: 4 coarse sand) in all shapes and patterns including grouting the joints with white cement with matching pigments etc. complete as per direction of engineer in charge

Providing leather finished polishing to Kota / Marble / Shahabad / Kadappa Stone slab by continuous grinding in 4 coats of different bits to receive rough and matty finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete.

Providing and Fixing Vertical Blinds of approved Make and shade of 100mm regular fabric with powder coated aluminium channel with telting PVC chain & bottom weight plate with all necessary fixtures and fitting etc. complete. (Sample to be final by Engineer In-charge prior execution of work)

Medium Height Steel Storage 750Lx450Dx1200HT Providing and fixing Openable Steel Storage of 750 x 450 x 1200Ht, with 2 adjustable shelves, Complete body & shutter made in 0.8 mm thick & Top in 2 mm thick CRCA, 2 Shutter to be mounted with the help of cup hinges, and 4 adjustable levelers, enitre storage in powder coated finish with 60 to 80 microns. with 25 mm. thk. as per drawing.

3 DRAWER PEDESTAL UNIT @ 392L x 450D x 680Ht. mm.3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. 3 Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board.

WOODEN DIAS : Providing and fixing Wooden Dias of size 600 x 600 x 1420 mm height in as per the detail specification given below. Top size (600 x 600 mm ) side (600 x 1420 mm), front side (600 x 1420 mm) made up in 19 mm thick Marine Plywood (IS 710 : 2010) of requisite manufacturer's viz. Green / Anchor / Centuary or equivalent approved make including necessary facias etc. with necessary lipping (BTC), mouldings as required including cutting, fixing, finished with 1 mm thick laminate of approved make ,type , colour and shade of glossy / Matt / Suede / Fine / Line / Wood grain finished lamination pattern with / without grooves as required to exposed surface and edges and the internal / hidden surface shall be finished with 0.80 mm thick laminate of approved make. Area other than laminated surfaces shall be finished with two coats of French polish of approved shade. Antitermite treatment to plywood and woodwork with ten years guarantee bond etc. including all leads lifts etc. complete as per the instructions of the Architect & Engineer-in-charge

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader/ Paver on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- Plant Mix Method and Grading - I Material

Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to IS 3395 : 1997 below concrete pavement including all materials and labour complete.

Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate ( natural sand/ VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, , cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in-charge , compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etc. complete. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete.

Providing and laying in-situ M40 Grade unreinforced plain cement concrete pavement with max 20% fly Ash ( Fly-ash upto 20% by weight of Cement) over a prepared sub base with 43 grade cement , coarse and fine aggregate ( natural sand/ VSI grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a Tilting type Concrete Mixer as per approved mix design, admixtures, spreading, laying compacting and finished in a continuous operation without paver machine, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providing cement vata in cement Mortar 1:8 @0.6m X 0.6m centre to centre, admeasuring 80 mm at bottom and 40 mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-in-charge. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete.

Providing and fixing in position TMT FE 500, 25mm dia dowel bars precoated with anticorrosive epoxy paint of required Dia. 60 cms. Long and at 30.00 cm. C/C and wherever directed including handling, straightening, necessary cutting supported by TMT FE 500, chairs with proper alignment by using properly designed assembly of Bulkheads lubricating half length with bituminous paint as directed etc. complete.

Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb without gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant

Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb with gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant

Stamp Concrete of 100mm Thickness - Providing and Laying in-situ M30 Grade unreinforced plain cement stamp concrete of 100mm thickness pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate (natural sand / VSI grade finely washed crushed sand) Confirming to IS 383, as per mixed in a batching and mixing plant / non tilting mixer and weigh batcher as per approved mix design, admixtures, transporting to site in nagpur city with lead upto 20KM (on Inner Ring Road from Avasti nagar to wadi), spreading, laying with approved make pover, compacted and finished in a continous operation, finishing to lines and grades Also Providing, Placing and applying stamp powder which is light fast UV resistant pigment with appropriate chemical compounds of desired colour on base concrete after excess bleed water has evaporated using dry shake method @5kg per sqm. Including texturing, and covering with plastic sheet (min 200 micron thickness) and also applying two coats of UV-stable,30 % solids clear sealer @ 150 to 250 gms per sqm using surface roller and protecting from falling dust,dirt and curring by curring compound / by providing cement vata in cement Mortor 1 :8 @ 0.6m x 0.6m center to center, admeasuring 80mm at bottom and 40mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-incharge or Landscape architect etc. complete. (prior approval of superinteding Engineer will be necessary )

Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete.

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.

Providing,aupplying,fabricating and fixing panel of aluminium composite panel cladding in approved shape made out of 4 mm thick ACP sheet material consisting of 3mm thick FR grade mineral core following NBC part IV Fire and life safety (having 2 hours fire resistance in accordance to ASTM E119-12 and BS476 part 6 and 7 class O) sandwitched between two aluminium sheets (each 0.5 mm thick of AA 5005/AA3105 grade) The aluminium composite panel cladding sheet shall be coil coated with kynar 500 based PVDF/Lumiflon based fluropolymer resin (having 70:30 ratio of PVDF and acrylic) coating of approved colour and sg=hade on top face and polymer (service) coating of bottom face as specified using stainless steel screws,nuts,bolts,washers,cleats,weather silicon sealent,backer rods etc .overall weight of the ACP shall not be less than 7.5 Kilogram/ One Square Metre)

Providing structural steel work in trusses, other similar trussed purlins and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2 coats of oil painting approved quality and shade etc. complete.

From 3.8 to 7.6m

From 7.6 to 11.4m

From 11.4m and above

Providing and erecting chain link fencing 1.6 M. height with G.I. chain link of size 50 x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x 25 x 5 mm size and vertical M.S. flat 35 x 5 mm and 25 x 5 mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete.

Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex.Engineer is necessary before use)

Providing detailed geological reports of proposed site by maintaining geotechnical investigation of structure stratification collecting soil, rock and ground water samples for laboratory tests to arrive the foundation design parameters . Rock properties such as type of rock, jointing fractures, etc. complete with suggestion about the site foundation and remedies.

Providing, fabricating and fixing M.S. grill work as per approved design and as per weight specified below to fencing / compound mades out of square / round bars, M.S. flats, angles, with necessary holdfast including painting with one coat of red oxide zinc chromate primer and two coats of approved synthetic enamel paint etc. complete as directed by Engineer In Charge.

Providing & Fixing in position, Acoustical Panelling made from Fabric wrapped Compressed polyester fibre nonwoven 9 mm panels on, 50 x 50 mm sal-wood frame of 600 x 600 c to c having wooden supports from wall of required length, in front of 1000 gsm synthetic wool 50 mm thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings / finishing-items / paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete

Providing & fixing in position Stage flooring Made from 18mm plywood 1200 x 2400 & 18mm Teakwood planks 100 x 800 having tongue & grove on Sal-wood frame of 50 x100 at 600mm c to c on stage surface including cost of required Cut-Outs, decorative mouldings / finishing-items / polish etc., as per Architectural & Acoustical Design & Instructions & Complete in all aspects. .including all materials labour,finishing etc complete

Providing & Fixing in position, Acoustical Ceiling made from Compressed polyester fibre nonwoven 9mm panels on approved heavy duty GI frame 300 mm c to c & intermediate channels at 1200 mm c to c, suspended with Hangers from Roof, including cost of required Cut-Outs, decorative mouldings / finishing-items & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour,finishing etc complete

Providing and fixing Mangalore tiled roofing with class ' AA' tiles including securing the last course of tiles near the eaves with steel flat 40 mm x 3 mm and 1.22 mm wire fixing 50 mm x 25 mm horizontal teak wood battens and iron works and oiling the battens etc. complete. (Excluding ridge and hip tiles).

Providing and fixing Mangalore tile ridge and hip tiles of class 'AA' including scaffolding if necessary, pointing with coloured cement mortar and curing etc. complete.

Providing and fixing frame work of anodised aluminium sections for suspended false ceiling consisting of aluminium T 50 mm x 40 mm weighing 0.39 Kilogram/m. at 60 cms c/c and fixed with ( 15 x 15 mm) flanges weighing 0.119 Kilogram/m suspended on 6 mm dia. mild steel rod weighing 0.22 Kilogram/m fixed on wall and beams including rounding of the edges with aluminium T of 50 mm x 40 mm weighing 0.39 Kilogram/m etc. including all labour etc. complete.

Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm With R.C.C. raft in B.C. soil area including cost of reinforcement, 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight 75 mm thick R.C.C. cover medium duty 100Kilogrametc. complete.

Providing and laying concrete pipes of I.S.NP. class of 150mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Free Standing Table @ 1200Lx600Dx750HT Providing and fixing Table of Size 1200 x 600 x 750 mm. Top: made from 25 mm Prelaminated Particle board. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine.Legs : C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel : Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :- Metal Powder Coated - Black Color, CPU TROLLEY :- Metal Powder Coated - Black Color, 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board,

Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.

Providing and laying in trenches 15 mm dia.heavy grade having embossed as ISI Mark galvanised iron pipes of 1.48 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying in trenches 25 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 3.01 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying in trenches 80 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 10.15 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying in trenches 100 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 14.74 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti- corrosive oil paint , 2 coats complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying concrete pipes of I.S.NP. class of 225mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and laying cement concrete pipe of IS 458:2003 NP-3 class of 1200mm diameter in proper line, level and slope etc. complete.

Providing and fixing screw down for 80 mm. dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Providing and fixing C.P. Angular stop clock with wall flange of approved make continental including necessary sockets/union nut etc. complete.

Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete.

Providing and fixing H.D.P container one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres

Providing and fixing reinforced cement concrete cover of size 60 cm x 45 cm with frame over inspection chamber etc. complete.Medium duty (100 Kilogram)

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with vibratory roller to the required density. By Mechanical Means -Grading I (Using Screening Type B (11.2 mm) Aggregate)

Providing and constructing 75 mm. thick Modified Penetration Macadam (MPM) road surface including all materials, preparing the existing road surface, spreading 40 mm. stone metal layers 30% crusher broken metal + 70% Hand broken (by breaking rubble obtained by blasting) heating and spraying the bitumen of specified grade @ 2 Kg/sqm, spreading 12 mm.size chips compacting with three wheel static roller having weight 8 to 10 MT. to achive the desired degree of compaction as per Technical Specification Clause 506 etc. complete. Including picking of existing WBM surface. (VG-30 bulk bitumen rates are considered to arrive at rates)

Providing and applying tack coat on the prepared surface heating by fames in Boiler and spraying bitumen set footed in bitumen boller on B.T. surface 2.5 kg/10 sqm.(VG-30 bulk bitumen rates are considered to arrive at rates)

DENSE BITUMINOUS MACADAM:--Providing and laying dense bituminous macadam using crushed aggregate of grading 1, premixed with bituminous binder Bitumen of specified grade,@ 4.50 % by weight of total mix and filler, transported at site with VTS, laid over a previously prepared surface , finished to the required grade ,level, alignment,and rolling to achieve the desired density for 76/100 mm compacted thickness with drum mix type hot mix plant with SCADA having complying essential features of Hot mix plant as per IRC-27-2009 specified conditions and attachments such as electronic load sensor based belt conveyers, automatic synchronization of bitumen and aggregate fedder,built in dust controller system and PLC for Drum Mix plant ,Sensor paver, and Vibratory roller excluding prime/Tack coat etc. complete --Bitumen VG-30 grade with stone dust filler (VG-30 bulk bitumen rates are considered to arrive at rates)

Providing & Laying mastic asphalt 25mm thick with 10/20 grade bitumen including producing the same at computerized batch mix plant transporting the same to site by means of mastic cooker, laying the same with mastic paver & including all necessary tools, labours & barricading, spreading of aggregate as antiskid measures by means over newly laid mastic asphalt as per prevailing MCGM specifications clause no.365 of Road works as directed by engineer in charge, (note : The material specifications / gradation and content shall be specified in the relevant IS codes)

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete.

Providing and fixing informatory sign boards in rectangular shape of size 1.20m x 0.90m made out of 16 guage Aluminum panel bonded with IRC Specified colour of retro reflective sheeting of Type IV High Intensity Micro-Prismatic Grade Sheeting (HIP) having pressure sensitive / heat activated adhesive, IRC Specified colour retro reflective cutout border & messages having pressure sensitive adhesive having border & messages in IRC Specified colour background including M. S. angle iron frame of size 35 mm X 35 mm X 3 mm & two M.S. angle iron post of size 65 mm X 65 mm X 6 mm, 3.65 m long, duly painted with flat oil paint having alternate black and white bands of 25 cm width including G.I. fixtures etc; fixing the boards in M-20 concrete block of size 60cm X 60cm X 75cm including transportation etc; complete. Aluminum Panel Type IV High Intensity.

Providing and fixing sign boards of size size 60 x 80 cm made out of 14 gauge M.S.Sheet with retro reflective sheeting of Engineering Grade as per M.O.T. specification No. 801-3(1993) white reflective back ground, lettering symbol bordering of black non reflective paint including 3.65 metre long M.S.angle one post of 65 x 65 x 6 mm size duly painted with white and black bands including fixing the boards of M.S. angle with galvanised nuts and bolts and washer. The Board shall be as per IRC-67-1977 including conveying fixing in ground with C.C. 1:4:8 block of size 0.60 x 0.60 x 0.75 m, with 7 year guarantee for the sheeting etc. complete. Mild Steel Board with Engineering Grade.

Providing and fixing in position factory made EPS cement sandwich wall/roof/floor light weight solid core pannel made of core material of EPS granule ball/beads (conforming to IS 4671:1984 and shall have density not less than 15 kg per cum) adhesive, cement,sand,flyash and other bonding material in mortar state processed to form in a preset mould. The outer face on both sides of the panels will be non asbestos fibre cement board confirming to IS 14862:2000 or Calcium Silicate Board confirming to EN 14306:2009 of 5 mm thick each Panels shall be laid on 6 mm thick cement mortar ( 1 cement : 2 fine sand)mixed with chemical adhesive of 0.5 Kg per 50 Kg of cement or shall be preferbly fixed into 'C' channel made of 1.2 mm thick MS plate screwed/fastenered to the salb/coloumn/beam etc. The Panel shall fixed vertically with tongue and groove joint and horizontally locked with steel bar between each other and floors and filled with cement mortar and adhesive. Panels should be used as floor and roofing with additional structure support, steel or RCC depending upon the design. All the operation shall be completed in all respect as per drawing, manufacturing specification and under the overall direction of Enginner-in-charge ( Cost of all the material is included except 'C' channel which will be paid separtely) C) Non Load bearing panels 90 mm thick required size

Providing and fixing of retro- reflectorised informatory sign board rectangular/Square in shape having area greater than 0.9 One Square Meterr made out of 4 mm aluminum composite panel bonded with 0.5 mm skin thickness on either side with white retro reflective sheeting of Class C ( Type XI Type XI Micro prismatic grade sheeting) having pressure sensitive adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3, supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with two coats of grey stove enamel paint and supported on two no. mild steel angle iron post 75 mm x 75 mm x 6 mm, 3.5 mt ~ 3.9 mt long firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing The angle iron post shall be duly painted with one coat of epoxy primer and two coats of epoxy finish paints having alternate black and white bands of 25 cm width including fixures and transportation etc.complete.The nut bolts of board with angle iron post/supporting structure after fixing at site has to be electrically welded. ClassC_ ( Type XI Type XI Micro prismatic grade sheeting) sheeting shall have 10 years written warranty from the manufacturer including the Digitally Printed areas with Latex printing technology with sheeting manufacturer approved inks and laminated with UV overlay film and this warranty certificate along with sheeting manufacturer attested 3 years outdoor weathering test report from Indian govt lab must be submitted to the Engineer in charge by the contractor/supplier.

Bamboowood 20mm thick Decking Outdoor Flooring Tile Providing & fixing in position Phenol bonded Epitome Bamboowood deck flooring tiles with planks of sizes 20mm thick, 1900 mm length and 135mm wide ,in approved colour , texture and finish , having performance Appraisal Certificate (PAC) issued by Building Materials& Technology promotion Council (BMTPC)with necessary profiled edges and groove fixed with 40mm ss screws 3 nos in each tile to frame work made of second class seasoned and treated teak wood of size 38x38 mm placed underneath acoss the tile at both ends and in centre fixed with clips holding in position. The Epitome Bamboowood planks shall have minimum density of 1000 Kilogram/cum & minimum hardness 1000 Kilogramf.all complete as per direction of engineer in-charge.

Supply and Installation of translucent roof with DPI Flux standing seam multicell polycarbonate panel system. The system with complete assembly of co extruded UV protected multicell panels incorporated into a complete system. Co-extruded UV protected polycarbonate panel system of min 12 mm thick of 900 mm (min.) width with angular daylighting concept. Panels shall have minimum six layers with truss bridge design for higher flexibility & strength. Panels with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels shall be manufactured with vertical standing seam at both sides of the panel. Panels shall be fixed on Purlin with snap on connectors with double tooth grip lock locking mechanism and will be secured on MS structure (will be paid Separately) with 3 One Numbers self-drilling screws & trapezoid SS fasteners holding the base of the standing seam offering best stability having a pull-out load of min. 7000N (7KN) tested as per ISO 6892:1998 and IS 1608: 2005, as per design requirement. Panels must satisfy Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate sheets which have been exposed to UV for a min. of 500 Hours as per ASTM G 155. Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. U value shall not be more than 1.6 W/m2K as per EN ISO 10077-2:2018. Panel shall be with additional End cap/Aluminium U/F profile/ Glazing Bar for ends as required. Panel shall be fixed over MS structural steel/MS purlin (paid separately) conforming to the detail technical specifications as per approved architectural drawings. Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing & direction of the engineering in charge. Colour: As per Approval. Approved Make: FLUX by DPI Daylighting or approved equivalent The 12mm thick panels shall be used for a roofing height of upto 15 mtrs.

Cutting transverse contraction joints 3 to 4 mm wide and depth 60mm. .in concrete slab using concrete cutting machine with diamond studded saw within 48 hours of casting of bay / slab etc. complete including subsequent widening of the groove 8 to 10 mm. wide at top having depth of 15 mm. as directed by Engineer incharge.

Providing to contraction joints polysuphide sealent (Pouring grade) confirming to BS : 5212 - 1989 into sawed groove widened at top for sealent reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam backer rod of required diameter (appraox. 25% larger than the initial 3 mOne Metric Tonneo 4 mm. joint) overlaid with bond breaking tape as per detailed drawing. Item includes cleaning the joints with water jet / air compressor and allowing joint to become thoroughly dry before sealent is applied and applying primer. (A) Contraction and longitudinal joints (15 mm. deep x 8 mm.wide)

Providing and laying wedge shear elemental layer (WSEL) by using rubble stone of size 15 to 20 cm thick in single layer of 230 mm including packing the same with 20 mm to 40 mm thick aggregates ( normal size) and using stone powder of 40 mm to 50 mm thick on surface and watering & compacting by vibratory roller confirming layer thickness of minimum 200 mm and as directed by Engineer - in - charge etc complete.

Providing Dozer D 80 A 12 (Medium ) for Dismantaling of various structure available on site.

Transporting of excavated/Dismantled materials lead upto 1K.M

Transporting of excavated/Dismantled materials lead upto 7 K.M

Providing and Supplying SAFETY RUBBER FLOORING SYSTEM Including Material, labours lead etc. complete after approval of Engineer in Charge

Providing and laying RED & BLACK GRANITE cobble stones of 100mm x 100mm x 100mm, 3 line dressing with 12 mm top layer in size of fine cut and well dressed in Grey colour in paving on a bed of min. 40 mm thick cushioning in C.M. 1:4 including neat cement float etc. filling of joints in C.M. 1:2 with grey cement to match the colour of cobble stone in the required pattern, design and as directed by the Engineer incharge, includingcleaning, curing etc. complete.

Accupressure Bed - Providing and laying in position P& F pebbles with colour flooring- of approved quality 25mm to 30mm thick in plain/diamond pattern on a bed of cement mortar 1:6 including cement float, flling joints with neat cement slurry, curing, polishing and cleaning etc. complete. As directed by Engineer-incharge

Providing and laying Natural unpolished Black/Brown Pebbles of size 30mm to 50mm

Providing and Supplying Sea sand Spec. No.: As directed by Engineer-In-Charge.

P/F 50-60 MM THK. MACHINE CUT BASALT STONE WITH UNDULATED FINISH AS PER APPROVED PATTERN AND SAMPLE MCGM e-tender no:- 7200039621

Providing and Fixing Processed Stone Cladding on wall surface/ plywood surface. RCC pardi/ Wall and all type of Interior, Exterior Compound wall and Gate etc. of cladding processed stone with material of Processed clay, Wooden chips, Silica sand, Cement, GFRC admixtures, Colour pigments, Fiber up to thick of 230 mm/ 25 mm including scaffolding, fixing of screw, etc. (As directed by Engineer in Charge)

Lift from 3.8m to 7.6m

Lift from 7.6m to 11.5m

Providing&fixing in position 20 +/-2mm thick machine cut, mirrorpolished, 1st quality granite cladding such as black galaxy or approved equivalent in lift lobby / passage installed in approved pattern and design of size 600 x 1200mm and as directed including backingcoat of 1:4 cement plaster of required thickness with stainless steelfasteners cleats etc. The joint between the granite slabs to be filled white cement mixed with with matching pigments. The rate toinclude all curing, polishing at all lift and levels. (Basic rate ofgranite is Rs.3600/-Sq.m.)

Stone work in plain ashlar in super structure upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : Both faced dressed with Red sand stone Cum

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and applying two coats of an approved wood preservative for anti-termite treatment to wooden surface as per manufacturer’s specifications and as directed by Engineer-In- Charge

Providing and laying in position Laterite stone of approved quality 15 cm thick, 380mm ht kerb stone on a bed of cement mortar 1:6 including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. As directed by Engineer-incharge

Providing and fixing finely dressed basalt stone of size 40 cm X 40 cm X 15 cm in washing place including cement mortar bedding of 25mm thk. In 1:3 proportion, cement float, levelling, smooth cement plastering along the sides to match the existing surface in cement mortar, curing, finishing etc. complete as directed by Engineer-In-Charge.

Providing and fixing Ductile iron Man Hole Covers/ Strom Water Grating and Grating with frame of Various sizes, weight and types and load bearing capacity as per EN-124, equivalent NECO with prior approval of concerned Superitending Engineer.

Providing and constructing Ductile Iron circular manhole 45 cm dia. At top 90 cm at bottom up to 1.80 meter to 2.70 meter depth including excavation, laying 1:4:8 cement concrete bedding 15 cm thick burnt brick mansonry with 1:1 cement mortar plaster 25 mm thick inside and outside 20 mm (1:3) ductile iron heavy type cover with ring 125Kilogramin weight. High strength. More life and Durability, Good Antiskid Grip, Suitable to heavy theatric loading, Light weight casting after cost benefits for Transportation Refilling etc. as per requirement. with prior approval of concerned Superitending Engineer.complete as directed by Engineer-in-charge

Providing and applying first coat of approved Waterproof primer, and two coats of waterproof acrylic based textured exterior paint of an approved make and colour as per manufacturers specifications to textured sand faced or other surfaces, upto 10m height from ground level and at all locations as directed including preparing surfaces for paintingby any approved means, scaffolding, cleaning and curing etc.

MULTI PURPOSE SCRAMBLER SET 1 , Product Area: 14.650 X 4.150 Mtr Safe Play Area: 17.650 X 7.150 Mtr

Providing and fixing Animal Mgr with all fitting as approved with Engineer-In-Charge

3 IN 1 (AERIAL STROLLER + SURF BOARD + SHOULDER TWIRL)

Providing and fixing Multi Seater See Saw with all fitting as approved with Engineer-In-Charge

Providing, hoisting and fixing at all level precast or reinforced cement concrete gazebo with all elements like roofing, string courses, bands, copings, columns, pillars beams, plinth beams, railings, benches, flooring, foundations including architectural design, moulding, arches, shapes, and applying proper texture and paining coats to suit a particular asthetic element (trunk of trees, shapes of animals, birds, timber benching, any element or structure representing culture or tradition) the cost of required centering, shuttering and reinforcement, of M25 grade and fibrous material, etc complete as per the instructions of Architect or Engineer-incharge.(Refer sketch 3)

Providing and applying one coat of approved silicate based primer with roller / brush and one coat of granite textured exterior paint of an approved make with spray to get designed finish with two coats of lacquer in approved finish shade of thickness 2-2.5mm as per approved manufacturers specifications to textured sand faced or other surfaces, at all heights and locations as directed including preparing surfaces for painting by any approved means, watering, scaffolding, cleaning and curing etc. complete as directed by Engineer-in-charge

Wall Painting art work : Designing, Conceptualization & painting of 3D artistic on any surface at all height and location as directed. The paint should be used for the artistic painting is high quality acrylic paint. painting should be coated with weather proof warnish.

Providing & fixing FRP/Granite/Stone Deluxe BENCH having length of 1.5m including all material, lead manpower etc. complete as directed by Engineer-in-charge.

Providing and fixing Garden Bench with Arm with all fitting as approved with Engineer-In-Charge

Ss Dust Bin Product area:0.76Sqm, Capacity in ltrs: 42.0 ltrs, Product height:0.92m

Carrying out low strain pile integrity test on 900 mm diameter pile including all arrangements for test, equipments/accessories, materials, labour, submission of test report etc but excluding the cost of installation of job pile (installation of pile shall be paid seperately as per releventitems)all complete as per specification and as directed by the engineer-in-charge

Conducting routine vertical load test for 1.5 times safe load carrying capacity by means of High Strain Dynamic Load Test including provision and erection of crane- hammer-drop mechanism, acceleration and displacement velocity transducers to record both force and velocity including excavation, dewatering, preparation of pile head including building up of pile, additional reinforcement if any etc. all complete as per approved method (ASTM D4945-89), submission of test report, specifications and instructions of the Engineer for piles of following diameter :750 mm

Conducting routine vertical load test for 1.5 times safe load carrying capacity by means of High Strain Dynamic Load Test including provision and erection of crane- hammer-drop mechanism, acceleration and displacement velocity transducers to record both force and velocity including excavation, dewatering, preparation of pile head including building up of pile, additional reinforcement if any etc. all complete as per approved method (ASTM D4945-89), submission of test report, specifications and instructions of the Engineer for piles of following diameter :900 mm

Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete

Providing and fixing Indian teak wood plank ceiling 20 mm thick plain underside tongued and grooved including iron screws, scaffolding, if necessary, including one primer coat on under side and one coat of coal tar on upper side etc. complete

Supplying Hot Rolled steel sheet piles having properties described in respective specifications or/ and shown in drawings (Z or U type with sectional modulus of minimum 2500 cm3, steel grade S430 GP with minimum yield strength of 430 MPa, minimum thickness 12.0 mm thickness, with Larssen interlocks and applying recommended sealant for complete watertightness (if required) & using suitable corner sections as per site condition) .Installing the same to line and level including making reformed steel sheet piles at required positions as corners, junction, wedges etc. as per approved drawing and specification in single or group jointing by welding properly, installing vertically along the alignment with the help of equipments like air compressors,excavator mounted / crane mounted vibro hammers / Impact Hammers / Hydraulic Pressing Hammers / vibrating drives powered by electric or hydraulic motor or combination of both based on the site requirements through the grooves to interlock together, wedges to make up for the permissible deviation of piles from the plumb lines caused during pile driving, slipped piles with the adjacent ones are found or loosened or dislocated during or after installation , sheet piles shall be pulled out and replaced with new ones

or redone including necessary modification to the sheet pile to suit the grove of existing sheet piles , including cost and conveyance of all materials, hire charges of equipments, hire charges of crane/rigs, cost of electrodes, mobilisation and demobilisation charges, all labour, other incidentals etc complete. ( No extra payment shall be made for cost of extraction and replacement for installing of sheet pile deviating the specification or rejected by Engineer -in-charge. The rate is inclusive of providing guide frames, cost of installation pit, formation and removal of earthen bund etc.). Payment shall be made on actual depth of sheet pile installation.(a) For depth 0 to 5 m below ground level(b) For depth 0 to 10 m below ground level

Supplying, fabricating and installing in position waling channel I.S 226 / 2062 quality to sheet piles to correct line and level as per approved drawing and specification with required accessories such as plates, bolt & nuts etc.for connecting with sheet piles as well as for splicing the channels, welding the channel joints to achieve the properties of the section / welding of connecting plates etc including cost and conveyance of all materials, cost of drilling holes, hire charges of equipments, hire charges of crane, cost of electrodes, cost of fixing with bolts, nuts & washers, all labour, painting one coat of zinchromite primer after rubbing and cleaning the surface with mechanical wire brushing, sand paper, other incidentals etc complete.(Rate quoted shall includes supplying, fabricating, drilling holes and fixing waling channels to SSP only ,cost of accessories such as connecting plates, bolts & nuts etc ).

Providing laying and fixing glass mosaic tiles in the wet areas like swiming pool, toilets etc. of approved make, colour, pattern, size and thickness on the surface treated with waterproffing compound including backing coat of approved latex-modified thinset, jointing, filling the joints with non shrink neat cementetious coloured grout, curing, ponding, finishing etc. complete as per manufacturers specifications and as directed by Engineer-in-charge.

Centering and shuttering including strutting, propping etc. and removal of form for Architectural Form finished concrete work using water proof ply 12mm thick conforming to IS:710. The water proof ply shall be used for only 2(two) repetitions after first use, and any repetition after the first usage shall be taken up only after prior approval for water proof ply material for suitability for use in form finish concrete (Architectural finishes) by the Engineer-in-Charge in walls (any thickness) including attached pilasters, butteresses, plinth and string courses, Suspended floors, roofs, landings, balconies and access platform, Shelves (Cast in situ), Columns, Pillars, Piers, Abutments, Posts and Struts, Stairs, (excluding landings)except spiral-staircases with water proof ply 12mm thick

Geological Survey to locate borewell by soil resistivity meter for ground water

Rig erection,setting,transportation of rig and other equipments

Supplying and installing jogging track (EPDM granules method) terracotta made of two layered water permeable all weather material of 2mm sprayed coat top with EPDM (Ethylene Propylene Diene Monomer) granules on 12mm in-situ polyurethane bonded rubber granulate sub-base layer of longer life and better UV resistance laid on IPS/PCC surface free from paint, wax, grease, oil, dust and dirt. The item includes cost of material, cleaning the IPS/PCC surface before installation and installation of the 2 layered track with proper slopes.Preparation of IPS/PCC will be paid seperately under relevant items.

Providing toilet of 4 units of 0.9*1.2M size of 1 unit with all necessary fittings such WC Wash basin overhead tank of 1000 ltr for each Type of WC : European with ceramic base , Water facility : By mean of overhead tank, Electric provision By mean of connection from main line, Bottom frame material: 35mm X 35mm X 5mm(thick) MS angle for one seater, Bottom frame support material : 25mm X 25mm X 3mm(thick) MS angle, Side & Top Roof panel frame material : 35mm X 35mm X 5mm(thick) MS angle, Top(roof) support frame structure : 25mm X 25mm X 3mm(thick) MS angle, Ventilation frame material: 25mm X 25mm X 3mm(thick) flat MS, Door frame material: 35 mm x 35 mm x 5 mm (thick) MS ANGLE, Support material for Door panel fixing: Aluminium U-channel of 18gauge, Door hinges(two numbers): 75mm size with 1.2-1.5mm thickness MS, Tank holder frame material: 25mm X 3mm(thick) MS flat, Unit understructure Supported by 4-legs of size 35mm X 35mm X 5mm MS angle with corner support of 25mm x 25mm X 3mm MS angle for 1-seater, Door Tee material: 40mm X 40mm x40mm X 5mm(thick) MS Tee,

Providing and applying required coats of a water based Evercrete Deep Penetrating Sealer (DPS) on cement concrete surface like roads, beams, and columns, plastered walls, basements, roofs, potable water tanks etc to react with cement and to penetrate concrete structure thereby making it resistant to chemicals / chlorides water to make it dust proof and to act as a water resistant at the same time which Strengthens the treated surface and reduce the curing period etc complete. - Note -- for item One Number 7 to 4 prior approval of Superintending Engineer will be necessary

Providing Steel Porta Cabin consist of With one Room of size 3050 mm x 2440 mm x 2590 mm ht having following specifications.1) PUF Wall Panel – Panel made up of micro ribbing Pre-Painted Galvanized Iron Sheet on both sides(have tongue groove arrangement) and 50mm thick composite PUF sandwich between Pre-Painted Galvanized Iron Sheet 2) Flush door 32 mm thick water proof.3)Window-Powder coated aluminium sliding windows with 4 mm tinted Glass4)Flooring- 15 mm heavy duty cement fiber board inside and outside texture paint.5)Roofing -The PUF insulated Ceiling panels. The covering on ceiling panels shall be micro riving Pre-coated galvanized iron sheet and Self draining Type Roof shall be provided with water proof covering 6) general electrical- Provision for 3 nos. tube light (18 Watt LED light) - 2 nos. wall mounted ceiling fan (300 mm) - 3 nos. plug and socket (3 pin 5 amps electric plug socket)- 1 no main input socket (32 Amp heavy duty 3 pin power socket with MCB)- split AC (1.5 T) provision

Providing Cabin of 3m*3m with below specificition and Approved with Engineer-IN-Charge etc complete.Specification:-.1)Walls :- 50 mm thk aerocon panel.2)Column :- Structural steel column of 100 x 100 x 6 mm thk.3) Paint:- Texture renova paint from outside and inside as directed by Engineer-in-charge.4)Roofing:- Monier tiles roofing with specified purlins and rafter and Ridge.5)Doors & Windows- Wooden with wooden/structural steel frame

Nameplate (3D acrylic hollow blocks with LED)S.I.T.C. of Nameplate stating in Devnagri/English font in the desired style as per specifications. The total assembly letters made of frosted acrylic sheets 5mm thick cut and glued together to achieve the hollow letters (side edges of letter made up of in Aluminium Composite Panel) as per approved design with provision for electrical supply for white/warm white LED lights of required wattage that will be lit from inside the blocks for illumination in the night. The whole assembly shall be rested/fixed with all necessary fittings and cleaning including supporting, M.S. Fabrication work etc. with required size C.C. foundation complete as directed by the Engineer-in-charge.

Heritage Look Plaster :- Provided heritage look plaster over provided plaster surface finishing with rustic textured material either in Basalt Stone Finished or Wooden finished of 10 to 12 mm thick including preparing the surface in various aspect like arche, scaffolding and curing etc complete as directed by Engineer-In-Charge

Providing and fixing FRP mural 1250 GSM with a minimum thickness of 6mm of any size and shape in all positions with proper metal reinforcement (With Epoxy Paint)with ISO mark. It should be realistic from all angles, have high strength and life, have a size of 3m x 1.5m and 3m x 2.1m or as per Approved by Engineer In Charge as required for each, and apply the Deco Paint brown Effect with 2 Coat PU with top coat of UV Iso-Gel Coating. The sculpture must withstand all weather conditions. Transportation to site and installation after taking approval and as directed by Engineer-In-Charge. (Including 5 Years of Maintenance complete.)

Providing and fixing replicas of various Forts in FRP 1250 GSM with a minimum thickness of 6mm of Approved size and shape in all positions, with height upto 1.5m for Raigad having Plan sizes of 20m x 9m and height 0.9m for all other forts design. Other Forts has various Plan sizes of 12m x 5m, 7m x 3m, and 3m x 1.8m with proper metal armature with ISO mark. It should be realistic from all angles, have high strength and life, and apply Deco Paint of appropriate color with with 2 Coat PU with top coat of UV Iso-Gel Coating. The sculpture must withstand all weather conditions. Transportation to site and installation as directed by Engineer-In-Charge. All design / Art work to be approved from Engineer-in-charge / PMC before starting of work. (Including 5 Years of Maintenance complete.)

Providing and supplying life-size sculptures of Mavla riding on a White elephant with height and width proportionate to each other. FRP of 1250 GSM with a minimum thickness of 6mm of Approved Actual Lifesize and shape in all positions (Size of Avg Indian Elephant -4m x 1.8m x 3m Height) with proper metal armature with ISO mark. It should be realistic from all angles, have high strength and life, and apply Deco Paint of appropriate color withwith 2 Coat PU with top coat of UV Iso-Gel Coating. The sculpture must withstand all weather conditions. Transportation to site and installation. All design / Art work to be approved from Engineer-in-charge / PMC before starting of work (Including 5 Years of Maintenance complete.)

Providing & Supplying of life size sculptures of Mavla riding on horse with height and width proportionat of each other. FRP of 1250 GSM with minimum thickness of 6mm of Approved Actual Life size and shape in all positions (Size of Avg Indian Horse - 2.5m x 1.25m x 1.5m Height) with proper metal armature with ISO mark.It should be realistic from all angles, high strength, high life and applying Deco Paint of appropriate colour with with 2 Coat PU with top coat of UV Iso-Gel Coating.The sculpture must withstand in all weather conditions.Transportation to site and installation. All design / Art work to be approved from Engineer-in-charge / PMC. (Including 5 Years of Maintenance complete.)

Providing & Supplying of life size sculpture of Mavals with height (Height of Each Mavla from 1.95m from Head to Toe) and width proportionat of each other .The model in FRP of 1250 GSM with minimum thickness of 6mm of Approved Actual Life size doing diifrent actions/position and shape with proper metal armature and weapon if any with ISO mark.It should be realistic from all angles, high strength, high life and applying Deco Paint of appropriate colour with with 2 Coat PU with top coat of UV Iso-Gel Coating.The sculpture must withstand in all weather conditions.Transportation to site and installation. All design / Art work to be approved from Engineer-in-charge / PMC. (Including 5 Years of Maintenance complete.)

Providing & Supplying of life size sculpture of Canons with length and width proportionate of each other FRP of 1250 GSM with minimum thickness of 6mm of approved shape in all position (Approx size 2.4m x 1.5m with 2.4m Barrel and 2 Wheel of 1.2m Diameter - Dia of Barrel 450mm from front shooting side and 600mm from end side) including various design of cannon from Maratha Empire with ISO mark.It should be realistic from all angles, high strength, high life and applying Deco Paint of appropriate colour with with 2 Coat PU with top coat of UV Iso-Gel Coating.The sculpture must withstand in all weather conditions. Transportation to site and installation. All design / Art work to be approved from Engineer-in-charge / PMC. (Including 5 Years of Maintenance complete.)

Providing and Installing water fountain of 3 M dia with below sepcification wall should be of brick wall of0.45 m width and 0.9 m ht above ground and cladded with granite tiles. Inner area with wall and flooring should be waterproffed inner area wall and flooring should be done with premimum glass mosaic tiles. Electricals wire of 4 core 16 sqmm and submisserble pump of 7 HP with all necessary fitting and control panel (Including Glow lighting ) Main sculpture as shown in dwg in GRC and other small sculpture of any animal in GRC.Plumbing work with all necessary fittings of pipe and nozzle etc complete as directed by Engineer-In-Charge (With 5 Years of Maintenance)

For Lighting Water Fountain :SITC of Nozzles Geyser Jet 25mm (MOC-SS304/Brass ) (Effect Height 1 Mtr) Geyser Jet 40mm (MOC-SS304/Brass ) (Effect Height 2 Mtr) ,SITC of Filter400mm dia Top mounted filter with clamp mounted 1.5" MPV 6.50m³/hr. 0.13m², 50kg sand & 25kg GravelSITC of PumpsPump 0.5HP Submersible, 1 phasePump 5HP Submersible, 3 phaseSuction Strainer for above pumpsSITC of Dosing Unit4 Kg, Chemical Feeder (Chlorine/ Bromine Dosing Unit (IN-LINE Feeder)SITC of LightsSubmersible LED Color Warm White Light 18W (6x3W LED's) IP68 Light Stands made of SS 304 as per site requirementsDeck Box (Suitable for Use with Lights) IP65SITC of Pool Basin fittingsSuction Point (ABS)Connector with Puddle Flange (Wall conduit for 2” threaded fitting)-ABS/PPFloor Inlet Nozzle (ABS) AdjustableSITC of UV SterilizerBlue Lagoon UVC Tech 16000L/16Watt, 5m³/hrSITC of Pool Cleaning KitVacuum Hose 50 Ft. Leaf SkimmerBrush 18"/45cm. (Polybristle Wall Brush) Vacuum Head Telescopic pole (2.5 mtr - 5Mtr. Long) SITC of Control PanelControl Panel (Panel body custom made indoor type Made of 16 guage CRC/MS sheet epoxy powder coated with Amp meter, voltmeter, MCB, push button, isolator, indicator etc. panel incommer with MCB, neutral link etc and starter for pumps with Contactors, Overload Relays, Single Phase Preventers, internal wiring including power supply for the lights (Panel should be complete in all respect) Panel Equipments Make-L & T, Heger, Elmex,Rishabh,FTC, Esbee, Salzer,Schneider,Dowels, Jainsons, KSS,SG,Siemens etc.)SITC of Pipes in uPVC 10kg pressure and fittings (Heavy)SITC of Valves, fittings etc of required sizeSITC of Wires/cables of various sizes including required accessoriesSITC of Conduits, bends, fittings etc. of required size

Providing and supplying Wooden Teakwood Maratha Armour War Ship (Source material should be checked ,verified and certificate will be submitted to the Engineer in charge) aprox size of Ship will be 6mt x 2mt x 6mt ht. including creative involvement of artist as per Prior approved design and theme as instructed by Engineer-In-Charge/architect. It should be realistic from all angles , have high strength, and high life, and while constructing the Maratha Empire's Navy Ship considering all details and parameters and apply Deco Paint of appropriate color with PU Coating. The sculpture must withstand in all weather conditions.All design / Art work to be approved from Engineer-in-charge / PMC. Transportation to site and installation. (Including 5 Years of Maintenance complete.)

Providing and supplying Approved Metal sculpture (Material should be in Cast Iron) of various art pieces i.e. Shield, helmets, muskets,wagh nakh, matchlocks, firangi swords, clubs, bows, spears, daggers, etc, including creative involvement of creative artists depicting Armours and Weapons especially in the Maratha Empire as instructed by Engineer-In-Charge/architect.The model to be done in the following stages clay work,pop moulding 4 to 5mm metal casting with steel reinforcement from inside. Griding finishing and colouring (with Anti-corrosive agent in it) with appropriate colours .Transportation to site and installation. All design / Art work to be approved from Engineer-in-charge / PMC (Including 5 Years of Maintenance complete.)

Providing and Fixing Stone Work of Triangular carved Khandki stone of 0.45 x 0.3 x0.10 m thick over the masonry wall in 1:1 cement mortar including transportation loading unloading and all labour, artistic work complete to the entire specification of the architect and engineer-in-charge include etc. complete The sample of the design should be made and approved by the Permission and Approval of Engineer-in-Charge and PMC

Providing and Fixing Khandki stone for flooring and step 150mm thick of size 0.23x0.30x0.125 to 0.15 mts and not less than 0.2x0.25x0.125 Mtrs, cut in shape and two adjacent sides to be dressed and fixed in 1:1 cement mortar over a provided bedding of 150 mm .thick Cement Concrete in 1:2:4 of trap / granite / quarzite / gneiss metal including striking joints, watering, transportation loading unloading and all labour , artistic work complete as per the instruction given by engineer in-charge

Providing cast iron and mid steel work for gate with all bracing,gusset plates etc.as per detailed designs and drawings or as directed including cutting, frabricating, hosting, erecting fixing in position,making riveted/bolted/ welded connection and one coat of anticorrosive paint and over it 2 coat of oil painting complete

Providing and fixing curve, arched basalt stone door lintel in wall of given size. The stone of size given by architect cut in shape and two adjacent side to dressed fixed in 1:1 cement mortar in superstructure including carving dressing, scaffolding and watering including transportation loading unloading and all labour , artistic work complete to the entire specification of the architect and engineer-in-charge include etc. complete

Providing and fixing double leaf heritage type grand opening door ( maha Darwaja) with a small entry door on one of the door leaf of given size made up of superior quality teakwood Battens 300 to 400 mm wide and 35 mm thick. these battens are connected by horizontal and vertical planks, (ledges or Rail) on both sides of size 100 to 200 mm wide and 30 mm thick and metal patti with brass fittings, hinges, Patti and decorative flower on elevated wooden members as shown in drawing. This also including fixing brass screws, lock, cutting, sawing, making groove, making rounding on edges if required, making proper wood jonery, scaffolding if necessary all iron work and applying melamine polish including transportation loading unloading and all labour , artistic work or as directed by Engineer-In-charge etc complete (With 5 Years of Maintenance) The source of teakwood verified and approved by Engineer In-charge1) Main door 3.2 X 5mt ht and small door 1.2 X 2.1 mt

Providing and fixing Deepstambha of 3 m x 3m x 6 m size having 3m x 3m x 0.45 to 0.6 m plinth carved the edges and cornish like heritage look. Stambha of octagonal shape 0.8 to 0.9 m side at base and tapering towards top holding an inverted lotus or kalasha form, height of 5.4 m stambha made in basalt stone having 220 to 245 carved armed deeps in it including transportation loading unloading and all labour , artistic work, provision of electrical wires, conduits and all necessary equipment’s and fittings like lights etc as directed by engineer in charge and shown in figure. The sample of the design should be made and approved by the PMC architect and engineer in-charge(Including 5 Years of Maintenance complete.)

Design Supply and Installation of the Mangroves Trail Walk as per the DesApproved Design & Drawing Details and Specification of Project Information Memorandum (PIM) attached. Technical Specification :• The mangrove trail should be made in a sustainable method. To avoid harm to the environment/ ecosystem.• The all components should be made in wood/ substitute to wood, but the metal too avoids rusting of the members.• Piles are proposed to be in Jambha (Botincial Name: Xylia xylocarpa) wood which should be designed to take the axial load upto 2000 Kg Per pile. These Piles should be drilled in the mud/ marshy land at 2 Meter c/c and then should be made ready to receive the primary beams on them.• Primary beams should be made in first class teak wood/similar quality substitute. The primary beams do run along the trail, and do support the trail deck which should be designed for live load of 500 kg/sqm.• Secondary beams are then rested on primary beam perpendicular to the primary beam are to be made of the Nature fibre Composite Material/ similar quality substitute. These secondary beams support keels in made from secondary Nature fibre Composite Material which then support floor finish.• Floor finish should be made to take wear & tear of the people movement, giving appropriate friction in all the seasons and should be long lasting with minimal maintenance. These floor boards can be made in Nature fibre Composite Material). Designing load of 500 kg/sqm should be considered.• Handrails and brackets supporting them should be made in Nature fibre Composite Material / similar quality substitute.• All of these components should be strictly fixed with nut bolt system made up from high grade stainless steel nut bolts only.

Providing and fixing sheet glass of 24 oz. for all size including putty etc. complete

Providing & Arrangemnt of High Back, Synchronized Mechanism with Multiple Locking, Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Leatherite Upholstery

Providing & Fixing in position, Carpet more than 800+ gsm, made with100% stain proof fibres of approved make along with 5mm underlay as per Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour,finishing etc complete

Providing & Fixing in position, 1000 mm wide Auto-glow Aluminium extruded strips on auditorium steps as per Design & Instructions & Complete in all aspects. Make Piccolo or Nexus

Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) (As directed by Engineer in Charge)

Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete.

Providing and laying ceramic tiles having size 30 cm. x 60 cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.

Providing 25 mm to 30 mm thick partition of polished black kadappa stone slab of approved quality including giving required size and shape etc. Fixing in cement mortar 1:3 curing and cement etc. complete. b) Both side polish

Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.

Providing and Fixing 30 MM thick BOTH SIDE PRELAMINATED SOLID PANEL PVC DOOR SHUTTER consisting of frame made out of M.S tubes of 19 guage thickness and, size 19 x 19 mm for styles and 15 x15 mm for the top and bottom rails, M.S frame shall have a coat of metel primer of approved make and manufacture. M.S frame shall be covered with heat mouled PVC 'C' channel made from 5 mm (+/0.25) thick prelaminated sheet of density 600 Kilogram/cbm ,of size 30mm thickness 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45? angle on either side forming stiles ; and 5 mm thick ,95 mm wide PVC sheet out of which 75 mm shall be falt and 20 mm shall be tapered in 45 on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be falt and 20 mm shall be tapered on both sides to form lock rail.Top,bottom and lock rail shall be provided either side of the panel. An additional 5 mm (+/0.25) thick PVC strip of 20 mm width is to be stuck on the bottom side of the ' c ' channel prelaminated paneling of 5 mm (+/0.25) thick PVC sheet to be fitted inside the M.S. frame welded/ sealed to the styles and rails with 5 mm (+/0.25) x 30 mm PVC sheet beading on either side and joined together with solvent cement adhesive etc ,10 mm thickness (5 mm (+/0.25) x 2 nos ) 20 mm wide cross PVC sheet as gap insert for the rail and bottom rail. Door to be fixed to frames with 3 nos M.S.powder coated but hinges of size 100 mm x 25MM x 2mm using 32 mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardwares

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete.

Providing and fixing white glazed urinal with Pressmatic auto closing valve having flow rate up to 4.0 Litr/Minute of Jaquar/Cera/Hindware /Perryware or equivalent make with P.V.C. waste pipe with fitting arrangement etc.complete as directed by Engineer in charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)

Providing and fixing white glazed earthenware Wash Hand Basin of 55cm. x 40 cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connections including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete.

Providing soak pit of size 120cm x 120cm x 120cm including excavating and filling with brick-bats.

Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete.

Providing, laying and fixing P.V.C. pipe of 15mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing, laying and fixing P.V.C. pipe of 20mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing, laying and fixing P.V.C. pipe of 25mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing, laying and fixing P.V.C. pipe of 32mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing, laying and fixing P.V.C. pipe of 40mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete

Providing and fixing in position UPVC ultra violet stabilized 110 mm outer diameter cowl dome confirming to I.S.-4985 including making joints with solvent cement etc. complete

Providing , constructing and fixing 600 mm dia. Inspection chamber made up of Polypropylene / polyethylene material Having 315 mm diameter inlet(s)/outlets and with eccentric reducers as per requirement to connect 160 mm and 200 mm pipes having thickness of 5 mm and 600 mm in height, with inbuilt shaft achieve the invert depth as per site condition of wall thickness of 5 mm having R.C.C. cover and frame fixing in 150 mm thick in c.c.1:2:4, having crushed sand bed of 150 mm thick of size 750 mm dia. Including excavation and refilling the sides of chamber by ?sand crushed cushioning 150 mm thickness, connecting all required UPVC fittings with rubber lubricant etc.complete.

Providing and fixing C.P. 2 Way BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.

Providing and fixing 8 cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete.

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Providing and fixing 20mm diameter water meter with non-return valve including strainer, sockets/ union nut including water meter box making locking arrangement and lock. (without chamber).

Providing and fixing 40 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete.

Providing and fixing 90 cm x 60 cm Granite plate engraving 10 cm. Height letter, figures including painting the lefters/figures with approved colour and shade complete

Providing & Fixing in position Acoustical Doors along with 150 x 150 mm teak wood frame, doors made from 50mm Teak wood frame 600 x600 c to c filled with 1000 Gsm synthetic wool 50mm thick and 3mm Tecsound from both sides, 12mm waterproof ply & veneer from both sides , including 150mm heavy duty SS hinges (Geze / Dorma or eq.) 4 no each leaf, with Door-closer (Dorma / Geze or eq.) including cost of required Cut-Outs, decorative mouldings / finishing-items / melamine polish & Scaffolding as per Architectural & Acoustical Design & Instructions & Complete in all aspects .including all materials labour,finishing etc complete

Providing and fixing white european type wall-hung, Size 360mm x 360mm x 575 mm with flush valve having flow rate up to 6.0 Litr/Minute of Jaquar/Cera/Hindware /Perryware or equivalent make including PVC soil pipe, vent pipe upto outside face of wall, 100mm dia PVC plug bend inlet pipe all fittings,cutting & making good walls, floors etc as directed by Engineer in charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)

Fabrication, Supply & Installation of MS Portable Cabin on site as per the design drawing provided by the engineer of minimum height 11’ and made of following material Top Frame of 50mm X 50mm Specially Formed M.S Square Pipe, bottom frame of 125 mm X 75mm Specially formed M.S. I Beam , 5mm Thick Horizontal Cross Member :- 100mm X 50mm Specially formed M.S. I Beam, 5mm Thick Vertical Cross Member :- 50mm X 50mm Specially Formed M.S Square Pipe Bottom Frame should be painted with Black Japan kind of material. Using 20mm X 40mm Specially Formed M.S Square Pipe as a stiffener for top, for side wall stiffener having 20 mm X 40mm Specially Formed M.S Square Pipe, and side post having 65mm X 65mm Specially Formed M.S Square Pipe. Outside panelling should be done in Specially Corrugated Sheet in Ms. – 1 mm thick (18 guage). For internal wall panelling 8 mm PRELAMINATED BOARD SHEET. SHADE- HIGHLAND PINE with Bidding Patti and L-Patti in Black Coated Aluminium material should be used. (Internal partitions, toilet/bathrooms toilet fittings and accessories to be paid separately) the rate is inclusive of transportation charges, electricity/diesel generator charges.) Detailed specification & drawing are available with the office of Dy.Ch.E.(HIC).

Providing and Fixing toilet set for differently Abled persons consist of Floor Mounted white vitreous china water Closet including 6 litre capacity white vitreous china flushing Cistern with raised soft-push button, white vitreous china wash basin of size 46 x 36 cm and one no SS 304 hinged rail 76 cms & three no SS 304of (Grab Bar) 60 cms all including cutting and making good the walls and floors wherever required ,seat cover, cistern & wash basin fittings,nuts, bolts and gasket etc complete as per the direction of Engineer-In-charge.

Providing & constructing Soft board panelling with soft board &fabric.

Providing and fixing mild steel grill railing 20 Kilogram/sq.m with teak wood hand rail of size 75mm x 60 mm.and sill of 75mm.x 25 mm.and newel posts for staircases, including fabricating, fix-tures, erecting, painting the grill work with one coat of anti-corrosive paint and two coats of oil painting with approved colour and polishing the sill, hand rail and the newel post with french polish.

Laboratory Charges Standard Consistancy, Fineness, Specific Gravity, Setting Time ( Initial & Final ), Compressive Strength, Soundness.

Water Absorption, Specific Gravity,Impact Value, Crushing Value.

Sieve Analysis.

Abrasion Value.

Flakiness Index & Elongation Index.

Stripping Value. (for Bituminous Work)

Soundness.

GSB Mix Design./Cement Treated Sub Base ( CTSB)

Fineness Modulus ( Sieve Analysis ),Silt & Clay Content

Chloride & Sulphate Content.

Silt Factor.

Flexural test ( Set of 6 Tiles), Water Absorption ( Set of 6 Tiles).Resistance to wear ( Set of 6 Tiles).

Flooring of Natural Stone (Kota,Marble, Granite,Tandur.etc.) Water absorption, Specific gravity

Compressive Strength OF C.C. Cube (Set of 3 cubes).

Concrete Mix Design (With all Tests on basic materials)

Compressive Strength , Water Absorption,(Set of 8 Blocks)

Crushing Value/Compressive Strength, Water Absorption & Specific Gravity,

Sieve Analysis.

Liquid limit & plastic Limit.

Compaction Test ( Proctor Density ).

Sulphate & Chloride Contents.

Density Test . (Set of 3 Blocks ),Compressive Strength. (Set of 3 Blocks ),Water Absorption Test ( Set of 3 Blocks )

PH Value, Sulphate & Chloride Content.

Weight per running meter,Diameter of pipe & wall thickness of pipe,

Weight per running meter,Diameter of pipe & wall thickness of pipe

Upto 16 mm (Set of 3 Bars)Tensile strength, %, Elongation, Yield Stress,Weight-Per Meter, Bend / Rebend Test, Proof Stress.)

Above 16 mm (Set of 3 Bars)(Tensile strength, %, Elongation, Yield Stress,Weight-Per Meter, Bend / Rebend Test, Proof Stress.)

Reflectance & yellowness index.

Retro Reflective Test.

2. GARDEN / LANDSCAPE / HOTRICULTURE Preparing instant Lawn:- Excavating the ground to a required depth of 20cms, removing & conveying unwanted stuff to a required distance as directed. providing and Filling fresh garden soil/silt & manure in excavated area in 3:1 proportion to a height of 20cms.Mixing garden soil and manure thoroughly well, levelling, watering on previous night. Planting required variety of lawn grass as (fix lawn turf in slabs/ rolls of) directe and maintaining till 30 days by watering, weeding, clipping, rolling etc. complete.

Preparing Lawn (30 Cm depth):- Excavating the ground to a required depth of 30cms, removing & conveying unwanted stuff to a required distance as directed. providing and Filling fresh garden soil/silt & manure in excavated area in 3:1 proportion to a height of 30cms.Mixing garden soil and manure thoroughly well, levelling, watering on previous night. Planting required variety of lawn grass (Cynadon/ paspalum) as directed and maintaining till 30 days by watering, weeding, clipping, rolling etc. complete.

Preparing Shrubbery:- Excavating the ground to required depth of 30cms, removing and conveying unwanted stuff to a required distance as directed. providing and Filling fresh garden soil & manure in excavated area in 3:1 proportion to a height of 30cms. Mixing garden soil and manure thoroughly well, levelling, watering, on previous night. Planting well-rooted shrubs 0.5 Mtrs.apart as directed and maintaining till 30 days by watering, weeding, clipping, rolling etc. complete.(Mogara/Jasminum, Murraya / Kamini,Nerium, Ratrani/Night queen, Asparagus , Duranta Golden)

Hibiscus , Ixora mini , Tagar mini , Pentas

Gardenia Anant , Ixora singaporensis , Spathiphyllum

Cordyline

Ixora Duffy pink , Ixorachinensis ,

Plumbago

Ficus Safari , Ficus Starlight

Plumeria Dwarf singapore pink

Planting large flowering/Shady trees:- (Minimum Height to 1-2 Mtr. )Digging pit with size 0.6 m × 0.6 m × 0.6 m Removing & conveying unwanted stuff to a required distance as directed. providing and Filling the pit with approved excavated material up to a hight of 0.30 m. and remaining height of 0.60 m. with fresh garden soil & manure in in 3:1 proportion. Mixing soil and manure thoroughly well, leveling, as directed, watering previous night. Planting two or three year old,minimum 2.0 mtr. mtr. hight, healthy tree sapling as per specifications Maintaining till 30 days by watering, weeding, clipping, rolling etc. complete.KaduNeem

(Bahava , Bakul , Kadamb,Tabebuia, sita Ashok)

Palas

Coconut ( 4 to 5 Ft)

Plumeria Alba (Average Height = 120 to 180 cm)

Royal Palm (7 to 8 Ft)

Plumeria Rubra (Average Height = 120 to 180 cm)

Fox tail Palm (7 to 10 Ft)

Providing Well Developed , Healthy Fresh Free from Pest and Diseses Heavenly blue/Morning glory (Thunbergia grandiflora) (25 Nos/ Sqm)

3. Electrical Work Providing ISI mark G.I. pipe of following class and dia. excluding GST levied by GOI & GOM in all respect, inspection charges, transportation to stores, etc. complete as per IS-1239/2004.Note : One coupler shall be provided with each full length of pipe cost of which is included in rates below

Supplying and erecting minimum Three & above star rated submersible pump set of 2.25 KW/3 HP with 415 V, 50 c/s AC supply suitable for 150 mm dia. borewell suitable for 100 to 450 LPM discharge at 53 to 5 m head & discharge & delivery Pipe Size-50mm diameter with a necessary H type clamps as per specification No. WP-SMP

Supplying & erecting flat flexible 3 core 2.5 sq.mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete

Supplying and erecting metal work in CRCA sheet including Iron work for supports with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete

Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting ultra violet storage type water purifier (RO+UV+UF) with softener for safe drinking water consisting of UV germicidal tube of 8W capacity choke made of copper wire and two indicator lamps with output of purified water minimum 0.33 litre/min with activated carbon filter and softener operating on 230V, single phase A.C. supply with UV fail & filter change indication system .(for TDS more than 200)

Supplying, erecting, testing and commissioning self contained water cooler 230/250V 50Hz nominal cooling capacity of 80 litres per hour and storage capacity 120 litres with partially stainless steel body as per specification no. AP-WCR/WC

Supplying, installing, testing & commissioning 3 phase, 11/0.433 kV, 50 Hz., 315 kVA, mineral oil immersed and naturally cooled outdoor type, Copper wound, without gas cushioning, hermetically Sealed transformer, delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 45℃ by thermometer in oil and 50℃ by the resistance method in winding at full load rating, using type A winding insulation (kraft paper) with HV tapping (with off load tap changer) off load +5 to -10 in steps of 2.5%,having 7 number of tap positions, with standard accessories complete with test certificate with losses below 1025 Watts at 50% load, 3100 Watts at 100% load as per IS:1180 (part 1) : 2014 : 2021 with necessary permissions of Electrical Inspector, as per specification no SS- TR-HSL

Provoding M-30 CC Foundation for Transformer and Metering Cubical Including all labour, material, handling, and transportation costs included and as directed by Engineer In Charge

Supplying and erecting mini feeder pillar with 415V, 315-320A FPMCCB as incomer and 3 outgoing circuits with HRC fuse base and cartridge of 100A aluminium bus bar erected in 14 SWG CRCA sheet box with supporting angles, self locks, gasket and enclosure must be dust proof, rust proof, vermin and water resistant, having slanting top and erected on angle iron/ GI frame in provided C.C. foundation complete as per specification no. SW-MFP.

SITC Of street light control panel inclusive of all electrical accessories mentioned in tender documents

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking FPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting and marking triple pole isolators only switch version of miniature circuit breaker of 40A with required wiring connections and lugs etc. in provided distribution board.

Supplying, erecting and marking four pole isolators only switch version of miniature circuit breakers of 63A in provided distribution board.

Supplying, fixing and commissioning MCB type change over switch 2 pole, 40 A with 3 positions (I-O-II) with centre off position as per specification no. SWSWR/ MCBCOS

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 12 ways /phase (36 poles), with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Providing & erecting 3 Pole MCCB 415V, 250A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Supplying, erecting & commissioning 4 pole RCCB 63A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/ trunking/ inside pole/Bus bars or any other places.as per specification No: WG-MA/BW

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete

Supplying and erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/A

Supplying and erecting shockproof 3 pin plug socket 6A with porcelain base / flush type erected on filled polypropylene board or polished thick varnished double wooden block / folded or screwed board with top of either wooden / 3 mm thick hylam sheet/ 4mm thick plywood pasted with 1.5 mm thick laminate with S M screws and duly connected

Supplying and erecting shockproof 3 pin plug socket 16A with porcelain base/ flush type erected on filled polypropylene (IS:14772-2000) board or polished thick varnished double wooden block / folded or screwed board with top of either wooden/3 mm thick hylam sheet/ 4mm thick plywood pasted with 1.5 mm thick laminate with S M screws and duly connected.

Supplying and erecting modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting HMS PVC conduit FRLS grade 20 mm dia. With PVC accessories on wall / ceiling as per specification No: WG-MA/CON.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 16 / 18 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Point wiring in for light/fan/bell in 20 mm metal conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, flush type switch, earthing and required accessories as per specification No: WG-PW/SW

Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm, Max. Energy Consumption of 28W having service ratio (CMM/W) of Min. 8 , PF>0.9, THD<10% with IR remote control, Temperature Rise of Max. 40 deg.C, having external mounted control PCB completely erected in position as per specification no. FG-FN/CF

Supplying and erecting condenser 2.5 micro farad for ceiling fan.

Supplying and erecting electronic type step regulator for ceiling fan 600/ 900/

Supplying and erecting fan hook box of 10 mm M.S. round bar bounded to the R.C.C. bars upto 50 mm length each side and pierced through a 16 S.W.G. thick aluminium/M.S. Bowl 100 mm dia.or equivalent square size and having depth upto 75 mm complete erected with duly painted by one coat of red oxide paint and two coats of paint erected in position and without any leakage of slurry of cement concrete on either side of the box and positioned to the bottom level of the slab.

Supplying and erecting 20mm dia. corrugated flexible polypropylene conduit

Supplying and erecting exhaust fan heavy duty 230 V A.C. 50 cycles 375/380 mm. 1400 RPM complete erected in position as per specification no. FGFN/ EXF

Supplying & erecting ready to use Retrofit T8 LED 18 / 20 tube light with polycarbonate body, heat sink, integrated HF electronic driver complete & compatible to T8 / T12 LED luminaire by disconnecting starter & ballast if necessary.

Supplying & erecting 10-12W, 230V integral type LED Lamp suitable for B- 22/E-27 base as per specification no. FG-LP.

Supply, Installation, Testing and commissioning of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete. Specification no. EA-MOBI

Making trench in soft soil having 0.75 m depth and minimum 0.3 m width for laying provided cables up to voltage level of 1.1kV complete As per specification No. CW-EXN-CTR

Supplying & erecting integral post top lantern fixtures (mushroom type) suitable for LED lamp upto 12 W consisting of clear acrylic top cover, cast aluminium pole cap complete with accessories on provided pole /bracket as per specification no. FG-ODF/PTL.

Supplying & erecting integral post top lantern fixtures (light house type) suitable upto LED 18 W Lamp consisting of combination of spun aluminium canopy & clear acrylic top cover, cast aluminium pole cap on provided pole/bracket as per specification no. FG-ODF/PTL

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation, fixing provided nut bolts with the help of template, duly plastered as per design complete (for 3 to 5m octagonal / conical GI pole).

Supplying & Erecting Decorative light pole of height 4 m high (clear height) with decorative Single bracket made out MS Pipe as per lS1161:1998.The Pole will have provision for in bUilt junction box weatherproof flush door & locking arrangement for housing at bottom Of the dia of the pole shall be 140 mm & top section dia of 76 mm and base plete dimensions 250x2S0x10 mm thick and bottom and middle pipe of the pole shall be provided with cast iron /AlUminium embellishment to add aesthetic on the pole with the help of grub screw.The body of the decorative pole and bracket will be duly painted in U.V ray-resistant PU coating in an approved colour shade. The coating Should have a DFT Of 50 microns.The final design shall be got approved from Engineer in charge.

Supplying and erecting integrated LED flood light fitting Max. 30W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min. 3000 Lumens, min. efficacy of 100 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver with U shaped bracket with 3 Years warranty as per specification No FG-ODF/FLS2.

Providing , Supplying and erecting Luminaire LED flood light fitting 120W Including all labour, material, handling, and transportation costs included and as directed by Engineer In Charge

Supplying and erecting LED square / circular Max. 11 W down lighter/Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1200 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED square / circular Max. 25 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2750 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting integrated LED Bollard Cylindrical /Cubical shaped 800mm 8W IP65 & IK10 class having extrusion aluminium housing with polycarbonate diffuser, having system lumens output of Min. 800 Lumens, min.efficacy of 100 lumen/W, CRI>80, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-240V, inbuilt surge protection of 2 kV, Life class of 25,000 Hrs. at L50B50, including driver complete with 2 Year warranty as per specification No FG-ODF/FLS2.

Supplying and erecting integrated LED round burial light 6W IP65 & IK10 class having pressure die-cast housing, having system lumens output of Min. 500 Lumens, min. efficacy of 85 lumen/W, CRI>80, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 100-240V, i nbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L50B50, including driver, salt spray tested for 500 Hrs. including making of recess of appropriate size for flushing into surface with 2 Year warranty as per specification No FG-ODF/FLS2.

Supplying and erecting Concealed type foot/step light Max. 5W having IP67. IK10 rated Pressure die cast housing having system lumens output of Min. 500 Lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, SDCM<5, p.f. >0.95, operating range of 230-270V,surge protection of 2.5 kV, Life class of 25,000 Hrs. at L70B50, including driver by making necessary arrangement/recess in wall to make it flush with surface with 2 Year warranty.

Providing and Fitting of 15W LED track light of three light in each track of 3 m length Including all labour, material, handling, and transportation costs included and as directed by engineer-In-Charge

Supplying & erecting FRP box of size 150mm x 125mm x 100 mm, 2.7 mm thick complete on pole/wall as per specification No. CB-SB

Supplying & erecting crimping type copper lugs for cable upto 16 sq mm complete as per specification No. CB-CL/CU

Providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP

Supplying and erecting bus bar chamber triple pole with neutral with four aluminium bars, 500V, 100A having 15mm (Width) X 3 mm (Thickness), with 99.9 % aluminium purity as per E91E Grade & Current Density 0.8 A per sq. mm. compliance to IS 5082 and Enclosure fabricated with 16 SWG CRCA sheet and epoxy paint, with suitable number of ways and with SMC/DMC Insulators and accessories of suitable rating complete as per specification no. CPBB

Supplying & erecting Minimum three & above star rated Centrifugal water pump (Monoblock), 230V, Single phase 50 cycles A.C. supply of 1.5 kW/2 HP with discharge 600/140 Litres per Minute (LPM) for head of 8/22 m & 50 mm suction/ 50 mm delivery pipe on provided C.C. foundation as per specification No. WP-CGP

Supplying, installing, testing & commissioning split type room air conditioning unit 2.5TR to 2.7TR capacity with refrigerant R32 415V, 50 Hz, A.C. supply having 1 no of air handling unit (Mega split) mounting type complete with temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/WAC

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor. room air conditioning unit 1.7TR to 2.0TR capacity having ISEER minimum 5.0 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position in provided recess with wooden frame complete specification no. AP-AC/WAC

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.3TR to 1.6TR capacity having ISEER minimum 3.8 to maximum 4.39 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. APAC/ WAC

Supplying & erecting minimum three & above star rated Centrifugal water pump (Monoblock), 415 V, three phase 50 cycles A.C. supply of 7.5 KW/10 HP with discharge 1150/600 Litres per Minute (LPM) for head of 24/69 m and 65 mm suction/ 50 mm delivery pipe of size, on provided C.C. foundation as per specification No. WP-CGP

Supplying & erecting automatic control panel for 3 Phase , 415 volt, A.C, Submersible/centrifugal pump set up to 7.5 HP consisting of DOL starter having relay range 9-14 AMP,S.P.P., Combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc .

Supplying & erecting D.O.L Starter suitable for 250 V, Single phase 50 cycles with overload element with necessary materials and connected to supply up to 3 H.P.

Supplying & erecting D.O.L Starter suitable for 415 V, 3 phase 50 cycles with no volt coil and overload element with necessary materials and connected to supply for 10 H.P.

Supplying and erecting 75/80 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying and erecting static energy meter with 240V 50 Hz. AC supply 10 to 60 A, ISI mark, accuracy class 1.0 with backlit LCD display, (measuring and display kWh, kVAh, V,I,PF, frequency, kW, kVA, six months history of Energy & MD in kW & kVA ) with transparent hinge type box complete erected on polished teak wood board duly wired with required size of weather proof PVC wires duly tested by electric supply company.

Supplying and erecting static energy Trivector meter 3x240V 50 Hz. 20- 100A meter AC 3 phase 4 wires LCD/LED display (Measures & displays Trivector, V, I, kW, PF, Hz, last month history of kWh & MD in kW) with special features like TOD, Tamper logging, Optical Communication Port & Display in absence of Power complete erected on polished teak wood board duly wired with required size of weatherproof PVC wires duly tested for class 1.0 accuracy by electric supply company.

Supplying and erecting minimum Three & above star rated submersible pump set suitable for erection on open well of 5.625 KW/7.5 HP with 415 V 50 c/s. A.C. supply, having delivery head from 57 to 22 m and discharge from 120 to 900 litres. . per minute & pipe of Suction 75 mm/Delivery 65 mm diameter erected with necessary H type clamps as per specification No. WP-OSP

Supplying, installing, testing and commissioning of 5 kWp ON-GRID Solar PV System / Plant consisting Solar PV Poly Crystalline Panel (335 Wp X 15 Nos.) and Solar ON-GRID Inverter of similar capacity (THD<3%) with interconnecting wires / cables up to solar ON GRID inverter, proper base plate,canopy box to house Inverter and necessary accessories i.e. ACDB/ DCDB , MCB etc. wiring up to solar Inverter in casing and capping, display board, sign board, two distinct earthing, lightning arrester, liaisoning charges, remote monitoring system with maintaining card/chip for 5 years including net charges for RMS system, complete up to net meter installation and export to the grid with 5 year ON-SITE warranty and fully comprehensive maintenance contract as per Specification no. ESD-RT-ONG

Supplying and erecting three phase 10 to 60 A net meter DLMS compliance of accuracy class 1.0, 3 x 240V, 50 Hz, with backlit LCD display, optical port and RJ 232 port (measures import kWh, kVAh, export kWh, kVAh, Net kWh, kVAh, V, I, kW, 6 months history of energy) with wiring connections and mounting hardware on provided panels complete with calibration certificate frommanufacturer

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying and erecting PVC insulated PVC round sheathed 1.5 sq.mm (30 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Supplying and erecting mains with 3x10 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying & laying (including excavation) reinforced cement concrete pipe of IS 458:2003 NP-2 class of 150 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.

Supplying & laying (including excavation) half round reinforced cement concrete pipe of IS 458:2003 NP-2 class of 150 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.

Supplying , erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) cable 11 kV(E), 3 x 300 sq. mm. aluminium conductor laid in provided trench / pipe as per specification no. CB-HT

Supplying, installing, testing and commissioning 11 kV 630A, indoor type ring main unit with 1 VCB & 2 LBS with internal arc compliance complete erected on provided CC foundation/MS channels/trench, etc., as per specification no SW-HTS / RMU

Providing and erecting Heat shrinkable straight through joint kit for 11 kV ( E ) XLPE HT cable 3x up to 95 sq. mm. with necessary material as per specification no. CB-JT/HT

Providing and erecting Heat shrinkable straight through joint kit for 11 kV ( E ) XLPE HT cable 3x240 to 400 sq. mm. with necessary material as per specification no. CB-JT/HT

Supplying , erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) cable 11 kV(E), 3 x 95 sq. mm. aluminium conductor laid in provided trench / pipe as per specification no. CB-HT

Providing and erecting Heat shrinkable indoor termination kit for 11 kV ( E ) XLPE HT cable 3x up to 95 sq. mm. with necessary material as per specification no. CB-JT/HT

Providing and erecting Heat shrinkable indoor termination kit for 11 kV ( E ) XLPE HT cable 3x240 to 300 sq. mm. with necessary material as per specification no. CB-JT/HT

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 150 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 240 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting fencing of section having size 2450 mm in height from ground level and 1200 mm width with angle iron frame work erected in CC foundation and painted complete as per specification no SS-AS/FSG

Supplying, erecting, testing and commissioning 11KV HT metering cubical (compact / vertical type) approved by MSEDCL / licensee fabricated with 2 mm (14 SWG) M.S. sheets with supporting angle, painted with powder coating /epoxy paint of required shade, copper bus bar size 25 x 6 mm, heavy duty mechanical lock, with counter meter for measuring no of times the opening of meter door, top side cover (CT, PT cover) interlock with meter door, epoxy casted 3 nos. CT having required ratio between 50/5A to 200/5A, VA 10 or 15, Class 0.2S, epoxy casted 3 nos. PT having ratio 11000/V3/110/V3 VA 50, Class 0.2suitable for provided trivector meter, and provision for incoming and outgoingcables complete duly tested by licensee with necessary test certificates and erected on provided plinth/ cc foundation.

SITC of high quality multicolor spotlight, Power : 20W, Colour: RGB , Protection Rating : IP65, Beam Angle : 20°/45°, Body : Die casted, additional wall mount arrangements for fixing the lights. Optics: Specially designed to minimize hot spots & fringing in color mixing applications. Power Input : DC 24V (without DC Driver)

SITC of high quality long throw multi-color linear wash light, Protection Rating IP65, complying to BIS standard IS 10322 (Part 5/Sec 1): 2012, and having CE certification against standard EN 61547: 2009, EN 60598-1:2015, and EN 61347- 2-13:2014.Mounting Structure : Additional wall mount yoke arrangements for fixing the lights. Rotation view : Inbuilt body rotating angle in degrees punched in the yoke/rear sides for uniform rotation angle to get the desired effect. Power consumption : SOW, CCT : RGB , (as per the design approval) Beam Angle 25°X25°, Control DMX 512, Channel 4 CH, Body Die casted / extruded aluminium, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications.

Supplying & erecting Decorative light pole of height 4 m high (clear height) with decorative double bracket made out MS Pipe as per lS1161:1998 .The Pole will have provision for in built junction box weather proof flush door & locking arrangement for housing at bottom of the dia. of the pole shall be 140 mm & top section dia of 76 mm and base plate dimensions 250x250x10 mm thick and bottom and middle pepole shall be provided with cast iron /Aluminium embellishment to add aesthetic on the pole with the help of grub screw .The body of the decorative pole and bracket will be duly painted in U.V ray resistant PU coating in approved colour shade. The coating should have a DFT of 50 microns .The final design shall be got approved from

Supplying & erecting Decorative light pole of height 3 m high (clear height) with Single Arm decorative bracket made out GI Pipe as per lS1161:1998 .The Pole will have provision for in built junction box weather proof flush door & locking arrangement for housing at bottom of the dia. of the pole shall be 140 mm & top section dia of 76 mm and base plate dimensions 250x250x10 mm thick and bottom and middle pipe of the pole shall be provided with cast iron /AIuminium embellishment to add aesthetic on the pole with the help of grub screw .The body of the decorative pole and bracket will be duly painted in U.V ray resistant PU coating in approved colour shade. The coating should have a DFT of 50 microns .The final design shall be got approved from Engineer in charge.

Supplying & erecting Decorative light pole of height 3 m high (clear height) with double Arm decorative bracket made out GI Pipe as per IS1161:1998 .The Pole will have provision for in built junction box weather proof flush door & locking arrangement for housing at bottom of the dia. of the pole shall be 140 mm & top section dia of 76 mm and base plate dimensions 250x250x10 mm thick and bottom and middle pipe of the pole shall be provided with cast iron IAluminium embellishment to add aesthetic on the pole with the help of grub screw .The body of the decorative pole and bracket will be duly painted in U.V ray resistant PU coating in approved colour shade. The coating should have a DFT of 50 microns .The final design shall be got approved from Engineer in charge.

Supply of 3mts decorative POLYSTEEL LAMP POST shall be made using FRP for outer cover as per requirement (Fiber reinforced marine grade polymer) inner section fabricated with 60MM OD GI pipe as per ISI1239\1161. Overall height of the pole including light fixture will be 3.5 mtr. Base plate as per ISI 2062 E250 grade size 430 diameter x10mm thick. The pole will be supplied with a Four Arm bracket and post top arrangement in center. The length of the top arm shall be 530 mm. FRP material shall be marine grade composite consisting of GSM 450 E AND 300 GSM , DENSITY 450 GMS/m2 and 300gms /m2 The overall thickness of the FRP base will be 2mm to 3 8km. The pole shall have a weatherproof flush door and locking arrangement for housing at the bottom of the pole junction box. It will accommodate 6amps mcb on bakelite sheet and heavy duty 32 amps connector suitable upto 4cx16/25sqmm al cable. The pole base plate shall be suitable for M16 x 600 mm J bolt . The pole base is 370mm dia and height of base is 775mm. The decorative element sze is 370mm height and max. dia 200 mm. The Sleeve of pole is fluted and diameter is 100 mm. Arm pipe is 25 mm OD attached with decorative corbel. The polysteel decorative lamppost will be pre-treated and duly painted with UV stabilized Polyurethane Aliphatic paint of approved colour shade

Supply testing commissioning of DMX controlIer,2 ports output which can control 2048 plus DMX pixels. It shall support Off-line control & play back content stored in the SD card up to 64GB and also I support at least 50 different scenes. It should be with 15digital touch screen display for changing modes, it supports master slave configuration to accommodate more DMX addresses (8x512 pixels Slave device) with outdoor enclosure to protect from sunlight, dust and water

Supply ,Installation, Testing and Commissioning of 24V 5W RGBW or single colour as per requirement, DMX addressable Dot (Coin) with built-in decoder 16along with lP66 with clear/milky diffuser , arrangement for connecting supply and control signal cable complete with all fixing mechanism such as screw or silicon gum. The coin shall have chipset of Cree/Osram/Bridgelux

Providing & erecting 7 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

SITC of 90W Street light luminaire including all necessary labour material etc. complete and approved by the Engineer in charge

Supply of decorative luminaire made of spun aluminium body with pressure die-cast heat management (PDCHM) and the IP65 optical compartment with high power LED/s is comprised of a deep drawn chemically polished and co-extruded, thermofrmed ploycarbonate protector stabilized agent UV rays suitable for 40W LED. Fitting should be post top mounting type decorative fixture. fitting should have decorative elements to be placed on top of the ficture for asthetic purpose. Fitting should have inbuilt driver with efficiency >0.9 and having surge protection device of 4KVA and external surge protection device of 10KVA, colour temperature 3000K / 4000K / 5700K Natural day light LED.LED's to be of Osram / Cree / Bridgelux & driver to be of make Philips / fulham / Osram

SITC of Decorative hanging type LED decorative light fitting made of Alum Die Cast – 60W/70W, with pressure die-cast heat management (PDCHM) and the IP65 optical compartment with high power LED/s , colour temp shall be 4000k with permissible tolerance .Fitting should have inbuilt driver with efficiency >0.9 and having surge protection device of 4KVA and external surge protection device of 10KVA, colour temperature 3000K / 4000K / 5700K Natural day light LED.LED's to be of Osram / Cree / Bridgelux & driver to be of make Philips / fulham / Osram.

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole).

S u p p l y i n g & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

Supplying, installation, testing and commissioning of 4.0 MP full HD video resolution 2560x 1440, 25 fps True D/N IR Bullet/ Box camera, 2.8-12 mm motorised lens, Auto Back Focus, High Light compensation, 120 dB and above True WDR, audio capture capability, 4 streams, H.264/H.265, ONVIF compliant,SD card Slot, with IP66 housing and mount with dehumidification feature with accessories such as mounting brackets/structures /fixtures etc. necessary to mount the camera on pole, etc. Video coding H.264 / H.265, Certification from EN, UL&CE,FCC. Tested in India from any reputed test laboratories/ Institute/ University/BIS for

Supply Installation Testing & commissionino Of Network Video Recorder 32 channel input, Support tch HDMI Up to 12 Megapixels resolution recording, Support RAID 0, I, 5, 6, I & 8 SAT A HDDs, Up to 8TB for each HDD, Supp01t N+ 1 Hot spare, Support for 12V Po~er output, HDMWGA Output, Recording Resolution, Resolution 12MP/ 6MP/5MP/4MP/3MP/I080p /960p/720p /Dl/2CIF/CIF, Compression H.265/H.264, 8 SATA interfaces, Capacity up to 8TB for each HDDs, Array Type RAID 0, 1, 5, 6, 10.

Supply Installation Testing & commissioning of 6000 GB Hard Disk for video Surveillance Equivalent to:- Western Digital.

Supply, installation, testing & commissioning of 4MP IP Dome/Bullet Camera with 1/2.8", progressive scan, CMOS, 2-8l4/6mm lens@ Fl.8/2.0, angle of view more than 82° WDR. 120db or above, Illumination Colour: 0.02 Lux (FI.8), 0.0Lux with lR ,Day/Night with auto switch ICR, ,supported H.264/H.265 MJPEG video compression ,Video triple Streaming,Smart function supported ( motion , IP 66 CE ROHS)

Supply, Installation,Testing & Commissioning of IP PTZ camera with HD1080P 2.1MP Resolution, 20x optical zoom, 16X Digital zoom , Day/Night, Wide dynamic range,Dual H.264 streaming, 0.05 lux, vandal resistant, 360° continuous pan, -5° to +95° tilt, 300 preset, 4 tours, IP66 rated with built in heater and blower, Mounted on Wall/Pole as per site requirement (including required accessories), UL listed as per detailed specifications. Camera Shall be ONVIF compliant

Supply Installation Testing & commissioning of 43 "TV Eauivalent to:- LG / Samsung.

Supply, Installation, Testing & commissioning of Hot dipped galvanised, round shape steel pole for installation of PTZ Camera and Outdoor Dome Camera, length 6 meters, diameter 4 inches (Nominal bore) Medium class, ISIS marked to IS:1239 with latest amdts and with atleast 1 Meter below ground with grouting.

SITC of 1IN/4OUT Video Splitter for additional viewing

S & i of 16CH NVR with 2 HDD bay

Supplying, fixing, and configuring 24 ports, PoE switch compliant with IEEE 802.3 standards with min. 193W PoE capacity with 4GE SFP uplink in provided rack as per specification no. WG-NWC/ENS

Supplying & erecting UPS of !KV A capacity complete with standard features, along with necessary SMF batteries for 20 mins. batterv backuo

Supplying, erecting, testing and commissioning of 10kVA capacity online pure sine wave with backup time of ....... hrs. PWM & IGBT based UPS with 0.9 to unity output pf, 3 phase input & 1 phase output complete with all protections as per specification no. AP-UPS

Supplying, erecting, testing and commissioning of 20kVA capacity online pure sine wave, with backup time of ....... hrs. PWM & IGBT based UPS with 0.9 to unity output pf, 3 phase input and 3 phase output complete with all protections as per specification no. AP-UPS

S.I.T.C. of 3 Chip DLP Laser Projector, Brightness: 27000 Lumens or more, Resolution: Native 4K or better, along with the appropriate Lens to manage the throw distance, 3D ready, Native aspect ratio 16:10, Horizontal & vertical edge blending, Motorised Zoom & Focus, Motorised Lens shift H/V, Sealed DLP™ core, Standard Orientation : 360°, DMX 512 Standard WARP Direct adjust OSD + toolset, Image processing, Embedded warp & blend, 3D Active eye wear (optional), passive circular (optional); 2 flash up to 200Hz; optional Dual Eye Point 240Hz, Single HDBaseT; HDMI2.0 (HDCP2.2, HDR10); DP 1.2 (HDCP1.3); Quad 3G/12G SDI/BarcoLink ULTRA, supplied with DP input cards, IR, RS232, IP (RJ45 Network connection), direct Android app to control, MAKE/BRAND: Barco/Panasonic / Christie

S.I.T.C. of Smart poles of 10 mtrs heights Customized enclosure for above projector with pole mounting arragement IP68 protection and security. Each enclosure allow to put minimum 1 projector, White in color, easy maintenable Make: Techvisio/ Mapan/Aura / LM3X [Urban pole / Valmount structurs.

SITC of Enclosure for projecors with proper ventilation MAKE/BRAND: Proietta / DMI / TARM

S.I.T.C. of Display media server with 4nos x HD outputs as required , synced together. . Min. 1x NVidia Quadro RTXA5000 graphic processor, PC i9-13900K / RTX 5000 / 64 GB DDR5 / 2 TB NVME / P2722H Monitor, Processor : 13th Generation Intel Core i9-13900K (36MB Cache, 24 Core (8+16), 3.0GHz to 5.8GHz (125W)) TDP, Processor VR Heatsink Premium CPU Liquid Cooler, Dell Premier Color 6.1, .Chassis Options Precision 3660 Tower with 1000W (80 Plus Platinum) PSU, RPL and ADL Compatible, V2, .Memory 64GB, 2x32GB, DDR5 up to 4400MHz UDIMM non-ECC memory, Video Card Nvidia GeForce RTX 4090, 24GB GDDR6, HDMI, 3 DP, .Keyboard & Mouse, , (Integrated NIC included) + Additional 2.5G Ethernet LAN (RJ45) Port Intel i225 ( Dual LAN), M.2 NVMe SSD 2TB PCIe NVMe Class 40 M.2 SSD 400-BNGN 1, Thermal Cooling Premium CPU Liquid Cooler 412-ABBT 1 Built -In Software : Waves Maxx Audio, Dell Precision TPM / Operating System Windows 11 Pro, English 619-APTO 1 12.to be supplied with 27" Monitor x 2 Nos. to be supplied with 3 - years Dell next day on site support warranty. to be supplied with standard accesories like Lan Cable / Power Cable / 4K Hdmi Cable / Large Mouse Pad / Dual Band Usb Wifi And Bluetooth Adapter. MAKE/BRAND: DELL PRECISION WORKSTATION 3660 TOWER WITH RTX 4090 equivalent in HP / Lenovo / Asus

S.I.T.C. of Production PC i9-13900K / RTX 4090 / 64 GB DDR5 / 2 TB NVME / P2722H Monitor, Processor : 13th Generation Intel Core i9-13900K (36MB Cache, 24 Core (8+16), 3.0GHz to 5.8GHz (125W)) TDP, Processor VR Heatsink Premium CPU Liquid Cooler Dell Premier Color 6.1, .Chassis Options Precision 3660 Tower with 1000W (80 Plus Platinum) PSU, RPL and ADL Compatible, V2, .Memory 64GB, 2x32GB, DDR5 up to 4400MHz UDIMM non-ECC memory, Video Card Nvidia GeForce RTX 4090, 24GB GDDR6, HDMI, 3 DP, .Keyboard & Mouse, , (Integrated NIC included) + Additional 2.5G Ethernet LAN (RJ45) Port Intel i225 ( Dual LAN), M.2 NVMe SSD 2TB PCIe NVMe Class 40 M.2 SSD 400-BNGN 1, Thermal Cooling Premium CPU Liquid Cooler 412-ABBT 1Built -In Software :Waves Maxx Audio, Dell Precision TPM / Operating System Windows 11 Pro, English 619-APTO 1 12.to be supplied with 27" Monitor x 2 Nos. to be supplied with 3 - years Dell next day on site support warranty.to be supplied with standard accesories like Lan Cable / Power Cable / 4K Hdmi Cable / Large Mouse Pad / Dual Band Usb Wifi And Bluetooth Adapter. MAKE/BRAND: DELL PRECISION WORKSTATION 3660 TOWER WITH RTX 4090 equivalent in HP / Lenovo / Asus

S.I.T.C. of 3D Projection mapping software, Playback control System to manage, schedule & control the media servers, watchout software should work best in above system MAKE/BRAND: Dataton/ Resolume/ Disguise / Pixera

SITC of Point-source FOH speakers, dual 8" FOH speakers, Install outdoors with an IP55 weather rating, three-layer stainless steel grille, water-resistant woofer cone coating, industrial polyurethane exterior coating, and molded cover to protect inputs, EN 54-24 Certified: EN 54-24: 2008, Provide wide, even coverage with 90° × 60° constant-directivity high-frequency horn, which can be rotated for horizontal or vertical installation, Low Frequency 2 × Bose LF8 high-excursion 8-inch woofers (2-inch voice coil), High Frequency 1 × extended high-frequency compression driver (2-inch voice coil), Nominal Impedance 8 Ω, with 70v/100v tapping, Frequency Response (–3 dB) 1 80 Hz to 16 kHz, Frequency Range (–10 dB) 70 Hz to 18 kHz, Sensitivity 97dB for Horizontal / vertical installation above 8 feets, to be supplied with standard mounting accessories to mount the same on Truss. MAKE/BRAND: BOSE AMU208 or equivalent in TW Audio / L-Acoustics

SITC of Outdoor Subwoofer with Drivers 2x 10" Low Frequncy drivers, Exterior-grade plywood enclosure with compact size for installations, Install outdoors with an IP55 weather rating, three-layer stainless steel grille, water-resistant coating on woofer cone, industrial polyurea exterior coating, and molded cover to protect inputs, Frequency Response (+/-3 dB) 45 Hz to 180 Hz, Nominal coverage (H x V) Omnidirectional below 200 Hz, Power Handling, peak 2000W, Maximum SPL @ 1m 117 db Free Field 123 db Wall/Ceiling, Nominal Impedance 8 Ω, Frequency Range (-10 dB)37 Hz to 270 Hz, Power Handling, long-term continuous 500 W, Sensitivity 96 db Wall/Ceiling, Maximum SPL @ 1m, peak 129 db Wall/Ceiling, to be supplied with standard mounting accessories to mount subwoofers on Truss MAKE/BRAND: BOSE MB210-WR Outdoor Subwoofer or equivalent in TW Audio / L-Acoustics

SITC of Four Channel amplifier with inbuilt DSP & Power share technology, Total power @ 4800 watts, 1200W @8ohm per channel @ 4 channel, with power sharing technology, Should have flexibility to share the total power across 4 channel at Nomiral impedence, with DANTE port, 4 Analog inputs, or 4 Channel DANTE inputs, MAKE/BRAND: Bose PowerShareX PSX4804D or Equivalent in TW Audio / Powersoft / L-Acoustics / LAB-Gruppen

SITC of programmable 8 inputs DSP with DNATE interface, Open-architecture, 1RU design built for general-purpose and PA applications, USB connection facilitates easy integration with PC audio sources, Dante audio networking supports 64 x 64 audio channels for connection to other Dante-enabled products, Front-panel interface features a large OLED display and rotary encoder for setting network parameters and monitoring channel activity, GPIO (5 in/5 out) and Serial for interfacing with external devices and control systems, Signal Processor 32-bit fixed/floating-point DSP 456 MHz/ARM Cortex-A8 600 MHz, Frequency Response 20 Hz to 20 kHz (+0.3 dB/-0.1 dB), Dynamic Range > 115 dB A-weighted 20 Hz – 20 kHz, analogy input to analog output, Input Channels 12 balanced, mic/line level, Output Channels 8 balanced, line level, EQ./ Feedback / Noise cancellation / Crossover all setting programmeble mixer MAKE/BRAND: BOSE ControlSpace EX-1280 or Equivalent in QSC / symmetrics / Bi-Amp

SITC of Wirless Handheld microphone set, Microphone set consists of Handheld mic with built in transmitter, & receiver, true diversity, Speechline Series Microphone set with 2 channel mic receiver connects over DANTE to avoid long Audio cables. MAKE/BRAND: Sennheiser SL Handheld DW-4 (1 Nos) + SL MCR 2 DW-3 + AWM 4 OR Equivalent in Shure / Audix

SITC of 304 Grade steel Speaker enclosures for safety of speakers MAKE/BRAND: Customized

S.I.T.C. of Long distance transmitter for High resolution signals, Transmits HDMI, USB data, control, and analog audio up to 330' (100 m) over a shielded CAT 6A cable Supports computer and video resolutions up to 4K/60 @ 4:4:4, USB 2.0 extension, Analog stereo audio embedding, HDCP 2.3 compliant, Supported HDMI 2.0b specification features include data rates up to 18 Gbps, HDR, Deep Color up to 12‑bit, 3D, and HD lossless audio formats MAKE/BRAND: Extron DTP3 T 301 Or Equivalent in Lightware / Crestron

S.I.T.C. of Long distance Receiver for High resolution signals, Receives HDMI, USB data, control, and analog audio up to 330' (100 m) over a shielded CAT 6A cable Supports computer and video resolutions up to 4K/60 @ 4:4:4, USB 2.0 extension, Analog stereo audio embedding, HDCP 2.3 compliant, Supported HDMI 2.0b specification features include data rates up to 18 Gbps, HDR, Deep Color up to 12‑bit, 3D, and HD lossless audio formats MAKE/BRAND: Extron DTP3 R 301 Or Equivalent in Lightware / Crestron

SITC of 4k enabled HDMI male to male cables, of 2 mtrs, Ultra-flexible HDMI cables Conforms to Premium High Speed HDMI cable performance standards 4K/60 verified MAKE/BRAND: Extron, HDMI Ultra/6 or Equivalent in Crestron / Lightware / Sony

SITC of 30 mtr / 100ft High speed 4k HDMI cable, HDMI Premium High Speed Optical Cables - Plenum, Conforms to Premium High Speed HDMI Cable performance standards Flexible, ultra-thin 0.16” (4 mm) diameter cable Plenum, NEC CMP‑rated cable No external power is needed, Highly resistant to EMI/RFI interference, Color-coded and labeled ends MAKE/BRAND: Extron HD Pro P/100 or Equivalent in Crestron / Lightware / Sony

SITC of 24 port Non -POE managed Ethernet switch, Stackable Managed Switch | 24 Ports 10 Gigabit Ethernet (GbE) | 20 Ports 10GBase-T | 4 x 10G Combo SFP+ | L3 Dynamic Routing. MAKE/BRAND: Cisco SX550X-24 or equivalent into Above system compatible products

Supply & laying of CAT6 cable, Armored LAN Cables are underground or outdoor all weather proof cabling that offers lowest signal loss and supports Gigabit Ethernet (1000Base-T) standard that operates at 250MHz. It should work on full duplex mode, comes with 23AWG twisting and are further insulated with HDPE and FR-PVC and Aluminum Wire Armoring, UL Listed, ETL, EIA/TIA C.2 verified, Should support 2.5Gbps, 5Gbps and 10Gbps at limited distances with compatible devices. MAKE/BRAND: Belden / Proel / percon

Supply & laying of Speaker cable, 2.5 Sqr mm Armoured 2 core copper cable for outdoor laying in PVC FRLS conduits, MAKE/BRAND: Belden / Proel / percon or Equivalent in Polycom / RR Kablel /GM

SITC of AV 19" standard rack, 32ux 1000 x 1000 to be supplied with front Galss door, side doors, rear doors, 2 Nos of FANs on top for ventilation, 2 x PDUs of 6 sockets of 6 Amp, with Power prtected by MCB, appropriate numbers of Rack hardware, cable manager, 4 Nos of caster wheels for easy rack movements, 3 Nos of Full width & dpeth blank shelfs, & other required accessories MAKE/BRAND: W&Q / Valrack / Netrack

SITC & programming of Automation processor with Minimum Six bidirectional RS-232 serial ports with software handshaking, Two bidirectional RS-232/RS-422/RS-485 serial ports with hardware and software handshaking, Eight IR/Serial ports for one-way control of external devices, 1 X Ethernet port, 8 x Relay ports, 4 x input/output ports, single-core processor and memory with 1 GB of RAM and 8 GB of Flash, Ethernet monitoring MAKE/BRAND: Extron IPCP Pro550 xi or Equivalent in Crestron

SITC of wired 7" Touch panel, to be used as User interface to control & manage all devices, 7" capacitive touchscreen with 1024x600 resolution and 24-bit color depth, Gorilla Glass® screen is tough, scratch and smudge-resistant, Faster, quad-core processing and eight times more memory, Can be mounted in a two-gang junction box, or on a wall, lectern, or any flat surface, including glass, to be supplied with all wall mount accessories & Power over Ethernet module. MAKE/BRAND: Extron TLP Pro725M or Equivalent in Crestron

SITC of Wifi accesspoints, 1.27Gbps aggregate wireless throughput and 2×Gigabit wireline ports, Dual-band 2×2:2 MUMIMO with beam-forming technology Self power adaptation upon auto detection of PoE or PoE+, Supports 100+ concurrent Wi-Fi client devices, Up to 250-meter coverage range. MAKE/BRAND: Grand stream india / CISCO / TP Link or equivalent

SITC of other accessories like connectors, small patch cables of CAT6 / audio etc, sleevs, DP to HDMI or HDMI to DP, etc adapters MAKE/BRAND: Various

SITC of Smart Cinema Projector : Native brightness 17,000 lumens (typical) Native contrast ratio : 2300:1 (typical) up to 3000:1 with HC lens Digital MicroMirror Device™ 3x 0.98” DC4K Resolution native 4K: 4096 x 2160 Color gamut : DCI P3 compliant (98.5% of Rec.2020; when measured in xy-color coordinates) Light source : Laser Prime lenses With C-lensholder: 0.8 - 1.16; 1.09 - 1.40; 1.2 - 1.8; 1.4 - 2.05; 1.6 - 2.5 ; 1.95 - 3.2; 2.4 - 3.9 With B-lensholder: 1.01; 1.27; 1.6 – 2.4; 1.9 – 2.6; 2.0 – 2.95; 2.3 – 3.65; 2.8 – 4.7; 3.55 – 6.95, Long-term brightness stability : 40,000 hrs @ average usage conditions, Housing integrated cooling design and patented sealed optical assembly Dimensions (WxLxH) MAKE/BRAND: Barco/Panasonic / Christie

S.I.T.C. of Perforated Acoustically transparent curved screen, fixed frame with Black borders, matt Silver 3D surface, Size of the screen 15 mtr wide x 4 mtr height in curved cinema grade screen MAKE/BRAND: Customised

S.I.T.C. of Production PC i9-13900K / RTX 4090 / 64 GB DDR5 / 2 TB NVME / P2722H Monitor, Processor : 13th Generation Intel Core i9-13900K (36MB Cache, 24 Core (8+16), 3.0GHz to 5.8GHz (125W)) TDP, Processor VR Heatsink Premium CPU Liquid Cooler, Dell Premier Color 6.1, .Chassis Options Precision 3660 Tower with 1000W (80 Plus Platinum) PSU, RPL and ADL Compatible, V2, .Memory 64GB, 2x32GB, DDR5 up to 4400MHz UDIMM non-ECC memory, Video Card Nvidia GeForce RTX 4090, 24GB GDDR6, HDMI, 3 DP, .Keyboard & Mouse, , (Integrated NIC included) + Additional 2.5G Ethernet LAN (RJ45) Port Intel i225 ( Dual LAN), M.2 NVMe SSD 2TB PCIe NVMe Class 40 M.2 SSD 400-BNGN 1, Thermal Cooling Premium CPU Liquid Cooler 412-ABBT 1 Built -In Software :Waves Maxx Audio, Dell Precision TPM / Operating System Windows 11 Pro, English 619-APTO 112.to be supplied with 27" Monitor x 2 Nos.to be supplied with 3 - years Dell next day on site support warranty. to be supplied with standard accesories like Lan Cable / Power Cable / 4K Hdmi Cable / Large Mouse Pad / Dual Band Usb Wifi And Bluetooth Adapter. MAKE/BRAND: DELL PRECISION WORKSTATION 3660 TOWER WITH

S.I.T.C. of Active Stereo 3D Glasses along with 1 x RF/IR emitter

SITC of Point screen array speakers to be placed behind the screen, Horn loaded speakers with subwoofers, Two-Way High Performance ScreenArray® Cinema Loudspeaker, should be low in depth max. 15' dpeth, LF Power Handling (2Hr AES Rating)1200W, LF Power Rating (100Hr AES Rating) 720W, HF Power Handling (2Hr AES Rating) 85W, Freq. response 44Hz - 18kHz MAKE/BRAND: Harman C222HP or Equivalent in QSC

SITC of Surrfound sound speakers, 10-inch transducer, 2-way configuration 260W rated power, 8Ω impedance allows multiple surround speakers to be wired to a single amplifier channel 110° x 90° (horizontal x vertical) coverage, Cabinet features 20° down-angled front baffle, 125 dB peak SPL, Throw capability of up to 40 ft (12 m) Frequency response: 55 Hz–18 kHz (-10 dB) (4π) [2 left + 2 right + 2 Rear MAKE/BRAND: Harman 8102 or Equivalent in QSC

SITC of Amplifier dual channel, Automatic presets for popular JBL cinema speaker systems for quick, easy configuration, Intuitive front-panel LCD screen guides installers through setup, Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting, Computer connectivity via USB allows fast setup and configuration with HiQnet™ System Architect™ software, 1200 watts @ 4ohms per channel, MAKE/BRAND: harman DSi4000 or Equivalent in QSC

SITC of Cinema processor 5.1 channel, with 5.1 channel pre-amplifier outputs, with min. 4 HDMI inputs, & optical Audio inputs , DOLBY DTS-X certified AV receiver MAKE/BRAND: Harman kardon / Marantz / Denon

SITC of Wirless Headworn microphone set, Microphone set consists of Handheld mic with built in transmitter, & receiver, true diversity, Speechline Series Microphone set with 2 channel mic receiver connects over DANTE to avoid long Audio cables MAKE/BRAND: Sennheiser SL Lapel DW-4 (1 Nos) + SL MCR 2 DW-3 + AWM 4 OR Equivalent in Shure / Audix

SITC of 12 channel Digital manual mixer with interface on IPAD / PC or Android panel, 4 award-winning midas-designed, fully programmable mic preamps for audiophile sound quality, Auto-Mixing automatically manages microphone gain sharing, USB connector for uncompressed stereo WAV recording and playback, MAKE/BRAND: Behringer / Soundcraft / Midas

S.I.T.C. of Long distance transmitter for High resolution signals, Transmits HDMI, USB data, control, and analog audio up to 330' (100 m) over a shielded CAT 6A cableSupports computer and video resolutions up to 4K/60 @ 4:4:4, USB 2.0 extension, Analog stereo audio embedding, HDCP 2.3 compliant, Supported HDMI 2.0b specification features include data rates up to 18 Gbps, HDR, Deep Color up to 12‑bit, 3D, and HD lossless audio formats MAKE/BRAND: Extron DTP3 T 301 Or Equivalent in Lightware / Crestron

S.I.T.C. of Long distance Receiver for High resolution signals, Receives HDMI, USB data, control, and analog audio up to 330' (100 m) over a shielded CAT 6A cable Supports computer and video resolutions up to 4K/60 @ 4:4:4, USB 2.0 extension, Analog stereSupports computer and video resolutions up to 4K/60 @ 4:4:4, USB 2.0 extension, Analog stereo audio embedding, HDCP 2.3 compliant, Supported HDMI 2.0b specification features include data rates up to 18 Gbps, HDR, Deep Color up to 12‑bit, 3D, and HD lossless audio formats MAKE/BRAND: Extron DTP3 R 301 Or Equivalent in Lightware / Crestron

SITC of 30 mtr / 100ft High speed 4k HDMI cable, HDMI Premium High Speed Optical Cables - Plenum, Conforms to Premium High Speed HDMI Cable performance standards Flexible, ultra-thin 0.16” (4 mm) diameter cable Plenum, NEC CMP‑rated cableNo external power is needed, Highly resistant to EMI/RFI interference, Color-coded and labeled ends MAKE/BRAND: Extron HD Pro P/100 or Equivalent in Crestron / Lightware / Sony

Supply & laying of CAT6 cable, Armored LAN Cables are underground or outdoor all weather proof cabling that offers lowest signal loss and supports Gigabit Ethernet (1000Base-T) standard that operates at 250MHz. It should work on full duplex mode, comes with 23AWG twisting and are further insulated with HDPE and FR-PVC and Aluminum Wire Armoring, UL Listed, ETL, EIA/TIA C.2 verified, Should support 2.5Gbps, 5Gbps and 10Gbps at limited distances with compatible devices. MAKE/BRAND: Belden / Proel / percon

SITC of AV 19" standard rack, 32ux 1000 x 1000 to be supplied with front Galss door, side doors, rear doors, 2 Nos of FANs on top for ventilation, 2 x PDUs of 6 sockets of 6 Amp, with Power prtected by MCB, appropriate numbers of Rack hardware, cable manager, 4 Nos of caster wheels for easy rack movements, 3 Nos of Full width & dpeth blank shelfs, & other required accessories MAKE/BRAND: W&Q / Valrack / Netrack

SITC of other accessories like connectors, small patch cables of CAT6 / audio etc, sleevs, DP to HDMI or HDMI to DP, etc adapters

S.I.T.C. of single or 3 Chip DLP Laser Projector, Brightness: 22000 Lumens or more, along with the appropriate Lens to manage the throw distance, 3D ready, Native aspect ratio 16:10, Horizontal & vertical edge blending, Motorised Zoom & Focus, Motorised Lens shift H/V, Sealed DLP™ core, Standard Orientation : 360°, DMX 512 Standard WARP Direct adjust OSD + toolset, Image processing, Embedded warp & blend, 3D Active eye wear (optional), passive circular (optional); 2 flash up to 200Hz; optional Dual Eye Point 240Hz, Single HDBaseT; HDMI2.0 (HDCP2.2, HDR10); DP 1.2 (HDCP1.3); Quad 3G/12G SDI/BarcoLink ULTRA, supplied with DP input cards, IR, RS232, IP (RJ45 Network connection), direct Android app to control, MAKE/BRAND: Barco/Panasonic / Christie

S.I.T.C. of Smart poles of 10 mtrs heights Customized enclosure for above projector with pole mounting arragement IP68 protection and security. Each enclosure allow to put minimum 1 projector, White in color, easy maintenable Make: Techvisio/ Mapan/Aura / LM3X [Urban pole / Valmount structurs

S.I.T.C. of Display media server with 4nos x HD outputs as required , synced together. . Min. 1x NVidia Quadro RTXA5000 graphic processor, PC i9-13900K / RTX 5000 / 64 GB DDR5 / 2 TB NVME / P2722H Monitor, Processor : 13th Generation Intel Core i9-13900K (36MB Cache, 24 Core (8+16), 3.0GHz to 5.8GHz (125W)) TDP, Processor VR Heatsink Premium CPU Liquid Cooler, Dell Premier Color 6.1, .Chassis Options Precision 3660 Tower with 1000W (80 Plus Platinum) PSU, RPL and ADL Compatible, V2, .Memory 64GB, 2x32GB, DDR5 up to 4400MHz UDIMM non-ECC memory, Video Card Nvidia GeForce RTX 4090, 24GB GDDR6, HDMI, 3 DP, .Keyboard & Mouse, , (Integrated NIC included) + Additional 2.5G Ethernet LAN (RJ45) Port Intel i225 ( Dual LAN), M.2 NVMe SSD 2TB PCIe NVMe Class 40 M.2 SSD 400-BNGN 1, Thermal Cooling Premium CPU Liquid Cooler 412-ABBT 1Built -In Software :Waves Maxx Audio, Dell Precision TPM / Operating System Windows 11 Pro, English 619-APTO 1 12.to be supplied with 27" Monitor x 2 Nos.to be supplied with 3 - years Dell next day on site support warranty.to be supplied with standard accesories like Lan Cable / Power Cable / 4K Hdmi Cable / Large Mouse Pad / Dual Band Usb Wifi And Bluetooth Adapter. MAKE/BRAND: DELL PRECISION WORKSTATION 3660 TOWER

S.I.T.C. of Production PC i9-13900K / RTX 4090 / 64 GB DDR5 / 2 TB NVME / P2722H Monitor, Processor : 13th Generation Intel Core i9-13900K (36MB Cache, 24 Core (8+16), 3.0GHz to 5.8GHz (125W)) TDP, Processor VR Heatsink Premium CPU Liquid Cooler, Dell Premier Color 6.1, .Chassis Options Precision 3660 Tower with 1000W (80 Plus Platinum) PSU, RPL and ADL Compatible, V2, .Memory 64GB, 2x32GB, DDR5 up to 4400MHz UDIMM non-ECC memory, Video Card Nvidia GeForce RTX 4090, 24GB GDDR6, HDMI, 3 DP, .Keyboard & Mouse, , (Integrated NIC included) + Additional 2.5G Ethernet LAN (RJ45) Port Intel i225 ( Dual LAN), M.2 NVMe SSD 2TB PCIe NVMe Class 40 M.2 SSD 400-BNGN 1, Thermal Cooling Premium CPU Liquid Cooler 412-ABBT 1 Built -In Software :Waves Maxx Audio, Dell Precision TPM / Operating System Windows 11 Pro, English 619-APTO 112.to be supplied with 27" Monitor x 2 Nos.to be supplied with 3 - years Dell next day on site support warranty.to be supplied with standard accesories like Lan Cable / Power Cable / 4K Hdmi Cable / Large Mouse Pad / Dual Band Usb Wifi And Bluetooth Adapter. MAKE/BRAND: DELL PRECISION WORKSTATION 3660 TOWER WITH RTX 4090 equivalent in HP / Lenovo / Asus

S.I.T.C. of 3D Projection mapping software, Playback control System to manage, schedule & control the media servers, watchout software should work best in above system MAKE/BRAND: Dataton/ Resolume/ Disguise / Pixera

S.I.T.C. of Long distance transmitter for High resolution signals, Transmits HDMI, USB data, control, and analog audio up to 330' (100 m) over a shielded CAT 6A cable Supports computer and video resolutions up to 4K/60 @ 4:4:4, USB 2.0 extension, Analog stereo audio embedding, HDCP 2.3 compliant, Supported HDMI 2.0b specification features include data rates up to 18 Gbps, HDR, Deep Color up to 12‑bit, 3D, and HD lossless audio formats MAKE/BRAND: Extron DTP3 T 301 Or Equivalent in Lightware / Crestron

S.I.T.C. of Long distance Receiver for High resolution signals, Receives HDMI, USB data, control, and analog audio up to 330' (100 m) over a shielded CAT 6A cable Supports computer and video resolutions up to 4K/60 @ 4:4:4, USB 2.0 extension, Analog stereo audio embedding, HDCP 2.3 compliant, Supported HDMI 2.0b specification features include data rates up to 18 Gbps, HDR, Deep Color up to 12‑bit, 3D, and HD lossless audio formats MAKE/BRAND: Extron DTP3 R 301 Or Equivalent in Lightware / Crestron

SITC of 30 mtr / 100ft High speed 4k HDMI cable, HDMI Premium High Speed Optical Cables - Plenum, Conforms to Premium High Speed HDMI Cable performance standards Flexible, ultra-thin 0.16” (4 mm) diameter cable Plenum, NEC CMP‑rated cable No external power is needed, Highly resistant to EMI/RFI interference, Color-coded and labeled ends MAKE/BRAND: Extron HD Pro P/100 or Equivalent in Crestron / Lightware / Sony

SITC of 100 watt fog machine MAKE/BRAND: Techvisio / aura / Havells

S.I.T.C. of GOBO PROJECTOR250-350 Watt,LED,IP 65 Gobo Projector:Body made of Diecast Aluminium. Uses high power white LED chip,7°-40°(electronic linear zoom),Display-On board Control, Gobo-7 Gobos(single colour), Gobo-flow effect, Gobo shake, Bi-directional rotation.Colours-One color wheel (7 colour+White, Rainbow flow effect),Prism-16 prism with bi-directional rotation, , Speed adjustable,Focus-Motorized linear focus.Nos.of DMX channel Light fixture should be standard DMX512 protocol compatible, the DMX decoder function should be inbuilt the light fixture,Each light fixture should be invidually addressable & should be able to operate with any standard DMX512 equipment. In-Built Electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection.Lifetime is 50,000 hours.IP rating-IP 65 minimum.Length-480mm,Width- 410mm, Height-640mm Weight -39Kgs. MAKE/BRAND: Aura / Bajaj / GM / Martin. S.I.T.C. of GOBO PROJECTOR 150 Watt,LED,IP 65

Gobo Projector:Body made of Diecast Aluminium. Uses high power white LED chip,7°-40°(electronic linear zoom),Display-On board Control, Gobo-7 Gobos(single colour), Gobo-flow effect, Gobo shake, Bi-directional rotation.Colours-One color wheel (7 colour+White, Rainbow flow effect),Prism-16 prism with bi-directional rotation, , Speed adjustable,Focus-Motorized linear focus.Nos.of DMX Channels Light fixture should be standard DMX512 protocol compatible, the DMX decoder function should be inbuilt the light fixture,Each light fixture should be invidually addressable & should be able to operate with any standard DMX512 equipment. In-Built Electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection.Lifetime is 50,000 hours.IP rating-IP 65 minimum. MAKE/BRAND: Aura / Bajaj / GM / Martin.

S.I.T.C. of DMX Controll System MAKE/BRAND: Aura / Bajaj / GM / Martin.

S.I.T.C. of 6m height pole made in combination of mild steel pipe sections 114mm dia. & 76mm dia. with suitable fixing arrangement to mount Laser projector. The pole to be provided with a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation.After Fabrication, Entire Pole is hot dip galvanized(100 microns Minimum ) for the effective corrosion resistance. The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & it's parts are painted in 3 layer coating (coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint. MAKE/BRAND: Aura / Bajaj / GM / Martin.

S.I.T.C. of Smart poles of 8 /10 mtrs heights Customized enclosure for above projector with pole mounting arragement IP65 protection and security. Each enclosure allow to put minimum 1 projector, White in color, easy maintenable Make: Techvisio/ Mapan/Aura / LM3X [Urban pole / Valmount structurs

S.I.T.C. of Display media server with 4nos x HD outputs as required , synced together. . Min. 1x NVidia Quadro RTXA5000 graphic processor, MAKE/BRAND: Asus/HP/Dell

S.I.T.C. of Production PC i7 process RAM 32 GB 2TB SSD memory with HD outputs as required, , with 16GB graphic card ,to be supplied with 27" Monitor MAKE/BRAND: Asus/HP/Dell

S.I.T.C. of Long distance transmitter for High resolution signals, Transmits HDMI, USB data, control, and analog audio up to 330' (100 m) over a shielded CAT 6A cable Supports computer and video resolutions up to 4K/60 @ 4:4:4, USB 2.0 extension, Analog stereo audio embedding, HDCP 2.3 compliant, Supported HDMI 2.0b specification features include data rates up to 18 Gbps, HDR, Deep Color up to 12‑bit, 3D, and HD lossless audio formats MAKE/BRAND: Extron DTP3 T 301 Or Equivalent in Lightware / Crestron

Supports computer and video resolutions up to 4K/60 @ 4:4:4, USB 2.0 extension, Analog stereo audio embedding, HDCP 2.3 compliant, Supported HDMI 2.0b specification features include data rates up to 18 Gbps, HDR, Deep Color up to 12‑bit, 3D, and HD lossless audio formats MAKE/BRAND: Extron DTP3 R 301 Or Equivalent in Lightware / Crestron

SITC of 4k enabled HDMI male to male cables, of 2 mtrs, Ultra-flexible HDMI cables Conforms to Premium High Speed HDMI cable performance standards 4K/60 verified MAKE/BRAND: Extron, HDMI Ultra/6 or Equivalent in Crestron / Lightware / Sony

SITC of 30 mtr / 100ft High speed 4k HDMI cable, HDMI Premium High Speed Optical Cables - Plenum, Conforms to Premium High Speed HDMI Cable performance standardsFlexible, ultra-thin 0.16” (4 mm) diameter cable Plenum, NEC CMP‑rated cable No external power is needed, Highly resistant to EMI/RFI interference, Color-coded and labeled ends MAKE/BRAND: Extron HD Pro P/100 or Equivalent in Crestron / Lightware / Sony

SITC of Light 851:it's wattage 30w-40W POWER module LED 3000k upper square frame in single piece made of die cast aluminum using pressure die-casting process,with a decorative element which is also made of die cast aluminium using pressure die-casting process, fixed on the top. Auxiliary and optical compartment can be accessed by tilting the top frame.Bottom frame with Company /brand name engraved in the mold, in single piece, made of die cast aluminum using pressure die-casting process with a four-armed bracket with flange, which is also made of die cast aluminum using pressure die-casting process, fixed at the bottom. Frosted Screen made of polymethylmethacrylate (PMMA) molded in a single piece using Injection molding process. Screen's Impact resistance: IK06. Pure polyester powder coating in Standard Grey Colour. IP Rating - IP 66. Power LED Module with Company /brand name printed on PCB with the metal core plate.LED Chips of CREE/NICHIA/OSRAM/LUMILEDS make - same should be supported by LED manufacturer's tech sheet . Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA/PC . LED Lifetime >1,00,000hours@Ts 85°C. LM80 report from LED Manufacturer should be submitted.The Light fixture shall be in compliance with IEC 60598-2-3; IEC 60598-1(Supporting Test Report from UL/UL Authorised/Intertek Laboratory should be submitted) .LM79 report also should be submitted from UL/UL Authorised/Intertek Laboratory.Sample should be submitted for approval from concerned engineer-in charge. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of 3M HEIGHT ARCHITECTURAL POST TOP POLE 3M height Pole made of complete cast iron decorative components where the internal fabricated pole of 3M is made in combination of mild steel pipe sections of suitable size covered on the outside by decorative cast iron base and columns.Decorative Cast iron Base in the cast iron mould, height again followed by a ring dia 210mm and gradual tapering upto a dia 92mm as approved by the econerned Engineer the total height of decorative cast iron base is 700mm and weight-32kgs. Decorative cast iron base should be provided with a flush door of length 228mm, width 124mm and height 30mm. Decorative cast iron flower starting with a dia 102 mm increasing gradually to 160mm and then tapering to a dia 99mm.Total height of cast iron flower is 304 mm & weight is 6.3kgs.. Decorative cast iron column(2nos.) is of 80mm dia. and having continuous grooves along the height. The height of each pillar is 750mm & weight of each pillar is 9.5kgs. Decorative Cast iron top starting with dia 80mm and a ring of dia 96mm at height of 160mm then gradually increasing to dia 120mm the top half of the decorative top should have grooves along the length, total height of cast iron top is 334mm - weight-5.2kg. All cast iron parts weight mentioned are with +/5% tolerance.Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. The pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of Projector Light, NPL-3-12, 25-35W, LED, 3000k, IP 66 NPL-3-12: The housing in light weight, made of high strength die cast aluminium and coated by static powder making it weather resistant.Protection screen in clear tempered glass with high impact resistance . High precision dial ensures precision angle adjustment.Premium thermal management by high heat conductivity aluminum alloy and thermal fins. Pure Polyester powder coating in Standard Grey Colour. Precise structure and multi-protection silicon rubber seal guarantees the fixture IP66 rated. Power LED Module with high efficacy LED's, on Printed Circuit Board with metal core plate. Electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Lens made of PC which should offer various beam angles. Estimated LED Lifetime is L70-50,000 hours minimum.LM80 report from LED Manufacturer should be submitted. Safety test report as per IS10322 from UL/Intertek lab should be submitted. BIS Certificate with manufacturer name same as brand proposed should be submitted. Minimum Light fixture Lumen output is 240Lumens. Sample Should be submitted for concerned engineer incharge for approval of light fixture. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of Spot Light, NSL-10S , LED,9-11W,LED, 3000k,IP 66 Body made of Aluminium and finished with pure polyester powder coating in grey colour. Screen in flat tempered glass. Dimension-65mm(Dia.) minimumx220mm(L) minimum,Weight-0.7kgs minimum. Electronic Driver which offers Protection against Short Circuit, Over- Voltage & Over- Current, IP 66 protection,voltage input AC240V. Estimated Lifetime-L70 @ 50,000hours minimum. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of NCL-02S-Ceiling Light, 10-15W, LED, 3000k, IP 65 Body made of aluminium & screen in tempered glass (IK 08). Pure Polyester powder coating in RAL 9005 Matt. Electronic Driver which offers Protection against Short Circuit, Over- Voltage & Over- Current. Dimension-126mm (Dia.) x 138mm(H), Weight-1.2kg. Estimated Lifetime-L70 @ 50,000 hours minimum. LM80 report from LED Manufacturer should be submitted. Sample should be submitted for approval from concerned engineer-in charge. Sample should be submitted for approval from from Architect/ engineer-in-charge. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of Projector Light, NPL-3-24, 55-65W, LED, 3000k, IP 66 - 4NOS. NPL-3-54: The housing in light weight, made of high strength die cast aluminium and coated by static powder making it weather resistant.Protection screen in clear tempered glass with high impact resistance . High precision dial ensures precision angle adjustment.Premium thermal management by high heat conductivity aluminum alloy and thermal fins. Pure Polyester powder coating in Standard Grey Colour. Precise structure and multi-protection silicon rubber seal guarantees the fixture IP66 rated. Height – 147mm, Dia.-224mm, Weight - 3.5Kgs. Power LED Module with high efficacy LED's, on Printed Circuit Board with metal core plate. Electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Lens made of PC which should offer various beam angles.Estimated LED Lifetime is L70-50,000 hours minimum.LM80 report from LED Manufacturer should be submitted. Safety test report as per IS10322 from UL/Intertek lab should be submitted. BIS Certificate with manufacturer name same as brand proposed should be submitted. Minimum Light fixture Lumen output is 4800Lumens @ full power. Sample Should be submitted for concerned engineer incharge for approval of light fixture. MAKE/BRAND: Neri / Philips / Bajaj / havells S.I.T.C. of 6M HEIGHT ARCHITECTURAL POLE WITH 4NOS OF PROJECTOR LIGHTS 6M Height pole made in combination of mild steel pipe sections 114mm dia., & 89mm dia. .Pole should have suitable provision to fix 4nos. of projector light. Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole should be shot blasted for the effective adhesion of 3layer coating so as to avoid the corrosion. The pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The pole to be mounted on a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint.Approved Makes- NERI/DW Windsor/Ghm

S.I.T.C. of Projector Light, NPL-3-24, 55-65W, LED, 3000k, IP 66 - 6NOS. NPL-3-54: The housing in light weight, made of high strength die cast aluminium and coated by static powder making it weather resistant.Protection screen in clear tempered glass with high impact resistance . High precision dial ensures precision angle adjustment.Premium thermal management by high heat conductivity aluminum alloy and thermal fins. Pure Polyester powder coating in Standard Grey Colour. Precise structure and multi-protection silicon rubber seal guarantees the fixture IP66 rated. Height – 147mm, Dia.-224mm, Weight - 3.5Kgs. Power LED Module with high efficacy LED's, on Printed Circuit Board with metal core plate. Electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Lens made of PC which should offer various beam angles.Estimated LED Lifetime is L70-50,000 hours minimum.LM80 report from LED Manufacturer should be submitted. Safety test report as per IS10322 from UL/Intertek lab should be submitted. BIS Certificate with manufacturer name same as brand proposed should be submitted. Minimum Light fixture Lumen output is 4800Lumens @ full power. Sample Should be submitted for concerned engineer incharge for approval of light fixture. MAKE/BRAND: Neri / Philips / Bajaj / havellsS.I.T.C. of 6M HEIGHT ARCHITECTURAL POLE WITH 6NOS OF PROJECTOR LIGHTS 6M Height pole made in combination of mild steel pipe sections 114mm dia., & 89mm dia. .Pole should have suitable provision to fix 6nos. of projector light. Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole should be shot blasted for the effective adhesion of 3layer coating so as to avoid the corrosion. The pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The pole to be mounted on a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU pain S.I.T.C. of Projector Light, NPL-3-24, 55-65W, LED, 3000k, IP 66 - 3NOS.

S.I.T.C. of Projector Light, NPL-3-24, 55-65W, LED, 3000k, IP 66 - 3NOS.NPL-3-54: The housing in light weight, made of high strength die cast aluminium and coated by static powder making it weather resistant.Protection screen in clear tempered glass with high impact resistance . High precision dial ensures precision angle adjustment.Premium thermal management by high heat conductivity aluminum alloy and thermal fins. Pure Polyester powder coating in Standard Grey Colour. Precise structure and multi-protection silicon rubber seal guarantees the fixture IP66 rated. Height – 147mm, Dia.-224mm, Weight - 3.5Kgs. Power LED Module with high efficacy LED's, on Printed Circuit Board with metal core plate. Electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Lens made of PC which should offer various beam angles.Estimated LED Lifetime is L70-50,000 hours minimum.LM80 report from LED Manufacturer should be submitted. Safety test report as per IS10322 from UL/Intertek lab should be submitted. BIS Certificate with manufacturer name same as brand proposed should be submitted. Minimum Light fixture Lumen output is 4800Lumens @ full power. Sample Should be submitted for concerned engineer incharge for approval of light fixture.MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of Linear Wall Washer,NWWL-7-24,20-30W, LED, 3000k, IP 66NWWL-7-24: The housing in light weight, made of high strength aluminium and coated by static powder making it weather resistant.Protection screen in tempered glass with high impact resistance . Pure Polyester powder coating in Standard Grey Colour. Precise structure and multi-protection silicon rubber seal guarantees the fixture IP66 rated. Length-1000mm,Height – 30mm, Width.-38mm, Weight - 1.5Kgs.Power LED Module with high efficacy LED's, on Printed Circuit Board with metal core plate. Common external electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Lens made of PC which should offer various beam angles.Estimated LED Lifetime is L70-50,000 hours minimumLM80 report from LED Manufacturer should be submitted. Safety test report as per IS10322 from UL/Intertek lab should be submitted. BIS Certificate with manufacturer name same as brand proposed should be submitted. Minimum Light fixture Lumen output is 1800Lumens Sample Should be submitted for concerned engineer incharge for approval of light fixture.MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of MELIA-ILLUMINATED BOLLARD-10W-15W,LED, 3000K The Bollard suitable for on ground installation,It is made in combination of Steel pipe of 127mm dia. & decorative cast iron elements. . After Fabrication, Entire bollard should be shot blasted for the effective adhesion of 3layer coating so as to avoid the corrosion.Decorative base with company name/logo engraved - it's design starting with 178mm dia. continues for a height of 30mm,than gradually tapering to 150mm,for a height of 60mm, ends. with ring of 165dia. and 20mm height. total height of the base is 140 mm & Weight is 3Kgs. and top sphere shaped decorative element design starting with a ring of 150mm dia. and 18mm height,followed by a section of 130mm dia,then gradually tapering to 70mm dia. for a height 17mm,followed by a ring of 87mm dia.,17mm height and ends with a sphere section of 125m dia. total height is 170mm - Weight is 3Kgs.All cast iron parts weight mentioned are with +/- 5% tolerance. LED source is made of Silicon material-Much more flexible,Efficient heat dissipation,Perfect resealing with silicone glue. Mounting channel made of aluminium. Diffused Screen in Acrylic, LED-source Efficacy>90lm/W,SMD LED,yellow glue 3M,120 degree beam angle, Voltage DC 24V. It also includes Externl common Electronic Power Supply(Meanwell /Equivalent) ,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection.FInish- Pure Polyester Powder Coating in customised colour Metallaic Grey. IP Rating - IP 54. Height – 1000mm, Dia - 127mm. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of Underwater Spot Light, NHL-145, LED, 8-10W, LED, 3000k, IP 68,External common power supply NHL-145: The housing in circular shape is completely made of high strength stainless steel(304grade minimum). Protection screen in clear tempered glass with high impact resistance . Precise structure and multi-protection silicon rubber seal ensures the Ingress Protection-IP 68. Dimension-Dia.-145mm,Height – 180mm, Weight - 1.2Kgs.Power LED Module with high efficacy LED's(Cree/Osram/Nichia/Lumileds), on Printed Circuit Board with metal core plate. Common external electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Lens made of PC which should offer various beam angles. Estimated LED Lifetime is L70-50,000 hours minimum.LM80 report from LED Manufacturer should be submitted. Minimum Light fixture Lumen output is 700Lumens. Sample Should be submitted for concerned engineer incharge for approval of light fixture. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of NGB-6-1-Ground Buried Uplight, 1-2W, LED, 3000k, IP 67 Body made of Die cast aluminium using pressure die casting process. Top Cover in Stainless steel & screen in tempered glass (IK 08). Burying barrel in ABS.External Electronic Driver which offers Protection against Short Circuit, Over- Voltage & Over- Current. Dimension-35 (Dia.) x38mm(H), Weight-0.1kg. Estimated Lifetime-L70 @ 50,000 hours minimum. LM80 report from LED Manufacturer should be submitted. Sample should be submitted for approval from concerned engineer-in charge. Sample should be submitted for approval from from Architect/ engineer-in-charge. MAKE/BRAND: Neri / Philips / Bajaj / havells S.I.T.C. of NSL-5-5 -Wall Recessed Light, 4-6W,LED,3000k, IP 65

S.I.T.C. of NSL-5-5-wall resessed light , 4-6W, LED, 3000k, IP 65 Body-Die-casting aluminium Body with screen in tempered glass.Body colour-RAL 9005 Matt ,Dimension-162mm(L)x96mm(H)x65mm(D),Weight-0.55kg. Electronic Driver which offers Protection against Short Circuit, Over- Voltage & Over- Current, IP 65 protection,CRI > 70,voltage input AC240V.Estimated Lifetime-L70 @ 50,000hours minimum.Sample should be submitted for engineer incharge Approval. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of Projector Light, NPL-3-12, 25-35W, LED, 3000k, IP 66 NPL-3-12: The housing in light weight, made of high strength die cast aluminium and coated by static powder making it weather resistant.Protection screen in clear tempered glass with high impact resistance . High precision dial ensures precision angle adjustment.Premium thermal management by high heat conductivity aluminum alloy and thermal fins. Pure Polyester powder coating in Standard Grey Colour. Precise structure and multi-protection silicon rubber seal guarantees the fixture IP66 rated. Power LED Module with high efficacy LED's, on Printed Circuit Board with metal core plate. Electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Lens made of PC which should offer various beam angles. Estimated LED Lifetime is L70-50,000 hours minimum.LM80 report from LED Manufacturer should be submitted. Safety test report as per IS10322 from UL/Intertek lab should be submitted. BIS Certificate with manufacturer name same as brand proposed should be submitted. Minimum Light fixture Lumen output is 240Lumens. Sample Should be submitted for concerned engineer incharge for approval of light fixture. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of Compound Light, NCL-200S, LED, 10-15W, LED Lamp(E27), 3000k & It's mounting Bracket NCL-200S: The housing in cubical shape is completely made of Acrylic(PMMA). Minium Dimensions-L-200mm,W– 200mm & H-200mm.Light source is made of high efficacy LED Lamp(E27 Base) .Light Fixture Sample should be submitted for approval from concerned engineer-in charge.Mounting Bracket - Bracket made of steel pipe section 60mm dia. Entire bracket shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire bracket is hot dip galvanized(60 microns Minimum ) for the effective corrosion resistance . The bracket to be provided with a suitable size steel plate. This mounting steel plate along with anchor fasteners of suitable size to be used for ensuring firm grouting into the existing concrete pillar. Bracket & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of Wall DownLight, 12W, LED, 3000k, IP 65 Body-Die-casting and Extruded aluminium & screen in temepered glass.Body colour-RAL 9005 Matt , Electronic Driver which offers Protection against Short Circuit, Over- Voltage & Over- Current, IP 65 protection,CRI > 70,voltage input AC100-240V. Dimension-110mm(Dia.)x175mm(H),Weight-1kg. Estimated Lifetime-L70 @ 50,000hours minimum.Safety test report as per IS10322 from 3rd party lab should be submitted. BIS Certificate with manufacturer name same as brand proposed should be submitted.. Sample should be submitted for approval from concerned engineer-in charge. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of ,Pixel Dot Lights. NPXL-50-3000k,2W-3W, LED Make : EPISTAR / CREE / OSRAM / SEOUL, Completely enclosed in transparent optical grade PVC material, UV resistant grade : Class 4, Fire retardant grade : V-0, Mean rated service life L70 (tq 25 °C) = 50,000 hours, Pixel Module Wattage : 2W-3W, Input Voltage : DC12V/DC24V, Light Angle : 120-180°, Electrical Grade : Class III, Protection Grade : IP67, It also includes the 150W,Constant Voltage(DC12/24V) driver-metal body, required-Inventronics/Equivalent. Approve. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of 1Universe (512Channels) DMX controller with following features & specifications:This is built on the latest generation of lighting controllers and combines all recent innovations. Designed for DIN rail mounting, this is the perfect solution for midrange lighting installations. Delivered with 512 DMX channels.The lighting levels, color and effects can be programmed from a PC, Mac, Android, iPad or iPhone using software from our website.It's Key Features includes • DMX Stand Alone controller • Up to DMX512 universes (512channels) • RDM compatible • USB & Ethernet connectivity for programming/ control • Stand Alone mode with 99 scenes • Play scenes in 5 areas / zones • microSD slot • 8+3 dry contact trigger ports • Test scenes rotary switch • Windows/Mac software to set dynamic colors/effects • iPhone/iPad/Android remote and programming apps • cloud compatibility(optional at additional cost).Technical Data Input Power 12v DC (8-15V range), Output Protocol DMX512 , Programmability PC, Mac, Android, iOS, Connections-USB-C Ethernet Screw terminals for DMX / RDM Universes, 8+3 Contact ports, 12v power-in Battery holder (CR2032), microSD slot Memory SD Card ,Environment IP20 / to 0 to +50°C, Buttons Rotary switch ,OS Requirements Mac OS X 10.8-10.14 Windows 7/8/10 Standards CE, ETL, Low voltage, EMC, and RoHS Programming of DMX Controller. Minimum of 10 scenes need to be configured. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C .of 6port DMX Splitterwith following features & specifications:DMX signal splitter enables branching in complex DMX installations. The combination of a large number of receivers in series can be troublesome, therefore it was possible to create branching DMX tracks using a splitter.With Splitter, it possible to split the DMX input signal into 6 independent branches. The individual outputs are galvanically isolated from input and between each other. The output signals are appropriately reinforces, which guarantees correct operation of the entire installation. DMX Splitter is manufactured in a housing adapted for mounting on standard DIN 35mm rails. Specification - Power Supply-DC12-24V,DMX Channels--512,Nos. of DMX Inout-1 & output-6,Optical Isolation of DMX Lines,Built-in Terminatior,breakdown voltage of the isolation>1000V,current consumption-<500mA,Weight-0.2Kgs.,W-105mm,H-86mm&D-60mm. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C of Track mounted cylinderical spot light Ø45mm Height 142mm, 9w, 870 lm, beam angle 28° to 40 Deg. (Manual Zoom), CCT 3500K, CRI>90, SDCM (initial McAdam) ≤2, Efficacy 94lm/W, operating Voltage Range of 48V DC,Black finish, Life L80B10 @ 50000 Hrs.@ 25 Degree Ambient temp. The luminaire have UGR≤18 andingress protection of IP40. MAKE/BRAND: Neri / Philips / Bajaj / havells

S.I.T.C. of 1 Mtr. Length of 48V Track for track light with connectors (L&Tshape connectors) MAKE/BRAND: Neri / Philips / Bajaj / havells

SITC of LED strip light of 7 watt per meter 3000K IP67 operate by 24 VDC driver controlling minimum 10 meter strip with having suitable mounting bracket to fix inside the step and ghat, tree , amphi theatre seating arrangement. MAKE/BRAND: Neri / Philips / Bajaj / havells

SITC of LED RGBW DMX conrol LED channel with aluminium extrusion channel linkable option outdoor IP66 with diffuse optic power 15 watt per meter control by independent DMX controller creating multiple lighting scene (minimum 32 scene). MAKE/BRAND: Philips / Havells / Bajaj / Aura

SITC of LED screen 4 mm pitch 5500 nits IP66, size 3m x 5m floor standing mounting bracket with media server , AV conectivity , link with APP through wifi or QR code rider MAKE/BRAND: Absen / Philips / Havels / Bajaj / Aura

SITC of MEDIA server MAKE/BRAND: Absen / Philips / Havels / Bajaj / Aura

SITC Mobile app for QR code MAKE/BRAND: Tech visio / Magic brush / Mistic

SITC of Fort content and video MAKE/BRAND: Tech visio / Magic brush / Mistic / ECOWAY

SITC of entry art work of height 8000mm made up of fibre body made up of glowing fibre with base of 2500 x 1000 mm MAKE/BRAND: Cutomised by Contractor and approved by consulting team

SITC of RGB lights of 24 watt 16 nos DMX control with continuous transition made by aluminium extrustion with connecting cable & controller MAKE/BRAND: Philips / Havells / Bajaj

SITC of LED screen with 31.5 mm pitch with high brightness of 3500 NIT day visibility with media server controller MAKE/BRAND: ABSEN / Havells /Philips / Bajaj

SITC of Programme controller and present scene controller with built in memory 256 GB and ram of 16 GB to store programme. MAKE/BRAND: ABSEN / Havells /Philips / Bajaj

Set of all control cable and power cable MAKE/BRAND: ABSEN / Havells /Philips / Bajaj

SITC OF RGB laser system projection with laser power of 42 watt ( red 9w/638nm. Green 13w/525nm, blue 20w/ 455nm ). Cooling mode - lasr with TEC cooling, whote machine is with air cooling, with enclosure of IP65,power consumption 1200watt. Laser service life 10000 hoursand operating volatge 230 volt 50Hz.lighting effect- full color animation laser with high speed galvanometer scanning technology. laser projector should confirm to EU norm and CE / UL certified. (Kvant / Aura / Bajaj)

SITC of customised laser enclosure for all laser projector with IP65 protection with security mechanism ( techvisio / mapan / Aura)

SITC of pangolin software to develop various lighting show ( Pangolin / laser world / star dimension)

SITC of wiring , power cable , control cable for laser

S.I.T.C. of Smart poles of 8/ 10 mtrs heights Customized enclosure for above projector with pole mounting arragement IP65 protection and security. Each enclosure allow to put minimum 1 projector, White in color, easy maintenable Make: Techvisio/ Mapan/Aura / LM3X [Urban pole / Valmount structurs + Encloures for Barco Projectors

S.I.T.C. of 20 KVA UPS with 30 minutes power backup, along with Electrical cabling and Earthing for projector

S.I.T.C. of Long distance transmitter for High resolution signals, Transmits HDMI, USB data, control, and analog audio up to 330' (100 m) over a shielded CAT 6A cable Supports computer and video resolutions up to 4K/60 @ 4:4:4, USB 2.0 extension, Analog stereo audio embedding, HDCP 2.3 compliant, Supported HDMI 2.0b specification features include data rates up to 18 Gbps, HDR, Deep Color up to 12‑bit, 3D, and HD lossless audio formats MAKE/BRAND: Extron DTP3 T 301 Or Equivalent in Lightware / Crestron

S.I.T.C. of Long distance Receiver for High resolution signals, Receives HDMI, USB data, control, and analog audio up to 330' (100 m) over a shielded CAT 6A cable Supports computer and video resolutions up to 4K/60 @ 4:4:4, USB 2.0 extension, Analog stereo audio embedding, HDCP 2.3 compliant, Supported HDMI 2.0b specification features include data rates up to 18 Gbps, HDR, Deep Color up to 12‑bit, 3D, and HD lossless audio formats MAKE/BRAND: Extron DTP3 R 301 Or Equivalent in Lightware / Crestron

SITC of 30 mtr / 100ft High speed 4k HDMI cable, HDMI Premium High Speed Optical Cables - Plenum, Conforms to Premium High Speed HDMI Cable performance standards Flexible, ultra-thin 0.16” (4 mm) diameter cable Plenum, NEC CMP‑rated cable No external power is needed, Highly resistant to EMI/RFI interference, Color-coded and labeled ends MAKE/BRAND: Extron HD Pro P/100 or Equivalent in Crestron / Lightware / Sony

Content with Script writing: includes movement, actions, expression and dialogue of the characters, drama Storyboard, Storytelling, 2D 3D animation, Graphics, Art Works, Archival Imagery, Video-timeline, SFx, VFx, Voiceovers and Music etc for the show.etc for about 10 mins to 15 Min. MAKE/BRAND: Main Projection mapping show, -270 deg.

Content Script writing: includes movement, actions, expression and dialogue of the characters, drama Audio Visual Content: includes visual Storyboard, Storytelling, 2D 3D animation, Graphics, Art Works, Archival Imagery, Video-timeline, SFx, VFx, Voiceovers and Music etc for the show.etc for about 5 to 10 mins.

Content Script writing: includes movement, actions, expression and dialogue of the characters, drama Audio Visual Content: includes visual Storyboard, Storytelling, 2D 3D animation, Graphics, Art Works, Archival Imagery, Video-timeline, SFx, VFx, Voiceovers and Music etc for the show.etc for about 3 to 5 mins.

SITC of ISO 7240‑16 Certified EVAC PA controller capable of adding 12 zones in the system and expandable upto 400 zones with 14x 4 Audio matrix with full DSP functionality. 8 audio, inputs, 4 audio outputs, 4 channel output matrix. Shall support the following: single line, switching or redundant group A/B switching, amplifier redundany, 4 x 100V audio inputs, and 12 speaker line outputs. Fault, warning and event conditions log. Built in message, manager for 100 emergency/business calls up to 85 minutes. 18 control inputs and 18, control outputs. Impedance measurement and Pilot Tone supervision for speaker line, monitoring. The network controllers shall have a possibility to be integrated using an, interface module which is able to send and receive Audio to and from other, Controllers.Frequency response (ref. 1 kHz) 20 Hz to 20 kHz (-0.5 dB), Signal-to-noise ratio, (A-weighted): Line in to line out: 106 dB typical, THD+N < 0.05%, Crosstalk (line level) Line, in to line out (0 dB gain): < 100 dB at 1 kHz, Sample rate 48 kHz, DSP processing resolution, 24-bit linear A/D and D/A conversion, 48-bit processing. Graphics User Interface software, should be considered for Monitoring and control of signal. MAKE/BRAND: Bosch

SITC of EN54-24 Certified IP65 rated outdoor surface mount speaker to be supplied with standard U-bracket, Maximum power22.5 W, Power tapping15/7.5/3.75/1.9 W, Sound pressure levelat rated power / 1 W(1 kHz, 1 m)98/86 dB (SPL), Opening angleat 1 kHz / 4 kHz(-6 dB)179° / 101° (hor.)168° / 35° (ver.) MAKE/BRAND: Bosch

SITC of EN54 Certified EVAC Router for adding 24 zones in the system and to route 4 channels into, 8 100V audio inputs to 24 loudspeaker line outputs. 2-in-6 matrix. 20 Control Inputs, 26, Control Outputs. Shall support single line switching or redundant group A/B switching, amplifier redundancy. Impedance measurement and Pilot Tone supervision for speaker line monitoring MAKE/BRAND: Bosch

SITC of 480 W power amplifier in a 3U high housing with 70 V / 100 V and 8 ohm outputs,Dual inputs with priority switching,100 V input for slave operation on 100 V speaker line,Mains, battery back-up, With Following Features: 1.Output power (rms) 480 W 2.Frequency response 60 Hz to 18 kHz (+1 / -3 dB at -10 dB ref. rated output) 3.Distortion <1% @ rated output power, 1 kHz 4.S/N (flat at max volume) >90 dB 5.Battery power supply:24 VDC. MAKE/BRAND: Bosch

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 300 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 185 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 120 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 70 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 35 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, installing, testing and commissioning FR, XLPE armoured cable 4 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

SITC L.T. Feedar Pillar 4 Way (As per MSEDCL Specification)

SITC L.T. Feedar Pillar 6 Way (As per MSEDCL Specification)

Supplying & laying (including excavation) reinforced cement concrete pipe of IS 458:2003 NP-2 class of 150 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc.complete

Supplying & laying (including excavation) half round reinforced cement concrete pipe of IS 458:2003 NP-2 class of 150 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete

Providing C.C. foundation for LT Feeder Pillar

Supplying and erecting pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. strip complete with all materials as per specification no. EA-EP

Providing earthing with Galvanised cast iron earth plate size60 x 60 x 0.6 cm complete with all materials, testing & recordingthe results as per specification No. EA-EP

Supplying and erecting Rolled steel Joist (Girder) pole 116 x 100, 9 m long pole with provided base plate in provided foundation as per specification No. OH-PL/RSJ

Supplying & erecting MS pole bracket for guarding/LT OH line, fabricated from angle iron 50x50x6mm and 550mm long for necessary nos. of provided insulators, and erecting on pole with 50x6mm clamp complete as per specification no. OH-PL/BKT

Supplying and erecting porcelain shackle type LT medium insulator 75x115mm dia. with G.l. (shackle) strips, nuts and bolts, complete.

Providing cement concrete for foundation or for concrete filling in 1:3:6 ratio with 20 to 25 mm. stone metal duly plastered with necessary curing for pole muffing or any other purposes

Dismantaling of MSEDCL HT/LT Pole with line and submitted to MSEDCL store

Supplying , erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) cable 22 kV(E), 3 x 300 sq. mm. aluminium conductor laid in provided trench / pipe as per specification no. CB-HT

Supplying , erecting & terminating XLPE insulated galvanised steel formed wire armoured (strip) cable 22 kV(E), 3 x 95 sq. mm. aluminium conductor laid in provided trench / pipe as per specification no. CB-HT

SITC of motorized, SCADA compatible 22 KV, SF6 outdoor type 2 Isolator + 0 Breaker

SITC of motorized, SCADA compatible 22 KV, SF6 outdoor type 2 Isolator + 1 Breaker

SITC of motorized, SCADA compatible 22 KV, SF6 outdoor type 2 Isolator + 2 Breaker

Providing and erecting Heat shrinkable straight through joint kit for 11 kV (UE)/22 kV ( E ) XLPE HT cable 3x240 to 300 sq. mm. with necessary material as per specification no. CB-JT/HT

Providing and erecting 22 kV Heat shrink touch proof termination kit (A1) kit for XLPE 3Cx300 sq.mm.

Providing and erecting 22 kV Heat shrink touch proof termination kit (A1) kit for XLPE 3Cx95 sq.mm.

Providing C.C. foundation for Ring main Unit (RMU) with necessary steps for operating of RMU as per direction of MSEDCL

Shifting and Re-erecting of DTC including c.c. foundation , earthing and fencing for transformer

Providing & Laying of sand as directed by MSEDCL

Dismantling of MSEDCL HT/LT Pole with line, Four pole structure and submitted to MSEDCL store

Supplying, erecting, testing, commissioning 22 KV HT metering cubical (compact type) approved by MSEDCL/licensee fabricated with 2mm.(14 SWG) M.S. sheets with supporting angle and channel, painted with powder coating / epoxy paint of required shade copper bus bar size 25x6 mm electronic security lock and heavy duty mechanical lock, with counter meter for measuring no of times the opening of doors, top side cover ( CT,PT cover) interlock with meter doors, epoxy coated 3 nos CT having required ratio between 50/5 A to 100/5 A, VA10, class 0.2S, 22000/V3/110/V3 VA 50,class 0.2 epoxy terminal block suitable for provided trivector meter, and provision for incoming and outgoing cables etc. complete duly tested by licensee with necessary test certificates and erected on provided plinth/ cc foundation

Providing & erecting 9 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Providing & erecting 5 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 155 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole).

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 9m to 10m high octagonal /conical GI pole).

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 9m to 10m high octagonal /conical GI pole).

Supply and erection of BREEZA type decorative hot dip Galvanized single arm bracket of 1.5 Meter long made from 48.3 mm OD pipe, min 3 mm thick with cross support of 33.7 mm OD pipe, min3 mm thick with cap pipe length of 0.450 Meter suitable for Oct pole with top of 70 mm, with 4 Nos bolts. The Bracket shall be capped with suitable decorative STEEL/FRP ball duly bolted/ welded. The tilt angle shall be 10 to 12 degree as directed by Engineer - in - charge. BREEZA type bracket or its equivalent as per the drawings enclosed.

Supply and erection of BREEZA type decorative hot dip Galvanized double arm bracket of 1.5 Meter long made from 48.3 mm OD pipe, min 3 mm thick with cross support of 33.7 mm OD pipe, min3 mm thick with cap pipe length of 0.450 Meter suitable for Oct pole with top of 70 mm, with 4 Nos bolts. The Bracket shall be capped with suitable decorative STEEL/FRP ball duly bolted/ welded. The tilt angle shall be 10 to 12 degree as directed by Engineer - in - charge. BREEZA type bracket or its equivalent as per the drawings enclosed.

Supply Installation Testing & commissioning of Integral high pressure Die cast/extruded aluminum LED Streetlight luminary the system wattage (fixture's total power consumption)should be 150W +/- 5 Watt Details as per technical specification attached.

Supply Installation Testing & commissioning of Integral high pressure Die cast/extruded aluminum LED Streetlight luminary the system wattage (fixture's total power consumption)should be 90W +/- 5 Watt Details as per technical specification attached.

Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and laying (including excavation) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Providing M20 concrete for resurfacing the road.

Supplying, erecting & marking SPMCB 0.5A to 5A, C-series with rated short -circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

SITC of street light control panel inclusive of all electrical accessories mentioned in tender document

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 50 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

1. CIVIL MAINTENANCE WORK Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases(NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram/15 l). plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist.

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete.prior approval of Superintending Engineer will be necessary

Supply & Fixing of Rock / Stone Finished outdoor vitrified flooring Tiles 16 mm thick and required width wide in plain pattern including Cement float, filling joints, with neat cement slurry, Natural sand, curing and cleaning complete. with prior approval of concerned Superitending Engineer.

Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm to 8 to 10mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete.

Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb without gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant

Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb with gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete.

Providing and Supplying SAFETY RUBBER FLOORING SYSTEM Including Material, labours lead etc. complete after approval of Engineer in Charge

Providing and laying Natural unpolished Black/Brown Pebbles of size 30mm to 50mm

Providing and Supplying Sea sand Spec. No.: As directed by Engineer-In-Charge.

Providing and applying first coat of approved Waterproof primer, and two coats of waterproof acrylic based textured exterior paint of an approved make and colour as per manufacturers specifications to textured sand faced or other surfaces, upto 10m height from ground level and at all locations as directed including preparing surfaces for painting by any approved means, scaffolding, cleaning and curing etc. complete as directed by Engineer-in-charge

Providing and applying one coat of approved silicate based primer with roller / brush and one coat of granite textured exterior paint of an approved make with spray to get designed finish with two coats of lacquer in approved finish shade of thickness 2-2.5mm as per approved manufacturers specifications to textured sand faced or other surfaces, at all heights and locations as directed including preparing surfaces for painting by any approved means, watering, scaffolding, cleaning and curing etc. complete as directed by Engineer-in-charge

Wall Painting art work : Designing, Conceptualization & painting of 3D artistic on any surface at all height and location as directed. The paint should be used for the artistic painting is high quality acrylic paint. painting should be coated with weather proof warnish.

Heritage Look Plaster :- Provided heritage look plaster over provided plaster surface finishing with rustic textured material of 10 to 12 mm thick including preparing the surface in various aspect like arche, sacfolding and curing etc complete as directed by Engineer-In-Charge

Providing vee pointing with cement mortar 1:3 for stone / Brick masonry including scaffolding and curing etc. complete

2. GARDEN / LANDSCAPE / HOTRICULTURE MAINTENANCE WORK Maintenance of Existing & Newly Developed Gardens: For 7th to 12th Month

For 2nd Year Maintenance

For 3rd Year Maintenance

For 4th Year Maintenance

For 5th Year Maintenance

3. ELECTRICAL OPERATIONAL & MAINTENANCE WORK Second Year Comprehensive maintenance of all Electrical works of 2.5% (Maintenace For Approach Road & Pedestrian Street Light , Wire , Cables Etc Shall Not Be Considered For Maintenance Purpose)

Third Year Comprehensive maintenance of all Electrical works of 4% (Maintenace For Approach Road & Pedestrian Street Light , Wire , Cables Etc Shall Not Be Considered For Maintenance Purpose)

Fourth Year Comprehensive maintenance of all Electrical works of 5.5% (Maintenace For Approach Road & Pedestrian Street Light , Wire , Cables Etc Shall Not Be Considered For Maintenance Purpose)

Fifth Year Comprehensive maintenance of all Electrical works of 7% (Maintenace For Approach Road & Pedestrian Street Light , Wire , Cables Etc Shall Not Be Considered For Maintenance Purpose)

Operational Cost for Next 5 years for Public Art Light Show

R AND B INFRA PROJECT PRIVATE LIMITED