Repair maintenance and miscellaneous civil works at Staff Qtrs Angarh Mirzapur OA under BA Varanasi

Amount

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

a) 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,

(i)Single socketed pipes.

a) 110 mm diameter

b)75 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

a) Single tee without door

i) 75x75x75 mm

ii) 110x110x110 mm

b) Bend 87.5°

i) 75 mm bend

ii) 110 mm bend

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-charge.

a) With cement mortar 1:4 (1 cement : 4 fine sand).

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

a) 10 litre capacity - White

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

a) Flexible pipe

(i) 32 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall

a) 20 mm nominal outer dia. Pipes.

b) 25 mm nominal outer dia .Pipes.

c) 40 mm nominal outer dia. Pipes.

Providing and fixing uplasticised PVC connection pipe with brass unions :

a) 45 cm length

(i) 15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT bib cock of approved quality and colour.

a) 15mm nominal bore, 86 mm long. Weighing not less than 88 gms.

Providing and fixing PTMT stop cock of approved quality and colour.

a) 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.

a) 20 mm nominal bore, 120 mm long. Weighing not less than 198 gms.

Providing manual assistance for plumbing work, carpentary work, which are not covered above and are not possible to measure.

Trimming/Cutting of trees branches of the girth including cutting of trunks and branches which are covering and pose threat to euipments lying underneath the towers and TE Building with all safety measures including ropes, safety jacket, hooks by experts by using required equipments and disposal of unserviceable material.

a) Beyond 30 cm girth up to and including 60 cm girth

Applying cement slurry admixed with water proofing chemical such as tapecrete or equivalent in proportion as recommended by the manufacturer to damp portion of wall in two coats complete as per direction of engineer in charge

Providing unskilled labour for work which are not covered above and are not possible to measure

P/F C.P. brass waste Coupling for sink or wash basin as per direction of E-in-C.

a) 32 mm dia

Providing and fixing 100 mm CP jali as per direction of E-in-C

P/F PVC cover to over head PVC water storage tank i/c necessary nuts & bolts.

Repairing of Aluminium door/ window frame and shutter with required cleat screws after taking out the shutter i/c cost of labour etc. all complete as per direction of E-in-C.

Cleaning of Manhole with connecting sewer line and disposal of malva out side compound etc all complete as per direction of E-in-C.

P/F PVC Cistern flush handle/ball valve/long bend Of required colour and shape.

Deduct for crediting to the contractor old unserviceable material obtained after dismantentling,

a) PVC stop cock, bib cock, pillar cock,cistern, PVC water tanks etc.

b) C.P. brass stop cock, bib cock. Pillar cock angle cock, Gate valve etc.

c) damaged Flush door shutter

d) Hydraulic door closer

M/S DILIP KUMAR (BID ID -890121)