SPECIAL REPAIR TO BLDG NO BI-7 OF JASWANT SAINIK INSTITUTE (JSI) AND PROVISION OF ELECTRIC INCINERATOR AT COMD HQ BLDG UNDER GE (FW) KOLKATA

Amount

NOTES :(i)The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates. (ii) It is highlighted that the cretin condition of General Condition Of Contracts (IAFW-2249) has been modified as direction of MOD i.e inclusion of performance security, deletion of risk & cost provisions and increase in defects liability period all as specified in tender document. The tenderers should keep in mind while quoting their offer

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, pillars etc but excluding ashlars facing, dressed stone work and precast concrete articles complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floors and pavings n.exc 15cm thickness, (Below or above Ground level) and disposal of debris and rubbish to a distance n.exc 100m complete all as directed by the Engr-in-Charge

Demolition of reinforced cement concrete in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of 150mm bore cast iron pipes, jointed in cement mortar and taking out from trenches complete all as specified and directed.

Demolition of breaking drain pipe (salt glazed or RCC pipe) set in cement mortar for 150 mm dia & over complete all as specified and directed.

Dismantling AC Corrugated, semi corrugated sheets in roof coverings including any type of ridges and disposal of all material, complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and as directed.

Dismantling timber fillets, rails posts, rafter, purlins etc under 40Sqcm in section complete all as directed by Engineer-in-Charge.

Dismantling timber scantling 40 Sqcm and over in section in any position, unframed work complete all as directed by Engineer-in-Charge.

Dismantling boarding, any description, any type, fixed in any position with nails including cover fillets completed all as directed.

Dismantling of wall or ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs / blankets of any thickness including cover fillets complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, etc and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material exc 250m but n.exc 500m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed .

Material and labour for Brick work with sub class 'B' fly-ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Material and labour for brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in cement mortar 1:4 as in half brick thick walls complete all as specified and directed.

Supply and fixing mild steel TMT bars 6-8 mm dia , cut to length and bent to shape as required, including cranking , bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed ) not less than 0.90 mm dia complete all as specified and directed .

Material and labour for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in cills, copings, kneelers, apex stones, bed plates etc including formwork complete all specified and directed.

Supply and fixing PVC solid wall lining consisting of 5 mm thick single side prelam coloured PVC sheet inclusive of solvent cement for fixing on PVC frame as per manufacturer’s specification and instruction and as directed by the Engineer-in-Charge.

Material and labour for 5 mm thick solid PVC sheet fillet of width 50 mm at interval of 250 mm c/c fixed with 65 mm nicked cadmium plated screws @ 200 mm c/c for wall paneling inclusive of fixing on to wall to make PVC frame complete all as specified and directed.

Supplying & fixing powder coated aluminium snap grid ceiling of grid size 605mm x 605mm , made of powder coated aluminium main Tee of section 36mm x 25mm x 1.40mm, cross Tee of section 23.50mm x 23.50mm x 1.40mm thick and angle of section 25mm x 25mm x 1.40mm thick including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long for providing 4 mm thick 'E' board "Classic" , reinforced, designer series,with HPSC (high pressure stream curing) board fixed to frame complete all as specified and directed by the Engr-in-Charge. Note : Quoted rate shall deemed to include the cost of ceiling board.

Taking down chowkhats or frames not exc 1.5 sqm each (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkhats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutter from the frame) complete all as specified and directed.

Supply and fixing powder coated aluminium frame for doors, windows, ventilators (minimum thickness of powder coating 50 micron) with one or more rebates including joining cleat for fixing etc complete all as specified and directed. Note : (a) Thickness of aluminium section shall not be less than 1.5 mm. (b) Anodizing shall be 15 micron conforming to IS-1868-1996

Supply and fixing powder coated aluminium door, window and ventilator shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, 1 no mortice lock ,anodised aluminum snap beading,tower bolt ,screws etc. complete all as specified and as directed. Note : (a) Thickness of aluminium section shall not be less than 1.5 mm. (b) Anodizing shall be 15 micron conforming to IS-1868-1996 (c) Minimum thickness of powder coating 50 micron

Supply only 12 mm thick pre-laminated particle board interior grade, pre-laminated one side with decorative choice of lamination and other side balancing white lamination fixed to door shutter, partition & similar places etc. complete all as specified and directed. Note :- Fixing only rate is included in window/door shutter/frames items considered therein.

Material & labour of power coated aluminium 18 mm width, three track sliding window with shutters made of 1.5mm thick aluminium section for bottom track (1.28 kg/m min) & top , side track of shutter side vertical frame of 1.5mm thick(minmum) , shutter to be interlocking with vertical frame including necessary jointing cleats, glazing clips, rubber neoprene packing, roller, locking arrangement, handles 2 Nos , anodised aluminium snap beading screws etc. complete all as specified and as directed. Note:- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall be deem to included quoted rate. Only measure opening size of window. (ii) The drawing of window shall be approved by the GE prior to incorporation in the work. (iii) Only Glass for door shall be measure and paid separately under relevant items of BOQ . (iv) Minimum thickness of powder coating 50 micron

Supply and fixing mild steel bands, straps, supports or stays of rain water, ventilating pipes including bolts, hooks (stay) for large gates, hook and pintel hinges, clamps, hold fasts, wall ties,flat iron fillets for securing wire mesh, wind tie and similar work including necessary drilling bolting or riveting etc conforming to Fe – 290 Gde E – 165 complete all as specified and as directed.

Supply and fixing of pressed steel door frames (fabricated out of CRLCS sheet 1.6 mm thickness) 105 x 60 mm size with one or more rebates including necessary fixing lugs, hinges, lock striking plate etc. complete all as specified and as directed.

Material and labour for PCC 1:3:6 type C-1(using 20 mm graded aggregate) as in filling pressed steel door frame complete all as specified and as directed.

Supply and fixing 35 mm thick, 2nd class hardwood, factory made, Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fixing 30 mm thick, factory made, Second class hardwood, glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, etc complete all as specified and directed in SSR Part I Section 8 clause 8.24 (b).

Supply and fixing Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

Supply and fixing solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

Supply only liquid water proofing compound complete all as specified and directed. Make : Dr. Fixit LW 100, Sika, Fosroc

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as directed and specified .

Supply and fixing 3 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

All as per item no 42 here in before but 4.8 mm thick sheet glass

Cutting chases for water tubing, pinning in making good to facing where required in CM(1;3) to brick wall cutting grith n.exc. 10cm girth complete all as directed.

Supply and fixing mild steel framed work such as grills, grating etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-410-0 Gde E-250 complete all as specified and directed.

Supply and fixing second class hard wood small fittings such as brackets of any type , stopper/cleat for door or window, articles next. 200 cum each with MS butt hinges cold rolled medium weight 50 mm long complete all as specified and directed.

Supply and fixing medium weight cold rolled mild steel butt hinges 100 mm long complete all as specified and directed.

Supply only medium weight cold rolled mild steel butt hinges 50 mm long complete all as specified and directed.

Supply and fixing 100 mm long stainless steel butt hinge complete all as specified and directed.

Supply and fixing 150 mm size, Aluminium handles, cast type, anodised complete all as specified and directed.

Supply and fixing aluminium anodised tower bolt 150 mm long of extruded section complete all as specified and directed.

Supply and fixing aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clipes of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy, length of bolt of 250 mm complete all as specified and directed.

Material and labour for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

Material and labour for PCC 1:3:6 type C2 (using 40 mm graded aggregate) as in foundation filling and mass concrete, complete all as specified and as directed.

Material and labour for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in sub-base of flooring, etc and finished the surface even and rough complete all as specified and directed.

Material and labour for 100 mm thick, Cement concrete 1:2:4, type B-2 (using 40mm graded stone aggregate) as in flooring etc and finished the cement concrete surfaces even and smooth without using extra cement complete all as specified and directed.

Materal and labour for Vitrified, designed, coloured, tiles, 10 mm thick, (square/rectangular) polished, area of each tiles not exc 0.42 sqm but not exceeding 1.00 Sqm, as in floors, etc including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

All as per item No 57 here-in-before but on vertical surfaces such as in skirting ,set and jointed in neat cement slurry and pointed in coloured cement to match with the shade of the tiles over and incl. 10mm rendering in CM (1:3) complete all as specified and directed.

Material and labour for ceramic non skid coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc., laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile surface all as specified and directed.

Supply and fixing glazed ceramic colour tiles (450x300 x 7mm thick ) on dado & skirting , set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick cement plaster with rough finished in cement mortar 1:3 to received tile complete all as specified and directed.

Material and labour for machine cut kota stone slab flooring 20-25 mm thick over 15mm thick screed bed in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and as directed by the Engr-in-Charge.

All as per item No 61 here-in-before but over 10mm thick screed bed in CM (1:4) as in riser of steps,skirting,dado,riser etc complete all as specified and as directed by the Engr-in-Charge.

Material and labour for granite stone slab (of any type) 18 to 20 mm thick, machine cut ,bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15 mm thick screed bed in cement mortor 1:4 & cutting, polishing and making moulds on edges as in steps, jambs, pillars, window cills, cooking platforms, urinal partition and like complete all as specified and directed.

All as per item No 63 here-in-before but over 10 mm thick screed bed in CM (1:4) as in skirting/dado.

Material and labour for 15mm thick rendering in cement mortar (1:6) on fair faces of brickworks finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for 5 mm thick rendering in cement mortar (1:4) on ceiling surfaces finished even and fair without using extra cement complete all as specified and directed.

Material and labour for 20 mm thick rendering in two coats on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with integral water proofing compound with weight of cement in top layer as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note:- WPC shall be mesured and paid separately)

Material and labour for two coats of acrylic emulsion distemper over a coat of primer on internal plastered surfaces after preparation of surfaces complete all as specified and directed.

Material and labour for applying two coats of white wash on ceiling including preparation of new plastered surfaces complete all as specified and directed.

Material and labour for two coats of cement base paint over a coat of primer on external plastered surfaces after preparation of surfaces complete all as specified and as directed.

Material and labour for applying one coat of white wash on existing plaster surfaces of ceiling complete all as specified and directed.

Material and labour for complete removal of existing treatment from old wall surface and applying two coats of acrylic emulsion distemper over a coat of alkali resistant primer including preparation of surfaces complete all as specified and directed.

Material and labour for complete removal of existing treatment and treating with cement base paint over a coat of primer on external plastered surfaces after preparation of surfaces complete all as specified and directed.

Material and labour for preparation of new surfaces of steel or iron surfaces of any description, n.exc 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material & labour for two coats of synthetic enamel paint over a coat of pink primer on wooden surface of treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkhats etc n.exc 0.1 SQM each, including preparation of surfaces complete all as specified and directed.

Material and labour for two coats of synthetic enamel paint over a coat of pink primer on wooden surface of doors including preparation of surfaces complete all as specified and directed.

Material and labour for applying one coat of synthetic enamel paint on old steel surfaces of width or girth exceeding 10cm including preparation of surfacess complete all as specified and directed.

Material and labour for preparation of new steel surface over 10cm width and girth and applying two coats of synthetic enamel paint oveer a coat of red oxide primer complete all as specified and directed.

Material and labour for treating small articles on steel surface such as articles of builder's hardware such as door springs, hooks, knobs, fasteners, stays, locks, latches, holdfast etc., straps to roof trusses, gates and similar articles, when unconnected with other painting or when painted in a different tint with two coats of black japan paint over a coat of red oxide primer complete all as specified and directed.

Taking up or down 20 mm bore, steel tubing and connections complete all as directed.

All as per item No 80 here-in-before but 15mm bore

All as per item No 80 here-in-before but 25mm bore

Supply, laying, connection and testing, 25mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

All as per item No 83 here-in-before but 20mm bore

All as per item No 83 here-in-before but 15mm bore

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws compelte all as specified and as directed.

Supply and fixing pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges , valley gutter etc fixed with self tapping screws complete all as specified and directed.

Supply and fixing rolled mild steel sections as in roof truss (framed), main and cross beams, hip and jack fafters; purlins where connecteed to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed.

Supply and fixing in repair 25mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

All as per item No 89 here-in-before but 20mm bore

Supply and fixing in repair 15 mm bore pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

Supply and fixing in repair 15 mm bore bib taps, cast copper alloy fancy type chromium plated with capstan head screwed down , screwed for iron pipe of 15 mm bore and fixed , complete all as specified and directed

Supply and fixing in repair 15 mm bore stop valves cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm bore complete all as specified and directed.

Supply and fixing 25 mm dia Ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe mini weight 142 grams complete all as specified and directed.

Supply and fixing 1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top), multilayer ,hoisted and fixed in position including taking down old unserviceable one as specified in SSR Part I and directed.

Supply and fixing in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

Supply and fixing in repair 600mm long brass chromium plated 20mm dia 'D' type towel rail complete all as specified and as directed.

Supply and fixing in repair10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and directed.

Supply and fixing in repairs vitreous china (coloured) wash down water closet pan (pedestal pattern) with 'P' or 'S' trap front or back inlet, fixing bolts(except flushing cistern and flush pipe) incl plastic water closet seat cover (coloured) and mild steel chromium plated or aluminium hinging device complete all as specified and directed by Engr-in-Charge.

Supply and fixing of vitreous china wash basin white flat back, size 550 x 400 mm including CP waste coupling, 32mm bore of discharge pipe(LDPE) , GI pipe brackets and rag bolt in cement concrete/brick wall and including taking down existing HWB and making good wall surface complete all as specified and as directed.

Material & labour for forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade A complete all as specified and as directed.

Supply and laying reinforced concrete pipes, class NP2 of 150mm dia laid in trenches and jointed with collars complete all as specified and as directed.

Material and labour for providing pre-cast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in cover slab of manholes, septic tank, soak well etc set in cement mortar 1:4 with plain fair faces including chamfered weathering, throating etc including necessary use and waste of form work complete all specified and directed. (Note : Reinforcement shall be measured and paid separately)

Material and labour for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in surface channel and drain complete all specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

Add or deduct for each 25 mm girth or part thereof over or under 30cm complete all as specified and directed.

Material and labour for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

Material and labour for concrete bed to drain pipes of cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) including packing under and hunching against the side of pipe after they are laid and tested complete all specified and directed.

Material and labour for cutting holes into existing manholes / brick wall for connecting new drains / pipe, making good to pipes and rendering, cutting out existing benching for and forming branch channel (1/2 round 3/4 section) in cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) finished smooth for 150 mm internal dia of pipe complete all as specified and directed .

Supply and fixing 150 mm bore cast iron (Spun) waste and vent pipes centrifugally cast , in any length with or without ears, with cement joints, fixed to walls complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 111 here in above but 100 mm bore complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 111 here in above but laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge. Note : Earthwork shall be measured and paid separately under respective item.

Supply and fixing 150 mm bore cast iron (Spun) bends (any radius), diminishing pieces or tapers (larger bore to be measured) complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 100 mm bore cast iron (sand cast) branch pieces, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 100 mm bore cast iron (sand cast) bends (any radius), diminishing pieces or tapers (larger bore to be measured) complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 100 mm dia CI vent cowl complete all as specified and as directed.

Supply and fixing of 100 mm cast iron sanitary connection socket to fit WC out-let complete all as specified and as directed.

Supply and fixing in repair 75 mm dia cast iron Nahani trap including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1(Using 20 mm graded aggregate) , complete all as specified and as directed.

Supply and fixing in repair 150x150 mm Salt-glazed stoneware gully traps, square or round mouthed, type 'P' complete all as specified and as directed.

Taking down carefully existing aluminium/copper point wiring on batten or in PVC conduit or in MS conduit with GI earth wire etc (for light, fan, socket or power ) complete and making good the disturbed surfaces of walls, Floors, ceilings etc to match with existing all as specified and directed.

Material and labour for concealed point wiring with FRLS grade PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with FRLS grade PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size through and including PVC conduit terminated in modular switch boards for fixing of switches, sockets, fan regulators etc for the following [Note: - Modular switch boards shall be measured and paid separately] (a) One light / fan point controlled by one switch

(b) One 3 pin 5 Amp socket outlet point controlled by one switch on same board with other switches

(c) One 3 pin 5 Amp socket outlet point controlled by one switch on independent board.

All as per item No. 122 above but wiring with FRLS PVC insulated unsheathed multistranded copper conductor cables of size 2.5 sqmm and cables of size 2.5 sqmm as continuous earth wire for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board complete all as specified and directed. [Note: - Modular switch boards shall be measured and paid separately]

Supply and fixing modular switch 1 way 6A, 1 module 250 volts complete all as specified and as directed.

Supply and fixing modular switch 1 way 16A, 1 module 250 volts complete all as specified and as directed.

Supply and fixing modular Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed.

Supply and fixing modular Socket, 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

Supply and fixing modular Fan step regulator, 120W - 2 module complete all as specified and directed

Supply and fixing modular Blank plate, 1 module complete all as specified and directed

Supply and fixing modular White cover plate with frame, 2 module complete all as specified and directed

Supply and fixing modular White cover plate with frame, 3 module complete all as specified and directed

Supply and fixing modular White cover plate with frame, 4 module complete all as specified and directed

Supply and fixing modular White cover plate with frame, 6 module complete all as specified and directed

Supply and fixing modular Metal flush box 1/2 module complete all as specified and directed

Supply and fixing modular Metal flush box 3 module complete all as specified and directed

Supply and fixing modular Metal flush box 4 module complete all as specified and directed

Supply and fixing modular Metal flush box 6 module complete all as specified and directed

Supply and fixing sheet metal enclosure for MCB DB double door single pole & neutral 8 way with common bus bar including taking down old one complete all as specified and directed.

Supply and fixing MCB 'C' series single pole 6 to 32 Amps, breaking capacity 10KA, complete all as specified and directed.

Supply and fixing MCB 'C' curve single pole neutral , 32 Amps with breaking capacity 10kA, complete all as specified and directed.

Supply and fixing Ceiling rose, 3 terminal, PVC/polycarbonate, isolated body complete all as specified and directed.

Supplyand fixing AC short circuit protection motor starter 25 Amps Capacity AC 230 Volt complete all as specified and directed. Make:- North /West/ Crabtree

Supply and fixing LED tube light fitting 20 watt (minm 110 lumen/watt), mounted on wall / ceiling connected with insulated unsheathed flexible copper wire of suitable size (length not exceeding 0.5 m) from ceiling rose complete all as specified and directed.

Supply and fixing LED recessed 2x2 luminaire 36 watt as in repair, flicker free illumination, minimum colour temperature 6000K, Luminair efficiency > 110 lm/w with suitable driver, white powder coated CRCA housing with seamles front frame with flat non-yellowwish diffuser,complete all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed. Make:- Bajaj, BZRSQL 36W GZi WH or equivalent in Halonix / Havells / Phillips

Supply and fixing submain wiring two single core 6.0 sqmm size stranded copper conductor PVC insulated unsheathed cable (FRLS) in and including PVC rigid non metalic conduit and one PVC cable 6.0 sqmm size FRLS grade copper conductor PVC insulated and unsheathed for contineous earth wire with junction boxes covered with laminated sheet 3 mm thick and other accessories including taking down old submain wiring complete all as specified and directed. Note: Two run of single core PVC cable with one run of green colour earth conductor and conduit shall be measured as one unit.

All as per item no -147 here in before but sub main wiring with 2 run of FRLS grade PVC insulated and unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm alongwith one run of FRLS grade PVC insulated & unsheathed copper conductor of nominal cross sectional area 4 sqmm as earth continuity conductor drawn through & including PVC conduit of suitable size complete all as specified and directed. Note : PVC Conduits/Casing-caping, two run cables and one run of earth wire will be measured as one length.

Supply, installation, testing and commissioning electric incinerator Capacity 10 Kg/ Hrs comprising of one electricity heated furnace for paper burning , cleaning of gas/ smoke coming out in the furnace, gas / smoke shall be enviromental friendly as per the parameters set by Polution Control Board, the cleaning system will of one cylinder separator and wet scrubber and suction blower with the following specification :- > Furnace size (a) Charging section 750mm x 500mm x 750mm (b) Air heating section 300mm x 500mm x 600 mm > Power requirement : 48 KW (for heating) > Size of cyclone separator : Dia - 500 mm, Height - 2000 mm (Made from MS). > Size of wet scrubber : Dia - 700 mm , Height - 2000 mm (Made from SS-304) > Size of setting chamber : 2000 mm x 1000 mm x 500 mm (MOC SS-304 with MS Angle support. > Water circulating pump - Monoblock type with 1 HP Motor. > Air Suction blower - Cap - 500 cfm at 6" Wg pressure, 2 HP Motor. > Control panel consisting of (a) Automatic temparature controller. (b) Switch, Starter of all Pump and Motor and heaters. Note : -Contracor shall be responsible for training of department personnel and users for running and maintenance of Electric Incinator . No extra payment shall be allowed for this. Contractor shall handed over all operating and maintenace manual of electrical incinator to the department before claiming payment.

Supply , laying and testing XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 70 Sqmm 3.5core complete all as specified and directed. Note: Excvation and earth work shall be measured and paid seperately

Material and labour for Sand cushioning with clean dry sand in trenches for protection of under ground cables (below, above and around the cable laid in trenches) complete all as specified and directed. (Note: Thickness after punning down shall be measured for payment)

Supply and laying well burnt bricks, sub class 'B' bricks laid breath wise across the length of cable above sand cushioning in trenches for protection of UG cables complete all as specified and directed.

Supply and fix triple pole and neutral metal plug and socket enclosure with a five pin earth plug and socket complete with one triple pole MCB 63 Amps capacity complete all as directed.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

PEARL CORPORATION

INDIA ELECTRICAL EQUIPMENTS