PROVN OF STORAGE SHED FOR WASTE OIL NEAR TECH STORE AND OXYGEN CHARGING BAY NEAR SUN SHELTER AT AF STN SONEGAON, NAGPURAT AF STN SONEGAON, NAGPUR

Amount

Excavation over areas in soft/ loose soil n. exc. 1.50m deep and getting out complete all as specified and directed.

Excavation in trenches in soft/ loose soil n. exc. 1.50m wide and n. exc. 1.50m deep for foundation, or for shafts, wells, cesspits, manholes, etc., n. exc. 10 sqm on plan getting out complete all as specified and directed.

Returning, filling in and including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

Removing excavated soil exceeding 250m and not exceeding 500m and depositing where directed complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for hardcore of broken stone or boulders of gauge not exceeding 63mm,deposited, spred and levelled in layer not exceeding 15cm thick, watered and rammed to true surface complete all as specified and as directed.

M&L 75mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

M&L for PCC 1:4:8, type D2, using 40mm graded stone aggregate as in foundation filling and mass concrete all as specified and as directed.

M&L for providing RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc., and mass concrete complete all as specified and directed.

M&L for providing RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for providing RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Use and waste of formwork to foundations, fillings, bases of columns, rafts & raft beams, sides & soffits of foundation & plinth beams and similar works; vertical or batter for rough finished surface of concrete complete all as specified and as directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, including supports, overhangs, etc. also splays between floors and beams complete of flat rough finished surfaces of concrete all as specified.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia and over up to and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-500D complete all as specified and as directed.

M & L for brickwork with flyash bricks using old size bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F sheet glass 3mm thick plain ordinary quality and glazing with oil putty wooden beads as directed in squares n. exc. 0.50 Sqm in each pane complete all as specified and directed.

S&F framed work such as grills, gratings etc., with ends of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks & similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

M&L for Fe 410-W (Gde-E- 250) quality-A Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.complete all as specified and as directed.

S&F Fe 410-W (Gde-E- 250) quality-A Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed.

M&L for Mild steel screw bolts 11 to 15mm dia (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt n exc 5cm long complete all as specified and as directed.

M &L for preparation new steel and iron surfaces not otherwise described exc 10cm width or girth and applying two coats of synthetic enamel paints over one coat of primer of red oxide complete all as specified and as directed.

S&f pre-painted galvalume aluminiun zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with J hooks including self tapping screws and self drilling screws of appropriate size with rubber washer for water tight fixing complete all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8, type D2, using 40mm graded stone aggregate as in sub base of flooring all as specified and as directed.

M&L for 40mm thick PCC 1:2:4, type B1, using 20mm graded stone aggregate as in sub base of flooring all as specified and as directed.

M&L for 100mm thick PCC 1:2:4 type B2, using 40mm graded stone aggregate as in ramps of flooring all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:4) on fair faces of brick work or concrete surfaces externally with water proofing compound finishing the surfaces even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid seperately.

M&L rendering 15mm thick in cement mortar (1:6) finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound

M&L preparation of newly plastered surface of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M&L for three coats of white wash on newly plastered wall surfaces including preparation of surfaces complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in coping, channels, water troughs and the like including weathering, slightly rounded or chamfered angles and throating etc. complete all as specified and directed.

M & L Glass dividing strips, 3 mm thick, width of strip is 28mm inserted into PCC floor complete all as specified.

M & L for Providing 1:2:4 Type B1, precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlockingjoints as directed) setting in CM 1:4 complete all as specified and directed.

M&L for point wiring complete with 1.5sqmm (nominal area) PVC insulated unsheathed multistranded, (two run for Phase and Neutral) copper conductor FR & LS grade cable of 1100V grade conforming to IS -694 drawn through and including new non metallic rigid PVC conduit medium grade, ISI marked, 20mm bore with conduit accessories concealed in wall/ floor and fixed on ceiling/ roof etc. including new pressed steel terminal boxes 1.6mm thick, concealed in walls with plastic laminated sheet cover 3mm thick as top cover fixed with cadmium plated screws for housing the switch sockets, outlets, fan regulator etc including provn of 1.5sqmm PVC insulated unsheathed copper conductor cable of green colour for earth continuity and connecting to common earth dolly etc., complete all as specified and directed for:-

One light/ fan point controlled by one switch.

Supply and fix switch piano, flush type, single pole, one way, 5 Amps, 230 volts all as specified and directed.

Supply and fix ceiling rose PVC/ Polycarbonate body 65 x 50mm 2 to 3 terminals 230 Volts, AC Single phase all as specified and directed.

Supply, fix, connecting and testing factory made, MCB distribution board (MCB DB), IP 38, SPN, 4 way, 240 Volts, double door, flush type made out of 1.2mm thick CRCA sheet metal, Phosphatised, duly powder coated and conforming to IS 13032 with 200 Amps rated bus bar, neutral link, earth bar and din rail etc. complete fixed in switch board/ wall complete all as specified and directed. Note: MCBs shall be measured and paid separately.

Supply, fix, connecting and testing MCB single pole and neutral (MCB SPN), 32Amps, 240 volts of rupturing capacity 10kA, C curve type complete all as specified and directed.

Supply, fix, connecting and testing MCB single pole (MCB SP), 6 to 32Amps, 240 volts of rupturing capacity 10kA, C curve type complete all as specified and directed.

Supply and fix LED tube light fitting capacity 20 watt fixed on wall/surface / ceiling with all accessories tube,driver,with surge protector complete wired with multistranded copper cable & connecting to ceiling rose with 3 core ,multistranded flexible copper cable complete all as specified and directed. Make CG CAT Part No- LDL-20-NW or its equivalent in Havells/philips/Bajaj.

M&L surface type point wiring for explosive storage accommodation with PVC insulated 1.5 sq mm multistranded copper conductor cable ,FRLS,1100 volt grade drawn in and including surface mounted ERW stove enamelled , black steel conduit not less than less 20 mm dia with and including flame proof bends and elbows, couplers, bell mouth reducer except junction box all as per relevent IS fixed with solid baked distance saddles ,and elevated MS spacer plate fixed with nettle fold GI screws along with 1.0 sq mm PVC insulated solid strand copper conductor FRLS 1100 Volt grade as ECC connected to common earth dolly for the following

One light point controlled by one rotary switch.

One ceiling/exhaust fan point controlled by one rotory switch.

All as per item No.45 here in before but point wiring with 2.5.0 sqmm multistranded copper cable for 5 Pin 15 Amp switch socket combination on Independent board with one run of 1.5 sq mm multistranded copper cable green colour for earth continuity conductor complete all as specified and directed.

S&F flame proof ON/Off rotory switch of cast Aluminium alloy SP 10/16 A 250V in LM -6 complete all as specified and directed.

S&F flame proof switch socket & plug combined in LM6 cable termination box in LM6, 16A, 250V, 2P+ earth complete all as specified and as directed.

S&F LED flame proof /weather proof light fitting suitable for 1X18/20watt LED tubelight fittings with built in control gear box as per relevant IS complete with accessories & 1 Nos of 18/20watt LED tube rod Complete all as specified and as directed. Make -: Shyaam switchgear Cat part no. SSPL/FF/1271 or its equivalent in Sudhir/flexpro.

S&F Flame proof DB 6 way with MCB DP 32A Capacity Construction with cable entries at bottom/Top for Incoming &2 no MCB 6 amp & 2 no MCB 16 amp as outgoing circuit Complete all as specified and as directed.

S&F flame proof /weather proof exhaust fan size 12'' as per relevant IS complete suitable for single phase 0.25 HP 240V complete all as specified and as directed. Make Shyaam Switchgear Cat part no. SSPL/MT/140/or its equivalent in Sudhir/flexpro.

Earthing complete with galvanized steel earth plate electrode of size 600mm x 600mm x 6.0mm thick burried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less than 1.5m below normal ground level, earth plate connected to galvanized iron earth lead wire of 4mm dia as earthing conductor by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES Schedule (Part I) (2009) connected to earth test point/ main switch/ DB/ Panel board all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 meter long for earth strip including PCC (1:3:6), type C-1 pit with 40mm thick precast RCC (1:2:4), type B -1 cover reinforced with 12mm dia MS bars @ 150mm c/c both ways with lifting hooks made out of 12mm dia MS bars, wire mesh funnel with watering pipe 20mm dia light grade, common salt, charcoal filling in layers as specified, necessary excavation and earth work in any type of soil etc., complete all as specified and as directed.

Removal of excavated materials to a distance not exceeding 50 mtrs and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Supply, lay / spread in trenches clean dry sand to required width and depth at bottom and top of cable including spreading, levelling, punning for laying/ cushioning of cable all as specified and as directed. Note : Punned thickness only will be considered or payment.

Supplying and laying common burnt clay sub class ‘B’ bricks of size 230 mm x 115 mm x 75 mm, laid perpendicular to axis of cable for protection of LT cables complete all as specified and directed.

Supplying & laying GI Tubing 40 mm dia Light grade pipe with connecting acessories complete in trench for road and on surface/,wall for protection complete all as specified and directed.

M & L road cutting of size 30 cm width x 45 cm depth for laying of cables including making good the road with necessary returning filling and bituminious portion with concrete and bituminious mixture and cemented portion with PCC in 1:2:4 , 15 cm thick from top and matching the surfaces with existing complete all as specified and directed.

Supply and lay in trenches/drawn through pipes or in road crossings / paths/ drains / ducts / floors / along poles / equipments etc., of LT cable under ground, XLPE insulated, screened, PVC bedded, galvanised strip or wire armoured, heavy duty electric cable with stranded aluminium conductor, 1100 volts grade of cross sectional area 10 Sqmm 2 core including connecting up using suitable size aluminium lugs testing and commissioning complete all as specified and as directed. Note : Excavation earth work, sand cushioning and brick protection shall be measured and paid separately.

M/s S. S. MUNDE