CA NO GE(H)-64/2023-24 SPECIAL REPAIR TO 6 Nos TOILET AND BATHROOM IN THE AOR OF AGE B/R-I UNDER GE HISAR AT HISAR MIL STN

Amount

M&L for treatment of sunken floor slab compraises of the following specifications and all as specified :- (i) M&L for cleaning the sunken/lowered portion of RCC slab surface (including vertical surfaces upto finished floor level) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely and providing 40mm thick avgerage PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in padding concrete to achieve proper slope including cutting holes in bricks or RCC wall for providing spout 50mm bore GI pipe medium grade of length 0.50m and fixed all as specified. (ii) M&L for providing rendering of uneven surfaces of vertical sunken with 6mm thick CM 1:4 mixed with integral water proofing compound @ 3% by wt of cement consumed. (iii) M&L for applying two coats of polymer modified cementious water proof coating (Sika / Fosroc / STP / Asian Paint )as per manufacturers instruction to bottom and vertical sides up to finished floor level and 100mm aove FFL , the thickness of two layer shall be 1mm and when the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed. (iv) M&L for providing plaster to the bottom and sides up to FFL with minimum 20mm thick CM 1:4 mixed with integral water proofing compound 3% by wt of cement consumed as per manufacturer's specification including rounding of corners and junctions sloping towards spout. Note :-(i) All junctions points of side wall where CI/GI pipes are passing through shall be sealed with epoxy putty. (iii) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean. (iii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint and cost is deemed shall be included in quoted rates. (iv) Cost of WPC shall deemed to be included in quoted rates. (v) Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage to the entire satisfaction of GE. Test shall be done in presence of reps of Engineer-in-charge and record for each sunken slab shall be maintained. (vi) The treatment shall be carried out in presence of Engineer-in-charge and tested. Cost of testing is inclued in the rates quoted above. (vii) For Payment purpose, the Plan area of Sunken floor shall be taken into account.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises

M&L for non skid ceramic jointless tiles (coloured) 1st quality, 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for glazed ceramic designer & pattern (dark & light shade) jointfree tiles (coloured) premium quality, 300mm x 450mm x 7-8mm thick, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in levelling course of floors and roofs 25mm thick finished fair & even complete all as specified & as directed.

Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts complete all as specified.

Taking down chowkat or frame with shutters area not exc. 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts complete all as specified

S&F 3mm thick polycarbonate solid sheet, in square/rectangular size, smooth surface, weather resistant, fine finish, bent and pressed including aluminium glazing clips, rubber beading and clear silicon or glazing with oil putty with putty or fixed with beads complete all as specified and directed.

Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed.

S&F for factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified & directed.

Supply & fixing butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified.

Supply & fixing aluminium handle 150mm size cast type, anodized complete all as specified.

S&F 200mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

Taking down steel windows/vents chowkat or frame with shutters area not exc. 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts complete all as specified

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete with glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete. Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete without glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete. Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of Zinc Chromate primer complete all as specified.

Demolition and breaking up drain pipes 150mm bore (Salt glazed stone ware, AC or Reinforced concrete) set in cement mortar complete all as specified

M&L for 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars all as specified & as directed

Material and labour PCC 1:3:6 type C-2 using 40 mm graded stone aggregate in concrete bed to drain pipes including forming cradles in after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc.

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed.

M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

M&L brick work using old size fly ash bricks as specified in clasue 6 of Particular specification, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

M&L rendering 10mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

Material and labour preparation of newly plastered/asbestos cement surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L for preparing the old decorated plastered /un plastered surfaces of ceilings including cornices by brooming down or steel wire brushing scrapping down or steel wire brushing scrapping down smoke soot etc and applying one coat of white wash to give uniform and smooth surface etc complete all as specified and directed.

M & L for rendering 15mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M&L for preparation of new plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer on walls all as specified & as directed..

M&L for preparation of old surfaces (plastered or unplastered) of walls including cornices, pilasters etc including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying one coat of oil emulsion distemper (OBD) of approved shade/tint all as specified & as directed

M & L for rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M&L for rough cast finish plaster by applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even complete .

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint on walls over a coat of primer all as specified & as directed.

M&L for preparing the old decorated plastered /un plastered surfaces of walls including cornices by brooming down or steel wire brushing scrapping down or steel wire brushing scrapping down smoke soot etc. and applying one coat of cement base paint of approved shade/tint on wall surface to give uniform and smooth surface etc complete all as specified and as directed.

Taking up or down 15mm bore steel tubing and connection incl cleaning for refixing or removal to store

Taking up or down 20mm bore steel tubing and connection incl cleaning for refixing or removal to store

Fixing only GI water tubing 15 mm bore, medium grade, with & including supply & fixing all new fittings (ISI marked) / connections & MS clamps / clips and necessary screwing as required complete and fixed with or without concealed to walls, ceilings or laid in floors complete all as specified and directed Notes :- (i) Old serviceable water tubing retrieved from serial item No. 38.00 here-in-before shall be used. (ii) Quoted rate shall be deemed to include cost of new GI fittings (ISI marked). Old fittings shall not be used.

Fixing only GI water tubing 20 mm bore, medium grade, with & including supply & fixing all new fittings (ISI marked) / connections & MS clamps / clips and necessary screwing as required complete and fixed with or without concealed to walls, ceilings or laid in floors complete all as specified and directed Notes :- (i) Old serviceable water tubing retrieved from serial item No. 39.00 here-in-before shall be used. (ii) Quoted rate shall be deemed to include cost of new GI fittings (ISI marked). Old fittings shall not be used.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

Dismantling old unserviceable PVC water tank capacity 250 ltr and not exc 500 ltrs & removal from site etc complete all as specified and directed.

Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks (colour other than black as approved by Engineer-in-charge) triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F in repairs Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore.

S&F in repairs Bib taps,cast copper alloy with crutch or butterfly handle, chromium plated, fancy type , screwed for iron pipe or for brass ferrule, for 15 mm bore GI pipe complete all as specified and directed.

S&F in repairs 20mm bore stop valve, fancy type , chromium plated cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified and directed.

S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms) complete all as specified and as directed.

S&F in repairs, PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks, cooler stand and similar work including welding conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

S&F mild steel framed work as in steel frames, chowkats, doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

S&F in repairs Grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40 gms) all as directed.

S&F in repair brass chromium plated overhead shower rose 125mm dia round shape with swivel joints complete all as specified and directed.

S&F in repairs vitreous china half stall urinal, 580mmx380mmx350mm (minimum), white with grating and union for discharge pipe includng providing and fixing plugs, bedding urinal against wall in CM (1:2), securing urinal to plugs with and including 60mm long brass screws complete with PVC flush pipe complete all as specified and as directed.

S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, with PTMT 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified.

S&F in repairs vitreous china counter top basin size 550 x 400 x 185 mm shape ovel of PARRYWARE / SOMANY / HINDWARE / PRAYAG as approved by GE including 32 mm CP waste coupling & PVC flexible waste pipe of 90 cm long complete all as specified & directed.

S&F in repairs vitreous china wash down water closet (Padestal pattern) White, including plastic water closet seat cover, black, closed pattern with flat bottom with mild steel chromium plated or aluminium hinging device and fixing with all joints including connection to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc complete all as specified and as directed.

S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F in repairs Plastic water closet seat, fancy type, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device.

Dismantling of cast iron pipes of any size of bore as in soil, waste or vent pipe including removal of cement joint fixed to wall or laid in floor complete all as specified and directed .

S&F in repairs 75mm bore pipe cast iron sand pipes for soil and waste and vent pipes in any length with our without cars , with cement joints laid in trenches or in floors or fixed to wall complete all as specified

S&F in repairs 110mm bore pipe cast iron sand pipes for soil and waste and vent pipes in any length with our without cars , with cement joints laid in trenches or in floors or fixed to wall complete all as specified

S&F PVC (SWR) floor trap dia of outlet 75mm, with PTMT grating including jointing with solvent cement.

S&F 75mm PVC (SWR) junction double, (double T) equal or unequal provided with access door complete all as specified and directed.

S&F PVC (SWR) 'P’ trap 110 mm bore complete all as specified & as directed.

S&F PVC (SWR) 'S’ trap 110 mm bore complete all as specified & as directed.

S&F as in repairs tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges.

M&L for 20mm thick Granite (of any type) tiles machine cut, as in steps, jambs, cooking plateforms and the like, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid over & including 20mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

S&F in repairs fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like.

Taking down carefully copper/aluminum point wiring (light/fan/socket or power) complete including taking out existing unserviceable terminal boxes & conduit with switches/sockets/fan regulators and fittings such as ceiling rose, pendants, tube light fittings, lamp holders, brackets light fittings, rectangular blocks etc. and making good disturbed surface of walls, floors etc. to match with the existing surface etc complete all as specified and directed.

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including concealed PVC rigid non metallic conduit 20/25mm dia medium grade (ISI marked) with all fittings such as tees, bends etc including sunk type pressed steel box covered with and including modular covered plate and frame for housing switch, socket, regulator etc’, complete, all as specified & directed. (Note :- Switches, sockets etc shall be measured and paid for separately under appropriate items of BoQ' ).'

All as per item No 75.00 (here-in-before) but ceiling fan /exhaust fan point controlled by one Number one way switch.

All as per item No. 75.00 (here-in-before) but for one 5 Amp socket outlet on independent board controlled by one Number one way switch on independent board

All as per srl item No. 75.00 (here-in-before) but for 15 Amp socket out let by using 2.50 Sqmm PVC insulated unsheathed copper conductor cable FRLS multi stranded on independent board including provn of 2.50 Sqmm unsheathed, multistranded copper conductor cable FRLS continues as earth wire connected to earth dolly etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs modular type switch 1 way 6Amp, 230Volts 1 moudle complete all as specified and directed

Supply and fixing in repairs modular type switch 1 way 16Amp, 230Volts 2 module complete all as specified and directed

Supply and fixing in repairs modular type socket 6Amp - 5 pin combined 2 module 230 volts AC complete all as specified and directed

Supply and fixing in repairs modular type socket 6Amp/16 Amp - 6 pin combined 2 modle 230 volts AC complete all as specified and directed

S&F modular ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed.

S&F sheet metal enclosure distribution board SP&N, 04 way, double door, powder coated, protection class IP-43, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating copper bus bar, complete all as specified & directed.

S & F MCB SP, 6 to 32 Amps 240 Volts , 'C' curve, 10 KA, IS-8828 marked for fixing in DB complete all as specified & directed. . Note :-Make of MCB shall be same of that DB.

S & F MCB SPN, 40 to 63 Amps 240 Volts , 10 KA, IS-8828 marked for fixing in DB complete all as specified & directed. . Note :-Make of MCB shall be same of that DB.

S&F in replacement LED light fitting 1x20W, regal batten for LED incl ultra bright glass LED tube light with very high efficiency, singel / double side connection all as specified and directed. Make : Havells Cat Part No LUMILINEBS20WLED865SPCWH of Havells or Crompton Cat part No CCS-100-20-65-HL2-DP-NWH or equivalent of makes as mentioned in Appx 'C' list of makes.

S&F Sub main wiring with two single core cable PVC insulated unsheathed of copper multi stranded conductor FRLS cable of size 6 sqmm, 1100 votls grade drawing through and including concealed conduit 25 mm dia medium duty including acessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 6 sqmm unsheathed multistranded FRLS copper conductor cable for earth continuity and connected to common earth dolly including cutting chasing of wall, if required and making good disturbed surface in CM (1:3) and finishig the surface to match with existing surface, etc complete all as specified and directed by Engineer-in-charge including taking down old unserviceable submain wiring. Note:- Two lengths of 6 Sqmm cable, one length of 6 Sqmm cable and one length of PVC conduit will be measured as one length.

Supply & fixing and testing steel body exhaust fan (Heavy duty) of 300mm sweep heavy duty, double ball bearing, 1400 RPM, suitable for SP 230 / 250 volt, 50 Hz AC supply complete with louver shutter including fixing / grouting of frame in wall & cutting opening complete with covers & connecting with & including 3 Nos 1.5 sqmm single core, PVC insulated but unsheathed FRLS 1100 volts grade cable with multi-stranded copper conductor from ceiling rose to fan complete.

Supply & fixing electric water heater, storage type mild steel body with glass lined coating (Outer body) with titanium armour technology inner tank coating for preventing corrison rusting and heating element upto 2KW cap 25ltr, BEE 3star rated complete with all accessories such as safety vlve, thermostate , NRV, connection piece etc complete & directed.

Shiva Constructin Co.

YASHU CONTRACTORS

M/S SM BUILDER CO

Balaji Construction Co.

M/S KAVITA CONSTRUCTION

M/s Rao Constructions, 1173 Urban Estate-II, Hisar

malik constructions

Puja Traders

M/S RR ENGINEERING CO