PROVISION OF CERTAIN SANCTION WORKS AT NDA KHADAKWASLA

Amount

Demolition of unreinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including cleaning off premises and removing rubbish off outside of MD land complete all as specified and directed.

Taking down chowkhats or frame exc 1.5 sq. m but n exc 4 sq m each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Demolition of brick / block masonry / Stone masonry built in Cement mortar etc complete all as specified and as directed.

M&L for 25 mm thick cement concrete type B-1, (1:2:4) (20 mm graded stone aggregate) as in sub base of tiles complete all as specified and as directed.

M&L for double charged vitrified coloured tiles light shade 10 mm thick (square/ rectangular) polished, area of each tile exceeding 0.36 sqm but not exceeding 1.00 sqm in floors etc, set and jointed in neat cement slurry and pointed with colour cement, laid over and including 15mm thick bedding layer in cement mortar 1:6, complete all as specified and as directed.

All as per item No.5 above but in skirting/vertical surface and including 10mm thick backing coat of CM 1:3 complete all as specified etc complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc including raking out joints,hacking for key ,scrubbing down with water etc complete all as specified and as directed.

M&L 15 mm thick plastering in CM 1:6 on wall including rendering is to be finished even and smooth (without using extra lime or cement) etc complete all as specified and as directed.

M&L for 10 mm thick plastering in CM 1:3 on ceiling including rendering is to be finished even and smooth (without using extra lime or cement) etc complete all as specified and as directed.

Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as directed

Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and as directed. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F for Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions false ceiling including sunk or raised moulding pattern approved by GE fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having Philips head with under head cutter at 200 mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish including necessary supporting hanger with 4.0 mm dia GI wire and 'J' bolts washer nuts for securing frame work to Gl frame work for (605 mm x 605 mm) seamless ceiling comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre incl thin layer of putty with gypsum binder, sanding the surface till smooth surface is obtained and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

S&F for factory made uPVC white colour Sliding window area exceeding 2 sqm each Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm),Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and as directed. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, allcomplete all as specified and as directed.

M& L for providing and applying plaster of paris putty of 2mm thickness to prepare the surface even and smooth and two coat of plastic emulsion paint, of approved manufacturer, and colour over a coat of wall primer complete as per manufacturer's specification complete all as specified and as directed.

S&F Door closer hydraulically regulated, designation No. 2,universal type, aluminium (Die cast) body suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed etc. complete all as specified and as directed.

S&F Steel rolling shutters 1.25mm thick, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete, gear operated type with bevel gear box and crank handle,etc. complete all as specified and as directed.

M&L for preparation of newly steel surfaces of any description over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer of any height complete all as specified and as directed.

S&F Elegant Tile made of perforated cement fiber composite 595x595/295X1195/595X1195x5mm covered with absorptive microfiber coating on the front side and Acoustics fiber on the back side, water resistance, fire resistant absorption coefficient upto 0.89 at 160 Hz tested as per ISO 354. The tiles are anti-sag and installed on T24 grid system of 0.6mm thick Main 'T' length minimum 3000mm, web minimum 35mm to be placed at 600mm center to center and secondary cross 'T' of length 600mm web minimum 35mm inter locked, Wire Support for Main T to be taken at every 1200mm length wise and 600mm width wise, with a backing of 50mm 1000 GSM thick absorb wool tested as per Fire Retardant IS 15061-2002 for excellent results.etc. complete all as specified and as directed.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and incl 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specified and as directed.

M&L for cement concrete (1:3:6) type C2 using 20mm graded stone aggregate in plinth protection, 75 mm thick, finished even and smooth without using extra cement, including making joints 12 mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen85/25 and sand in the proportion of (1:3) by weight complete all as specified and as directed.

M&L precast cement concrete (1:3:6) type C-1 (Using 20mm graded stone aggregate) block masonry with solid blocks exc10 cm thick in width and setting in cement mortar (1:6) complete in wall complete all as specified and as directed.

M&L for 15 mm thick cement plaster on brick or concrete surface in cement mortar (1:4) included finishing surface even and smooth without using extra cement on walls etc complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of Acrylic oil bound distemper over one coat of alkali resistant priming paint etc complete all as specified and as directed.

S&F MS powder coated 20 mm dia curtain rod including wooden polished brackets and wooden polished end knobs fixed with plugs & screws, complete all as specified and as directed.

Taking down of existing tarfelt and cement plaster of any description and thickness on roof top including flashing and junction of parapet and cleaning existing roof top surface by brooming , wire brushing incl removing the debris out complete all as specified and as directed.

Demolition of roofs, any thickness including plastering & leaping (whether full or part) removal of debris at a distance exc 250m but not exc 500m and depositing where directed complete all as specified and as directed.

M & L Cement concrete Type B0 1:2:4 ( 12.5mm graded stone aggregate ) in roof padding complete all as specified and as directed.

M&L for 15 mm thick rendering on concrete surface on roof in cement plaster 1:4 finished even and fair without using extra cement by using Liquid WPC @ 3% of wt of cement content complete all as specified and as directed. (Note: Water proofing Compound measured and paid separately)

Supply only Liquid water proofing compound complete all as specified and as directed.

M&L for APP based modified pre fabricated five layer 3 mm thick and weighing not less than 3.6 Kg/Sqm water proofing membrane reinforced with polyester non woven fabric mat with 160 gm/Sqm black finished with compatible primer conforming to IS 3488 @ 0.30 Lit/ Sqm and bonding material 85/25 bitumen 1.2 Kg/Sqm before and after laying membrane laid by torch application side overlap of 100 mm and over lap of 150 mm longitudinally, At the junction of roof and parapet wall a grove of 20 x 20 mm shall be made at the ht of 100 mm and membrane shall be inserted and sealed with bituminous mastic joints/overlap shall ve saled with hot bitumen 85/25. Two coat of water proofing aluminium paint on top of APP membrane shall be applied complete all as specified and as directed.

S&F for 1.00 mm thick plain galvanised, mild steel sheeting as in ,gate, ridges hips, valley gutters, drip qnd straight flashings with grade of zinc coating 275 gm/Sqm and fixed with nut bolt complete all as specified and as directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde E-250 quality A ) complete all as specified and as directed.

S&F rolled mild steel in Joist, channel, angle, or tee sections,fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe-290 (Gde E- 165 ) complete all as specified and as directed.

Taking down rain water pipes (any size or pattern) including all fitting heads, shoes, bends swan -necks,complete all as specified and as directed.

Supply and Fixing 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floors including suitable clamps after every one meter of interval complete all as specified and as directed.

S&F for 110mm dia PVC (SWR) bends any radius complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft /loose soil etc complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft / disintegrated soil etc complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. Soft/disintegrated loose soil etc complete all as specified and as directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point etc complete all as specified and as directed.

M&L for Hardcore of gauge stone boulders n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M&L for PCC in foundations, filling and mass-concrete type C-2 (1:3:6) using 40 mm graded stone aggregate etc complete all as specified and as directed.

M&L for 100 mm thick PCC, Type C-2, 1:3:6, (using 40 mm graded aggr) as in sub base etc complete all as specified and as directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering etc complete all as specified and as directed.

M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces of walls in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:3) with using extra cement etc complete all as specified and as directed.

M& L for Neeru finish to plastering surface upto FFL etc complete all as specified and as directed.

M&L for RCC type B1 (1:2:4) nominal Mix using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for RCC type B1 (1:2:4) nominal Mix using 20 mm graded stone aggregate as in Column, Pillars piers, posts and struts etc complete all as specified and as directed.

M&L for RCC type B1 (1:2:4) nominal Mix using 20 mm graded aggregate in as lintels over 1.5m span etc complete all as specified and as directed.

M&L for RCC type B1 (1:2:4) nominal Mix using 20 mm graded aggregate in as Chajjas over 1.5m span etc complete all as specified and as directed.

M&L for Reinforced cement concrete (nominal mix) type B-1 using 20 mm graded stone aggr Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as spd and as directed.

All as per item No.55 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders etc complete all as spd and as directed.

M&L for use and waste for Formwork to flat sides and soffits of slab, floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for preparing of new surface of walls and applying of two coats of Cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 etc complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 18-20 mm thick over 15 mm thick screed bed in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete etccomplete all as specified and as directed.

All as per item No 60 above but in skirting over 10 mm thick CM 1:4 etc complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigment etc complete all as specified and as directed.

M&L for Sand cushioning under paver block including watering and consolidation etc complete all as specified and as directed.

M&L for 25mm thick DPC 1:2:4 type B-0 using 12.5 mm graded stone aggr etc complete all as specified and as directed.

M&L for providing Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including demolition of existing broken stone and making drainage opening wherever required complete all as specified and as directed.

M & L 100mm thick cement concrete type D2, 1:4:8 (Using 40mm graded granite stone aggregate) as in sub base including use of necessary form work complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed.

M&L for PCC 1:2:4 Type B1 (using 20 mm graded stone aggregate) as in mud stops, rounded or chamfered edges etc complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in hard/dense type of soil complete all as specified and as directed.

M & L cement concrete type D2, 1:4:8 (Using 40mm graded granite stone aggregate) in foundation filling and mass concrete complete all as specified and as directed.

M&L for Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including fabrication, distance pieces, cleats etc. complete all as specified and as directed.

M&L for gussest plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment etc confirming to Fe 410-W (Gde-E-250 Quality-A) complete all as specified and as directed.

S&F mild steel screw or bolts (machine made) with hexagonal or square heads at one and screwed the other, or screwed both ends each screwed end to be filled with washers and hexagonal or square nut ,not exceeding 5cm long and diameter of neck 5 to 10mm complete all as specified and as directed.

M&L for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Taking down existing copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

M&L for concealed point wiring in and including new PVC conduit medium grade with the help of multi-stranded unsheathed FRLSH copper cable 1.5 sqmm 650/1100V conforming IS:3419 -1988 adhering to colour code including earth wire of the size 1.5 Sqmm green colored with modular steel or cast iron terminal boxes and modular cover plates as required at site including making good the disturbed surfaces and matching it with existing surface for the following :- (a) One light/Fan point controlled by one way switch 6 Amps 240 volts complete all as specified and as directed.

All as per above item No.76 but for (b) One 3 pin socket outlet, 5/6 Amps on the same board with other switches complete all as specified and as directed.

All as per above item No.76 but for (c ) One 3 pin socket outlet, 5/6 Amps, independent complete all as specified and as directed.

(d) M&L concealed point wiring with 4 sq mm copper conductor FRLSH (multistrand) PVC insulated ISI marked unsheathed cable in and including PVC conduit not less than 25 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 4 sq mm copper conductor as earth wire to common earth dolly complete all as specified and as directed.

S&F modular switch 1 way 10 A 1 module complete all as specified and as directed. .

S&F Modular socket 6 A 2/3 Pin 2 module complete all as specified and as directed.

S&F modular switch 1 way 16 A 1 with indicator module complete all as specified and as directed.

S&F Modular socket 6 A/16A 2/3 Pin 2 module complete all as specified and as directed.

S & Ff RJ-11 telephone socket with transparent shutter 2 module alongwith flush metal box 2 module and front cover plate 2 module complete all as specified and as directed.

S &F for LAN RJ-45 Jack With Cat 6 socket UTP Cat with transparent shutter 1 module alongwith flush metal box 1 module and front cover plate 1 module complete all as specified and as directed.

S &F for HDMI socket with transparent shutter 1 module alongwith flush metal box 1 module and front cover plate 1 module complete all as specified and as directed.

S&F in replacement for ceiling rose, 3 terminals /PVC/Polycarbonate, isolated body complete all as specified and as directed.

M&L for Provn of PVC conduit for Telephone/TV/ LAN/ CCTV/PA not less than 25 mm with Cutting chases for concealed for Telephone/TV/LAN/ CCTV/PA wire, pinning in and making good to surface where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., cutting not exc 10 cm girth including 3 mm thick wall care putty on wall, making surface matching to adjacent surface complete all as specified and as directed. Note: a. Rate quoted shall deemed to include cost of taking down existing Telephone/TV/LAN/ CCTV/PA wire. b Rate quoted shall deemed to include cost of relaying existing Telephone/TV/ LAN/CCTV/PA wire through PVC conduit.

Taking down ceiling fan/Exhaust Fan, sealing cable end, dismantling blades and removing fan and blades to MES store yard complete all as specified and as directed.

S&F in repalcement surface mounted 2' x 2' LED Panel lights 35/36 W LED 6500K, 240Volts and glare free symmetrical illumination suitable for ceiling, Environmental friendly, new generation, energy saving, high power LED as a light source with clear diffuser including connecting with twin core wire and also matching to the adjacent ceiling surfaces carefully complete all as specified and as directed. Note: The quoted price shall include the cost of Light and its driver.

M&L for Cutting chases for concealed conduit wiring, pinning in and making good to surface where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., cutting not exc 10 cm girth including 3 mm thick wall care putty on wall, making surface matching to adjacent surface complete all as specified and as directed.

Taking down existing copper/aluminium sub main wiring complete for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed

M&L for concealed sub main wiring with two single core PVC insulated FRLSH cables with stranded copper conductors 2.5 Sqmm , 1100 Volts grade in and including PVC conduit medium grade with all fitting & other accessories and copper cable 2.5 sqmm continuous earth wire complete all as specified and as directed. Note: Two runs of 2.5 Sqmm cable with 01run of 2.5 Sqmm earth wire along with PVC conduit medium grade shall be measured as one RM

M&L for concealed sub main wiring with two single core PVC insulated FRLSH cables with stranded copper conductors 4 Sqmm , 1100 Volts grade in and including PVC conduit medium grade with all fitting & other accessories and copper cable 4 sqmm continuous earth wire complete all as specified and as directed. Note: Two runs of 04 Sqmm cable with 01run of 4 Sqmm earth wire along with PVC conduit medium grade shall be measured as one RM

M&L for concealed sub main wiring with Four single core PVC insulated FRLSH cables with stranded copper conductors 6 Sqmm , 1100 Volts grade in and including PVC conduit medium grade with all fitting & other accessories and copper cable 4 sqmm continuous earth wire complete all as specified and as directed. Note: Four runs of 06 Sqmm cable with 01run of 6 Sqmm earth wire along with PVC conduit medium grade shall be measured as one RM

Supply and fixing factory made epoxy powder coated Distribution Board TP & N 4 way double door (VTPN MCCB DB) MCCB as In comer, with metal door (IP-43 protection) fabricated from CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout flush to wall and making good disturbed surface and touch up with the same finishes complete all as specified and as directed. Note: MCBs/ MCCBs will be measured and paid separately under respective Sch A item in the schedule

S&F in replacement of MCCB with rating of 125 Amps, 415 Volts 4 pole with 16 kA breaking capacity, thermal magnetic adjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capacity(Icu). MCCB should be with suitable spreaders and phase barriers for each terminals complete all as specified and as directed.

Supply and fix in replacement sheet metal enclosures single pole MCB 20 Amps with a two pin and earth plug and socket complete with all accessories etc complete all as specified and as directed. Make: Legrand Cat part: 5078 10 or equivalent make mentioned at list of makes in PS

S&F in replacement MCB DB 8 way SPN Double door sheet metal enclosure factory made suitable for MCB DB's 240 volts,concealed in wall complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete all as specified and as directed. Note - MCBs will be measured & paid separately under respective item of sch A, if required to be replaced.

S&F MCB SP 6 to 32 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing complete all as specified and as directed.

Supply and fix MCB SPN 40 -63 Amps working on 240 volts, 50 HZ,10 KA C Curve complete all as specified and as directed.

Earthing complete with galvanised iron earth plate electrode 600 x 600 x 6mm as earthing lead buried directly in ground vertically to depth not less than 2.25 mtr below GL with the top edge of the plate not less than 1.5 mtr from GL, connected to GI earth lead of 4.0mm dia, by means of bolts & nuts, to GI and connected to earthing test point all as shown in electrical plate No. 3 of SSR Part-I of 2009* specified or indicated and testing on completion including excavation / earth work in any type of starta, PCC (1:3:6) type C1 earthing chamber pre cast slab 50 mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric (XPM) weight not less than 4 KG/sqm cast iron frame, funnel with wire mesh GI watering pipe of 20 mm bore medium grade and lugs with and including GI earth wire 4 mm dia with GI protection pipe of 15 mm medium grade 7.5 meter long etc complete tested on completion complete all as specified and as directed. Note: a. Rate quoted shall deemed to include cost of excavation in any type of strata, RFR and removal upto 50metre, PCC pit, funnel and RCC cover plate. b. GI wire above 7.5m will be measured and paid separately.

S & F copper earth continuity conductor or main earthing lead of size 20 x 3 mm fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe with green colour code or fixed to pole or any other indicated situation for earthing,Porcelain insulator etc. as required complete all as specified and directed

Supply and Laying including testing LT UG Power cable, XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with multi-stranded aluminium conductor including termination with LT Panel/Feeder Pillar with galvanised or Cadmium plated high tensile nuts, bolts and washers etc including Sheddling /clamping on any type of wall with suitable size of GI Clamps, nuts, bolts & washers etc complete all as specified and as directed of following size :- (a) 3.5 Core 50 Sqmm

All as per item No.104 above but in 4 Core 25 Sqmm

Excavation in trenches, n.exc 1.5m wide and n. exc 1.5 m depth and getting out in soft/loose soil for foundation of pole, stay, laying of cable and pipe etc complete all as specified and as directed.

Excavation in trenches, n.exc 1.5m wide and n. exc 1.5 m depth and getting out in hard dense soil for foundation of pole, stay, laying of cable and pipe etc complete all as specified and as directed.

Returning and filling in, including spreading and well ramming in layers n exc 25 cm in soils complete all as specified and as directed.

Supply and laying 63 x 50 mm outer & inner dia, double walled corrugated (DWC) HDPE duct pipe confirming to IS-16205 Pt-24 with antirodent and non flame propogating properties of approved colour complete with fittings i.e.coupler,Tee, elbow clamp for cable protection of size 50 Sqmm 3.5 core complete all as specified and as directed.

Supply and laying 40 x 32 mm outer & inner dia, double walled corrugated (DWC) HDPE duct pipe confirming to IS-16205 Pt-24 with antirodent and non flame propogating properties of approved colour complete with fittings i.e.coupler,Tee, elbow clamp for cable protection of size 16 Sqmm 4 core complete all as specified and as directed.

Supply, installation, testing and commissioning LT Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-54, front side double door type with locking arrangement and nut-bolts for back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber. The panel shall be provided with aluminium bus bars, electrolytic grade of 200 Amp Current rating. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and Cable connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers including suitable Lugs etc. The panel shall be provided with digital multifunction meter 4410 Series, Accuracy Class 1 with RS 485 Parameters with cast Resign CTs and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board etc. The panel shall be provided 4 Nos 50x50x6mm thick angle iron supports of not less than each 1 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both sided and suitable extended rotary handle for Incoming MCCB complete all as specified and as directed. The overall size of the panel shall not less than 800mmX450mmX 1000mm (LxDxH). The panel shall be provided for Cable entry from bottom side for 04 No of Cable upto 70 Sqmm 3.5 Core with suitable size of SS Cable Glands including 2 Nos of Earting Terminals one on each side of the Panel with earth strip and including following accessories:- Note : Before manufacturing drawing and design of panel including size & length of busbar shall be approved (a) MCCB 4 Pole, 415 Volts, 125 Amp, 16 KA Breaking capacity with adjustable Thermal and adjustable Magnetic overload protection with Ics = 100% of Icu including suitable size of spreader links and phase separator on both side. (Incoming) - 01 No. . (b) MCCB 4 Pole, 415 Volts, 63 Amp, 16 KA Breaking capacity with adjustable Thermal and adjustable Magnetic overload protection with Ics = 100% of Icu including suitable size of spreader links and phase separator on both side. (Outgoing) - 02 No. (c) MCB 4 Pole, 415 Volts, 63 Amp, 10 KA Breaking capacity conforms to IEC 60947-2. (Outgoing) - 01 Nos.

S&F GI tubing 'light grade' 50 mm dia ISI marked with all fittings laid in trenches and fixed on pole by flat iron clamps, nut, bolt, washer of suitable size complete all as specified and as directed.

M & L for bituminous road cutting by using suitable hydraulic road cutter for a width not exceeding 300 mm and depth 500 mm for laying/passing of 80 mm dia medium grade GI pipe incl refilling and making good with existing material to match with the existing surface complete all as specified and as directed.

S & Fix of Cable Route Marker made up of Cast Iron of dia 100 mm and thickness 4.65 mm with supporting angle iron of size 20 x 20 x 3 mm and height 1 mtr for stand including priming, painting and wirting of "MES LT CABLE" with Arrow Direction in suitable size of letter including necessary earthwork and grouted at suitable depth in PCC 1:3:6 Type C2 using 40 mm graded aggregate in mass concrete complete all as specified and as directed.

M & L for earthing complete with galvanized steel earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.50 m deep below normal ground level in any type of soil strata, connected to galvanized iron strip 25 X 4 mm by means of bolts, nuts and washers of galvanised iron or steel all as shown in earth plate No 3 of MES schedule 1991 Part – I connected to Change over switch panel including necessary excavation and earth work, concrete pit & chamber,pit cover made of PCC 1:2:4 type B1 with lifting handle and Earth lead and 20 mm Dia GI watering pipe medium grade, Funnel, wiremesh, etc. complete all as specified and as directed.

S&F modular BLDC fan regulator, 2 module, suitable for ceiling fan of 1200/1400mm sweep complete all as specified and as directed.

S&F for Ceiling rose 3 terminals /PVC /Polycarbonate isolated body complete all as specified and as directed.

Suplying and fixing LED tube light fitting complete with all fitting and fixing accessories, 1X20 Watt pre-wired with high efficiency electronic driver,glare free,smooth light distribution complete all as specified and as directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Supply and Laying of UG LT cables XLPE insulated, PVC sheathed aluminium conductor multi stranded armoured heavy duty 1100 Volts grade cross sectional area 10 Sqmm 2 core laid in trenches / ducts/ along poles / through pipe under road etc with new aluminium lugs of cable size complete all as specified and as directed.

Material and labour for cutting of existing road/ hard standing by providing suitable T&P to make suitable size trench for laying 40mm dia pipe in road crossing etc. including the cost of making good the disturbed surface and matching with existing (Chequered tiles/Road/PCC) complete all as specified and as directed.

Supply & Fix GI tubing medium grade 40 mm dia ISI marked with all fittings laid in trenches and fixed pole by flat iron clamps, nut, blt, washers suitable size complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16sqmm 4 core complete all as specified and as directed.

Supply and laying 40 mm outer dia, double walled corrugated (DWC) HDPE duct pipe confirming to IS-16205 Pt-24 with antirodent and non flame propogating properties of approved colour complete with fittings i.e.coupler,Tee, elbow clamp for cable protection complete all as specified and as directed.

M & L of installation of a complete electrical incinerator system 50 Kg burning capacity designed for the efficient and secure disposal of paper waste. This includes the supply and delivery of an electrical incinerator unit with a specified capacity and Burn Rate - Per hour,PLC Control Mode, Manual Feed Mode,7 - 15 KW Power 415 V/ 3 phase Voltage ,Digital Display ,Chimney ht 5 ft,Stainless Steel/ Mild steel Chimney , 1st. chamber temperature 800°C~1000°C, 2nd. Chamber temperature 900°C~1100°C ,Residency Time 2.0 Sec. , along with all necessary accessories for proper operation. The incinerator shall be equipped with features such as automatic temperature control, ash collection, and appropriate safety mechanisms. The system also includes installation, electrical connections, testing, and commissioning to ensure proper functionality and compliance with safety and environmental standards complete all as specified and as directed.

S&F MCB DB 04 way SPN single door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and existing circuits complete all as specified and as directed.

S&F MCB TPN 40 Amps 415V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing complete all as specified and as directed.

Supply and install Hi wall split type AC units indoor/outdoor complete with cordless remote control unit and with in built air ioniser invertor type compressor, 100% copper tubing of Indoor & Outdoor cooling & condenser unit respectively with CFC free gas for better indoor air quality with 5 star rating and EER 3.2 of capacity 2.0 TR single phase including cabling work, insulation between indoor unit to outdoor unit and provision of MS Brackets for resting of outdoor units (where reqd) or making resting platform of outdoor unit by brick works complete all as specified and as directed. Make : Carrier/Daikin/Hitachi/Blue Star.

S & F voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 270 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA complete all as specified and as directed. Make : V-Guard/ Vinitec/ Microtek.

S & F sheet metal enclosures single pole and neutral enclosure with a two pin and earth plug and socket complete with one MCB SPN 20 Amps, complete all as specified and as directed.

M&L for high thermal conductivity and corrosion resistant Copper Tube of size 1/4 inch (6mm) with nitrile rubber insulation including all fittings and fixing accessories used in extended length complete all as specified and as directed.

M&L for high thermal conductivity and corrosion resistant Copper Tube of size 5/8 inch (16mm) with nitrile rubber insulation including all fittings and fixing accesssories used in extended length complete all as specified and as directed.

M&L for PVC pipe 20 mm dia heavy duty with all fittings and fixing accesssories such as coupler, lock nut, saddle, pipe hook and laid on floor (for drain line) complete all as specified and as directed.

M & L for making holes by core cutting machine on stone/concrete / brick walls.Dia of hole not exc.50mm and thickness of wall 50cm to 70cm for entry of suction and discharge pipes of AC and making good disturbed surfaces with cement morted and finally finished with plaster of paris and painted the disturbed surfaces with existing type of paint and tint complete all as specified and as directed.

M&L for sub main wiring 2 x 4.0 Sqmm for phase and neural, 1 x 4.0 Sqmm for earth wire PVC insulated (heavy duty) 1100 volts grade, FRLSH, with single core copper conductor in & including PVC casing caping of suitable size not less than 25mm complete all as specified and as directed (from distribution board to metal clad switch socket point near AC). Note: Two run of 4.0 Sqmm and one run of 4.0 sqmm as earth wire cable alongwith PVC casing caping will be measured as one RM

SUN Enterprises (BID ID -3497610)

Mehta and Co. (BID ID -3499841)

M/S Narendra Construction (BID ID -3493130)

Elite Constructions (BID ID -3499568)

agarwal and company (BID ID -3499843)