PROVN OF MODULAR KITCHEN IN OFFRS MD ACCN AT PRATAP PARK AND CERTAIN REV WORK NO. 49, 51, 55, 59, 60, 62, 63, 64, 67 UNDER GE (EAST), MATHURA

Amount

S&F precast reinforcement concere M-25 (Desing Mix) and set in CM 1:4 as in manhole cover slab etc complete all as specified and direted.

M&L TMT bars 6 to 8mm dia, and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., complete.

Dismantling asbestos cement corrugated or semi corrugated sheets in roof covering incl ridge.

Dismantling of timber scantlings 40 Sqcm & over in section in any position in framed work in fillets rails posts rafters purlins in framed work

S&F Steel work in trusses fabricated with rectangular / Square hollow section, including special shaped, washers etc including cutting welding, bending in shape etc using tube of YST 310 grade confirming to to IS-4923 complete all as specified & directed.

M&L cement concrete M-15 grade (Nominal mix) using 20mm graded stone aggregate as in bed blocks for fixing hold fasts and fillling of chowkhats etc. all as specified.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws complete.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws complete.

S&F MS flat iron wind ties for roof including all necessary drilling, bolting or riverting etc complete all as specified and as directed.

Dismantling wall and ceiling boards (Fiber pulp, insulation etc or insulation boards any thickness including cover fillets.

Providing and fixing inter locking metal grid (snap grid for false ceiling) of size 605 mm x 605 mm in true horizontal level, hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24 mm X 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200 mm x 600 mm and secondary cross “T” of length 600 mm and size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 mm X 600 mm panel to form grids of 600 mm X 600 mm and wall angle of size 24 mm X 24 mm X 0.4 mm. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 mm X 37 mm X 25 mm X 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 mm X 30 mm X 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications and as directed by Engineer-in-charge.

M&L 4mm thick designer non-asbestos fibre cement building board having fire resistance & mosture resistance properly. Make :- Everest, fixed on aluminium grid with screws complete all as specified and directed.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation, laying cable etc and getting out soft / loose soil complete.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames exc 1.5 sqm but n exc 4 sqm each.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames not exc. 1.5 sqm each.

S&F 105x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and as directed.

S&F 125x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and as directed.

Cutting holes in brick walls, built in CM for inserting hold fasts and making good dismantled portion in CM 1:3 OR cement concrete M-15 grade (Nominal mix) using 20mm graded stone aggregate depth of embedded portion of hold fasts or lugs measured from the face of the jambs into the wall exc half brick but not exc one brick.

S&F 40 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides.

S&F 35mm thick second class HW glazed and gauged skeleton shutters open rebeted and prepared to receive glass, guaze etc (without sash bar) edges of framing plain chamfered or rounded fitted with cut and beads for securing glass, gauge etc size of shutters as specified in SSR Part-I section & clause 8.20(a).

M&L for prepration of new wooden surfaces, exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and as directed by Engineer-In-Charge.

M&L for preparation of new steel surfaces exc 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of Red Oxide primer all as specified.

S&F 125 mm long extruded aluminium alloy handles, fabricated type anodized complete.

M&L for 100mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

Supply and fix Stainless steel wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples

S&F in repair floor door stopper of Aluminium anodised body,double leg type with hard drawn rubber shoe 150 mm size.

S&F100mm long Butt hinges, medium weight, cold rolled mild steel, and fixed .

S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforcement with MS square tube supplying and fixing in opening as per specification & sketch shown in sketch 8 of SSR part II.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck indie with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fittied in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level).

M&L 40mm thick PCC M-15 grade (Nominal mix) using 20mm graded stone aggregate as in sub floor all as specified & directed by Engr-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding/complete and removing rubbish off the premises.

M&L for coloured joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified.

M&L for coloured joint free Non - skid Ceramic tiles 10mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:3 complete all as specified.

M&L for coloured Glazed ceramic tiles on vertical surface 450x 300x 7 mm/ 300X 200X 7mm thick set and jointed in dado/skirting over & including 10mm thick rendering in CM 1:3 as in backing coat & pointed in neat cement slurry and jointed in white or colour cement to match.

Surface dressing n.exc 15cm deep in soft/loose soil.

Surface excavation in soft/loose soil, not exceeding 30cm deep and averaging 15cm deep and getting out complete.

M&L for PCC M-7.5 grade (Nominal mix) using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as directed.

M&L brick work with old size fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified

M&L for Brickwork with old size flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified.

M&L for Brickwork with old size flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified.

M&L for 40mm thick Damp proof course in cement concrete M-15 grade (Nominal mix) using 12.50mm graded stone aggregate on horizontal or vertical surfaces including water proofing compound & necessary form work all as specified. Note : Water proofing compound shall be measured and paid for separately under relevent item of this BOQ

Supply only liquid water proofing compound.

Returning, filling in, in-cluding spreading, levelling, watering and well ramming in layers not exc 25 cm. thick complete all as specified and directed by Engr-in-charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

M&L for providing reinforcement concrete M-25 grade (Design mix) in lintel/chajja

M&L for RCC M-25 grade (Design mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like.

M&L for steel reinforcement of TMT bars (FE-500 Grade) 10 mm dia and over cut to length and bent to shape required including cranking bending spirally for hooping for columns hooking end and binding with mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips all as specified and directed.

All as per item No. 49 above but 5mm to 10mm dia as in striups, spacers & binders all as specified.

M&L for use & waste of steel form work (rough finished flat) to sides and soffit of roof slab, shelves etc n. exc 200mm thick etc complete all as specified and as directed.

M&L for use & waste of steel form work (rough finish flat) to edges of concrete flat, roof slabs not exceeding 200mm thick shelves etc for rough finished surface complete.

Filling with earth obtained from excavation including spreading, watering, levelling and consolidation in layers not exceeding 25 thick complete.

M&L for hardcore of broken stone or boulder gauge n exc 63mm, deposited, spread and levelled in layers n exc 15cm thick watered and rammed to true surface.

M&L for 50mm thick cement concrete M-10 grade (Nominal mix) using 20mm graded aggregate, complete finishing surface even and smooth without using extra cement all as specified and as directed by the Engineer-in-Charge

M&L for 75mm thick cement concrete M 7.5 grade (Nominal Mix) using 40mm graded stone aggregate as in sub base flooring complete.

M&L for providing 25mm thick M-15 grade (Nominal mix) using 20mm graded stone aggregate as in floor finish complete.

M&L for providing 100mm thick M-15 grade (Nominal mix) using 20mm graded stone aggregate as in floor complete.

M&L for coloured Glazed ceramic tiles on vertical surface 300x 450x 7 mm thick set and jointed in dado/skirting over & including 10mm thick rendering in CM 1:4 as in backing coat & pointed in neat cement slurry and jointed in white or colour cement to match.

M&L for rendering 15 mm thick on other than fair faces of brick wall or concrete surface in cement mortar 1:6 finished even & fair all as specified and directed.

M&L for rendering 10 mm thick on other than fair faces of brick wall or concrete surface in cement mortar 1:4 finished even & fair all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for newly plastered surfaces of wall and applying two coats of oil bound distember over one coat of primer over a coat of wall care putty not less than 1mm thick including preparation complete.

M&L for preparing newly plastered surface of ceiling and applying three coats of white wash complete all as specified.

S&F 150 mm long extruded aluminium alloy handles, fabricated type anodized complete.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S&F aluminium louvered ventilators of section size 100mmx25mmx1.50mm including frosted glass fixed in half protion & adjustable type louvers in another hald and stainless steel wire mesh fixed type on outside frame etc. including taking down existing steel ventilator all as directed by Engr-in-charge

S&F 500 liters capacity rotational moulded polyethylene three layer water storage tank (Cylindrical vertical with close top) hoisted and fixed in position including connections including dismantling existing old water storage tank all as specified.

Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed

Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed

S&F in repair 20 mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white including Plastic water closed seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device fixed complete all as specified and directed.

S&F 110mm cast iron traps 'P' or 'S' for water closet.

S&F vitreous china wash hand basin,white, flat back size 580x450 mm excluding taps, waste chain & plug & porcelein stopper but including brackets 32 mm bore waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly-nuts, flange end bedded in red lead cement cutting for and pinning in ends of brackets all as specified and directed.

S&F vitreous china wash hand basin,white, flat back size 580x450 mm including CP pillar tape fancy type suitable for 15 mm bore pipe 32 mm bore CP brass waste coupling and brackets complete all as specified.

S&F angle cock/valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed with ends for iron pipe or union and fixed of 15mm dia. Make :- Cat part No ESSCO APR-101053 all as approved by Engr-in-charge.

S&F 15mm bore bib tap, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified.

S&F wash basin mixer 15mm bore all as specified. Make:- ESSCO cat part No APR 101011B or equivalent make given under list of make.

S&F 15 mm bore PVC connection with PTMT nuts of length 450 mm.

S&F Gun matel, globe or gate valves 20 mm bore dia, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F PVC (SWR) bends of any radius 75 mm bore complete.

S&F PVC (SWR) floor trap plain with grating including jointing with solvent cement dia of out let 75 mm including stainless grating fixed complete all as specified and as directed.

S&F PVC (SWR) bends 110 mm bore with or with out oval excess door complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) pipes type 'A' single socketed in any length with rubber ring joints laid in trenches.

S&F 75 mm dia PVC (SWR) pipes type 'A' single socketed in any length with rubber ring joints laid in trenches.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete M-15 grade (Nominal mix) smooth finished, and reforming benching as required 150 mm bore of pipes.

M&L salt-glazed stoneware drain pipes grade 'A' 150mm dia laid in trenches and jointed as specified.

M&L for Concrete bed to drain pipes M-7.5 grade (Nominal Mix) using 40mm graded stone aggregate bore of pipe 150 mm including packing under, and haunching against the sides of pipes after they are laid and tested.

M&L for 10mm thick rendering in cement mortar (1:4) on fair faces of brick/concrete surfaces finished the surface even and smooth without using extra cement complete.

M&L rendering 10mm thick in CM 1:6 on fair surfaces of Brick wall and concrete surface fair finished even & smooth without using extra cement.

M&L for preparation of new plastered surface of walls and applying two coats of oil bound distemper over a coat of Alkali resistant primer complete all as specified and as directed.

M&L preperation of newly plastered surfaces & applying two coats of oil bound distember over a coat of alkali resistant primer complete.

M&L for preparing newly plastered surfaces of walls/ceilings and applying two coats of weather proof acrylic exterior paint (100% Acrylic) including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for 25 mm thick sand filling undder floors or in foundations uncluding watering and consolidation

M&L for preparation of primed steel surfaces exc 10 cm in width or girth and applying two coat of synthetic enamel paint all as specified.

S&F in repairs 25mm dia stainless steel pipe as in curtain rod including pair of decorative stainless steel brackets and knobs fixed to walls with screws as per sample approved by GE.

S&F two way CP fancy type bib tap of cat No. CON-041KN of Jaquar or equivalent as approved complete.

S&F in repair health faucet chromium plated with 8mm dia, 20 meter long flexible tube & wall hook, fixing to 15 mm bore of pipe all as specified and directed. Make :- Jaquar model No ALD - CHR-593 N or equivalent.

S&F in repair vitreous China urinal, half stall type, white fixed to wall including waste pipe including urinal spreader complete as specified complete.

S&F in repairs CP brass chromium plated towel rail 20 mm dia D type 600 mm long between the flanges.

S&F in repair plastic water closet seat black, closet pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device all as directed.

S&F in repairs PVC valveless 10 ltr capacity, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets.

S&F in repair Vitreous China wash basin under counter, white, flat back, size 480x370x200mm including brackets, waste coupling complete all as specified and as directed. Make:- Jaguar Cat No. CNS-WHT-701 or equivalent as approved make.

S&F CP single lever basin mixer with 450mm long braided holes Cat No. OPP-15011 BPM of Jaguar or equivalent complete.

M&L for 20 mm thick Granite slab machine cut and laid over cement screed and jointed with grey cement slurry and pointed with whiteor colour cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete including screed bed 20mm thick in CM 1:4.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations.

S&F in repairs sheet glass assembly consisting of 5 mm thick sheet glass shelf 12 cm wide with chromeum plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F repairs toilet paper roll holder, Make :- Jaquar Cat part No CAN-1151 N or equivalent.

S&F in repairs towel ring chromium plated. Make :- Jaquar Cat No CAN-1121 BN or equivalent

S&F PVC (SWR) multifloor trap plain with grating including jointing with solvent cement dia of out let 75 mm including stainless grating fixed complete all as specified and as directed.

S&F PVC (SWR) gully trap plain with grating including jointing with solvent cement dia of out let 125/110 mm including stainless grating fixed complete all as specified and as directed.

S&F PVC (SWR) bends of any radius 110 mm bore complete.

S&F in repair 110 mm dia PVC (SWR) junction single, (Single T) equal or unequal complete all as specified.

S&F PVC (SWR), vent cowl 110mm bore complete.

S&F PVC (SWR) bends 75 mm bore with or with out oval excess door complete all as specified and as directed.

M&L for PCC M-10 grade (Nominal mix) using 20mm graded stone aggregate as in foundation of manholes using extra cement all as specified.

M&L for PCC M-10 grade (Nominal mix) using 20mm graded stone aggregate as in bed to drain pipes incl paching under and haunching against the sides of pipes after they are laid and tested for 100mm bore all as specified.

M&L PCC M-15 grade (Nominal mix) using 20mm graded stone aggregate as in coping edging to interlocking tiles etc. complete all as specified and directed.

M&L PCC M-15 grade (Nominal mix) using 20mm graded stone aggregate as in cover slab complete all as specified and directed.

M&L for forming fair finished channel or drain 30cm ginth (inner ginth) in cement concrete using extra cement incl forms, moulds stopped complete.

M&L for rendering 15mm thick (10mm+5mm) in two coats in cement mortar 1:4, on fair faces of brick work or concrete surfaces, finished the surfaces even and fair mixed with integral water proofing compound @ 3% by total wt of cement or as per manufacture in finishing coat of 5mm thick complete, all as specified and directed. Note :- WPC shall be measured and paid separately.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints,hacking for key, scrubbing down with water, etc.

M&L for rendering 10 mm thick on other than fair faces of brick wall or concrete surface in cement mortar 1:3 finished even & fair all as specified and directed.

M&L for preparation of new plastered surface of walls and applying one coats of oil bound distemper over a coat of Alkali resistant primer complete all as specified and as directed.

M&L for preparing newly plastered surfaces of walls/ceilings and applying two coats of weather proof acrylic exterior paint (100% Acrylic) over one coat of self primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for complete removal of existing treatment of wall & preparation of old plastered surface of walls and applying two coats of oil bound distemper including preparation of surface of wall all as specified and directed.

M&L for prepration of old painted steel surfaces, exc 10 cm width or girth and applying one coats of synthetic enamel paint all as specified and as directed by Engineer-In-Charge.

M&L for prepration of old wooden surfaces, exc 10 cm width or girth and applying one coats of synthetic enamel paint all as specified and as directed by Engineer-In-Charge.

S&F powder coated (powder coating shall not be less than 50 micron of approved colour) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Powder coated (Minimum thickness of powder coating shall not be less than 50 micron of approved colour) aluminium window and ventilator shutters, side hung/ sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.)/ Pair of rollers at bottom of shutter, suitable handle (1 no.)/ Mortice type side locking arragement in shutter complete all as specified and as directed. Note : (i) Glass panes shall be measured & paid separately . (ii)The quoted rate shall be inclusive of cost of rubber beading however it shall not be weighed and shall not be paid separately. (iii) Unit rate is deemed including the cost of Peg stay, hinges locking arrangement etc.

S&F in repairs sheet glass assembly consisting of 5 mm thick sheet glass shelf tinted glass ordinary quality and glazing with oil putty in square n.exc 0.5sqmm in each pane complete.

M&L for 200mm aluminium barrel tower bolts of extruded section complete all as specified and directed.

S&F 100mm long hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21.

Taking up or down 15 mm bore of steel tubing and connections, including cleaning for refixing or removal to store complete all as specified.

Taking up or down 20 mm bore of steel tubing and connections, including cleaning for refixing or removal to store complete all as specified.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth of brick walls complete all as specified.

S&F in repair 15 mm size angular cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed both end for iron pipes complete.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm including brackets,waste coupling complete all as specified and as directed.

S&F in repairs sheet glass assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromeum plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F in repair swivel shower of PTMT any colour for fixing with 15mm dia shower rose complete.

S&F shower arm 15mm size, 195mm long with bend of 45degree with flange of PTMT any colour (min weight 40gms) complete.

S&F for brass chromium plated wall/sink mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

M&L for PCC M-10 grade (Nominal mix) using 12.5 mm graded stone aggregate louvres and jallies, 35mm thick (measured solid) including all mouldings set in CM 1:4 complete all as specified and directed.

M&L for rendering 20 mm thick on other than fair faces of brick wall or concrete surface in cement mortar 1:4 finished even & fair in two layers of 10mm thick each and forming V groovers in top layer complete all as specified and directed.

Forming V grooves in plaster 10mm deep and n.exc 10mm on face complete.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surface of slab, beam & ceiling surfaces finished even and fair all as specified and directed.

M&L for use & waste of steel form work (Rough finished flat) to side and soffits of floor or roof beams, lintels, contilevers sheves including supports etc.

M&L for use & waste of steel form work (Rough finished flat) to chajjas for rough finished surfaces complete all as specified.

M&L for rendering 10 mm thick on other than fair faces of brick wall or concrete surface in cement mortar 1:3 finished even & fair all as specified and directed.

M&L for preparation of RCC roof surfaces with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particels.Filling the cracks by crack filler providing PCC 1:3:6 at the places.Wherer slope is not proper of roof surface is uneven to maintain the proper roof slope. Providing 25 mm thick polymer modified plaster in ratio 1:10 (1 part of polymer and 10 parts of cement with solid contents not less than 30% over slab and applying priming coat of epoxy primer with resin and haerdener with water du\ilution as per manufacturer instructions,applying 1st coat if solvent based polyurethane liquid membrane not less than 500 micron thick UV stable having SRI value greater than equal to 105 with consumption of 0.61 kg/Sqm and applying 2nd coat solvent based polyurethane liquid membrane not less than 500 micron thick UV stable having SRI value greater than liquid to 105 with consumption of 0.61 kg/Sqm over dried 1st coat complete all as specified and directed. Make : Asian Paints/Pidilite/STP/Thermax/Sikka

S&F 35 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded fixed to wall with shop coat of red oxide primer complete all as specified and directed.

S&F IInd class hardwood, small fittings such as bracket of any size,hinge 1 blocks, cleats, door/window stoppers and like articles not exc 200cm each complete.

S&F 3mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 in each pane complete all as specified.

S&F Framed work such as grills gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

Surface excavation in soft/loose soil, not exceeding 30cm deep and averaging 10cm deep and getting out complete.

M&L for 15mm thick rendering in cement mortar (1:4) on fair faces of brick/concrete surfaces finished the surface even and smooth without using extra cement complete.

M&L for 100mm thick cement concrete M 7.5 grade (Nominal Mix) using 40mm graded stone aggregate as in sub base flooring complete.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade made with grey cement and pigment complete all as specified and directed.

M&L for PCC M-10 grade (Nominal mix) using 20mm graded stone aggregate in plinth course, string course etc complete all as specified and as directed by the Engineer-in-Charge

S&F in repairs 18mm thick Celuka ply of one side prelaminated and other side plain white colour to make kitchen cabinet/ drawer shutters complete as per specifications and as directed by the Engineer - in - charge.

S&F in repairs 18mm thick Celuka ply of one side prelaminated and other side plain white colour to make kitchen cabinet/ drawer shutters complete as per specifications and as directed by the Engineer - in - charge.

S&F in repairs 12mm thick Celuka ply of both side plain white colour fixed with screw, solvent cement/adhesive to make wall mount kitches cabinet back and pull out drawer sides complete as per specified and as directed by Engineer - in - charge.

S&F auto closing hinges 35mm of 0 crank (KH-001) OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters. Make:- KAFF, Godrej, Hettich

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kg. Make:- KAFF or equivalent approved make.

S&F magnetic catcher (KTS-20) full extension load capacity 8kg. Make:- KAFF complete.

S&F stainless steel handles 100mm size for kitches cabinet shutters complete.

S&F stainless steel 304 Gde kitchen modular basket for storage of plates, cups grain basket, glass cutlery, bottles, etc as per requied size all as specified and as directed.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles.

Material and labour for point wiring alongwith earth continuity conductor with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (phase- Red, Neutral - black, Earth- Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings/ fixing accessories after cutting chases for conduits and sunken GI pressed steel terminal boxes covered with 3 mm thick phenolic laminated top sheet cover white for mounting switches sockets, bell push, regulators etc and making good to walls, floors etc complete for the following:-

One light point controlled by one switch 6amp complete.

One exhaust fan point controlled by one switch.

One light point controlled by one switch 5amp complete.

One exhaust fan point controlled by one switch 5amp.

One 3 pin 5 Amp socket point controlled by one switch on same board.

One 3 pin 5 Amps socket point controlled by one switch on independent board.

All as per item No. 172 but for 3 pin / 5 pin 16 Amps sockets outlet with 4 Sqmm PVC insulated & unsheathed (FRLS) copper conductor cable independent complete all as specified and as directed .

Supply and Fixing ceiling rose surface bakelite 65mm x 50mm three terminals complete all as specified.

Supply and Fixing Modular switch 6 Amps single pole one-way, 1 Module complete all as specified.

Supply and fixing lamp holder polycarbonate body with back plate complete all as directed.

Supply & fixing indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light complete fitting 1x 20 watt LED Tube fitting with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Enginee-in-Charge. Make: - Havells, Cat Part No: LUMILINEBS20WLED 865 SPC WH or equivalent to CG/Bajaj/Philips

Supply & fixing indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light complete fitting 1x 9 watt LED Tube fitting mirror light with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Enginee-in-Charge. Make: - Havells, Cat Part No: LUMILINEBS9WLED 865 SPC WH or equivalent to CG/Bajaj/Philips

Supply and Fixing LED 7W lamp suitable for normal holder (Base Cap B22) complete all as specified.

S&F MCB distribution board, SPN 4 Way, double door, sheet steel, phosphatised, powder painted with Copper bus-bar 200Amp, neutral link, earth bar and din rail , cable ties for cable management, 240 V, complete all as specified.

Supply & fixing MCB SP 6 - 32 Amps, 'B' series, bracking cap10KA complete all as specified and directed.

Supply & fix MCB SPN 6-32 Amps, 'C' series, bracking cap10KA, 240V complete all as specified and directed.

Supply and fixing exhaust fan 300mm sweep heavy duty AC 230Volt single, 50Hz supply and including connecting up with twin core twisted flexible copper conductor cable of suitable size 0.75sqmm. Make:- Havells-Model Vential Air DB and equivalent of Bajaj/Crompton Greaves/Orient.

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and charcoal filling, necessary excavation and earth work complete.

Supplying, laying or fixing or passing through pipe, testing and commissioning XLPE insulated, steel tape/wire armoured heavy duty electric underground cable, 1100 volts grade with stranded aluminium conductor of 6sqmm 2core laid in trenches/duct/fixing on walls/poles or passing through pipe including connecting with suitable lugs, glands, nuts and bolts and testing incl connecting with suitable lugs, glands, nuts and bolts in existing panel from pole/Main Box and testing, incl dismantling of old unsv cable of size & type complete all as specified and directed.

All as per item No. 185 above but in PCC/floor/road complete.

M&L for HDPE double wall corrutaged pipe of size 40mm outer dia and 32mm inner dia confirming to IS: 14930 Part-Ii including necessary pipe fitting such as couplers, end caps, bend etc laid in trenches/fixed to wall with suitable clamps for cable protection complete all as specified and directed.

M&L for Sub Main Wiring for with two runs single core 4 Sqmm PVC insulated unsheathed (FRLS) cable with stranded copper conductor drawn in suitable size of rigid non-metallic PVC conduit and its all accessories complete concealed in wall/roof and including 4 Sqmm copper green colour earth wire incl cutting & chases( making good all to the disturbed surfaces as per existing) complete all as specified and directed by Engineer-in-Charge. Note :- Two run of 4 Sqmm single core cable, one run of 4 Sqmm earth wire & one run of PVC conduit will measured as one unit lenght.

Taking down aluminium/copper point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendent, regulators, sockets, flourescent tube light fittings etc, removing materials to store for keeping in safe custody or for taking credit and making good to the disturbed surfaces of walls, ceilings and floors etc complete all as directed.

Taking down carefully by Submain wiring/ service connection of any type complete all as directed by Engineer-in-Charge.

Supply and Fixing Modular switch 16 Amp single pole one way,2 Module all as specified.

Supply and Fixing Modular socket 2-in-1, 5 pins 6 Amps , combined 2 Module complete all as specified.

Supply and Fixing Modular socket 2-in-1, 5 pins 6/16 Amps , combined 2 Module complete all as specified. Make :- SSK/Anchor/Havells.

Supply and fix SP enclosure with a two pin and earth plug and socket complete with SP MCB of rating 10 Amps, 240 Volts complete with all conction as directed.

M&L for modular metal flush box, 1/2 module.

M&L for modular metal flush box, 3 module.

M&L for modular metal flush box, 6 module.

M&L for modular white cover plate with frame, 1/2 module.

M&L for modular white cover plate with frame, 3 module.

M&L for modular white cover plate with frame, 6module.

S&F environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head back-lit-LED luminaire comprising of high brightness lamp of 10watt complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of complete all as specified and as directed. Make:- Havells ordering cat Part No. HEXAFT10WLED 851SSY MBOPC or equivalent in Bajaj/Philips/Wipro/CG.

M/s Hoti Lal Contractor