Spl repair to certain B/R and E/M works bldg No T-35 of OR Md accn and upgradation of rewiring of bldg No T-1, T-5, T-7 and T-37 of Bana Singh Enclave at Tibri Mil Stn.

Amount

Material & labour Cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate as in roof padding finished even and smooth without using extra cement complete all as specified.

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) by forced application with butane torch over entire roof area/ sunken floor with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in, including bitumen primer @ 0.40 kg /Sqm after cleaning surface and applying evenly a tack coat of hot industrial bitumen 85/25 at the rate of 1.6 kg per sq.m including finishing with two coats of aluminium base paint for non accessible roof complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone agg) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

Demolition of cement concrete in ground floor & paving n.exc 15cm and above ground level any description

M&L for cement cocnrete type B-1 (1:2:4) (using 20mm graded stone aggregate) as in plinth protection thickness of 75mm.

Demolition of stone slabs, tiles of any description or thickness in floor, apron etc., laid bedded and pointed in any mortar complete all as directed.

M&L Non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.06 sqm to 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement to match including 15 mm thick screed bed in cm 1:6 complete all as specified and directed.

M& L Non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/ rectangular) area of each tile exceeding 0.06 sqm to 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement to match including 15 mm thick screed bed in cm 1:6 including demolition of existing tiles and screed complete all as specified and directed.

M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.18 sqm to 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement to match including 15 mm thick screed bed in CM 1:6 including demolition of existing tiles and screed complete all as specified.

M&L for ceramic glazed dark shade coloured tiles of size 350x250x 7mm/ 450x350x7mm thick joint free on and incl 10mm thick screed bed in CM(1:4)set and jointed in neat cement slurry and pointed in coloured cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/ dado including demolition of existing tiles and screed complete all as specified.

M&L for Green Marble work 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms, stair case and including 15 mm thick screed bed in CM 1:4 including pointing in white cement ( 1:2) using marble dust with admixture of pigment to match with marble shade including demolition of marble and screed complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as directed.

M&L plaster 15mm thick in cm 1:4 in sunken portion of slab with using waterproofing compound complete all as specified and directed. Note : WPC shall be measured and paid separately.

Supply only integral water proofing compound as per manufacturer instructions.

M&L for PCC 1:5:10 type E-2 using 40 mm graded stone agg in filling fdn and mass concrete in sunken floor.

M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base for receiving the floor finishes complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls, roof etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as directed.

M&L 15mm thick cement plastering in cm 1:6 on other than fair faces of brick surfaces , finished the surfaces even and smooth without using extra cement as spd

M&L 5mm thick cement plastering on ceiling in CM 1:3 on fair faces of brick, concrete surfaces , finished the surfaces even and smooth without using extra cement as spd

M&L 15mm thick cement plastering on fair faces of brick or concrete surfaces in cm 1:4 using water proofing compound Complete all as specified & directed. Note : WPC shall be measured and paid separately.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489-2004, Alkali & fungal resistance dirt resistance exterior paint of required shade company depot tinted with silicon additives @ 1.43ltre/10sqm over and including priming coat of exterior primer applied @ 0.90 ltre / 10sqm over new surfaces including preparation of surfaces.

M & L preparation of new plaster surface of ceiling and three coats of white wash complete all as specified & directed.

Preparation of new plastered surfaces and applying two coats of oil bound distemper (of approved shade) on walls over 1 mm thick wall care putty, on plastered surfaces complete all as specified.

M&L one coat of OBD on old decorated wall surface including preparation of surfaces complete all as specified and directed.

M&L for one coat of white wash on old treated ceiling surfaces including preparation of surfaces.

M&L for preparation of new wooden surface exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface exc. 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter from the chowkats) as spd

All as per Srl item No 28 above but exc 1.50sqm but n.exc 4.00 Sqm

Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm.

Supply and fix for pressed steel frames of size 105 mm x 60 mm for doors with one or more rebates including necessary lugs, hinges, lock strike plate including one shop coat of priming complete all as specified and as directed.

All as per Srl item No 31 above but of size 125mm x 60mm.

M&L for cement concrete type B0, 1:2:4 (12.5 mm graded aggregate) in filling of door and windows frames, any size, single or double rebated, including arrangement for fixing of hinges and fixtures as required.

S&F 30mm thick factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to e fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

S&F 35mm thick second class hard wood (Hollock), glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24(a) supplied and fitted to chowkats complete all as specified and directed.

S&F 35 mm Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F in repair 25 mm thick Prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination , fixed with screws to timber frame work for cupboard shutters complete all as specified and directed.

S&F in repair 18/19 mm Prelaminated particle board, interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work for partition and shelves of cupboards all as specified & directed.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanised, width of flaps (when open) 40 mm complete all as specified and directed.

S&F 150 mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified & directed.

S&F Aluminium anodized barrel tower bolt of extruded section 150mm long.

All as per Srl item No 42 above but 250mm long.

S&F aluminium alloy handle cast type anodized of size 100mm long.

All as per Srl item No 44 above but 150mm long.

S&F 300 mm long mild steel ordinary rat tail rod pattern spring, including roller and roller plate including fixing through welding/ bolts/ screws in metal/ wooden frame complete all as specified and directed.

S&F in repairs 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each complete all as specified and directed.

S&F 3mm thick figured glass pin head type, glazing with oil puty, in square n exe 0.5sq m in each pane complete all as specified and directed..

Taking down steel window/ ventilator (with shutter) any size.

S&F steel window box type made of ERW tube, hollow P section of size 60mmX25mm double rebated outer frame comprising double skeleton shutters i.e. guaged & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 including one shop coat of priming:- (i) Thickness of the sheet shall be of 18 gauge (ii) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (iii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iv) MS Tower bolt 150mm long-02 Nos per leaf (v) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (vi) Cleat 55mm long of hollow square 15mmX12mm -01 Nos per leaf (vii) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (viii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). Note: Wire cloth, glass, shall be measured and paid for separately

S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, including one shop coat of priming complete all as specified and directed. Notes: (i) Thickness of the sheet shall be of 18 gauge. (ii) Glass/ wire mesh, shall be measured and paid for separately

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks complete all as specified and directed.

Taking up and down GI pipe 15mm bore including fittings, connection complete all as specified and directed.

All as per Srl item No 54 above but 20mm bore of pipe.

S&F GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked complete all as specified and directed.

All as per Srl item No 56 above but fixing only (old serviceable pipe re-used including cleaning and new fittings).

S&F GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked complete all as specified and directed.

All as per Srl item No 58 above but fixing only (old serviceable pipe re-used including cleaning and new fittings).

Supply & fix 1000 ltr capacity rotational moulded polyethylene 3-layer water storage tank, white, ISI marked (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks complete all as specified and directed by Engr-in-Charge.

S&F in repair bib taps 15mm dia cast copper alloy chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule all as specified and directed.

S&F in repair for 15mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, fancy type, chromium plated with long shank and cup (concealed type)

S&F in repair for 15mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions.

S&F in repair stop valve 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screwed on both ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair brass CP shower rose 125mm size with swivel joint fancy type complete all as specified and directed.

S&F in repair 20 mm float ball brass valve high pressure with polythene float and flynut and connected fittings, screwed for iron pipe and fixed.

S&F CP brass towel rail 20mm dia. `D’ type 60 Cm long between flanges fixed to wall complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall or floor complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or floor complete all as specified.

Dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with PVC `P’ or `S’ trap, integral foot rest including connection to trap and flushing pipe, etc complete and bedding in PCC 1:7:12 type F-2 complete all as specified. Note:- Flush pipe and flushing cistern to be measured and paid separately.

S&F in repairs 08 to 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle and connections, joints to pipes, complete all as specified and as directed.

S&F in repair Flush pipe of polythylene of low or high density or PVC, 32mm dia for low level cistern.

S&F in repairs for vitreous china wash basin, white, size 630mm x 450mm flat back including brackets, brass CP waste coupling bore/ dia. of discharge pipe 32mm, cutting for and pinning in ends of bracket or errecting stand complete all as specified and as directed.

S&F in repair Pillar taps, cast copper alloy but fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe.

S&F in repair Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm- 45gms).

S&F in repair PVC waste pipe 32mm dia 600 to 750mm long fixed to wash fitting of wash basin/ urinal all as specified and directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600mm.

S&F in repair PVC (SWR ) bends 110 mm bore any radius.

S&F in repair PVC (SWR ) bends 75 mm bore any radius.

M&L in repair PVC (SWR ) floor trap 100/75 mm plain with grating incl. jointing with solvent cement.

S&F Stack clamps (for 100 mm pipe) out of 20 mm by 1.5 mm galvanised flat iron and stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

All as per Srl item No 83 above but 75 mm bore.

Demolition of brick work, built in cement mortar or cement lime mortar including all quoins, pillars etc. complete all as directed.

M&L for brick work with sub class 'B' old size bricks, straight or curved on plan exc. 6m mean radius built in CM 1:4 brick complete all as specified and directed.

S&F in repair cutrain rod 20mm dia of anodised aluminium alloy with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug complete all as specified and directed.

S&F in repairs stop valve 15mm dia cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends, fancy type chromium plated with long shank and cup concealed type all as specified and directed.

Excavating in trenches, n. exc. 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n. exc. 10 sq m on plan and n exc. 1.5m in depth, including taking out brick protection if any and getting out all as specified & directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm all as specified & directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified & directed.

Demolition and breaking up old unserviceable drain pipes (Salt glazed ware, AC or Reinforced concrete) 150 mm bore at any depth set in cement mortar including PCC bed complete all as specified & directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate in concrete bed to drain pipes 150mm bore including packing under,and haunching against the sides of pipes after they are laid and tested complete all as specified & directed.

Supplying, laying in trenches, jointing and testing Reinforced concrete pipes 150mm bore, class NP3, laid and jointed complete with collars at any depth over PCC bed complete laid in trenches and jointed as specified.

M&L for PCC 1:4:8 type D2 using 40 mm stone aggregate in filling, foundation of manholes complete all as specified and directed.

M&L Cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in coping, benching, apex stone, bed plate, kneelers including weathering, slightly rounded or chamfered angles complete all as specified.

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as cover slab for manholes and similar work etc including demolition of existing RCC complete all as specified.

M&L 60mm thick PCC (M-35) factory made machine pressed precast coloured interlocking tiles/ paver block of shape/ size as conforming to IS 15658, joints will be filled with fine sand complete all as specified and directed by Engineer-in-Charge.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base of floor finishing even & fair (for raising level) complete all as specified and directed.

M&L Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including, mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified & directed.

Taking down cement Plaster /deteriorated concrete from bottom of RCC chajjas /RCC facia /RCC beam/RCC slab/brickwork including racking out joints ,hacking for key ,scrubbing down with water (at a bldg height upto 4.50 m) and removing rubbish away and M & L for 15 mm thick plaster in CM 1:3 finished even and fair on bottom of RCC chajja & RCC facia complete all as specified and directed by Engineer -in-Charge

E/M PORTION Taking down carefully aluminium/copper point wiring for light, fan, bell, socket of point complete with fittings such as switches, ceiling roses, pendents, regulator, socket, light fittings etc complete at site and making goods disturbed surfaces of walls, floors to match with existing etc.

Point wiring with PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm including concealed PVC conduit with fittings and making good to the disturbed surfaces with continuous earth wire of PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm to common earth including provn of 3mm thick plastic laminated sheet of appropriate size and fixing to and including CI/MS boxes for mounting of accessories like surfaces sockets and regulators etc. complete all as specified for One light point/ Fan/ bell point controlled by one way switch

All as per Srl item No 104 above but one 5 pin socket outlet 5 amps on same board.

All as per Srl item No 104 above but 5 amps socket outlet on independent board.

All as per Srl item No 104 above but one light point controlled by two, two way switches.

All as per serial item No.104 here-in-before but with PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 2.5 Sqmm (nominal area), using approved colour coding, 1100 Volt grade ISI marked including PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 2.5 Sqmm (nominal area) 1100 Volt grade ISI marked as earth continuity conductor and connecting to the common earth dolly for 3 pin 15/16 Amps socket outlet on independent board.

M&L for sub main wiring with two single core multi stranded PVC insulated, unsheathed copper conductor of grade 1100 Volt , FRLS cable of size 6 sqmm (red for phase and black for neutral) and including electrical grade PVC conduit of desired colour not less than 1.2 mm thick and 25 mm dia. & 6 sqmm FRLS multistranded copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth duly complete and taking down old unserviceable one. Note :- (a) Cost of making good the disturbed surface plastering/ filling putty alongwith matching with the existing colour with distemper is deemed to be included in the quoted rate by contractor. (b) Three run of cable alongwith PVC conduit together shall be measured as single run.

S&F switch piano flush type single pole one way 5 amps.

S&F socket outlet 3 pin 5 amps flush type.

S&F switch flush type 15 amps single pole one way

S&F socket outlet 3 pin 15 amps flush type

S&F switch piano 2 way 5A all as specified and directed.

S&F in replacement surface mounting universal batten housing made of powder coated CRCA sheet suitable for upto 1 x 18/20 W LED tube and taking down existing old unserviceable housing complete all as specified and as directed.

S&F in replacement LED tube 20W ultra bright LED polycarbonate tube with very high efficacy suitable for fitting into tube light batten fitting complete all as specified and directed. Note :- The contractor will submit the LM-80 and LM-79 report form manufacturer to Engineer-in-Charge for approval before incorporating the items in work.

Taking down carefully ceiling fan complete fittings at site, removing fans, deposting to MES store yard and taking back to site for refixing complete all as specified and as directed.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose to connector of fan all as specified and directed.

S&F in replacement of fan regulator electronic type 5 step 100 watt, 240 volt and connecting complete all as specified and directed.

S&F bell, AC, 230 volts, single pole complete all as specified and directed.

S&F bell push flush type 6 Amp complete all as specified and directed.

Supply and fix for lamp holder PVC body angle type including 9 watt LED bulb, polycarbonate body with back plate complete all as specified and directed.

M&L ceiling rose, three terminal/ phase, PVC/ polycarbonate isolated body.

S&F GI pipe bracket made out of GI pipe light grade 32 mm bore and bent to shape 1.5m long, MS clamps made out of MS flat iron of size 40mm x 5mm thick and drilling of hole for and including nuts, bolts and washers including painting MS clamps with two coats of synthetic enemal paint over a coat of red oxide primer including taking down the existing GI pipe bracket complete all as specified and directed.

S&F in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including taking down existing fitting complete.

Supply and fixed in repair sheet metal enclosure for DB’s when MCB’s to be used, 240 volt 8 way SPN with bus bar and double door complete all as specified and directed. Note :- All the connection of incoming and out going wire in MCB will be made with thimble with suitable size as directed

S&F in repair MCB single pole 6 amps to 32 amps, complete all as specified and directed.

S&F in repair MCB single pole and neutral 32 amps complete all as specified and directed.

Material and labour for replacement of distribution board made out of CRCA sheet DB vertical type double door TPN 4 Way MS sheet including fixing in the wall, cutting chases, grounting and necessary patch work and white wash to match with the existing including making connections all as directed containing the folowings:- (a) MCCB 4 Pole 63 Amps 16 KA breaking capacity with thermal release: 01 No (In coming). (b) Bus bar made out of Aluminium duly insulated with adhesive tape RYB & black :4 Nos. (c) MCB SPN 40 Amp: 4 Nos, MCB SP 40 Amp: 04 Nos (Out going). (d) Connection from MCCB to bus bar will be made with Aluminium Strip of suitable capacity as directed.

M&L Earthing complete with galvanised steel earth plate electrode 60cm ×60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point including testing on completion including watering GI pipe 20mm bore medium grade, 15mm bore light grade GI pipe for protection of earth lead including provision of concrete pit in PCC (1:2:4) type B1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm including 8mm dia TMT bars both ways @ 15cm centre to centre with one handle for lifting made out of 8mm dia MS bar, funnel & wire mesh, excavation and earth work in any type of soil including testing, dismantling existing earthing complete all as specified & directed by Engr-in-charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core including taking out existing cable. Note: Excavation and earth work, sand cushioning, brick protection, GI pipe shall be measured and paid separately.

Supply and lay brick common burnt sub class "B" old size for protection of cable laid in trenches for under ground cable all as specified.

M&L sand cushioning in trenches using fine sand to under ground cable, laid in two layers complete all as specified.

A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

RATTAN CHAND CHANDAN AND CO

P S BUILDERS

talwinder singh and co

M/S DARSHAN & CO

AVTAR SINGH RAJU

J S MAAN ENTERPRISES