PROVN OF 02 X PARKING FOR AMBULANCE IN 182 MH AT MIL STN AGARTALA

Amount

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft/loose soil & removing the debris to out side MD land all as specified and directed.

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth for foundation and getting out in soft/loose soil complete all as specified and directed.

Material and labour broken stone or boulders hardcore of gauge n.exc 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as specified and directed.

Material and labour for cement concrete 1:4:8 type D-2 (using 40mm graded aggregate) as in foundations complete all as specified and directed.

Material and labour for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in CM 1:6 complete all as specified and directed.

Returning, filling in including spreading, levelling watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated soft/loose soil n.exc 50 mtr and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and directed.

Material and labour for formwork to sides of concrete foundations and plinth beams and similar work vertical or to batter for flat and rough finished surfaces complete all as specified and directed.

Material and labour formwork to side of pillars, posts, struts, piers, columns and stanchions for square, rectangular rough finished surfaces all as specified and directed.

Material and labour formwork to sides and soffits of floor or roof beams and lintels, cantilevers, overhangs etc for flat and rough finished surfaces all as specified and directed.

Material and labour for reinforced cement concrete (design mix) in M-25 (20mm graded aggregates) for foundation and plinth beams etc complete all as specified and directed.Note :- Reinforcement and form work required shall be measured Note :-(i) Reinforcement and form work required shall be measured and paid seperately (ii) Design mix will be approved by the CWE.

Material and labour for Reinforced cement concrete (design mix) in M-25, (20 mm graded aggregate) in columns/pillars complete all as specified and directed. Note :- (i) Reinforcement and form work required shall be measured and paid seperately (ii) Design mix will be approved by the CWE.

Material and labour for reinforced cement concrete (design mix) in M-25 (20mm graded aggregates) for beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. Note :- (i) Reinforcement and form work required shall be measured and paid seperately (ii) Design mix will be approved by the CWE.

Material and labour for TMT steel bars 10mm dia and over, cut to length,bent to shape required,including cranking bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips qualsecuring with clips all as specified and directed.

-ditto- all as per item No 14 above but 6mm to 10mm dia in stirrups complete all as specified and directed.

Material and labour for sand filling under floors or in foundations or as cable protection including watering and consolidation complete all as specified and directed. (Note: Compacted thickness / Punned thickness shall be measured for payment purpose)

Material and labour for 100 mm thick PCC 1:2:4 type B1 (Using 20 mm graded stone aggregate) as in floor, finished fair and even complete all as specified and directed.

Material and labour for construction joint 30 mm deep x 10 mm wide filled with sealing compound grade 'A' complete all as specified and directed.

Material and labour 75mm thick plain cement concrete type C 2, 1:3:6 (40mm graded stone agg) laid in panels including finished even and smooth using extra cement as in plinth protection including necessary formwork to edges and filling of joints with bitumminous sealing compound complete all as specified and as directed.

Material and labour PCC 1:3:6 type C2 using 40 mm graded aggregate as in surface channel/drain complete all as specified and directed.

Materials and labour for 15 mm thick rendering in CM (1:6) on other than fair faces of brick work or concrete surfaces on wall finished even and smooth without using extra cement complete all as specified and directed .

Materials and labour for 15 mm thick rendering in two layer, first layer shall be of 10 mm thick in CM 1:6 and second layer of finishing coat shall be 5 mm thick in CM 1:4 mixed with WPC @ 3% by weight of cement on fair faces of brick work or concrete surfaces on wall finished even and smooth without using extra cement complete all as specified and directed . (Note: WPC shall be measured and paid separately,)

Supply only integral water proofing compound

Materials and labour for preparation of new plastered or unplastered wall surfaces and applying three coats of white wash complete all as specified and directed.

Materials and labour for preparation of new plastered or unplastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistance primer complete all as specified and directed.

Supply and fixing steel work in tubular trusses i.e truss bottom, top bend, sides, side supports, holding plates, posts and base plate etc. including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 etc complete all as specified and as directed .

Supply and fixing Rolled steel hollow section square / rectangular as in purlins, rail etc complete using butt welded tubes confirming to IS 1161-1979 grade St-240 complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws as per manufactures instruction complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws as per manufactures instruction complete all as specified and as directed.

Supply and fixing hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Material and labour for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Material and labour for point wiring (surface type) for one light/fan/call bell point with 1.5 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade controlled by one way switch including 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC casing caping of suitable size with all accessories and PVC rectangular boxes for mounting switch, socket and fan regulator etc complete all as specified and as directed. Note: (i) Wiring shall be done in proper colour coding using red , yellow, blue for phase, black for neutral and green for earth. (ii) The cost of making good the disturbed surfaces is deemed to be included in the quoted rate.

Materials and labour for sub main wiring with two single core, FRLS, multi stranded, PVC insulated, 1100 Volt grade, cable with copper conductor of size 4 Sqmm in and drawing through existing surface / recessed steel/ PVC casing capping including continuous PVC insulated copper conductor single core earth contunuity conductor of size 4 Sqmm connected common earth complete all as specified and as directed. Note : (i) 3 Runs of 4 Sqmm cable and one run of conduit shall be measured as one unit length. (ii) The cost of making good the disturbed surfaces is deemed to be included in the quoted rate.

Supply & fixing switch piano flush type (ISI marked), single pole, one way 5 Amp, 240 Volts complete all as specified & directed.

Supply and fixing ceiling rose, PVC/polycarbonate, isolated body surface bakelite, 65mm x 50mm, ISI marked three terminals complete all as specified & directed.

Supply & Fixing MCB SPN having braking capacity 10 KA, 40 Amp, 240 Volt 'B' Curve complete all as specified and directed.

Supply and fixing MCB, single pole 'C' series having braking capacity 10 KA, 6 to 32 Amp, 240 volts, complete all as specified & directed.

Supply and fixing sheet metal enclosure for 8 way DBs single door type 240volts, 200 Amps rated bus bar including necessary connection all as specified and as directed. (Note: DB and MCB shall be of same Make.)

Supply & fixing IP >= 20, Class I, LED light fitting 1 x 20 W (4 FT), CRI >= 80, CT >= 5700 K, wall / surface mounted, integrated type with all accessories internally prewired and including connecting up with and including twin/three core twisted flexible copper conductor cable of suitable size in & incl flexible hose from ceiling rose to fitting complete all as specified and as directed. Make : Cat No ENDURALINEARNEOBS20WLED840SPCWH of Havells or equivalent make as mention in list of approved make in PS.

S&F energy saving high power LED building security light of 35W made up of pressure die cast aluminium housing with embedded PC cover having TOP opening seperate driver compartment with IP66 protection including GI pipe bracket made out of 40mm dia light grade pipe of length 1.2 Mtrs, bend to shape 120-130 degree and MS clamps made out of 25x3mm flat iron 2 Nos including nut and bolts for fixing the bracket and making connections in flexible conduit all as directed.

Materials and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire of 4mm dia by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 15mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion including taking down old unserviciable earthing set all as specified and as directed. Notes:- (i) Main earthing strip from earth plate electrode to rest point upto length of 7.5 meters length shall deemed to be included in the unit rate quoted against this item. (ii) On testing after completion if the desired resistenance is not obtained the contractor shall redo the earthing without any extra cost to the department.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 10 Sqmm nominal cross section in service connection 4 core complete all as specified and directed.

M/S PRITAM ENTERPRISES

M/S SANKAR GOPE

M/s Amrit Gope

M/S PAUL ENTERPRISE

Pranjit kar