CENTRALISED AC SYSTEM FOR SU-30 HOLDING STORES

Supply, Installation of the chillers including civil / structural supports for erection, Testing, commissioning and handing over of Air cooled chilled water plant of following capacities each comprising of :

a). Compact Semi Hermetic Twin Screw type Compressor

b).Air cooled Condenser with other accessories

c). Flooded/DX type shell and tube Chiller with accessories having entering/leaving conditions of water 12 Deg /7 Deg with maximum pressure drop .

d). Steel structure for assembling/mounting the equipment, finished with 1 coated primery paint & 2 coated painting, spring type vibration isolators for installing the equipment on foundation

e). Control panel incorporating all safety functions including HP & LP cutouts, single phase preventor, internal control wiring for sequential operation, contactors for sensing flow through leaving chilled water control, compressor & Electronic expansion valve modulation with automatic capacity/load limiting devices

f).Inter connected hard copper refrigerant piping with safety controls viz. Liquid line solenoid valves, HP/LP controls

g).Full charge of refrigerant R134a /410 and lubricant Oil

h).Unit mounted VFD starter panel comprising of disconnect switches, 3 Phase current Transformers and other essential compressor motor protecting devices

i). Unit mounted Dry expannsion technology with interlligent Micro Processor controller panel to achieve lower power consumption at part load and having menu driven digital display including operating datapoints for chilled water setpoint, leaving chilled water & condenser water temperatures, refrigerant pressure test condenser & Chillers, Heat control status, system operating schedule and current consumption data, remote operation ports etc.,

j).Insulation of shell & Tube chiller with Nitrile rubber

k). Nominal Capacity of 50-60TR Comination of 2 or 3 compressors.

Make: Bluestar / Carrier /Kehems/Clivet orequivalent.

Supply, Installation, Testing, Commissioning and handing over of Inbuilt Centrifugal vertical in line pump of following capacities with required head as per the following Primary water pumps including necessary Pressure Gauges with siphon & cock, insulation etc., complete

a). 140 US GPM @ 27 mt head and required rating motor along with Mechanical seal, drive transmission accessories and base frame e. (1W + 1S)

Make:Ebara/Xylem/Grundfos/Franklin

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al.cladding only exposed location as per specifications for the following:

size:125mm dia

Make: Tata / Jindal

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al.cladding only exposed location as per specifications for the following:

size:100mm dia

Make:Tata/Jindal

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al.cladding only exposed location as per specifications for the following:

size:80mm dia

Make: Tata/Jindal

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al.cladding only exposed location as per specifications for the following:

size:50mm dia

Make: Tata/Jindal

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al.cladding only exposed location as per specifications for the following:

size:32mm dia

Make: Tata/Jindal

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al.cladding only exposed location as per specifications for the following:

size:25mm dia

Make: Tata/Jindal

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al.cladding only exposed location as per specifications for the following:

size:20mm dia

Make: Tata/Jindal

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) Butterfly Valves/Ball Valves/NRVs

BUTTERFLY VALVE

Size: 80mm dia

Make: Honeywell / Zoloto

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) Balancing Valves.

size:80mm dia

Make:RB/ITEP/L&T/Zoloto/Hareyvell/Leader/Audco

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) BALL VALVE WITH SCREW END

size:50mm dia

Make: RB/ITEP/L&T/Zoloto/Hareyvell/Leeder/AUDCO

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) BALL VALVE WITH SCREW END

size:32mm dia

Make:RB/ITEP/L&T/Zoloto/Hareyvell/Leeder/Audco

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) BALL VALVE WITH SCREW END

size:25mm dia

Make:RB/ITEP/L&T/Zoloto/Hareyvell/Leeder/Audco

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) BALL VALVE WITH SCREW END

size:20mm dia

Make:RB/ITEP/L&T/Zoloto/Hareyvell/Leeder/Audco

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) Non Return Valves

size:80mm dia

Make:RB/ITEP/L&T/Zoloto/Hareyvell/Leeder/Audco

Accessories including supply and installation

Auto Air vent with Ball valve

Make: Honeywell / Zoloto

Accessories including supply and installation

Temperature Gauge

Make: H-Guru / Waree

Accessories including supply and installation

Pressure Gauge

Make: H-Guru / Waree

Accessories including supply and installation

Thermowell

Make: H-Guru / Waree

Y' Strainers including supply and installation

Size: 80mm dia

Make:Make: Advance / Sant/ Zoloto or equivalent.

Supply, installation, testing & commissioning of approved make Flexible connections (Rubber Bellows) at Chiller Outlet & Inlet pump suction, discharge side 32mm thick NItrile rubber insulation with 24G Aluminum cladding of fittings like valves, flanges and unions, etc. of chilled water syetm as per the approved shop drawings & specifications , 80 mm dia

Make: Resistoflex/cori/equivalent

Supply, installation, testing & commissioning of PIBC valve for AHU / CSU suteable as required standerds along with thremostart with control cable , compact to BMS aslo.

Supply installation & commissioning of Double skin Horigental Ceiling mounted AHU consisting of supply air damper, etc complete with all accessories for the following capacity - Sections: Pre Filter (10mic -50mm tk) , Coil and Fan secti Insulation 25mm tk RPUF, Panel¿s Inner 0.6 mm GI Plain and Outer Pre-painted 0.6 mm tk .Frame Aluminium extruded with nylon corners with Hollow Profile . Fan DIDW Forward curved AT Series make NICOTRA/ KRUGER/EQVT Motor : 3 PH - IE-2 -, MAKE - CG / ABB/ EQVT Cooling coil 1/2inch 6 Row CWC COIL. Aluminium finned copper tube with SS Drain pan, Filters 10mic HDPE media in GI Casing, with as per site condition sutable capacity .(24 TR/9600 CFM@55mm WG static pressure)

Make: Edgetech / SysytemAir / Vahyan/Equivalent

Supply installation & commissioning of Double skin Horigental Ceiling mounted AHU consisting of supply air damper, etc complete with all accessories for the following capacity - Sections: Pre Filter (10mic -50mm tk) , Coil and Fan secti Insulation 25mm tk RPUF, Panel¿s Inner 0.6 mm GI Plain and Outer Pre-painted 0.6 mm tk( Half White ).Frame Aluminium extruded with nylon corners with Hollow Profile . Fan DIDW Forward curved AT Series make NICOTRA/ KRUGER/EQVT Motor : 3 PH - IE-2 -, MAKE - CG / ABB/ EQVT Cooling coil 1/2inch 6 Row CWC COIL. Aluminium finned copper tube with SS Drain pan, Filters 10mic HDPE media in GI Casing, with as per site condition sutable capacity .(12 TR/4800 CFM@55mm WG static pressure)

Make: Edgetech / SysytemAir / Vahyan/Equivalent

Supply installation & commissioning of Double skin Horigental Ceiling mounted AHU consisting of supply air damper, etc complete with all accessories for the following capacity - Sections: Pre Filter (10mic -50mm tk) , Coil and Fan secti Insulation 25mm tk RPUF, Panel¿s Inner 0.6 mm GI Plain and Outer Pre-painted 0.6 mm tk Frame Aluminium extruded with nylon corners with Hollow Profile . Fan DIDW Forward curved AT Series make NICOTRA/ KRUGER/EQVT Motor : 3 PH - IE-2 -, MAKE - CG / ABB/ EQVT Cooling coil 1/2inch 6 Row CWC COIL. Aluminium finned copper tube with SS Drain pan, Filters 10mic HDPE media in GI Casing, with as per site condition sutable capacity .(10 TR/4000 CFM@55mm WG static pressure)

Make: Edgetech / SysytemAir / Vahyan/Equivalent

Pressure gauges with syphon and isolation valve etc complete.

Make: H guru / Bamur /wika/ Waree orequivalent.

Dial type Thermometers with ss thermowell etc complete set.

Make:Make: H guru / Bamur /wika/ Waree orequivalent.

Water flow switch with stem type sensing element probe for flow sensing.1 inch size.

Make: Make: H guru / Bamur /wika/ Waree/Hanewel orequivalent.

Air Separator of required size along with pressure rerlief valve, float, rashing rings and protective filter. & including pressurization pump set.

Make:Emerald / Anergy

ELECTRICAL Main Panel for the Plantroom with suitable incoming MCCBs & outgoings along with Star delta/DOL starters for 2Nos primary Pumps, 2 Nos chiller (1w + 1s).

ELECTRICAL starter Panel for the CSU / AHU with suitable incoming MCB with Star delta/DOL starters for each unit.

Supply, laying, testing and commissioning of 1.1kV Grade XLPE/PVC insulated Aluminium /copper multi-strands conductor steel of armoured power cables as per the specification.

Supplying and making End Termination with double compression glands for the following sizes of PVC / XLPE insulated PVC sheathed & armoured 1100 V grade cable including cost of crimping lugs compression glands, insulation tap etc. complete as required. Cpooer Armode 3.5 core X 95 Sq.MM with end termenation.

Make: Polycab / Finolex / KEI/RR/ or equivalent

Supply, laying, testing and commissioning of 1.1kV Grade XLPE/PVC insulated Aluminium/copper multi-strands conductor steel of armoured power cables as per the specification.

Supplying and making End Termination with double compression glands for the following sizes of PVC / XLPE insulated PVC sheathed & armoured 1100 V grade cable including cost of crimping lugs compression glands, insulation tap etc. complete as required. Cpooer Armode 3 core X 10Sq.MM with end termenation.

Make: Polycab / Finolex / KEI/RR/ or equivalent

Supply, laying, testing and commissioning of 1.1kV Grade XLPE/PVC insulated Aluminium/copper multi-strands conductor steel of armoured power cables as per the specification.

Supplying and making End Termination with double compression glands for the following sizes of PVC / XLPE insulated PVC sheathed & armoured 1100 V grade cable including cost of crimping lugs compression glands, insulation tap etc. complete as required. Cpooer Armode 3 core X 6 / 4 Sq.MM with end termenation which is sutable.

Make: Polycab / Finolex / KEI/RR/ or equivalent

CABLE TRAYS:

Supply, Installation of Cable tray shall be hot dipped galvanized and minimum thickness of GI coating is 90 to 100 Microns. Thickness of cable tray sheet steel for 50 mm to 300 mm cable tray 2.0 mm Thick Minimum height of the perforated cable Tray is 50 mm. Cable tray shall be in different widths and shall be in standard length 2500 mm long and suitable to couple two cable trays with coupler. up to 300mm Shall be Perforated.(including All required supports and Accessories.) 300X 50mm Size.

Make: ISI

Supply, Installation of Cable tray shall be hot dipped galvanized and minimum thickness of GI coating is 90 to 100 Microns. Thickness of cable tray sheet steel for 50 mm to 300 mm cable tray 2.0 mm Thick Minimum height of the perforated cable Tray is 50 mm. Cable tray shall be in different widths and shall be in standard length 2500 mm long and suitable to couple two cable trays with coupler. up to 300mm Shall be Perforated.(including All required supports and Accessories.) 200X 50mm Size.

Make: ISI

Supply, Installation of Cable tray shall be hot dipped galvanized and minimum thickness of GI coating is 90 to 100 Microns. Thickness of cable tray sheet steel for 50 mm to 300 mm cable tray 2.0 mm Thick Minimum height of the perforated cable Tray is 50 mm. Cable tray shall be in different widths and shall be in standard length 2500 mm long and suitable to couple two cable trays with coupler. up to 300mm Shall be Perforated.(including All required supports and Accessories.) 100X 50mm Size.

Make :ISI

DUCTING:

Supply, installation, balancing and commissioning of rectangular/round ducting complete with neoprene rubber gaskets, elbows, supports etc. of following sheet thickness complete as required. Thickness 0.59 mm sheet (24 gauge)

Make: Gpspira / Shama or equivalent.

DUCTING:

Supply, installation, balancing and commissioning of rectangular/round ducting complete with neoprene rubber gaskets, elbows, supports etc. of following sheet thickness complete as required. Thickness 0.80 mm sheet (22 gauge)

Make: Gpspira / Shama or equivalent.

DUCTING:

Supply, installation, balancing and commissioning of rectangular/round ducting complete with neoprene rubber gaskets, elbows, supports etc. of following sheet thickness complete as required. Thickness 1.00 mm sheet (20 gauge)

Make: Gpspira / Shama or equivalent.

DUCTING:

Internal duct acoustic insulation: - Supply, installation, testing and commissioning of internal duct acoustic insulation with open cell structured class "O" fire retardant nitrile rubber inside of the FCU/AHU supply air ducting of 15 mm thick

Make: Arma Flex / Aerofoam or equivalent.

DUCTING:

Thermal insulation :- Supplying and fixing of following thickness of mat finish closed cell nitrile rubber (class ¿1¿) insulation sheet on duct after applying two coats of cold setting adhesive complete of .25 mm thick.

Make: Arma Flex / Aerofoam or equivalen

DUCTING:

Canvas Piece :- Supply and erection of canvas connection (single layer cloth type ) between ceiling suspended fan coil units ( FCU) and duct.

Make: ISI

DUCTING:

Supplying, installing, testing & commissioning of high density Polyethelene (Sintex type) single piece water storage tank for make-up water shall be provided with necessary nipples and flanges, fabricated with GI/ CPVC pipes, all complete as per standard Detail. of 300 Ltr capacity.

Make: ISI

DUCTING:

Supplying & fixing of supply / Return Air Grill as required

Make: System air / Carriare / Airflow/Equivalent

DUCTING:

Supply, installation, testing and commissioning of volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as required

Make: System air / Carriare / Airflow/Equivalent

EARTHING:

Supply, installation Testing of earthing station as per IS standard complete 25x3mm GI strip / 8mmg wire as per site requirment.

Make:ISI

EARTHING:

SITC of Drain pipe with insulation Along with all fittings and clamps supports 32mm Dia with insulation.

Make: ISI

EARTHING:

Provision of M.S Structural Supports for Piping if any with MS Channels / Beams / Angles etc. painted with a coat of red oxide & 2 coats of enamel paint as required by the Client

Make:ISI

FOUNDATION WORK:

Includding Reinforcement, all necessary shuttering, material, labour etc. complete. Providing, laying , curing, etc for Foundation of Chiller & AHU.

Shed for Chiller & electrical panel & pumps. :

Supply of material & Installation Includding MS Column, all necessary fittings, material, labour etc. complete Shed of Chiller.

Total including GST

Contingency @ 10% and establishment charges @ 3% : 13%

Total including GST, contingency and establishment charges

HINDUSTAN AERONAUTICS LIMITED AVIONICS DIVISION, A Maharatna CPSE BALANAGAR, HAL POST, HYDERABAD 500 042, (TS) INDIA

TECHNICAL SERVICES DEPARTMENT

PRICE BID (Schedule-A)

TYPE OF CONTRACT: ITEM RATE CONTRACT

Name of the Work: Centralized AC System for SU-30 Holding Stores.

Tender Ref. No: HAL/HD/MT/CT/25-26/24

NAME OF THE BIDDER M/s:

Supply, Installation of the chillers including civil / structural supports for erection, Testing, commissioning and handing over of Air cooled chilled water plant of following capacities each comprising of : a) Compact Semi Hermetic Twin Screw type Compressor b).Air cooled Condenser with other accessories c). Flooded/DX type shell and tube Chiller with accessories having entering/leaving conditions of water 12 Deg /7 Deg with maximum pressure drop . d). Steel structure for assembling/mounting the equipment, finished with 1 coated primery paint & 2 coated painting, spring type vibration isolators for installing the equipment on foundation e). Control panel incorporating all safety functions including HP & LP cutouts, single phase preventor, internal control wiring for sequential operation, contactors for sensing flow through leaving chilled water control, compressor & Electronic expansion valve modulation with automatic capacity/load limiting devices f).Inter connected hard copper refrigerant piping with safety controls viz. Liquid line solenoid valves, HP/LP controls g).Full charge of refrigerant R134a /410 and lubricant Oil h).Unit mounted VFD starter panel comprising of disconnect switches, 3 Phase current Transformers and other essential compressor motor protecting devices i). Unit mounted Dry expannsion technology with interlligent Micro Processor controller panel to achieve lower power consumption at part load and having menu driven digital display including operating datapoints for chilled water setpoint, leaving chilled water & condenser water temperatures, refrigerant pressure test condenser & Chillers, Heat control status, system operating schedule and current consumption data, remote operation ports etc., j).Insulation of shell & Tube chiller with Nitrile rubber k). Nominal Capacity of 50-60TR Comination of 2 or 3 compressors. Make: Bluestar / Carrier /Kehems/Clivet orequivalent.

Supply, Installation, Testing, Commissioning and handing over of Inbuilt Centrifugal vertical in line pump of following capacities with required head as per the following Primary water pumps including necessary Pressure Gauges with siphon & cock, insulation etc., complete a) 140 US GPM @ 27 mt head and required rating motor along with Mechanical seal, drive transmission accessories and base frame e. (1W + 1S) Make:Ebara/Xylem/Grundfos/Franklin

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al. cladding only exposed location as per specifications for the following: size:125mm dia Make: Tata / Jindal

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al.cladding only exposed location as per specifications for the following: size:100mm dia Make:Tata/Jindal

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al.cladding only exposed location as per specifications for the following: size:80mm dia Make: Tata/Jindal

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al.cladding only exposed location as per specifications for the following: size:50mm dia Make: Tata/Jindal

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al.cladding only exposed location as per specifications for the following: size:32mm dia Make: Tata/Jindal

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al.cladding only exposed location as per specifications for the following: size:25mm dia Make: Tata/Jindal

Supply, erection, testing and commissioning of MS class 'C' class pipe with Thermal insulation, complete with civil / MS supports, fittings and pressure testing of pipes including M S supports, Insulation of piping shall be 32mm( 19+13 mm) thick nitrile rubber covered with 26 G Al.cladding only exposed location as per specifications for the following: size:20mm dia Make: Tata/Jindal

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) Butterfly Valves/Ball Valves/NRVs BUTTERFLY VALVE Size: 80mm dia Make: Honeywell / Zoloto

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) Balancing Valves. size:80mm dia Make:RB/ITEP/L&T/Zoloto/Hareyvell/Leader/Audco

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) BALL VALVE WITH SCREW END size:50mm dia Make: RB/ITEP/L&T/Zoloto/Hareyvell/Leeder/AUDCO

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) BALL VALVE WITH SCREW END size:32mm dia Make:RB/ITEP/L&T/Zoloto/Hareyvell/Leeder/Audco

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) BALL VALVE WITH SCREW END size:25mm dia Make:RB/ITEP/L&T/Zoloto/Hareyvell/Leeder/Audco

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) BALL VALVE WITH SCREW END size:20mm dia Make:RB/ITEP/L&T/Zoloto/Hareyvell/Leeder/Audco

Supply, fixing, testing and commissioning of the following valves PN 10 Rating including Valves to be insulated as per engineering standards thickness and specifications.(For Chilled water system) Non Return Valves size:80mm dia Make:RB/ITEP/L&T/Zoloto/Hareyvell/Leeder/Audco

Accessories including supply and installation. Auto Air vent with Ball valve Make: Honeywell / Zoloto

Accessories including supply and installation. Temperature Gauge Make: H-Guru / Waree

Accessories including supply and installation. Pressure Gauge Make: H-Guru / Waree

Accessories including supply and installation. Thermowell Make: H-Guru / Waree

Y' Strainers including supply and installation Size: 80mm dia Make: Advance / Sant/ Zoloto or equivalent.

Supply, installation, testing & commissioning of approved make Flexible connections (Rubber Bellows) at Chiller Outlet & Inlet pump suction, discharge side 32mm thick NItrile rubber insulation with 24G Aluminum cladding of fittings like valves, flanges and unions, etc. of chilled water syetm as per the approved shop drawings & specifications , 80 mm dia Make: Resistoflex/cori/equivalent

Supply, installation, testing & commissioning of PIBC valve for AHU / CSU suteable as required standerds along with thremostart with control cable , compact to BMS aslo.

Supply installation & commissioning of Double skin Horigental Ceiling mounted AHU consisting of supply air damper, etc complete with all accessories for the following capacity - Sections: Pre Filter (10mic -50mm tk) , Coil and Fan secti Insulation 25mm tk RPUF, Panel¿s Inner 0.6 mm GI Plain and Outer Pre-painted 0.6 mm tk .Frame Aluminium extruded with nylon corners with Hollow Profile . Fan DIDW Forward curved AT Series make NICOTRA/ KRUGER/EQVT Motor : 3 PH - IE-2 -, MAKE - CG / ABB/ EQVT Cooling coil 1/2inch 6 Row CWC COIL. Aluminium finned copper tube with SS Drain pan, Filters 10mic HDPE media in GI Casing, with as per site condition sutable capacity .(24 TR/9600 CFM@55mm WG static pressure) Make: Edgetech / SysytemAir / Vahyan/Equivalent

Supply installation & commissioning of Double skin Horigental Ceiling mounted AHU consisting of supply air damper, etc complete with all accessories for the following capacity - Sections: Pre Filter (10mic -50mm tk) , Coil and Fan secti Insulation 25mm tk RPUF, Panel¿s Inner 0.6 mm GI Plain and Outer Pre-painted 0.6 mm tk( Half White ).Frame Aluminium extruded with nylon corners with Hollow Profile . Fan DIDW Forward curved AT Series make NICOTRA/ KRUGER/EQVT Motor : 3 PH - IE-2 -, MAKE - CG / ABB/ EQVT Cooling coil 1/2inch 6 Row CWC COIL. Aluminium finned copper tube with SS Drain pan, Filters 10mic HDPE media in GI Casing, with as per site condition sutable capacity .(12 TR/4800 CFM@55mm WG static pressure) Make: Edgetech / SysytemAir / Vahyan/Equivalent

Supply installation & commissioning of Double skin Horigental Ceiling mounted AHU consisting of supply air damper, etc complete with all accessories for the following capacity - Sections: Pre Filter (10mic -50mm tk) , Coil and Fan secti Insulation 25mm tk RPUF, Panel¿s Inner 0.6 mm GI Plain and Outer Pre-painted 0.6 mm tk Frame Aluminium extruded with nylon corners with Hollow Profile . Fan DIDW Forward curved AT Series make NICOTRA/ KRUGER/EQVT Motor : 3 PH - IE-2 -, MAKE - CG / ABB/ EQVT Cooling coil 1/2inch 6 Row CWC COIL. Aluminium finned copper tube with SS Drain pan, Filters 10mic HDPE media in GI Casing, with as per site condition sutable capacity .(10 TR/4000 CFM@55mm WG static pressure) Make: Edgetech / SysytemAir / Vahyan/Equivalent

Pressure gauges with syphon and isolation valve etc complete. Make: H guru / Bamur /wika/ Waree orequivalent.

Dial type Thermometers with ss thermowell etc complete set. Make:Make: H guru / Bamur /wika/ Waree orequivalent.

Water flow switch with stem type sensing element probe for flow sensing.1 inch size. Make: H guru / Bamur /wika/ Waree/Hanewel orequivalent.

Air Separator of required size along with pressure rerlief valve, float, rashing rings and protective filter. & including pressurization pump set . Make:Emerald / Anergy

ELECTRICAL Main Panel for the Plantroom with suitable incoming MCCBs & outgoings along with Star delta/DOL starters for 2Nos primary Pumps, 2 Nos chiller (1w + 1s).

ELECTRICAL starter Panel for the CSU / AHU with suitable incoming MCB with Star delta/DOL starters for each unit.

Supply, laying, testing and commissioning of 1.1kV Grade XLPE/PVC insulated Aluminium /copper multi-strands conductor steel of armoured power cables as per the specification. Supplying and making End Termination with double compression glands for the following sizes of PVC / XLPE insulated PVC sheathed & armoured 1100 V grade cable including cost of crimping lugs compression glands, insulation tap etc. complete as required. Cpooer Armode 3.5 core X 95 Sq.MM with end termenation. Make: Polycab / Finolex / KEI/RR/ or equivalent

Supply, laying, testing and commissioning of 1.1kV Grade XLPE/PVC insulated Aluminium/copper multi-strands conductor steel of armoured power cables as per the specification. Supplying and making End Termination with double compression glands for the following sizes of PVC / XLPE insulated PVC sheathed & armoured 1100 V grade cable including cost of crimping lugs compression glands, insulation tap etc. complete as required. Cpooer Armode 3 core X 10Sq.MM with end termenation. Make: Polycab / Finolex / KEI/RR/ or equivalent

Supply, laying, testing and commissioning of 1.1kV Grade XLPE/PVC insulated Aluminium/copper multi-strands conductor steel of armoured power cables as per the specification. Supplying and making End Termination with double compression glands for the following sizes of PVC / XLPE insulated PVC sheathed & armoured 1100 V grade cable including cost of crimping lugs compression glands, insulation tap etc. complete as required. Cpooer Armode 3 core X 6 / 4 Sq.MM with end termenation which is sutable. Make: Polycab / Finolex / KEI/RR/ or equivalent

CABLE TRAYS : Supply, Installation of Cable tray shall be hot dipped galvanized and minimum thickness of GI coating is 90 to 100 Microns. Thickness of cable tray sheet steel for 50 mm to 300 mm cable tray 2.0 mm Thick Minimum height of the perforated cable Tray is 50 mm. Cable tray shall be in different widths and shall be in standard length 2500 mm long and suitable to couple two cable trays with coupler. up to 300mm Shall be Perforated.(including All required supports and Accessories.) 300X 50mm Size. Make: ISI

Supply, Installation of Cable tray shall be hot dipped galvanized and minimum thickness of GI coating is 90 to 100 Microns. Thickness of cable tray sheet steel for 50 mm to 300 mm cable tray 2.0 mm Thick Minimum height of the perforated cable Tray is 50 mm. Cable tray shall be in different widths and shall be in standard length 2500 mm long and suitable to couple two cable trays with coupler. up to 300mm Shall be Perforated.(including All required supports and Accessories.) 200X 50mm Size. Make: ISI

Supply, Installation of Cable tray shall be hot dipped galvanized and minimum thickness of GI coating is 90 to 100 Microns. Thickness of cable tray sheet steel for 50 mm to 300 mm cable tray 2.0 mm Thick Minimum height of the perforated cable Tray is 50 mm. Cable tray shall be in different widths and shall be in standard length 2500 mm long and suitable to couple two cable trays with coupler. up to 300mm Shall be Perforated.(including All required supports and Accessories.) 100X 50mm Size. Make :ISI

DUCTING: Supply, installation, balancing and commissioning of rectangular/round ducting complete with neoprene rubber gaskets, elbows, supports etc. of following sheet thickness complete as required. Thickness 0.59 mm sheet (24 gauge). Make: Gpspira / Shama or equivalent.

DUCTING:Supply, installation, balancing and commissioning of rectangular/round ducting complete with neoprene rubber gaskets, elbows, supports etc. of following sheet thickness complete as required. Thickness 0.80 mm sheet (22 gauge). Make: Gpspira / Shama or equivalent.

DUCTING: Supply, installation, balancing and commissioning of rectangular/round ducting complete with neoprene rubber gaskets, elbows, supports etc. of following sheet thickness complete as required. Thickness 1.00 mm sheet (20 gauge). Make: Gpspira / Shama or equivalent.

DUCTING:Internal duct acoustic insulation: - Supply, installation, testing and commissioning of internal duct acoustic insulation with open cell structured class "O" fire retardant nitrile rubber inside of the FCU/AHU supply air ducting of 15 mm thick. Make: Arma Flex / Aerofoam or equivalent.

DUCTING: Thermal insulation :- Supplying and fixing of following thickness of mat finish closed cell nitrile rubber (class ¿1¿) insulation sheet on duct after applying two coats of cold setting adhesive complete of .25 mm thick. Make: Arma Flex / Aerofoam or equivalen

DUCTING: Canvas Piece :- Supply and erection of canvas connection (single layer cloth type ) between ceiling suspended fan coil units ( FCU) and duct. Make: ISI

DUCTING: Supplying, installing, testing & commissioning of high density Polyethelene (Sintex type) single piece water storage tank for make-up water shall be provided with necessary nipples and flanges, fabricated with GI/ CPVC pipes, all complete as per standard Detail. of 300 Ltr capacity. Make: ISI

DUCTING:Supplying & fixing of supply / Return Air Grill as required Make: System air / Carriare / Airflow/Equivalent

DUCTING:Supply, installation, testing and commissioning of volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as required. Make: System air / Carriare / Airflow/Equivalent

EARTHING:Supply, installation Testing of earthing station as per IS standard complete 25x3mm GI strip / 8mmg wire as per site requirment. Make:ISI

EARTHING:SITC of Drain pipe with insulation Along with all fittings and clamps supports 32mm Dia with insulation. Make: ISI

EARTHING:Provision of M.S Structural Supports for Piping if any with MS Channels / Beams / Angles etc. painted with a coat of red oxide & 2 coats of enamel paint as required by the Client Make: ISI

FOUNDATION WORK: Includding Reinforcement, all necessary shuttering, material, labour etc. complete. Providing, laying , curing, etc for Foundation of Chiller & AHU.

Shed for Chiller & electrical panel & pumps. : Supply of material & Installation Includding MS Column, all necessary fittings, material, labour etc. complete Shed of Chiller.

Grand Total Amonunt including GST in figures in Rs.

Grand Total Amonunt including GST in Words.

SAC CODE

The tenderers are requested to read the following before quoting:

Sucessful offer that is L-1 (Lowest offer) will be determined including GST.

The payment terms shall be governed as per the terms indicated in General conditions of contract.

Amount towards GST will be paid along with RAR payment against invoice.

The tenderers are requested to abide by the rules of prevailing GST act.

This BOQ specification has to be read in conjunction with technical specifications and tender drawings if any. Any ambiguty in these have to be brought to the knowledge of contract section before submission of tender to avoid future claims/dispute.

b) In order to get the access of work, vendor has to visit the site before participating in the

tender and give an undertaking that they have understood the scope of work in detail. The

undertaking to be counter signed by the user department. The same undertaking must be

submitted in the technical document to qualify for the tender.

C) Chiller ,AHUs need to be inspected at vendors site before dispatch to ensure the quality and

performance of units before installation at site .

HINDUSTAN AERONAUTICS LIMITED

AVIONICS DIVISION::HYDERABAD

Pre-Qualification Profile

Estimated Amount in Rs.

Tender Notice Date:(DD-MM-YYYY)

Last date for submission of tender (DD-MM-YYYY)

Completion Period (In Months)

Name of the Individual / Firm / Company: * (Mandatory)

Type of ownership / Legal Status [Attach copies of the original document defining the legal status]

Year of Establishment of Company/Business

Registered Office Address, Telegraphic Address, Telephone No., Website / email id, FAX No.

Correspondance Address, Telegraphic Address, Telephone No., Website / email id, FAX No.

PAN no

PF number (If any)

ESI number

GST registration number

Particulars of registration with various Government bodies (Attach documentary proof)

a) Registration Number/s

b) Organization / Place of registration

c) Category [Limit for tendering]

Contact details

Contact person name

Designation

Mobile No.

Ph. No. with STD code

FAX No. with STD code

Email Id :

I.T Returns for past 03 years

Assessment year 2023-24 (i.e FY 2022-23)

Assessment year 2024-25 (i.e FY 2023-24)

Assessment year 2025-26 (i.e FY 2024-25)

Maximum value of works executed during the following 05 years and it should be certified by Chartered Accountant. (In Rs. Lakhs)

Turn over Criteria is Not met

DETAIL OF WORK ON HAND UPTO COMPLETION PERIOD OF SUBJECT WORK [Required for Bid capacity calculation] .Details are also to be furnished on Proforma-D

Sl.No(work No)

Bid Capacity

Action plan / bar chart as to indicate the completion of work, within the scheduled time (contract period)]

Bank(s) details: [Copy of the cheque leaf to be uploaded]

Bank Statement for past THREE months

Latest Over draft Facilities with Bankers

Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued NOT before 12 months from the final date of submission of Tender.

Required solvency value in Rs.

Name of Bank & Branch

Date of Issue (dd/mm/yyyy)

Value Rs.

Solvency value is NOT as per NIT

Experience of having successfully completed similar works during last 7 years ending on the previous day of submission of tender should be either of the following:. [ Work completion certificates along with LOA/PO/WO should be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated amount put to tender. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated amount put to tender. (iii) ONE similar completed work costing not less than the amount equal to 80% of the estimated amount put to tender.

Completed similar works during last 7 years

Work No I

Name of The organisation

Brief Description of Work:

Completed value of Work in Rs.

Date of Commencement of Work [DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

Work No II

Name of The organisation

Brief Description of Work:

Completed value of Work in Rs.

Date of Commencement of Work [DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

Work No III

Name of The organisation

Brief Description of Work:

Completed value of Work in Rs.

Date of Commencement of Work [DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

DETAILS OF TECHNICAL PERSONNEL AVAILABLE( if space provided is insufficient separate sheet to be uploaded with the same format as below)

PLANT, MACHINERY AND EQUIPMENT AVAILABLE [The Plant, Machinery and equipment (either owned or leased) that can be made available for this work must be furnished below].

Works of similar nature successfully completed in addition to Sl. No. (21) of Applicant Particulars (1) during the last 07 years ending last day for previous month.

Sl.No. (work No.)

Details of person holding the power of Attorney

Position

Mobile No.

Ph. No. with STD code

FAX No. with STD code/ e-mail ID

DECLARATION I

I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer . 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I//We are aware that document sought only be uploaded for evaluation of offer. 5. I/We shall not associate nor has been associated in the past, directly or indirectly with consultant or any other entity that would prepare the design, specification and other documents of the project.

DECLARATION II

I/We declare and undertake that - 1. To provide all facilities to HAL, Bangalore for verification of the information / details furnished by us and also for inspection of our works carried out / in progress if required. 2. The bid does not contain any amendment, modification as change of any type whatsoever in the bid documents and to any amendment issued thereafter.

EMD details

Description