Construction Of Dayat Faliya School, Silvassa

Amount

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 Meter lead.(A) Loose or soft soil

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 Meter lead.(A) Loose or soft soil

Boring holes 3.5 m deep in ordinary soil (for cast in situ piles) and getting out the soil and disposal of the surplus excavated soil as directed within a lead of 50 Meter for following diameter of pipes.(iii) 300 mm

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each disposited layer by ramming and watering etc. complete as directed by EIC

Excavating, Supplying , stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20cm in foundation trenches, plinth ,sides of foundation etc. complete for all lift.

Filling in plinth with sand under floors including watering ramming, consolidating and dressing complete as directed by EIC

Carring out plinth treatment to post construction / existing structure by spraying chemical solution for termite control treatment including labour and material consistment with I.S.I specification. Using Chlordene and Chiorpurfiles 20 EC. As Per 6131_paret-II Consentration Weight one percent is recommended i.e one litre 20 EC chemical emulsion with 19 liter give 1 % concrentration inclusive of one litre chemical emulsion appication at the rate of 5 Litre chemical / Sqm of surface is recommended as per I.S

Providing and laying rubble soling, 230 mm thick, in a compact manner,foudation, road, footpath etc. using 200 to 230 mm. cut size stones including filling the gaps with 40mm metal and packing with stone chips with murrum covering and levelling the surface after filling the voids including watering, ramming well and consolidating each layer, as directed by EIC.

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4- graded stone aggregates 20 mm nominal size) and curing complete excluding cost of formwork in (A) Foundation and Plinth

Providing and laying in position Ready Mixed M-300 grade concrete for reinforced cement conctere work , using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash(Min cement level as per latest IS 456 shall be maintained) (Cement level 475 kg )

Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level

Providing and applying anticarrasive treatment with polymer base materials to the steel reinforcement including descaling the dust and applying the preventive coating of approved Make etc.complete

Extra for additional lift of reinforcing steel for all R.C.C. work above floor two level upto floor four level.

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish including steel prop (A) Foundations, Footings, Bases of Columns etc. and Mass concrete

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish including steel prop (B)Floors etc.Upto 200mm in thickness

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish including steel prop(G)Columns,Pillars,Posts and struts(1)Squre,Rectangular or polygonal in plan

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish in (G) Columns, Pillars, Posts and struts. (2) Circular or curved in plan

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish including steel prop(H)(1) Lintel Beam Formwork

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish including steel prop (H)(2)Sides and soffits of Beams,Beam Haunchings cantilevers Griders,Bressumers And Lintels not exceeding 1 M.in Depth.

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish including steel prop (L)Chullah Hoods weather Shades Chajjas Corbels etc.and the like

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish including steel prop (M) Staircase with sloping or stepped soffits including risers and stringers excluding landing.

Providing and laying Autoclaved Aerated Concrte (AAC) blocks masonry with 150mm to 300mm. Thick with Grade-1 AAC blocks of density 551 to 650 kg./cum conforming to IS:2185(part3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-charge. ( AAC Should be Sand base )(Without GST) 1)Plinth Level

Providing and laying Autoclaved Aerated Concrte (AAC) blocks masonry with 150mm to 300mm. Thick with Grade-1 AAC blocks of density 551 to 650 kg./cum conforming to IS:2185(part3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-charge. ( AAC Should be Sand base )(Without GST) 2)Ground Floor

Providing and laying Autoclaved Aerated Concrte (AAC) blocks masonry with 150mm to 300mm. Thick with Grade-1 AAC blocks of density 551 to 650 kg./cum conforming to IS:2185(part3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-charge. ( AAC Should be Sand base ) (Without GST) 3)First Floor

Providing and laying Autoclaved Aerated Concrte (AAC) blocks masonry with 150mm to 300mm. Thick with Grade-1 AAC blocks of density 551 to 650 kg./cum conforming to IS:2185(part3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-charge. ( AAC Should be Sand base ) (Without GST) 4)Second Floor

Providing and laying Autoclaved Aerated Concrte (AAC) blocks masonry with 150mm to 300mm. Thick with Grade-1 AAC blocks of density 551 to 650 kg./cum conforming to IS:2185(part3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-charge. ( AAC Should be Sand base ) (Without GST) 5)Third Floor

Providing and laying Autoclaved Aerated Concrte (AAC) blocks masonry with 150mm to 300mm. Thick with Grade-1 AAC blocks of density 551 to 650 kg./cum conforming to IS:2185(part3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-charge. ( AAC Should be Sand base ) (Without GST) 4)Terrace Floor

Providing and laying Half brick masonry in common burnt clay building bricks having crushing strength note less than 35 Kg/Sq. Cm. in cement mortar 1:4 (1 cement : 4 coarse sand) in super structure above plinth level at any floor level.(B) Conventional. 1) Ground Fl.

Providing and laying Half brick masonry in common burnt clay building bricks having crushing strength note less than 35 Kg/Sq. Cm. in cement mortar 1:4 (1 cement : 4 coarse sand) in super structure above plinth level at any floor level.(B) Conventional. 2)First Floor

Providing and laying Half brick masonry in common burnt clay building bricks having crushing strength note less than 35 Kg/Sq. Cm. in cement mortar 1:4 (1 cement : 4 coarse sand) in super structure above plinth level at any floor level.(B) Conventional. 3)Second Floor

Providing and laying Half brick masonry in common burnt clay building bricks having crushing strength note less than 35 Kg/Sq. Cm. in cement mortar 1:4 (1 cement : 4 coarse sand) in super structure above plinth level at any floor level.(B) Conventional. 4)Third Floor

Providing & laying10 mm. thick cement plaster in single coat on fair side of brick concrete walls & ceilings for interior plastering upto floor two level and finishing with smooth mala plaster.(i) Cement mortar 1:3 (1 cement : 3 sand) 1) Ground Floor

Providing & laying10 mm. thick cement plaster in single coat on fair side of brick concrete walls & ceilings for interior plastering upto floor two level and finishing with smooth mala plaster.(i) Cement mortar 1:3 (1 cement : 3 sand) 2) First Floor

Providing & laying10 mm. thick cement plaster in single coat on fair side of brick concrete walls & ceilings for interior plastering upto floor two level and finishing with smooth mala plaster.(i) Cement mortar 1:3 (1 cement : 3 sand) 3)Second Floor

Providing & laying10 mm. thick cement plaster in single coat on fair side of brick concrete walls & ceilings for interior plastering upto floor two level and finishing with smooth mala plaster.(i) Cement mortar 1:3 (1 cement : 3 sand) 4)Third Floor

Providing & laying10 mm. thick cement plaster in single coat on fair side of brick concrete walls & ceilings for interior plastering upto floor two level and finishing with smooth mala plaster.(i) Cement mortar 1:3 (1 cement : 3 sand) 5) Terrace Floor

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick walls for interior plastering upto floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4sand) Ground Floor

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick walls for interior plastering upto floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4sand) First Floor

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick walls for interior plastering upto floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4sand) Second Floor

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick walls for interior plastering upto floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4sand) Third Floor

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick walls for interior plastering upto floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4sand) Terrace Floor

Providing 20 mm thick double coat mala cement plaster on interior brick / concrete work for plastering comprising of base coat of 12 mm thick cement plaster in cement mortar (1 Cement : 4 coarse sand) in rough finishing and 8 mm thick top coat of cement mortar 1:2 (1 Cement : 2 Coarse sand) finished with trovel including scaffolding curing etc. complete.

20mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete.

Providing and laying 20 mm thick water proof cement plaster using water proofing powder 1Kg/1bag of cement for all floors on brick / concrete wall work using water proofing materials in C M 1: 4 ( 1 cement 4 coasrse sand) including finishing with a flooting coat of neat cement slurry etc complete for all floor. and shall be guaranteed for minimum period of 10 years after handing over the completed building by the main contractor to be finished as directed. Stamp paper guarantee 10 years to be furnished before receiving any payment from the client.

Applying two coats of putty & two coats of primer of approved brand and manufacture on new wall surface to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth.

Wall painting (three coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth. For Ceiling

Wall painting (three coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth. For Wall

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials etc. complete

Providing and fixing flush door both sides laminated and I.T.W. beading all around by using I.T.W. frame 120 m.m. x 80m.m.. shutter fabricated from 35 mm thick solid core malemine faced three layered pre laminated flat pressed wood based exterior grade bonded BWP/BWR synthetic resin having stamped IS 12823 grade I type II including three coats of lacquer polishing to exposed wooden surfaces and Stainless steel decorative type designs fixtures / fastening 2Nos. Handle, 2Nos. Aldrops, towerbolt, hinges etc.including I.T.W. triangular batten patti of size 30m.m.x30m.m.etc. as per architectural detailed drawing and as directed by engineer in charge.

Providing and Fixing,premium quality French uPVC factory made,Colour sliding Three track window of Fenesta make, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of Mosquito net & hardware, EPDM gasket, 1.2 ± 0.2mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in-charge. The Rates inclusive of 5 mm Glazing and mouskito net with hardware hinges and fitting etc.

Providing and Fixing,premium quality French uPVC factory made,Coloured Adjustable louvers with box frame of Fenesta make, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in-charge. The Rates inclusive of 3 mm thick bajari glass, hardware hinges and fitting etc.

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. (A) 25mm thick - Polished Green Kota (1200 x 600)

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. (A) 25mm thick - Polished Mirror Kota (1200 x 600)

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. (A) 25mm thick - Leather Finished Green Kota (600 x 600)

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. (A) 25mm thick - Leather Finished Golden Kota (600 x 600)

Providing and laying polished kota stone tiles10mm thick in risers of steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with gray cement slury mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. A) Polished Green Kota (1200 mm /600 mm length)

Providing and laying polished kota stone tiles10mm thick in risers of steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with gray cement slury mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. A) Polished Mirror Kota (600 mm length)

Providing and laying polished kota stone tiles10mm thick in risers of steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with gray cement slury mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. A) Leather Finished Golden Kota (600 mm length)

Providing and laying polished kota stone tiles10mm thick in risers of steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with gray cement slury mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. A) Polished Golden Kota (600 x 600)

Providing and fixing Pre-galvanised grill of required pattern for windows etc. with precoated galvanised flats at required spacing and frame alround square or round headed bolts and nuts or by screws.including applying a priming coat of red lead paint and two coats of oil painting etc complete (A)Plain grill

Providing and laying 18mm thick Kota Stone of specified size, even thickness, colour, shade and of approved make, cladding , sill and jambs of door, window & ventilation frame with mini. two coat of construction chemical and as per manufacture specification incl. rubbing and polishing, rounding edge and All joints filled with coloured cement putty as per architect detail and wiped to give sharp joints with flush pointing and washed clean with acid As per drawings and design supplied by architect and instruction given by authority and E.I.C.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. “All above operations to be done in order and as directed and specified by the Engineer-in-Charge”: With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing & laying broken china mosaic flooring on top of integral waterproofing using small broken chips of white/colour glazed tiles set in crazy pattern, as desired by Architect, in cement mortar laid to required slopes and simultaneously filling in remaining top joints in the waterproofing layer and tamped with wooden block to get smooth even surface to required slope, filling the joints with cement grout , cleaning the surface on completion and curing etc. complete. The work sall be carried out in a workman like manner to make the give a guarantee on stamp paper for the performance for a period of ten years.The work shall be measured in square meter of the actual area laid and no extra shall be paid for vatahs, rounding at junction of wall and floor and around water spouts, water outlets etc.

Providing cement vata (10cm. x 10 cm. size) quarter round in cement mortar 1:1 including neat cement finishing, watering etc. complete.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing Laying and Fixing 18 mm thick Granite couter or platform with cutting and laying size of under counter wash basin or sink with building commercial marble structure as needed with 150mm groove in the wall for fitting. Laying Granite stone with moulding on all edges to 10-25mm moulding with applicable tile adhesive for fixining including of fitting and joining with 45dgree cutting edges between 2 perpendiclular stone. mirrior polishing on all the exposed surface. structure of kotah stone or marble for vertical partition at regular interval for storage drawer. finishing with white cement including polishing on bothsides,finishing edges with round shape of stone etc. complete.

Providing and fixing 1200mm x 750mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.

Pro. And fixing single layer water proof gypsum board 12.5 mm thick sections using water proof board of size 1220 mm x 1830 mm x 8.0 mm suspended by GI suspender channel of size 25 mm x 3 mm with intermediate channel of size 18 mm x 40 mm x 0.8 mm at 1220 mm center to center ceiling section of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c and perimeter channel A of size 20 mm x 27 mm x 30 mm x 0.5 mm at edges & drops incl. paper tap sand soffit cleat, anchor fastener, scoch bolt connecting cleat, joining compound top coat on ceiling incl. making necessary opening for light fitting, diffuser etc. comp. as per detail drawing as directed

Providing and Fixing 10 mm thick multiwall polycarbonate roofing sheet lexan /bayer UV resistant fixed with hilti screw and rubber silicon sealer and alluminium strip of size 50 mm x 3 mm etc complete As per drawings and design supplied by architect and instruction given by authority and E.I.C.

Providing and Fixing Steelwork required to be galvanised shall be pickled in dilute hydrochloric acid, washed, fluxed and stoved, and then coated with zinc by dipping a bath of molten zlnc. Components shall be immersed ln the bath only For the period sufficient to attaJn the temperature of the bath and shall be withdrawn at a speed which ensures that a coating of 610 grams per square metre of surface is achieved - i.e. 85 mlcrons minlmum Dry Film Thlckness (OFT). Components shall be covered evenly on all surfaces. Items shall not be galvanised in more than one dip event due to potential warping or additional stresses that may be induced in the metal. Items described as heavily galvanised shall be grit or sand blasted prior to galvanising and shall receive a minimum coating of 1000 grams per square metre of surface - le, 140 microns minimum OFT. Galvanised steelwork shall be cleaned, degreased and etch primed including painting as required by EIC.

Providing throating of plaster drip and moulding to R.C.C. Chhajja.

Providing and fixing pre-cast Rubber moulded inter locking concrete block 80mm thick with grade of concrete M40 pnumatic compressed by mechanically pressed and as per approved design including 75mm sand layer for levelling and filling the joint with sand in proper line and level etc. complete and including cost of carting of debrises in out side of premises with all lead & lift as directed by engineer in charge.

Constructing Under Ground water tank with Providing and laying controlled cement concrete M250 mix for R.C.C. work including reinforcement, boxing, centering, vibrating, curing and mixed with approved water proofing cement compound or "CEMWET" or "PIDICRETE LW" integral water proofing admixture as water proofing agent to be mixed with 50 kgs. bags shall be as recommended by the manufacture of the water proofing material, concrete work for top, bottom slab & side pardi,column, beam for under ground water tank item incl. Necessary excavation & refilling the available earth, 15 cm thk 1:2:4 for bedding of concrete, 20 mm thk. water proofing cement plaster in C.M. 1:3 with smooth finishing & Glazes tile Dedo, vata,50mm thick cement concrete flooring watering etc. Comp. to all face of tank . including locking arrengement outlet, inlet, overflow and washout outlet pipe arrengement as necessary & C.I. Cover 0.60 x 0.45 weight not less then 35 kg with locking arrengment.C.I. steps etc. comp as per structural detail drawing Including thermo Mechanically treated bars (TMT BARS) Fe 500/500D as directed by Eng-in-charge.

Constructing RCC Overhead water tank with Providing and laying controlled cement concrete M250 mix for R.C.C. work including reinforcement, boxing, centering, vibrating, , PVC water stopper, curing and mixed with approved water proofing cement compound or "CEMWET" or "PIDICRETE LW" integral water proofing admixture as water proofing agent to be mixed with 50 kgs. bags shall be as recommended by the manufacture of the water proofing material, concrete work for top, bottom slab & side pardi for Overhead water tank item incl. 20 mm thk. water proofing cement plaster in C.M. 1:3 with smooth finishing & Glazes tile Dedo, vata, watering etc. Comp. to all face of tank . including locking arrangement outlet, inlet, overflow and washout outlet pipe arrangement as necessary & C.I. Cover 0.60 x 0.45 weight not less then 35 kg with locking arrangement. etc. comp as per structural drawing Including Reinforcement TMT-FE500D As per drawings and design supplied by architect and instruction given by authority and E.I.C.

Providing erecting and fixing double coated ISI water tank of required capacity each with all necessary fittings and connection etc. complete on terrace

Construction Septic tank inside dimention of 6 m in length & 3 m in width & 3 m depth including excavating any type of soil as shown and mentioned in the drawing,providing and laying 0.10 m thick plain cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone agg.) 40 mm thick IPS flooring at bottom with brick masonary 0.23 m thick walls CM 1:5 ( 1 cement : 5 coarse sand ) and intermediate partition CM 1:4 & RCC Top slabs12 cms thick in 1:2:4 (1 cement : 2 coarse sand : 4 graded stone agg) including reinforcement as per design and 15 mm thick cement plaster in CM 1:4 with floating coat of neat cement slurry inside, top and around tank below 15 cm on ground level, Also provide Two nos CI Manhole frame and cover of size 60 cm x 45 cm & 75 mm dia. PVC 6 kgf / Sq cm pressure air vent pipe in 3.00 length with cowl etc complete as per direction of Engineer in charge.

Filling in Red soil as aproved by engineer in charge For Red Soil layers in including watering, ramming and consolidating and achieving required density soil must have property of not eroding ,holds water and soft. The rate includes all labour and machinary and spreading in layers and transportation complete.

Providing & fixing of reinforcement bars ( reiforcement bars shall be paid extra under relevant item of work ) after drilling the hole of required diameter & depth ,cleanning of the same ,providing /filling the hole with Injection Mortar inserting reinforcement bar etc. complete as per Manufacturers & architects instruction.The work shall be carried out by the technical workmens/agency approved by the manufacturer and under technical supervision of Manufacturer of Injection grout including all materials,tool tackles ,labour etc.complete. (a) 8 mm. dia.bar -Holes 12mm dia Depth 150mm

Providing & fixing of reinforcement bars ( reiforcement bars shall be paid extra under relevant item of work ) after drilling the hole of required diameter & depth ,cleanning of the same ,providing /filling the hole with Injection Mortar (HY 150 or approved equivalant),inserting reinforcement bar etc. complete as per Manufacturers & architects instruction.The work shall be carried out by the technical workmens/agency approved by the manufacturer and under technical supervision of Manufacturer of Injection grout including all materials,tool tackles, labour etc.complete. (B) 10 mm. dia.bar -Holes 14mm dia Depth 100mm

Providing & fixing of reinforcement bars ( reiforcement bars shall be paid extra under relevant item of work ) after drilling the hole of required diameter & depth ,cleanning of the same ,providing /filling the hole with Injection Mortar (HY 150 or approved equivalant),inserting reinforcement bar etc. complete as per Manufacturers & architects instruction.The work shall be carried out by the technical workmens/agency approved by the manufacturer and under technical supervision of Manufacturer of Injection grout including all materials,tool tackles, labour etc.complete. (C) 12 mm. dia.bar -Holes 16mm dia Depth 120mm

Providing & fixing of reinforcement bars ( reiforcement bars shall be paid extra under relevant item of work ) after drilling the hole of required diameter & depth ,cleanning of the same ,providing /filling the hole with Injection Mortar (HY 150 or approved equivalant),inserting reinforcement bar etc. complete as per Manufacturers & architects instruction.The work shall be carried out by the technical workmens/agency approved by the manufacturer and under technical supervision of Manufacturer of Injection grout including all materials,tool tackles, labour etc.complete. (D) 16 mm. dia.bar -Holes 20mm dia Depth 160mm

Providing & fixing of reinforcement bars ( reiforcement bars shall be paid extra under relevant item of work ) after drilling the hole of required diameter & depth ,cleanning of the same ,providing /filling the hole with Injection Mortar (HY 150 or approved equivalant),inserting reinforcement bar etc. complete as per Manufacturers & architects instruction.The work shall be carried out by the technical workmens/agency approved by the manufacturer and under technical supervision of Manufacturer of Injection grout including all materials,tool tackles, labour etc.complete. (E) 20 mm. dia.bar -Holes 24mm dia Depth 200mm

Providing & fixing of reinforcement bars ( reiforcement bars shall be paid extra under relevant item of work ) after drilling the hole of required diameter & depth ,cleanning of the same ,providing /filling the hole with Injection Mortar (HY 150 or approved equivalant),inserting reinforcement bar etc. complete as per Manufacturers & architects instruction.The work shall be carried out by the technical workmens/agency approved by the manufacturer and under technical supervision of Manufacturer of Injection grout including all materials,tool tackles, labour etc.complete. (E) 25 mm. dia.bar -Holes 29mm dia Depth 250mm

Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(A) 20mm

Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(B) 25mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(C) 32mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(D) 40mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(E) 50mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure polythene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(F) 75mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(G)110 mm

Providing and fixing in position cowel went to pipes.(B) 75mm dia.

Providing and fixing in position cowel went to pipes.(C) 100mm dia

Providing and fixing water closet squatting Pan (Indian type W.C. Pan) size 580mm (Earthwork, bed concrete, foot reste and trap to be measured and paid for separately) (A) Vitreous China.(I) Long pattern = White colour

Providing and fixing wsh down water closet (European type, W.C. Pan) with integral P or S trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover to be measured and paid for separately)(A) vitreous China Pattern :(i) in white colour

Providing and fixing 100mm size P or S trap for water closet squatting pan including jointing the trap with the pan and soil pipe in cement Mortar 1:1 (1-Cement : 1-Fine sand)(A) Vitreous China.

Providing and fixing in Cement Mortar 1:3 (1-Cement : 3-coarse sand)a, pair of white vitreous China 250mm x 130mm x 30mm footrest to long pattern squatting pan water closet.

Providing and fixing 12.5 Litres low level flushing cistern with a pair, of C.I. or Mild brackets, complete with fittings such as lead valve less syphon, 15mm nom.nal size brass ball valve with polythene float, C.P brass handle unions and couplings for connections, with inlet, outlet and overflow pipes, 40mm dia. porcelain enamelled flush bend including cutting holes in walls and making good the same connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately)(A) Vitreous China (I) In white colour

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white including sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In white colour.

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white including cutting holes in walls and making good the same but excluding fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x 150mm size

Providing and fixing C.P. brass waste for washbasin or sink. (A) 32mmdia.

Providing and fixing C.P. brass waste for washbasin or sink. (B) 40mm dia.

Providing and fixing M.I. fisher union for washbasin or sink. (A) 32mm dia.

Providing and fixing M.I. fisher union for washbasin or sink. (B) 40mm dia.

Providing and fixing 100mm sand cast iron grating for gully, floor or Nahni trap.

Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.(A) 100mm dia. Each

Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size.

Providing and fixing 600mm x 120mm glass shelf with C.P. brass bracket and guard rail complete mixed to wooden plug with C.P. brass screws.

Providing and fixing toilet paper holder.(A) C.P. Brass

Providing and fixing screw down bib taps of following size.(A) Brass screw down bib tap polished bright. (i) 15mm dia.

Providing and fixing screw down bib taps of following size.(A) Brass screw down bib tap polished bright. (ii) 20mm dia.

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (i) 15mm dia.

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (ii) 20mm dia.

Providing and fixing screw down bib taps of following size.(C) Gun metal screw down bib tap. (i) 15mm dia.

Providing and fixing screw down bib taps of following size.(C) Gun metal screw down bib tap. (ii) 20mm dia.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15mm dia.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (ii) 20mm dia.

Providing and fixing brass screw down stop tap.(A) 15mm dia.

Providing and fixing brass screw down stop tap.(B) 20mm dia.

Providing and fixing brass screw down stop tap.(C) 25mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(A) 15mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(B) 20mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(C) 25mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(D) 32mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(E) 40mm dia.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(i) 20mm dia.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(ii) 25mm dia.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(iii) 32mm dia.

Providing and fixing Urinal or approved quality including conecting the Urinal with waste pipe , tap etc. complete.(A) White earthenware flat back or corner type size 430mm x 260mm x 350mm.

Providing and fixing Urinal of approved quality including connection with trap and with integral longitudinal flush pipe.(A) Squating plate pattern white earthenware 550mm x 300mm.

Providing and fixing Rubber plug for sink or wash basin.

Providing and fixing chromium plated, bottle trap with necessary couplings of approved quality for wash basin.

Providing and fixing ball cock of approved. quality as directed.(A) Copper Metal (i) 25mm dia.

Providing and fixing ball cock of approved. quality as directed.(A) Copper Metal (ii) 50mm dia.

Providing and fixing ball cock of approved. quality as directed.(B) Abonite (i) 25mm dia.

Providing and fixing ball cock of approved. quality as directed.(B) Abonite (ii) 50mm dia.

Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having weight not less than 35Kg.

Providing and fixing G.I. Rain water spout of 50mm dia. and 30cm. length.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete.[A] 15 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [B] 20 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [C] 25 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [D] 32mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [E] 40mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [F] 50mm.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the following nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of cutting and making good the walls.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 75 mm diameter with jali of the following nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of cutting and making good the walls.

Providing and laying (to level or slopes) and jointing with stiff mixture of Cement Mortar in proportion 1:1 Selt glazed stoneware pipes including testing of pipes and joints complete.(A) 100mm dia. (more than 10 ton)

Providing and laying (to level or slopes) and jointing with stiff mixture of Cement Mortar in proportion 1:1 Selt glazed stoneware pipes including testing of pipes and joints complete.(B) 150mm dia. (more than 10 ton)

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone aggregate 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(A) 100 mm dia. (112 mm Ave.bed thickness)

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone aggregate 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(B) 150mm dia. (166mm Ave. bed thickness)

Providing and laying lime concrete 1:2:4 (1-Lime putty :2-Fine samd : 4-Graded brick aggregates 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(B) 150mm dia. 450mm width (166mm Ave. bed thickness)

Extra over item 24.1 for providing salt Glazed stoneware fittings.(i) Bends of required degree (any redious) of following nominal diameters. (A) 100mm dia. (more than 10 ton)

Extra over item 24.1 for providing salt Glazed stoneware fittings.(i) Bends of required degree (any redious) of following nominal diameters.(B) 150mm dia. (upto 10 ton)

Extra over item 24.1 for providing salt Glazed stoneware fittings.(i) Bends of required degree (any redious) of following nominal diameters.(B) 150mm dia. (more than 10 ton)

Extra over item 24.1 for providing salt Glazed stoneware fittings.(ii) Taper bend of required degree of following internal diameters.(A) 100mm x 150mm (more than 10 ton)

Extra over item 24.1 for providing salt Glazed stoneware fittings.(iii) Single Junction of required angle of following internal diametrs. (A) 100mm. (more than 10 ton)

Extra over item 24.1 for providing salt Glazed stoneware fittings.(iii) Single Junction of required angle of following internal diametrs. (B) 150mm. (more than 10 ton)

Providing and laying jointing and pointing with stiff mixture of Cement Mortar 1:1 (1-Cement : 1-Fine sand) 150 mm internal diameter salt glazed stoneware half round channels. (upto 10 ton)

Providing and laying jointing and pointing with stiff mixture of Cement Mortar 1:1 (1-Cement : 1-Fine sand) 150 mm internal diameter salt glazed stoneware half round channels. (more than 10 ton)

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps. (A) 100mm x 100mm size P type. (more than 10 ton)

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps.(B) 150mm x 100mm size P or R type

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(B) 150mm (more than 10 ton)

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(C) 250mm (more than 10 ton)

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) A type depth 0.90 Metre for 150mm diameter sewer.

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (2) B type depth 1.50 Metre for 150mm diameter sewer.

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (3) C type depth 2.25 Metre for 150mm diameter sewer.

(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (4) D type depth 3.15 Metre for 150mm diameter sewer.

(I) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. or Part thereof over item No.24.27 (I) for depth from 0.9M to 1.5M.

Providing and fixing cast iron steps of size 500mm x 150mm x 22.5mm and painting with two coats of Anti-corrosive paint etc. complete.

Supplying and fixing C.I. cover 300mm x 300mm without frame for Gulley trap (Standard pattern) te weight of cover to be not less 4.53 Kg.) (more than 10 ton)

Providing and erecting at the site of work steel ventilating column of 150m internal diameter and 12.20 Metre High from G.L. to bottom of top grill including C.I. grill and base plate bolts and nuts etc. and excavation in foundation of size 120cm. x 120vcm. x 165cm. and filling the pit with first layer of cement concrete 1:3:6 mix (1-cement :3-coarse sand :6-graded stone aggregate 20mm nominal size) of 120cm. x 120cm. x 90cm. and remaining pit with B.B.C. 1:3:6 mix (1-cement :3-coarse sand:6-Brickbats 40+50mm size) and providing fillet in Cement concrete 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm. nominal size) at G.L. and 3 coats of silver paint etc. complete. (more than 10 ton)

Constructing Brick masonry road gully chamber 500mm x 450mm x 600mm including 500mm x 450mm C.I. horizontal grating wih frame complete. (more than 10 ton)

Constructing Brick masonry road gully chamber 450mm x 450mm x 775mm with vertical gating complete.

Constructing brick masonry road gully chamber 1100mm x 775mm including 500mm x 450mm (C.I. horizontal grating with frame and vertical grating complete.) (more than 10 ton)

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(i) Inside dimensions 455mmx 610mm and 450mm deep for single pipe line. (more than 10 ton)

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe line with one or two inlets. (more than 10 ton)

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(iii) Inside dimensions 600mm x mm and 450mm deep for pipe lines with three or more inlets. (more than 10 ton)

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(i) for 455mm x 610mm size.

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(ii) for 500mm x 700mm size.

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(iii) for 600mm x 850mm size.

(A) Providing sock pit of 2.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in C.M. 1:3 with finishing curing etc. complete as directed. (more than 10 ton)

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in C.M. 1:3 with finishing curing etc. complete as directed. (more than 10 ton)

RAIN WATER PERCOLATION:-Boring/drillingborewellofrequireddiaforcasing/strainerpipe,bysuitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. All types of soil 400 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer- in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer- in-charge.

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of useable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, including disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm dia

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of 200 mm dia

Providing, laying and jointing in true line and level 75 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

NSR-MR.ITEMS:-Supplying Installing and fixing wash down wall mounting EWC-P of approved shade, conforming to Pattern 2 of IS: 2556 (Part -II), with SWR Selfit Soil PVC pipe and plug bend as per specifications; glazed vitreous / Cloured European Water Closet with grouting the CI chair in side the floor/wall, rubber gaskets, connecting PVC 110mm dia soil pipe with PVC coupling, nuts, mounting cistern on WC., and solid verity heavy duty plastic seat cover as per IS-2548, of approved make; cutting and making jari work etc. complete. WALL HUNG WC WITH PP SOFT CLOSE SEAT COVER HINGES ACCESSORIES SET SIZE:365X545X360MM-CNSWHT- 961SPP , SINGLE PIECE SLIM CONCEALED CISTERN BODY WITH INSTALLATION KIT (WITHOUT FLUSH CONTROL PLATE) -JCS-WHT-2400 , JCP-CHR-2415 ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing and fixing White glazed vitreous Wash Basin Over -Counter, size 550x460 mm dia., with supporting M.S. or C.I. Brackets, 1 no, 32 mm CP Bottle trap with extension piece to wall flange with rubber adopter for waste connection and waste coupling.; with rack bolt fittings. Over Counter Type Basin , with including Jaquar - Cp-waste coupling, bottle trap CP Allied-Chrome Plate- JAQUAR-UNDER COUNTER BASIN WITH FIXING ACCESSORIES SIZE:560X430X195 MM SHAPE : OVAL -FLS-WHT-5701, PILLAR COCK AUTO CLOSING -PRS-CHR-031, ANGULAR STOP COCK WITH TRIANGULAR HANDLE AND WALL FLANGE-AQTCHR- 3057P ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing and fixing central hole basin floor mounting Pressmatic with pillar cock,flush plate etc basin wall mounted mixer with required pipes connection etc complete. PILLAR COCK AUTO CLOSING -PRS-CHR-031- ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing of Single lever Diverter for Concealed Fitting with Built in Non return Valve , for hot and cold water supply controlling with Diverter Handle with provision for both telephone shower and overhead shower complete with bath spout..SINGLE LEVER EXPOSED PARTS KIT OF HI-FLOW DIVERTER CONSISTING OF OPERATING LEVER, CARTRIDGE SLEEVE, WALL FLANGE (WITH SEALS),BUTTON ASSEMBLY SLEEVE & BUTTON (COMPATIBLE WITH ALD-079N)FLPCHR- 5079NKPM , CONCEALED BODY FOR SINGLE LEVER HIGH FLOW DIVERTER WITH BUTTON ASSEMBLY BUT WITHOUT EXPOSED PARTS ALD-CHR-079N, OVER HEAD SHOWER SINGLEFLOW 100MM DIA(ABS CP) OHS-CHR-1989 , SHOWER ARM WITH WALL FLANGE SHA-CHR-477P, BATHTUB SPOUT WITH WALL FLANGE -SPJCHR- 5429PM( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing of 3 in 1 operation Open wall Mixer with over head shower assembly , for hot and cold water supply controling with open wall mixer complete etc. Jaquar-FLR-5273UPR, Wall Mixer with Provision For Overhead Shower with 115mm Long Bend Pipe, On Upper Side, Connecting Legs & Wall Flanges etc. comp. ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing in position 15 mm C.P. brass bib cocks of best quality (as approved by the Engineer-in-Charge).FLR-5041N 2 Way Bib Cock With Wall Flange etc. comp. Jaquar-FLPCHR-5041PM ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing of Hand Shower (Health Faucet), with 8mm Dia,1Rmt Long pvc Tube and Wall Hook accessories to complete the item. Jaquar-HAND SHOWER (HEALTH FAUCET) WITH 8MM DIA 1 METER LONG FLEXIBLE TUBE AND WALL HOOK -ALD-CHR-573 ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing 15mm C.P. brass angle valve with C.P. copper connecting pipe 450 mm long and nuts, washer and brass flange complete, including cutting and making good the wall where required. Jaquar-ANGULAR STOP COCK WITH TRIANGULAR HANDLE AND WALL FLANGE AQTCHR- 3057P ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing of concealed stop cock with wall flange and complete., for the following sizes. 15mm Jaquar-CON-069FTK Exposed Part Kit of Concealed Stop Cock with Operating Lever, Collor Bush & Adjustable Wall Flange (Compatible with ALD-069FT) ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing of concealed stop cock with wall flange and complete., for the following sizes. 25mm Jaquar-CON-1081KN Flush Cock with Wall Flange 25mm with Plain Knob type ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing white vitreous china flat back urinal of size 590x375x390mm as per IS-2556 (Part-2 ) with C.I. hangers and 15mm dia. C.P. spreader,15MM cCP angular Stop Cock ,Flexible pipe Connecion, 32mm dia CP bottle trap and pipe to wall with C.P. flange complete including cutting and making good the walls and floors wherever required. Jaquar-URINAL (BACK INLET) WITH FIXING ACCESSORIES SIZE: 385X325X635 MM , AUTO CLOSING CONCEALED URINAL FLUSH VALVE WITH WALL FLANGE ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing of concealed type urinal sensor with concealed body, divertor, cock with wall flange and complete., for the following sizes. SNR-STL-51087 Sensor Concealed Type Flushing Valve for Urinal Complete Set with Installation Box with Control Cock (Battery Operated) ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing of Flush Valve Auto operation cock with wall Flange 32mm with lever knob complete in all respects including cutting and making good the walls etc. FLV-1085N Metropole Flush Valve Dual Flow 32mm Size (Concealed Body) with Exposed Shut Off Provision & Round Flange (3.0/6.0 Lts. Per Flushing) ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing of Pressmatic concealed flush Valve Auto operation cock with wall Flange 15mm with lever knob complete in all respects including cutting and making good the walls etc. for Urinal area Flsuh :- PRS-073 Auto closing Concealed Urinal Flush Valve With Wall Flange ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing of Pressmatic open type anguler cock concealed flush Valve Auto operation cock with wall Flange 15mm with lever knob complete in all respects including cutting and making good the walls etc. for Urinal area Flsuh :- PRS-077 Urinal Valve Auto Closing System with Built-in Control Cock & Wall Flange ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing of Pressmatic open type Bib Tap wall Monted type Auto operation cock with wall Flange 15mm with lever knob complete in all respects including cutting and making good the walls etc. for Press Matic Bib cock- Wall Mounted :- PRS-043 Bib Cock Auto Closing System with Built-in Control Cock With Wall Flange ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing of Pressmatic open type Bib Tap floor Monted type Auto operation cock with wall Flange 15mm with lever knob complete in all respects including cutting and making good the walls etc. for Press Matic Bib cock- floor Mounted :- PRS-031 Pillar Cock Auto Closing System ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing of manual operation type Bib Tap wall Monted type cock with wall Flange 15mm with lever knob complete in all respects including cutting and making good the walls etc. Bib cock :- CON-037KN Bib Cock Also available CON-047KN Bib Cock with Wall Flange ( Jaquar, Kohler, Cera or Eq. )

Supplying Installing & fixing stainless steel sink, R.S. or C.I. Painted brackets painted, 40mm dia. C.P. waste, C.P. brass chain and rubber plug, strainer with necessary C.P. brass unions complete including painting the fittings and cutting and making good the walls wherever required, with CP sink cock with raised "J" shaped swinging spout. NIRALI - GRACE - PLAIN - 510 X 432 MM (ONLY BOWL) SINK COCK WALL MOUNTED WITH J-SHAP SWIING OPERATION - ( Nirali-Jaquar, Kohler, Cera or Eq. )

Suppying, installing, testing and commissioing of centrifugal end suction / monoblock pumps with c.i. casing, Bronze impeller, SS Shaft and driven by 415 V AC, 3 phase, 50HZ., motor running at 2900 rpm speed and shall be supplied with all accessories viz., base plate, coupling, motor, starter panel, cabling up to panel, earthing,suction, delevery & header pipes & valves etc., complete. (Garden & irrigation water pumps : To pump UG tank to Garden Feed Water Tank)( Grundfos, ITT Lowara, or Eq.Make)Capacity : 5 mtr3/hr.2 Nos. main Pumps ( 1 Working + 1 Stand by Set)

WATER COOLER ; Supply, installation, testing & commissioning of S.S. storage type water cooler with inbuilt with on line U.V. fultration along with built all intercnnectio piping, supports and valve and other electrical requirment ,along with inbuilt storage tank with nessesarry accessories, safety valve, air valve, drain arrangement, all insturumentation, base frame, necessary electrification, etc. complete for Drinking Water supply. ( Voltas, Blu star, Power H2o Make) Capacity : 80 storage capacity. Complete as directed by site eng. incharg.

Constructing Grit/ Silt chamber in brick masonry with cement mortar 1:4, waterproof cement plastering 12mm thick for inside and outside using waterproofing compound, CC 1:4:8 bedding with 1:2 smooth finishing inside with chamfering, RCC M-20 slab in M-20 using black trap, san and cement with 150mm thick RCC slab and providing and fixing medium type FRP manhole cover and farm etc. comp.( Size 1500 x 1500 x up to 2.0mtr depth)

PUDDLE SLEEVES:-Providing & Installing of the G.I. heavy duty Puddle Sleeve in the UGT & OHT water tanks , durring the construction of the RCC tanks. The pipe and flazes nut bolt material are as per the IS recommondation must be follow. all works must properly finishing as per site eng. Incharge slab & Beams where ever req. 200 mm pipe dia x 600mm length

Providing & Installing of the G.I. heavy duty Puddle Sleeve in the UGT & OHT water tanks , durring the construction of the RCC tanks. The pipe and flazes nut bolt material are as per the IS recommondation must be follow. all works must properly finishing as per site eng. Incharge slab & Beams where ever req. ,150 mm pipe dia x 600mm length

Providing & Installing of the G.I. heavy duty Puddle Sleeve in the UGT & OHT water tanks , durring the construction of the RCC tanks. The pipe and flazes nut bolt material are as per the IS recommondation must be follow. all works must properly finishing as per site eng. Incharge slab & Beams where ever req. ,100 mm pipe dia x 600mm length

Providing & Installing of the G.I. heavy duty Puddle Sleeve in the UGT & OHT water tanks , durring the construction of the RCC tanks. The pipe and flazes nut bolt material are as per the IS recommondation must be follow. all works must properly finishing as per site eng. Incharge slab & Beams where ever req. ,80 mm pipe dia x 600mm length

Providing & Installing of the G.I. heavy duty Puddle Sleeve in the UGT & OHT water tanks , durring the construction of the RCC tanks. The pipe and flazes nut bolt material are as per the IS recommondation must be follow. all works must properly finishing as per site eng. Incharge slab & Beams where ever req. ,50 mm pipe dia x 450mm length

BORE WELL:-Supply installation, testing, commissioning of Bore well submersible pump to be installed in the tube well of required indicated capacity and head as per relevant IS for Bore water lifting with suitable submersible vet type, water cooled, squirrel case motor conforming to IS 9283, working of 3-phase, 50Hz +/- 3% 415 VAT +/- 10%, AC supply 2900 RPM synchronous speed with 10mtr. copper conductor flat cable from pump to starter panel with cables and termination ( all supports clamps pipe fittings mechanical seal, bearing, bush, strainer, etc. comp., Casing C.I., S.S. CF8M impeller, bronze casing, wearing and bearing bush, TC mechanical seal, S.S. bearing, S.S. shaft with sleeve, S.S. strainer, and M.S. morter along with water guard, single phase preventor with all cables of appropriate size control and instrumentations, switches, testing, and installation along with testing. The scope shall also include delivery isolation valve & NRV with PVC piping (400 dia Drill well @200mm dia MS. heavy class pipe : BORE WELL) Assume 75 TO 100mtr depth) ( 10 TO 15 MTR CU. PER HR. OUT PUT FLOW RATE with potable water quality ) (8 TO 10HP PUMP.)

Point Wiring Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. with medium class Rigid PVC pipe and accessories

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling, complete with earth continuity and necessary connection with primary light with accessories erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed. with medium class 25 MM DIA Rigid PVC pipe and accessories

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling complete with 6A Modular type switch and hum free EME four or more step type electronic fan regulator with separately mounted and accessories with earth continuity of following type erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.

Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type accessories

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [I] For 6A Plug with 2-1.5 sq.mm Cu. Wire

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [II] For 16A Plug with 2-2.5 sq.mm Cu. Wire

Wiring for the 250 volts single phase and neutral 16 amps switched socket outlet with 4.0 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make with concealed or surface mounted 25 mm dia medium gauge PVC Conduit including providing and fixing of 16 amps 5 pin switch socket outlet of approved quality color make & design in 2 mm thick GI box and earthing of fixtures and the outlet box with 2.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire.

Providing & erecting Switch board for Computer or electric apparatus consisting of following items in single board erected on PVC / Metal board with 3 mm thick PC (Polycarbonate) / Acrylic sheet erected as directed 1 no. 6A/16A universal plug-switch combined. 4 nos. 6A Switch 4 nos. 6A 5 pin Plug For Modular Type Accessories

Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or Open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm thickness

Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 32 mm rigid PVC pipe of 1.6-1.8 mm thickness

Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 40 mm rigid PVC pipe of 1.6-1.8 mm thickness

MAINS : ( not for Point wiring ) Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size Supplying and Laying of 4 nos. of 6 sq mm Cu. FRLS flexible wires with 2 nos 2.5 sqmm Cu. FRLS flexible wires

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size Supplying and Laying of 2 nos. of 6 sq mm Cu. FRLS flexible wires with 1 nos 2.5 sqmm Cu. FRLS flexible wires

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size Supplying and Laying of 2 nos. of 4 sq mm Cu. FRLS flexible wires with 1 nos 2.5 sqmm Cu. FRLS flexible wires

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size Supplying and Laying of 2 nos. of 2.5 sq mm Cu. FRLS flexible wires with 1 nos 1.5 sqmm Cu. FRLS flexible wires

Distribution Board Distribution Board-VTPN Providing and erecting Sheet Steel powder coated Vertical MCB distribution board (VTPN) - flush / surface mounted double door (IP54) fitted with copper insulated busbar, isolated neutral bar, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3, suitable for 63/100 AMP TPN MCCB + RCCB as incomer and three phase outgoing as per following .(The DBs should be used of same company of MCB to be used) (A)4 way outgoing

Distribution Board-TPN Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for (B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b) sheet steel double door (iv)12 way

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for (B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b) sheet steel double door (iii)8 way

Distribution Board-SPN Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for (A) single phase incoming and horizontal single phase outgoing (b) sheet steel double door (IP-43) (iv)12 way

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for (A) single phase incoming and horizontal single phase outgoing (b) sheet steel double door (IP-43) (iv)8 way

MCB providing and erecting Miniature circuit breaker single pole 0.5A to 2A system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark

Miniature circuit breaker single pole suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark 6 to 25 A SP MCB

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 6 to 32 A DP MCB

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 40 A DP MCB

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 25 to 32A / 30mA/100 mA DP ELMCB

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 40 A / 100 mA DP ELMCB

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (a) 6 to 32 Amp. Cat.III

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (b) 40 Amp. Cat.III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 6 to 32A FP MCB

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 40 A FP MCB

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 63 A FP MCB

Approved make four pole moulded case circuit breaker having breaking Capacity ICU of 35KA. At 415 V, having normal current rating up to 125A. With fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all iternal connections & complete erected in existing 16 G.M.S. housing. ICS= 100% of ICU only.

Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display. Also comprised permanent ON/OFF switching. Programming switches & housed in fire proof thermoplastic enclosure & transparent cover erected as required with necessary connection erected as directed.

Supplying & erecting power contactor ,AC3 duty for time switch complete erected as per direction Cat III (B) 2 pole 250V 32 Amp.

Supplying & erecting power contactor ,AC3 duty for time switch complete erected as per direction Cat III (D) 4 pole 440V 40 Amp.

Plastic enclosure fitted with DIN rail suitable for incorporating Three /Four nos. MCB

Sheets steel powder coated enclosure suitable for incorporating One/Two nos. MCB.

SITC of IP65 Polycarbonate enclosure for FP MCCB

Cable Trench Making trench in soft soil of suitable width of 90 cms deep for laying cable or locating the fault all over the run and backfilling the same and making the surface proper. Providing and erecting iron clad cable route marker duly marked with ELE.CABLE of size 23 cms.X 12 cms. Flushed with ground in cement foundation as directed by Engineer in charge. The width shall be as per requirement

Covering of cable with second class bricks laid cover the cable crosswise & also on both sides with covering of 7. 5 Cms. layer of sand above & below cable (cable shall be laid in 0.9mtr.deep & 0.4 Mtr.wide trench). Where there are more than one cable in the trench on either side of the cable, 5 Cms. over lapping of bricks shall be provided.

Providing cement concrete.for foundation or for concrete filling in 1:2:4 ratio with 20 to 25 mm stone metal duly plastered with necessary curing for pole muffing or any other purpose.

Providing burnt brick masonry with 1:6 cement concrete duly plastered including watering, stacking joint on exposed faces, rocking at joints on exposed faces and watering complete

Construction of brick masonry pulling chamber 450 mm x 450 mm inside clear size and depth up to 0.6 meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum 200 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame and 450 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer In charge complete in all respect.

Construction of brick masonry pulling chamber 600 mm x 600 mm inside clear size and depth up to 0.60 meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum 200 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame and 600 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer In charge complete in all respect.

Construction of brick masonry pulling chamber 750 mm x 750 mm inside clear size and depth up to 0.75 meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum 200 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame and 750 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer In charge complete in all respect.

Construction of brick masonry pulling chamber 1000 mm x 1000 mm inside clear size and depth up to 1.0 meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum 200 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame and 900 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer In charge complete in all respect.

Cable Tray Providing and fixing approved make Ladder type cable tray. Made from M.S sheet. The cable tray should be bended as per IS 2062/1079 shall be fabricated of double bended channel section longitudinal members with single bended Channel section. Rungs of members welded to the base of tha longitudinal members at 250 mm c/c spacing . as per IS and shall be coated with hot dip galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge.. 400 X 100 X 2 mm Thick

Providing and fixing approved make Perforated C type cable tray. Made from CR sheet steel. The cable tray should be single or double bended as per required and as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge.. (2) 100 X 50 X 1.6 mm Thick

Providing and fixing approved make Perforated C type cable tray. Made from CR sheet steel. The cable tray should be single or double bended as per required and as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge.. (5) 300 X 50 X 2 mm Thick

Fabrication Supplying , fabricating and installation of various sizes MS race way / junction boxes/clamps/hangers for Cable Tray, Light Fixture made out of specified size sheet/Angle/Flat/rod/ channel etc as per design with all necessary accessories like bend, junction boxes, coupler, Anchor fastener, Bolt Nuts, etc.. & work from MS structure for other work with anchor fastener of Hilti make and necessary hardware with necessary welding has to be done to complete the job from ISA / ISMC / PLATE. The job also includes to paint the structure with two coats of red oxide and two coats color of enamel paint as approved and recommended by consultant. Complete in all respect to be installed at any height with all necessary arrangements. Contractor has to complete the work up to satisfaction of Consultant

Cables Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 35 sq.mm x 3.5c Al. XLPE Arm. Cable

Cables Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 25 sq.mm x 4 c Al. XLPE Arm. Cable

Cables Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 16 sq.mm x 4 c Al. XLPE Arm. Cable

Cables Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 10 sq.mm x 4 c Al. XLPE Arm. Cable

Providing & erecting XLPE(IS:7098) (I)-88 ISI armoured cable multistrand copper conductor for 1.1 KV. To be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size cable. 6 sq.mm x 4 c cu. XLPE Arm. Cable

Providing & erecting XLPE(IS:7098) (I)-88 ISI armoured cable multistrand copper conductor for 1.1 KV. To be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size cable. 4 sq.mm x 4 c cu. XLPE Arm. Cable

Providing & erecting XLPE(IS:7098) (I)-88 ISI armoured cable multistrand copper conductor for 1.1 KV. To be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size cable. 6 sq.mm x 3 c cu. XLPE Arm. Cable

Providing & erecting XLPE(IS:7098) (I)-88 ISI armoured cable multistrand copper conductor for 1.1 KV. To be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size cable. 4 sq.mm x 3 c cu. XLPE Arm. Cable

Supplying & erecting XLPE (IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be erected as directed of following size 3 core 2.5 Sq.mm.

Cable Termination SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 35 sq.mm x 3.5c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 25 sq.mm x 4 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 16 sq.mm x 4 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 10 sq.mm x 4 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 6 sq.mm x 4 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 4 sq.mm x 4 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 6 sq.mm x 3 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 4 sq.mm x 3 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. 3 core 2.5 Sq.mm. MV Switchgear & Power Panels Supply, Unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning main L.T. panel board, fabricated from M.S. sheet & folded channel totally enclosed cubical type compartmentalized. Scope Covers Unloading at Site, Store in Weather Proof Condition, Shift to the Location Basement / GF / FF, Grouting, Installation, Testing & Commissioning complete in all respect & As per the instruction of Architect / Consultant / Engineer Incharge. Scope also covers Co ordination with Panel Manufacturer. Design, fabrication, assembling, supply, installation , testing of Panels for 415 V, 3 phase, 50 Hz, 4 wire power supply system. Panels shall be fabricated out of 2 mm thick CRCA sheet steel in cubical formation, compartmentalized in Form 4b Construction, floor mounted, free standing and shall be dust and vermin proof. 3 mm thick cable gland plate, shall be provided both at the top and the bottom of the panel. All large panels shall be provided with lifting hooks. Distribution panels shall be fabricated in accordance with the specifications. Note : Panel vendor has to provide Surge Protection at every stage of the Distribution. 1) Supporting rigid steel framework. 2) Cubicle type, 14 gauge CRCA sheet steel enclosed. 3) Complete with interconnections and distribution bus bars. 4) Proper bonding to earth. 5) Painting/lettering on Breakers and distribution boards, the location they serve, providing on each panel its circuit diagram. 6) Providing cable clamps / supports within distribution boards cable alley. 7) TPN ACB’s / MCCB’s shall mean 3 pole ACB’s / MCCB’s with adequate size of neutral link. 8) All MCB’s shall be of minimum 10 KA breaking capacity. 9) The breaking capacity of MCCB’s are mentioned panel wise. 10) All motor feeders MCCBs shall be of motor duty. 11) Distribution panels shall be Powder Coated with Siemens gray paint shade no. RAL-7032 of IS-5. 12) Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-1993. a) IP 52 for indoor panels. b) IP 54 for Service area panels. c) IP 65 for outdoor panels. 13) All MCCB’s shall be provided with operating mechanism for door interlock & with the roraty handle. 14) Current density of aluminium shall be 1 sq mm for 0.8 amps for rated current of bus bars and current density of copper shall be 1 sq.mm for 1 amps for rated current of bus bars. 15) Tinned copper earth bus as specified in the BOQ / SLD shall be provided through out the length of each board. 16) All measuring instruments (Meters) shall be of digital electronic with LED of approved make and compatible with BAS. 17) All hinged door shall be earthed through 2.5 sq mm tinned braided copper wire. 18) All panels shall have provision of the following: a) IP 55 for outdoor panels. b) Pad locking of MCCB’s handles in “OFF” Position. 19) Additional set of C.T.s, potential free contacts, connectors, contactors with wiring etc are to be provided for BAS including space required for various transducers in Main Switch Board sections. Only transducers shall be supplied by BAS contractor. 20) All the C.T.s should be auto short link type. 21) All the MCCB's should be with rotary handle. 22) All MCB’s used for protection of resistive and lightly inductive load shall be type “B” characteristic and inductive (motor) load shall be of type “C” characteristic and discharge lamps and UPS etc. shall be of type D characteristic. 23) All incoming and outgoing air circuit breakers shall be placed on middle portion of the vertical in single tier formation. 24) All PTs / control transformer shall be provided with centre tap earth secondary. 25) If Any descripancy found in SLD & BOQ, it should be brought in the notice of the Client / Consultant, Client / Consultant's decision will be final in case of any descripancy. 26) All outdoor panles should be provided with minimum 600mm height fabrication stand with all side 2mm thick M.S. powder coated sheet. 26) G.A. Drawing should be checked & Finalised by consultant before fabrication.

Supplying and erecting led lamps with following wattage capacity of 220 to 240 voltage, minimum 15000 burning hours life, 500 V in built-surge protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp holders, pf >= 0.5 (A) LED Lamps integral type, with PC diffuser suitable LAMP holder (ii) 5 to 8 watts, Cat-III

SITC of Any kind of Light Fixture with Basic Rate of Rs. 5000

SITC of Any kind of Light Fixture with Basic Rate of Rs. 10000

Exhaust Fans : Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 RPM with square frame ABS body with inbuilt lowers & square frame.

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM [A] 305 mm dia 900 RPM

Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete having 3blades with aluminium blades with , canopy & 30 cms. down rod erected with 24/ 0.2, 3 core flexible wire with earthing.(fan colour shoud be Gray)

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete with necessary 24/ O.20, 3 core flexible wire with earthing.

Street Light Pole Supplying and erecting approved make Octagonal pole made from HR sheet steel. The pole should be made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/2633/4759, suitable suspend local wind speed with integral Junction box consist of terminal plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and arrangement for cable termination to be erected With Suitable foundation (Included) as per details given by manufacturer considering site requirement. (D) 6 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm thickness with 200mmX200mmX12mm base plate, 4-M20 Bolts and 600mm long with necessary G.I. J Bolts .Approx Pole weight 59 kg

Supplying and erecting approved make Octagonal pole made from HR sheet steel. The pole should be made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/2633/4759, suitable suspend local wind speed with integral Junction box consist of terminal plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and arrangement for cable termination to be erected With Suitable foundation (Included) as per details given by manufacturer considering site requirement. (G) 8 Mtr. Long 70 mm Top X 155 mm bottom dia, 3 mm thickness with 260mmX260mmX16mm base plate, 4-M20 Bolts and 600mm long with necessary G.I. J Bolts Approx Pole weight 84 kg

UPS Supplying and erecting approved make online Un-interruptible Power Supply system comprising flat cum-boost charger with IGBT base rectifier & Inverter & sealed maintenance free SMF batteries. The charger having operating capacity for input 160-270V AC & inverter having output 230V,50 Hz Ac with 0.8 load power factor with battery, over/under voltage output with over load & short circuit protection equipment. The system housed in CRC sheet duly powder coated paint with following power backup.with MS painted batteries stand, 10% Overload capacity for momentary load. (D) 5 KVA with 1Hr Backup

Earthing Supplying & erecting funnel type earthing having earth plate of following size burred in specifically prepared earth pit 3 mtr. below ground with 40 kg. charcoal and salt with alternate layers of charcoal & salt, 20mm.dia. G.I. pipe with Funnel with a wire mesh for watering & bricks masonry block, C.I. Cover complete as per para 7.3 of IS 3043 with necessary length of double Galvanised Iron / copper earth wire No 6 SWG bolted with lug to the plate and covered in 12 mm dia. G.I. pipe 2.5 mtr long complete connected to the nearest switch gear with end socket as per direction & duly tested by earth tester confirming to IS (As per drawing) with following specification with 60 x 60x 0.315 cms. Copper earth Plate

Supplying & erecting in earthpit of minimum bore dia. 225mm size ASH or approved make Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising, connection terminal dia of 14 mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications. For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA)i.e. independent Earthing located in other than normal soil i.e. Soft Rock, Marshy Soil etc.. -Length of Pipe : 3 Mtrs. -Back filling Compound :2 nos Bags of 25 Kg.

Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe with necessary coupling buch buried in specially prepared earth pit & G.I. earth wire of 8 SWG erected & connected as directed (For pole)

Earth wire/strips : Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG.

Providing and erecting Annealed bare Copper wire 8 to 16 SWG.

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for control panel, relays, power switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. Supplying and Laying mains with 1 no. of 6 sq mm Cu. PVC insulated FRLS flexible wire ( Green Color Only )

Providing & erecting approved make street light / wall mounting junction box compression moulded from SMC (thermoset plastic) vertical sliding cover having locking with square head stud loop in / loop out in built terminal suitable for four core cable, waterproof of I.P. 54 protected with clamp or bolt nut & earth bolt of following size. (C) 327mm x 254mm x 120 mm

Telephone Distribution Providing and installing of all conduiting and structured cabling for telephone system including providing and fixing of the following: 1) All necessary specials and fittings 2) Approved cover plates for inspection, junction and outlet boxes. 3) 2 mm thick outlet boxes (MDF) and junction boxes. 4) All fixing accessories such as clips, nails, screws etc. 5) Providing and fixing approved saddles, hooks and grouting the same as required, in the case of all exposed conduit work. 6) Embedding conduits and accessories in wall, floors etc. during construction and / or cutting chases and making good as necessary in the case of all concealed conduit work. Supply and installation, testing and commissioning following size telephone tag block in lockable 16 gauge sheet steel enclosure complete as required. 10 pair Krone type tag block

PVC & HDPE Conduits Supply & laying of 25 mm dia. rigid PVC conduit of 2.0-2.2 mm thick heavy gauge with all accessories.

Supply & laying of 40 mm dia. rigid PVC conduit of 2.1 -2.3 mm thick medium gauge with all accessories.

EPABX SITC of Digital / PCM / TDM EPABX System having SMT design, system with flexible universal slots. Inbuilt Auto attendant facility, Minimum 15 Nos. conference, Analog extension line, Calling GSM, E&M line, PRI / EI & VOIP program me through Analog telephone digital key from Ethernet, public address cord, shall have unrestricted simultaneous dialing facility, QSIG protocol on PRI, 95 / STD / ISD / Local-Locking, Class of Service, Quick Dial-Single Digit dialing of any two external number, Once only ring device, Chairman / Secretary - Do not disturb Facility, Power Down Mode, Hot Line, Hot Outward Dialing, Day Night Mode, Auto Call Back, Barge-in, Call Pick Up & Call Transfer, Call transfer while Ringing with Voice Guide System, (DISA), Caller ID (CLI), CLI Base ECF, CLI Base routing Internet Ready Port, External Music Port, Call Budgeting, Call Most Calculation (ASMDR), DID Direct Inverse Dialing, External Music Input, Fax Homing, Global Directory Printing with following capacities [[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] [A] No of Extension 16, No of Junctions 6, 8 Port IP Resource in-built, 4 Port Web base Video Conferencing, No of expandable ports : 48, Operators Console - 01 Compatible : ISDN

Supplying & erecting push button type telephone instrument having speaker phone Caller ID & hands free dialing system & 30 memories with display system Single line [[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

Providing and erecting IP Phone with display with all IP system supported [[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

Telephone Point Wiring Supply and laying of specified make 0.51 mm dia Tinned copper telephone wire of specified make to be done in prelaid PVC pipe of 25 mm dia/raceway of specified make, but without the cost of pipe or raceway. (the wire is to be drawn from Krone connector of respective area to outlet point ) 5 pair telephone wire

Telephone Point Wiring Supply and laying of specified make 0.51 mm dia Tinned copper telephone wire of specified make to be done in prelaid PVC pipe of 25 mm dia/raceway of specified make, but without the cost of pipe or raceway. (the wire is to be drawn from Krone connector of respective area to outlet point ) 10 Pair Telephone Wire

Supply, Installation, Testing And Commissioning of Solid Cable Cat 6, 4 pair, UTP.

Telephone Outlet Point SITC OF PowerCat 6 DataGate Jack, 568A/B - Yellow with Dust Cover / Blank/ One Telephone Point to be done with Cat -6 Information outlet Socket, Back Box, Face Plate for all telephone point. Average Length to be considered as 50 Meter. Cable Laying, Labling, Ferrule, Testing, Certification to be included in cost. 20 Years of Certification is required. Test reports of Level-4 Scanners only.

SITC OF DG+ Jack (Diecast)Cat6A 568A/B, Shtd- Black (Information Outlet for Data) with Faceplate, back box CAT-6A standards. Cable Laying, Labling, Ferrule, Testing, Certification to be included in cost. 20 Years of Certification is required. Test Reports of Level-4 Fluke Scanners Only.

SITC OF 24 Port Layer 2 Fully Managed Network Switch with 24 10/100/1000Base T Ports and 4 GE SFP Ports. Include Limited Lifetime Warranty.

Supply, installation, testing and commissioning of 24 Port loaded Patch Panel

SITC of CAT6 UTP 24AWG PATCH CORD:1M,Plug 30U' Snag less

Supply, Installation, Testing and Commissioning of Equipment rack / Console as per requirement

CCTV Supply, Installation, Testing & Commissioning of Network TDN IR Mini Dome Camera, 1/2.9" CMOS, 5 MP @ 25fps, Triple stream, Min. Illumination required 0.25 lux @ color, WDR 120dB, Min. Pixels 2560 x 1920, Shutter Speed 1/30000 - 1/5; Adavance Video Compression technology such as H.265 / H.264 / MJPEG, 3mm~8mm, MFZ lens, HLC, 3DNR, Minimum Edge Intelligence Video Analytics: Motion Detection, Camera Tampering, Intrusion/Object enter area; 4 nos Privacy Mask, Smart IR with upto 30m IR distance, AES-128/256, PCI Data Security Standard compliance, 128GB SD card support, DC12V, PoE (IEEE 802.3af) (Class 2), IP 66, IK10, Having Operating temp range : –10°C to 50° C. Certifications: ONVIF Profile S, G compliant, UL, CE/EN, FCC Part 15 & RoHS compliant along with mounting brackets suitable for Cieling / Wall mounting & required accesories as per site requirement.

Supply, Installation, Testing & Commissioning of 5MP IP Network TDN IR Bullet Camera, 1/2.8" CMOS, 5 MP @ 25fps, Triple stream, Min. Illumination required 0.05 lux @ F1.4 (color), WDR>120dB, Min. Pixels 2560 x 1920, Shutter Speed 1/30000 - 1/30; Adavance Video Compression technology such as H.265 HEVC / H.264 / MJPEG, Smart Codec, 2.7-13.5 mm 5X motorized focus & zoom lens, P-IRIS, HLC, 3DNR, Minimum Edge Intelligence Video Analytics: Motion Detection, Video Tampering, Intrusion, Loiter, Line crossing, Unattended object, Missing object, Face detection; 5 nos Privacy Mask, 4 IR LEDs Smart IR with upto 60m IR distance, Stream encryption, AES-128/256, PCI Data Security Standard compliance, FIPS Chipset Built-In, 256GB SD card support with SD card encryption, Dual channel Audio G.711a / G.711 Mu / G.726, Alarm: 2 In/ 1out, In-built Heater; PoE+ (802.3 at) and 12V DC/24V AV; IP 66 / IP 67 / NEMA 4X, IK10, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S, G compliant, UL, CE (EN 50130-4 & EN 55032) , FCC Part 15 & RoHS compliant along with mounting Brackets suitable for Pole / Wall mounting & required accesories.

Supply, Installation, Testing and Commissioning of Number Plate Recognition Camera with Ultra-low illumination technology, 1/1.8" Progressive Scan CMOS, 0.004 lux color @ F1.53, 0 lux B/W with IR LEDs on @ F1.53, Slow shutter, 6 MP 25/30fps, 4.1 to 16.4 mm/F1.4 Motorized VF lens with Smart Focus, H.265 and H.264/MPEG4, Triple-Stream, Support SD/SDXC Card up to 128GB, IP67, IK10, DC12V/PoE, up to 50m IR range, Bracket & junction box included, Smart Feature-setAudio/Alarm IO UL, CE, FCC & RoHS compliant and Cyber Security Complient.

Supply Installation Testing & Commissioning of Network Storage Manager(NSM) supporting ONVIF Profile S & G, PSIA, real time streaming protocol (RTSP) standards, emerging technologies in the industry, like 4K resolution, H.265 video compression codec. System proposed shall have scalability of 4 to 120 cameras per NSM with sufficient licenses to record all the cameras in this requirement. NSM shall support simultaneous recording, live monitoring, playback/search of recorded video for up to 4K resolution on all cameras, taking snapshots and viewing presets for PTZ cameras and system management. NSM shall have integrated Dashboard to easily monitor the health and recording status, Flexible retention time / archive time for cameras, Smart Motion detection, Role-based operator privileges supporting Windows and local users, Video Archiving, Multi-stream support, Advanced security features with encryption support for communication between desktop client to NSM and secure https login for Web Client and Mobile apps, Event history and operator log reporting with export to PDF, Crystal Reports, MS Excel/MS Word. NSM Shall support scheduled backfilling of the recordings from the edge storage/SD card of cameras to the NSM using ONVIF Profile G for robust recording against temporary network failure, N+1/N+M recorder failover and failback automatically or manually to have maximum system uptime and recording continuity.

Supply, Installation, Testing & Commissioning of Network Video Management & Monitoring Software (NVMMS) system with distributed architecture to collect, manage and present video from all the cameras and supports emerging technologies in the industry, like 4K resolution, H.265 video compression codec. The NVMMS shall have option to support database redundancy and 1+1 and N+M NSM failover features for unforeseen/maintenance scenarios for increased system reliability. NVMMS shall support NSM's licenses upto 100 cameras & 3 user clients without any additional version upgrade. The NVMMS should support network joystick controller, GPU rendering support for H.264 and H.265 decoding , video on demand, Adaptive video throttling, rule engine, operatore role management, server based Video Motion Detection (VMD), edge storage backfill support, bookmark with manual comment, bookmark based search, timeline search, Preview search, synchronous playback from all NSMs, monitor wall support, surrounding camera mode, Cybersecured with features such as Digital Signing, compliance, HTTPS & SSL base, smart web client, secured firewall configuration, password expiry, non-recoverable password; support ANDROID & iOS phones, seamless integration with intgegrated security platform which provides HSDK&API for further integration with 3rd party systems. NVMMS shall support iLIDS certified Analytics like Licence plate recognition and intrusion/LoiteTrace.

Intel® Core™ i7-12th generation, 4.0 GHz or better, Xeon 11th Generation 4.4 GHz or higher, Minimum 32GB RAM, Minimum 512 GB separate SSD hard drive for OS, DVD-R/W, 6 GB/s SAS/SATA RAID Card, RAID 1, 5, 10. 2 NIC cards supporting network throughput of 256 Mbps/425 Mbps for Incoming/outgoing, Graphics Adapter - Intel®IRIS XE Graphics or equivalent for local client GPU rendering support, Windows Server 2019 (64-bit OS versions recommended), Microsoft SQL Express 2012. Video rated or Enterprise drive, 7200 RPM SATA/SAS recommended, Video Monitor Resolution- 1280x1024 pixels, 32 bit with keyboard and mouse. The NSM shall be complete system for satisfactory surveillance operations with all necessary softwares, licenses, required PC Hardware, Storage, accessories etc., civil, electrical works & peripheral items, as required.

Supply, Installation & Commissioning of NVMS workstation/PC with minimum Intel Core i7-12th Generation, 3.4GHz, 8GB RAM, Windows 10 Professional (64 Bit) OS, DVD R/W, Integrated Intel HD graphics 530 and NVIDIA Quadro NVS 315 1 GB PCIE x 16 LP supporting 4 Monitors. The NVMMS shall be complete system for satisfactory surveillance operations with all necessary softwares, licenses, required PC Hardware, storage, accessories etc., civil, electrical works & peripheral items, as required as per specification in Annexure A at site of work inline with the Engineer in Charge instructions..

Supply, Installation, Testing And Commissioning of 55" 4k UHD resolution Monitor - 120 HZ for viewing the cameras

Supply, Installation, Testing and Commissioning of Equipment rack / Console as per requirement

SITC of 48 x 10/100/1000BASE-T ports 4 x Gigabit GbE/SFP combo ports Advanced L2 switching and security features L2+ Static Routing Optional “standard mode” or “surveillance mode” management user interface

SITC of 24 x 10/100/1000BASE-T PoE ports 4 x Gigabit RJ45/SFP Combo ports Advanced L2 switching and security features L2+ Static Routing Optional “standard mode” or “surveillance mode” management user interface 193 W PoE budget

SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-Fully Loaded

SITC of CAT6 UTP 24AWG PATCH CORD:1M,Plug 30U' Snag less

Supply and laying of PowerCat 6A U/FTP CM 4 Pair Cable, LSZH Sheath - Violet of specified make to be done in prelaid PVC pipe of 25 mm dia / raceway of specified make, but without the cost of raceway or pipe ( the wire is to be drawn from HUB \ Switch of respective area to outlet point ) with the cost of the crimping with material.

Supply and laying of Cat-6 STP LSZH UV outdoor cable in PVC conduit with termination as per TIA

Supply installation testing and commissioning of power amplifier 480 W power amplifier in a 3U high 19” housing, 70 V / 100 V and 8 Ohm outputs, 100 V input for slave operation on 100 V speaker line. Bosch LBD1938/00

Supply installation testing and commissioning of Voice Alarm Controller Built-in message manager and 240 W amplifier, Six‑zone outputs, 6 emergency and 6 business triggers, internal 16 MB flash ROM, Two BGM inputs,Two RC station connectors. Bosch LBB 1990

Supply installation testing and commissioning of Wall mount volume controller . Bosch LM1V36P

Supply installation testing and commissioning of High- End Low Noise Copper Speaker Cable 1.5 Sqm. PVC jacket Krystal

Supply installation and commissioning of Equipment Rack – 28U Designed As Per Site Requirement Elixer

Fire Detection System Supply, Installation, Testing And Commissioning of UL864, 10th Edition Microprocessor based 4 loop, True Peer-to-Peer Networkable Addressable Fire Alarm Control Panel with minimum 600 characters LCD display, 4000 event plus 1000 alarm log history events, QWERTY keypad for programming. The panel should be equipped with sufficient numbers of loops considering 20% spare capacity in each loop. Each loop shall have a capacity of minimum 250 analog addressable devices. The panel shall work in degrade mode in case of CPU failure, Products not having this feature may offer Redundant CPU. Four access levels, flash EPROM, 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working and 30 mins in alarm condition. The panel shall be compatible with Integrated 8 channel Digital Voice Evacuation System Controller capable of broadcasting Evacuation Messages on same peer-to-peer Network and 2 ways Communication Fire Fighters System capable of supervising all the speaker circuits with adequate zone control and accessories. Failure of Fire Panel CPU shall not result in failure of DVC operation. The Fire Fighters Telephone System shall be capable of having minimum 30 Telephones in conference in multiple FFT Risers.

Supplying, Installation, Testing and Commissioning of Network Repeater Panel with minimum 10" Color Touch Screen display with QWERTY Keypad, mapping minimum 2,00,000 points on network. The NRP shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of NRP operation.

Supply, Installation, Testing And Commissioning of UL Listed Graphics User Interface for Monitoring & Control of complete Fire, Voice Evacuation & Telephone Talkback System. The GUI based main network software shall network with other panels on True Peer-to-Peer network. It shall be capable of graphically representing each facility being monitored with floor plans and icons depicting the actual locations of the various systems, and / or sensors’ locations. It shall have the facility to change the sensitivity of any detector. The software shall be capable of monitoring 200 Nodes with 100 Mbps Transmission rate on Fibre Optics Network and 12 Mbps Transmission on cable and 2,50,000 network points. The software shall be capable to Monitor & Control all the Digital Voice Evactuation as well as 2 way communication from main control room using voice signals over Fire Network along with the Fire detection signal. The Graphic workstation shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of GUI.

Supply, Installation, Testing And Commissioning of Automatic printer capable for interface with NCS and provided with RS 232/RS 485 protocol port. It shall be standard cartage with 80 characters per line as per all requirements of technical specifications & contracts works.

Supply, Installation, Testing And Commissioning of UL268, 7th Edition Addressable Multi-criteria Photo-Thermal Detector with sensitivity range of 0.5 to 4.0% obs/ft.The intelligent multi criteria detection device shall include the ability to combine the signal of the thermal sensor with the signal of the photoelectric signal in an effort to react hastily in the event of a fire situation. It shall also include the inherent ability to distinguish between a fire condition and a false alarm condition by examining the characteristics of the thermal and smoke sensing chambers and comparing them to a database of actual fire and deceptive phenomena. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches.

Supply, Installation, Testing And Commissioning of UL Listed Addressable Rate of Rise Heat Detector rated at 8.3 deg C/min. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches.

Supply, Installation, Testing And Commissioning of UL listed Addressable Manual Call Point (Pull down / Break Glass Type). The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device.

Supply, Installation, Testing And Commissioning of UL Listed Sounder cum Strobe rated at 80 dBA @ 3m for Audible annunciation and 115cd flashintg at 1 Hz for visual indication. UL Listed

Supply, Installation, Testing And Commissioning of Addressable Control Module for Sounders / Strobes / Sounder cum Strobes. The control module shall provide supervised NAC output rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supply, Installation, Testing And Commissioning of UL Listed Isolator Module for Isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supply, installation, testing & Commissioning of Battery pack suitable for back up of 4 hours with charger in case of Alarm condition.

Supply, installation, testing & Commissioning of response indicator

Supply, installation, testing & Commissioning Fire Exit Signage boards with 3hrs battery backup

Supply & laying of 2 Core X 1.5 sq.mm. FRLS Armoured PVC Insulated copper cable

Supply & laying of 4 Core X 1.5 sq.mm. FRLS Armoured PVC Insulated copper cable

Miscellaneous Supplying & erecting carbon dioxide (CO2) fire extinguisher user of following capacity with necessary clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in wall complete. For 4.5 Kg Capacity, including maintaining/ renewal validity of all Co2 fire extinguisers up to the completion of O&M period

Supplying rubber matting of following thickness as per IS : 15652/IEC61111 4mm

Providing and erecting metallic vitrified danger notice board for MEDIUM VOLTAGE installation to be erected as per IS.

Providing printed instruction chart both in English and Gujarati and duly framed with front glasses, for treatment of person suffering from Electric shock

Providing the A0 Color size print of the Final Plan / SLD duly framed out on Glass for Electrical room & BMS Room

Providing the A1 Color size print of the Final Plan / SLD duly framed out on Glass for Electrical room & BMS Room

Providing the A2 Color size print of the Final Plan / SLD duly framed out on Glass for Electrical room & BMS Room

Providing the A3 Color size print of the Final Plan / SLD duly framed out on Glass for Electrical room & BMS Room

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth for laying of cable. below ground / road surface for enclosing cable and back filling the same to make ground as per original. (A)50 mm dia

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth for laying of cable. below ground / road surface for enclosing cable and back filling the same to make ground as per original. (B)90 mm dia

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth for laying of cable. below ground / road surface for enclosing cable and back filling the same to make ground as per original. (B)120 mm dia

Liason / Follow UP with Supply Co. Filling the necessary application to supply co. following up and getting the supply filling the necessary test report to the supply co. inclusive. All official fees including security deposits will be paid by the client and out of pocket expenses shall be of contractor. 1. To get temporary power supply 2. To get the H.T. Connection 3. To get all approval from CEIG and supply company 4. To get Lift approval

FIRE FIGHTING PUMPS:- Supply, installation, testing & commissioning of electric driven Hydrant & Sprinkler Pump suitable for automatic operation consisting of the following:Horizontal end suction centrifugal pump complete with mechanical seal and including necessary arrangement for testing of pump Squirrel cage induction motor suitable for 415 V, 50 Hz, AC supply of suitable rating for the above pump with synchronous speed of 2900 RPM T.E.F.C. type and conforming to IP:55 and flexible coupling and coupling guard with the pump. Common bed plate of fabricated mild steel channel or cast iron type. Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required. Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required. The pump shall be of the following specifications:Discharge-1620 lpm,Head - 56 mtr No. of stage preferred - Single / Double Speed RPM - 2900 Material of construction a) Impeller - Bronze b) Casing - C.I. c) Shaft & Shaft Sleeve - SS-410 d) Bearing - Grease Lubicated e) Seal & Make - Mechanical Type of pump - End suction HP :- 45HP ( 35 KW.)

Supply, installation, testing & commissioning of electric driven Jockey Pump suitable for automatic operation consisting of the following: Horizontally mounted centrifugal end suction pump complete with mechanical seal and including necessary arrangement for testing of pump.Squirrel cage induction motor suitable for 4440 V, 50 Hz, AC supply of suitable rating for the above pump with synchronous speed of 2900 RPM T.E.F.C. type and conforming to IP:55 and flexible coupling and coupling guard with the pump.Common bed plate of fabricated mild steel channel or cast iron type.Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required.The pump shall be of the following specifications:Discharge - 180 lpm Head - 56 m No. of stage preferred - Multistage Speed RPM - 2900 Mover - Electric Motor Driven Material of construction a) Impeller - Bronze b) Casing - C.I. c) Shaft & Shaft Sleeve - SS-410 d) Bearing - Grease Lubicated e) Seal & Make - Mechanical Type of pump - End suction HP:- 4.0 HP ( 3 KW.)

Supply, installation, testing & commissioning of diesel engine Hydrant Pump suitable for automatic operation consisting of the following: Horizontal split casing centrifugal pump complete with mechanical seal and including necessary arrangement for testing of pump Water cooled Diesel Engine developing suitable BHP at 1500 RPM for the Pump, common bed plate for mounting of engine and pump, RCC foundation and vibration damping arrangement by Cushy Foot and engine panel provided by engine manufacturer, connection to Engine Starting Panel as per item (4), sealed maintenance free batteries of 24 V, 88 AH. Rate shall include Exhaust pipe of required length with asbestos lagging, muffler, day oil tank of 400 lts with first charge and manual oil pump set.Flexible coupling and coupling guard with the Pump,Common bed plate of fabricated mild steel channel or cast iron type.Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required. Engine panel Sealed maintenance free batteries of 24 V, 88 AH --2 Nos. (1 working + 1 standby)Exhaust pipe of required length with asbestos lagging, muffler Day oil tank M.S. pipe Metal) of 400 lts with first charge and manual oil pump set and necessary piping and structural work to place tank at upper level from pump in pump room,Discharge -1620 lpm, Head - 56 m No. of stage preferred - Single / Double Speed RPM - 1450 Mover - Diesel engine driven Material of construction a) Impeller - Bronze b) Casing - C.I. c) Shaft & Shaft Sleeve - SS-410 d) Bearing - Grease Lubicated e) Seal & Make - Mechanical Type of pump - END SUCTION

Supply, installation, testing & commissioning of electric driven automatic fire booster Pump suitable for automatic operation consisting of the following: Horizontal end suction centrifugal pump complete with mechanical seal and including necessary arrangement for testing of pump. Squirrel cage induction motor suitable for 415 V, 50 Hz, AC supply of suitable rating for the above pump with synchronous speed of 2900 RPM T.E.F.C. type and conforming to IP:55 and flexible coupling and coupling guard with the pump. Common bed plate of fabricated mild steel channel or cast iron type. Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required. The pump shall be of the following specifications: Discharge-900 lpm, Head - 35 m No. of stage preferred - Single / Double Speed RPM - 2900 Material of construction a) Impeller - Bronze b) Casing- C.I. c) Shaft & Shaft Sleeve - SS-410 d) Bearing - Grease Lubicated e) Seal & Make - Mechanical ,Type of pump - End suction f) H.P.- 13.41 HP ( 10 KW.)

Providing and fixing air vessel for fire pumps as per following specifications: Diameter - 450mm, Shell thickness - 8mm, Dish ends - 10mm, Height - 1500mm Finishing - Two coats of Red enamel paint of first grade over one coat of primer externally & two coats of epoxy coating inside Material of Construction - M.S. Test Pressure - 15 Kg./sq.cm.

Providing and laying the PVC insulated & sheathed FRLS Armoured cables of 1.1 K.V. Aluminium Conductor 3 core x 95 sq.mm

Providing and laying the PVC insulated & sheathed FRLS Armoured cables of 1.1 K.V. Aluminium Conductor 3 core x 10 sq.mm (cable from pump room to terrace for booster pump)

Providing and laying the PVC insulated & sheathed FRLS Armoured cables of 1.1 K.V. Aluminium Conductor 3 core x 16 sq.mm (cable for jockey pump)

Providing and fixing in position cable end termination glands for above mentioned cables 3 core x 95 sq.mm

Providing and fixing in position cable end termination glands for above mentioned cables 3 core x 10 sq.mm (cable from Booster Pump to terrace Remort Panel )

Providing and fixing in position cable end termination glands for above mentioned cables 3 core x 16 sq.mm (cable for jockey pump)

Providing, installation, testing, & commissioning of Remote Panel for fire fighting terrace pump with push buttons for manual operation (the remote panel shall be located at ground level) all complete.

Supplying, laying and connecting of following size 1.1 kV grade copper conductor armoured control cable on wall or on existing cable tray with clamping, dressing or drawn in existing ducts all as required (For remote panel for fire fighting terrace pump). 3 core x 6 sq.mm

Providing, installation, testing, & commissioning of pressure switches for Hydrant, Sprinkler, Standby and Jockey pump including necessary wiring upto control panel & other materials.

Providing and fixing fire retardent / extinguishing electrical insulated synthetic mat of 5mm thick ±10% conforming to latest BIS doc no.-ET-02(5440) meeting requirements of IS 3043 / IS 5216 (Part I, II & III), IS 8437 & IEC 479 suitable for all voltages not exceeding 3.3 KV AC supply and having minimum width of 1000mm ± 20mm and including supply of required quantity of adhsive / compound and fixing the same at site as per site requirement.

Fabricating and installing following size of perforated M.S. pipe cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders including painting, etc., as required. 150mm width x 50mm depth x 1.6 mm thickness.

Providing & fixing 25 mm x 5 mm M.S. pipe Strip in on surface or in recess for connections etc as required.

Providing & fixing 25 mm x 5 mm M.S. pipe Strip in 40 mm dia GI pipe from earth electrode as required.

SUCTION AND DELIVERY PIPES AND VALVES FOR FIRE FIGHTING PUMPS:- Providing and fixing M.S. pipe _ Claa-C heavy Duty suction & delivery headers / pipes for fire fighting pumps (IS. 1239 heavy duty) including all fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete alongwith painting M.S. pipe pipe with coat of Red Oxide primer and two or more coats of synthetic enamel paint of approved colour and quality to give an even shade including surface preparation. 15 mm nominal bore

Providing and fixing G.I.-pipe -Class- B Medium Duty suction & delivery headers / pipes for fire fighting pumps (IS. 1239 heavy duty) including all fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete alongwith painting G.I.-pipe pipe with coat of Red Oxide primer and two or more coats of synthetic enamel paint of approved colour and quality to give an even shade including surface preparation. 25 mm nominal bore

Providing and fixing G.I.-pipe -Class- B Medium Duty suction & delivery headers / pipes for fire fighting pumps (IS. 1239 heavy duty) including all fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete alongwith painting G.I.-pipe pipe with coat of Red Oxide primer and two or more coats of synthetic enamel paint of approved colour and quality to give an even shade including surface preparation. 80 mm nominal bore

Providing and fixing G.I.-pipe -Class- B Medium Duty suction & delivery headers / pipes for fire fighting pumps (IS. 1239 heavy duty) including all fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete alongwith painting G.I.-pipe pipe with coat of Red Oxide primer and two or more coats of synthetic enamel paint of approved colour and quality to give an even shade including surface preparation. 100 mm nominal bore

Providing and fixing G.I.-pipe -Class- B Medium Duty suction & delivery headers / pipes for fire fighting pumps (IS. 1239 heavy duty) including all fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete alongwith painting G.I.-pipe pipe with coat of Red Oxide primer and two or more coats of synthetic enamel paint of approved colour and quality to give an even shade including surface preparation. 150 mm nominal bore

Providing and fixing M.S.-pipe -Class- C Medium Duty suction & delivery headers / pipes for fire fighting pumps (IS. 1239 heavy duty) including all fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete alongwith painting G.I.-pipe pipe with coat of Red Oxide primer and two or more coats of synthetic enamel paint of approved colour and quality to give an even shade including surface preparation. 200 mm nominal bore (6.0 thick min.)

Providing and fixing cast iron wafer type Butterfly valve of the following size complete with bolts, nuts, washers and neoprene gaskets as per specifications. 80 mm nominal bore

Providing and fixing cast iron wafer type Butterfly valve of the following size complete with bolts, nuts, washers and neoprene gaskets as per specifications. 100 mm nominal bore

Providing and fixing cast iron wafer type Butterfly valve of the following size complete with bolts, nuts, washers and neoprene gaskets as per specifications. 150 mm nominal bore

Providing and fixing cast iron wafer type Butterfly valve of the following size complete with bolts, nuts, washers and neoprene gaskets as per specifications. 200 mm nominal bore

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : 100 mm nominal bore

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : 80 mm nominal bore

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : 150 mm nominal bore

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : 200 mm nominal bore

Providing and fixing reinforced Neoprene flexible pipe connectors with all accessories on all pumps delivery.Suitable for 20 Kg/cm2 80mm

Providing and fixing reinforced Neoprene flexible pipe connectors with all accessories on all pumps delivery.Suitable for 20 Kg/cm2 150mm

Providing and fixing of nickel plated brass / nonferrous alloy fullyway ball valve (minimum working pressure of 20 bar ) with operating handle of approved make. 25 mm nominal bore

Providing and fixing of nickel plated brass / nonferrous alloy fullyway ball valve (minimum working pressure of 20 bar ) with operating handle of approved make.15 mm nominal bore

FIRE HYDRANT SYSTEM(External & Internal) (All Fire Fighting Hardware Should be ISI Mark) :-Providing, fixing, jointing and testing heavy quality 'B' class Medium duty G.I. Pipe conforming to IS 3589/IS 1239 for pipes upto 150 mm dia. including forged threaded/socked(weldable) i.e. tees, bends, elbows, unions, reducers, draining arrangement, flange joints, rubber insertion, nuts & bolts etc. as required including fixing of pipework on walls, slabs etc. with M. S. supports (duly painted), adjustible hangers. Note: Joints for pipes and fitttings upto 50 mm diameter shall be threaded joints using Teflon Tape or equivalent bonding tape on the threads. Joints for pipe and fittings above 50 mm diameter shall be welded joints.Above ground pipe-with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. :- 25 mm dia

Providing, fixing, jointing and testing heavy quality 'B' class Medium duty G.I. Pipe conforming to IS 3589/IS 1239 for pipes upto 150 mm dia. including forged threaded/socked(weldable) i.e. tees, bends, elbows, unions, reducers, draining arrangement, flange joints, rubber insertion, nuts & bolts etc. as required including fixing of pipework on walls, slabs etc. with M. S. supports (duly painted), adjustible hangers. Note: Joints for pipes and fitttings upto 50 mm diameter shall be threaded joints using Teflon Tape or equivalent bonding tape on the threads. Joints for pipe and fittings above 50 mm diameter shall be welded joints.Above ground pipe -with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation.:- 80 mm dia

Providing, fixing, jointing and testing heavy quality 'B' class Medium duty G.I. Pipe conforming to IS 3589/IS 1239 for pipes upto 150 mm dia. including forged threaded/socked(weldable) i.e. tees, bends, elbows, unions, reducers, draining arrangement, flange joints, rubber insertion, nuts & bolts etc. as required including fixing of pipework on walls, slabs etc. with M. S. supports (duly painted), adjustible hangers. Note: Joints for pipes and fitttings upto 50 mm diameter shall be threaded joints using Teflon Tape or equivalent bonding tape on the threads. Joints for pipe and fittings above 50 mm diameter shall be welded joints.Above ground pipe -with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation.:- 100 mm dia

Providing, fixing, jointing and testing heavy quality 'B' class Medium duty G.I. Pipe conforming to IS 3589/IS 1239 for pipes upto 150 mm dia. including forged threaded/socked(weldable) i.e. tees, bends, elbows, unions, reducers, draining arrangement, flange joints, rubber insertion, nuts & bolts etc. as required including fixing of pipework on walls, slabs etc. with M. S. supports (duly painted), adjustible hangers. Note: Joints for pipes and fitttings upto 50 mm diameter shall be threaded joints using Teflon Tape or equivalent bonding tape on the threads. Joints for pipe and fittings above 50 mm diameter shall be welded joints.Above ground pipe-with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. :- 150 mm dia

Providing and laying of 'B' class Medium duty G.I. Pipe conforming to IS 3589/IS 1239 including all GI/MS fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type ) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete with one coat of 4 mm thick 'PYPKOTE' or COATEK anti rust pipe protection including approved primer & surface preparation of pipes as per manufacturers specifications and lap of 25 mm to make an impermeable layer on G.I. Pipes in trenches or underground pipes below soil all complete.Under ground pipe-with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 80 mm dia

Providing and laying of 'B' class Medium duty G.I. Pipe conforming to IS 3589/IS 1239 including all GI/MS fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type ) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete with one coat of 4 mm thick 'PYPKOTE' or COATEK anti rust pipe protection including approved primer & surface preparation of pipes as per manufacturers specifications and lap of 25 mm to make an impermeable layer on G.I. Pipes in trenches or underground pipes below soil all complete.Under ground pipe-with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 100 mm dia

Providing and laying of 'B' class Medium duty G.I. Pipe conforming to IS 3589/IS 1239 including all GI/MS fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type ) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete with one coat of 4 mm thick 'PYPKOTE' or COATEK anti rust pipe protection including approved primer & surface preparation of pipes as per manufacturers specifications and lap of 25 mm to make an impermeable layer on G.I. Pipes in trenches or underground pipes below soil all complete.Under ground pipe :- 150 mm dia(UNDERGROUND)with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation.

Painting for M.S. /G.I, pipe . pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 25 mm dia

Painting for M.S. pipe . pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 80 mm dia

Painting for M.S. /G.I, pipe . pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 100 mm dia

Painting for M.S. /G.I, . pipe . pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 150 mm dia

Providing and fixing S.S landing valve conforming to IS -5290 with 63 mm dia instantaneous female coupling on the outlet with S.S. orifice flange 6 mm thick as required to maintain 3.5 Kg/sq.cm., blank cap and chain, necessary companion flanges ( as per table "E") nuts, bolts, washer and gasket complete as per specification. (ISI marked) Single outlet

Providing and fixing first aid fire hose reel drum wall mounting, swinging type fitted with 20 mm dia 30.0 m long high pressure hose to I.S. 5132 with 25 mm outlet gunmetal nozzle with shut off valve (I.S. 884-1969). Name of Manufacturer should be embossed on the drum.

Providing and fixing 63 mm dia 15m long EPDM lined fabric lined hose including SS male and female instantaneous type coupling approved by fire authority, machine wound with copper wire complete in all respects.Hose shall conform to IS 636 TypeII and coupling to IS 903 -1975 (ISI marked)

Providing and fixing standard short size SS branch pipe with gunmetal nozzle 20 mm dia outlet with standard instantaneoustype 63 mm dia coupling. (conform to IS-903).

Providing and fixing standard fireman's axe ( tested for 20000 Volts) with heavy insulated rubber handle.( ISI marked)

Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia.

Providing and fixing brass ball valve (full bore type) with plastic coated lever and screwed female ends tested to 20 Kg/ cm2 of approved quality as specified.20mm

Providing and fixing brass ball valve (full bore type) with plastic coated lever and screwed female ends tested to 20 Kg/ cm2 of approved quality as specified. 25 mm dia

Providing and fixing door with frame for all internal fire hydrants fabricated from 16 SWG Alumunim of size 750 x 1200 x2100 mm double door including 2 nos allen key lock for locking along with padlock arrangement & fully glazed with 4 mm thick float glass approved by local Fire Authority, stove enameled fire red finish with " fire hose' written on front suitable to house 15 mm long four length of canvas hose with couplings,one no of branch pipe, one fire mans axe and two numbers of portable extinguishers, first aid fire hose and supports for hoses, branch pipes, Axe and hose reel. as per approved design including necessary fixing arrangement for hoses & axe and branch pipe.) FOR INTERNAL.

Providing and fixing dial type pressure gauge with isolation cock and chrome coated copper pipe at hydrant station. Dial diameter 100 mm calebration 0-15 kg/ sq.cm.

Providing and fixing cast iron wafer type Butterfly valve -PN-1.6-of the following size complete with bolts, nuts, washers and neoprene gaskets as per specifications. 80 mm dia

Providing and fixing cast iron wafer type Butterfly valve-pn-1.6- of the following size complete with bolts, nuts, washers and neoprene gaskets as per specifications. 150 mm dia

Providing and fixing cast iron dual plate wafer type non return valves. 150 mm dia

Providing and fixing gunmetal fire brigade inlet head as per IS:904 Specification tested for 20 Kg/cm2 with 63 mm dia instantaneous type inlet and 150mm dia. flanged outlet with built-in check valve for fire brigade connection to under ground tanks and fire risers including campanion flanges as pertable " E" including nuts, bolts & washers etc. Four way

Providing and fixing gunmetal fire brigade inlet head as per IS:904 Specification tested for 20 Kg/cm2 with 63 mm dia instantaneous type inlet and 150mm dia. flanged outlet with built-in check valve for fire brigade connection to under ground tanks and fire risers including campanion flanges as pertable " E" including nuts, bolts & washers etc. Two way

Providing and fixing suction coupling for fire brigade drawl of water from tank with 150 mm dia GI (Medium) pipe and foot valve .

Providing, fixing ,testing and commissioning external (yard) hydrant "STAND-POST" type conforming to IS:908-1975 and comprising of stand post for single outlet of hot diped class ' C' G.I.-pipe Pipe of 100 mm dia at the with instantaneous spring lock type Stainless steel female coupling of 63 mm dia for connecting to hose pipe, single headed SS valves conforming to type A of IS: 5290-1977, GI tee tapping from underground mains, flange riser and any other accessories etc. as per specification complete as required.

Providing and fixing fire hose cabinet fabricated from 16 gauge M.S.sheet with locking arrangement and hanging arrangement for accessories painted "Fire Red" with Stove enameled paint "Fire Hose" written on front including suitable supports to place 900 mm above ground level properly anchored, approximately size 800 X 600 X 250 mm deep (to house two lengths of canvas hose with couplings, branch pipe with nozzle for external hydrants) FOR EXTERNAL.

SPRINKLER SYSTEM :- Providing and fixing 'B' class Medium duty G.I. Pipe conforming to IS 3589/IS 1239 complete with GI / MS fittings like couplings, bends, elbows, tees, offsets,reducers, flanges as per table 'E' etc. including cutting and making good the walls complete.Pipes upto 50 mm dia threaded joint with holdtite, 65 mm dia and above should be welded joint (all type).with one coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour to give an even shade including surface preparations. :- 25 mm dia

Providing and fixing 'B' class Medium duty G.I. Pipe conforming to IS 3589/IS 1239 complete with GI / MS fittings like couplings, bends, elbows, tees, offsets,reducers, flanges as per table 'E' etc. including cutting and making good the walls complete.Pipes upto 50 mm dia threaded joint with holdtite, 65 mm dia and above should be welded joint (all type).with one coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour to give an even shade including surface preparations. :-32 mm dia

Providing and fixing 'B' class Medium duty G.I. Pipe conforming to IS 3589/IS 1239 complete with GI / MS fittings like couplings, bends, elbows, tees, offsets,reducers, flanges as per table 'E' etc. including cutting and making good the walls complete.Pipes upto 50 mm dia threaded joint with holdtite, 65 mm dia and above should be welded joint (all type).with one coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour to give an even shade including surface preparations. :-40 mm dia

Providing and fixing 'B' class Medium duty G.I. Pipe conforming to IS 3589/IS 1239 complete with GI / MS fittings like couplings, bends, elbows, tees, offsets,reducers, flanges as per table 'E' etc. including cutting and making good the walls complete.Pipes upto 50 mm dia threaded joint with holdtite, 65 mm dia and above should be welded joint (all type).with one coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour to give an even shade including surface preparations. :-50 mm dia

Providing and fixing 'B' class Medium duty G.I. Pipe conforming to IS 3589/IS 1239 complete with GI / MS fittings like couplings, bends, elbows, tees, offsets,reducers, flanges as per table 'E' etc. including cutting and making good the walls complete.Pipes upto 50 mm dia threaded joint with holdtite, 65 mm dia and above should be welded joint (all type).with one coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour to give an even shade including surface preparations. :-65 mm dia

Painting of M.S. pipe with one coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour to give an even shade including surface preparations. 25 mm dia

Painting of M.S. pipe with one coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour to give an even shade including surface preparations. 32 mm dia

Painting of M.S. pipe with one coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour to give an even shade including surface preparations. 40 mm dia

Painting of M.S. pipe with one coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour to give an even shade including surface preparations. 50 mm dia

Painting of M.S. pipe with one coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour to give an even shade including surface preparations. 65 mm dia

Painting of M.S. pipe with one coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour to give an even shade including surface preparations. 80 mm dia

Painting of M.S. pipe with one coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour to give an even shade including surface preparations. 100 mm dia

Painting of M.S. pipe with one coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour to give an even shade including surface preparations. 150 mm dia

Providing and fixing 15 mm gunmetal sprinkler head with quartz bulb and set to operate at specified temperature pendent/ upright/ side wall as per instruction and fixing with loctite. Pendent Type 68 C

Providing and fixing 15 mm gunmetal sprinkler head with quartz bulb and set to operate at specified temperature pendent/ upright/ side wall as per instruction and fixing with loctite. Side Wall Type 68 C

Providing and fixing 15 mm gunmetal sprinkler head with quartz bulb and set to operate at specified temperature pendent/ upright/ side wall as per instruction and fixing with loctite. Upright Type 68 C

Rossete Plate:-Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.1200mm

Providing & fixing 25mm dia gunmetal inspecting & testing assembly with ball valve(3 nos.), gunmetal sight glass, by pass valve & connected to drain line.

Providing and fixing brass ball valve full bore type with plastic coated lever approved quality, tested to 20 Kg.cm.sq. 40 mm dia

Providing and fixing brass ball valve full bore type with plastic coated lever approved quality, tested to 20 Kg.cm.sq. 50 mm dia

Providing and fixing cast iron wafer type Butterfly valve-PN-1.6- of the following size complete with bolts, nuts, washers and neoprene gaskets as per specifications. :- 100 mm nominal bore

Providing and fixing cast iron wafer type Butterfly valve -PN-1.6-of the following size complete with bolts, nuts, washers and neoprene gaskets as per specifications. :- 65 mm nominal bore

Providing and fixing electricaly operated flow indicating switches model System Sensor in sprinkler branch line on each floor with necessary junction box installed in accessible place (Wiring from switches to panel and stair case pressurisation not included) :- 100 mm dia

Providing and fixing dial type pressure gauge with isolation cock and copper pipe on main header Dial diameter 100 mm celebration 0-15 / sq. cm.

Providing and fixing 25 mm dia single acting air release valve with screwed inlet.

Providing and fixing cast iron dual plate wafer type non return valves. :- 150 mm dia .

Providing and fixing cast iron dual plate wafer type non return valves.:- 100 mm dia .

Providing, Installation, testing and commissioning of Control Valve inclusive of: - 150 mm dia butterfly Valve,Alarm Valve with Water Motor Gong, Pressure gauge and other miscellaneous Valves and fittings as required.

Providing and laying 2 x 2.5 sq mm copper conductor PVC sheathed armoured cable for connecting fire alarm Panel to flow switch.

Supplying, Installation, Testing and commissioning of Annunciator panel for flow control switch, providing Audio/Visual indicating of actuation of automatic sprinkler system for each zone complete as per specifications with provision for 3 zones (2 working and 1 spare for future). 'Indication of zone fire, 'Indication of zone fault, 'Fire/Fault hooter, 'Alarm cancel for fire/fault, 'Battery for emergency

Manual Fire Alram System. Providing, fixing, testing and commissioning of Manual Call Point.

Providing, fixing, testing and commissioning of Hooter

Providing, fixing, testing and commissioning of Conventional Fire Alarm Panel 12 Zone

Providing, fixing, testing and commissioning of 2 Core X 1.5 Sqmm Flexible copper Cable with PVC Conduit.

Providing, fixing, testing and commissioning of 3 Core X 1.5 Sqmm flexible copper Cable with PVC Condiut.

On - Off Pump Trigger System. :- Providing, fixing, testing and commissioning of On -Off Switch.

Fire Resistant Door Double Leaf Hinge Type (2 Hour Fire Rated) 1.00 mm thick GI Sheet cladded 40mm thick shutter complete with GI frame (Single Ribet – Frame Profile 100 x 57mm) made from 1.20mm thick GI Sheet & Fixing arrangements AS PER BS 476 PART- 20 & 22 & IS: 3614 Part - II for Integrity, Stability.Door Size: 2000mm (W) x 2100mm (H) Including below Accessories S.S. Ball Bearing Hinges- 6 Nos Vision Panel with Fire Glass of Size: 200 x 300mm - 2 Nos Heavy Duty Door Closer - 2 Nos Heavy Duty Door Closer - 2 Nos Panic Exit Device for Double Leaf Door - 1 No. External Trim Bar (Panic Latch) - 1 No.

HAND APPLIANCES :- Providing and fixing ABC type fire extinguishers consisting of welded MS cylindrical body, squeeze lever discharge valve fitted with pressure indicating gauge internal discharge tube, 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket, conforming to ISI finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. Capacity 6.0 kg. I.S.I. Marked.

Providing and fixing Trolley type foam fire extinguishers cap. 50 liters. 50 litres capacity

Providing and fixing in position Co2 gas type fire extinguishers of 4.5 kg. capacity each.

Providing and fixing Trolley type Co2 gas fire extinguishers cap. 9 liters will be provided for transformer area.

Providing and keeping in position standard sand buckets filled with clean sand and painted red from outside at various places.

Providian’s Escape Sigane:- Photoluminescent rigid plastic, 2mm thickness, printed on high quality glass paint with UV resistance, 5 year warranty, material used-non radioactive, non-phophorous, non toxic and lead free. Available in different types & sizes, time after removing the light source (in minutes):- 60 minutes, luminescent intensity(milicandelas*per square meter-mcd/sqm):30 mcd/sqm. Luminescent intensity greater than 0.32 mcd/sqm, period of light decay* (in minutes) :3100 (1) “Fire Exits” ( Size 365 x 119 x 84 mm or nearest )

(2)Fire exit signs of standard size ( Size 450 x 200 x 84 mm or nearest ) (photoluminous type.(glowing in dark type)Providing and fixing portable fire extinguishers of approved make ISI marked of following Capacity at the places shown on Drawing & mentioned in CFO letter

Providing, fixing, testing and commissioning of below Auto Glow Signages. In Case of Fire do not use Lift ,Use Staircase 8"x 8"

ADDITIONAL WORK:- Core Cutting in RCC wall, beam, columns and roof as required locations of required size & depth and repairing , making it goods complete . Size 40mm to 80mm dia ( avarge depth 200)

Core Cutting in RCC wall, beam, columns and roof as required locations of required size & depth and repairing , making it goods complete :- Size 100mm to 200mm dia ( avarge depth 200)

Providing and fixing cast iron following size complete with bolts, nuts, washers and neoprene gaskets as per specifications. 200mm dia y strainer in main suction header

Supply & fixing of air cushion tank at the top most point of wet risers, comprising of : 200mm dia 1.2 mtr. high 6mm thick tank,1 no. 80mm dia flanges inlet 1 no. 25mm dia drain points 1 no. pressure gauge with stop valve

P/ F PCC foundation for fire pumps as requiredfor Electric driven fire pump

P/ F PCC foundation For diesel driven fire pump

P/ F PCC foundation For jockey pump

Earthing with M.S. pipe earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with M.S. pipe earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Costing for Liasion work with authority and obtaining NOC and all relevant applicable approvals including required drawing work.

M D AND SONS (BID ID -20681)

Ekta Construction (BID ID -20683)