Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹20.0 LAccepted-AOC | L1 | Accepted-AOC BEING LOWEST BIDDER | |
| 2 | L2₹22.1 L+₹1.8 L (8.78%)Rejected-Finance | L2 | Rejected-Finance OTHER THAN LOWEST |
Tender Value
₹22.4 L
EMD Value
₹44,700
Closing Date
30 Nov 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE 865 EWS
GE 865 EWS, PIN-913 865 C/o 56 APO
PROVN OF 01 X TOILET BLOCK NEAR OFFICE COMPLEX OF 360 COMPANY ARMY SERVICE CORPS SUPPLY TYPE G AND SR TO BLDG NO T 403 P 25 UNDER AGE BR I OF GE 865 EWS AT LEH
2022_MES_559954_1
865/EWS(NIT-86)/2022-23
Open Tender
Civil Works
Item Rate
270 days
GE 865 EWS
As per tender documents and as per policy in vogue
9 documents required · 9 mandatory
₹500
GE 865 EWS
₹44,700
Yes
23 Dec 2022
27 Oct 2022
9 Dec 2022
27 Oct 2022
30 Nov 2022
15 Nov 2022
Amount
Demolition of un reinforced cement concret as in ground floor of any description and in any position not other wise specifically provided for and Removing demolished material to a distance and depositing out site of MoD land Where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed by Engineer-in-Charge.
Demolition of un reinforced cement concret in position of any description and in any position not other wise specifically provided for and Removing demolished material to a distance and depositing out site of MoD land Where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed by Engineer-in-Charge.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tile to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.
Dismantling wall/floor and ceiling boards (fiber, pulp, inlsulation, blankets) any thickness including covered fillets and supporting members complete all as specified and as directed
Dismantling timber scantling in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section as in framed work complete all as specified and directed.
Demolition of precast concrete block/Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.
Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegitation upto and including roots complete all as specified and directed by Engineer-in-Charge.
Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt), complete all as specified and directed by Engineer-in-Charge.
Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt), complete all as specified and directed by Engineer-in-Charge.
Taking down shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each of complete all as specified directed by Engr-in-charge.
Taking down shutters of any description area not exceeding 1 Sqm each of complete all as specified directed by Engr-in-charge.
Hacking out old broken glass (any thick ness, size, quality or description) from wooden panes or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and as directed by Engr-in-Charge.
Dismantling plain or corrugated steel /fibre sheeting any guage thickness including nanital or similar pattern complete all as specified and as directed by Engr-in-Charge.
Dismantling wrought iron or mild steel work of any description complete all as specified and directed by Engr-in-Charge.
M&L for 9mm thick prelaminated particle board, medium interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed to walls of any description or timper scantling with screws to timber frame work, complete all as specified and as directed by Engr-in-Charge. MAKE: NOVA PAN/GREEN PLY BHUTAN BOARD/MYSORE WOOD BOARD/CENTURY PLYWOOD
M&L for 9mm thick prelaminated particle board, medium interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed to ceilings of any description or timper scantling with screws to timber frame work, complete all as specified and as directed by Engr-in-Charge. MAKE: NOVA PAN/GREEN PLY BHUTAN BOARD/MYSORE WOOD BOARD/CENTURY PLYWOOD
M&L for second class soft wood clean swan as in battens for grids of ceiling and lining, plain fillets exc 13 sqcm and n.exc 25 sqcm, square/ rectangular in section, secured with nails or brads to timber frame work as in fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling complete all as directed by Engr-in-Charge.
M&L for 2nd class soft wood clean sawn as in beeding for edges of Ceiling ,lining ,or wooden flooring work fixed with nails exc 6 sqcm and n exc 13 sqcm in section.complete all as specified and as directed.
M&L for 75mm thick PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection and finished concrete surface even and smooth without using extra cement including making proper joints as per specification at an interval of 3m and change of direction complete all as specified and as directed by Engr-in-Charge.
M&L forming contraction (Dummy) joints 50 mm deep x 10mm wide for plinth protection & similar work , filled with sealing compound Grade 'A' in plinth protection complete all as specified and directed by Engr-in-Charge.
M&L for Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base, foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-Charge.
M&L pre-cast cement concrete(20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block masonery exc 10cm in width with solid block masonery with solid blocks, and setting in cement mortar 1:6 all as Specified by Engr-in-Charge.
M&L for rendering 10 mm thick rendering in cement mortar 1:6 on fair faces of brick walls or on concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.
M&L for rendering 15 mm thick rendering in cement mortar 1:6 with using water proofing compound @ 3% of cement content on on other than fair faces of brick walls or on concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.
M&L for rendering 10 mm thick rendering in cement mortar 1:4 on fair faces of brick walls or on concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.
Supply only integarl waterproofing compound complete all as specified and directed by Engr-in-Charge.
S&F 2nd class soft wood plain, solid, straight chowkets and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as directed by Engr-in-Charge.
S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165 complete.all as specified and as directed by Engr-in-Chage
Material & labour PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) as in hold fast , bed block and like complete all as specified and as directed by the Engr-in-Charge.
S&F for 35mm thick 2nd class hard wood plain framed factory made paneled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, Supply and fixed to chowkatscomplete all as directed by Engr-in-charge.Make as per PS.
S&F for 35mm thick 2nd class hard wood plain framed factory made glazed and skeletion shutter shutters , open rebated and prepared to receive glass , gauze etc (without sash bars) edges of framing plain , chamfered or rounded fitted with cut and mitred beds for securing glass etc size of members of shutters as specified in SSR part I, Section 8 , clause 8.24(a) supplied and fitted to chowkats , complete all as specified and directed by Engr-in-charge.Make as per PS.
S&F for 30mm thick 2nd class hard wood plain framed factory made glazed and skeletion window shutters , open rebated and prepared to receive glass , gauze etc (without sash bars) edges of framing plain , chamfered or rounded fitted with cut and mitred beds for securing glass etc size of members of shutters as specified in SSR part I, Section 8 , clause 8.24(a) supplied and fitted to chowkats , complete all as directed by Engr-in-charge.
M&L for framed work such as grills, greatings etc with end of bars shouldered and or riveted or forged into spikes, framed guard bars, barred iron doors ladders framed balusters , walkways, railings, framed work of water tanks and similar work confirming to Fe 290 Gde E-165 complete all as specified and directed by Engr-in-Charge.
M&L for plain sheet glass 4mm thick ordinalry quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed by Engr-in-Charge.
S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples, fixed in repairs complete all as specified and as directed by Engr-in-Charge.
S&F in repair Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples, fixed in repairs complete all as specified and as directed by Engr-in-Charge.
S&F for Aluminum, anodized, barrel tower bolts, ISI Marked, of extruded section 150 mm long, complete all as specified and directed by Engr-in-Charge.
S&F for Aluminum, anodized, barrel tower bolts, ISI Marked, of extruded section 100 mm long, complete all as specified and directed by Engr-in-Charge.
S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed by Engr-in-Charge.
S&F 100mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed by Engr-in-Charge.
S&F in repair double action floor spring hydraulically regulated made up of minium 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed by Engr-in-Charge.
S&F floor door stopper (Length of cover plate ) 150mm long aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and as directed.
S&F 75mm long aluminium anodized, butt hinges of extruded section complete all as specified and as directed.
S&F 100mm long aluminium anodized, butt hinges of extruded section complete all as specified and as directed.
S&F for 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed by Engr-in-Charge.
M&L for 25mm thick PCC 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in sub base/ levelling course for laying of screed bed complete all as specified by Engr-in-Charge.
M&L Glazed ceramic coloured tiles in vertical surfaces (350 X 250X7mm ) / (450x350x7mm) thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over rendering 10mm thick in CM (1:4) , for dado/skirting tiles.complete all as specified and as directed by the Engr-in-charge.
M & L for joint free Non-Skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer in Cement Mortar 1:4 for laying floor finishes complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY
M & L for joint free Non-Skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer in Cement Mortar 1:4 for laying floor finishes complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY
M&L for 20 mm thick granite stone (any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking plateform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite including cutting, etc and screed bed with CM (1:4) 20mm thick laying floor tiles complete all as specified and as directed by Engr-in-Charge.
M&L for 75mm thick PCC 1:4:8 type B 2 (using 40mm graded stone aggregate) as in sub base of floors/ pavings etc complete all as specified and as directed by Engr-in-Charge.
M&L Machine cut pre polished Kota stone slab flooring 20-25 mm thick over 20mm thick cement screed bed or bedding layer in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed by Engr-in-Charge.
Dismantling water tank of any descritpion exceeding 250 & not exceeding 500 litre and removing to store complete al las specified and directed by Engr-in-Charge.
Rotational moulded polyethylene water storage tank, inner and out white, three layers, ISI marked (cylinderical vertical with closed top) hoisted with threaded cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, including taking down of old broken water tank complete all as specified and as directed by Engr-in-Charge.Make as per PS.
S&F in 25 mm bore, fancy type Stop valve/cock, cast copper alloy, screwed down, high pressure with handle, chromium plated, screwed end for iron pipe or for union and fixed, complete all as specified by Engr-in-Charge.
S&F 25 mm bore ball brass valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule complete all as specified and directed by Engr-in-Charge.
S&F in 15mm bore, chromimum plated brass, Bib tap screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge.
Taking up or down 15 mm bore steel tubing and connections and set aside for re-use or removal to store complete all as specified and directed by Engr-in-Charge.
Taking up or down 25/32 mm bore steel tubing and connections and set aside for re-use or removal to store complete all as specified and directed by Engr-in-Charge.
S&F 15 mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd
S&F 25 mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd
S&F sinks stainless steel with drainage board made of 1.0 mm thick kitchen or laboratory with plugs, washers and wastes; including fixing contilever brackets and connecting union to pipe overall size 495mm x 420 mmmm bowl size 410mm x 330mm x 160mm, complete all as specified. Make : NIRALI/NEELKANTH/JAYNA/SILVERSHINE/JINDAL
S & F in repairs, 40mm waste coupling of PTMT for sink and wash hand basin (Half or full threaded ) (Minimum Weight 45 grams) complete all as specified and directed by Engr-in-Charge.
M&L for 100 mm thick PCC 1:2:4 ype B-1 using 20mm graded crushed stone aggregate as in floor finishes surface even and smooth without using extra cement complete all as specified by Engr-in-Charge.
M&L for 75 mm thick Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base, complete all as specified and as directed by Engineer-in-Charge.
M&L for Chequred cement concrete tiles (glazed) 30cm X 30cm X 20mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments .Layed over 20mm thick cement screed base (1:6) and all as directed by Engr-in - charge.
S&F MS Rolled sections in main and cross beams,hip and jack rafters ;purlins where connected to common rafters running rails and guids for sliding doors ;fixed with angle cleats or other connecting plates and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed by Engr-in-Charge.
Prepainted colored trapezoidal profiled/corrugated Galvalume/ Zinc coated steel sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy mettalic coating 550 MPA yield stress as per AS-1397), as in roof covering/cladding to wall fixed with self tapping screws colour/exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling/self-tapping fastener (12-14 x 55 with EPDM seals) indlucing dismantling palin or corrugated sheeting any gauge thickness including nanital or similar pattern complete all as specified and directed by Engr-in-Charge Make : Tata Blue Scope Steel Ltd/JSW Steel Ltd/CRIL oe equivalant manke in PS.
Ditto all as item No. 68 (Galvalume sheet) above but except sheeting any thickness complete all as specified and directed by Engr-in-Charge.
Prepainted colored plain Galvalume/ Zinc coated steel sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy mettalic coating 550 MPA yield stress as per AS-1397), as in roof covering/cladding to wall fixed with self tapping screws colour/exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling/self-tapping fastener (12-14 x 55 with EPDM seals) indlucing dismantling palin or corrugated sheeting any gauge thickness including nanital or similar pattern complete all as specified and directed by Engr-in-Charge Make : Tata Blue Scope Steel Ltd/JSW Steel Ltd/CRIL oe equivalant manke in PS.
M&L for preperation of new plastered wall surface of any description and applying three coats of white wash complete all as specified and as directed by Engr-in-Charge.
M&L for preperation of old plastered wall surface of any description and applying two coats of white wash complete all as specified and as directed by Engr-in-Charge.
M&L for preperation of new or previously untreated wooden surface any description of any description over 10cm in width or girth and applaying two coat of synthetic enamal paint over a coat of Pink primer complete all as specified and as directed complete all as specified and as directed by Rngr-in-Charge.
M&L for preperation of old wooden surface surface any description over 10cm in width or girth and applaying one coat of synthetic enamal paint all as specified and as directed complete all as specified and as directed by Engr-in-Charge.
M&L for preperation of new concrete /plastered surface of wall any description including 3mm thick wall care putty applaying two coat of distemper oil emulsion over a coat of primer complete all as specified and as directed complete all as specified and as directed by Engr-in-Charge.
M & L for Preparing old plasted surfaces of wall and applying two coats of distemper oil emulsion including with with complete removal of existing treatment on walls complete all as specified and directed by Engr-in-Charge.
M&L for preperation and removal of old Steel / CGI Sheet surface any description over 10cm in width or girth and applaying two coat of synthetic enamal paint complete all as specified and as directed by Engr-in-Charge.
M&L for preperation and removal of new Steel / CGI Sheet surface any description over 10cm in width or girth and applaying two coat of synthetic enamal paint over a coat or red oxide zine complete all as specified and directed by Engr-in-Charge.
M&L for two coats cement base paint on newly plastered surfaces of wall including preparation of surfaces including curing before and after applying each coat complete all as specified and directed.
M&L for two coats cement base paint on old treated surfaces of wall including preparation of surfaces including curing before and after applying each coat complete all as specified and directed.
S&F Harrison rails, 19mm dia mild steel, chromium plated curtain rods, with brackets, end bulbs, complete all as specified and as directed by Engr-in-Charge.
Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil , including spreading and levelling in layers n exc 25 cm thick complete all as specified and directed by Engr-in-Charge.
Excavating in trenches, n. exc 1.5 m wide and n.exc 1.5 m depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for laying cables/pipes, etc. n exc 10 sq m on plan in hard/dense soil and getting out soil, complete all as specified and as directed by Engineer-in-charge.
Returning filling in (soil) including spreading, levelling, watering and well ramming in layers n.exc 25cm thick in any type of soil complete all as specifed and as directed by Engineer-in-Charge.
Removal of excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specifed and as directed by Engineer-in-Charge.
M&L pre-cast cement concrete(20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block masonery not exc 10cm in width with solid block masonery with solid blocks, and setting in cement mortar 1:6 all as Specified by Engr-in-Charge.
M&L for use & waset of form work for rough finished to sides and soffits of suspended slabs such as roof, floor slabs, beams, roof beams, horizontal concrete surfaces complete all as specified and directed by Engr-in-Charge.
M&L for 40 mm thick cement concrete 1:2:4 type B-0 as in damp proof course horizontal or vertical surfaces including with water proofing compound @ 200 ml per bag of cement with necessary formwork if required complete all as specified and directed by Engr-in-Charge.
M&L for Reinforced cement concrete M-30 (design mix) in Beams, cantilivers, bressummers, lintel over 1.5 mtr span complete all as specified and directed by Engr-in-Charge.
S&F mild steel TMT bars of 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips , complete all as specified and directed by Engr-in-Charge.
All as per item No. 90 here-in- before but up to and including 6 to 8 mm dia in stirrups, spacers and binders as in columns and beams etc. as specified and directed by Engr-in-Charge.
M&L for hard core of broken stone or boulders of gauge n.exc 63 mm deposited, spread and level in layers n. exc. 15 cm thick watered and rammed to true surface complete all as specified and directed by Engr-in-Charge.
M&L for 75mm PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in sub base of floor all as specified by Engr-in-Charge.
M&L for 75mm thick PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection and finished concrete surface even and smooth without using extra cement including making proper joints with bitumen mastic with sand as per specification at an interval of 3m and change of direction complete all as specified and as directed by Engr-in-Charge.
M&L for Mild Steel Bands, nut abd bolts, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engr-in-Charge.
M & L for providing and fixing Gypsum boards 12 mm thick in ceilings fixed with screws as per manufacturers instructions including anodised aluminium snap grid frame work of size 605 x 605 mm with anodised aluminium channel supports/ angles/ 'T' (Main tee 35 x 25 x 1.5 mm, cross tee 25 x 25 x 1.4 mm and wall angle 32 x 32 x 2 mm) fixed with screws/ plugs etc including GI suspenders of 6mm dia upto 1200 mm length adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size as per approved pattern and design complete all as specified and directed by Engr-in-Charge.
M&L for 75 mm bore, PVC (SWR) pipes, pressure rating 6 kg/sqcm, single or double socketed, in any length with rubber ring joints, fixed to walls, laid in trenches or in floors complete all as specified and as directed by Engr-in- Charge. MAKE: SUPREME/ASHIRWAD/FINOLEX/ SFMC/ASTRAL
M&L for 110 mm bore, PVC (SWR) pipes, pressure rating 6 kg/sqcm, single or double socketed, in any length with rubber ring joints, fixed to walls, laid in trenches or in floors complete all as specified and as directed by Engr-in- Charge. MAKE: SUPREME/ASHIRWAD/FINOLEX/ SFMC/ASTRAL
S&F PVC (SWR) Floor tap 100/110mm bore compele all as specified and directed by Engr-in-Charge.
S&F PVC (SWR) bents 110 mm bore complete all as specified and directed by Engr-in-Charge.
S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed by Engr-in-Charge.
Stack clamps made out of 50 x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore pipe, complete all as specified and as directed by Engineer-in-Charge.
S&F Vitreous china water closet, 'Orissa' pattern, including lime concrete bedding, size 580 x 440 mm white with integral foot rests excluding flushing cistern and flush pipe but including connection to trap, anti syphonage pipe etc. incl bedding with PCC 1:2:4 type B-1 using 20 mm grade stone aggregate complete all as specified and as directed by Engr-in-Charge. Make: Cera/Hindware/Parryware
S&F sand cast iron 'P' or 'S' trap 100 mm bore for indian type WC complete all as specified and directed.
S&F Vitreous China bowl urinal flat back, half stall type white (minimum), with grating and union for discharge pipe, waste coupling complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement;, flush pipe, grating and Union for discharge pipe complete all as specified and directed by Engr-in-Charge. Make: Cera/Hindware/Parryware
S&F Viterous china wash basin, white flat back size 580x 450mm including waste coupling CP 32mm dia and CI brackets of iron 65 x 65 x 6mm embedded in PCC block with PCC 1:2:4 type B-1 and PVC waste pipe 32mm dia & CP grating with holes fixed complete, all as specified and as directed by Engr-in-Charge. MAKE: CERA/HINDWARE/PARRYWARE
S&F 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with twin flush provision, complete, all as specified and as directed by Engr-in-Charge. MAKE: Cera Model Combiflush twin flush as per Cat Part No. B1020101 (Old Cat Part No 2603) or equivalent in HINDWARE/PARRYWARE
S&F 32 mm dia waste coupling of PTMT (half or full thread ) 45 grms per each complete all as specified and directed by Engr-in-Charge.
S&F 40 mm dia waste coupling of PTMT (half or full thread ) 45 grms per each complete all as specified and directed by Engr-in-Charge.
S&F soap dish chrome finish stainless steel complete all as specified and directed by Engr-in-Charge.
S&F 600 mm x 450 mm mirror of thickness 5/5.5mm of slected quality glass, mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed by Engr-in-Charge. MAKE: SAINT GOBAIN/MODI GUARD/TRIVENI FLOAT GLASS
S&F 20mm bore chromium plated, fancy type Stop valve/cock, cast copper alloy, screwed down, high pressure with handle, chromium plated, screwed end for iron pipe or for union and fixed, complete all as specified by Engr-in-Charge. MAKE: PARKO/MARC/ESS ESS/CERA
S&F 20 mm bore chromium plated, fancy type angle valve, cast copper alloy, screwed down, high pressure with handle, chromium plated, screwed end for iron pipe or for union and fixed, suitable for complete all as specified by Engr-in-Charge. MAKE: PARKO/MARC/ESS ESS/CERA
S&F PVC connections 15 mm size with PTMT nuts of length 600 mm, long complete all as specified and diected by Engr-in-Charge. Make: Prayag/Polytuf/Supreme
S&F 15mm bore, piller tap chromimum plated fancy type high pressure with or without letter Hot or cold with long screwed shank and fly nuts screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge. MAKE: PARYAG/POLYTUF/SUPREME
S&F 20 mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd
Excavating over areas, n exc 1.5 m deep and getting out hard/dense soil complete all as specified and directed by Engr-in-Charge.
Excavating over areas, exc 1.5 m but not exc 3.00 m deep and getting out hard/dense soil complete all as specified and directed by Engr-in-Charge.
M&L for Walling of random rubble, uncoursed stone masonary, well bonded, laid dry in retaining wall, abutment and similar work complete all specified and as directed by Engr-in-Charge.
M&L for Walling of random rubble, uncoursed stone masonary, well bonded, as in retaining wall, abutment and similar work built in cement mortar 1.:6 complete all specified and as directed by Engr-in-Charge.
M&L for Providing, cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregates) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, bed blocks for hold fasts, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified and directed by Engineer-in-Charge.
M&L for use & waste of form work to edges of concrete rough finished not exc 20 cm thick complete all as specified and directed.
M&L Reinforced cement concrete (Nominal mix) 1:2:4 type B1, (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and as directed by Engineer-in-Charge.
M&L for precast cement concrete type 1:2:4 (20 mm graded aggregate) as in landings, cover slab for manholes, chulla hoods, chajja, water troughs, sheleves and similar articles with plain faces, setting in CM 1:6 complete all as specified and directed by Engr-in-Charge
Material and labour for Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 for 150 mm bore pipes including S&F 150 mm dia PVC SWR pipes single socketed in any length complete all as specified and directed by Engr-in-Charge.
M&L broken stone for loose filling of guage 80mm to 150 mm graded for soak wells complete all as specified and directed by Engr-in-Charge.
Taking down carefully copper/Aluminum point wiring (Light, Fan, Socket or power) complete fitting such as switches, ceiling, regulator, sockets etc removing materials to be store for keeping in safe custody for taking credit and making good disturbed surfaces of walls, floors etc complete all as speciifed and directed by Engr-in-Charge
Taking down of old sub main wirings at any description complete all as specified and directed by Engineer-in-Charge.
M&L for point wiring for one light point or fan point controlled by one light/exhaust fan controlled by one way switch with PVC insulated copper conductor stranded cable of size 1.5 sqmm and including PVC casing/caping terminated in existing sunk CI/pressed steel terminal boxes for fixing and 1.5 sqmm PVC insulated copper wire as earth wire connected to earth wire connected to earth folly and 3.0mm thick plastic laminated sheet cover all as specified and directed by Engr-in-Charge.
All as per item No 129.00 here-in-before but 1.5 Sqmm for one 3 pin 6 Amps socket outlet including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly on the same board complete all as specified and directed by Engr-in-Charge.
All as per item No 129.00 here-in-before but 1.5 Sqmm for one 3 pin 6 amps socket outlet including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly on the independent board complete all as specified and directed by Engr-in-Charge.
All as per item No.129 above but using cable 4 Sqmm complete all as specified and directed by Engr-in-Charge
S&F in replacement for lamp holder PVC/Poly corbonate type insulated body with back plate suitable for batten fittings as specified and directed by Engr-in-Charge.
S&F in replacement for switch piano flush type one way single pole 5/6 Amp 240 volts complete all as specified and directed by Engr-inCharge.
S&Fin replacement for switch socket combination 2 in 1, 5 pin, 5/6 Amps flush type universal complete all as specified and directed by Engr-in-Charge.
S&Fin replacement for switch socket combination mulit purpose 2 in 1, 5 pin, 6 Amps and 16 Amps 230 V flush type universal complete all as specified and directed by Engr-in-Charge.
S&F in replacement for ceiling rose surface bakelite 65x50 mm two to three terminals complete all as specified and directed by Engr-in-charge.
Supply and fixing in replacement for MCB distribution board Double door, regal grey, sheet metal enclosure, SPN 240 volts 4 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc . Make: Cat part No 5076 11 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32) or equivalant make in PS.
Supply and fixing in replacement for MCB SPN 40 Amps, 'C' series, 240 V A/C complete all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4085 96 of Legrand (DX³) or equal approved in Schneider (Acti-9)/ Siemens (Betagard-5SL4)
Supply and fixing MCB SPN 6 to 32 Amps, 'C' series, 230 V A/C complete all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4086 09 to 4086 17 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)
Sub main wiring with two run of 6.00 Sqmm (2x6 sqmm) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC casing caping ISI marked with all accessories etc with one run of 6.00 Sqmm (1x6sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces including taking down of old sub main wirings complete all as specified and directed by Engineer-in-Charge. Note:- 2 runs of 6 Sqmm (2x6sqmm), one run of 6 Sqmm (1x6 sqmm) cable and one metre of PVC casing caping will be measured as one unit. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB
S&F in replacement for LED lights fitting, TITANIA SLEEK NEW T5 LED TUBELIGHT (DOUBLE SIDE CONNECTION) (Double side Connection), 1x20 watt, 220 volts, AC ultra bright LED tube light with aluminium heat sink & polycarbonate diffuser having high efficacy suited for installation in existing T5 fitting with G5 lamp holders, led driver outside decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make as per PS.
S&F in replacement for LED bulk head light fitting 1x9/10 watt 230 volt attractive wall/ceiling mounted any type with white reflactor complete with all accessories pre-wired and including connecting up with 3 core twisted flaxible copper conductor cable complete all as directed. Make as per PS.
Supply and fixing of exhaust fan, PVC body, AC single phase 230 volts of size 380 mm sweep with blades and frame and louvers complete all as specified and as directed.
S&F in lamp holder PVC/Poly corbonate type insulated body with back plate suitable for batten fittings as specified and directed by Engr-in-Charge.
S&F in switch piano flush type one way single pole 5/6 Amp 240 volts complete all as specified and directed by Engr-inCharge.
S&F in switch socket combination 2 in 1, 5 pin, 5/6 Amps flush type universal complete all as specified and directed by Engr-in-Charge.
S&F in switch socket combination mulit purpose 2 in 1, 5 pin, 6 Amps and 16 Amps 230 V flush type universal complete all as specified and directed by Engr-in-Charge.
S&F in ceiling rose surface bakelite 65x50 mm two to three terminals complete all as specified and directed by Engr-in-charge.
Supply and fixing in MCB distribution board Double door, regal grey, sheet metal enclosure, SPN 240 volts 4 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc . Make: Cat part No 5076 11 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32) or equivalant make in PS.
Supply and fixing in MCB SPN 40 to 63 Amps, 'C' series, 240 V A/C complete all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4085 96 of Legrand (DX³) or equal approved in Schneider (Acti-9)/ Siemens (Betagard-5SL4)
Supply and fixing MCB SPN 6 to 32 Amps, 'C' series, 230 V A/C complete all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4086 09 to 4086 17 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)
S&F in replacement for LED lights fitting, 1x16 watt, 220 volts, AC ultra bright LED tube light with aluminium heat sink & polycarbonate diffuser having high efficacy suited for installation of lamp holders, led driver outside decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make as per PS.
S&F 1100 V grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of pvc tape and over all pvc sheathed in service connection suspended by insulating hangers not more than 1 mtr apart including 4 mm suspension wire one twin core cable flat of stranded multistrand conductor size 10 sqmm 02 core complete all as specified and directed by Engr-in-Charge
PARIDHI CONSTRUCTION
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .