Reinvited for Renovation of Room No 341 342 343 in Pathology Deptt in Main College Building in University of Health Sciences Rohtak

Amount

Scraping cement plaster(HSR.8.32 c)

Cement concrete 1:1-1/2:3 with stone aggregate 20 mm nominal size for reinforced concrete work in shelves excluding steel reinforcement, but including centering and shuttering ,laid in position ,complete in all respects. (HSR.10.81+10.95,a)

11.43 cm thick brick wall laid in cement sand mortar 1:4 in superstructure(HSR.11.48 a)

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. The tiles should have humidity Resistance (RH) of 99", Light Reflectance ?85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 & 7) in true horizontal level suspended on interlocking T-Gird of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @ 120 gsm) comprising of main T runners of 15x32mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2mm, spaced at 1200 mm center to center along main 'T'. The system should est on periphery walls/partitions with the help of GI perimeter wall angle of size 24x24x3000mm made of 0.40 mm thick sheet, to be fixed & 40mm long dry wall S.S. screws. The exposed bottom portion of all T-section used in false ceiling support system shall be pre-painted with polyester bashed paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the Engineer-in-Charge. With or without groves (HSR 13.92)

Laying and fixing vitrified/ceramic anti skid tiles of any size of approved make in floor laid in any pattern as specified over a base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. (Tiles shall be supplied by the Department). (HSR 14.93) (Labour Rate)

Laying and fixing vitrified/ceramic/glazed tiles of any size of approved make in skirting/dado, pillars, wall facing, laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. (Tiles shall be supplied by the Department). (HSR 14.94) (Labour Rate)

Laying and fixing granite stone in all shades, 15mm to 18mm thick in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite stone (excluding the cost of granite stone) (HSR 14.96) (Labour Rate)

Preparation of plastered or concrete surfaces for painting, including sand papering the surface, applying one coat of linseed oil and filling with approved quality filler, consisting of white lead, linseed oil, varnish and chalk mitti including finishing surface to the required finish, complete (HSR 16.24) L.R

Distempering with washable oil bound distemper (of approve manufacture) two coats on old distempered work.(HSR 16.60) L.R

Steel reinforcement TMT bars FE-500 EQR / FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/storeys/basements etc. (HSR 18.22).Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. From the length so measured, the weight of reinforcement shall be calculated in tones on the basis of IS:1732.Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.

N.S ITEM

Making single nosing of Z black granite gransing polished complete (N.S)

PARVEEN CONTRACTOR