SPECIAL REPAIR TO BLDG NO P14 SUB AREA OFFRS MESS

Amount

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below and above ground level) complete all as specified and directed.

Dismantling of floor, walls tiles including bedding but not backing and rubbish off permises all as specified.

Demolition of reinforcement cement concrete above the ground floors n exc 15 cm thickness (Reinforcement cut as required to facilitate demolition) such as cooking platform, chajjas etc

Demolition of brick work built in cement mortar including all quions, arches, pillars, etc complete all as specified and directed.

Boring holes 3m deep and 300 mm dia of pile in soil for Single under reamed piles and getting out and disposal of soil to a distance of n.exc 50 m complete all as specified and directed.

Excavation in trenches in soil n.exc 1.5 m wide and n.exc 1.5m in depth for foundation, pier holes etc n exc 10 sqm on plan and getting out in any type f soil complete all as specified as directed.

M & L for plain cement concrete, 1:4:8 type D-2 Nominal Mix (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed..

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles and mass concrete complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in columns, pillars, piers, posps and struts complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m sapn and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in Chajjas and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

Use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

Use & waste of form work to rough finished flat surfaces as in soffits of suspended slabs such as roof slabs, landing and similar work not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed

Use & waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail?ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon?tal or sloping and similar work exc 10cm but n exc 20cm widerrough finished surface

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specifed and directed.

Taking down cement plaster on brick /concrete surface wall / ceiling of any description incl racking out joints hacking for key and scrubbing down with water complete all as specifed and directed.

M & L for Rendring 15mm thick in cement mortar 1:6 on fair faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L 15mm thick cement plaster on fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth (without using extra cement) complete.

M&L rendering 5 mm thick in cement mortar (1:3) on ceiling finished surface even and smooth without using extra cement, complete all as specified and directed.

Supply only water proofing compound (liquid), ISI marked.

M&L for hard core of broken bricks gauge not exceeding 63 mm deposited, spread and levelled in layers not exceeding 15 cm thick watered and well rammed to a true surface complete as specified and directed.

M&L 100 mm thick cement concrete (1:4:8), type D-2 using 40 mm graded stone aggregate as in sub base including finishing the surface rough & even for receiving kota/tiles complete.

M&L for Coloured glazed ceramic tiles (450 x 300)x 6 to 7mm thick on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white or colored cement to match complete including 10 mm thick rendering on fair faces of brick work or concrete surfaces, in cement mortar 1:4 all as specified and directed for shade, pattern and laying of tiles complete all as specified and directed.

M & L for Non skid ceramic colour tiles (square / rectangular) of 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exc. 0.18sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15 mm thick screed bed (1:6) etc complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance exc. 50 m but not exc. 25 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M&L for 18 to 20 mm thick granite slab (of any type) work (table rubbed and polished) in cooking platforms, steps, window cills, incl edge moulding & cutting holes for gas pipe through drill machine and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F PVC (SWR) bends any radius of 110 mm dia complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall & concrete and applying 2 mm thick wall care putty including preparation complete all as specified and as directed

M&L for applying two coats of oil bound distemper on wall or concrete over a coat of primer on newly prepared surfaces including, rubbing with sand paper complete.

M&L for applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared (old treated surface) surfaces including, rubbing with sand paper complete.

M&L sand filling under floors laid in layers n. exc 15cm thick spread ,levelled and rammed including watering all as specified and as directed.

M&L for applying two coats of oil bound distemper on ceiling over a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed.

M&L for two coats of weather coat paint (apex) on new plastered surfaces of wall including preparatioin plastered surfaces complete all as specified and directed by Engr-in-Charge. (Make: asian, Durolex or equivalent)

M&L for two coats of weather coat paint (apex) on old surfaces on wall including preparation of Old & plastered surfaces complete all as specified and directed (Make: asian, Durolex or equivalent)

M & L for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, confirming to Fe-290(Gde E?165 braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/shape, made by table vibratory methopd using PU mould, laid in required colour pattern over and inclujding 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed by Engineer-in-Charge.

Dismantling wall and ceiling board (fiber, pulp, PVC, insulation etc) or insulation boards / slabs / blankets, any thickness including cover fillets complete all as specified and directed.

S & F for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre, size of grid 605mm x 605mm complete all as specified and directed

S & F for hangers 6 mm dia GI (upto 1200mm length adjusting level fixed to roof/slabs by means of ceiling cleats made out of GI flat 40X3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed

M & L for 6 mm thick Non asbestos fibre cement building boards fixed or laid / inserted to timber / GI / Aluminium framework with screws complete all as specified and directed. Make- Armstrong,or everest

S&F in repair Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

Supply & Fixing of teak wood wall panelling over 12mm Waterproof Ply board, fitted to GI Framework. GI Frame work to include channels & Perimeters; fastened to the wall using SS Screws with Asian Mellamine, using compressor [Brand: Greenply] or equivalentof Kit ply

M & L for 2nd class Hard wood as in plain fillets, square, rectangular, traingular in section clean sawn secured with nails or brads of sectional area exc 13Sqcm but not exc 25 Sq cm complete all as specified and directed

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed.

All as per above item No 51.00 but exc 1.5 Sqm but n.exc. 4 Sqm each complete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specifed and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, & kitchen cupboard shutters with particle board core 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specified and directed.. Make approved by GE..

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors omplete all as specified and directed.

M&L At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified & directed.

M&L for 10mm thick Dark shade/Double charged vitrified ceramic tiles in floors, exceeding 0.42 sqm but not exceeding 1.00 sqm set & jointed in neat cement slurry and pointed in coloured cement to match including screed bed or bedding layer of 15mm thick in CM 1:6, complete all as specified & directed.

M&L for 10mm thick Dark shade/Double charged vitrified ceramic tiles exceeding 0.42 sqm but not exceeding1.00 sqm in vertical surface such as skirtings, dados etc, with and including over 10mm thick rendering in cement mortar (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement complete.

M & L 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded stone aggregate as in floors including finishing the surface rough for laying finishes complete all as specified and directed.

S & F 100 mm size Butt hinges extruded aluminum alloy with mild steel hinge pin bright polish complete all as specified and directed.

S&F Aluminium alloy sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing bolt with of extruded sections complete all as specified and directed.

M & L double action floor spring for aluminium doors hydraulically regulated made up of minimum 1.5 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including necessary cutting & making good to floor as per existing complete all as specified and directed. Make - Kelwyn / Amar

S&F 200mm long aluminum anodised barrel tower bolts of extruded section as specified.

S & F aluminium handles of extruded section, fabricated type anodised finish and fixed 150 mm long complete all as specified and directed.

S&F floor door stopper 140 mm overall length of cover plate of aluminium alloy body and tongue, anodised. With hard drawn spring, fixed in floor complete as directed by Engr-in-charge

S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified.

Hacking out old boken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with oil putty or fixed with beads complete.

S& F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified and directed.

S& F 4.8 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 Sqm in each pane complete all as specified and directed.

S & F 3 mm thick figured glass pin head type and glazing with oil putty in squares n exc 0.5 Sqm in each pane etc complete all as specified and directed.

S&F in repair 18/19 mm thick Block boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on one face, including teak wood lipping, 6 mm thick on sides complete for cupboard shutter and incl shelves all as specified and directed

S&F 100 mm long hasp & staple aluminium anodised wire type, incl bolt to hinge plate and fixed with screw complete.

S&F in repair stainless steel designer curtain rod fancy type curten rod 20 mm dia as approved complete..

Sypply and fixing Toughned glass 12mm thick as in Glass door, hinged doors and similar work including cutting to shape, drilling holes required, Grinding, polishing and rounding off edges of glass including necessary fixing fittings which required to holding the door complete all as specified and directed.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge

S&F Centre hole basin mixer with popup waste system with 450mm long braided hoses complete all as specified. Make : Jaquar Cat Part No COP-169BPM and equivalent in Prayag Polymers Pvt Ltd

S&F Wall Mixer 3-in-1 System with Provision for both Hand Shower and Overhead Shower Complete with 115mm Long Bend Pipe, Connecting Legs & Wall Flange (without Hand & Overhead Shower complete all as specified. Make : Jaquar Cat Part No COP-281PM and equivalent in Prayag Polymers Pvt Ltd

S&F vitreous china Counter Top Basin of Size: 500x435x180 mm including waste pipe complete all as specified and directed. Make Jaquar Cat Part No KUS-WHT-35601 or equivalent in Prayag Polymers Pvt Ltd

S & F Vitreous china wash down water closet pan ( pedestal pattern ) Rimless Bowl With Cistern For Coupled WC With UF Soft Close Slim Seat Cover, Hinges, Conversion Bend, Dual Flush Cistern Fitting, Fixing Accessories And Accessories Set, Size: 390x645x845 mm, S Trap- 250 mm (With Conversion Bend) complete all as specified and directed Make : Jaquar Cat part No ONS-WHT-10753NS250UFSMZ or equivalent in Prayag Polymers Pvt Ltd or cers Ist quality

S&F chromium plated Hand Shower (Health Faucet) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook suitable for EWC including nut/washer complete. Make : Jaquar Cat part No ALD 573 or equivalent in Prayag Polymers Pvt Ltd.

S&F in repairs PVC connection 15mm dia size and 450 mm long with 2 Nos brass check nuts its washers complete all as specified and as directed.

S&F in repair bib tap 15mm brass chromium plated long body with crutch butterfly handle, screw down screwed for iron pipe or for brass ferrule etc complete all as specified and directed.

S&F towel rack 600mm long with lower hanger stainless steel including fixing arrangements complete. Make : Jaguar Cat part No CPA 1181 or equivalent.Prayag Polymers Pvt Ltd

S&F in repair 15 mm bore concealed type stop valves, cast copper alloy, screwed down, high pressure, with capstan head, fancy type, chromium plated, with long shank and cup, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F Angular Stop Cock with Wall Flange angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe. Make Jaquar Cat Part No COP-057PM or equivalent Prayag Polymers Pvt Ltd

S&F CP two way angle valve with wall flanges 15 mm bore, screwed down, screwed for iron pipe or for brass ferrule complete. Make Jaquar Cat Part No COP-041PM or equivalent in Prayag Polymers Pvt Ltd

S&F glass shelf 600mm (with brass brackets) including fixing arrangements complete. Make- Jaquar Cat part No CPA-1171or equivalent

S&F of stainless steel Soap Dispenser with Glass Bottle of standard size and shape complete. Make- Jaquar Cat part No CPA-1135 or equivalent in Prayag Polymers Pvt Ltd.

S&F Overhead Shower 120X120mm Square Shape Single Flow(Face Plate Stainless Steel & ABS Body in Chrome finish) with Rubit Cleaning System with CP arms 300 mm long complete all as specified and directed. Make- Jaquar Cat part No OHS-1667 or equivalent in Prayag Polymers Pvt Ltd

S&F in repair plastic water closet seat cover, Cream / white colour, closed pattern with flat bottom and cover and mild steel chromium plated aluminium hinging device for pedestral pattern WC complete all as specified and directed.

S&F toilet Paper Holder with Flap Recessed Type (Stainless Steel) complete all as specified and directed. Make- Jaquar Cat part No AHS-1553 or equivalent in Prayag Polymers Pvt Ltd

S&F PVC (SWR) nahani/ floor trap, plain with grating with or without waste hole including jointing with solvent cement 75mm dia etc complete

Dismantling water tanks of capacity exc 500 and n exc 1000 ltrs complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered hoisted and fixed in position all as specified in SSR Pt-I 1000 Ltr capacity including CP tank nipple complete all as specified and directed.

M&L Preparing old wooden surfaces exceeding 10Cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L Preparing old steel surfaces exceeding 10Cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F 1.80 mm thick powder coated aluminium window/ ventilator section fixed type with frames including 5.0 mm thick tinted /frosted glass, standard rubber gasket, aluminium beadings, joining cleat for fixing, locking devices complete all as specified & directed. Make : Jindal/Hindalco or Equivalent

S&F Tubes, ‘medium grade’ galvanized, with all GI fittings and fixed complete to walls and ceilings or laid in floors of 15 mm dia including cutting /chasing in walls etc. including taking up or down steel tubing and connections complete all as specified and as directed

S&F Tubes, ‘medium grade’ galvanized, with all GI fittings and fixed complete to walls and ceilings or laid in floors of 20 mm dia including cutting /chasing in walls etc. including taking up or down steel tubing and connections complete all as specified and as directed

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete.

S&F in repair Door closer hydraulically regulated castiron body, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as spfd & directed.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLS cable 1100 volts grade ISI marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly all as specified and directed for the following :-

(a) One light/ fan point controlled by one, one way switch 5 Amps

(b) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

(c) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(d) One bell point controlled by one, bell switch 5 Amps

Description all as per item No 104 here in before but using 2.5 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

Description all as per item No. 104 here in before but using 4.0 sq mm single core copper conductor FRLS cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 4.0 sq mm PVC insulated copper conductor FRLS cable as earth continuity conductor along with wiring and connecting to the common eath dolly. (for AC Point)

S & F for Modular Switch piano flush type, single pole, one way, and 5/6 Amp single module complete all as specified.

S & F for Modular Switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified.

S & F for Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for Modular Switch Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

S & F for for Bell push modular 6 Amps single module complete all as specified.

S & F for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

S & F for Modular type TV Socket out let complete all as specified and as directed.

S & F for Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified

Supply and fixing in repair white finished single mounting modular plates with inner & outer cover suitable for housing modular accessories suitable for one module box complete all as specified and directed

All as per item no 120 above but suitable for 2 modules

All as per item no 120 above but suitable for 3 modules

All as per item no 120 above but suitable for 4 modules

All as per item no 120 above but suitable for 6 modules

All as per item no 120 above but suitable for 8 modules

S&F sheet metal boxes concealed in wall suitable for housing modular accessories for 1 or 2 modules complete all as specified and directed.

S&F sheet metal boxes concealed in wall suitable for housing modular accessories for 3 modules complete all as specified and directed.

S&F sheet metal boxes concealed in wall suitable for housing modular accessories for 4 modules complete all as specified and directed.

S&F sheet metal boxes concealed in wall suitable for housing modular accessories for 6/8 modules complete all as specified and directed.

S & F for Modular blanker in suitable size as per site requirement complete all as specified and as directed.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with multi stranded copper conductor of size 2.5 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 2.5 Sqmm (nominal area) multi stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 2.5 sqmm cable,one run of 2.5 sqmm cable and one run of PVC conduit will be measured as one unit

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with multi stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) multi stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit

M & L for Sub main wiring with approved colour coding as per IS with four single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Four runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit

S & F for sheet metal enclosure MCB DB TPN 4 way Vertical type with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCB tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed

Supply and fixing of LED COB light of 7/12 Watts in recessed ceiling mounted , high transmissitivity diffuser, high lumen ouput , 230 volts including electronic driver connector etc complete with all accessories internally pre wired and necessary mounting arrangements, from ceiling rose to fitting complete all as specified and as directed. Make :- Bajaj,Philips, Havells,CG.

Supply and fixing of fancy LED mirror light of 7 Watts in wall mouning , for picture spot light with high transmissitivity diffuser, high lumen ouput , 230 volts including electronic driver connector etc complete with all accessories internally pre wired and necessary mounting arrangements, from ceiling rose to fitting complete all as specified and as directed. Make :- Bajaj,Philips, Havells,CG.

S & F for PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 20 mm dia for LAN, telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed.

Taking down carefully copper / aluminium point wiring (light, fan, switch,socket or power, Bell & Two way point) complete with fitting such as switches, sockets, ceiling rose,sketch light fittings etc, and making good the disturbed surface of walls and floors etc complete all as specified and directed.

Taking down carefully main switches DB's/ MCB DB's and making good the disturbed surfaces of walls etc complete all as specified and directed.

Taking down carefully copper / aluminium sub main wiring including teak wood batten / conduit and making good the disturbed surface of walls as directed.

HARINANDAN RAI SONS

RAJ AND SONS

SINHA CONSTRUCTION

M/S SAROJ KUMAR SINGH

M/S ANAND MOHAN ENTERPRISES

M/s Mukesh and company

jaglalchoudharyandsons

Vijay Bakshi and Son