PROVISION OF TOILET BLOCK NEAR BLDG NO CB 2 TRG STORE IN ATGM AREA AND PROVISION OF CERTAIN MINOR AND REVENUE WORKS UNDER GE MIS MHOW

Amount

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/dense soil, complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation for shafts, wells, cespits, manholes pier etc and n.exc 10 Sqm on plan and getting out in hard/dense soil, complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filing,sub base of floor, etc complete all as specified and directed

M & L for high strength deformed TMT steel bars 8 mm dia and over, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.90 mm dia, etc complete all as specified and directed.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia as in strriups, spaces and binders complete all as specified and directed.

M & L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, finished fair complete all as specified and directed

M&L for RCC M25 (Design Mix) grade concrete using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed Note : - Reinforcement shall be measured and paid separately under relevant item.

Returing, filling in trenches, including spreading, levelling, watering and well ramming in layers not exc 25 Cm in hard/dense soil complete all as specified and directed.

M&L for sand filling under floor including watering and consolidaion complete all as specified and directed.

Removing excavated material (soil) to a distance not. exc. 50 meter and depositing where directed at a level n.exc 1.5 m above the starting point.

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions finished fair complete all as specified and directed

M&L for RCC M25 (Design Mix) grade concrete using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified and directed. Note : - Reinforcement shall be measured and paid separately under relevant item.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc. 6.00m mean radius built in cement mortor 1:6., etc complete all as specified and directed.

M & L for brick work with sub class 'B' modular bricks, straight or curved on plan to any radius built in CM 1:4 in half brick thick walls complete all as specified and directed.

M & L for use and waste of formwork to sides and soffits of floor or roof beam, beam hauchings, bands, girders, bressummers, lintels, etc for fair finished surface complete all as specified and directed

M&L for RCC M-25 (design mix) grade concrete using 20 mm graded stone aggregate as in beams, bands, cantilvers, bressummers, lintel, plinth beam, chajjas etc over 1.5m span complete all as specified and directed Note : - Reinforcement shall be measured and paid separately under relevant item.

M & L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizontal or sloping) for fair finished surface complete all as specified and directed.

M & L for use and waste of timber formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M&L for RCC M-25 (Design Mix) grade concrete using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, etc complete all as specified and directed Note : - Reinforcement shall be measured and paid separately under relevant item.

M&L for moorum / red bajri filling in floors or pavings, laid in layers n.exc 15cm thick, spread, levelled and rammed including watering and consolidation complete all as specified and directed.

M&L for hardcore of gauge n exc. 63 mm, with broken stone boulders deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B0, using 12.5 mm graded aggregate for levelling course in floors complete all as specified and directed.

M & L for 75mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in floor/ plinth protection finish the surface even and smooth with using extra cement including filling the expansion joints with bitumen filler / filler boards and necessary form work etc complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:6 on other than fair faces of brick work or concrete surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick or concrete surface mixed with liquid water proofing compound @ 200 ml per 50 Kg of cement bag finished even and fair without using extra cement complete all as specified and directed. Note:- Liquid water proofing compound shall be measured and paid separately under relevent item

M&L for rendering 5mm thick in CM 1:4 as in ceiling on concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and as directed.

S&F fabricating coloured powder coated aluminium frame work,door shutter ,windows , ventilators, partition with one or more rebates sections of approved tint as required for partions including beading,cleat, screws,fasteners, plugs, for fixing with wall/ceiling columns/beams etc complete all as specified and directed.

S&F aluminium coloured power coated window and ventilator shutters, sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary locking arrangement, guide wheels, jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed. Note : Glass shall be measured and paid separterly under relevant item.

S&F aluminium coloured power coated door shutters, aluminium section weighing 0.55 Kg/m including necesssary joining cleats, glazing clips, rubber neoprene packing handles 2 Nos in each door, pad lock, hinges, anodised aluminium snap beading, screws,tower bolt and Door Bolt etc complete all as specified and directed. Note : Glass shall be measured and paid separterly under relevant item

S&F 4.8 mm thick plain or tinted glass, ordinary quality including rubber gasket for packing and fixed to aluminium doors/window/partition including necessary cutting / moulding and chamferrring of edges as in service window/counters complete all as specified and directed.

S&F aluminium (extructed section) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutter and fixed complete all as specified and directed.

M & L for applying two coats of first quality oil emulsion distember over newely prepared surface of wall finished with putty complete all as specified and directed. Note:- Putty shall be measured and paid seperately under Ser Item No. 37

M & L for preparation of new plastered surfaces of walls and applying two coat of Acrylic Smooth exterior paint of required shade (@ 1.67 litre/10 sqm) over a coat of primer(@ 2.20 kg/10 sqm) of same make , over a coat of putty all as specified and directed. Note:- Putty shall be measured and paid seperately under Ser Item No. 37 Make : Asian- Apex or other Equivalent as approved by GE.

M&L for preparation of newly plastered surface of wall and applying 2mm thick, cement base wall care putty in two coat (each coat not less than 1mm) over a coat of primer on wall, finished even and smooth with sand payer complete all as specified and directed

M&L for non –skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 15mm thick screed bed in CM 1: 6 complete all as specified and directed.

All as per item No 38 here-in-before but as in skirting/ dado etc with and including 10mm thick backing coat in cement mortar 1:4 on wall complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size not less than 450x300x7 mm thick as in vertical surfaces such as dado ,skirting etc set and jointed in neat cement slurry and pointed with coloured cement to match colour of tile over and including 10 mm thick backing coat on fair faces of brick work in CM (1:4) complete all as specified and as directed.

M&L for 18-20 mm thick Black granite slab of approved quality of any size bedded and jointed in grey cement slurry and pointed with white cement mixed with admixture of pigment to match the shade of granite stone laid over and including 15 mm thick screed bed in CM (1:4) including necessary polishing by using mechanical grinder and moulding edges complete all as specified and directed.

M&L for 60mm thick machine pressed precast concrete interlocking paver block rubber moulded (glossy finish) of M-35 grade of approved shape, size and colour conforming to IS 15658-2006 and including joints filled with sand and 30mm thick stone dust bedding as a leveling course complete all as specified and as directed.

M & L for rendering 10mm thick in cement mortar 1:3 mixed with integral water proofing compound while concrete surface is green and finish the surface even and smooth without using extra cement all as specified and directed Note : WPC shall be measured and paid separately under respective item.

M & L for preparation of roof surfaces and applying bituminous primer (conforming to IS-3384-1965) @ 0.40 Kg/Sqm complete.

M & L for applying a tack coat of industrial bitumen grade of 85/25 at the rate of 1.2 Kg per Sqm including cleaning the surfaces (1st coat for bonding material below membrane and 2nd coat on top of membrane). Note : Each coat shall be measured and paid seperately.

M&L for 3mm thick APP based polymeric membrane minimum weighing 3kg/sqm and reinforced with polyster non wove fabric (weight not less than 150 gms/sqm) laid on primed surface by forced application complete all as per manufacturer's instruction and as directed. Note: Application of APP membrane shall be done by authorised Applicator of membrane Manufacturer.

M&L for applying two coats of bitumen based aluminium painting @ 0.15 Kg / sqm over APP mambrance including preparation of surface as on non assesible area complete all as specified and directed.

Supply only Liquid Water proofing compound PIDIPROOF LW+ of Dr FIXIT or other equivalent as approved by GE.

S& F Rotational moulded Polyethylene water storage tank 1000 litres capacity (cylidrical vertical with closed top) double layered hoisted and fixed in position all as specified in SSR part I complete all as specified and as directed.

S&F 15mm bore steel tubing medium grade ,galvanized with all fitting such as bend ,elbow, socket,tees,and fixed complete to wall or in ceiling or in floors including cutting threading and making forged bends on pipes MS hooks etc ,complete all as specified and as directed.

All as per item no 50 above but 20mm bore complete all as specified and as directed.

S&F CP pillar taps (swan neck type) cast copper alloy CP with capstan head, screwed down ,high pressure with long screwed shanks and fly nuts, fixed in 15 mm bore pipes complete all as specified and directed.Make-Plumber/Essco of jaguar(Economical Range)

S&F CP angle stop cock of 15mm bore screwed down for high pressure with crutch or butter fly handle ,screwed both end for iron pipes complete all as specified and directed .Make-Plumber/Essco of jaguar(Economical Range).

S&F fancy type chromium plated15mm bore two way Bib cock cast copper alloy with crutch or butterfly handle, screwed for iron pipe or brass ferrule etc complete all as specified and as directed. Make-Plumber/Essco of jaguar(Economical Range)

S& F CP toilet paper holder complete all as specified and as directed.

S&F vitreous china wash down water closet pedestal pattern white excluding flushing cistern and flush pipes complete all as specified and as directed .

S&F vitreous china squatting pan `Orissa ' pattern of size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipes) including connection to trap, flush pipe etc including lime concrete bedding and 'P' or 'S' trap complete all as specified and as directed.

S&F PVC valve less,syphonic action type flushing cistern,low level ,white with inlet ball valve,float and handle including brackets and connection to pipe and fixing of chain and pull or lever if any complete all as specified and directed. .Make-Plumber/Essco of jaguar(Economical Range)

S&F health faucet with flexible pipe of one metre length including wall hook for EWC complete all as specified and as directed. Make :- Plumber/Essco of jaguar(Economical Range)

S & F vitreous china wash basin white (oval shaped under counter) of size 550 x 400mm including 32mm brass CP waste coupling complete all as specified and as directed .

S&F Vitreous China Urinal, Half stall type,white with grating and union for discharge pipe, urinal spreader with waste pipe including all fittings complete all as specified and as directed

S & F PVC (SWR) floor trap of 75mm dia outlet plain or multipurpose grating including joining to waste pipe with solvent cement joint complete all as specified and as directed.

S&F PVC connection 15mm dia with PTMT nuts of length 450 mm long complete all as specified and as directed.

S&F PVC waste pipe for urinal/wash basin/ sink pipe 32mm bore, 65cm long complete all as specified and as directed.

S&F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipes and fixed. ( Minimum Weight 210 gms) complete all as specified and as directed

S&F 0.50mm thick (including coated thickness) pre-colour pre- profiled (Galvalume/zinkalume) sheets of required colour and design having tensile strength of 550 Mpa as in roof sheeting/sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and minimum 150mm end lap laid to slope all as per manufacturer / profile maker instruction complete all as specified and as directed.

S&F mild steel Hollow Section work in tubular trusses, purlins, rafter, tubular column and running rails fixed with angle cleat or other connection plates including special shaped washer etc, complete using ERW or induction butt welded tubes conforming IS-4963,1993 and IS-1161 -1979 grade ST-240 complete all as specified and as directed.

M&L for cutting into existing manhole for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round as 3/3 section) in cement concrete 1:2:4 type B1 using 20mm graded stone aggregate smoth finished and benching as required for 150 mm pipe complete all as specified and directed.

M&L for SGSW drain pipe of 150mm internal dia laid in trenches and jointed in cement mortar (1:1) complete all as specified and directed including demolition and breaking up old drain pipe of any type and any description and removing the debris including concrete bed and haunching from the trenches complete all as specified and directed.

M&L for PCC (1:4:8) type C2 using 40mm graded stone aggregate as in concrete bed to drain pipe including packing under and haunching against the sides of pipe after they are laid and tested internal dia of pipe 150mm with specified bedding thickness, etc complete all as specified and directed .

M&L for RCC 1:2:4 type B1 using 20 mm graded stone aggregate as in precast cover slab,manholes and soak well cover slab etc set in cement mortar (1:4) etc with and including necessary form works complete all as specified and directe. Note:-Reinforcement shall be measured & paid separately under relevant item.

M&L for cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as in foundations, filling and mass-concrete complete all as specified and directed.

M&L for PCC 1:2:4 type B1 using 20mm graded aggregate as in coping including necessary form work complete all as specified and as directed.

S&F PVC (SWR) pipe 110mm dia single socketed in any length with rubber ring joints laid on wall / floor complete all as specified and directed.

S&F PVC (SWR) pipe 75 mm dia single socketed in any length with rubber ring joints laid on wall / floor complete all as specified and directed..

S&F PVC ( SWR) bends any radius bore of 110 mm all as specified and directed

S&F PVC ( SWR) bends any radius bore of 75 mm all as specified and directed

S&F PVC ( SWR) junction single (single T) bore of 110 mm all as specified and directed

S&F PVC ( SWR) junction single (single T) bore of 75 mm all as specified and directed

Preparation of new steel surfaces, of any description, over 10 cm in width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide complete complete all as specified and as directed

Taking down chowkhats or frames with shutter (with out taking off shutters from the frame) area exc 1.5 sqm but n.exc 4.0 sqm each complete all as specified and as directed.

S & F galvanised Stainless steel wire cloth of 0.36mm dia wire and average width of aperture 1.4mm & fixed with tacks of stainless steel wire staples,etc complete all as specified and as directed.

S&F 200 mm long Aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) including fixing clips of sheet, cast or extruded section and fixing bolts and 16mm dia bolt sliding bolts of extruded section complete all as specified and as directed.

Taking down cement plaster on brick or concrete surfaces, parapets including raking out joint, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quions ,arcches , pillars etc complete all as specified and as directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10 mm thick in CM ( 1:6 ) on fair faces of wall/ concrete surfaces finished even and fair complete all as specified and directed.

M&L for preparation of old decorated surfaces of wall including brooming , scraping down, Smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks and applying two coats of first quality oil emulsion distemper white/coloured over a coat of cement base white wall care based putty (where it is required in Patches) all as specified and directed by Engineer-in-Charge. Note:- Putty shall be measured and paid seperately under Ser Item No. 91

M&L for preparation of old decorated surfaces of wall including brooming , scraping down. Smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks and applying two coats of Acrylic Smooth exterior paint of required shade (@ 1.67 liter/10 sqm) over a coat of primer(@ 2.20 kg/10 sqm) of same make over white cement based putty (where it is required in patches)all as specified and directed. Make Asian- Apex or other Equivalent as approved by GE Note:- Putty shall be measured and paid seperately under Srl Item No. 91

M&L for complete removal of existing treatment of wall(any no. of layers) and apply 2mm thick white cement base wall care putty in two coats (each coat not less than 1mm) over a coat of cement base primer on walls and surface finished even and smooth with sand paper complete all as specified and directed

Demolition of cement concrete in ground floor and paving not exceeding 15cm thick ( below or above ground level ) complete including removal of debries out side MD land all as specified and as directed .

M&L for PCC (1:2:4) type B0 using 12.5 mm graded crushed stone aggregate as in sub base, levelling course, etc complete all as specified and as directed.

M&L for scratch free vitrified ceramic tiles 10mm thick (square or rectangular) area of each tile not exceeding 0.36 sqm ,in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

All as per item No 94 above but as in skirting/ dado etc with and including 10mm thik backing coat in cement mortar 1:4 on wall complete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semicorrugated) sheets in roof coverings complete all as specified and as directed.

M&L for mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming IS-1161-1979 grade ST-240 complete all as specified and as directed.

M & L for Exposed metal frame ceiling with 6mm calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid Note : Frame work for ceiling shall be measured and paid separately)under relevant item complete all as specified.

S & F Anodised aluminium snap grid of size (605mmx605mm) frame work for false ceiling with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

Taking down chowkhats or frames with shutter (with out taking off shutters from the frame) area n. exc 1.5 sqm each complete all as specified and as directed.

S & F second class hard wood plain, solid straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed.

S & F 35 mm thick factory made, second class hard wood glazed and skeleton shutters open rebeated and prepared to received glass, gauzed, with out sash bar edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc, size of member of shutter as per specified in SSR Part-I Section 8, clause 8.24 (a) and for door and fixed with chowkats, chemically pressure treated complete all as specified and as directed.

S&F 35mm thick factory made second class hard wood plain, framed pannelled shutters (two Nos of panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per (IS : 1003 part-I , kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 125 mm Butt hinges medium weight cold rolled mild steel and fixed complete all as specified and directed.

S&F 150 mm long Aluminum anodized barrel tower bolts of extructed section complete all as specified and directed.

S&F aluminum alloy handles fabricated anodised of 150 mm long complete all as specified and directed. .

S&F 300 mm long Aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) including fixing clips of sheet, cast or extruded section and fixing bolts and 16mm dia bolt sliding bolts of extruded section complete all as specified and as directed.

S&F 25 mm dia mild steel chromium plated drappery curtain rod with fixing bracket complete all as specified and directed .

Preparation of new wooden surfaces of any description not other wise described, over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

Supply and fix 7 mm thick aluminium coloured power coated grill of Deco Grill pattern DG 104, fixed in aluminium windows / ventilators, etc.including necessary aluminium channels in openings of windows / ventilators, complete all as specified and as directed.

M&L for preparation of old painted wooden surfaces of any description exc 10cm in width or girth and applying one coat of synthetic enamel paint as directed and specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs/ blankets and thickness, including cover fillets at any height including prroper scaffolding arrangements complete all as specified and as directed.

M&L for chequered cement concreter tiles with gery cement and pigment of size 40cm x 40cmx 40mm thick, set and jointed and pointed in neat cement slurry in floor etc over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

Excavation in trenches n.exc 1.5m wide, depth exc 1.5m but n.exc 3.0m and getting out in hard /dense soil complete all as specified and directed.

M&L for Earth filling under floor including watering and well ramming in layers n.exc 25 cm thick complete all as specified and directed.

M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per Square metre of surface area with ATT complete all as specified and directed.

M&L for treating the back fill in contract with foundation @ 7.5 litres of emulsion per Sqm of vertical surface area with ATT complete all as specified and directed.

M&L for treating the top surface of the filled earth @ 5.00 litres of emulsion per Sqm of surface area with ATT complete all as specified and directed.

M&L for treating the soil under the plinth protection at the rate of 5 litres of emulsion per Square metre of surface area with ATTcomplete all as specified and directed.

M&L for Reinforced cement concrete Design mix (M-25) grade concrete using 20mm graded stone aggregate as in chajjas complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar 1:6 on brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed

M&L for applying two coats of exterior weather proof water base emulsion paint white /coloured over a coat of primer of same make complete all as specified and directed by Engineer-in-Charge. (Make :- Asian-ACE/Berger- Wallmasta/Nerolac-suaksha).

M&L for Preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed

M&L for Preparation of newly plastered surfaces of wall and applying three coat of white wash all as specified and directed

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in a sub base of floors complete all as specified and directed

M&L for 75mm thick, PCC 1:3:6, type C1 using 40 mm graded stone aggregate, as in plinth protection, finished fair and even complete all as specified and directed.

Material & labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including 15mm thick screed bed in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing to mirror finish, complete all as specified and directed

All as per ser item No 127 hereinbefore but on vertical surfaces as in skiting /dado of size as required at site complete all as specified and directed

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

S & F Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.,complete as specified.

Supply and fix steel window/ventilator with side hung shutters including box type friction hinges, steel handle, steel peg stay and glazing bars welded complete all as directed and specified. Note : Glass shall be measured and paid separately under relevant item

S&F Sheet glass ordinary quality 3 mm thick and glazing with oil putty or wooden beads in squares not exceeding 0.5 Sqm in each pane complete as specified and directed.

M&L for plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in hold fast, blocks complete all as specified and directed

S & F Mild steel sliding door bolt of size 250mm , stove enamelled black with bright bolt not less than 16mm dia, with and including a minimum of 6 bolts and nuts, complete all as specified and directed.

S & F Mild steel barrel tower bolt 200mm long stove enamelled black with bright bolt and fixed complete all as specified and directed

S & F Mild steel butt hinges of size 100mm medium weight cold rolled complete all as specified and directed

S & F Mild steel butt hinges of size 50mm medium weight cold rolled complete all as specified and directed

S & F mild steel pressed handle of size 125mm oval type stove enamelled black complete all as specified and directed

S & F second class hard wood small fittings such as cleats, brackets of any type, stop for door and windows etc n exc 200 Cu.cm each, complete all as specified and directed.

Schedule 'A' Part II (E/M Portin)

M & L for Point wiring with FRLS PVC insulated PVC unsheathed electric cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area drawn in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good and matching disturbed surface of wall with existing surface of wall (cutting except on ceiling for fan point only, on ceiling instead of PVC conduit surface casing caping shall be used) & 1.5 sqmm green FR LS PVC insulated unsheathed copper conductor as earth wire connected to earth dolly by providing lugs including galvanised boxes and bakelite sheet for mounting switches, sockets, fan regulators etc for for the following . Make of PVC conduit/Casing Caping:- Plaza/Finolex/Polycab/Kalinga/Jindal/Asian .

One light point controlled by one switch

One Exhaust fan point controlled by one switch

One 5Amps socket out let point controlled by one switch on same board with other switches.

One 5Amps socket out let point on independent board controlled by one switch.

All as per item No-197 here in before but using PVC insulated unsheathed 2.5 sqmm cross sectional area cable for phase /neutral & for earth 2.5 Sq mm green PVC insulated cable for 15 Amps socket point on independent board controlled by one switch.

S&F switch piano flush button single pole one way 6 Amp 240 volt complete as directed.

S&F socket outlet flush type 5 pin, 6 Amps, 230 volts complete all as directed.

S&F switch piano flush button single pole one way 15 Amp 240 volt complete as directed.

S&F socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 230 volts complete as directed.

S&F ceiling rose surface bakelite three terminal complete all as directed.

Supply and fix integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 , Bajaj cat Pt No. BCLSB 18WH or other equivalent in Wipro

Supply and fix integrated LED tube light fitting 1x9/10 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square box complete all as specified and directed .Make:- Havells Cat No. LHEXBLP7IN1W009 Bajaj Cat Pt No. BCLSB 10 WH or equivalent in Wipro

M&L for Sub main wiring with two runs of single core FR LS PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including FR LS PVC insulated unsheathed 4.0 Sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engr-in-Charge.

Supply and fix LED street light fittings 1x25 /30 Watt, 5700K complete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & IP 65 protection fixed on and including sufficient length and appropriate size GI bracket with all accessories duly connection with three core flexible copper cable complete all as specified and directed .Make:- Crompton Cat No. LSTO-25-CDL, Bajaj Cat No. ENXTP30LWHSYPCSD or other equivalent in Havells .

Supply and fix double door SPN DB 8 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed by Engineer-in-Charge.

S & F MCB SPN 6 to 32 Amps 10 KA, 'B' series including connection with suitable size aluminium / copper lugs including taking down the existing complete all as specified and directed by Engineer-in-Charge.

S&F MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' series including connection with suitable size aluminium / copper lugs including taking down the existing complete all as specified and directed by Engineer-in-Charge.

M & L for Earthing complete with galvanized steel earth plate electrode of size 60cm x 60cmx 6.3 mm thick buried directly in ground ( earth pit not less than 2.25 metre deep below ground level) with the top edge of the earth plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or of steel all as shown in electrical plate No.5 of SSR Part-I and including excavation & earth work in any type of soil , disposal of soil , providing alternate layers of charcoal and common salt, construction of PCC earth chamber in mix 1:3:6 type C1 with 40 mm thick RCC 1:2:4 type B1 cover slab reinforced with 8mm dia MS bars both ways with lift hook made out of 8 mm dia bar, watering arrangement with funnel and wiremesh and watering pipe of 20mm dia GI light grade and 15mm dia light grade pipe for earth lead protection and testing on completion, complete all as specified and directed.

Supply and fix Exhaust fan 200mm sweep, AC single phase 230 Volts, non metallic type, complete with louver including electric connection with suitable size copper conductor cable, clamps, nuts, bolts etc including making hole of appropriate size in the existing brick wall and making good the disturbed wall and matching with the existing surface of wall complete all as specified and directed by Engineer-in-Charge. Make : Havells Model: Ventil Air-DX white or other equivalent in /Bajaj/Crompton

Supply and fix Modular Switch flush type 6 Amps single pole, one way complete including taking down the existing all as specified. Make: Legrand Mylinc Series, Anchor Roma Plus, Crabtree Athena Series.

Supply and fix Modular Socket outlet, multi purpose, 2/3 Pin combined 6 Amps flush type complete including taking down the existing all as specified. Make: Legrand Mylinc Series, Anchor Roma Plus, Crabtree Athena Series.

Supply and fix Modular Socket outlet, multi purpose, 2/3 pin combined 16 Amps universal socket complete including taking down the existing all as specified. Make: Legrand Mylinc Series, Anchor Roma Plus, Crabtree Athena Series.

Supply and fix Modular Switch 16 Amps single pole, one way complete including taking down the existing all as specified. Make: Legrand Mylinc Series, Anchor Roma Plus, Crabtree Athena Series.

Supply & fix modular fan regulator step type, 2 module type complete including taking down the existing. Make: Legrand Mylinc Series, Anchor Roma Plus, Crabtree Athena Series.

Supply and fixing white finished single mounting modular plates suitable for modular accessories of following sizes including taking down the existing: Make: Legrand Mylinc Series, Anchor Roma Plus, Crabtree Athena Series

Sutable for 1/2 modules

Sutable for 3 modules

Sutable for 8 modules

Supply and fix sheet metal boxes concealed in wall suitable for housing modular accessories of following sizes including taking down the existing:- Make: Legrand Mylinc Series, Anchor Roma Plus, Crabtree Athena Series.

Sutable for 1 or 2 modules 50mm.

Sutable for 3 modules 50mm.

Sutable for 8 modules 50mm.

S&F in repairs LED ceiling light fittings 34/36 watt recess mounting type complete with driver duly connection wire etc including taking down the existing. Make, Havells Cat No. PLUTONEO2X2PLR34WLED857S, Crompton Cat No. LCTLR-36-FO-CDL

Supply & fix LED Bulk Head luminaire 10W, 6000K pressure die cast housing with IP65 protection complete with electric connection all as specified and directed by Engr-in-Charge. Make:- Havells Cat No. HEXAFT10LED857SSYMBOPC, Crompton Cat No. LBH-10-CDL, Bajaj Cat No. BIBWP 10W LED

M&L for Sub main wiring with two runs of single core FR LS PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including PVC insulated unsheathed FR LS 6.0 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engr-in-Charge.

S & F ceiling fans complete with electronic type regulator and accessories 230 Volts, 1200 mm sweep BEE 5 star rated compelte all as specified and directed.

M/s Gupta Constructions