SPECIAL REPAIR TO BUILDING NO. P-205/01 TO 04, P-206/01 TO 04, P-207/01 TO 04 AND P-202/01 TO 04 AT MILITARY STATION SRI GANGANAGAR

Amount

Taking down cement plaster of any description from brick walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 12mm thick on fair faces of brick or concrete surfaces of wall in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for 15 mm thick rendering on fair faces of brick or concrete surfaces of walls in cement mortar (1:4) finished even and smooth without using extra cement complete all as specified & directed by Engineer-in-Charge.

M&L for 5 mm thick rendering in cement mortar (1:3) on fair faces of concrete surfaces of ceilings finished even and smooth without using extra cement complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of new plastered or unplastered surface of ceiling and applying three coats of white wash complete all as specified & directed by Engineer-in-Charge.

M & L two coats of oil bound distempering over chalk whiting on new plastered surface of wall including preparation of surface complete all as specified and directed by Engineer - in - Charge.

M&L two coats of cement base paint over a coat of white washing to new plastered surface on wall including preparation complete all as specified and directed by Engineer - in - Charge.

M&L for non skid coloured joint free mat finish ceramic tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

M&L for non skid coloured joint free mat finish ceramic tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18sqm as in vertical surface such as skirting, dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 10mm thick rendering in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Dismantling brick tiles or terracing tiles single layer on roof laid dry and pointed in cement mortar all as specified and directed by Engineer-in-Charge.

Taking down shutters exceeding 1.0 Sqm and not exceeding 2.0 Sqm each complete all as specified & directed by Engineer-in- charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exceeding 4.0 Sqm each complete all as specified & directed by Engineer-in- charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm each complete all as specified & directed by Engineer-in- charge.

S & F steel section windows in out both side (one side for glazed and other for gauzed) with side hung shutters including projecting type or box type hinges , steel handles left & right and steel peg stay rods, with and including 10mm square bar grill brick cut shape in between glazed and gauged shutters complete with glazing & gauzing bars, dovetailed or welded complete all as specified and directed by Engineer - in - Charge. Note: Only Glass and wiremess will be measured and paid seperately.

S&F coloured Aluminium frame for doors, window, ventilators or grill with one or more rebates including joining cleat for fixing etc complete with powder coating on Aluminium minium thickness of powder coating 50 micron as per the specification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners . Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required all complete as per the direction of Engineer-in-charge

S&F coloured Aluminium shutters, aluminum section weighing 0.55 Kg/m including necessary joining cleats, glazing, clips, rubber neoprene packing, handles 2 nos in each door, hinges, anodised aluminium snap beading screw with powder coating of any colour (thickness of powder coating not less than 50micron) etc complete all as specified and directed by Engineer-in-Charge. Note: Only Glass will be measured and paid seperately.

S&F Aluminum Grill of 5mm dia and 50mm aparture powder coated fixed with and including 20mm wide & 2mm thick aluminium flat fixed with screw complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tack or stainless steel wire staples complete all as specified & directed by Engineer-in- charge

S&F sheet glass 3mm thick ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each pane complete all as specified & directed by Engineer-in-charge .

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tack or stainless steel wire staples complete all as specified & directed by Engineer-in- charge

S&F in repairs sheet glass 3mm thick ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each pane complete all as specified & directed by Engineer-in-charge .

S & F in repairs aluminium handles cast type anodised, 125mm long complete all as specified and directed by Engineer - in - Charge.

S&F in repairs 150 mm long Aluminium anodised barrel tower bolt of extruded section complete all as specified and directed by Engineer-in-charge.

S & F in repairs aluminium alloy, anodized, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminium alloy and fixed complete all as specified and directed by Engineer - in - Charge.

S&F in repairs 150 mm mild steel barrel tower bolts, stove enamelled black with bright bolt & fixed complete all as specified and directed by Engineer-in-Charge

S&F in repairs 150mm mild steel pressed handles oval type stove enamelled black complete all as specified and directed by Engineer-in-Charge

S&F in repairs 300 mm mild steel sliding door bolts, clip type, stone enameled block with bright bolt not less than 12mm dia with and incl a minimum of 6 bolts and nuts, 4 on bolt plate 2 on staple plate complete all as specified and directed by Engineer-in-Charge

S&F in repair 300 mm long ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-charge.

S & F pressed steel door frames with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., size of frame 105x60mm complete all as specified and directed by Engineer - in - Charge.

S & F pressed steel door frames with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., size of frame 125 x 60mm complete all as specified and directed by Engineer - in - Charge.

S&F plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints in 2nd class hard wood complete all as specified and directed by Engineer - in - Charge.

M&L for Plain fillets or beading of sectional area Exc 3 & n. exc 6 sq.cm of 2nd class hard wood square, rectangular or triangular in section , clean sawn, se-cured with nails or brads for securing wiremesh or similar works put together with glue pinned at joints in complete all as specified and directed by Engineer - in - Charge.

M&L Cement concrete 1:3:6 type C–0 (12.5 mm graded stone aggregate) filling of pressed steel frame and hold fast blocks etc complete all as specified and directed by Engineer - in - Charge.

M&L 25 mm thick block board grade 2 quality interior grade decorative face veneers on both face fixed with screw to frame work as in kitchen cabinet , almirah shutter, slab etc complete all as specified and directed by Engineer-in-Charge

S&F continous piano hinges mild steel bright finish or galvanised of 30mm width complete all as specified and directed by Engineer-in-Charge

S&F 35 mm thick gauged skelton shutters open rebeted and prepared to receive gauze etc edges of framing plain , chamferedv or rounded fitted with cut and mitred beady for receving gauze etc of 35 mm thick and door for IInd class hard wood rail and style and complete all as specified and directed by Engineer-in-Charge

S&F 35 mm thick Factory made IInd class hard wood plain framed panelled shutters (Two Panels ) with lock rails and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces . the size of rail and stile as per IS :1003 (Part -i) Kiln Seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge

M&L two coat of synthetic enamel on wooden surfaces (ordinary tint) over new surface over 10cm width or girth including preparation of surface complete all as specified and directed by Engineer - in - Charge.

S & F of Fiber Glass Reinforced plastic (FRP) Door Frames of three legged of cross section 90mmx45mm having single rebate of 32mmx45mm having single rebate of 32mmx15mm to receive shutter of 30 mm thickness. The laminate door frame molded with fire retardant grade unsaturate polysterresinn and chopped mat.Doorframe laminate shall be 2 mm thick and shall be filled with suitable wooden black in all the three legs. The frame shall be covered with fiberglass from all sides MS stay shall be provided at the bottom to steady the frame.complete all as specified and directed by Engineer - in - Charge.

S & F of 30mm thick glass fiber reinforced plastic (FRP) paneled door shutter of required color and approved brand and manufacture made with fire retardent grade unsaturated polyster resin moulded to 3mm thick FRP laminated for forming hollow rails and style with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings cast monolithically with 5mm thick FRP laminate for panels for conforming to IS:14856-2000 complete all as specified and directed by Engineer - in - Charge.

S&F mild steel butt hinges “medium weight” 100mm long cold rolled mild steel complete all as specified and directed by Engineer - in - Charge.

S & F in repairs, hasp and staple, safety type of aluminium anodised100mm size fixed with screw complete all as specified and directed by Engineer - in - Charge.

S & F aluminium handles cast type anodised, 125mm long complete all as specified and directed by Engineer - in - Charge.

S&F 150 mm long Aluminium anodised barrel tower bolt of extruded section complete all as specified and directed by Engineer-in-charge.

Demolition of mud puska in roofs, full thickness including plastering and leeping, removing rubbish off the premises cleaning surface by water and preparing to receive new plaster or other treatment complete all as specified and directed by Engineer-in-Charge.

M&L for Roof treatment to RCC roof as follows :- (a) Cleaning the roof surfaces thoroughly using wire brushes to remove sharp projections, cleaning joints,washing,drying and removing all dirt/dust to receive concrete padding/ plaster etc complete. (b) Providing 15 mm thick screed bed or bedding layer of cement mortar (1:4) with WPC , finished even and smooth without using extra cement. (c) Providing one coat of approved bituminous primer @ 100 gms per sqm, over dried plastered surface. (d) Laying 3 mm thick APP based polymeric membrane,(mineral finish) minimum weighing 3 Kg/Sqm reinforced with non woven polyster fabric (weight not less than 150 gms/Sqm) by torch application. The overlapping while torching shall be 75 mm on longitudinal direction and 100 mm on the transverse direction complete all as specified and directed by Engineer-in-Charge. Makes:-STP, Dr Fixit / Pidilite, Texsa India Ltd Notes:(i) All joints and change in directions should be covered with cement mortar (1:3) mixed with SBR latex @ 200 ml/bag of cement/ as per site requirement and cured well before laying membrane by torching. (ii) All angles and abuttments should be sealed well with extra care to ensure full bondage. (iii) Water proofing treatment shall be got carried out by approved authorised applicator of manufacturer only.The name of firm shall be got approved from GE before carrying out the work. (iv) The independent testing of membrane for technical parameters given in particular specifications shall be carried out from Govt approved labs having fascilities for testing of membrane. (v) The guarantee of treatment shall be for minimum 10 years reckoned from date of completion of whole work

M&L for heat resistant aluminium painting on roof water proofed surface complete all as specified and directed by Engineer - in - Charge.

S&F PVC bathroom cabinet with mirror of size 450x350mm complete all as specified & directed by Engineer-in-Charge. Make : Prayag Cat Part No. 551/polytuf /Shakti/Pearl as approved by GE

M&L glazed ceramic coloured tiles interior grade, of size 300x200x7mm etc as on vertical surfaces like dados or skirting over and including 10mm thick rendering in CM 1:4, set & jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles etc complete all as specified and directed by Engineer - in - Charge.

Taking up or down for 20mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

Taking up or down for 15 mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

S&F steel water tubing galvanised 15mm bore, “medium grade” with all fittings and fixed to walls and ceiling or in floor complete all as specified and directed by Engineer - in - Charge.

All as per item No 53 above but fixing with new fittings only (Old serviceable pipe will be used obtained from item No 52) complete all as specified and directed by Engineer - in - Charge.

S&F steel water tubing galvanised 20mm bore, “medium grade” with all fittings fixed to wall and ceiling or in floor complete all as specified and directed by Engineer - in - Charge.

All as per item No 55 above but fixing with new fittings only (old servicable pipe will be used obtained from item no 51) complete all as specified and directed by Engineer - in - Charge.

S&F in repairs bib taps fancy type chromium plated screwed for iron pipe or brass ferrule for 15mm bore complete etc of make pearl , jaguar etc all as specified and directed by Engineer - in - Charge.

S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers, wastes jali and a plain waste pipe of 600mm length including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specified and directed by Engineer-in-Charge

S&F in repairs, stop valves, CP Fancy type, high pressure copper alloy, with crutch or butterfly handles, screwed both ends for 15mm bore iron pipe or brass ferrule complete all as specified and directed by Engineer - in - Charge.

S&F in repairs Gun-metal , globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed for 20mm bore iron pipe or brass ferrule complete all as specified and directed by Engineer - in - Charge.

S&F in repairs cromium plated shower rose of size 125mm with or without shivel joints as specified including fixing to pipe or union complete all as specified and directed by Engineer - in - Charge.

S&F in repairs white colour rotational moulded polyethylene water storage tank 500 ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engineer - in - Charge. Note : PVC tanks shall be ISI marked and having three layers

S&F in repairs, 20mm bore ball brass valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed by Engineer - in - Charge.

Dismantling cast iron work of any description and any position complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed by Engineer - in - Charge.

S&F 75mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron bends sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

S&F 75mm bore cast iron bends sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

M&L salt glazed store ware gully traps 125x100mm square or round mounted type "P" complete all as specified and directed by Engineer-in-Charge

M&L for CI floor trap 75 mm with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer-in-Charge

M&L for CI floor trap 100 mm with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer-in-Charge

M&L bands straps supports or stays for rainwater ventilating pipes or similar work including bolts confirming to Fe 410 -0 or Fe 310-0 complete all as specified and directed by Engineer-in-Charge

S & F in repairs Stack clamps out of 50mm by 5 mm flat iron for 100mm bore pipe and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof etc complete all as specified and directed by Engineer - in - Charge.

S&F in repairs 110mm bore PVC (SWR) rain water pipe single socketed in any length with rubber ring joints, jointed with solvent joint fixed to wall complete all as specified and directed by Engineer - in - Charge.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed by Engineer - in - Charge.

Dismantling of brick work built in cement mortar of any description complete all as specified and directed by Engineer - in - Charge.

M&L Fly Ash brick work straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 complete all as specified and directed by Engineer - in - Charge.

M & L Fly Ash brick work straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed by Engineer - in - Charge.

M&L 10mm thick rendering in CM 1:6 to fair faces of brick / concrete wall surfaces finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer - in - Charge.

S&F in repair stainless steel plate rack of size 900mm x775mm x 250 made out of 1mm thick stainless steel of first quality complete all as specified and directed by Engineer-in-Charge. Make: Anupam International Model No KPR-315 or equivalent make and model approved by GE.

S&F in repairs, PVC low level flushing cistern 10 lirs capacity, valve-less, syphonic action type, white, with inlet, ball valve, float, and handle including brackets, including 32mm bore flush pipe of polyethylene of low or high density of PVC complete all as specified and directed by Engineer - in - Charge.

S&F in repair fancy type curtain rod 25 mm dia with brackets and knob etc complete all as specified and directed by Engineer-in-Charge

Demolition of RCC slabs, chajjas and similar items complete all as specified and directed by Engineer - in - Charge.

M & L RCC 1:1½:3, Type A–1 for slabs supported on walls, beams, columns and in shelves or similar items the like complete all as specified and directed by Engineer - in - Charge.

Form work to soffits of suspended slabs such as roof slab, chajja, lintel beam and similar work not exceeding 200mm thick with rough finished surface of concrete complete all as specified and directed by Engineer - in - Charge.

M & L mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No.88 above but in stirrups, spacers and binder etc complete all as specified and directed by Engineer - in - Charge.

Taking down old unserviceable glass panes of windows , cleaning properly , keeping in safe custody for refixing and glazing with & including oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and directed by Engineer - in - Charge.

Demolation of cement concrete in sunken portion and floor including removing the debrises complete all as specified and directed by Engineer-in-Charge

M&L for water proofing treatment to RCC sunken slab as specified below asd as directed by engr-in-charge:- (a) 15mm plaster in CM 1:3 with WPC on raised vertical surface. (B) Cleaning the surface with wire brush/coir brush, removing loose material like dust particles ,dirt etc. (c) Creating fillet covering of 50x50 mm with polymer modified mortar on the junction of slab and walls (d) Apply first coat of two component modified polymer coating on the horizontal and vertical surfaces. (e) Provision of glass fibre mesh of 2x2 mm immidiately on above coating (f) Apply second coat of two component modified polymer coating after 72 hours (g) Laying concrete 1:4:8 over the coating as per requirement (h) Joining the sanitary pipe with non shrink cementatiuos grout (k) Complete the treatment to be carried out by authorised applicator of water proofing manufacturer Make :- Dr.Fixit/ Fosroc/ BASF/ STP NOTE : (i) The Treatment shall be carried out as per the manufacturers industreis and as directed by Eng-in-charge. (ii) The plan area of floor shall be consider for payment.

M&L cement concrete 1:5:10 Type E-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed by Engineer-in-Charge

M&L for welding in repairs Thickness of metal to be welded will be Exc 9 mm but not exc 20mm complete all as specified and directed by Engineer - in - Charge.

S & F framed work such as grills, gratings, cooler stands etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming to Fe 290 – Gde – 165 complete all as specified and directed by Engineer - in - Charge.

M&L for 3mm thick wall care putty on wall in patches making square or rectangular shape including smooth finishing to receive finishes etc complete all as specified and directed by Engineer - in - Charge.

M&L for 3mm thick wall care putty on ceiling in patches making sqare or rectangular shape including smooth finishing to receive finishes etc complete all as specified and directed by Engineer - in - Charge.

M&L two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide on steel surface over 10 cm width or girth, not otherwise described including preparation of new steel surface complete all as specified and directed by Engineer - in - Charge.

M&L two coats of cement base paint over old decorated plastered surface on walls, after complete removal of existing treatment including necessary preparation complete all as specified and directed by Engineer - in - Charge.

M & L for complete removal of existing treatment of wall surfaces ,applying 3mm thick wall care putty making surface even and smooth and then applying two coats of oil bound distemper all as specified and directed by Engineer - in - Charge.

M & L for two coats of white wash to old decorated plastered surfaces of ceilling including preparation of surfaces complete all as specified and directed by Engineer - in - Charge.

M&L one coat of synthetic enamel on wooden surfaces (ordinary tint) old painted surface over 10cm width or girth including preparation of surface complete all as specified and directed by Engineer - in - Charge.

M&L one coats of synthetic enamel paint (ordinary tint) on steel surface over 10 cm width or girth, not otherwise described including preparation of old steel surface complete all as specified and directed by Engineer - in - Charge.

M&L machine cut Kota stone slab flooring 15-20mm thick over and inclueding 10 mm thick screed base in cement 1:4, laid and jointed with grey cement slurry mixed with pigments to match the shade of the slabs including neccesary five cutting / rubbing in kota stone to achieve the mirror finish polishing complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 104 above but on vertical surfaces over and including 10mm thick rendering in CM 1:3 finished even and fair, complete all as specified and directed by Engineer - in - Charge.

M&L 15 mm thick Green marble machine cut in skirting/dado, sehlves etc laid over and including 10 mm thick cement mortar 1:3 screed set and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing polishing complete all as specified and directed by Engineer-in-Charge

S&F in repair water closet vitreous china squatting pan "Orrisa pattern" size 580mmx440mm white with integral foot rests (Excl flushing cistern) complete all as specified including CI 'P' trap complete all as specified and directed by Engineer-in-Charge

Resecuring or easing & adjusting of door windows of any description without taking down from frame including materials if any required of size exc 1 sqm but not exc 2 sqm complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

S&F 75mm bore cast iron Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

M & L for 50 mm thick cement concrete type C – 1 (1:3:6) using 20mm graded stone aggregate as in plinth protection or similar works finished even and smooth etc complete all as specified and directed by Engineer - in - Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding and rubbish off the premises complete all as specified and directed by Engineer - in - Charge.

S&F in repairs vitreous china wash hand basin of size 450x300mm including brackets , 32mm CP waste coupling , 32mm bore Bottle trap of PTMT having minimum water seal of 25mm (Minimum weight 32mm-260gms) , 15mm bore pillar tap, 450mm long PVC Connection, cutting for and pinning in end of brackets or erecting stand etc complete all as specified and directed by Engineer-in-Charge

Demolition of PCC of any description complete and removing from premises complete all as specified and directed by Engineer-in-Charge

Demolition of precast concrete articles, kerbs stone, blocks or brick works of any description etc. laid and pointed in cement mortar complete all as specified and directed by Engineer-in-Charge

M & L providing precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in Kerb stone and setting in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge

M&L for 75mm thick PCC as in foundation / subbase type D-2 1:4:8 (40mm graded stone aggregate) complete all as specified and directed by Engineer-in-Charge

M&L for Machine pressed Precast cement concrete interlocking paver block with Grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade complete all as specified and directed by Engineer-in-Charge

M&L for sand filling under floor or in foundation including watering and well consolidation complete all as specified and directed by Engineer-in-Charge

Shotcreting 50MM thick in RCC columns, beams and slabs etc in layers with approved design mix (minimum cement content of 350 Kg/Cum on M-25) concrete having the specified minimum characterristic compressive strength (with ordinary portland cement, coarse sand and graded stone aggregate of 10 mm maximum size in proportion as per design criteria) including the cost of certering and shuttering at edges and corners etc as directed by Engineer-in-Charge including Chipping of unsound /weak concrete material 50mm average thickness from slabs,beams, columns etc with manual chisel and /or by standred power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and thoroughly washing with water and allowing it to dry etc. including removal of rust by applying approved rust removal chemical & the coating with Dr Fixit epoxy zinc primer@ 6sqm/ltr at DFT of 100microns as per specifications and disposal of debries for all lead and lifts complete all as specified and directed by Engineer-in-Charge

Providing, mixing and applying SBR polymer (of approved made) modified cement mortar 25mm thick in two layers including chipping, cleaning and priming to iron surfaces in proportion of 1:4 (1 cement and 4 graded coarse sand with polymer minimum 2% by weight of cement used) complete all as specified and directed by Engineer-in-Charge

Providing and injecting appoved grout in proportion Stirrer mixed Acrylic Polymer of approved make @ 2% of weight of cement used ) modified cement slurry non shrinx compound in concrete /RCC work. made with recommended by the manufacturer into cracks/honey-comb area of concrete/masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete all as specified and directed by Engineer-in-Charge. Note:- The payment shall be made on the basis of actual weight of approved grout injected

Providing and fixing hard drawn steel wire fabric of size 25mm x 25mm mesh or other suitable size wire mesh to be fixed and firmly anchored to the concrete surfaces by means of "L" shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tools and plants complete all as specified and directed by Engineer-in-Charge.

Supply only liquid water proofing compound complete all as specified and as directed by the Engineer-in-Charge. Make : Dr Fixit / Fosroc / BASF / STP

M & L 15mm thick waterproof plaster using cement sand mortar 1:3 on slab/existing roof surfaces & vertical surface admixed with Dr Fixit Pidiproof LW+ @ 200ml per bag of cement complete all as specified and directed by Engineer-in-Charge.

M & L for 25mm thick plain cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate on roof slab complete all as specified and directed by Engineer-in-Charge.

Providing and applying microfiber reinforced UV resistant Acrylic polymer coating three coats having solid contents 69% polymer content 35% & Tensile strength 2.6N/mm2 of Dr. fixit Newcoat/stat/parex or equivalent with a paint brush over existing roof surface after removal of all loose material, lime dust etc. with wire brushes, coir brushes from roof surface to get absolutely cleaned surface free of foreign contaimnant filling of cracks wherever found with polymer based mortar, and after repairing the surface apply primer coat with Dr. fixit Primeseal. polyester reinforced fiber net laid on the surface after the first coat and all the joints of brick is repaired by polymer based mortar. Undulation on the surface repair before executing the water proofing treatment complete all as specified & directed by Engineer-in-charge. Note : The treatment shall be carried out by authorised applicator approved by GE as per the manufacturer instructions & as directed by Engineer-in-Charge.

M&L for Endura cool roof tiles 300x300x10mm white vitrified water absorption <0.5% SRI > 90 (ASTME1980, EN673 and EN 411) BEPL (Building energy performance laboratory) certified laid over screed bed or bedding layer of mortar 15mm thick CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Providing and applying rising damp proof coating system with single component ready to use damp proof coating Roff Hydamp complete all as specified and directed by Engineer-in-Charge :- (A) SURFACE PREPARATION : Thoroughly brush and clean all laitance, loose particles, efflorescence, bird droppings etc. all large voids or hollow portion must be removed. Non moving cracks having width upto 5mm most be filled with polymer based crack filler. (B) APPLICATION : Apply the first coat of Roff Hydamp with a paint brush directly on the prepared surfaces. Allow to dry for a minimum 2-3 hours. Apply one part of Roff Hydamp and 2 part of OPC white cement and make the putty. Apply putty on the entire surfaces area. Allow to dry for atleast 3-4 hours. Apply the final coat of Roff Hydamp on the entire surfaces complete all as specified and directed by Engineer-in-charge.

S&F in repairs 50mm bore High density polyethylene (HDPE) pipes of pressure rating 6 kgf/sq. cm including bends if required jointed with solvent joint fixed to wall or in floor complete all as specified and directed by Engineer - in - Charge.

S&F in repairs grating doom 100 mm dia of PTMT (minium weight 25 grams) complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description exc 1 Sqm but not exc 2 sqm each complete all as specified and directed by Engineer-in-Charge

M&L for Mild steel work as ISMB , Joist, channel, angle, or tee sections fixed and embedding brick work including cutting welding and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates including necessary welding, rivetting etc. confirming to Fe 410 -W (GdeE- 250) quality A etc complete all as specified and directed by Engineer-in-Charge

Taking down carefully copper/aluminium point wiring (light, fan, socket, bell or power) complete including fittings such as switches, ceiling roses, pendent holders, light fittings any type, sockets, regulators etc and making good disturbed surfaces of walls and floors etc to match with the existing surfaces complete all as specified and directed by Engr-in-Ch.

M&L for point wiring complete with 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable drawn in and including concealed PVC rigid conduit pipe medium grade 20mm dia using pipe hooks, elbows, junction covers and junction boxes including provision of 1.2mm thick pressed steel sunken terminal boxes 60mm deep, suitable length and painted with red oxide primer for mounting switches, sockets, fan regulators covered with and including 3mm thick bakelite plastic laminated sheet top cover fixed flush with wall using brass screws & cup washers including 1.5 Sqmm PVC insulated solid copper conductor wire as earth continuity to common earth and connecting to earth dolly for one light point controlled by one switch, bell push or one fan point controlled by one switch and making the good of disturb surface of wall in CM 1:3 with white wash or existing colour complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 135 here in before, but for one 3 pin socket combination 5/6 Amps on indipendent board complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 135 here in before, but for one 3 pin socket outlet 5 Amps on same board complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 135 above, but with multi-stranded copper conductor FRLS PVC sheathed cable of cross sectional area 2.5 Sqmm including 2.5 Sqmm PVC insulated solid copper conductor wire as earth continuity to common earth dolly for 5 Pin 15 Amp socket combination outlet on independant board complete all as specified & directed by Engineer-in-Charge.

All as per Srl item No 135 here in before, but for one light point controlled by two 2 way swiches complete all as specified & directed by Engineer-in- charge.

M&L for point wiring complete with 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable drawn in and existing concealed PVC regid conduit using new sunken boxes of cast iron / pressed steel terminal boxes suitable length and thickness for mounting switches, sockets, fan regulator with 3mm thick plastic laminated sheet cover fixed with brass screws and cup washers, duly grouted and painted with red oxide metal primer and including provision of continous earth continuity conductor alongwith point wiring of 1.5 Sqmm copper PVC insulated cable for one light / fan point controlled by one switch and connected to common earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 140 here in before, but for one 3 pin socket combination 5/6 Amps on indipendent board complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 140 here in before, but for one 3 pin socket outlet 5 Amps on same board complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 140 above, but with multi-stranded copper conductor FRLS PVC sheathed cable of cross sectional area 2.5 Sqmm including 2.5 Sqmm PVC insulated solid copper conductor wire as earth continuity to common earth dolly for 5 Pin 15 Amp socket combination outlet on independant board complete all as specified & directed by Engineer-in-Charge.

S&F switch piano flush type single pole one way 5/6 Amps, 230 volts complete all as specified & directed by Engineer-in- charge.

S&F switch piano flush type single pole two ways 5/6 Amps, 230 volts complete all as specified & directed by Engineer-in- charge.

S&F bell push flush type 5 Amps complete all as specified and directed by Engineer-in-Charge

S&F switch socket combination 5 Pin, 5/6 Amps flush type complete all as specified and directed by Engineer-in-Charge.

S&F switch socket combination 6 Pin, 5/15 Amps flush type complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet 5 ;Pin, 5 Amps flush type complete all as specified and directed by Engineer-in-Charge.

S&F ceiling rose polycarbonate surface bakelite 65 x 50mm size three terminals complete all as specified and directed by Engineer-in-Charge.

S&F electronic bell ding dong type, AC 230 Volt single pole complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of existing light fittings with batton integrated LED channel 22 Watt (integral sleek extruded polycarbonate body LED with white acrylic cover) tube light fittings wall mounted complete with rod driver and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2mm upto ceiling rose / connector complete all as specified and directed by Engineer-in-Charge.

S&F Angle holder insulated body with back plate for conduit fittings including LED lamp 9 W complete all as specified and directed by Engineer-in-Charge.

Supply and fixing stepped electronic regulator 400 watt (flush type) for ceiling fan on the existing phenolic laminated sheet etc as required complete all as specified by Engineer-in-charge.

S&F water tight bulk head fittings, comprision of connector galvanized cast iron back plate, wheather proof enamelled gallery, glass well and including 10 Watt LED lamp complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of sub-main wiring with two runs of single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLS stranded copper conductor drawn into and including PVC concealed conduit, including one run of 6 Sqmm (Nominal Area) copper cable as earth continuity conductor including necessary connections, PVC flexible pipes are used in panel board while connecting the cable complete all as specified and directed by Engineer-in-Charge. Note : Two runs of 6 Sqmm single core cable and one run of 6 sqmm copper wire earth continuty conductor and conduit with fittings shall be measured as one length.

S&F in repairs factory made sheet metal enclosure for double door distribution board made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 way, 240 Volts, ISI Marked, 200 Amps bus bar stove enameled dust and vermin proof suitable for incorporation of MCBs and Isolators etc. complete all as specified & directed by Engineer-in-Charge.

S&F factory made sheet metal enclosure for double door vertical distribution board made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy power coated surface mounting VTPN 4 Ways 415 Volts ISI Marked, 125 Amps bus bar stove enameled dust and vermin proof, IP-43 protection suitable for incorporation of FP MCCB (V-Tech) N1 Frame upto 125 Amps, Isolators and including to give connection with wire and cable etc. complete all as specified & directed by Engineer-in-Charge.

S&F MCCB TPN 63 Amps with breaking capacity of 25 KA, fixed TM and 415 volts, AC supply, ISI marked complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, MCB 'B' series type suitable for 240 volts, AC supply, 5 to 40 Amps, single pole with over load and short circuit protection and rupturing capacity not less than 10 KA complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, MCB 'B' series type suitable for 240 volts, AC supply, 5 to 40 Amps, SP & N with over load and short circuit protection and rupturing capacity not less than 10 KA complete all as specified and directed by Engineer-in-Charge.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick packed layer of charcoal dust and common salt, connected to galvanized iron strip 32mm x 6mm thick as earth lead by means of bolts, nuts and washers of galvanised iron or steel and thimbles and other end of the earth strip connected to earthing test point/equipment and protected by galvanised iron pipe light grade 40mm dia upto earthing test point/equipment fixed with 2 Nos of mild steel clamp made out 25mm x 3mm flat iron and perforated water pipe 20mm dia GI medium grade and top with socket & plug and bottom connected to earth plate by slit and two bolts/nuts/washers, PCC chamber in cement concrete (1:2:4) type B-1 and CI cover with frame 40 x 40 x 6mm on top and excavation/ earth work complete all as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2009. Note:- (i) Outer edge of earth pit shall be 1 metre away from the outer edge of PCC chamber. (ii) GI strip upto earth test point/equipment is included in this item. (iii) Water pipe upto earth pit shall be provided in slantling position as included in this item.

S&F security light fittings LED type 25 Watt with all necessary accessories, clear transparent acrylic cover, prewire suitable to operated on 230 Volts, 50 Hz, AC and supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 32mm bore "light grade" brackets 2 Mtr length bent to shape to obtain required shape including clamps, nuts, bolts, washers etc. connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer-in-Charge.

Supplying and laying GI pipes light grade 50mm dia for cable crossing in floors and fixing with existing light pole including nuts, bolts, clamps etc. complete all as specified and directed by Engineer-in-Charge.

Fixing only Exhaust Fan and connecting up including provision of cable from ceiling rose / connector to fan complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches, not exc 1.5 m wide and n. exc 1.5 m depth; or n exc 10 Sqm on plan and n exc 1.5 m in depth for foundations of poles, struts, stays etc. or laying underground cable etc. in soft/loose soil, & getting out complete all as specified and directed by Engineer-in-Charge.

Returning, filling in soft/loose soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in soft/loose soil complete all as specified & directed by Engineer-in-charge.

Removal of excavated surplus soil to a distance n.exc 250m and depositing where directed at level not exceeding 1.5 m above the starting point complete all as specified & directed by Engineer-in-charge .

M & L for sand cushioning with river washed and screened dry fine sand to under ground cable after laying the cable jently punning down complete all as specified and directed by Engineer-in-Charge. NOTE:- Thickness after punning shall be considered for payment.

M & L for brick protection with old size sub class 'B' bricks laid flat , length of bricks across the route of underground cable complete all as specified and directed by Engineer-in-Charge.

Supplying, laying, jointing and testing and commissioning of 16 sqmm, 4 core XLPE insulated, screened, PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 volts grade conforming to IS-7098 laid in trenches/ ducts/ fixed on poles/wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by Engineer-in-Charge. Note :Excavation, earth work, sand cushioning and brick protection required for item shall be measured and paid separately under respective items of BOQ. ______________________________________________________________________ Note : A sum of Rs. 95,454.00 will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 41, 42 & 43(R) (Schedule of Credit) of Tender documents

M/S KARNI CONSTRUCTION COMPANY

M/S BUDHRAM BISHNOI

Aggarwal brothers and company

M/s Balvinder Singh Engineer and Contractors

M/s MITTAL CONSTRUCTIONS