Upgradation of Science laboratories and library blocks at Government Degree Collage For Women Anantnag Kashmir.

Amount

PART- (A) PSYCHOLOGY LABORATORY

Dismantling of old damaged ceiling in all floors including disposal of unserviceable materials as desired complete.

Providing ist. Class budloo wood work in frames of false ceiling, partions etc. sawn and put up in position

Providing and fixing 25 mm thick ist. Class budloo wooden planks in ceilings ( frame work for base to be paid for separately)

Providing and fixing 12 mm thick flat pressed 3 layer medium density particle board or graded particle board (Grade-I) in TILE form IS;3087 marked in ceiling with necessary nails etc. complete ( frame work to be paid for separately)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade (Two or more coats on new wood work over an under coat of suitable shade with ordinary paint of approved brand and manufacture)

Providing and fixing of pre coated galvanized iron high rib or tile profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm +/- 5% total coated thickness (TCT), zinc coating 120 gms. As per IS : 277 in 240 mpa steel grade, 5-7 microns epoxy primer on bothe sides of the sheet and polyester top coat 15-18 microns , sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length up to 12 metre . The sheet shall be fixed using self drilling / self tapping screws of size (5.5 x 55 mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts washers or G.I limpet washers flled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excl. the cost of purlins, rafters and trusses and incl. cutting to size and shape wherever reqd.

Providing three seater table and bench made of ist. Class imported kail wood of required size and shape including all necessary nails, screws, polishing two or more coats of melamine polish and all carriages up to site of work complete job.

Point wiring for switch controlled primary light points with 3x1.5 sq mm (P+N+E) FRLS PVC insulated 660/1100 v grade flexible standard copper conductor wires in IS embossed 25 mm dia PVC recessed and surface conducting and including the cost of providing saddles /hangers etc. for surface conducting and including the cost of supplying and fixing plate mounted flush mounted 240 v 6 amp control switch of approved quality and color hoshed in zinc chromate passivity GI box and complete as per specification and as required .

Point wiring for 6 amp socket outlets with 3x2.5 sqm (P+N+E ) FRLS PVC insulated 660/1100 volt grade flexible standard copper conductor wires in IS embossed 25mm dia PVC recessed and surface conducting system including the cost of providing saddeles /hangers etc as required and including the cost of cutting /making good chases in brick work and including the cost of supplying and fixing modular grid plate mounted 240 v 6 amp pin combined shuttered socket outlets along with 240 v 6 amp control switch of approved quality and colour hoshed in zinc chromate passivity GI boxes with and including cost of circuit wiring from DB to 3pin socket in the sub circuit complete as per specification as required .

Point wiring for 16 amp socket outlet with 3x4 sqm ( P+N+E) FRLS PVC insulated 660/1100 volt grade flexible standard copper conductor wire in IS embossed 25mm dia PVC recessed and surface conducting system including the cost of providing saddeles /hangers etc as required and including the cost of cutting /making good chases in brick work and including the cost of supplying and fixing modular grid plate mounted 240 v 6 amp pin combined shuttered socket outlets along with 240 v 6 amp control switch of approved quality and colour hoshed in zinc chromate passivated GI boxes with and including cost of circuit wiring from DB to 3pin socket in the sub circuit complete as per specification as required .

Wiring for ceiling/wall Fan points same as above in item No 1. but controlled by electronic stepped regulator 200 watts and 5A control switch and 15mm dia circular or hexagonal in 1.6mm thick MS zinc passivity sheet steel body and 12mm dia MS bar hook complete with white ,3mm thick 200mm dia laminated circular cover.

Supplying installation testing and commissioning of celling fan of usha make 1200 mm double wall bearing .

Supplying installation testing and commissioning of wall fan of Ushamake.

Supplying installation testing and commissioning of exhaust fan of Crompton make

Supplying installation testing and commissioning of 15 watt surface mounted LED light of Syska halonex Havells or its equalent make

Supplying installation testing and commissioning of distribution boxes 24 ways

Supplying installation testing and commissioning of following MCBs and MCCBs fixed in 24 ways distribution box a) 6-32-amp single pole MCBs

b) 40-63 Amp DP MCBs

Supplying and laying of 7/16 service line of havells make

Supply and laying of 1100 v grade XLPE insulated PVC sheeted conductor armed cable as per specification in trench cable try ducts over bed stand clumped to wall with suitable clamp including MS conduit PVC and fixing bolts connecting testing and commissioning. (FOR SUB MAIN) a) 2x 6 sq. mmcopper conductor including conduit

b)2x4+1x1.5 sq. mm copper conductor including conduit.

Supply and laying of circuit wiring from DB to SB a)2x1.5+1x1.5 sq. mm for light circuit

Providing and fixing of chemical earthing using electrode of size 15 mm dia 2 mtr long connected with 30x4 mm GI RCC cover with back filling compound the voltage between neutral and earth not to be exceed 2 volts the earthing included the cost of copper wire up to panel board.

Supplying installation testing and commissioning of 1250 VA inverter with 24 v double battery 185 AH including complete as required

Supply and fixing of 2mm thick PV Conduits in following sizes include cost of junction boxes, bends, elbows, sockets, tees etc. laying in slab cutting, chases and making good or surface mounted including all fixing hardware. (FOR LIGHT CIRCUITS) a). 25mm dia.

Design fabrication assembling supply installation testing and commissioning of LT sub main panel suitable for 415 V 3 phase 50 HZ 4 wire power supply system panel shall be fabricated out of 2mm thick CPCA sheet steel in cubical formation compact mobilize in form 3d construction wall mounted and shall be dust and vermin proof 3mm thick cable gland plate shall be provided both at the top and bottom of the panel MCCB 100 Amp Havells make 01 No TPN 40 Amp Legrand make 04 No BUS bar 150 Amp 01 set CT Coil 01 Set Voltmeter Digital 01 No Ammeter Digital 01 No Indication lights 02 sets

PART- (B) ZLOGY LABORATORY

Brick work with F.P.S. bricks of class designation 75 in super structure above plinth level up to floor Five level (by manual means) in cement mortar 1:6 (1 cement: 6 coarse sand) Including all carriages up to site of work complete.

12 mm cement plaster on the rough side of single or half brick wall of mix.1 : 4 (1 cement : 4 course sand)

Reinforcement cement concrete work in walls (any thickness),a) in slabs, lintals, columns, pillars, piers, abutments, posts and struts, etc. up to floor five level excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 {1 cement: 1.5 coarse sand: 3 crushed graded stone agg. 20mm nominal size) Including all carriages up to site of work complete.

Reinforcement for R.C.C. work incl. straightening, cutting, bending, placing in position & binding all complete mild steel & medium tensile steel bars.

Centering & shuttering including strutting, propping, etc. & removal of form work for Suspended floors, lintals, beams, roofs, landings, balconies and access platform.

Providing and fixing gang saw cut mirror polished Granite of any color or shape (pre moulded and pre polished), machine cut for Kitchen platform, vanity counters, window sills, facias and similar locations of reqd. size and approved shade, color and texture laid over 20 mm thick base cement mortar 1: 4 (1ccement:4 course sand) with joints treated with white cement, mixed with maching pigment, epoxy touch ups, incl. rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels Area of slab up to 0.50 Sqm) 18 mm thick

Extra for providing edge moldings to 18 mm thick Granite Work counters, Vanities etc. Over above Items incl. machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge.

Providing and fixing 600 x 450 x 200 mm white vitreous china laboratory sink with C.I brackets, C.P brass chain with rubber plug, 40 mm C.P brass waste and 40 mm C.P brass trap with necessary C.P brass unions complete, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing M.S grills of reqd. pattern in frames of windows etc. with M.S flats, square or round bars etc. all complete. Fixed to openings / wooden frames with rawl plugs/nails/screws etc.

Providing and fixing 12 mm thick Nordic Pine Wall Paneling (T & G) fully finished and all sides planed, fungus and termite proof ( seasoned moisture content 8%bto 15% ) imported type ISO:14001 approved, fixing with head less nails, all taxes of allied material involved and inclusive of ist. Class budloo wood ground work of 2”x 1.5” size, 12 mm thick commercial ply wood base, two coats of polish complete in all respects.

Providing and fixing 15 mm bore C.P sink mixer of standard manufecture and brand.

Distempering with Ist. Quality acrylic washable distemper (ready made) Two or more coats on new work of approved manufacture and of reqd. shade / colour complete as per manufacturer’s specifications.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade (Two or more coats on new wood work over an under coat of suitable shade with ordinary paint of approved brand and manufacture)

Dismantling of old damaged ceiling in all floors including disposal of unserviceable materials as desired complete.

Providing ist. Class budloo wood work in frames of false ceiling, partions etc. sawn and put up in position

Providing and fixing 25 mm thick ist. Class budloo wooden planks in ceilings ( frame work for base to be paid for separately)

Providing and fixing 12 mm thick flat pressed 3 layer medium density particle board or graded particle board (Grade-I) in TILE form IS;3087 marked in ceiling with necessary nails etc. complete ( frame work to be paid for separately)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, paneling and dash fasteners to be paid for separately) for fixed portion, Powder coated aluminum (minimum thickness of powder coated 50 microns)

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge. With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm)

Providing & fixing of aluminum partition panel sheet of approved quality /color 5mm thick in partionetc with EPDM rubber / neoprene gasket etc as per the direction of the concerned site engineer, approved quality/ color complete job

Providing and fixing aluminum round shape handle of outer dia 100mm with SS screws etc. Complete as per direction of Engineer-in-charge. Powder coated minimum thickness 50 micron aluminum

Providing and fixing of aluminum powder coated tower bolts 150mm size incl. cost of stainless steel screws ,fixing to frame etc complete

Providing & fixing of brass 100mm mortice latch and lock with six lever without pair of handles for aluminum door incl. necessary cuttings and making good etc complete job.

Providing and fixing of collapsible steel shutter vertical channel 20x10x2mm and braced with flat iron diagonals 20x5mm size ,with top and bottom rail of t-iron 40x40x6mm ,with 40mm dia steel pulleys, complete with nuts and bolts also applying of one coat of primer and two coats of paint.

PART- (C) BOTANY LABORATORY

Brick work with F.P.S. bricks of class designation 75 in super structure above plinth level up to floor Five level (by manual means) in cement mortar 1:6 (1 cement: 6 coarse sand) Including all carriages up to site of work complete.

12 mm cement plaster on the rough side of single or half brick wall of mix.1 : 4 (1 cement : 4 course sand)

Reinforcement cement concrete work in walls (any thickness),a) in slabs, lintals, columns, pillars, piers, abutments, posts and struts, etc. up to floor five level excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 {1 cement: 1.5 coarse sand: 3 crushed graded stone agg. 20mm nominal size) Including all carriages up to site of work complete.

Reinforcement for R.C.C. work incl. straightening, cutting, bending, placing in position & binding all complete mild steel & medium tensile steel bars.

Centering & shuttering including strutting, propping, etc. & removal of form work for Suspended floors, lintals, beams, roofs, landings, balconies and access platform.

Providing and fixing gang saw cut mirror polished Granite of any color or shape (pre moulded and pre polished), machine cut for Kitchen platform, vanity counters, window sills, facias and similar locations of reqd. size and approved shade, color and texture laid over 20 mm thick base cement mortar 1: 4 (1ccement:4 course sand) with joints treated with white cement, mixed with maching pigment, epoxy touch ups, incl. rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels Area of slab up to 0.50 Sqm) 18 mm thick

Extra for providing edge moldings to 18 mm thick Granite Work counters, Vanities etc. Over above Items incl. machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge.

Providing and fixing 600 x 450 x 200 mm white vitreous china laboratory sink with C.I brackets, C.P brass chain with rubber plug, 40 mm C.P brass waste and 40 mm C.P brass trap with necessary C.P brass unions complete, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing M.S grills of reqd. pattern in frames of windows etc. with M.S flats, square or round bars etc. all complete. Fixed to openings / wooden frames with rawl plugs/nails/screws etc.

Providing and fixing 12 mm thick Nordic Pine Wall Paneling (T & G) fully finished and all sides planed, fungus and termite proof ( seasoned moisture content 8%bto 15% ) imported type ISO:14001 approved, fixing with head less nails, all taxes of allied material involved and inclusive of ist. Class budloo wood ground work of 2”x 1.5” size, 12 mm thick commercial ply wood base, two coats of polish complete in all respects.

Providing and fixing 15 mm bore C.P sink mixer of standard manufecture and brand.

Distempering with Ist. Quality acrylic washable distemper (ready made) Two or more coats on new work of approved manufacture and of reqd. shade / colour complete as per manufacturer’s specifications.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade (Two or more coats on new wood work over an under coat of suitable shade with ordinary paint of approved brand and manufacture)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, paneling and dash fasteners to be paid for separately) for fixed portion, Powder coated aluminum (minimum thickness of powder coated 50 microns)

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge. With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm)

Providing & fixing of aluminum partition panel sheet of approved quality /color 5mm thick in partionetc with EPDM rubber / neoprene gasket etc as per the direction of the concerned site engineer, approved quality/ color complete job

Providing and fixing aluminum round shape handle of outer dia 100mm with SS screws etc. Complete as per direction of Engineer-in-charge. Powder coated minimum thickness 50 micron aluminum

Providing and fixing of aluminum powder coated tower bolts 150mm size incl. cost of stainless steel screws ,fixing to frame etc complete

Providing & fixing of brass 100mm mortice latch and lock with six lever without pair of handles for aluminum door incl. necessary cuttings and making good etc complete job.

Providing and fixing of collapsible steel shutter vertical channel 20x10x2mm and braced with flat iron diagonals 20x5mm size ,with top and bottom rail of t-iron 40x40x6mm ,with 40mm dia steel pulleys, complete with nuts and bolts also applying of one coat of primer and two coats of paint.

Providing steel racks of size 6’-0” x 3’-6” x 1’-6” (movable) with steel glazed shutters for storage of different size books including all fittings and fixtures and finelly painting with two or more coats of synthetic enamel paint over one coat of steel primer all complete job.

PART- (D) LIBRARY BLOCK

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30 cms in depth, 1.5 mtr in width as well as 10 sqm on plan) incl. disposal of excavated earth is to be leveled and neatly dressed in all kinds of soil.

Providing and laying of stone soling tightly hand packed under foundation incld. all carriages up to site of work complete.

Providing ist. Class budloo wood work in frames/ground work of false ceiling, partions etc. sawn and put up in position

Providing and fixing 25 mm thick ist. Class budloo wooden planks in ceilings ( frame work for base to be paid for separately)

Providing and fixing 12 mm thick flat pressed 3 layer medium density particle board or graded particle board (Grade-I) in TILE form IS;3087 marked in ceiling with necessary nails etc. complete ( frame work to be paid for separately)

Providing and fixing of precast triple layer septic tank 7000 liters capacity including making all necessary connections and all carriages complete (earth work to be paid separately)

Providing steel racks of size 6’-0” x 3’-6” x 1’-6” (movable) with steel glazed shutters for storage of different size books including all fittings and fixtures and finely painting with two or more coats of synthetic enamel paint over one coat of steel primer all complete job.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade (Two or more coats on new wood work over an under coat of suitable shade with ordinary paint of approved brand and manufacture)

Repairs to broken glazed window shutters by way of providing missing parts/glass including necessary beadings, nails complete.

Distempering with Ist. Quality acrylic washable distemper (ready made) Two or more coats on new work of approved manufacture and of reqd. shade / colour complete as per manufacturer’s specifications.

Providing table cum bench made of 18 mm thick block board of required size and shape with commercial ply wood on both sides including all necessary nails, screws, polishing two or more coats of melamine polish and all carriages up to site of work complete job.

PART- (E) SERICULTURE BLOCK

Brick work with F.P.S. bricks of class designation 75 in super structure above plinth level up to floor Five level (by manual means) in cement mortar 1:6 (1 cement: 6 coarse sand) Including all carriages up to site of work complete.

12 mm cement plaster on the rough side of single or half brick wall of mix.1 : 4 (1 cement : 4 course sand)

Reinforcement cement concrete work in walls (any thickness),a) in slabs, lintals, columns, pillars, piers, abutments, posts and struts, etc. up to floor five level excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 {1 cement: 1.5 coarse sand: 3 crushed graded stone agg. 20mm nominal size) Including all carriages up to site of work complete.

Reinforcement for R.C.C. work incl. straightening, cutting, bending, placing in position & binding all complete mild steel & medium tensile steel bars.

Centering & shuttering including strutting, propping, etc. & removal of form work for Suspended floors, lintals, beams, roofs, landings, balconies and access platform.

Providing and fixing gang saw cut mirror polished Granite of any color or shape (pre moulded and pre polished), machine cut for Kitchen platform, vanity counters, window sills, facias and similar locations of reqd. size and approved shade, color and texture laid over 20 mm thick base cement mortar 1: 4 (1ccement:4 course sand) with joints treated with white cement, mixed with maching pigment, epoxy touch ups, incl. rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels Area of slab up to 0.50 Sqm) 18 mm thick

Extra for providing edge moldings to 18 mm thick Granite Work counters, Vanities etc. Over above Items incl. machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge.

Providing and fixing 600 x 450 x 200 mm white vitreous china laboratory sink with C.I brackets, C.P brass chain with rubber plug, 40 mm C.P brass waste and 40 mm C.P brass trap with necessary C.P brass unions complete, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing 12 mm thick Nordic Pine Wall Paneling (T & G) fully finished and all sides planed, fungus and termite proof ( seasoned moisture content 8%bto 15% ) imported type ISO:14001 approved, fixing with head less nails, all taxes of allied material involved and inclusive of ist. Class budloo wood ground work of 2”x 1.5” size, 12 mm thick commercial ply wood base, two coats of polish complete in all respects.

Providing steel racks of size 6’-0” x 3’-6” x 1’-6” (movable) with steel glazed shutters for storage of different size books including all fittings and fixtures and finelly painting with two or more coats of synthetic enamel paint over one coat of steel primer all complete job.

Distempering with Ist. Quality acrylic washable distemper (ready made) Two or more coats on new work of approved manufacture and of reqd. shade / colour complete as per manufacturer’s specifications.

Providing steel racks of size 6’-0” x 3’-6” x 1’-6” (movable) with steel glazed shutters for storage of different size books including all fittings and fixtures and finelly painting with two or more coats of synthetic enamel paint over one coat of steel primer all complete job.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade (Two or more coats on new wood work over an under coat of suitable shade with ordinary paint of approved brand and manufacture)

M/S BEIGH CONSTRUCTIONS

MUZAFAR AHMAD RESHI

M/S MOHD SHAFI ITOO

AABID ALI MANTOO

M/S MUSHTAQ AHMAD DAR

MANZOOR AHMAD DAR