REPAIR MAINTENACE OF PUMPS SET SUBMERSIBLE PUMP WATER SUPPLY LINES VALVES GEN SET VOLTAGE STABILIZER EXTERNAL ELECT AC WATER COOLER WITH OTHER ELECTRICAL APPLIANCE AND TESTING OF WATER IN SILA GRN KALAL KALAKOTE UNDER GE NAGROTA

Amount

Schedule A Part -I Excavating in trenches n exe 1.5 m wide and not exceeding 1.5 m in depth getting out hard/dense soil complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers n exc 25 cm in hard dense soil complete all as specified and directed.

Removing excavated soil to a distance not exc 50 m and depositing where directed at level not exc 1.5 m above the starting point complete all as specified and directed.

Taking out existing unserviceable/ serviceable Galvanised Iron pipe of 15 mm bore from the trenches including disconnecting branch connections, fittings and control valves complete all as specified and directed. (Excavation and earth work shall be measured and paid for separately)

All as per ser item No 4 above but 20 mm bore.

All as per ser item No 4 above but 25 mm bore.

All as per ser item No 4 above but 40 mm bore.

All as per ser item No 4 above but 50 mm bore.

All as per ser item No 4 above but 80 mm bore.

All as per ser item No 4 above but 100 mm bore.

Supply and laying Galvanised iron pipe 15 mm bore ISI mark with all fittings such as elbow, bends, sockets, nipples and uniun etc and fixed complete laid in trech including taking down all as specified and directed by Engr-in-charge.

All as per ser item No 11 above but 20 mm bore.

All as per ser item No 11 above but 25 mm bore.

All as per ser item No 11 above but 40 mm bore.

All as per ser item No 11 above but 50 mm bore.

All as per ser item No 11 above but 80 mm bore.

All as per ser item No 11 above but 100 mm bore.

M & L for repair/ rectification of leakage to water supply distribution lines 15 mm bore to 25 mm bore GI tubing by necessary excavation, returining, filling as required, tightening of loose joints of union, elbow, socket etc, threading if required including replacement of GI union/socket/nipple as required al as specified and directted.

All as per ser No. 18 above but for GI tubing of 40 mm bore to 50 mm bore.

All as per ser No. 18 above but for GI tubing of 80 mm bore to 100 mm bore. Note : - (i) The complaints for the above works shall be registered by contractor at the complaint cell of AGE Reasi. (ii) Stationary required such as complaint book Each Job proper record shall be maintained by the contractor. (iii) Tools and transport with driver for attending of above complaints shall be arranged by contractor. (iv) The rate quoted by the contractor for above Each Jobs under item No 18 to 20 shall be issued and measured separately under relevant item. (v) The above complaintes shall be completed within 12 Hrs of the registration of the complaints. (vi) The stores required for the works under item No 18 to 20 shall be issued and measured separately under relevant item. (vii) Excavation, returning/ filling shall be measured and paid separtely. (viii) Amount of 300 per complain will be panalised if complain is not attended with in 24 Hours.

Supply only GI fittings, medium grade, ISI marke of following sizes :-

Union 15 MM bore

Union 20 mm bore

union 25 mm bore

union 40 mm bore

union 50 mm bore

socket 15 mm bore

socket 20 mm bore

socket 25 mm bore

socket 40 mm bore

socket 50 mm bore

Reducing socket 15 mm X 20 mm bore

Reducing socket 20 mm X 25 mm bore

Reducing socket 40 mm X 50 mm bore

Elbow 15 mm bore

Elbow 20 mm bore

Elbow 25 mm bore

Elbow 40 mm bore

Elbow 50 mm bore

Reducing Elbow 15mmx20mm

Reducing Elbow 20mmx25mm

Reducing Elbow 40mmx50mm

Nipple 15 mm bore 2 inch long

Nipple 15 mm bore 4 inch long

Nipple 15 mm bore 6 inch long

Nipple 20 mm bore 2 inch long

Nipple 20 mm bore 4 inch long

Nipple 20 mm bore 6 inch long

Nipple 25 mm bore 2 inch long

Nipple 25 mm bore 4 inch long

Nipple 25 mm bore 6 inch long

plug 15mm

plug 20mm

plug 25mm

plug 40mm

Tee 15 mm

Tee 20 mm

Tee 25 mm

Tee 40 mm

Gland Paking 8 mm

Gland Paking 10 mm

Gland Paking 12 mm Note : - Rate of fixing for item No. 21.01 to 21.41 shall deemed to be included in item No. 18 to 20 above.

S & F in repair / Replacement Gun metal, globe or gate valves , with iron wheel head, screwed both ends for iron pipe and fixied of following sizes :-

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

M & L for servicing of sluice valves cast iron body by greasing / oiling using T&P as required as per manufacturer's instructions & providing gland rope of superior quality to stop any leakage of sluice valves of size 80 mm to 100 mm bore including replacement of defective brass check nuts complete all as specified and directed.

Supply and fix Foot valve for 100 mm bore including GI flanged Bolts/Nuts/washers gasket etc all and removal of old valve and ficed complete all as speified and directed.

Supply and fix Air Release valve for 100mm vore including GI flanged Bolts/Nuts/washers gasket etc all and removal of old valve and fixed complete all as specified and directed.

Supply and fix Non Return valve for 100mm vore including GI flanged Bolts/Nuts/washers gasket etc all and removal of old valve and fixed complete all as specified and directed.

Material and labour for heavy duty sluice valve 100 mm bore complete with iron wheel conforming to IS 1538, PN 1.6 of double flanged and drilled end provided with high tensile steel spindle including GI flanged Bolts/Nuts/washers gasket etc fixed in repair complete all as specified and directed.

All as per ser item No 27 above but 80 mm bore.

Material and labour for heavy duty butterfly valve 100 mm bore complete with iron wheel conforming to IS 1969, PN 1.6 of double flanged and drilled end provided with high tensile steel spindle including GI flanged Bolts/Nuts/washers gasket etc complete all as specified and directed.

All as per ser item No 29 above but 80 mm bore.

Material and labour for Repair to foot valve 100 mm bore in position by replacement of UNSV parts such as Brass ring packing/Rubber, nuts, bolts, washers rubber insertion sheet complete all as required to make it functional complete all as specificed and directed.

Material an labour for construction of valve pit of brick masonry of size 1200 X 1200 x 1200 mm internal dimension complete with Angle Iron 3.15 mm thick MS sheet cover and locking arrangement including excavation and earth work and PCC 1:3:6 type with provision of two caot of synthetic enamal paint over one coat of red oxide primer including demolition of existing vavle pit complete all as specified and directed.

Disconnectind of all electrical connection for taking out unserviceable centrifugel pump of any size from the foundation including other accessories carrying to workshop for repair complete all as specifed and directed. (Note : Spare part measured and paid under relivent items. The cost of transportation to workshop is deeemed to be included in the quoted rate.

M & L for Replacement the defactive part of centrifugel pumps Set are as under cap 20 to 30 HP :-

Impeller of existing size as directed by Engr-in-Charge.

Gland bush including gland packing of existing size as directed by Engr-in-Charge.

Pump shaft of existing size as directed by Engr-in-Charge.

Neck ring any size as directed by Engr-in-Charge.

M & L for Remetaling, grinding, polishing and balancing of shaft for induction motor of capacity 20 to 30 HP. Note : The rate for replacement of bushes, shaft sleeves etc requied for making the shaft functional shall be included in the quoted rate.

Supply and fixing in replacement of ball bearing of induction motor/pump of cap 20 to 30 HP as per existing size complete all as specified and directed.

Supply and fixing in replacement of star coupling suitable for connecting centrifugal motor and pump of capacity upto 30 HP complate all specified and directed.

Supply and fixing in replacement of Tyre coupling suitable for connecting centrifugal motor and pump of capacity upto 30 HP complate all as specified and directed.

Material and labour for rewinding of centrifugal motor of any description, dismantling and strip opening of the motor, removing the old existing burnt windings, cleaning the slots and rewinding of the electric motor of 3 phase, 415 Volts, 50 Hz AC supply with existing gauge copper wire (99.99 % purity) including insulating material such as illumines paper, etherized paper, cotton waste, glass sleeves insulating varnish etc, refixing on existing platform and connected all the electric connections and mechanical connections and testing the complete pumping set up to the entire satisfaction of the Engr-in-Charge for Upto 20 HP Capacity complete all as specified and directed.

Material and labour for rewinding of centrifugal motor of any description, dismantling and strip opening of the motor, removing the old existing burnt windings, cleaning the slots and rewinding of the electric motor of 3 phase, 415 Volts, 50 Hz AC supply with existing gauge copper wire (99.99 % purity) including insulating material such as illumines paper, etherized paper, cotton waste, glass sleeves insulating varnish etc, refixing on existing platform and connected all the electric connections and mechanical connections and testing the complete pumping set up to the entire satisfaction of the Engr-in-Charge for Upto 25 HP to 30 HP Capacity complete all as specified and directed.

Disconnectind of all electrical connection for taking out unserviceable submersible pump set of any size from the bore well including column pipe and other accessories carrying to workshop for repair & back to site complete all as specified and directed. Note : - T&P required for lifting and lowering for submersible pump set column pipe (any number) shall be provided by the contractor. (ii) Necessary safety precautions for workmen shall be the responsibility of the contractor. (iii) The cost of transportation to workshop is deemed to be included in the quoted rate.

M & L Lowering the servicable submersible pump set any size after repair shifted to in its orignal location joint with column pipe and other accessories connecting to all electrical connection testing and commissioning the same complete all as specified and directed. Note : The cost of transportation from workshop is deemed to be included in the quoted rate Necessary safety precautions for workmen shall be the responsibility of the contractor.

M & L for Replacement the defactive part of submersible pump Set are as under :-

Thrust plate of submersible motor of cap upto 25 HP.

Thrust bearing of submersible motor of cap upto 25 HP.

Gun metal bushes for submersible motor of cap upto 25 HP

Remetaling, grinding, polishing and balancing of shaft for submesible motor of capacity upto 25 HP.

Coupling arrangement with key of submersible motor of cap upto 25 HP.

Stainless steel shaft of submersible pump set of cap upto 25 HP.

Impellers for submersible pump set of cap upto 25 HP.

Bowl bush for submersible pump set of cap upto 25 HP

Neck ring for submersible pump set of cap upto 25 HP

M & L for removing old existing burnt windings of the submersible motor cleaning the slots for rewinding, and rewinding the motor with super enamelled copper winding wire superior quality (99.99 % purity) as per existing gauge and size, varnishing, drying, replacement of bearings and assembling the motor of Cap up to 20 HP to 25 HP complete all as specified and directed.

M & L in replacement of sand guard assembely of 20 HP to 25 HP submersible motor as existing make and size all as specified and directed.

M & L in replacement of bush housing set including bush of 20 HP to 25 HP submersible motor as existing make and or size complete all as specified and directed.

M & L replacement of upper housinng set of 20 HP to 25 HP submersible motor as existing make and or size complete all as specified and directed.

M & L replacement of lower housinng set of 20 HP to 25 HP submersible motor as existing make and or size complete all as specified and directed.

M & L in replacement of mechanical seal of 20 HP to 25 HP submersible motor as existing make and or size complete all as specified and directed.

M & L in replacement of seal Guide sleeve of 20 HP to 25 HP submersible motor as existing make and or size complete all as specified and directed.

M & L replacement of startor assembly along with winding wire of 20 HP to 25 HP submersible motor as existing make and or size complete all as specified and directed.

M & L replacement of roter assembly of 20 HP to 25 HP submersible motor as existing make and or size complete all as specified and directed.

M & L in replacement of cable connector sleeve and spring guide plate of 20 HP to 25 HP submersible motor as existing make and size or as directed by Engr-in-Charge.

M & L in replacement of tie rod/tie bolt of 20 HP to 25 HP submersible motor as existing make and size or as directed by Engr-in-Charge.

M & L in replacement of diaphragm along with diaphargm spring of 20 HP to 25 HP submersible motor as existing make and size or as directed by Engr-in-Charge.

M & L in replacement of doom nut and 'O' ring of 20 HP to 25 HP submersible motor as existing make and size or as directed by Engr-in-Charge.

Disconnection and transport to workshop and complete connection after disconnecting of voltage stablizer, opening for repair automatic voltage stabilizer, automatic operation air natural/ oil cooled servo controlled type input voltage 260-440V and output voltage 420V capacity 25 to 250 KVA complete all as specified and as directed. Note : - (i) Cost of transportation of voltage stabilizer to workshop and back after repair complete is deemed to be included in the quoted rate. (ii) Replacement of the parts if any found worn out/defective shall be measured and paid for separately.

Supply and fixing in replacement of dimmer coil with super enameled copper winding wire of existing make and size complete in all respect including varnishing tapping and insulating material to get same capacity of 25 to 250 KVA complate all as specified and directed.

Supply and fixing in replacement of electronic circuit plate complete with DC transformers and shape (PCB cold) upto 250 KVA complate all as specified and directed.

Dismantling of old servo motor and supply and fix new servo motor of upto 250 KVA voltage stabilizer and shape along with all connected accessories and cap complate all as specified and directed.

Dismantling of old carbon bush with carbon holder incl S & F new carbon bush with carbon holder of upto 250 KVA voltage stabilizer and shape complate all as specified and directed.

Supply and fixing in replacement of brass studs fixed for upto 250 KVA voltage stablizer with brass nuts along with all necessary connection complete all as specified for any capacity and directed.

Supply heating and filling of transformer oil EHV grade having dielectric strength not less than 45 KV (Rms) with a 4 mm gap with high viscosity in transformer as per IS-335 of 1983 complete all as specified and directed.

Supply and fixing in replacement of power contractor 3 phase, 3 pole, 415 volts, 50 Hz suitable for operation of a load of capacity of 70 Amps complete all as specified and directed.

Taking down of LT Panel star delta starter of any capacity from its existing position, removing the Burnt contractors, replace the old unserviceable fixed and moving contract, over load coils, no volts coil complete and refixing the starter assembly in its existing position connecting the complete system and making the starter panel functional complete all as specified and directed.

Supply and fix Flat three core PVC insulated & PVC sheathed industrial cable of size 10 Sqmm to 12 Sqmm for submersible pump motor complete all as specified and directed.

Supply and fix Flat three core PVC insulated & PVC sheathed industrial cable of size 16 Sqmm to 35 Sqmm for submersible pump motor complete all as specified and directed.

Supply and fixing in replacement of MCCB 400 Amps 3 pole 415 Volts 36 KA with adjustable thermal and adjustable magnetic settings fixed in repair as per existing at site complete all as specified and directed.

Supply and fixing in replacement of MCCB 250 Amps 3 pole 415 Volts 36 KA with adjustable thermal and adjustable magnetic settings fixed in repair as per existing at site complete all as specified and directed.

Supply and fixing in replacement of MCCB 200 Amps 3 pole 415 Volts 36 KA with adjustable thermal and adjustable magnetic settings fixed in repair as per existing at site complete all as specified and directed.

Supply and fixing in replacement of MCCB 100 Amps 3 pole 415 Volts 36 KA with adjustable thermal and adjustable magnetic settings fixed in repair as per existing at site complete all as specified and directed.

Supply and fixing in replacement of volt meter as per existing size complete all as specified and directed.

Supply and fixing in replacement of indicator lamp assembley complete LED type suitable for the existing system supply voltage for the existing system supply voltage 230V / 440 V AC including taking down old lamp assembly complete all as specified and directed.

M & L for cleaning of underground sump having capacity 45000 liters any type by removing blecahing powder/AI-Tock residue, silt sand, mud, funges etc with steel wire brush and getting out. Cleaning, washing and flushing including writing done/due date of cleaning with synthetic enamelled white paint on black back ground (Black back ground shall be painted with synthetic enamelled black paint), letter n.exc. 10cm in height complete and UG sump should be made smooth by plastering of 1:2 Cm with Dr. Fixit water bound or any othe superier mixture, preventing leakage of inside tank By using special chemical as recommended by experts of OH Tank/ UG Sump as per Manufacturer's instructions and three photographs inside of each Sump and put on Records of Before Cleaning. After cleaning and ater preparing complete. The cost of material and labour For repair of inside tank deemed to be included all as specified and directed.

M & L for cleaning of Overhead Reservoir (OHR) Tank having capacity 32000 liters any type by removing blecahing powder/AI-Tock residue, silt sand, mud, funges etc with steel wire brush and getting out. Cleaning, washing and flushing including writing done/due date of cleaning with synthetic enamelled white paint on black back ground (Black back ground shall be painted with synthetic enamelled black paint), letter n.exc. 10cm in height complete and three photographs inside of each Tank and put on Records of Before Cleaning. After cleaning and ater preparing complete. The cost of material and labour For repair of inside tank deemed to be included all as specified and directed.

Supply and mix calcium Hypo Chlorite granular in factory sealed HDPE container (45 Kg each) decomposing at 177 C, Mol Wt : 142.98, Toxicity: Oral rat LD : 850mg /kg having chlorination concentration level 70% Make- Puri Chlor (Sree Rayalaseema Hi- Strength Hypo Ltd) M/S SVS Aqua Technologies or equivalent in other approved make by E-in-C's Br.

M&L for Testing of collected water sample from NABL lab from Peer baba in period of one quarter from all necessary perameters as directed complete as specified and directed.

Dismantaling /Opening of upper portion of Disel Engine 82.5 to 62.5 KVA DG Set (Make : Greaves/ Kirloskar/ Cummins or any other make) air cooled,turbo charged ,Vertical type for top over hauling, repair/ servicing of engine including taking out rediator /fuel pump,water Pump,Turbo charger etc (Egnine oil and coolent reaquired for this Each Job is deemed to be included in the quoted rate.

(a) Dismantaling/Opening of complete cyllinder head assebly rockers arms assemblypiston head assembly ,sleeves byremoving nuts &bolts for repair complete.

(b) Servicing & washing of complete engine partswith kerosine oil

( c) Re- assembling of engine after replacementof UNSV/defective parts with new parts as listed in given below per Each Job shall be deemed to be included in this rates and testing of engineas per company recommendation after reassembling all parts as directed to the satifaction of the Engr-in -Charge

Note : Repair and Transportation (BY JCB / HYDRA OR ANY OTHER MEANS) charge for carrying out repair & reinstall on same installation back shall be deemed to be included in this rates

Supply inreplacement of following parts given below rates shall be deemed to be above Each Job included .

i) Valve Exhaust

ii)Valve inlet

iii)insert Valve Seat

iv)Guide Valve

v)Cup Injector

vi) Fip Element

vii) Gasket Set

viii) Hose Pipe

ix) Fuel Filter

x) Lubrication Oil Filter

xi) Super By Pass Fillter

xii) Hose Clip Set

xiii) Piston set Complete

xiv Ring Set Complete

xv) Cyllinder Linner

xvi) Connecting Rod Bearing

xvii) Gasket Set Cyllinder Head

xvii) Callibration of Fuel Pump

xix )Head Repair Work

xx ) Callibration of injectors of Nozzels

xxi ) Lubrication Oil Pump

xxii ) O ' Ring Set Complete

xxiii) Set of Fuel Flexible Pipe

xxiv) Stem Seal

Dismantaling /Opening of upper portion of Disel Engine 40 KVA to 30 KVA (Make : Greaves/ Kirloskar/ Cumiuns or any other make) air cooled,turbo charged ,Vertical type for top over hauling, repair/ servicing of engine including taking out rediator /fuel pump,water Pump,Turbo charger etc (Egnine oil and coolent reaquired for this Each Job is deemed to be included in the quoted rate.

(a) Dismantaling/Opening of complete cyllinder head assebly rockers arms assemblypiston head assembly ,sleeves by removing nuts &bolts for repair complete.

(b) Servicing & washing of complete engine partswith kerosine oil

( c) Re- assembling of engine after replacementof UNSV/defective parts with new parts as listed in given below Per Each Job shall be deemed to be included in this rates and testing of engineas per company recommendation after reassembling all parts as directed to the satifaction of the Engr-in -Charge

Note : Repair and Transportation (BY JCB / HYDRA OR ANY OTHER MEANS) charge for carrying out repair & reinstall on same installation back shall be deemed to be included in this rates

Supply & fixing in replacement of following parts given below rates rates shall be deemed to be above Each Job included .

i) Valve Exhaust

ii)Valve inlet

iii)insert Valve Seat

iv)Guide Valve

v)Cup Injector

vi) Fip Element

vii) Gasket Set

viii) Hose Pipe

ix) Fuel Filter

x) Lubrication Oil Filter

xi) Super By Pass Fillter

xii) Hose Clip Set

xiii) Piston set Complete

xiv Ring Set Complete

xv) Cyllinder Linner

xvi) Connecting Rod Bearing

xvii) Gasket Set Cyllinder Head

xvii) Callibration of Fuel Pump

xix )Head Repair Work

xx ) Callibration of injectors of Nozzels

xxi ) Lubrication Oil Pump

xxii ) O ' Ring Set Complete

xxiii) Set of Fuel Flexible Pipe

xxiv) Stem Seal

Servicing of DG Sets of capacity 82.5 KVA of make (Make : Greaves/ Kirloskar/ Cummins or any other make) by the authorised Engineer of respective manufacturer of DG Set continous operational condition including the following checkings all as specified and directed by Engr-in -charge (Egnine oil and coolent reaquired for this Each Job is deemed to be included in the quoted rate.

(i) Removing the existing engine oil, clean the oil sump and refilling with required quantity of new engine oil 20W40 & coolant upto top.

(ii) Checking of fan motor hub

(iii) Checking exhaust and inlet manifold belt and cap screw

(iv)Cleaning of radiator inside and out side thoroughly with solution (caustic soda) to the entire satisfaction of Eng-in-charge by removing and re-fixing in original position after cleaning.

(v) Checking and adjusting injector and valves, tappet and replace the gasket including cost of gasket.

(vi) Cleaning fuel inlet connections and screw,

(vii) Checking of vibration damper and rectified.

(viii) Servicing of turbocharger by checking, leakage tightening of mounting screws & nuts and replace oil.

(ix) Checking water temperature safety control

(x) Checking and correcting up impeller of water pump for excess play.

(xi) Servicing of governer and Changing of governor oil.

(xii) Checking and adjusting all fan belt.

(xiii) Any other check as per manufacturer`s instructions

Note:- Necessary spare parts required if any will be measured and paid under relevant items

S & F in repairs Kit, fuel filter and ring

(b) S & F in repairs Element for Lubrication oil filter.

(c)S & F in repairs Kit, Element of super bypass filter.

(d) S & F in repairs Seal, O Ring and Air cleaner.

(e ) S & F in repairs Kit Conversion

(f )S & F in repairs Gasket, Rocker lever cover

All as per item no.3 above but Diesl Engine of 62.5/63 KVA DG Set.

(a) S & F in repairs Kit, fuel filter and ring

(b) S & F in repairs Element for Lubrication oil filter.

(c)S & F in repairs Kit, Element of super bypass filter.

(d) S & F in repairs Seal, O Ring and Air cleaner.

(e ) S & F in repairs Kit Conversion

(f )S & F in repairs Gasket, Rocker lever cover

All as per item no.3 above but DG Sets of Capacity 40/30 KVA DG set

(a) S & F in repairs Kit, fuel filter and ring

(b) S & F in repairs Element for Lubrication oil filter.

(c)S & F in repairs Kit, Element of super bypass filter.

(d) S & F in repairs Seal, O Ring and Air cleaner.

(e ) S & F in repairs Kit Conversion

(f )S & F in repairs Gasket, Rocker lever cover

M&L for Rewinding of armature of Dynamo/alternators 12V/24V volts with `F' class copper wire to match existing gauge including dismantling of old coil , cleaning thoroughly winding with super enameled copper wire of existing size and gauge,varnishing, drying etc and fixed with dynamo/alternator properly tesing and commissioning all as specified all and directed by Engr-in-Charge.

S & F repair radiator hoses of size 40mm dia or as per existing dia and 60 cm length for any capacity of DG set including jublee clip, clamp nuts etc are properly fixed and connected.as directed to the satifaction of the Engr-in -Charge

S & F in replacement of flexible pressure pipe for lubricant size of 60 cm length for oil and fuel connection for complete suitable for 40/62.5/82.5 KVA Engineas directed to the satifaction of the Engr-in -Charge

Supply and filling Engine oil 20W/40f make (Castroll/Kirloskar/HP) complete all as specified & directed

S& Fill distilled water packed in sealed gallan of 5 Ltrs complete all as specified & directed

Supply and filling water coolant(diluted)in radiator (make volve line or equivalent) including removal of old water/coolant, complete all as specified & directed

Dismantling and removing of water pump assembly of any capacity any type of DG Set complete from the engine,repair/overhauling the same by replacing tornout components like bearing,impeller,bushes, oil seal,water seal,gaskets etc. reassembling,refixing and testing complete all as specified & directed

M & L for Repair/overhauling of self starter 12V/24V including replacement of worn out clutch assembly,bush,spring,plunger assembly, solenoid switch,carbon brushes,brush spring etc.as directed to the satifaction of the Engr-in -Charge for the 40/62.5/82.5 KVA DG Set complete all as specified & directed

M & L for replacement of totally damaged self starter 12V/24V complete assembly suitable for any capacity of DG Set complete all as specified & directed

M & L for Repair/overhauling of dynamo including replacement carbon, brushes holder, spring, commutator /slipring assembly bearing, regulator etc. of any make, type and capacity.complete all as specified & directed

Supply in replacement of electrically operated fuel shut down valve assembly complete testing and commissioning including dismantling and removal of old U/S valves of any capacity DG set. complete all as specified and directed.

M & L for Servicing/repairs of AMF panel complete including cleaning resetting/adjustment of relays,calibration of time delay relays, checking and replcement of diods, if required ,resistors contactor etc. complete for any make/type and capacity of DG sets. complete all as specified and directed.

M & L for Disconnecting and dismantling the alternator unit of 82.5 KVA DG Set from the base plate of the DG set and transporting to workshop for repair, dismantling the unit, further separating the armature from the startor carefully, cutting and taking out the burnt windings of the alternator carefully, cleaning the slots and , duly applying the insulation and assembling the stampings inserting in position in the startor including applying slot insulation and rewinding of the alternator startor winding with super enameled copper conductor of same gauge and same number of turns as that of existing one including replacement of carbon brushes tapping the windings and bringing out the coil conections for production of 3 phase 415 volt 50 HZ AC supply and preheating the windings and applying insulating varnish and drying the windings in oven and assembling the unit and transporting back to installation and fixing on base plate and coupling with the DG set and testing complete all as specified and directed.

M & L for Disconnecting and dismantling the alternator unit of 62.5 KVA DG Set from the base plate of the DG set and transporting to workshop for repair, dismantling the unit, further separating the armature from the startor carefully, cutting and taking out the burnt windings of the alternator carefully, cleaning the slots and , duly applying the insulation and assembling the stampings inserting in position in the startor including applying slot insulation and rewinding of the alternator startor winding with super enameled copper conductor of same gauge and same number of turns as that of existing one including replacement of carbon brushes tapping the windings and bringing out the coil conections for production of 3 phase 415 volt 50 HZ AC supply and preheating the windings and applying insulating varnish and drying the windings in oven and assembling the unit and transporting back to installation and fixing on base plate and coupling with the DG set and testing complete all as specified and directed.

Disconnecting and dismantling the alternator unit of 30 to 40 KVA DG Set from the base plate of the DG set and transporting to workshop for repair, dismantling the unit, further separating the armature from the startor carefully, cutting and taking out the burnt windings of the alternator carefully, cleaning the slots and , duly applying the insulation and assembling the stampings inserting in position in the startor including applying slot insulation and rewinding of the alternator startor winding with super enameled copper conductor of same gauge and same number of turns as that of existing one including replacement of carbon brushes tapping the windings and bringing out the coil conections for production of 3 phase 415 volt 50 HZ AC supply and preheating the windings and applying insulating varnish and drying the windings in oven and assembling the unit and transporting back to installation and fixing on base plate and coupling with the DG set and testing complete all as specified and directed.

Supply in replacement of diode assembly complete suitable to match the existing one of 82.5 KVA alternator excitor unit. complete all as specified and directed.

Supply in replacement of diode assembly complete suitable to match the existing one of 62.5/40 KVA alternator excitor unit. complete all as specified and directed.

Supply in replacement of PVC insulated battery lead with 16 Sq.mm copper conductor cable of length 2 mtr with copper/brass clamps and lugs for fixing on battery terminals and self starter complete as specified and as directed.

Supply in replacement of rectifiers for alternators suitable for Gensets upto 40/62.5/82.5 KVA capacity complete as specified and as directed.

Supply in replacement of water temperature gauge complete with cable and accessories at the last range 0 to 150 degree centigrate complete as specified and as directed.

Supply in replacement of oil temp gauge as per existing site requirement complete as specified and as directed.

Supply in replacement of oil pressue gauge as per existing site requirement complete as specified and as directed.

M & L for Dismantling the defective Fuel Injector Assembly of any capacity from the existing foundation and engine including taking down all electrical connections transporting to approved authorised workshop, after setting up opening the complete, connector plate, gasket & complete overhauling re- assembling the Fuel Injector after transporting back to site re-installing carrying out alignment of complete DG set reconnecting up all electrical connections testing and commissioning complete the following capacity of DG set (Note:- (a) Rate quoted shall be deemed to be inclusive making good the distrubed surfaces (b) The DG set shall be tested for the satisfaction of Engr -in -charge to achive designed parameters.

82.5/62.5 KVA DG

40 KVA DG

Attending compliant and inspection/trouble shooting/repair the AMF panel of any rating 3 phase 415V 50Hz AC supply including checking the serviceability of individul components, cleaning / tightning of loose connections, identification of defective parts including replacement of minor parts like jumper conneting cables, connectors, lugs, fastners etc, complete as specified and as directed. Note : Defective parts / repair work to individual parts shall be measured and paid separately.

Supply and replacing the following spares including connecting into electric circuit, testing and commissioing.

Solonoid valve 24V of suitable for 62.5 KVA to 82.5 KVA

Solonoid valve 12/24V of suitable for 30 KVA to 40 KVA

Changer relay AC 230V suitable for DG set AMF panel of rating 30 KVA to 82.5 KVA

anger relay DC 24V suitable for DG set AMF panel of rating 30 KVA to 82.5 KVA

Time relay AC 230V suitable for DG set AMF panel of rating 30 KVA to 82.5 KVA

Time relay DC 24V suitable for DG set AMF panel of rating 30 KVA to 82.5 KVA

Coil 230/430V +/- 5% AC 50Hz

Supply and fixing in replacement of Digital volt meter as per existing size complete all as specified and directed.

Supply and fixing in replacement of Digital Amp meter as per existing size complete all as specified and directed.

Supply and fixing in replacement of Digital Frequency meter as per existing size complete all as specified and directed.

Supply and fixing in replacement of indicator lamp assembly complete LED type suitable for the existing system supply voltage for the existing system supply voltage 230V / 440 V AC including taking down old lamp assembly

Supply and fixing in replacement of AVR unit of 82.5 KVA for matching the existing AVR unit, complete all as specified and directed by Eng-in charge. Make:- Kirloskar/Cummins/Ashok Leyland/Stanford.

Supply and fixing in replacement of AVR unit of 62.5 KVA to 40 KVA for matching the existing AVR unit, complete all as specified and directed by Eng-in charge. Make:- Kirloskar/Cummins/Ashok Leyland/Stanford.

S & F in repair battery terminal brass superior quality suitable for 180 AH 12 Volts Battery complete all as specified and directed.

S&F free lead acid battery 12 volts 180 AH complete all as specified and directed.

M&L for servicing/ cleaning of MS diesel tank of DG set 82.5 KVA by draining out the diesel from tank, cleaning the tank with soap water/ suitable solution and painting the external surface with one coat of synthetic enamel paint of existing colour including repalcement of drain valve, outlet pipe complete all as specified and as directed.

M&L for servicing/ cleaning of MS diesel tank of DG set 62.5/40/30 KVA by draining out the diesel from tank, cleaning the tank with soap water/ suitable solution and painting the external surface with one coat of synthetic enamel paint of existing colour including repalcement of drain valve, outlet pipe complete all as specified and as directed.

S&F in replacement, fan belt suitable for 40/30 KVA DG set complete all as specified and as directed.

S&F in replacement, fan belt suitable for 62.5 KVA DG set complete all as specified and as directed.

S&F in replacement, fan belt suitable for 82.5 KVA DG set complete all as specified and as directed.

M & L for Dismantling/ taking down complete radiator assembly of DG set 82.5 KVA and transporation to market for repair by :- (i) Opening the radiator assembly with brazing/ welding for repair/ services. (ii) Cleaning of all water tube with diluted solution of HCL & cleaning with water preasure & removing the sludge and dust from inside the tank by flushing out. (iii) Repair of fins by soldring/ brazing. (iv) Repair of bottom brass water tank by soldring/ brazing. (v) Repair of radiator hose assembly. (vi) Fixing the complete radiator assembly to its orignal position and testing complete

M & L for Dismentling/ taking down complete radiator assembly of DG set 62.5 KVA and transporation to market for repair by :- (i) Opening the radiator assembly with brazing/ welding for repair/ services. (ii) Cleaning of all water tube with diluted solution of HCL & cleaning with water preasure & removing the sludge and dust from inside the tank by flushing out. (iii) Repair of fins by soldring/ brazing. (iv) Repair of bottom brass water tank by soldring/ brazing. (v) Repair of radiator hose assembly. (vi) Fixing the complete radiator assembly to its orignal position and testing complete

Dismentling/ taking down complete radiator assembly of DG set 40/30 KVA and transporation to market for repair by :- (i) Opening the radiator assembly with brazing/ welding for repair/ services. (ii) Cleaning of all water tube with diluted solution of HCL & cleaning with water preasure & removing the sludge and dust from inside the tank by flushing out. (iii) Repair of fins by soldring/ brazing. (iv) Repair of bottom brass water tank by soldring/ brazing. (v) Repair of radiator hose assembly. (vi) Fixing the complete radiator assembly to its orignal position and testing complete

Supply in replacement of Genset Radiators with complete assembly Optimum quality, durability and rugged designs and well tested, well safety, High heat transfer, high efficiency and economical design complete testing and commissioning as specified and directed by Engr.in-charge including dismantling and removal of old U/S Radiators of 82.5 to 62.5 KVA DG set.

Supply , laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavu duty aluminium conductor LT 1100 V grade cross sectional area 70 sqmm 3.5 core, complete all as specified and directed by Engineer-in-Charge

Supply , laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavu duty aluminium conductor LT 1100 V grade cross sectional area 50 sqmm 3.5 core, complete all as specified and directed by Engineer-in-Charge

Supply , laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavu duty aluminium conductor LT 1100 V grade cross sectional area 35 sqmm 3.5 core, complete all as specified and directed by Engineer-in-Charge

Supply , laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavu duty aluminium conductor LT 1100 V grade cross sectional area 25 sqmm 4 core, complete all as specified and directed by Engineer-in-Charge

Supply , laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavu duty aluminium conductor LT 1100 V grade cross sectional area 16 sqmm 2 core, complete all as specified and directed by Engineer-in-Charge

Supply , laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavu duty aluminium conductor LT 1100 V grade cross sectional area 10 sqmm 2 core, complete all as specified and directed by Engineer-in-Charge

Supply and laying GI Tubing Light grade 50 mm Bore dia as Cable Protection fixied on walls/ poles by using the suitable size clamps, nuts, bolts etc or laid in trenches complete all as specfied and directed.

Supply and laying GI Tubing Light grade 80 mm Bore dia as Cable Protection fixied on walls/ poles by using the suitable size clamps, nuts, bolts etc or laid in trenches complete all as specfied and directed.

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 m in depth in a soft/Hard soil for laying underground cables/ errection of steel tubular poles / stay pit etc all as directed by Engr-in-charge.

Returning, filling in incl spreading,levelling watering and well ramming in layer n exc .25 cm in soil each layer complete specified and directed by Engr-in-Charge.

Removing excavated surplus material to a distance n.exc 50 m and depostimg where directed at alevel n exc. 1.5 m above the starting point in any type of soil complete all as specified and directed by Engr-in-Charge.

M & L for sand cushioning with a layer of sand 80 mm thick before laying of cable and 150 mm thick after laying of cable in trenches complete all as specified and directed.

M & L for Brick covering with width equal to length of brick as mechanical protection to cables with well burnt sub class 'B' (old size) bricks laid dry flat, complete all as specified and directed.

S&F in replacement of Change over switch off load type with enclosure, conforming IS 13947 part I & III 415V, 4 pole of rating 100 amps, including taking out unservicable one complete all as specified and directed by Engineer-in -Charge.

S&F in replacement of Change over switch off load type with enclosure, conforming IS 13947 part I & III 415V, 4 pole of rating 200 amps, including taking out unservicable one complete all as specified and directed by Engineer-in -Charge.

S&F in replacement of Change over switch off load type with enclosure, conforming IS 13947 part I & III 415V, 4 pole of rating 250 amps, including taking out unservicable one complete all as specified and directed by Engineer-in -Charge.

S&F MCCB four pole 200 Amps, 35 KA fixed thermal & fixed magnetic setting including 4 spreder link set of same make as that of MCCB for connection, and lugs as required all as complete as specified and directed.

S&F MCCB four pole 125 Amps, 35 KA fixed thermal & fixed magnetic setting including 4 spreder link set of same make as that of MCCB for connection and lugs as required all as complete as specified and directed.

S&F MCCB four pole 63 Amps, 25 KA fixed thermal & fixed magnetic setting including 4 spreder link set of same make as that of MCCB for connection and lugs as required all as complete as specified and directed.

M & L for Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 M below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt , earth lead of galvanised iron strip of size 25x4 mm connectd to GI earth plate elcectrode by means of bolts, nuts, check nuts and washers of galvanised iron and thimbles and other end of earth wire connected to main switch board and protected by galvanised iron pipe medium grade 15mm bore and 20mm bore light gradeGI pipe with funnel and wire mesh for watering including necessary excavation and earth works. PCC Chamber in cement concrete 1:3:6 type C-2 & RCC cover in M-20 (Design mix ) and all as shown in Electrical Plate No. 3 of SSR ( Part-I) of 2009 and testing on completion.

M & L for Attending compliant / servicing / repair the servo controlled voltage stabilizer of capacity 25 KVA to 200KVA single/3 phase, (having input voltage of 160V to 260V and out put voltage stabilized at 220+9% for single phase and 300 to 460V input (Approx) and out put voltage stabilized at 430+ 1% V for 3 phase) with balanced / unbalanced load including checking the serviceability of individul components, cleaning / tightning of loose connections, including replacement of minor parts like jumper conneting cables, connectors, lugs, fastners etc complete all as specified and directed.

M & L for Taking out/removing the defective barrier assembly/ dimmer coil from the volatage stabilizer by manually/using chain pully block, transporting to workshop, removing the burnt windings cleaning and rewinding, with existing size super enamelled copper wire, varnishing, heating and transporting to site for refixing for the following capacity of stabilizers. Note : Old burnt copper winding will be measured and issued to contractor under Sch of credit.

(a) 50KVA to 75KVA single/3 phase

(b) 100KVA to 250KVA single/3 phase

Filtration of transformer oil of Voltage Stablizer oil type up to 150 KVA capacity installed at different sub stations/locations using filtration plant , dehydration and improving di-electric strength of the oil to withstand 40 KV for one minute including testing of oil as specified and directed. NOTE : Stablizer oil test kit shall be provided by the contractor at site for testing of oil.

Filling in with new transfor oil for Voltage stabilizer oil EHV grade low viscosity of approved make as per IS-335 of 1992 and die-electric strength 20 KV when tested at 1mm gap incl submission of certificate fro IS approved lab for desired value of die-electric strength complete all as specified.

Cleaning the internal surfaces of volage stabilizer to free from dust/sediments/rust, removing transformer oil (where ever exists) and refilling, refixing the barrier assembly including connecting all electric/electroni/mechanical components, testing and commissioing for the following sizes:

(a) 50KVA to 75KVA single/3 phase

(b) 100KVA to 200KVA single/3 phase

M & L for Disconnecting the input/output electri supply 3 phase and Neutral AC 50Hz/single phase conections, removing the top cover for taking out defective voltage stabilizer including disconnecting connected electri/electronic/mechanical components of the following capacity stabilizers for repair after repair refixing the same position complete etc all as specified and directed. Note : Defective parts/ repair work to individual mparts shall be measured and paid separately.

50KVA to 75KVA single/3 phase

100KVA to 120KVA single/3 phase

Supply and fixing in repair following spares including removing of respective defective spares of servo controlled Voltage stabilizer single/3 phase having standard input/out put voltages.

(a) Push button switch

(b) Auto manual switch

(c) DPDT switch

(d) Micro switch

(e) Panel phase indication lamp

(f) Potential meter

(g) High low indicator lamp

(h) Voltmeter 0 to 500 Volts

(j) Ampere meter 20 to 100Amps

(k) Current transformer 5VA to 10VA class 0.5 of rating 30, 50, 60, 75, 100, 150, 200/5A

(l) Electronic circuit card including Control drive transformer with wiring.

(m) PCB Holder

(n) Rotary switch 5A for 3 phase.

(n) Servomotor for 25 KVA to 50 KVA Voltage stabilizer

(o) Servo motor for 63 KVA to 200 KVA Voltage stabilizer

(p) Carbon brush

(q) Carbon brush holder with spring

(r) Drive assembly upto 25KVA per phase

(s) Drive assembly 50KVA to 200KVA per phase

(t) Toggle switch single pole one way 5Amps

(u) Motor gear pinion

(v) Digital Control panel with circuit board for High/Low voltage cut suitable upto 50 KVA 3 phsae voltage stabilizer.

(w) Digital Control panel with circuit board for High/Low voltage cut suitable for 63 to 200 KVA 3 phsae voltage stabilizer.

Dismantling from electric circuit cleaning to free from dust/rust/oil/grease etc preparation of external surfaces and spray painting with two coat of synthetic enamel paint of approved colour for Voltage Stabilizer and refixing the same with new thimble, washers etc all as specified and directed.

Material and labour for Outdoor type factory made feeder pillar box canopy type of size 0.45 x 0.75 x 0.40 M depth made out of CRCA sheet 3.15 mm thick, suitable 04 Nos busbar size 20 x 5 mm having locking arrangement, provn of suitable hole at bottom for incoming and outgoing UG cables incl painting with 2 coat of powder coated paint over a coat of red oxide promer on exterior and interior faces of Bus bar chamber, errection of Bus bar chamber with PCC 1:2:4 type B2 and fixing and connection including earth work, taking down and provn of suitable frame at bottom made out of angle iron of size 40 x40 x6mm thick complete all as specified and directed by Engineer-in-Charge

S & F in repair battery terminal brass superior quality suitable for 180 AH 12 Volts Battery complete all as specified and directed by Engineer-in-Charge

Supply and fixing in replacement of ignition switch and key of 82.5 KVA DG Set complete all as specified and directed by Engineer-in-Charge

Supply and fixing in replacement of ignition switch and key of 62.5/40 KVA DG Set complete all as specified and directed by Engineer-in-Charge

Supply and fixing in replacement of AVR unit of 82.5 KVA for matching the existing AVR unit, complete all as specified and directed by Eng-in charge. Make:- Kirloskar/Cummins/Ashok Leyland/Stanford.

Supply and fixing in replacement of AVR unit of 62.5 KVA to 40 KVA for matching the existing AVR unit, complete all as specified and directed by Eng-in charge. Make:- Kirloskar/Cummins/Ashok Leyland/Stanford.

S&F in replacement of contactor suitable for AMF panel contactor MNX 25 3pole 240V as per existing contactor of site complete all as specified and directed by Eng-in charge.

S&F in replacement of contactor suitable for AMF panel contactor MNX 16 3pole 240V as per existing contactor of site complete all as specified and directed by Eng-in charge.

S&F free lead acid battery 12 volts 180 AH complete all as specified and as directed by Engr-In-Charge.

M&L for servicing/ cleaning of MS diesel tank of DG set 82.5 KVA by draining out the diesel from tank, cleaning the tank with soap water/ suitable solution and painting the external surface with one coat of synthetic enamel paint of existing colour including repalcement of drain valve, outlet pipe complete all as specified and as directed.

M&L for servicing/ cleaning of MS diesel tank of DG set 62.5/40 KVA by draining out the diesel from tank, cleaning the tank with soap water/ suitable solution and painting the external surface with one coat of synthetic enamel paint of existing colour including repalcement of drain valve, outlet pipe complete all as specified and as directed.

S&F in replacement of MCCB, three pole, 160 Amp 415 volts, 50 Hz breaking capacity not less than 25 kA with adjustable thermal and adjustable magnetic protection release with spreader links, Ics = 100% Icu complete all as specified and as directed

S&F in replacement of MCCB, three pole, 125 Amp 415 volts, 50 Hz breaking capacity not less than 25 kA with adjustable thermal and adjustable magnetic protection release with spreader links, Ics = 100% Icu complete all as specified and as directed

S&F in replacement of MCCB, three pole, 100 Amp 415 volts, 50 Hz breaking capacity not less than 25 kA with adjustable thermal and adjustable magnetic protection release with spreader links, Ics = 100% Icu complete all as specified and as directed

S&F in replacement, fan belt suitable for 40 KVA DG set complete all as specified and as directed.

S&F in replacement, fan belt suitable for 62.5 KVA DG set complete all as specified and as directed.

S&F in replacement, fan belt suitable for 82.5 KVA DG set complete all as specified and as directed.

M & L for Dismantling/ taking down complete radiator assembly of DG set 82.5 KVA and transporation to market for repair by :- (i) Opening the radiator assembly with brazing/ welding for repair/ services. (ii) Cleaning of all water tube with diluted solution of HCL & cleaning with water preasure & removing the sludge and dust from inside the tank by flushing out. (iii) Repair of fins by soldring/ brazing. (iv) Repair of bottom brass water tank by soldring/ brazing. (v) Repair of radiator hose assembly. (vi) Fixing the complete radiator assembly to its orignal position and testing complete

M & L for Dismantling/ taking down complete radiator assembly of DG set 62.5 KVA and transporation to market for repair by :- (i) Opening the radiator assembly with brazing/ welding for repair/ services. (ii) Cleaning of all water tube with diluted solution of HCL & cleaning with water preasure & removing the sludge and dust from inside the tank by flushing out. (iii) Repair of fins by soldring/ brazing. (iv) Repair of bottom brass water tank by soldring/ brazing. (v) Repair of radiator hose assembly. (vi) Fixing the complete radiator assembly to its orignal position and testing complete

M & L for Dismantling/ taking down complete radiator assembly of DG set 40 KVA and transporation to market for repair by :- (i) Opening the radiator assembly with brazing/ welding for repair/ services. (ii) Cleaning of all water tube with diluted solution of HCL & cleaning with water preasure & removing the sludge and dust from inside the tank by flushing out. (iii) Repair of fins by soldring/ brazing. (iv) Repair of bottom brass water tank by soldring/ brazing. (v) Repair of radiator hose assembly. (vi) Fixing the complete radiator assembly to its orignal position and testing complete

S&F in replacement of Change over switch off load type with enclosure, conforming IS 13947 part I & III 415V, 4 pole of rating 100 amps, including taking out unservicable one complete all as specified and directed by Engineer-in -Charge.

S&F in replacement of Change over switch off load type with enclosure, conforming IS 13947 part I & III 415V, 4 pole of rating 200 amps, including taking out unservicable one complete all as specified and directed by Engineer-in -Charge.

S&F commissioning and testing of CPRI approved outdoor cubical type LT panel IP-54 Protection for outdoor shell and IP- 42 for inner shall,suitable for 415V, 3 phase, 4 wire 50Hz, AC supply system fabricated fromstainless steel totally enclosed,Dust,Weather & vermin proof, 3.15 mm thick for outer shell and 2mm thick for inner shell having MS section not less then 50x50x6 mm thick having TPN aluminium busbar mounted in porcelin insulator duly drilled hole for cable connection including front and rear side opening with locking arrangement and provn for incoming and outgoing cables with glands including control wiring with minimum 1.5 sqmm PVC insulated copper conductor for measuring of voltage, amp with indicators RYB, painting with two coat of smoke grey synthetic enamelled paint over a coat of red oxide primer complete all as specified and directed by Engrineer-in-Charge. Note:- LT panel shall be mounted on brickwork in CM 1:4 not less than 60 cm above ground level with suitable foundation, rendering 15 mm in CM1:6 and two coates of cement base paint and the rates shall be inclusive in the quoted rate. (Minimum size: 1.5*2.5*4.5 in Feet )

Incoming:

MCCB 250 Amp 4 pole 38 KA Adjustable Thermal & Fixed Magnetic setting , Ics = 100% of Icu - 01 Nos

Alum bus bar 400 Amp TPN - 01 Set

Indicator lamp LBD type (RYB) complete with bakelite fuse fitting- 01 set

Outgoing

MCCB 3 Pole, 100 Amp, 20 KA, Adjustable Thermal & Fixed Magnetic setting , Ics = 100% of Icu- 02 Nos

MCCB 3 Pole, 63 Amp, 20 KA, Adjustable Thermal* & Fixed Magnetic setting , Ics = 100% of Icu- 02 Nos

On Load change over switch front operated suitable for 4 pole 415V of capacity 315 Amp

Supply in replacement of 24 Volt Relay ,taking down and reconnecting up all electrical connections testing and commissioning complete as directed to the satifaction of the Engr-in -Charge

Supply in replacement of 12 Volt Relay ,taking down and reconnecting up all electrical connections testing and commissioning complete as directed to the satifaction of the Engr-in -Charge

Supply and fixing in replacement of Didital volt meter as per existing size complete all as specified and directed.

Supply and fixing in replacement of Digital Amp meter as per existing size complete all as specified and directed.

Supply and fixing in replacement of Digital Frequency meter as per existing size complete all as specified and directed.

Supply and fixing in replacement of indicator lamp assembly complete LED type suitable for the existing system supply voltage for the existing system supply voltage 230V / 440 V AC including taking down old lamp assembly complete all as specified and directed.

Dismantling and servicing of cooling appliances including cleaning, painting, necessary test of leakage by nitrogen gas, brazing, compressed air wash and make the system functional complete all as specified for Acs window/ Split type of any capacity.complete all as specified and directed.

All as per item No 187 above but for Water Cooler of any capacity

All as per item No 187 above but for Refrigerator of any capacity

All as per item No 187 above but for Deep freezer of any capacity

Removing the unserviceable fan motor from window/Split AC any capacity removing the burnt out winding wire from slots, clean slots with emery paper and rewind the same with superior quality copper wire insulate properly and bringing back and fixing in position and testing and commissioning complete all as specified and directed.

All as per item No 191 above but for Water Cooler upto 150 Ltrs capacity

Replacement of unserviceable air Filter for Split AC.

S&F Relay of Refrigerator of the same make and type.

S&F for Disconnect the suction and discharge line to the unserviceable compressor, replace with the new compressor brought from the factory of the same make connect the refregerent lines systems flushing vacuumising of the entire system arrest all leakages including testing and commissioning for Split AC 1.5 ton capacity complete all as specified and directed.

All as per item No 195 above but for Water Cooler above 80 LTR upto 150 Ltrs capacity

All as per item No 195 above but for Water Cooler 40 to 80 Ltrs capacity

All as per item No 195 above but for Refrigerator 165 to 185 Ltrs capacity

All as per item No 195 above but for Deep freezer 165 to 185 Ltrs capacity

Replacement of unserviceable thermostat AC up to 1.5 Ton

All as per item No 199 above but for Water Cooler upto 150 Ltrs capacity

All as per item No 199 above but for Refrigerator up to 310 Ltrs capacity

Remove the unserviceable fan blade from the condenser cooling motor and replace with new fan blade of same size and type for Water Cooler any capacity

All as per item No 203 above but for Air conditioners up to 1.5 Ton.

S&F Blower assembly of suitable type for Air conditioners up to 1.5 Ton.

Replacement of unserviceable float valve with new brass Float valve of water cooiers complete any make 15 mm bore complete all as specified and directed.

Flushing & vacuumising the system and charging of necessary refrigerent at required quantity for Window AC/Split AC Up to 1.5 Ton complete all as specified and directed.

All as per item No 207 above but for Refrigerators of any capacity.

All as per item No 207 above but for Water coolers of any capacity.

Replacement of unserviceable Condenser AC up to 1.5 Ton complete all as specified and directed.

All as per item No 210 above but for Refrigerators of any capacity.

All as per item No 210 above but for Water coolers of any capacity.

S&F in repair 40 amp, single pole and neutral, socket outlet, with 2 pole and earth, metal enclosed plug top in power coated CRCA steel sheet enclosure recess mounted with chained metal cover for the socket outlet with and including one number single pole 'C' series MCB 16 amp as required. complete all as specified and directed.

M/S Darshan Kumar

M/S KALSI ENGINEERS AND CONTRACTORS