REPAIR TO SUNKEN FLOOR ROOF TREATMENT JOINERY WORK RENOVATION OF KITCHEN AND TOILET ETC AT OFFR MD ACCN IN MAUDE ROAD STN ROAD KABUL LINE MAP FAFA QTRS AND POULTRY FORM AREA UNDER AOR OF AGE BR II UNDER GE NORTH DELHI CANTT 10

Amount

Complete removal of old roof treatment including cement mortar bedding and removing debries out side MOD land, (except mudfushka), complete all as specified and directed.

M&L for 15mm thick cement plaster over the concrete / brick roof surfaces in cement mortar 1:4 mixed with liquid water proofing compound @ 200ml per bag WPC (liquid type), surface finished even and smooth without using extra cement all as specified and directed. Note :- Water proofing additive shall be measured and paid separately.

M&L for preparation of roof top surfaces by cleaning all the dust and loose material by brush/blower/Grinder including removing of vegetation/plantation from the surface and providing and applying single component elastic cold applied polyurethane modified acrylic roofing system, co elastic technology (CET) based on modified polyurethane and fully fibre reinforced, having Sun Reflectivity index (SR) of 109 on top of concrete roof surfaces. All cracks up to 3mm at corner joints, channel and parapets should be treated with crack seal. Applying three coats including one coat of primer of ShaliUrethane BTD/ Sikalastic 560/ smart care damp proof-ultra having coverage @ min 0.75kg/m2 and dilution up to 10% and laying reinforced fiber net and applying two coats (without dilution) of shaliUrethane BTD/Sikalastic 560/smart care damp proof ultra @ total consumption 2 kg/m2 in two coats for maintaining minimum dry film thickness 1.5mm and elongation at break of free film of approx 350%. The materials shall be applied with brush or roller, complete in all respect as per the direction of Engineer-in-charge/Consultant Note :6 Hrs interval between two coat will be maintained. All auxiliary and accessories involved during application should be supplied by single manufacturer as a part of system. Make:as approved by GE. Note:- (i) Application of water proofing treatment will be done by Authorised Applicator duly approved by GE in writing. (ii) The water proofing treatment shall be carried out by the manufacturer or their authorized applicators (iii) 5% amount of the total amount of water proofing treatment shall be retained as a guarantee and shall be released after 10 years. However, contractor may deposit the FDR of same amount in favour of GE. If contractor fail to rectify the defect pointed out during this period in writing, the defect shall be got rectified at contractor' risk and cost and the payment shall be made from the amount kept reserved or by encashing the FDR deposited by the contractor as guarantee. The contractor's quoted rates for this item shall deemed to be inclusive of this aspect

Supply only liquid water proofing compound complete all as specified and as directed. Make: FOSROC or equiavalent as approved by GE.

Racking out old joints of roof tiles and M&L for flush pointing in cement mortar (1:3) mixed with SBR of FOSROC upto depth of 20mm complete including cutting / removing vegetation, complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc, including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories)

S&F PVC (SWR) pipes single socketed 110mm dia in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F PVC (SWR) bends of 110mm radius complete all as specified and directed.

M&L for preparation of old surfaces of wall/ceiling with the help of mechaniser sander of Make Berger Paints express painting sanding machine or equivalent make (having mechanical vaccum machine with bag for dust collection) to make surface smoth and even complete all as specified and directed.

M&L for applying waterproof cement based putty @ 1kg (undiluted) per sq mtr of average thickness 1mm, of Asian paints or its equivalent over the plastered/old painted wall after scrapping to prepare the surface even and smooth complete all as specified and directed. Step 1 : Mix the putty powder by adding 40-50% water and mix it with Asian Paints Trucare Putty mixer (Trucare Putty mixer with min 1400W power having mixer rod of industrial stell garde 45 with the mixing capacity of min 2.5kg putty per minute). Step 2 : Apply the first coat of the prepared mixer with the help of fully automatic airless spray machine of putty application of Asian Paints Trucare Graco Spray Machine (Model: EH 230DI) or equivalent having a DC electric motor of 3.3kW having flow speed of max 6 ltrs per minutes with a maximum pressure 230 bar having maximum tip size 0.041". Step 3 : Allow 6-8 hrs time to dry the putty surface. Step 4 : Sanding of the putty surface with Asian TruCare Wall Sander: L-01/H-01(having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc by skilled labour complete all as specified and as directed

M&L for one coat of acrylic waterbased interior grade primer @ 0.8 ltr(undiluted)/10 sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application of Asian Paints Trucare Graco or equivalant having an electric motor of min. 1 HP with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface for painting of subbsequent quotes.

M&L for applying two coats of smooth acrylic interior premium emulsion with rich matt finish having voc less than 50 grams per ltr complying leed criteria @ 1ltrs (undiluted)/10Sqm diluted with water in 2:1 ratio applied over priming coat with fully automatic airless spray machine of paint application of Asian Paints Trucare Garco or equivalent having an electric motor of minimum 1HP with a flow speed of minimum 1ltr per minute having a pressure of 3300psi. Allow 6-8hrs to dry the surface for painting of subsequent quotes.

M&L for applying two coats of oil bound distemper using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed. Note : - Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer.

Preparation of old surface after complete removal of existing treatment, applying 1mm thick wall care putty and making the surface smooth and applying two coats of oil bound distemper complete all as specified & directed. Note:- OBD shall be done with roller of required size instead of brush

M&L for preparation of old decorated plastered or unplastered surfaces of wall and applying two coats of oil bound distemper complete all as specified and directed NOTE:- OBD shall be done with roller of required size instead of brush

M&L for complete removal of existing treatment and preparing surfaces plastered or uplastered surface and applying 2 coats of plastic emulsion paint over 1mm thick wall care putty complete all as specified and directed Note:- Plastic emulsion paint shall be done with roller of required size instead of brush .

M&L two coats of colour wash on surface of wall including preparation of old plastered surface complete all as specified and directed

M&L two coats of oil bound distemper on surface of ceiling including preparation of old plastered surface complete all as specified and directed

M&L for preparation of old decorated external wall surface by sand paper of required sizes, filling in wall care putty in holes existing or created, again sand papering thus making surface smooth and one coat of cement base paint complete all as specified and directed.

M&L for preparation of old decorated external wall surface by sand paper of required sizes, filling in wall care putty in potholes existing or created, again sand papering thus making surface smooth and two coats of cement base paint complete all as specified and directed

M&L for preparation of old decorated external wall surface by sand paper of required sizes, filling in wall care putty in potholes existing or created, again sand papering thus making surface smooth and one coat of weather proofing exterior acrylic emulsion paint complete all as specified and directed

M&L for preparation of old decorated external wall surface by sand paper of required sizes, filling in wall care putty in potholes existing or created, again sand papering thus making surface smooth and two coats of weather proofing exterior acrylic emulsion paint complete all as specified and directed

M&L for one coat of synthetic enamel paint on old steel painted surfaces including preparation of surfaces of any description not otherwise described over 10 cm width or grith complete all as specified and directed

M&L for one coat of synthetic enamel paint on old wooden painted surfaces including preparation of surfaces of any description not otherwise described over 10 cm width or grith complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stone work and precast articles, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan on exceeding 6m mean radius, using old size brick, built in cement mortar 1:6, complete all as specified and directed.

All as per the description of srl item No 26 above but except bricks

M&L for brick work with sub-class "B' bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as directed and specified

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level), complete all as specified and directed.

M&L 40mm thick plain cement concrete 1:2:4 type B-1 ( using 20mm graded crushed stone aggregate) as in floors finished even and smooth using extra cement complete all as directed and specified

Supply only glass diving strips 3mm thick and 38mm width inserted in position, confirm to design, complete all as specified and directed.

M&L for plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 75mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified & directed. Note:- The unit rate include for use of form work (straight or curved).

Taking down chowkats or frames with shutters (without taking off shutters from the frames) of wooden/steel n.exc 1.5 sqm complete all as directed and specified

Taking down chowkats or frames with shutters (without taking off shutters from the frames) of wooden/steel exc 1.5 sqm but n.exc 4 sqm each complete all as directed and specified

Taking down shutters exc 1sqm but not exc 2 sqm each complete all as directed and specified

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc,complete drilled for fixing of steel sheeting in or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete, all as specified and directed

Taking down door shutters of any description exceeding 1 square metre and not exceeding 2 square metre each easing, and adjusting as required and re-fixing in same opening including renewal of screws complete all as specified and directed.

Dismantaling wrought iron or mild steel work of any description not otherwise provided for all as specified and direcred.

S&F aluminium powder coated three track window (two shutters glazed & one shutters wire gauge) with frame, glazed with 4mm thick tinted glass and wire guage with stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm including rubber bead joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc complete all as specified below:- (a) Frame (top & side) section shall of size 92.00mm x 31.75mm x 1.50mm. (Section No 21447) (b) Frame (bottom) section shall of size 92.00mm x 31.75mm x 1.50mm. (Section No 21446) (c) Top & side members of shutter section shall be of size 18.00mm x 40.00mm x 1.50mm. (Section No 21455) (d) Interlock Section of Shutter shall be of size 18.00mm x 40.00mm x 1.50mm. (Section No 21454) (e) Bottom Members of shutter section shall be of size 18.00mm x 40.00mm x 1.50mm. (Section No 20844), Note:- The unit rate quoted by contractor against this item is deemed to be included the cost of glass, wire mesh and all other connected accessories.

S&F factory made three track UPVC sliding windows white in colour or as approved made of extruded profiles with wall thickness of 2.3mm ((+/- 0.20mm) windows profiles with hollows section with multichamber. Frame size (88mmx52mm), Sliding sash (42mm x 67mm), sliding mesh sash (42mm x 57mm), sliding interlock(one vertical length in each shutter) 45.5mm x 28mm), glazing bead (24.5mm x 16mm) will be mitered cut and fusion welded at all coeners, including drilling of holes for fixing of hardware and drainage of wateretc, making arrangement for fixing of hardware, EPDM, gasket, 1.2+/-0.20mm thick galvanised steel frame (30mm x 28mm) 2 Nos sliding sash (30mm x 18mm), sliding mesh (26mm x 10mm), profile to be inserted in required profile frame will be fixed to the wall with 8mm x 100mm long fastener hardware, (Touch lock of zinc alloyed (white powder coated), steel roller system stainless steel wire 0.36mm nominal dia of wire and average width of aperture 1.40mm, aluminium grill and required accessories), Note - The unit rate quoted by contractor against this item is deemed to be included the cost of float glass thickness not less than 4.00mm and includes all another connected accessories complete all as specified and directed.

S&F casement windows with net & MS Grill single or multi shutter turn window are made out of UPVC multi-cavity frames sections of 60x60x2.5mm suitably reinforced and double mult-shutters division are made by using sash mullion having 50mm x 64mm x 2.5mm multi-cavity UPVC section, suitably reinforced with GI and shutters are made out of 50mm x 85mm x 2.5mm UPVC section, reinforced and welded in corners with EDPM gaskets provision for glass and for air tight at frames and outer side of shutter with single glaze window shutters using suitable glass bead with perfect hardware like hinges handles, stays etc complete. Mosquito mesh shutter is made out of UPC extruded section of 61mm x 27mm x 2mm with GI channel of 1.2mm thick, welded in corners. Stainless steel wire mesh (Mosquito net) to be fitted in shutter with proper required accessories like hinges, MS grill of 12mm round or square bar are inserted in main frameas guard bar & screwed by hidden screwing system with powder coating and filled the gap between wall and frame with weather proof silicon sealant over backer rod of required size and of approved quality etc complete all as specified and directed. Note:- The cost of float glass thickness not less than 4.00mm and stainless steel wire mesh 0.36mm dia of wire and average with of aparature 1.4mm is deemed to be included in quoted rates against this item and No extra payment will be made separately). Make/Manufactruer:- Fenesta/ Winkraft/ Yashpoly/ Duraplast/ Accura (Accucel).

M&L 40mm thick, plain framed, flush shutters with block board core and plywood face panel , commercial type both sides complete all as specified and directed.

S&F 35mm thick 2nd class HW glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc(with out sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauze etc size of members as specified in SSR part-I, section 8, clause 8.24(a)

S&F galvanised mild steel wire cloth cut to size, 0.56mm nominal dia wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staple complete all as specified.

S&F in repairs galvanised mild steel wire clothcut to size, 0.56mm nominal dia wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staple complete all as specified.

M&L for two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces including preparation of surfaces of any description not otherwise described over 10cm width or grith complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification and drawing.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frames shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or discription) from wooden frame or stone,concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F 3mm thick ordinary sheet glass and glazing with oil putty complete in squares not exc 0.50 Sqm each pane complete all as specified and as directed.

S&F in repairs for gypsum ceiling board for ceiling prepainted, perforated finish, 600mm x 600mm x 9mm to 9.5mm thick in size, of approved brand/make, laid over and including grid work of size 600mm x 600mm, made out of 0.5mm thick G.I. tee 32mm x 24mm for main, 25mm x 24mm for cross tee and 20mm x 20mm angle fixed on wall, powder coated finish on exposed faces of tee and angle. hung from ceiling using 2mm thick G.I. Suspension wires spaced at 1200mm on main runners including making niches for fans/light, including dismantling of wall ceiling and boards, (fibere pulp, insulation etc or insulation boards of anythickness including cover fitllets. all as specified and directed.

Taking down cement or cement plaster on brick walls/ceiling etc including raking out joints, hacking for key, scrubing down with water etc complete all as specified and directed.

M&L 15mm thick rendering on brick or concrete surface in cement mortar 1:4 mixed with water proofing compound, surface finished even and smooth without extra cement complete all as specified and as directed. Note:- Water proofing compound shall be measured and paid separately as supply only.

M&L for rendering 15mm thick in cement mortar 1:6 on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified and directed.

M&L 10mm thick rendering on concrete surface of ceiling in CM 1:3 finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in patches (not exc 3 Sqm each patch) in cement mortar 1:6 on other than fair face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement including taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 10mm thick cement plaster on brick or concrete surfaces, as in ceiling / facia / chajja etc. in cement mortar 1:3 finished even and smooth without using extra cement including taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Supply only integral water proofing compound.

M&L for preparing new plastered surfaces of walls and applying two coats of cement base paint, over a coat of alkali resistant priming paint complete all as specified

M&L for two coats of weather proofing exterior acrylic emulsion paint on new plastered surface of over a coat of primer case on any type and any height wall/ roof border, drops, fins, chajja / roof facia, column etc, including preparation of surfaces complete all as specified.

M&L for preparing new plastered surfaces of walls and applying two coats of oil bound distumper over 2mm thick wall care putty over over a coat of primer complete all as specified and directed

M&L for preparing new plastered surfaces of ceiling and applying two coats of oil bound distumper over 2mm thick wall care putty over over a coat of primer complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for non skid ceramic tiles colored tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floor etc set and jointed in neat cement slurry and pointed in colour cement laid over and including 15mm thick cement mortar screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for vitrified designer glazed coloured tiles 8-9mm thick (square/rectangular), area of each tile n. exc 0.36 sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and directed.

M&L glazed digital vitrified tiles (DVT) colour and shed as approved in vertical surface of size 450mm x 300mm x 7mm to 8mm thick with highlighter set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including rendering 10mm thick in CM 1:4 and finished rough, complete all as spd & directed.

M&L granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match including moulding chamfered edges and driling holes to the gas pipes with shade of granite including dismantling, complete all as directed.

M&L for 18mm thick PVC sheet for kitchen cabinet and cubboard consisting of carcass one side decorative lamination and other side balancing white fixed with approved adhesive and self tapping screws for kitchen cup board or wardrobe including dismantling of old boarding of any type complete all as specified and directed

M&L for 6mm thick PVC sheet for kitchen cabinet and cubboard consisting of carcass one side decorative lamination and other side balancing white fixed with approved adhesive and self tapping screws for kitchen cup board or wardrobe including dismantling of old boarding/sheet of any type complete all as specified and directed

S&F for 20mm wide & 1mm thick PVC edge beading pasted to edges of PVC furniture with suitable adhesive for kitchen cup board or wardrobe complete all as specified and directed

S&F stainless steel handle 100mm fancy type for cub board shutter complete all as specified and directed

S&F continuous (Piano) hinges, brass, 30mm width of flaps (when open).

S&F soft close heavy duty slow motion hinge steel nickel plated, 4 hole mounting plate, half overlay adjustment height/ depth fixed in repair completed all as specifed and directed.

S&F soft close heavy duty steel nickel plated telescopic drawer channel size 20 inch full extension load capacity 50 Kgs including fixing arrangement to drawer/ baskets etc completed all as specified and directed.

S&F in repairs soft close heavy duty steel nickel plated telescopic drawer channel size 20 inch full extension load capacity 50 Kgs including fixing arrangement to drawer/ baskets etc completed all as specified and directed.

S&F mild steel magnetic catches and striking plate of 50mm size for kitchen cup board or wardrobe fixed with screw including letting in and fixed completed all as specified and directed.

M&L mild steel conforming to Fe 410-0 or Fe 310-0 in framed work such as door chowkhat, grills, gratings, ladder, hinges, door frame, desert cooler stand etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings, coolar stand and similar work complete.

M&L applying two coats of synthetic enamel over a coat of red oxide primer paint on new steel surfaces of any description over 10cm width or girth including preparation of steel surfaces complete.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position of capacity exc 500 ltr and n.exc 1000 ltr. (Cleaning repairing, etc. measured separately)

S&F in repairs door bottom seal (with metal strip and nylon brush) complete all as specified

S&F in repairs fancy type stainless steel curtain rods powder coated polished 20mm dia including brackets and finale and connected items complete all as specified and directed.

S&F stainless steel butt hinges medium weight cold rolled 100mm long complete all as specified and directed.

S&F stainless steel tower bolt of extruded section and fixed lengtth of bolt 150mm complete all as specified and directed.

S&F 250mm long stainless steel sliding door bolt, complete all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, including sink coupling, 40mm waste fitting overall size 1040mm x 510mm bowl size 510mm x 405mm x 203mm complete all as specified and as directed.

S&F in repairs stainless steel peg set of six suitable size of length complete etc.

Demolition of cement concrete (unreinforced) of any description and in any position not specifically provided for complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in subase of floor, complete all as specified and directed.

M&L for sand filing under floors or in foundations including watering and consoldation complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block of colour Red/Yellow glossy type any shape and size, as approved by Engr-in-Charge confirming to IS 15658-2006 of 60mm thickness, M-35 Grade complete all as specified and directed.

M&L coloured chequered cement concrete tiles 30 cm x 30 cm x 25mm thick machine pressed set jointed and pointed with grey cement & pigments in floors over and including 15mm thick CM 1:6 including filling joints with white or colour cement as directed.

M&L for cement concrete 1:2:4 type B1 (20mm graded crushed stone aggregate in lintels upto 1.5 m clear span cills, holdfasts, steps, seismic and other similar bands, plinth courses, string courses lacing courses parapets and railings upto 60cm in height copings, kneelers apex stones, bed plates, kerb not provided for water troughs and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

S&F in repairs of 20mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including complete all as specified and directed. Note:-(i) Rate including hanging arrangement for fixing of CPVC pipes in shaft of Building (up to G+8 Storey) (ii)The rate also includes the cost of the all special fittings Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor, Unions, Ball valves and tank adaptor which may be required

M/S GR construction compony (BID ID -3067946)

V M CONSTRUCTION (BID ID -3065720)