ADDN / ALTN / IMPROVENMENT AND PROVN OF BASIC AMENITIES IN BILLETS AND MESSES AT AF STN BORGAD

Amount

Taking down chowkhats or frame, n.exc 1.5 sqm each with shutters (without taking off shutter from the frame) all as directed.

Taking down chowkhats or frames with shutter (without taking off shutter from the frame) exc 1.50 & n.exc. 4 sqm in each complete all as directed.

Taking down with shutters of any description but exc 2 Sqm

Dismantling boarding, any description, fixed in any position with nails as directed

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc complete all as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for, including reinforcement cut as required to facilitate demolition of concrete, complete all as specified and directed.

M&L for reinforced cement concrete type B1 (1;2;4) nominal mix using 20 mm graded broken stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, shelves and the like.

M&L for Formwork to soffits of suspended slabs such as roof slabs,floor slabs,landings and similar work n exc 200 mm thick

S&F mild steel TMT bar of 10 mm dia and over cut to length bent to shape required including cranking and binding with mild steel annealed wire not less than 0.9 mm dia.

M&L for demolition of concrete(unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing debris to location outside defence land complete all as directed.

Taking down cement plaster any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete.

Dismantling of stone slab and tiles of any description or thickness in floors or walls, aprons etc tiles laid, bedded and pointed in any mortar complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises completed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces with cement plaster of 1 :4 all as specified & directed

Material and labour for preparation of new plastered surfaces of walls and applying two coats of white wash complete all as specified and as directed.

S&F 25 mm thick insulated PVC wall lining consisting of PVC insulated panel with single side prelam PVC sheet used instead of plain colour sheet duly fitted into the wall incl PVC stirps per specifications & drawing

S&F horizontal level suspended celing comprising of Armstrong GI clip-in micro perforated 600 x 600 mm (nominal size) tiles of 120 mm galvanised steel as per IS277 (2003) suitable for architectural finishes in 0.5mm thickness as per IS:513 (1994) in global white colour concealed suspension system having a bevelled edge of 3x3 mm and height of 33mm on one side and 18mm on other side. Tile shall have perforated of hole diameter 2.5mm and open area 16% with linear and diagonal pitch of 5.5 mm and 7.7mm respectively along with a border of 10 mm.The tile shall be electrostaticalkly polyster powder coated using RoHS compliant powder having coating thickness ranging from 60-80 microns. Back side of the tile shall have soundtex fleece hot pressed mechanically for uniform bonding to achieve NRC up to 0.7 all as per manufactures instruction , complete all as specified and as directed by Engineer-in-charge. Note : if electrical cables are running at site and required to be relocated electric fittings on walls are required to be shifted including refixing of fan/ lights and other light accessory including making.

M&L for 100 mm thick PCC type D2 1:4:8 (using 40mm graded aggregate) as in Sub base of flooring finished the surface rough complete all as specified and directed.

M & L machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed in neat cement slurry with pigment to match the shade of slab incl rubbing & polishing complete all as specified and as directed.

Material and labour for machine cut kota stone slab flooring 20-25mm thick as in floors of landing/passages/raiser & treads of stair case steps etc, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing, edges rounded with three line grooves in each tread of steps, laid over and including cement screed base 15mm thick in CM 1:6, complete all as specified and directed. Note: Kota stone to be used for treads and risers of stair case shall be in single piece.

Material and labour for 25mm thick cement concrete 1:2:4, type B0 using 12.5mm graded stone aggregate as in bedding layer of floor, finished the surface even and rough complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (Square/Rectangular) area of each tiles exc 0.11 sqm but n exc 0.18 sqm as in floors etc., laid over and including 15 mm thick screed bed of cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

All as per item No 23 above but in skirting over 10 mm thick plaster in cement mortar 1:4 including necessary cutting of tiles as required size all as specified and as directed.

M&L Glazed ceramic coloured tiles in vertical surface 450x300 x 7-8 mm thick joint free set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in Cement Mortar 1:4 complete all as specified and directed.

S/F stainless steel towel rack 60 cm long and 20 mm dia and 30 cm in width all as specified & directed

S&F in repairs Vitreous China wash basin (WHB), white, flat back, size 450x300mm excluding taps and plug but including Angle Iron brackets, 32 mm dia CP waste coupling, 32 mm bore PVC Waste Pipe complete all as specified and directed.

S&F in repairs vitreous china half stall urinal (White) with grating & union for discharge pipe including providing and fixing CP pipe for spreader and CP push cock etc complete all as specified & as directed.

Supply and fixing in repairs CP brass shower rose of size 125 mm saquare/circular as approved swivel type with CP extension rod 15mm dia and 200mm long suitable for 15mm bore pipe .Complete all as specified and directed by Engineer-in-charge.

S&F fancy type soap dish stainless steel as appoved by GE complete all as specified and as directed by engineer-in-charge.

S&F in Repair bib tap with flange of bore size 15mm, cast copper alloy, chromium plated, fancy type, with crutch or butter fly handle screwed down , screwed for iron pipe or for brass ferrule Complete all as specified and as directed by Engineer-In-Charge.

S&F in repair health faucet with one metre long flexible tube and wall hook chromium plated, screwed down for iron pipe complete all as specified and directed by engr in charge

Supply and fixed in repairs PVC connection 15mm size with PTMT nuts, of length 600mm complete all as specified and as directed.

S&F in Repair Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm and equivilent in (Make Nirali,Neelkamal, Bajaj) .complete all as specified and as directed by Engineer-In-Charge.

S&F in repair Brass Chromium plated Tubular Towel rail, 20mm dia, D type, 60 cm long between flanges fixed to wall complete all as specified and directed.

S & F in repairs, vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm, white with integral foot rest and 'P' or 'S' trap, including provision of Cement concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing surface all as specified and directed.

Supply and fix in repair 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve, float, handle , PVC Flush Pipe and brackets including taking down old cistern all as specified and as directed.

S&F Cast copper alloy CP angle valve type stop cock suitable for 15 mm bore pipe screwed at both ends or high pressure with Capstan head,Complete all as specified and as directed by Engineer-In-Charge.

S&F 100mm dia cast iron Floor Trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as directed.

Supply and fix Low density polyethylene pipes (LDPE) of pressure rating 6 kg/ cm2 of 40 mm dia bore for wash hand basin complete all as specified and directed.

Supply and fixed to wall, Cast iron (Spun) soil, waste and vent pipes of 100mm bore, in any length with or without ears, with cement joints, inclding taking down existing unserviceable CI pipe with fittings complete all as specified and directed.

Supply and fix Cast iron Bend (any radius) 100mm bore of pipe diminishing pieces or tapers (larger bore measured), with oval access door, complete all as specified and directed.

S&F in repairs 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered "Hot or Cold" with long screwed shanks and fly nuts, screwed for iron pipe etc complete as specified and directed.

S&F in repairs 15mm bore, stop valve/angle valve, chromium plated, fancy type cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store bore of pipe 15mm complete all as directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store bore of pipe 20mm complete all as directed.

Supply and fix 15mm dia steel water tubing medium grade galvanised with all fittings and fixed to wall and ceiling or laid in floor complete all as specified and as directed.

Supply and fix 20mm dia steel water tubing medium grade galvanised with all fittings and fixed to wall and ceiling or laid in floor complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good , cutting not exc 10cm girth complete all as directed.

Cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings or cutting out defective brick work for under pinning, including providing fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core etc to store and rubbish not exc. 50 ms

Material and labour for Aluminum powder coated sliding window with aluminium powder coated three track frame of size 92mm x 32 mm & 1.3 mm thick with 3 Nos sliding shutters of powder coated aluminum section (top rail bottom rail and style of size 40mm x 18mm & 1.3mm thick) screwed to walls/floor including provn of tinted sheet glass panels of 4mm thick fitted in pannels (2 Nos) and one shutter with stainless steel wire cloth 0.36 mm nominal dia and width of aperture 1.40mm with and including necessary locking device, jointing cleats, glazing clips, rubber packing beading , aluminum bidding and screws etc. complete all as specified and as directed by Engineer-in-Charge..

M/L for powder coated Aluminium ventilators louvers pattern with aluminium frame of minimum size 38.0mm x 75 mm x1.6 mm thick with other accessories as per standard sections necessary clips , frosted glass , wire mesh ,handels for up and down suitable fo wc and bath ventilation completed and as directed by Engr in charge

M&L framed work such as grills grating etc with end of bars shoulderd and/or riveted . Welded or forged into spikes. Framedguard bars iron doors . Ladders framed balusters , walk ways . Railings , frame work of of water tanks and similar work conforming to Fe 410.

S & F in repairs curtain rod of metalic 25 mm dia Harrison rails, mild steel, chromium plated including long projected bracket of heavy section both side fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified as directed by Engineer -in -charge

Supply and Fix Fiber glass Reinforced plastic FRP door frame of size 90mmx45mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness completeall as specified and as directed.

S&F 30 mm thick fiberglass reinforced Plastic (FRP) flush door shutter in different plain & wood finish made with fire retardant grade unsaturated polyester resin as per specification and drawing Complete all as specified and as directed.

S & F 30 mm thick flush shutter solid core construction, with block board core and plywood face panels, commercial type on both faces complete as specified and directed.

S & F 35 mm thick second class hardwood glazed & skeleton shutters open rebated & prepared to receive glass, gauge etc (without sash bars) fitted with cut and mitred securing beads for securing glass etc. complete as specified and directed size of members of sutters as specified in SSR Part I section 8 clause 8.24 (a) complete all specified and directed.

Supply and fix galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or wooden beading patti compete complete all as specified and directed.

Supply and fix butt hinges 100 mm size, medium weight cold rolled mild steel compete all as specified as directed

S&F 100 mm long stainless steel grade 304 mortice key lock set 4 lever complete all specified and directed

Supply and fix 150 mm long aluminium anodised barrel tower bolts of extruded section, ISI marked compete all as specified as directed

Supply and fix 150 mm size extruded aluminium alloy handles, fabricated type, anodised, ISI marked compete all as specified as directed

Supply and fix Mild steel Chromium plated sliding door bolts 300 mm long, plate type with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

S/F SS door stopper fancy type 125 mm long fixed to door with CP screws etc completed and as directed

M&L for Repairs to sunken floor slab with the following specification :- (a) Roughening surface of old concrete floor and wall bypicking,sweeping clean and washing down with water to remove dust etc. (b) PCC 1:2:4 type B-O using 12.5mm graded stone aggregate averaging 50mm thick as in sunken floor with proper slope towards GI spout. (c) providing 15mm thick cement plaster in cement mortar 1.3 mixed with water proofing compound @ 3% by weight of cement over bottom and vertical surfaces finishing the surface even and smooth without using extra cement. (D) Damp proof course on horizontal surfaces with scrapping and properly cleaning the surfaces to remove loose particles & applying one cot of self priming (33% dilution) and to coats of undiluted material with @ 10.67 ltr per 10 sqm smart care Damp proof of asian paint for water proofing and Damp proof course on vertical surfaces scrapping and properly cleaning the surface to remoov loose particle and applying one coat of self priming (33% dilution) and one coats of undiluded material with @ 4.85 ltr per 10 sqm smart care Damp proof for water proofing (E) Brick bats filling under sunken floor. (F) PCC 1:3:6, type C-2 using 20mm graded stone agregate 75mm thick,over brick filling as in subbase to recieve tiles. Note:- (i) Water proofing compound shall be measured and paid under relevent items. (ii) For payment purpose only floor area shall be measured. (III) Contractor will submit gurantee for leakage/ seepage for 5 year after completion of work.

M & L for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes set in cement plaster of 1:4

M & L for machine cut cudappah stone slab 20-25 mm thick over cement screed base, laid and jointed in grey cement slurry mixed with pigment to match the shade of the slab incl rubbing & polishing complete

M & L for 16-18 mm thick Granite black colour, work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, shelves and like jointed over and including 10mm thick cement mortar 1:4 screed and pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite, incuding grinding, moulding and polishing to exposed edges complete all as specified and directed.

M&L for drilling holes for pipes etc in cadappa/granite including RCC slab n exc 25mm dia and n exc 150mm depth

M&L 18/19mm thick Block boards, grade 1 quality, exterior grade, commercial type, fixed with screws to timber frame work as in cub borads, kitchen cabinet shutter, shelves etc, complete all as specified and directed.

S&F 0.90 mm thick decorative laminate type1 of smooth and glossy surface finish colour and pattern as approved, fixed with approved adhesive as per manufacturer instruction etc complete all as specified and directed.

Supply and fix 150 mm size mild steel pressed handles ,oval type stove enamelled black compete all as specified as directed

M&L for preparing new steel surfaces of any description width or girth exc 10 cm applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome all as specified and directed.

M&L for preparing old steel surfaces of any description width or girth exc 10 cm applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome all as specified and directed.

M & L two coats of synthetic enamel paint over one coat of pink primer on wood or wooden based surface exc. 10 cm width or girth including preparation of new or previously untreated surfaces complete all as specified and directed.

M & L for preparing old wooden surfaces & two coats of synthetic enamel paint over one coat of pink primer on wood or wooden based surface exc. 10 cm width or girth complete all as specified and directed.

Material and labour for preparation of old plastered surfaces of ceiling and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

M &L complete removed existing treatment on old plastered surface of wall and applying 1-3 mm thick wall care putty in two layers to achive smooth surface of walls applying two coats of plastic emulsion over a coat of primer for internal walls complete all as directed.

M&L for preparation of old plastered or unplastered surfaces of walls by brooming down or steel wire brushing.scrapping down smoke soot.moulds.moss and efflorescent salts,trading oil and greasy spots, l etc and applying two coat of exterior acrylic emulsion paint (Weather coat) white/coloured on walls with and including provision of scaffolding , ladders, cradles etc if required for the treatment to external surfaces of building with required safety measures etc complete all as specified and directed by Engineer in charge

Taking down existing copper/aluminum point wiring (light/ fan/ socket or power points) complete including (fittings such as switches, ceiling roses, pendents, regulators, sockets, etc including wooden battens /casing /capping and conduit etc and making good disturbed surface of walls, ceilings and floors etc. complete all as specified & as directed by Engineer-in-Charge.

Taking down old /unsv sub main wiring

Taking down old /unsv DBs , including MCBs etc

M & L for Point wiring with 1.5 Sqmm (nominal area) PVC( FRLS) insulated sheathed copper stranded conductor cable run in and including concealed in wall/floor PVC conduit not less than 20 mm medium grade as per IS with all fittings such as bends, tee,junction boxes,etc of suitable size including 1.5 Sqmm PVC(FRLS) insulated copper earth continuity conductor connected to common earth dolly and including MS/GI sunken boxes with modular inner & surface plate suitable for housing modular switches, sockets,fan regulators etc for one light/fan/call bell point controlled by one 1- way switch complete all as specified and as directed by Engr -in -Charge. Note:- Cutting & making good of chasis in the wall/Roof/Floor is deemed to be inclued in the quoted rates.

All as per item no 86 but for One 5 Amps socket point on same/below board with other switches.

All as per item no 86 but for One 5amps switch socket point independent.

M & L for Point wiring with 2.5 Sqmm (nominal area) PVC( FRLS) insulated sheathed copper stranded conductor cable run in and including concealed in wall/floor PVC conduit not less than 20 mm medium grade as per IS with all fittings such as bends, tee,junction boxes,etc of suitable size including 2.5 Sqmm PVC(FRLS) insulated copper earth continuity conductor connected to common earth dolly and including MS/GI sunken boxes with modular inner & surface plate suitable for housing modular switches, sockets,fan regulators etc Note:- Cutting & making good of chasis in the wall/Roof/Floor is deemed to be inclued in the quoted rates.

Supplying and fixing Modular switch , one way, 16 amps, one Module of Make:- Ancher Roma/Legrand/ Crabetree.

Supplying and fixing Modular socket 16 amps-6 pin multipin, 2 Module of Make:- Ancher Roma/Legrand/ Crabetree.

Modular switch one way 6 Amp,1 Module , Make Legrand / Anchor Roma/Crabetree .

Supplying and fixing Modular socket, 6 amps-2/3 pin combined, 2 Module, Make Legrand / Anchor Roma/Crabetree .

Supply & Fix Modular bell push 6 Amp,1 Module , Make Anchor/ Roma/Legrand.

Supply & Fix Modular Fan regulator electronic step type 230 V 2 Module. Make :Legrand/Anchor/Roma.

Supply & Ding Dong AC 230 Volts single pole. Make : Anchor/Press Fit

Supply & Fix Ceiling rose surface type, PVC/Polycarbonate isolated body size 50x28 mm two to three terminals. Make : Anchor/Leader.

Supply and fix in repair MCB SP 6 to 32 Amps 240 volts 10 KA C series. MCB with separate short circuit indication type Make Legrand Cat. Nos 408595 Or equivalent Make :Siemens/L&T, Complete all as specified & as directed by Engineer-In-Charge

Supply and fix in repair MCB SPN 6 to 32 Amps 240 volts 10 KA. Make Legrand Cat. Nos 408617 Or equivalent Make :Siemens/L&T, Complete all as specified & as directed by Engineer-In-Charge

Supply and fix in repair Sheet metal enclosure for DB’s SPN, with 200 amps rated bus bar ,4 way ,240 volts double door. Make : Standard/HPL/Legrand.,Complete all as specified & as directed by Engineer-In-Charge.

Supply and fix in repair Sheet metal enclosure for DB’s SPN, with 200 amps rated bus bar ,8 way ,240 volts double door. Make : Standard/HPL/Legrand.,Complete all as specified & as directed by Engineer-In-Charge.

Supply and fix sheet metal distribution board 415volt,Vertical TPN 4 Way with provision for DHx100 series MCCB of legrand make as incomer and SP/TP MCBs as outgoing as per IS including compact insulated bus bar and rounded neutral bar, door earthing complete double door surface/reccess mounting IP-43 protection of L&T Cat No DBVTL004GD or equivalent in Legrand/Siemens.,Complete all as specified & as directed by Engineer-In-Charge.

S&F MCCB TP ,Thermal magnatic with enclouser , 415 Volts,50 HZ, 30 KA, 100 Amps DU-100H Cat No CM9789400k2 of L&T or equivalent Model of Legrand, Siemens.,Complete all as specified & as directed by Engineer-In-Charge.

M&L wiring for circuit/ sub main wiring of 2x4.00 Sqmm+1x4.00 Sqmm earth wire, alongwith earth wire PVC (FRLS) insulated copper conductor, single core, 1100 v grade cable in surface/concealed as required in and including in PVC conduit 20mm dia medium grade complete all as directed by Engr -in- Charge. Note:- Cutting & making good of chasis in the wall/Roof/Floor is deemed to be inclued in the quoted rates.

M&L wiring for circuit/ sub main wiring of 2x6.00 Sqmm+1x6.00 Sqmm earth wire, alongwith earth wire PVC (FRLS) insulated copper conductor, single core, 1100 v grade cable in surface/concealed as required in and including in PVC conduit 20mm dia medium grade complete all as directed by Engr -in- Charge. Note:- Cutting & making good of chasis in the wall/Roof/Floor is deemed to be inclued in the quoted rates.

Disconnect and insulate electric supply wire and taking down carefully ceilling fan 1200mm/exhaust fan 300mm of any make dismantlling blades, and deposited to AGE E/M store yard for reused. complete all as specified & as directed by Engineer-in-Charge

Hanging only old ceilling fan any sweep/ capacity including servicing of fan ,cleaning of all parts greasing oiling of bushes and bearing reassembling and testing for smooth functioning for celling fan/exhaust fan, including replacement of 0.5 sqmm 3 core copper conductor flexible cable connected from celling rose to fan complete all as specified & as directed by Engineer-in-Charge

Supply & Fixing Exhaust fan 300 mm sweep, minimum 1350 RPM , Metal body and blades , frame and louvers made of iron/ aluminium (As Sample approved ) of matching colour with exhaust fan of suitable size , operated on 230/240V AC Single phase electric supply complete duly grauted bolts in the wall fixed with nuts, bolt and washers including making suitable size hole in the existing wall and making good the plastering by matching colour with existing colour to the disturbed surface of wall complete , including connecting with 3 core stranded copper conductor cable cordas as per manufacture recommendation from ceiling rose to exhaust fan connector including writting MES No. on Exhaust fan white synthetic enamelled paint complete all as per specified and directed by Engr-in- Charge . Make- Havells Cat Pt No Ventil Air DB 300 mm 4 blade or equvalent in , Crompton Transair , Usha Turbo DBB.

Supply, installation, commissioning and testing of storage type electric water heater of capacity 25 Ltrs, AC ,240 Volt, 50 Hz, 5 star rating vertical/ Horizental type duly fixed to existingposition where directed including suitable mounting bolts, nuts and washer duly grouted including necessary accessories such as saftey valve, thermostste, NRV, inlet / out water connection piece etc incl writing MES No, on Geyser with white synthetic enamelled paint , all as specified and as directed by Engr-in-Charge. Make Havells Cat Pt No- Monza DX GHWAMGTWH025 or equvalent in Jaguar Cat Pt -Elena digital ,Usha Cat Pt - Aquagenia

Fixing only serviceable tube flight fitting or any type of fittings complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair decorative ultra slim square profile linear Light Linea lighting fixture extruded polycarbonate, environmental friendly, energy efficient ready to use pack 20 W LED 6000K, complete all as specified and directed by Engineer-in-Charge. MAKE : Crompton, Model No. LDLL20-CDL or equivalent in Bajaj/ HAVELLS.

Supply and fix in repair decorative ultra slim square profile linear Light Linea lighting fixture extruded polycarbonate, environmental friendly, energy efficient ready to use pack 10 W LED 6000K, complete all as specified and directed by Engineer-in-Charge. MAKE : Crompton, Model No. LDLL10-CDL or equivalent in Bajaj/ HAVELLS.

Supply and fix in repair decorative ultra slim square profile linear Light Linea lighting fixture extruded polycarbonate, environmental friendly, energy efficient ready to use pack 5 W LED 6000K, complete all as specified and directed by Engineer-in-Charge. MAKE : Crompton, Model No. LDLL10-CDL or equivalent in Bajaj/ HAVELLS.

Supply and fix in repair 36W LED 5700K Ultra modern recess mounting luminare suitable for armstrong/ grid/ POP ceiling complete with separate electronic driver & high brightness SMD LEDs, complete with connecting accesseries & Driver duly pre-wired and connecting up with 0.5 Sqmm 3 core flexible Copper cable cord from fitting, complete all as specified and directed by Engineer-in-charge. MAKE : CROMPTON , Model No. LCTLRNE-36-FO-CDL or equivalent in Bajaj/HAVELLS.

M/s.TIRUPATI BUILDERS

SHREE SAMARTH SERVICES