SPECIAL REPAIR TO 4 X TOILETS OF OR OTM BLOCK AND SEPTIC TANK NO. 2 AT KLP AND CERTAIN MISC EM WORKS AT MIL STN JAISALMER

Amount

Taking down cement or cement lime plaster from stone walls etc including racking out joints hacking for key scrubbing down with water etc & removing rubbish out side MD land all as directed.

Dismantling floor, hearth or wall tiling including cement mortar, removeing and rubbish off the premises.

Demolition of stone/ boulder masonry and built in cement mortar including all quoins arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m all as specified & directed by Engineer-in-charge.

Demolition of cement concrete unreinforced in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m all as specified & directed.

M&L for glazed ceramic drak shade tiles in vertical surfaces 350x250x7mm or 450x350x7mm set and jointed in neat cement slurry and pointed in coloured cement incl boarder tiles with 10mm thick rendering as in backing coat of CM 1:6 all as directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exc 0.06sqm but not exc 0.11sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement over 15mm thick screed bed in CM 1:6 all as specified.

M&L for rendering 10 mm thick on concrete surface in cement mortar 1:6 & finished the surface even & fair without using extra cement all as specified.

M&L for rendering 15 mm thick on stone masonry surfaces or surfaces other than fair faces of brick work or on one side of lathing in cement mortar 1:6 & finished the surface even & fair without using extra cement all as specified.

M&L for rendering 10 mm thick on concrete surface in cement mortar 1:6 & finished the surface even & fair without using extra cement all as specified.

M&L Preparation of plastered surfaces and applying three coats of white wash on wall surfaces all as directed

M&L preparing new plastered surfaces of wall and applying two coats cement base paint over a coat of primer on wall.

M&L for Preparation of old plastered surfaces and applying one coat of white wash on walls all as directed

M&L Preparation of plastered surfaces and applying three coats of white wash on ceiling surfaces all as directed

S&F in repair flush pipe of polyethylene of low or high density of PVC 32mm dia for low level flushing cistern / WHB.

S&F in repair vitreous china squatting pan orissa pattern complete of size 580 x 440 mm white with intagral foot rest and making good to the floor complete fixed in repairs. (Make:- Hindware Cat part No - 20042)

S&F in repair PVC low level white flushing cistern syphonic action type 10 ltrs capacity incl flush pipe 32 mm dia incl PVC connection 450 mm long and complete fixed in repairs.(Make:-Cera Cat part No B1010102, Hindware (Sleek) , Commander(Water Bird)

S&Fin repair wash hand basin vitereous china flat back size 550 x 400 mm white incl CP waste coupling waste pipe brackets complete fixed in repairs.

Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frames)

S&F 150 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete.

S&F 150 mm long Aluminium handles, cast type, anodised complete.

S&F Butt hinges 100 mm including necessary welding if required all as directed by Engr- in -Charge.

S & F MS Pressed handle 150mm size oval type stove enameled black

S & F mild steel tower bolts 150 mm long stove enameled black with bright bolt complete all as specified and directed.

S & F mild steel sliding bolt 300 mm long plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fix complete all as specified and as directed

S & F 35 mm thick factory made second class hard wood, kiln seasoned and chemically pressure treated plain framed, panelled shutter (Two panel) with lock rail and panel of 9 mm BWP Commercial ply or 12 mm veneered particle board with commercial face veneers on both faces or 10 mm bison panel all as directed by Engineer-in-Charge

S & F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MSD square tube etc all as specified and as directed.

S&F factory made solid PVC moulded door shutter 28 to 30 mm thick (style) with 2, 4, 6 raised panel design with 2 mm moulded PVC sheet on the front face and2 mm moulded PVC sheet on back face supply and fixing in the frame at site as per specification with particle board core complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame exc 1.5 sqm including punching or drilling out old glazing pins/ springs clips and providing and fixing new ones.

S & F 4 mm thick plain glass and glazing with oil putty in squares not exceeding 0.5 Sq. M in each pane.

S&F GI tubing (ISI) marked) medium grade with all fitting including taking down old pipe and fixed complete to wall ceiling or laid in floors of following sized :-

(a) 15 mm bore

(b) 20 mm bore

Taking down old steel tubing including cleaning and connections in new or old position (Wall, ceiling, floors etc) of the following size :-

(a) 15 mm bore

(b) 20 mm bore

S&F bib tap 15 mm dia cast copper alongwith crutch or butterfly handle screwed down CP fancy type 15 mm dia fixed in repairs.

S & F for Bib cock 15 mm dia cast copper alloy with butter fly handle, screwed down, screwed one ends for pipe of 15 mm dia complete all as specified and directed.

S&F stop valve 15 mm bore CP fancy type screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union and fixed in repairs.

S & F for Stop valve 15 mm dia cast copper alloy with butter fly handle, screwed down, screwed both ends for pipe of 15 mm dia complete all as specified and directed.

S & F in reapir 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors fixed to walls all as directed by Engineer-in-Charge.

M&L Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer.

M&L Preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer.

M&L Preparation of old wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coats of Synthetic enamel paint

S&F Precast Reinforced Cement concrete Type B0 (Using 12.5 mm graded stone aggregate) in 35 mm thick Jallies or louvers including all mouldings complete and set in Cement Mortar 1:4

Dismantling water tanks and removing to store (exc500 and not exc 1000 ltr cap)

S & F 1000 litres capacity Three Layers White colour Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including taking down old PVC tank

S&F of 25mm dia bore of pipe Ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed

M&L for granite slab of any type of 18mm thick machine cut bedded and jointed with grey cememt slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and plishing complete all as specified and directed.

S & F 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe.

S&F in repair Vitreous China Urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)(Make:-Cera Cat No S4020102 , Hindware Cat part No - 60002)

S & F Steel windows with side hung shutters including projecting type hinge with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded

S & F in repairs Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union

S & F tubular aluminium anodised 60 cm long towel rail 20mm dia D type complete fixed with screws etc.

S & F 3.0 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares n.exc 0.5 Sq. M in each pane

PCC 100 mm thick in type B-2,1:2:4 using 40mm graded stone aggregate as in sub base complete all as specified and as directed.

Precast cement concrete 1:3:6 type C1 (Using 20 mm graded granite stone aggregate) block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6

PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in coping etc and like, including weathering, slightly rounded or chamfered angles and throating as directed with and includings necessary fro work complete.

Rendering 15mm thick plaster on block masonry surfaces in CM (1:4) finished even and smooth without using extra cement.

M&L for jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted, set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete complete all as specified and as directed by the Engineer-in-Charge

M&L for PCC 1:2:4 type BO using 12.5 mm graded stone aggregate for levelling course for consolidated thickness shall be varied from 25 to 85 mm as per the requirements all as directed by Engr-in-Charge.

M&L rendering 15mm thick in 1:4 cement plaster on roof surface by using WPC Compund and surface finished even and smooth complete all as specified and directed.

Supply only integral water proofing compound.(ISI Marked)

Excavation over areas not exceeding 1.5m deep and getting out soft/ disintegrated rock all as specified & directed by Engineer-in-Charge.

Excavation over area exceeding 1.5m deep but not exceeding 3.00m deep and getting out soft/ disintegrated rock all as specified & directed by Engineer-in-charge.

M&L for plain cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete all as specified & directed by Engineer-in-charge.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) all as specified & directed.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses all as specified & directed.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soft/ disintegrated rock all as specified & directed by Engineer-in-Charge.

Removing excavated soft/disintegrated rock to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as directed & specified.

M&L for 40mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in base for screed all as specified & directed by Engineer-in-charge.

M&L for screed bed or bedding layer of 15mm thick in CM (1:4) complete all as specified & directed by Engineer-in-charge.

S&F, anodised aluminium frame & shutter for door, window and ventilator including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, hinges, tower bolt, etc complete all as specified & directed by Engineer-in-charge. (Note :- Floor door spring & sheet glass shall be measured and paid seperately).

S&F second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified & directed by Engineer-in-charge.

S&F 35mm thick, fancy type Plain, framed, moulded on solid (for each side) panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats.

S&F, 300mm long brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as directed by Engineer-in-charge.

S&F 125mm size butt hinges extruded brass, with mild steel hinge pin, bright polished type B-11 complete all as specified & directed by Engineer-in-charge.

S&F 100 mm size 4 Levers, fancy type, brassl mortice Lock, vertical type complete all as specified & directed by Engineer-in-charge.

S&F 150mm long floor door stopper of brass body and tongue with hard drawn steel spring complete all as specified & directed by Engineer-in-charge.

S&F, 150 mm long, brass handles, cast type, polished bright complete all as directed by Engineer-in-charge.

M&L for two coat of french polishing on wooden surfaces of any description width or girth including cleaning and preparing the surfaces including a coat of wood filler on new works all as specified & directed by Engineer-in-charge.

S&F Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F aluminium (Die cast) door closer hydraulically regulated designation No. 3, universal type, suitable for door shutter of 851 mm to 1000mm in width and of weight between 61 to 80 Kg complete all as specified & directed by Engineer-in-charge.

S&F, 5.5mm thick, sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each panes complete all as specified & directed by Engineer-in-charge.

M&L for 50 mm bore mild steel galvanized water tubing, medium grade with all fittings and accessories complete fixed to walls and celling or laid in floors complete all as specified & directed by Engineer-in-charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in any type of soil all as specified & directed by Engineer-in-Charge

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc not exceeding 10 Sqm on plan and getting out in soft/ disintegrated rock all as specified & directed by Engineer-in-Charge

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc not exceeding 10 Sqm on plan and getting out in hard rock all as specified & directed by Engineer-in-Charge

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil all as specified & directed by Engineer-in-Charge.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with hard rock all as specified & directed by Engineer-in-Charge.

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as directed.

Removing excavated hard rock to distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as directed by Engineer-in-Charge.

M & L for cutting existing GI tubing for alteration or additions of sizes including screwing existing GI tubing for tapping & making new connections etc of size 50 mm bore complete all as specified and directed by Engineer-in-charge.

S&F gun metel, globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed for the of size 50 mm bore with ISI marked and as per IS 14846 all as specified and directed by the Engineer-in-Charge.

Taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit including removal of batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes all as specified.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including MCBs any type and capacity making good the disturbed surfaces to match with the existing finishes all as specified.

M & L for Point wiring using colour coding as per IS with 1.5 Sq mm multistranded copper conductor single core FRLS PVC insulated unsheathed 1100 Volts, ISI-694 marked drawn through and including heavy duty ISI marked PVC concealed conduit alongwith its accessories of suitable size, with GI sunken boxes of 1.2 mm thick, 60 mm depth of suitable size including fixing/ grouting sunken as per site requirement and making good to match with existing finishes including provision of cover with white colour hylum sheet of 3.6 mm thickness switches/ sockets/ regulators etc including running up of 1.5 Sq mm copper conductor FRLS, PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly all as specified for the following :

(a) One light point controlled by one, one way switch

(b) One three pin 5 Amps socket outlet point controlled by one No one way switch on same board

(c) One three pin 5 Amps socket outlet point controlled by one No one way switch on independant board

All as per Item No. 93.00 above but with stranded copper conductor 2.5 Sq. mm (nominal area), single core, PVC insulated and unsheathed multistranded FRLS cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated multistranded FRLS copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly.

All as per Item No. 93.00 above but with stranded copper conductor 4.0 Sq. mm (nominal area), single core, PVC insulated and unsheathed multistranded FRLS cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated multistranded FRLS copper conductor 4.0 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly.

S&F for Switch piano flush type single pole one way, and 6 amp complete ISI mark complete all as specified.

S&F for Socket outlet multipurpose having provision for 2 in 1, 3 pin 5 amp piano flush type complete all as specified

S & F for Switch piano flush type single pole one way, and 15 amp complete ISI marked complete all as specified.

S&F for socket outlet 2 in 1, 2/3 pin 5 Amps and 15 Amps flush type complete all as specified.

S & F for celling rose 2/3 terminals, PVC/ polycarbonate, isolated body ISI marked complete all as specified.

S & F for MCB DB SPN 4 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 230 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed .

S & F for MCB SPN double pole rated capacity 40 amps, 230 volts breaking capacity 10 KA complete all as specified and as directed.

S & F for MCB Single pole rated capacity 6 to 32 amps, 240 V breaking capacity 10 KA complete all as specified and as directed.

M & L for submain wiring with approved colour code/as per IS (Red,black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 6.00 Sqmm (FRLS) in PVC casing caping including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 4.00 Sqmm (FRLS) of continous earth wire green in colour complete including taking down old unserviceble sub main wiring all as specified and directed by Engr-In-Charge.(Note :- Two runsof 6.00 Sqmm cable & one run of 6.00 Sqmm cable one run of PVC casing caping shall be paid as one unit length)

S & F for LED tube light fitting 20 Watt 4 Feet or 1183 MM in lenth, IP 20 Protection, wall mounted type, Slim LED Batten with polycarbonate housingand diffuser, elegant design with end caps, having excellent thermally managed polycarbonate extrution, LM 80 Certified LED having Integral Electronic Constant Current Driver , IP 20 Protection, Opreating voltage 240 V , 50Hz AC Supply and Operating tempraeture 0 to 50 C, Power factor ≥ 0.9, Lumen output ≥ 2000, necessary mounting arrangements on PVC Square box 2 Nos, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white color flexible pipe complete all as specified Make Orient, Philips, Crompton, Havells etc

S & F for LED tube light fitting 10 Watt, 2 Feet or 591 MM in length, IP 20 Protection, wall mounted type, Slim LED Batten with polycarbonate housingand diffuser, elegant design with end caps, having excellent thermally managed polycarbonate extrution, LM 80 Certified LED having Integral Electronic Constant Current Driver, IP 20 Protection, Opreating voltage 240 V , 50Hz AC Supply and Operating tempraeture 0 to 50 C, Power factor ≥ 0.9, Lumen output ≥ 1000, necessary mounting arrangements on PVC Square box 2 Nos, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white color flexible pipe complete all as specified Make Orient, Philips, Crompton, Havells etc

S & F Energy saving new generation 10/12 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. Make Orient, Philips, Crompton, Havells etc

S & F sheet metal enclosure Geyser / AC Box having 20 Amp MCB SP as incomer complete all as specified

Fixing Only water heater storage type (Geyser) vertical type, with steel inner container of capacity 25 Ltr, power Consumption 2 KW, BEE 5 star rated pressure rating >8 Bar, Powder coated metal body with PUF insulation electrically operated 230 Volt Complete all as specified. NOTE :- Geyser shall be issued under Sch 'B' free for fixing only.

M & L for PVC connection pipe (copper) chromium plated 8 mm dia both end threaded incl brass coupling bolt cone washer complete , length of pipe is not less than 450 mm suitable for Hot/ cold water system complete as all specified and directed.

Taking down ceiling fan / Exhaust fan of any sweep sealing cable end dismanting blade and removing fan and blade to store complete all as specified and as directed.

M & L for Painting of ceiling fan/ Exhaust fan complete in situ with synthetic enamel paint by spraying including filling cavity with filler one coat after cleaning all dust etc complete all as specified and as directed.

Fixing only exhaust fan and connecting up including provn of cable from ceiling rose or connector to fan complete all as specified and as directed.

Supply & Laying, testing & commissioning of LT UG cable XLPE sheathed PVC insulated,screened PVC bedded, galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volts grade, laid in trenches/ surface of wall/ in GI pipe along with pole for connection to OH lines,including brass cable glands,clamps,etc and making good damaged surfaces as required of 10 Sqmm 2 Core sizes complete all as specified

M&L for sand cushioning to underground PVC/XLPE cable with tibba sand and punning to provide required cover complete all as directed by Engineer-in-Charge. (Note :- For the purpose of payment only punned thickness will be measured).

Supplying and laying Jodhpur stone quarry faced stone slab cover 25 to 30 cm in width, 50 to 60 cm long and 40 to 50 mm thick, laid dry and abutting each other with gap between adjacent slab not exceeding 10 mm over under ground cables for protection complete all as specified & directed by Engineer-in-charge.

S&F 40 mm bore GI tubing “light grade” in trenches/ on pole for protection of cables complete all as specified & directed by Engineer-in-charge.

S & F ceiling fan 1200 mm Sweep Single phase, 230/240 Volts BEE 5 Star rating without fan regulator and with fan downrod, flexible copper wire for electrical connection from ceiling rose to fan connector complete all as specified Make. Bajaj, Orient, Crompton

M/S SHRI HARI CONSTRUCTION COMPANY

Bhawani Constructions

MAHAVIR CONSTRUCTION CO