MODIFICATION OF ORP BLAST PEN AT AF STN NAL

Amount

Taking down chowkats or frame with shutters (without taking off shuttters from frames) size exc 1.5 Sqm but not exc 4 sqm each and removing from site and making good disturbed surfaces as per existing specifications complete all as specified and as directed.

Taking down chowkats or frame with shutters (without taking off shuttters from frames) size n .exc 1.5 Sqm and removing from site and making good disturbed surfaces as per existing specifications complete all as specified and as directed.

Supply and fixing in opening complete solid PVC door frame of size 50mm x 47mm made out of 5 mm wood grain printed colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick(Style) consisting of frame made out of M.S. tube for top & bottom rails. MS frame shall be covered with heat moulded wood grain printed colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside width solvent cement for stiles and plain colour PVC sheet for top rail, Lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement fixing in frame at site complete all as specified and as directed.

Supply and fixing 200mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

Supply and fixing Stainless steel butt hinges, 100 mm long, medium weight, cold rolled fixed with steel screws or welded to angle iron frame where required complete all as specified and as directed.

Supply and fixing 250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed with screws complete all as specified and as directed.

Supply and fixing 150mm aluminum handles cast type anodized complete all as specified and as directed.

Demolition of cement concrete (unreinforced) ground floors and paving n.exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete(unreinforced) of any description and in any position not otherwise specifically provided for any thickness complete all as specified and as directed. NOTE : Demolition area should be isolated by cutting through diamond cutter to prevent development of cracks in adjecnt concrete surface area.

Material and labour 25mm thick cement concrete type-B0, 1:2:4 using 12.5 mm graded crushed stone aggregate as in floor finished even and fair complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M & L for glazed ceramic coloured tiles in vertical surfaces 350 x 250 x 7mm/450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in cement mortar (1:4) to receive tiles complete all as specified and as directed.

Material and labour for non/Anti skid coloured ceramic tiles of size 7-8 mm thick area of each tiles exceeding 0.11 Sqm but not exc 0.18 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement with pigment to match the shade of tiles over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. Note : Top finish of pattern of Anti skid as approved by GE.

Material and labour for Vitrified ceramic tiles 10mm thick light shade (Square/ rectangular) polished, area of each tiles n. exc 0.36 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

Material and labour for Vitrified ceramic tiles 10mm thick light shade (Square/ rectangular) polished, area of each tiles n. exc 0.36 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match in vertical surface such as skirting, dado and risers over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Taking down cement plaster including racking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed.

Material and labour for rendering 15mm thick cement plaster in CM 1:6 to brick or concrete wall surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour rendering 15mm thick cement plaster in CM 1:4 to brick or concrete wall surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Supply and fixing 10 liters capacity PVC valveless syphonic action type flushing cistern low level, White, with inlet ball valve, float, and handle including 32mm dia PVC flush pipe for low level cistern including bracket fixed in repairs complete all as specified and as directed.

Supply and fixing in repairs 15mm dia brass chromium plated fancy type bib tap with crutch or butterfly handle with long shunk / neck screwed down, screwed for iron pipe complete all as specified and as directed.

Supply and fixing in repairs vitreous china squatting pan, orissa pattern size 580mm x 440mm white with integral foot rests (excluding flushing cistern and flush pipe) complete including provn of lime concrete bedding complete all as specified and as directed.

Supply and fixing in repairs vitreous china white wash down water closet (pedestal pattern) including connection to drain (or out going pipe), flushing pipe and anti-syphonage pipe etc, complete all as specified and as directed.

Supply and fixing in repairs plastic water closet seat, white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

Supply and fixing in repair vitreous china wash hand basin, flat back of size 550mmx400mm, white including brackets complete all as specified and as directed.

Supply and fixing PVC connection 15mm size with PTMT nuts 450mm length complete all as specified and as directed.

Supply and fixing sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections including cleaning for refixing complete all as specified and as directed.

Supply and fixing 15 mm bore steel water tubing galvanised, medium grade fixed to walls and ceiling or in floor complete all as specified and as directed.

Fixing only 15 mm bore steel water tubing galvanised, medium grade fixed to walls and ceiling or in floor complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections including cleaning for refixing complete all as specified and as directed.

Supply and fixing 20 mm bore steel water tubing galvanised, medium grade fixed to walls and ceiling or in floor complete all as specified and as directed.

Fixing only 20 mm bore steel water tubing galvanised, medium grade fixed to walls and ceiling or in floor complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of andings, steps, for concealed water tubing or concealed conduit wiring etc and making good cutting not exceeding 10 cm girth

Supply and fixing grating doom 100 mm dia of PTMT(minimum weight 25 gms) complete all as specified and as directed.

Supply and fixing grating doom 100 mm dia with hole of PTMT(minimum weight 25 gms) complete all as specified and as directed.

Supply and fixing in repairs stop valve/angle valve ISI marked, size 15 mm dia, cast copper alloy, fancy type chromium plated screwed down, high pressure with crutch or butterfly handle srewed both ends for iron pipe & fixed complete all as specified and as directed.

Supply and fixing 20 mm ball valve high pressure PTMT with epoxy coated aluminium rod & high density pastic ball screwed for iron pipe and fixed complete all as specified and as directed.

Supply and fixing in repairs waste fittings 32 mm dia brass chromium plated for glazed ware sinks, basins etc with long screwed shanks and fly nuts flange end bedded in red lead complete all as specified and as directed.

Disconnecting and taking down, water storage tanks of any description of capacity exceeding 250 ltrs but not exceeding 500 ltrs and setting aside for refixing or removing to store etc. complete all as specified and as directed.

Supply and fixing 500 ltrs capacity, double layered rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position making connections all as specified in SSR Part-I complete all as specified Make : Syntex, Aquaplus, Diplast, Ganga

Supply and fixing in repairs shower rose chromium plated with or without swivel joints any size including fixing to steel pipe or union of 125mm size complete all as specified and as directed.

Supply and fixing Tublar towel rail brass chromium plated 20 mm dia D type 60 cm long between flanges complete all as specified and as directed.

Supply and fixing in repairs venition blinds, sheer demount blinds with aluminium roller tuber cassette any colour fabric weight 140 gms, light control 70% fabric composition 100% polyester complete all as specified and directed

Supply and fixing 15 mm dia stop valve (concelled type) cast copper alloy screwed down high pressure with crutch or butterfy handle with long shank and cup complete all as specified and as directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets and wood scantling complete all as specified and as directed.

Material and labour for repairing RCC projection chajja, facia, bands, shelves, beams, RCC railing, coloumns, balcony and similar works by dismantling of loose/disintegrated portion of RCC at any height and in any position/floor (including provn of support, formwork and welding of reinforcement if required with welded mesh of weight n. exc 3kg/sqm, finished even and smooth to desired shape and applying two coats of weather proof emulsion paint to match the shade of exsting surface complete all as speciified and directed. Note : Unit rate of this item includes the cost of scafolding formwork, etc and nothing extra shall be paid on account of variation in height.

Supply and fixing sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.

Material and labour for Granite 20 mm thick of any type work (table rubbed and polished) as in cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite over and including 15 mm screed bed in cement mortar (1:6) complete all as specified and as directed.

Supply and fixing PVC wall lining consisting of 5 mm thick wood grain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing complete all as specified and as directed.

Supply and fixing 5 mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC frame as specification and drawing complete all as specified and as directed.

All as per item No 53 here in before but area exc 1.00 Sqm but n exc 2.00 Sqm each complete all as specified and as directed.

Supply and fixing factory made uPVC white colour casement (openable) door made of extruded profile with wall thickness of 2.3 mm (-0.2 mm). Window profile with hollow section with multi chamber, frame (60 mm x 58 mm). Sash (60 mm 78 mm). T profile (One vertical length in between two shutters) (60 mm x 74 mm). Glazing bead (35 mm x 20 mm will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainge of water etc, making arrangement for fixing of harware. EPDM gasket 1.2 + - 0.2 mm thick galvanized steel frame (28 mm X 21.5 mm). sash (31 mm X 27 mm). T profile will be fixed to the wall with 8 mm x 100 mm long fasteners. Hardware: [ casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild steel with multi point locking system with strikes. 3D hinges of zine alloyed (white powder coated)] and 5 mm thick glazing with seleeted quality glass complete all as specified and as directed. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.

Supply and fixing DGU Panel (Glass system shall be 5 mm reflective toughened glass + 10 mm air gap between filled with inert gas and hermetically sealed + 5 mm toughened glass) complete all as specified and as directed.

Supply and fixing rolled mild steel in joist, channel, angle or tee section fixed independently, with out connection plates etc (cut to ordinary length i.e with in 20 mm of length indicated) of Fe-290 Gde E-165 complete all as specified and as directed.

Supply and fixing mild steel steel work in tubular trusses, post, rafter and purlin including tubular trusses including special shaped washer etc using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240 complete all as specified and as directed.

Supply and fixing framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

Supply and fixing mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30 cm long dia of neck exc 12 and n exc 20 mm complete all as specified and as directed.

Making holes drilled up to 12 mm dia (and countersunk, if required) exc 12 but n exc 25 mm depth of hole complete all as specified and as directed.

Supply and fixing 4 mm dia plain mild steel wire galvanised class 3, in fencing including straining and fixing to wood, concrete or steel posts and or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staplles or steel pins, etc complete all as specified and as directed.

Supply and fixing fasterners of 150 mm length & 12 mm dia complete all as specified and as directed.

Providing cement concrete in lintels up to 1.5m clear span cills steps; seismic and other similar bands plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, coping, kneelers, apex stones bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating in type B-1, 1:2:4 using 20 mm graded aggregate complete all as specified and as directed.

Material and labour preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Supply and fixing for providing kitchen cabinet in required size at site made out of 12 mm thick both side plain sheet consisting of Carcass 18 mm thick PVC sheet and provisioon of shutters made out of 18 mm thick one side decorative laminated PVC sheet all required brackets SS screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as per drawing and specification approved by Engr-in-charge complete all as specified and as directed.

(a) 12 mm thick plain sheet

(b) 18 mm thick plain sheet

(c) 18 mm thick sheet prelaminated one side

Supply and fixing continuous (piano) hinges SS, bright finish 30mm flaps complete all as specified and as directed.

Supply and fixing aluminium handles 75 mm cast type anodised complete all as specifid and as directed.

Supply and fixing magnetic catcher for kitchen cupboard complete all as specifid and as directed.

Material and labour preparation of old plastered wall surfaces and applying two coats of weather coat on concrete or brick surfaces in camouflage pattern complete all as specifid and as directed.

Material and labour preparation of old plastered wall surfaces and applying two coats of white wash on concrete or brick surfaces complete all as specifid and as directed.

Supply and fixing of chromium plated health faucet with flexible pipe complete all as specifid and as directed.

Supply and fixing Brass chromium plated centre hole basin mixer for mixing hot & cold water screwed down for iron pipe 15mm bore complete all as specifid and as directed. Make :- Pryag / JAQUAR / GEM / MARC / JALANGI

Supply and fixing brass chromium plated wall mixer for mixing hot and cold water screwed down for iron pipe 15 mm bore complete all as specifid and as directed. Make :- Pryag / JAQUAR / GEM / MARC / JALANGI

Supply and fixing brass chromium plated sink mixer for mixing hot and cold water screwed down for iron pipe 15 mm bore complete all as specifid and as directed. Make :- Pryag / JAQUAR / GEM / MARC / JALANGI

Surface dressing not exceeding 15 cm deep in soft/loose soil complete all as specified and as directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation etc or for shafts wells cesspits manholes pier holes etc n exc 10 sqm on plan and n exc 1.5 mtr in depth and getting out in hard and dense soil complete all as specified and as directed.

Excavation in post holes (or similar holes) each n exc 0.5cum getting out returning filling in and ramming earth or broken rubbles mixed with earth around in layers not exc 25 cm, watering and removing surplus soil to a distance n.exc 50 m in soft and loose soil complete all as specified and as directed.

Excavating over areas, n exc 1.5 m deep and getting out in hard/ dense soil complete all as specified and as directed.

Excavating over areas, exc 1.5 m but n exc 3.0 m deep and getting out in hard/ dense soil complete all as specified and as directed.

Excavating over areas, exc 3.0 m but n exc 4.5 m deep and getting out in hard/ dense soil complete all as specified and as directed.

Excavating over areas, exc 4.5 m but n exc 6.0 m deep and getting out in hard/ dense soil complete all as specified and as directed.

Excavating over areas, exc 6.0 m but n exc 7.5 m deep and getting out in hard/ dense soil complete all as specified and as directed.

Supply and fixing Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strenth of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Material and labour brickwork with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

Material and labour brickwork with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:4 complete all as specified and as directed.

Material and labour for Brick work with subclass ‘B’ bricks, honeycomb brick walling straight or curved on plan one brick thick to any radius, built in CM 1:4.

Material and labour for Brick work with subclass ‘B’ bricks, honeycomb brick walling straight or curved on plan one and half brick thick to any radius, built in CM 1:4.

Material and labour preparation of new plastered surfaces and applying two coats of cement base paint complete all as specified and as directed.

Material and labour for cement concrete type C-2, 1:3:6 using 40 mm graded aggregate in foundations, filling and mass concrete complete all as specified and as directed.

Material and labour 100 mm thick PCC type D-2, 1:4:8 using 40 mm graded crushed stone aggregate as in sub base complete all as specified and as directed.

Material and labour for cement concrete type D-2, 1:4:8 using 40 mm graded aggregate in foundations, filling and mass concrete complete all as specified and as directed.

Material and labour machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigment complete all as specified and as directed. Note : Pattern of top finish of paver block as approved by GE.

Material and labour for sand filling under floors or in foundations including watering consolidation and protection of underground cable complete all as specified and directed.

Material and labour 100 mm thick cement concrete type C-2, 1:3:6 using 40 mm graded aggregate in sub base complete all as specified and as directed.

Material and labour 100 mm thick cement concrete type B-2, 1:2:4 using 40 mm graded agregate laid in alternate pannels of not less than 2.50 Sqm in each with broom finish on top surface complete all as specified and directed.

Material and labour cement concrete type B-2, 1:2:4 using 40mm graded aggregate in surface channels and drains complete all as specified and as directed.

Extra for froming fair finished drain or channel 30cm inner girth in cement concrete using ex-tra cement, including forms moulds mitred/stopped ends etc complete all as specified and as directed.

M & L for Reinforced concrete pipes, class NP2 , 300 mm bore pipe laid and jointed complete with collars complete all as specified and as directed.

M & L cement concrete bed to drain pipes of 300 mm bore with cement concrete type C-2, 1:3:6 including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed.

Material and labour for providing precast cement concrete Type B1 (1:2:4) using 20mm graded aggregate as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in cement mortar 1:6 complete all as specified and as directed.

Supply and fixing solar stud of size 125X125X22 mm made from aluminium alloy and PC constuction, monocrystal solar panel and reachargeable battery with view distance approx 1000 mtrs, electronically operated fix with epoxy adhesive sealing compound as per manufactures instruction complete all as specified and directed.

Material and labour for earth filling under floor or in foundation including watering and consolidation with material retrived from excavation complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm thick complete all as specified and as directed.

Removing excavated or demolished material to a distance exc 1.5 Km but not exc 5 Km and deposited where directed complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

Material and labour for cement concrete 1:2:4, type B1 using 20 mm graded aggregate in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses. Lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating incl necessary form work complete all as specified and as directed. .

Material and labour for RCC 1:2:4 type B1 (nominal mix) using 20 mm graded stone aggregate as in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and as directed.

Formwork for rough finished concrete curved surface to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Formwork to edges of rough finished surfaces of concrete flats, treads, breaks in floors, window cills, concrete railings,openings in concrete walls, floor and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5 cm but n exc 10 cm wide complete all as specified and as directed.

Material and labour for loose filing with broken bricks of guage 80 to 150 mm in soakage pits, soakage wells complete all as specified and as directed.

Supply and fixing Cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters and similar articles.each article exc 5.0 KG complete all as specified and as directed.

Supply and fixing mild steel 'TMT' bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Taking down DB/ main switch of any size and making good disturbed surface of wall/ floor complete all as specified and as directed. Note:- Temporary power supply shall be provided by contractor.

Taking out carefully the existing burnt sub main wiring of size 4 Sqm / 6 Sqmm PVC insulated multi stranded aluminum conductor cable along-with earth continuity conductor from the PVC / rigid steel, concealed/surface conduit and making good the distubed surface complete all as specified and as directed.

Taking down carefully point wiring (Light, fan, socket) including fittings such as switches, Ceiling roses, pendants, regulator, sockets etc removing from site of work and making good to the disturbed surfaces of walls/floors etc complete all as specified and as directed Note:- Temporary power supply shall be provided by contractor.

Supply and laying Sub main wiring complete with 03 runs (Phase, Neutral & Earthing colour code) of single core 4 sqmm fire retardant low smoke (FRLS) PVC insulated copper conductor cable multistranded and sheathed LT 1100 V grade drawn through and including metalic regid steel conduit 20 mm dia ISI marked and all accessories on surfaces and making good the disturbed surface complete all as specified and as directed Note :- 2 run of 4 sq mm , 1 run of metallic rigid steel conduit & 1 run of 4.00 sqmm cable shall be measured as single unit length.

Supply and laying Sub main wiring (concealed) complete with four single core 6 sqmm fire retardant low smoke (FRLS) PVC insulated unsheathed multi stranded copper conductor cable LT 1100 V grade drawn through in 32 mm dia steel conduit and conduit accessories including 6 sqmm fire retardant low smoke (FRLS) PVC insulated unsheathed multi stranded copper earth cable connected to common earth dolly complete on surfaces and making good the disturbed surface complete all as specified and as directed Note :- 4 run of 6 sq mm , 1 run of metallic rigid steel conduit & 1 run of 6 sqmm cable for earth wire shall be measured as single unit length.

Material and labour for Point wiring with PVC insulated fire retardant low smoke (FRLS) multi stranded copper conductor cable of 1.5 sqmm in and including stove enamelled Steel Conduit heavy duty (ISI mark) on surface and pressed steel terminal boxes (for mounting switches / sockets /regulators / ceiling roses etc) made out of MS sheet not less than 1.6 mm thick including painting with one coat of red oxide primer on internal and external surface covered with 3 mm thick laminated plastic sheet ISI marked including 1.5 sqmm PVC insulated fire retardant low smoke ( FRLS) multi stranded copper conductor cable as earth continuity wire connected to common earth and each terminal box/fitting complete all as specified and directed . Note :- (i)The wiring shall be provided in standard colour code i.e. Red for Phase, Black for Neural and Green for earth. (ii) The quoted rate is deemed to include for cutting/chasing for concealing terminal boxes etc and making good the surface to match the existing surfaces. (iii) In case of ceiling portion where concealed is not possible, the surface conduit shall be provided as directed. (iv) The earth wire shall be connected to common earth and each terminal boxes and fitting all as directed.

(a) One light point controlled by one switch

(b) One ceiling fan/wall fan point controlled by one switch

(c) One exhaust fan point contrelled by one switch

(d) One switch socket outlet 3 pin 6 Amp on same board.

All as per description of serial item No. 119.00 here in before but one 3 pin socket outlet 5 Amp on independant board.

All as per description of serial item No. 120.00 here in before but for One 3-pin socket outlet 15 Amp on independent board with 4 sqmm FRLS cable including 2.5 sqmm FRLS multistranded copper cable as earth continuity wire.

Supply and fixing energy saving decorating box type batten light fitting 230 volts surface mounted complete with high effeciency PMMA diffuser soft glare free light LD lamp 20 watt blue coloured end caps with all accessories, pre- wired, including providing flexible copper wire twin core cable complete all as specified and directed by enginer in charge. Make :- Havelles /Philips /Wipro/ crompton

Suply and fixing bulk head luminaries 10 wattt , 230 volts wall mounted complete with all accessories , pre wired , including provided flexible copper wire, twin core cable complete all as specified and directed by engineer -in-charge. Make-Crompton Greaves/philips/ bajaj/havells.

Suply and fixing Lamp holder angular PVC polycarbonate type with back plate suitable for PVC casing capping/conduit fitting complete all as specified and as directed Make :- Anchor/Plaza/Crabtree

Supply and fix LED bulb 9 watt with lumen 850 complete all as specified and as directed. Make :- Havells /Philips/ CG/ Wipro

Supply and fixing stepped type electronic fan regulator 100/120 watt , SP 230 Volt 100 watt complete all as specified and as directed.

Supply and fix socket out let 5 pin 6 amp multipurpose, flush type complete all as specified and as directed.

Supply and fix Socket out let 2 in 1, 3 pin, 5 and 15 amp multipurpose, flush type complete all as specified and as directed.

Supply and fix Switch piano flush type single pole one way 5/6 amp complete all as specified and as directed.

Supply and fix Switch piano flush type single pole one way (multi pin) 16 amp complete all as specified and as directed.

Supply and fix Ceiling rose surface Bakelite 65 x 50 mm three terminals complete all as specified and as directed.

Supply and fixing sheet metal enclosure three pole, neutral and earth encolsure with a three pin and earth plug with socket complete with one triple pole MCB encolsure complete with provision for fixing of one MCB TP 32 Amps 415V complete all as specified and as directed.

Supply and fixing sheet metal enclosure single pole and neutral encolsure with two pin and earth plug and socket complete with provision for fixing of one MCB SP 20 Amps complete all as specified and as directed.

Supply and fixing vertical TPN DB double door suitable for fixing 100 amp MCCB, IP 45 protection with powder coated enclosure 4 way insulated busbar assembly rating 200 Amps including MCCB 4 pole, 415 V, 100 A, 16 kA - 01 No complete all as specified and as directed. Make : L&T / Legrand/ Havells.

Supply and fix sheet metal enclosure for SPN DBs with double door for incorporating MCBs IP 43, 8 way with 200 amp rated busbar, 240 volts as per IS 8623, including taking down old unserviceable single phase DBs, all as specified and directed. Make :- Legrand /L&T/Havells

Supply and fix sheet metal enclosure for DBs with double door for incorporating MCBs IP 43, TPN 4 way with 200 amp rated busbar, 415 volts as per IS-8623 including taking down old unserviceable DBs complete all as specified and as directed. Make :- Legrand /L&T/Havells

Supply and fix MCB four pole 63 Amps 16 KA conforming to IS-8623, 415 volts 50 Hz including making necessary incoming and outgoing connection with suitable size of copper lugs etc. complete all as specified and as directed. Make :- Legrand /L&T/Havells

Supply and fix MCB SPN 32 Amps 10 KA 240 volts 50 Hz including making necessary incoming and outgoing connection with suitable size of lugs etc. complete all as specified and as directed. Make :- Legrand /L&T/Havells

Supply and fix MCB SP 6 to 32 Amps 10 KA 'C' curve 240 volts 50 Hz including making necessary incoming and outgoing connection with suitable size of lugs etc. complete all as specified and as directed. Make :- Legrand /L&T/Havells

Material and labour for taking down fan, sealing cable end, dismantling blades and removing fan and blades to keep store and including after copletion of civil work hanging ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as spcified and as directed.

Supply and fix LED post top lamp spherical shape with polycarbonate diffuser and IP 65 protection 25 W, LED warm white complete all as specified and as directed. Make Bajaj / Havells / Eveready / Philips / Polycab

Supply and fixing heavy duty air circulator wall mounted fan 450 mm sweep 1400 rpm, 230 V 50 Hz metal body with self opening louvers incl all mounting accessories and making connections using three core copper conductor cable connected from ceiling rose to fan and marking MES No in black paint and making good in cement mortar 1:4, and matched with existing surface complete all as specified and as directed. Make : Havells /Khaitan/ Usha / Bajaj / Crompton

Supply and fixing heavy duty exhaust fan 300 mm sweep 1400 rpm, 230 V 50 Hz metal body with self opening louvers incl all mounting accessories and making connections using three core copper conductor cable connected from ceiling rose to fan and marking MES No in black paint and making hole / opening of suitable size in existing wall and making good in cement mortar 1:4, and matched with existing surface complete all as specified and as directed. Make : Havells /Khaitan / Usha / Bajaj / Crompton

Supply, install, testing and commissioning of storage type electric water heater 25 ltrs capacity, vertical closed type with stainless steel inner container 2000 watts 5 star rated complete all as specified and as directed. Make : Havells /Venus/ Usha /Jaquar

Material and labour for earthing complete with GI earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly in ground vertical position , earth pit not less than 3.00 Mtr deep below ground level with top edge of the plate not less than 2.4 Mtr below ground level. The earth plate to be connetced with galvanised iron earthing strip of size 32 mm x 6 mm by means of nuts, bolts, chcek nuts and washers made of galvanised iron or steel earthing strip to be protected by galvanised iron pipe 40 mm bore (medium grade) up to ground level and there after with 40mm dia HDPE pipe up to test point. Earthing shall be include with providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) up to 90 cm all around earth plate further filled with 60 cm thick Tibba sand. Earthing shall also be include for providing concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work complete all as spcified and as directed.

Supply and fixing 32 x 6mm galvanised iron strip as earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe through wall /floor / roof or fixed to poles or any other indicated situation for loop earthing etc. as required complete all as specified and as directed. Note:- (i) Excavation & earth work shall be measured and paid for separately. (ii) Cutting holes in the wall and making good with cement plaster / mortar alongwith distemper / white wash is deemed to be included in the rate quoted. (iii) Cost of Insulators required for fixing of strip including nuts and bolts is also included in the unit rate quoted.

Taking out defective GI pipe of any size from trenches, from wall, under floor etc, complete all as specified and as directed. Note : (i) Excavation and earth work shall be measured and paid for separately

Supply, laying, jointing and testing of 40 mm bore GI water tubing medium grade, with all fittings like elbow,socket,Tee, flange etc and laid in trenches complete all as specified and as directed. (Make : TATA/ JINDAL/ SURYA)

Supply, laying, jointing and testing of 25 mm bore GI water tubing medium grade, with all fittings like elbow,socket,Tee, flange etc and laid in trenches complete all as specified and as directed. (Make : TATA/ JINDAL/ SURYA)

Supply, laying, jointing and testing of 15 mm bore GI water tubing medium grade, with all fittings like elbow,socket,Tee, flange etc and laid in trenches complete all as specified and as directed. (Make : TATA/ JINDAL/ SURYA)

Supply & fixing 40mm dia gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing 25mm dia stop/gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing 15mm dia stop/gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-Charge.

Supply and installation air conditioner 1.5 TR capacity air cooled hi wall split type remote controlled with indoor and outdoor units duly connected with inlet & outlet gas copper tubes duly insulated with insulation material complete and with in-built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and BEE 3.2, gas filling, fixed on MS stand fixed to wall/floor with nuts and bolts, PVC insulated sheathed connection cable 3 core for indoor & outdoor units, PVC flexible water pipe upto floor level, making necessary holes for passing of pipes and making good complete all as specified and as directed. Make: O General / DAIKIN / Hitachi Note: The cost of condenser / refrigerant tubes between indoor and outdoor unit, irrepective of length, shall be deemed included in the unit quoted rate of this item. Contractor is advised to visit the site before quoting the rates. Nothing extra shall be admissible for the tubes provided in addition to those supplied by the manufacturer with the AC.

Supply and installation air conditioner 2 TR capacity air cooled hi wall split type remote controlled with indoor and outdoor units duly connected with inlet & outlet gas copper tubes duly insulated with insulation material complete and with in-built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2, gas filling, fixed on MS stand fixed to wall/floor with nuts and bolts, PVC insulated sheathed connection cable 3 core for indoor & outdoor units, PVC flexible water pipe upto floor level, making necessary holes for passing of pipes and making good complete all as specified and as directed. Make: O General / DAIKIN / Hitachi Note: The cost of condenser / refrigerant tubes between indoor and outdoor unit, irrepective of length, shall be deemed included in the unit quoted rate of this item. Contractor is advised to visit the site before quoting the rates. Nothing extra shall be admissible for the tubes provided in addition to those supplied by the manufacturer with the AC.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 270 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity suitable for 1.5 TR Air conditioner complete all as specified and as directed.. Make V Guard / Microtek/ Bluebird

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 270 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity suitable for 2.0 TR Air conditioner complete all as specified and as directed. Make V Guard / Microtek/ Bluebird

Supply installation, commissioning of Refrigerator, electric driven (single phase) 240 Volt 50 Hz capacity upto 195 ltr BEE 5 star rated or next higher capacity floor mounted with all fixed accessories as per OEM and PVC stand complete all as specified and as directed. Make :- LG/ Samsung / Godrej/Haier

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 130 V to 290 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity suitable for refrigerator 195 ltr complete all as specified and as directed. Make V Guard /Microtek/ Bluebird

Supply and fixing sheet metal enclosure single pole and neutral encolsure with two pin and earth plug and socket complete with provision for fixing of one MCB SP 20 Amps complete all as specified and as directed.

Supply, installation, testing and commissioning of silent Diesel Engine driven generating set with AMF panel 20 KVA with water cooled engine of suitable BHP for 16 KW power genaration @ RPM 1500, brushless frame with silencer and canopy for sound less mode (sound level not exceeding level specified by central polution board) and all engine accessories such as self starter, alternator/ dynamo and 16 KW/20 KVA electric alternator 415 Volts 3 phase, 4 wire, 50 Hz, insulation class H coupled to engine with suitable coupling and base frame on foundation as recommended by the manufacturerand consisting of other electrical components, fuel tank of suitable capacity with level indicater, Power command genset controller, fuel pipes,Duel spin or fuel filter Dritype aircleaner, shut off coil with safeties for LLOP/HWT, fuel pipes, bar metre, hour meter, oil temparature guage, ammeter, ignition switch, radiator with cooling system, maintenance free battery, including suitable size of copper cable leads with terminal, all mountings, accessories and necessary foundation and AVM pads complete as per manufaturer recommendations and all as specified and as directed. Make :- MAHINDRA/CUMMINS/ASHOK LEYLAND/KIRLOSKER

(A) Prime Mover :- Suitable for driving 16 KW/20 KVA alternator water cooled battery start Diesel Engine of adequate capacity confirming of IS -10001/1002 and fuel tank suitable for 12 hrs running capacity and capable of taking 10 % over load for one hrs in any 12 hour opertaion complete with the following standard accessories:- (a) Fly wheel to match with the flexible coupling (b) Flexible couipling with gu ard (d) lubricating oil filter , fuel filter paper element type (e) Air cleaner oil bath type/dry type (f) Blower type fan and radiator (g) Governor of class A Governing as per IS 1601 of DS 649/1958 (h) Startor , motor for elctric start complete with dynamo alternator, lead acid batteriesheavy duty of capacity 12 V 150 AH or adequate size and length not less than 2M including battery box all as directed. (j) Hour meter and RPM indicator (k) Exhoust pipe through out side the building. and lagging of entire length of exhaust pipe with 12 mm dia. (l) Instrument panel duly wired comprising the following including protection for low lube oil high temperature (m) Lube oil presure guage (n) Battery charge indicter meter (o) Starting switch with key (p) Lub oil temparature (q) Water temparature

Note :- (i) Any fittings/ fixtures which are necessary for proper functioning of the DG set shall also be deemed include in the unit rate quoted . (ii) Necessary foundation for installation of DG set shall also be provided as per manufacturers recommendations and cost deemed to be inclusive in the rate quated for this item. (iii) All testing equipments are to be arranged by the contractor and testing shall be carried out by the contractor in presence of Engr in Charge and rep of accepting officer and testing result duly signed by the Engr- in- Charge and the contractor shall be kept in record. (iv) Rate quated by the contractor including the rate of first filling of lubricating oil, coolant and GI pipe wrapped with insulation material upto out side of wall. (v) Drawings / cataloge for DG set and AMF panel got approved by the GE before odering to the manufaturer (vi) Diesel required for testing of DG Set shall be procured by the contractor without any extra cost.

Material and labour earthing complete with copper earth plate electrode 600 mm x 600 mm x 3.15 mm thick, burried directly in ground in vertical position, earth pit not less than 3.65 Mtr deep below ground level with top edge of the plate not less than 2.90 Mtr below ground level. The earth plate to be connetced with copper earthing strip of size 20 mmx 3mm thick by means of brazing between copper strip and earth plate min 45 cm in vertical length and copper strip also to be joined by brazing only. The copper earthing strip to be protected by galvanised iron pipe 40 mm bore (medium grade) up to ground level and there after with 40mm dia HDPE pipe up to test point. Earthing shall include provision of funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) up to 90 cm all around earth plate further filled with 60 cm thick Tibba sand and 2nd layer with 30 cm of Magnesium sulphate powder (compact thickness ), 3rd layer with tibba sand up to ground level. Earthing shall also include concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 3 of MES Schedule Part-I complete to obtain less than 2 Ohm earth resistance value complete all as specifiedand as directed. NOTE : (i) Cost of this items includes the scope of earth work, charcoal, salt, PCC, RCC pit cover of required size. (ii) Tibba sand shall be arranged by the contractor at his own and the cost thereof shall be deemed included in unit quoted rate of this item. (ii) Electrical Plate No. 3 refrred in the item above is mainly for earth chamber.

Material and labour for copper strip 20 x 3.15 mm with proceline insulator and fixing screws etc for roof conductors and down conductors above the ground complete all as specified and as directed.

Supply and fixing Air termination single pointed copper rod 12mm dia and 300 mm long complete all as specified and as directed.

Material and labour for earthing continuity conductor or main earthing lead fixed to wall on batten on recess or chases or buried in ground or dawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc. as required of size 32 x 6 mm copper strip for net connection complete all as specified and as directed.

Supply and fixing HDPE pipe medium grade external dia 50 mm, exclusive of boxes (junction / terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and as directed.

Material and labour for making test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and as directed.

Supply and fixing galvanised steel tubes 40 mm bore medium grade with all fittings, for fixing air termination rod with suitable clamps, nuts, bolts etc including necessary welding where required complete all as specified and as directed.

Material and labour well burnt old size sub Class ‘B’ bricks, laid flat, in trenches for cable protection complete all as specified and as directed.

Taking out defective cable XLPE/PVC sheathed 1100 volt grade heavy duty armoured with aluminium conductor of any Cross sectional area from trenches, from wall/poles/under floor etc, removing the unserviceable cable complete all as specified and as directed. Note : (i) Excavation and earth work shall be measured and paid for separately (ii) Unit rate of this item is also includes the removal of brick/tile as cable protection, GI pipe and cable joint etc. and nothing extra shall be admissible on this account. (iii) After taking out the cables from the trench, serviceability of cable shall be checked by the contractor in presence of the Engr-in-Charge and nothing extra shall be paid on this account.

Supply and laying XLPE insulated, armoured, heavy duty, 1100 Volts grade aluminium conductor cable Cross sectional area 70 Sqmm, 3.5 core in trenches or fixed to wall / passing through pipe / pole and testing complete all as specified and as directed Note : (i) Excavation & earth work, Brick protection and sand cushining shall be measured and paid for separately,

Supply and laying XLPE insulated, armoured, heavy duty, 1100 Volts grade aluminium conductor cable Cross sectional area 35 Sqmm, 3.5 core in trenches or fixed to wall / passing through pipe / pole and testing complete all as specified and directed Note : (i) Excavation & earth work, Brick protection and sand cushining shall be measured and paid for separately,

Supply and laying XLPE insulated, armoured, heavy duty, 1100 Volts grade aluminium conductor cable Cross sectional area 25 Sqmm, 4 core in trenches or fixed to wall / passing through pipe / pole and testing complete all as specified and as directed Note : (i) Excavation & earth work, Brick protection and sand cushining shall be measured and paid for separately,

Supply and laying XLPE insulated, armoured, heavy duty, 1100 Volts grade aluminium conductor cable Cross sectional area 6 Sqmm, 4 core in trenches or fixed to wall / passing through pipe / pole and testing compete all as specified and directed Note : (i) Excavation & earth work, Brick protection and sand cushining shall be measured and paid for separately,

Supply and fixing conventional LED street light 70 watt 230 volts pressure die cast aluminium housing, heat resistant toughened glass with frame, IP protection IP.66 batter optics for uniform distribution having surge protection 5 KV, sealed driver complete all as specified and as directed. Make: Havells/Crompton/Bajaj/Surya

Supply and fixing conventional LED 70 W flood light fitting with lense, high luminous efficacy,protected to IP 65, toughened glass efficient high out put emitter LED for better distribution applicable for area lighting including electrical connection complete all as specified and as directed. Make Havells/Crompton/Bajaj/Surya

Supply and fixing LT Panel Outdoor type floor mounted free standing dust and vermin proof panel / DB with IP-55 protection, CPRI approved, frame fabricated out of 40mm x 40mm x 4mm angle iron, 3 mm thick CRCA sheet for entire outer panel with single door and locking arrangements & 1.6 mm for inner compartment with 40mmx4mm flat Iron, including Separate cubicle chamber with cable alley not less than 300mm width for installation/connecting switchgears with the main bus bar using aluminium bus link or copper conductor flexible wires suitable for switch rating and connecting outgoing terminals of the switchgear with terminal blocks of appropriate current rating using flexible copper wires duly terminated by cable lugs and thimbles, MS surfaces epoxy based powder coated, shade as approved over 2 coats of red oxide primer, surfaces pre-treated in seven tank process for de-greasing, de-rusting & Phosphated, panel having front and rear opening and provision for installation of separate cable alleys, busbar chamber and switchgear compartments, Provision in cable alleys for bottom cable entry for incoming & outgoing cables, affixing MV danger plate at suitable intervals / locations including erection, testing and commissioning complete all as specified and directed including the following fixtures amd fitments mentioned below:-

Outgoing:- Separate cubical chamber with a cable alley not less than 300 mm width for installation/connecting the following switch gear with the main bus bar using aluminium bus link or copper conductor flexible wires suitable to the switch rating and connecting outgoing terminals of the switch gear with terminal blocks of appropriate current rating using flexible copper wires duly terminated by cable lugs and thimbles. (i) MCCB, 4 pole 100 A, 25 KA -02 No (ii) MCCB, 4 pole 63 A, 25 KA -01 Nos (iii) MCB SPN 40 A 10 KA - 02 Nos Make of MCCB: Legrand / Seimens / Schneider / ABB Note:- (i) A clear space of 200mm shall be kept from floor level for switchgear compartment. (ii) Air ventilation breathers with exhaust fan plastic body 100mm sweep shall be provided for heat dissipation. Suitable sized knock-out holes for cable glands shall be provided. (iii) Each compartment shall be numbered/lettered as per the approved approved by GE. . (iv) Contractor shall submit the GA drawings of LT Panel for approval of GE before placing the bulk order.

Material and labour for boring in soft/ loose soil at a depth not less than 1.5 metre under road/PTT/pavement/ Hard standing etc by usingof ultra sounding technique and mechinery equipments suitable for and including laying HDPE pipe nominal outer dia 80 mm PE 80 PN- 6 ISI marked all as per IS 4984/2016 including fittings complete without damaging the surface complete all as specified and directed by Engineer in charge Note :- (i) Location of boring holes shall be decide by the Enginer- in- charge as per requirement , nothing extra shall be payable on account of variation in length of crossing of road /PTT/pavement /Hardstanding etc. (ii) During boring soil strata may be changed, hence nothing extra shall be paid to the contractor for boring of holes through different type of soil. Tenderer is hereby advised to keep in mind this aspect while quoting his rates.

Material and labour boring of road crossing of size 80 mm dia at suitable depth not less than 1 mtr by using machinery / equipments complete without damaging the surface for passing pipes / cables etc including removing excavated soil to a distance n exc 50m complete all as specified and as directed. Note : (i) Location of boring holes shall be decided by the Engr-in-Charge as per requirement, nothing extra shall be payable on account of variation in length of crossing of road etc. (ii) During boring soil strata may be changed, hence nothing extra shall be paid to the contractor for boring of holes through different strata/different type of soil. Tenderer is hereby advised to keep in mind this aspect while quoting his rates.

Supply and fixing integral LED aviation light comprising of aluminium housing with polycarbonate enclosure complete all as specified and directed. Make : Bajaj/ Philips/ Crompton/ Havells

Taking out old unserviceable copper earth strip include air termination rod, insulators and earth test point from site ans shifting serviceable earth strip for re-fixing or removing the unserviceable strip complete all as specified and directed. Note : After taking out the earth strip from the site serviceability of the same shall be checked by the contractor in presence of the Engineer-in-Charge for further use and nothing extra shall be paid on this account

Laying only copper strip of any sizes as down conductor/ roof conductor after soldering between earth strip and refixing the copper strip by providing new porcelain insulator or burried in ground or drawn in conduit including PVC conduit fixing arragement with wall/ roof all as per clause SSR Part-I and as directed.

SHREE GURU NANAK CONSTRUCTION COMPANY

RAJENDER ENTERPRISES

M/s Madan Gopal Vyas