SPECIAL REPAIR TO BLDG NO. P-1094, P-1095, P-1090, P-1091, P-1135 to P-1138, P-1145 to P-1148, P-1150, P-1151, P-1157 AND P-1158 OF ARMD REGT AT SRI GANGANAGAR MIL STN

Dismatiling brick tiles or terracing tiles, single layer on roofs and lime concrete/brick bat coba/ mud phuska complete all as specified and directed by Engineer - in - Charge.

OVERLAY- PU BASED ELASTOMERIC LIQUIED MEMBRANE SYSTEM FOR EXPOSED ROOF : Providing and applying polyurethane liquid roof waterproofing with improved water ponding capability, elastomeric high build liquid membrane for concrete roofs for exterior wall and exposed surface with solid content not less than 80% and solar reflective index not less than 106 as per (ASTM E1980-19)/tear strength ~20 N/mm (Free film, 14 days, +30 degree C) (ASTM D624) and tensile strength >= 2 N/mm2 (ASTM D4541), elongation 350 to 400% as per ASTM D412 and crack bridging ability upto 2mm. (a) After proper surface preparation, Apply one coat of Primer for PU coating as per manufacturers specification. (b) Apply 1st coat of ShaliUrethane® BTD (white) @ 650 gm / m²(minimum) or equivalent by brush / roller while prime surface is tacky, Spread waterproofing reinforced Glass Fiber mash of 45 GSM with overlaps of 50 mm in both directions when the surface is still tacky. Allow 1st coat to dry. (c ) Apply 2nd & 3rd coat of ShaliUrethane® BTD (white) @ 650 gm / m² (minimum) or equivalent by brush/roller. Make : Fosroc/Sika/Choksey/Bostik/STP/ Asian Paints/Berger Paints Note : (i) The Minimum dry film thickness (DFT) of roof treatment shall be 1.5mm if any shortfall in thickness of above treatment the same shall be achieved by additional coat. (ii) The procurement of material and execution of the work of water proofing treatment shall be carried out by authorised applicator approved by GE. (iii) The manufacturer/authorised applicator shall give a warranty for the performance & durability for 10 years.

M&L for levelling course for roof slab, Type B0, 1:2:4 (12.5 mm graded aggregate) for maintaining proper roof slope, filling the depression and finishing cement concrete surface even and smooth without using extra cement complete all as specified.

Taking down cement plaster including raking out joint, hacking for key & scrubbing down with water etc from wall/concrete surface/roof top and alike in any situation complete.

M&L, 15mm thick rendering in CM 1:6 on fair faces of brick or concrete wall surfaces finished even and smooth without using extra cement complete.

M&L, 15mm thick rendering/plastering on any face of brick wall or concrete surface consisting in two layers i.e. First laye 10 mm thick in cement mortar (1:4) and second (top layer) layer 5 mm thick in cment mortar (1:4) including mixing of liquid WPC in mortar @ as per manufacturer instructions per bag of cement of 50 Kg, finished even and smooth without using extra cement complet all as specified and as directed by the Engineer in charge Note :-WPC shall be measured & paid separately as supply only

M&L, 5mm thick rendering in CM 1:3 on fair faces of concrete surfaces as on ceilings/roof top and alike finished even and smooth without using extra cement complete.

Supply only integral liquid water proofing compound complete all as specified & as directed by Engineer-in-Charge.

Prepration of New external plastered wall surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :- (a) Applying 1mm thick wall care putty on wall surface and smoothening the surface prepatory to paint. (b) Applying 02 coats of exterior emulsion paint (light shade) with highlighter of any approved shade, @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed.

Prepration of New internal plastered wall/Ceiling surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :- (a) Applying 1.5 mm thick wall care putty on wall surface and smoothening the surface prepatory to paint. (b) Applying 02 coats of interior emulsion paint (light shade) @ 10 sq.m/litre/2 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed.

Supply only chicken wire mesh 22 gauge of size not less than 20X20mm all as specified & as directed by Engineer-in-Charge. Make : Swastik or equivalent as approved

Complete removal of existing treatment of any type/description from walls/RCC surfaces/ceiling/chajjas/roof projections etc with mechanical means/grinder complete all as specified.

M&L for preparation of existing treated surfaces on walls/ceilings and applying 01 coat of interior emulsion paint (light shade) @ 20 sq.m/litre/1 coat by using roller to wall/ceiling surfaces including filling wall putty in depressions, sand papering etc and making the surface smooth and applying a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed.

Preparation of existing treated surfaces and applying 01 coats of exterior emulsion paint (light shade) with highlighter of any existing shade, @ 10 sq.m/litre/1 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed.

Demolition concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) all as specified complete all as specified and directed by Engineer-in-Charge.

M&L for 40 mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) agg as in floor finishing cement concrete surface Finishing cement concrete surface even complete all as specified and directed by Engr in Charge . (Note : Concrete work to be laid in bays n exc 3.00 m length/width and laid in alternate ways, grroves should be filled with bitumen and sand in 1:3).

M&L for Cement concrete work in pavement/ hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less complete all as specified and directed by Engineer in Charge Note:- Metallic floor hardner is paid separately.

Supply only metallic floor hardner (as approved by GE) complete all as specified and directed

Forming 12 mm thick expansion joints filled with preformed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘B’ and provided with 20 mm diamild steel dowel bars 50cm long (25cm in each slab) with ferrules, spaced at 300 mm centres, including boring form work and preformed filler for dowels complete all as specified and directed by Engineer in Charge

S&F Steel rolling shutters 1.25mm MS lath (exc 25 sqm but not exc 30 sqm) , MS lath with all allied accessories as per IS: 6248:1979 Pull & Push Type painted with single coat Red oxide primer. Motorised systme for the shutter using Side Motors with built in Reduction Gear, Limit switches, starters etc and having chain operation system (to be used in case of Power Failure) complete all as specified and directed by Engineer in Charge. Note: Ball bearing, safety locks & Motorised system motor shall be measured &paid separately.

S & F for Safety lever locks mild steel with 4 levers for rolling shutters lockable from both inside and outside complete all as specified.

S&F for Ball bearing for rolling shutters complete all as specified and directed

S&F fixing Push type type motor for rolling shutter using side motor builtn in reduction gear , limit switches, starters etc of size exc 25 sqm but not exc 30 sqm. Complete all as specified and directed by Engr in Charge.

S&F Gypsum board false ceiling of size 600 x600 x12 cm thick for false ceiling panel or tiles for insulation and accoustic purposes, 60 cm x 60 cm in size laid/inserted to timber/GI/Aluminium framework with screws complete all as specified and directed by Engr-in-Charge.

S&F for Anodised aluminium snap grid frame work for false ceiling including hangers all as specified.

M&L for Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specfied and directed by Engineer in Charge

M & L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specfied and directed by Engineer in Charge

Supplying and laying of CPVC pipes of outer dia 20 mm SDR 11 & Plain CPVC SDR 11 inlcuding all fittings i.e.Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specified and directed by Engr in Charge.

Supplying and laying of CPVC pipes of outer dia 25 mm SDR 11 & Plain CPVC SDR 11 inlcuding all fittings i.e.Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specified and directed by Engr in Charge.

Supplying and laying of CPVC pipes of outer dia 32 mm SDR 11 & Plain CPVC SDR 11 inlcuding all fittings i.e.Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specified and directed by Engr in Charge.

S&F 1000 ltr Rotaional poly water storage tank cylinerical hoisted and fixed in posn all as specified in SSR Pt I and directed by Engr-in-charge.

S & F 20mm ball brass valve high pressure, with polythelene float and flynut complete, screwed to iron pipe.

M&L for reinforced cement concrete type B1 1:2:4 (20 mm graded aggregate) as in slab supported on walls, beam and column in floors, roofs, landings, balconies, deck slab, parapet walls and in shelves and etc and setting in mortar complete with joints to match complete all as specified and directed by engr in charge. Note : Rates of Demolition of RCC of any descrition are included

Formwork to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed by Engr in charge

M & L mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia

S&F 0.56 mm thick Plain, Aluminium sheeting, Alloy 31000 H4 for crumple/ expansion joints, ridges, hips, valley gutter, drip, and straight flashing (length and girth as fixed) fixed with self tapping screws complete all as specified and directed by Endineer -in -Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed by Engineer -in-Charge.

M&L PCC 1:3:6, Type C2 using 40mm graded stone aggregate filling of post hole complete all as specified and directed by Engineer-in-Charge.

S & F for steel work in tubular trusses ,channels , including special shaped washer, plates nuts and bolts, gusset plates, including necessary drilling etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed by Endineer -in -Charge.

M&L Preparation of new steel primed surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified

S & F for Flat iron for wind ties, plates (plain or chequered) channels, posts, square cut or notched (ordinary and counter sunk) forming holes etc Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed by Endineer -in -Charge.

S&F mild steel screw bolts (machine made) with hexagonal or square head at one end, and screwed the other,or screwed both end to be fitted with washer and one hexagonal/ square nut not exceeding 5cm long and dia of neck 11 to 15mm complete all as specified and directed by Engineer-in-Charge.

Dismantling framed trusses not exc 10 m span complete all as specified and directed by Engineer in Charge

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Endineer -in -Charge.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Endineer -in -Charge.

Taking down steel windows/ventilators complete all as specified and directed by Endineer -in -Charge.

Taking down shutters of any description and type exc 1 Sqm but n exc 2 sqm each and refixing in same opening after resecuring easing duly completed repair work items in all respects etc.complete all as specified and directed by Engineer - in - Charge.

Taking down shutters of any material and descriptionand type n exc 1 Sqm each and refixing in same opening after resecuring easing duly completed repair work in all respects etc.complete all as specified and directed by Engineer - in - Charge.

Taking down wooden chowkats or frames (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 sqm each complete all as specified and directed by Engineer in Charge

Taking down wooden/FRP/PVC chowkats or frames (without taking off shutters from the frame) not exceeding 1.5 sqm each complete all as specified and directed by Engineer in Charge

S & F Factory made laminated single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of but of Frame size 65x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall not be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made 30 mm thick 100 % solid WPC (Wood Polymer Composite) Laminated Flush Door size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: Rates are included of 125 mm SS hinges with stainless steel screws (03 Nos ), 200 mm long Stainless steel tower bolt (02 Nos) and 300mm long Stainless steel sliding bolt (01/02 Nos) & Stainless steel handles (02 Nos).

S&F Factory 30 mm thick 100 % solid WPC (Wood Polymer Composite) Laminated Wiremesh shutter of size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant for fixing Mosquito wire mesh SS-304 Grade (Not to be paid as separate item) and XPM (25mmx25mm diagnoal) aluminium powder coated mesh combine in panel area of door except stiles and rails to be paneled wire mesh with self tapping round headed screws at required distance screws and edge covered with feathered PVC edge beading all around mesh and fixing stainless stell butt hinges of required size with necessary full body threaded star headed countersunk SS Screws, all as per direction of Engineer-In-Charge. Note: Rates are included of stainless steel wire meash, 125 mm SS hinges with stainless steel screws (03 Nos ), 200 mm long Stainless steel tower bolt (02 Nos) and 300mm long Stainless steel sliding bolt (01/02 Nos),Stainless steel handles (02 Nos))

S & F Factory made laminated single extruded WPC (Wood Polymer Composite) 100 % solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of but of Frame size 75 x 50 mm(moulded) single rebated, made from wood polymer composite (single extruded process) material comprising of virgin PVC polymer of K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 780 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be not paid for separately) Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S & F Factory made laminated single extruded WPC (Wood Polymer Composite) 100% solid plain flush door shutter of 24 mm thick size comprising of virgin polymer of K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: 125 mm long stainless steel butt hinges (03 nos), 150 mm long aluminium handles (02 Nos) and 150 mm long aluminium tower bolts shall not be paid separately)

S&F in repair for door closer hydraulically regulated, alunimiun body designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed by Engineer-in-Charge.

M & L for 75mm thick cement concrete type C-1, 1:3:6 using 20mm graged aggregate as in plinth protection complete all as specified and directed by Engineer - in - Charge.

Demolition of brick work built in cement mortar of any description complete all as specified and directed by Engineer - in - Charge.

M&L for brick work with sub class 'B' bricks (old size) straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed by Engineer - in - Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick sorrounds, glazed with oil putty or fixed with beads.

S&F min 5mm thick toughned glass plain n. exc 0.5 sqm in each plane all as specified and directed by Engr-in-Charge.

Supply & Fix 4mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in suqares n.exc 0.5 Sqm in each pane

M&L two coat of synthetic enamel paint on old painted surfaces of steel and iron work over 10 cm width or girth including preparation complete all as specified and directed by Endineer -in -Charge.

S&F wall hung WC with UF Seat Cover ,Hinges, Accessories Set Size 640 x 360 x 765 mm white complete, including concealed body flushing cistern with hinging arrangement, complete all as specified and directed by Engineer-in-Charge.

S&F Single lever Basin Mixer without Popup waste with 450 long Braided Hoses with long screwed for iron pipe of 15 mm dia, complete all as specified and directed by Engineer - in - Charge.

S&F in repairs 15mm bib taps cast copper alloy, chromium plated fancy type with crutch or butterfly handle screwed down screwed for Iron pipe or for brass ferrule and fixed complete all as specified and directed by Endineer -in -Charge.

S&F in repair 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Endineer -in -Charge.

S&F in repair 15 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Endineer -in -Charge.

Supply and fix in repairs chromium plated stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union complete all as specified and directed by Endineer -in -Charge.

S&F in repair concealed chromium plated Angle stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed by Engineer-in-Charge.

S&F Grating doom 100mm dia of CP (Minimum weight 25gms) complete all as specified and directed by Endineer -in -Charge.

S&F Soap dish CP brass 100mm dia (round or oval) fixed to walls or dados. complete all as specified and directed by Engineer - in - Charge.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm long complete all as specified and directed by Endineer -in -Charge.

Dismantling of cast iron or reinforced concrete drain pipes jointed in cement mortar and taking off our trenches/wall if required complete all as specified and directed by Endineer -in -Charge.

S&F 110mm bore uPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall with uPVC holding clamps/laid in trenches and including Demolition and breaking up or taking down PVC/AC/CI/SSW 100mm bore pipe drain pipes, set in cement mortar including PCC haunching and bedding, complete complete, complete all as specified and directed by Endineer -in -Charge.

S&F 110mm bore uPVC (SWR) bend/Tee, any radius with access door complete all as specified and directed by Endineer -in -Charge.

S&F 110mm bore uPVC (SWR) vent cowl complete all as specified and directed by Endineer -in -Charge.

S&F 110mm bore uPVC 'S/P' Trap complete all as specified and directed by Endineer -in -Charge.

S&F 75 mm bore uPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall with uPVC holding clamps/laid in trenches and including Demolition and breaking up or taking down PVC/AC/CI/SSW 100mm bore pipe drain pipes, set in cement mortar including PCC haunching and bedding, complete all as specified and directed by Endineer -in -Charge.

S&F 75 mm bore uPVC (SWR) bend/Tee, any radius with access door complete all as specified and directed by Endineer -in -Charge.

S&F 75 mm bore uPVC(SWR) vent cowl complete all as specified and directed by Endineer -in -Charge.

Supply and fixing stainless steel drapery curtain rod 25mm dia, fancy type, fabricated out of anodised aluminium alloy sheet not less than 20 guage, including brackets and pair of decorated end knobs (finials), stop roller etc, pretreated powder coated natural color complete (size of each curtain not less than 1.20m) all as specified & directed by Engineer-in- charge.

S&F sinks with drainage board made of stainless steel 1 mm thick for kitchen with plugs, washers and waste coupling 40mm bore dia of discharge pipe , waste pipe plain 90cm long suitable for sink waste coupling, waste jali including making grooves , fixing properly or bedding in cement mortar to walll or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer - in - Charge.

S&F stainless steel plate rack 600x750x250 mm thickness of sheet 1 mm thick complete all as specified and directed by Engineer - in - Charge.

S&F in repair 18mm thick high Density High Moisture Resistant (HDHMR) exterior Grade Board with both side white balancing (BSB) with density of 850 Kg/cu.m for frame and shutter for kitchen cabinets/Cupboards etc complete all as specified and directed. Note : (i) Board on back side wall will be fixed with minimum 5mm PVC spacers. The payment for the same deemed to be included in the quoted unit rates. (ii) Rates of following items are included : (i) Auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree. (ii) Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs. (iii) Tower bolts 250mm long of stainless steel 304 finished/of outer plate metal matt finished. (iv) D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 200mm long matt finished. (v) Butt hinges of size 75mm of stainless steel 202 Grade finished/of outer plate metal. (vi) Piano/continuous hinge of size 19 mm stainless steel complete all as specified.

S & F in repairs of Partial overlay / fully overlay hydraulic self closing concealed hinges having size 103mm x 64mm finish of nickel/silver complete all as specified and directed by Engr-in-charge.

S & F in repairs of stainless steel cabinet / drawers handle having a length of 250mm and shape complete all as specified and directed.

S & F in repairs of stainless steel modular thali-plate basket SS 304, size of 520x485x200mm,heavy duty and grade steelwith finish of zinc, corrosion resistance telescopic drawer channel having weighing capacity of 25 kg complete all as specified and directed.

S & F in repairs of stainless steel modular perforated cutlery basket SS 304 size of 52 x 48.5 x 10 cm with heavy duty and grade steelwith finish of zinc, corrosion resistance telescopic drawer channel having weighing capacity of 25 kg complete all as specified and directed.

S & F in repairs of stainless steel glass tray plate tray having length of 610mm, corrosion resistance telescopic drawer channel complete all as specified and directed.

S & F in repairs of stainless steel triple cutlery inserts having length of 500mm with telescopic drawer channel having weighing capacity of 6 kg complete all as specified and directed.

S & F in repairs of stainless steel hanging spice rack having three shelf spaces length of 500mm complete all as specified and directed.

S & F in repairs of stainless steel grain trolley SS 304 having size of 525x485x350mm, with heavy duty and grade steelwith finish of zinc, corrosion resistance telescopic drawer channel having weighing capacity of 25 kg complete all as specified and directed.

S & F in repairs of stainless steel slim Ergo single square rail 550mm anthracite finish with heavy duty and grade steelwith finish of zinc, corrosion resistance telescopic drawer channel having weighing capacity of 25 kg complete all as specified and directed.

M & L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles and including 15mm thick screed in CM 1:6 complete all as specified and directed by Engineer - in - Charge.

M&L 600mmx300mmx7-8 mm thick Premium (1st qulaity) straight edges, glazed ceramic coloured tiles as in vertical sufaces such as skirting or dado set & jointed in neat cement slurry & pointed in matching coloured polymer based grout to match the shade of tiles including 10mm backing coat in CM 1:4. Rates of dismantling are included.

M & L Green Marble work 14 to 16mm thick of size not less than 600mmx900mm thick (table rubbed and polished) in steps, jambs, pillars, in window cills, cooking platforms, in floors and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Green Marble including 15mm of screed bed in CM 1:6 complete. Note : 100mm wide white white marble strip of 16-20mm thick to be laid in design directed by Engineer-in-Charge.

M & L for Mirror polishing on marble/ granite/Kota stone/ stone work where ever required to give high gloss finish complete

M&L for Double charged Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed in CM 1:6 complete all as specified and directed by Engineer-in-Charge. Rates of dismantling are included.

M&L granite (of any type) work 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, hand wash platform and like laid over and including 12 mm thick cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge.

M & L for 40mm thick cement concrete type B-1, 1:2:4 using 20mm graged aggregate as in flooring , finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L 25mm thick cement concrete flooring type B1, 1:2:4 using 20.0 mm graded aggregate finished even and to receive interlocking tile/floor tiles / sand cushioning complete all as specified and directed by Engineer - in - Charge.

M&L75 mm thick cement concrete type D2, 1:4:8 (Using 40mm graded stone aggregate) filling sub base as in floors, paving, sub floor etc finished even and smooth complete all as specified and directed by Engineer - in - Charge.

M&L for sand filling (25mm thick) under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer - in - Charge.

M&L Machine pressed precast rubber moulded concrete coloured interlocking paver block any shape and size confirming to IS 15468-2006 of 60 mm thickness with grey cement and pigment M-35 Grade 20mm graded stone aggregate) complete all as specified and directed by Engineer - in - Charge.

M&L providing precast cement concrete in PCC (1:2:4) type B-1 with 20 mm graded aggregate for kerb stone and similar works with plain fair finishes including chamfers, weatherings, throat- ing etc. and setting in mortar (1:4) complete with joints to match complete all as specified and directed by Engineer - in - Charge.

M&L Coloured 60 cm x 60 cm x 20 mm thick Non skid (Hi Traffic grip tiles) set jointed and pointed in neat cement slurry in floors over 20mm of screed bed in CM 1:4 including coping at edges in PCC Type B1 (1:2:4) ( rates of dismantling of stone slabs and tiles are included complete all as specified and directed by Engineer in Charge.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Taking down eaves gutters and rainwater pipes,PVC (SWR) pipes ( any size or pattern ) including all fittings heads ,shoes, bends, and removal to store.

M&L two coat of synthetic enamel paint on old painted surfaces of wood and wood based materials over 10 cm width or girth including preparation complete.

Taking down carefully aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators) and making good the disturbed surfaces of wall, floors, ceiling in CM 1:3 etc complete all as specified and directed by Engineer - in - Charge.

Taking down existing tube light/ mirror light/ building light etc of any type/make/capacity from building/ rooms including testing serviceability complete all as specified and directed by Engineer - in - Charge.

Fixing only LED lights fitting 1x20/25W, 220V, LED tube light/securirty light/bulk head/mirror light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer - in - Charge.

M & L for concealed conduit point wiring complete for light/ fan on independent /combine board with cable 2.5 sqmm (Nominal area) FRLSH PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for modular metal flush boxes suitable length and Min 1.6 mm thickness, Min 51 mm depth for mounting, switches, sockets,fan regulator with modular cover plate with frame and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 2.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced by the Engineer in charge.

All as per Srl item No 116 here in before but for one switch socket combination 5/6 amp on independent board complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No 116 here in before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No 116 here in before but for one switch socket combination 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed by Engineer - in - Charge.

S & F in replacement modular switch 5/6 Amps single pole one way,one module including modular cover plate with frame and metal flush box complete all as specified and directed by Engineer - in - Charge.

S&F in replacement of module switch 1 way 16 A, 1 module complete all as specified and directed by Engineer - in - Charge.

S&F in replacement of modular socket, 6 Amps, 2/3 pin combined 2 module complete all as specified and directed by Engineer - in - Charge.

S&F in replacement of modular socket, 16 Amps, 2/3 pin combined 2 module complete all as specified and directed by Engineer - in - Charge.

Supply and fix in replacement industrial socket metal clad plug and socket with MCBs single pole 20 Amp complte all as specified and directed by Engineer - in - Charge.

S & F in replacement modular stepped type, fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in - Charge

Taking down fan, ceiling cable end, dismantling blades and removing fan and blades to store complete all as specified and directed by Engineer - in - Charge.

Taking down existing exhaust fan 450mm sweep, 240 volts and refixing the same after cleaning and servicing complete all as specified and directed by Engineer - in - Charge.

S&F Heavy duty metal body exahust fan of 450mm sweep ,240 volt,copper winding, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to distubed wall in cement mortar (1 :4) white washing matching with existing colour etc.

S & F in replacement ceiling rose surface bakelite three terminals complete all as specified and directed by Engineer - in - Charge.

S & F in replacement of existing light fitting with LED batten 20W LED batten with 'Eye Soft' technology & glarefree diffuser for perfect application in modern homes or aliminium housing and integrated electronic driver, 20 watt having input voltage AC140-300V, 50 Hz , 6500K, and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge.

S&F in replacement recess mounting 2 X 2 feet 36 watt LED luminaire with powder coated CRCA housing with LEDs,seamless front frame with high transmission acrylic cover and fixed electronic driver (surge protector) complete all as specified and directed by Engineer - in - Charge.

S&F decorative, wall mounting, made of polycarbonate body suitable for 9W LED lamp B-22 base complete all as specified and directed by Engineer - in - Charge.

S&F in replacement security light fitting LED TYPE 25 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge

S & F in replacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge

S&F LED lamp 9W for angle holder complete all as specified and directed by Engineer - in - Charge.

S&F wall mounted fan 400mm sweep, 240 volts complete all as specified and directed by Engineer - in - Charge.

S & F of sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in and including steel dia 25mm “medium quality” conduit including 6.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge.

Supply, fixing ,testing & commisioning of electric chimney (120 CM) with feature of baffle filter, inbuilit light, touch screen control panel, noise level, 58 dB, stainless steel body, air suction capacity 1200 CMH, speed level 3 , motor power 180 watt, input vol 220-240 V/50Hz, remote controlled and fitting in wall as connecaled or duct all as specified and directed by Eng-in-Charge.

S&F in replacement Sheet metal enclouser for doble door Vertical DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting VTPN 4 Way 415 Volt ISI marked 250Amps busbar stove enameled dust and vermin proof,IP:43 protection suitable for incorporation FP MCCB(V-Tech) N3 Frame upto 250A ,Isolators and including give connection with wire and cable etc complete all as specified and directed by Engineer-in-Charge.

S&F in replacement MCCB 4 pole 63 Amps with breaking capcity 16kA ,4 pole, Fixed TM and 415 volts AC Supply ISI marked complete all as specified and directed by Engineer - in - Charge.

S & F in repairs sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 12 ways, 240 Volts, ISI marked, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F in repairs sheet metal enclosure for double door DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SPN 8 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F in replacement MCB ‘B’ series type suitable for 240 volts,10 KA, AC supply 6-32 Amps , single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in repairs MCB ‘C’ series type suitable for 240 volts, AC supply 32 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

M & L for Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GI and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil ,returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electric plate no.3 of SSR part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on completion all as specified and directed by Engr -In - Charge

Supply, fix and install room window type air conditioner electric driven, single phase, cooling capacity 6000 K Cal per hour (2 Ton), BEE 5 star rated complte all as specified.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 160 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA complete all as specified.

Please Enable Macros to View BoQ information