Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹1.1 CrAccepted-AOC BARANGABARI CITY TOWN HELEM P O BARANGABARI P S HELEM DIST SONITPUR PIN 784172 | BISWANATH | ASSAM | 784172 | ₹1.1 Cr | L1 | Accepted-AOC AWARDED |
| 2 | L2₹1.1 CrRejected-AOC BARANGABARI CITY TOWN HELEM P O BARANGABARI P S HELEM DIST SONITPUR PIN 784172 | BISWANATH | ASSAM | 784172 | ₹1.1 Cr | L2 | Rejected-AOC NOT AWARDED |
| Sl No | Description | Qty | Unit | LALIT KUMAR AGARWALA L2 | M/S UDAARSIL CONSTRUCTIONS PVT. LTD. L1 |
|---|---|---|---|---|---|
| 1.00 | Collegeguri to Milan Nagar Road
Heavy dressing of the existing road including dressing high spots and filling low spots, cambering, watering, rolling with 8 to 10 tonne roller to obtain a specified compaction etc. to obtain a uniform formation surface with cross fall from the road centre line to the outer shoulder edge with allowance, made for required quantity of shoulder materials to remain in place to contain the new gravel layer. Works to be carried out in accordance with Technical Specification and as directed by the Engineer. | 600 | sq.m. | 3.08 ₹1,849.80 | 2.08 ₹1,249.80 |
| 2.00 | WBM Grading 3:
Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.
(A) By Manual Means | 40.4 | cu.m. | 5,775.32 ₹2.3 L | 4,775.32 ₹1.9 L |
| 3.00 | Providing and laying interlocking concrete block pavement with M40 grade grade of concrete blocks having thickness 80mm as per technical specification clause 1504 complete including carriage
Including Edge block/ Edge restraints | 540 | sq.m. | 1,222.73 ₹6.6 L | 1,222.73 ₹6.6 L |
| 4.00 | Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 | 1 | Nos. | 26,164.53 ₹26,164.53 | 26,164.53 ₹26,164.53 |
| 5.00 | Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. I Ordinary soil,A Manual Means,(I) Without dewatering,(i)upto 3 m depth | 179.93 | Cum | 134.47 ₹24,194.92 | 134.47 ₹24,194.92 |
| 6.00 | Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork.(N) Without plasticiser, A PCC Grade M-15 | 27.74 | Cum | 6,207.16 ₹1.7 L | 6,207.16 ₹1.7 L |
| 7.00 | Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork.(N) Without plasticiser, A PCC Grade M-20 | 5.33 | Cum | 7,018.14 ₹37,371.62 | 7,018.14 ₹37,371.62 |
| 8.00 | Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork.(N) Without plasticiser, C RCC Grade M-20 | 12.12 | Cum | 7,448.45 ₹90,275.19 | 7,448.45 ₹90,275.19 |
| 9.00 | Supplying, fitting and placing TMT bar reinforcement in open foundation complete as per drawing and technical specifications clause 1000 and 1202 | 0.27 | MT | 66,924.41 ₹17,868.82 | 66,924.41 ₹17,868.82 |
| 10.00 | Plain/Reinforced cement concrete, in sub-structure complete as per drawing and technical specification including steel shuttering formwork.(N) Without plasticiser, A PCC Grade M-15 | 40.37 | Cum | 6,565.23 ₹2.7 L | 6,565.23 ₹2.7 L |
Tender Value
₹1.1 Cr
EMD Value
₹2.3 L
Closing Date
8 Jan 2026, 2:00 pmClosed
Chief Engineer,PWRD
O/o the Chief Engineer PWRD,Assam,Guwahati-03
R and R of 1) Collegeguri to Milan Nagar 2)Jotte Balijan with protection work 3)Jalukbari Itapara with protection work 4)Tetonbari to Bahboria Gaon via Ghoroi mari gaon 5 Mornoiguri Kalmouguri 6) Mornoiguri PWD to Singarajan NDRF(PDNA-2022) 25-26
2025_PWD_49668_21
CE/Commn/192/2025-26/9
Open Tender
Civil Works – Roads
60 days
Biswanath
Please refer Tender documents.
4 documents required · 4 mandatory
₹2,270
₹2.3 L
Yes
O/o the Chief Engineer PWRD,Assam,Guwahati-03
10 Mar 2026
29 Dec 2025
8 Jan 2026
29 Dec 2025
8 Jan 2026
29 Dec 2025
29 Dec 2025 - 8 Jan 2026
2 Jan 2026
Collegeguri to Milan Nagar Road Heavy dressing of the existing road including dressing high spots and filling low spots, cambering, watering, rolling with 8 to 10 tonne roller to obtain a specified compaction etc. to obtain a uniform formation surface with cross fall from the road centre line to the outer shoulder edge with allowance, made for required quantity of shoulder materials to remain in place to contain the new gravel layer. Works to be carried out in accordance with Technical Specification and as directed by the Engineer.
WBM Grading 3: Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. (A) By Manual Means
Providing and laying interlocking concrete block pavement with M40 grade grade of concrete blocks having thickness 80mm as per technical specification clause 1504 complete including carriage Including Edge block/ Edge restraints
Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1
Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. I Ordinary soil,A Manual Means,(I) Without dewatering,(i)upto 3 m depth
Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork.(N) Without plasticiser, A PCC Grade M-15
Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork.(N) Without plasticiser, A PCC Grade M-20
Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork.(N) Without plasticiser, C RCC Grade M-20
Supplying, fitting and placing TMT bar reinforcement in open foundation complete as per drawing and technical specifications clause 1000 and 1202
Plain/Reinforced cement concrete, in sub-structure complete as per drawing and technical specification including steel shuttering formwork.(N) Without plasticiser, A PCC Grade M-15
Supplying, fitting and placing TMT bar reinforcement in sub-structure complete as per drawing and technical specifications clauses 1002,1005,1010 &1202.
Plain/Reinforced cement concrete, in sub structure complete as per drawing and technical specification and steel shuttering formwork (N) Without plasticiser, E RCC Grade M-20, a) Height upto 5 m,Case-I
Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications Cl. 800 and 1206.3,B. Natural gravel
Providing Pressure relief pipes 100 mm dia. In bottom slab of box cell on a filter media base of 500x 500 mm as per drawing and technical specfication clause 1205.5.7
Providing and Laying Curtain wall complete as per drawing and Technical specification clause 1304, B) Cement Concrete Grade M-15
Flexible Apron :Construction of flexible apron 1 m thick comprising of loose stone boulders weighing not less than 40 kg beyond curtain wall.
Construction of RCC railing of M30 Grade in-situ with 20 mm nominal size aggregate, true to line and grade, tolurence of vertical RCC post not to exceed 1 in 500, centre to centre spacing between vertical post not to exceed 2000 mm, leaving adequat space between vertical posts for expansion, complete as per approved drawings and technical specifications.
Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification , 'II -Sandy material
Providing weep holes in brick/stone masonry abutment and return wall complete
(2)Jotte Balijan Road with protection work Heavy dressing of the existing road including dressing high spots and filling low spots, cambering, watering, rolling with 8 to 10 tonne roller to obtain a specified compaction etc. to obtain a uniform formation surface with cross fall from the road centre line to the outer shoulder edge with allowance, made for required quantity of shoulder materials to remain in place to contain the new gravel layer. Works to be carried out in accordance with Technical Specification and as directed by the Engineer.
Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 (ii) From Private Land
Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (ii) From Private Land
Construction of granular surface course by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three wheel 80-100 kN static roller capacity to achieve the desired density, complete as per Technical Specification Clause 402
Direction and Place Identification signs upto 0.9 sqm size board Providing and erecting direction and place identification retro reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701
Providing and laying boulder apron laid in wire crates for bed protection with stone boulder of minimum size and weight as per table 1300.1 no fragment weighing not less than 25kg. laid dry complete as per drawing and technical specification clause 1301
3)Jalukbari Itapara Road with protection work Heavy dressing of the existing road including dressing high spots and filling low spots, cambering, watering, rolling with 8 to 10 tonne roller to obtain a specified compaction etc. to obtain a uniform formation surface with cross fall from the road centre line to the outer shoulder edge with allowance, made for required quantity of shoulder materials to remain in place to contain the new gravel layer. Works to be carried out in accordance with Technical Specification and as directed by the Engineer.
Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 (ii) From Private Land
Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (ii) From Private Land
Construction of granular surface course by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three wheel 80-100 kN static roller capacity to achieve the desired density, complete as per Technical Specification Clause 402
Direction and Place Identification signs upto 0.9 sqm size board Providing and erecting direction and place identification retro reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701
Providing and laying boulder apron laid in wire crates for bed protection with stone boulder of minimum size and weight as per table 1300.1 no fragment weighing not less than 25kg. laid dry complete as per drawing and technical specification clause 1301
Excavation for structures :- E/W in excavation for structures as per drawing and Technical specification Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and deleterious materials and disposal upto a lead of 50 I. ordinary Soil (A) Manual means (i) Depth up to 3.00m
Providing concrete for plain/ reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203(1:3:6) (I) PCC M10
Beeding of Pipe (ii) Type B(First Class beeding) Laying First Class Beeding on well compacted sand, moorum or approved granular materials
Providing concrete for plain/reinforced concrete in open foundation complete as per drawing & technical specifications. A. with crushed stone III.PCC M-20 grade (1:2:4) Hand mixed.
Providing & Laying reinforced cement concrete pipe NP-3 for culverts on 1st class bedding of granular material in single row including fixing coller with cement morter 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works.1000mm dia
4)Tetonbari to Bahboria gaon via Ghoroi mari gaon with protection work Heavy dressing of the existing road including dressing high spots and filling low spots, cambering, watering, rolling with 8 to 10 tonne roller to obtain a specified compaction etc. to obtain a uniform formation surface with cross fall from the road centre line to the outer shoulder edge with allowance, made for required quantity of shoulder materials to remain in place to contain the new gravel layer. Works to be carried out in accordance with Technical Specification and as directed by the Engineer.
Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 (ii) From Private Land
Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (ii) From Private Land
Construction of granular surface course by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three wheel 80-100 kN static roller capacity to achieve the desired density, complete as per Technical Specification Clause 402
Direction and Place Identification signs upto 0.9 sqm size board Providing and erecting direction and place identification retro reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701
Providing and laying boulder apron laid in wire crates for bed protection with stone boulder of minimum size and weight as per table 1300.1 no fragment weighing not less than 25kg. laid dry complete as per drawing and technical specification clause 1301
Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out,construction of shoring and bracing ,construction of shoring and bracing removal of stumps and other deleterious material and disposal upto a lead of 50 m ,dressing of sides and bottom and backfilling in trenches with excavated suitable material
Providing concrete for plain /reinforced concrete in open foundations complete as per drawingsand technical specifications Clause 802,803,1202 &1203 with natural soil (ii) P.C.C grade M 15. Nominal mix 1:2.5:5
Providing concrete for plain /reinforced concrete in open foundations complete as per drawingsand technical specifications Clause 802,803,1202 &1203 Pcc m 20
Plain / reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802,804 ,805 ,806,807,1202 and 1204 (III) RCC Grade M20. (i) for height upto 5 m
Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202
Reinforced Cement Concrete M 25 grade approach slab including reinforcement and formwork complete as per drawing and technical specifications Clauses 800 and 1211
Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206 .3 With crushed stone
Drainage spouts complete as per drawing and technical specifications Clause 1209
Backfilling behind abutment ,wing wall and return wall complete as per drawings & technical specification Clause 1204 .3.8
Providing weepholes in brick masonry / stone masonry ,plain / reinforced concrete abutment wing wall ,return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1 ( V ) :20 ( H ) towards drawing face complete as per drawing and technical specification Clauses 614 ,709 ,1204 .3.7
Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment ,wing wall ,return wall to the full height ,compacted to firm condition complete as per drawing and technical specification Clause 1204 .3.8
Construction of R.C.C. railing of M 25 grade in cast-in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical railing post not to exceed 1 in 500, centre-to-centre spacing between vertical posts not to exceed 2000 mm as per drawing and technical specifications Clauses 800, 900 and 1208.3
Providing and fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing and technical specifications
5)Mornoiguri to Kolmouguri Road with Protection Work Providing and laying boulder apron laid in wire crates for bed protection with stone boulder of minimum size and weight as per table 1300.1 no fragment weighing not less than 25kg. laid dry complete as per drawing and technical specification clause 1301
Providing and laying boulder apron laid in wire crates for bed protection with stone boulder of minimum size and weight as per table 1300.1 no fragment weighing not less than 25kg. laid dry complete as per drawing and technical specification clause 1301
Please Enable Macros to View BoQ information
stage.html
html • 0.04 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 2.76 MB
Tendernotice_2.pdf
PDF • 8.23 MB
Tendernotice_3.pdf
PDF • 0.56 MB
BOQ_78980.xls
BOQ • 1.38 MB
Download all tender documents and submit your bid