Providing Illumination of the Heritage Structures of Viper Island SW SITC of 01 No 1000 LPH RO Plant i/c Internal Electrical Connection of Motors and Switch Gears and IEI Works of RO Plant Bldgs at Viper Island Electrical Part Only SH Providing IEI

Amount

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. a) Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

b) 4X 6 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Supplying and fixing metal box of 150 mm X 75 mm X 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch, connections, painting etc. as required

Supplying and fixing metal box of 180 mm X 100 mm X 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 A & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing brass batten/ angle holder including connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required a) Single Pole

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required a) 40 Amps

Supplying and fixing following way, single pole and neutral, sheet steel, 4 way MCB Double Door distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as Equivalent to Havells DHDPSHODRW04 or its equivalent.

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) a) 4 way (4 + 12), Double Door

Supplying and fixing following rating MCB D-series High inductive load and high inductive current breaker 4-pole,63 Amps, 415 Volts similar to C&S Cat Id No:CSMBS4D63 or its equivalent to ISI standars.

Supplying and fixing following rating MCB D-series High inductive load and high inductive current breaker 4-pole,50 Amps, 415 Volts similar to C&S Cat Id No:CSMBS4D50 or its equivalent to ISI standars.

Supplying of following XLPE insulated heavy duty armoured aluminum conductor UG cable of 1.1 KV grade conforming to IS 7098 (Part-I) and IS No:1554 (Part-I 1988 as applicable Make: Clooster/ Havells/ Polycab etc as reqd. a) 25 sqmm x 3.5 core

Supplying and laying of one number double walled corrugated high density Polythylene pipe having corrugation on the outer wall and plain surface inner wall confirming to IS 14930 Part -I complete with necessary HDPE fitting for protection of 1.1 KV grade underground cable directly in ground at the depth of 50 cm in the existing cable trench etc as reqd. a) 77 mm outer dia x 63 mm inner dia

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL pipe as required. a) Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing masonry open duct as required. (a) Upto 35 sq. mm

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required a) 3 1/2 x 25 sq.mm

Providing earthing with safe earthing electrode of galvanization 80 to 100 microns, length 2000mm, outer dia 50 mm, inner dia 19 mm and inner space be filled with crystalline conductive mixture including filling -up with electrolite (Back fill compound) as required for safe earth electrode and providing masonary enclosure with cover plate having locking arrangement etc. as required. (Ashlok)

Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Supplying of 20W LED CRCA batten with decorative end cap complete with retrofit Polycarbonate /glass Tube as equivalent to C&S TARA-M/20W order No. LTDC01220WLED/WD or its equivalent including replacement of existing conventional light.

Supplying of A.C Ceiling fan (1200 mm) sweep without regulator i/c wiring down rod of standard length (upto 30 cm) with all accessories etc as required. Similar to make Havells Code Name ES50 Premium 5 (ISI Marked) or its equivalent etc., as required.

Supplying of 15 w LED lamp directly fitted in button holder as equivalent to C&S CHANDRA/15W/W order code LTHPEDLAMP15W/B22 or its equivalent etc., as required.

DAYAL HALDER