PROVN OF BATH ROOM AND TOILET BLOCK FOR FD WKSP COY AT ALONG MIL STN UNDER GE 872 EWS

Amount

EARTH WORKS (FOR BOTH B/R & E/M SERVICES)

Excavation Over Areas, not exc 1.50 Metre in depth and getting out in Soft /Loose Soil, complete all as specified and as directed.

Excavation Over Areas, exc 1.50 Metre but not exc. 3.00 Metre in depth and getting out in Soft /Loose Soil, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Removing Excavated Materials (Soils) not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point, complete all as specified and as directed.

Excavating in Trenches, not exc. 1.50 Metre Wide and Depth not exc. 1.50 Metre for Laying of Cables, Pipe Line, etc., Forming Surfaces to required Foundation, etc. and getting out in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, providing Heaps along the Route of the Cables, Pipe Line, etc., with Surplus Soil (if any) in Soft/Loose Soil, complete all as specified and as directed.

BUILDING SERVICES/WORKS

M&L Hardcore broken Stone or Boulders, gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and well rammed to a True surface, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) in Foundation, Filling and Mass Concrete, etc. including necessary Formwork as ordered, complete all as specified and as directed.

M&L Pre-cast Cement Concrete 1:3:6 (20mm graded stone aggregate) Block Masonry with Solid Blocks, exc. 10 Cm in width, Set in Cement Mortar 1:4, complete all as specified and as directed.

M&L Damp Proof Course 40mm thick in Cement Concrete 1:2:4 (12.5mm graded stone aggregate) to Horizotal/Vertical Surface and Applying Evenly a coat of Blown type Bitumen at the rate of 1.50 Kg per Square Metre and blinding with Clean Dry Sand @ 0.05 Cum per Square Metre including necessary Formwork, complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50x47mm made out of 5.0mm thick Plain Colour PVC Sheet reinforced with Mild Steel Square Tube and fixing in Opening as per Specification and Drawing of MES Schedule, complete all as specified and as directed.

S&F Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) consisting of Frame made out of Mild Steel Tubes for Top & Bottom Rails, Mild Steel Frame shall be covered with heat moulded plain color PVC ‘C’ Channel having a PVC Strip of 20mm width stuck inside with Solvent Cement for Stiles & Plain color PVC Sheets for Top Rail, Lock Rail & Bottom Rail on either side & gap insert for Top Rail & Bottom Rail, Paneling of plain color PVC sheet to be fitted in the Mild Steel Frame, welded/sealed to the Stiles & Rails with suitable PVC Sheet Beading & jointed together with Solvent Cement, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt, 125mm long, Extruded Section, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge 75mm in size (as approved) and fixing to PVC Door Shutters, complete all as specified and as directed.

S&F Aluminium Handle 125mm, Cast type, anodised, complete all as specified and as directed.

M&L Rolled Mild Steel in Main and Cross Beams, Hip and Jack Rafters, Purlin where connected to Common Rafters and Running Rails and Guides for Sliding Doors, fixed with Angle Cleats or Other Connecting Plates, conforming Fe-290 (Gde E165), complete all as specified and as directed.

S&F Corrugated Mild Steel Sheeting 0.63mm thick, Galvanised @ 275 Gram Per Sqm, with Two Corrugation Side Lap in Roofs, Walls, etc., fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Floors, etc., complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 100mm thick in Sub-base to Floors, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 40mm thick in Base of Flooring, etc., finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 100mm thick in Hardstanding, etc., laid in Alternate Slab/ Panel, finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) 75mm thick in Plinth Protection, etc., laid in Alternate Slab/ Panel, finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Tiles 7.0-8.0mm thick (square/rectangular) area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality) conforming to IS:13755, in Floors, jointed in Neat Cement Slurry and pointed in Coloured Cement to match the Tile, laid over and including Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Glazed Ceramic Coloured Tiles 300x200x7.0mm thick (1st quality) in Vertical Surfaces i.e. Dado, Skirting, etc, set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Rendering 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (External) 15mm thick in Cement Mortar 1:4 on Brick/PCC Blocks or Concrete Works including mixed with WPC, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid saperately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Oil Bound Distemper over a Coat of Chalk Whiting as preparatory to distempering, complete all as specified and as directed.

M&L Preparing New Steel and Iron Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type, long Shank and Cup (Concealed) with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and as directed.

S&F Stop Cock/Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions, complete all as specified and as directed.

S&F Angle Stop Valve of PTMT 15mm bore (dia) having minimum Weight 90 Grams, any Colour, high pressure screwed for Iron Pipe, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule, complete all as specified and as directed.

S&F PTMT Ball Valve 20mm bore (dia), having weight not less than 210 Grams, high pressure with Epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe, complete all as specified and as directed.

M&L Vitreous China White Squatting Pan of size 580x440mm, Orissa Pattern with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) incluiding provision of Lime Concrete Bedding and Making Good to Floor/distrubed surfaces, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float and Handle, a Pair of Cast Iron Brackets Erecting Stand duly Painted, including PVC Flush Pipe 32mm dia with PVC Long Bend, Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in size and 450mm in length with PTMT Nuts, complete all as specified and as directed.

S&F Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair), complete all as specified and as directed.

S&F Brass Chromium Plated Shower Rose of size 100mm with Swival Joint including fixing to Steel Pipe 15mm bore (dia), complete all as specified and as directed.

S&F Stainless Steel Soap Dish not less than 100mm in size (as approved), fixing to Walls with Screws, complete all as specified and as directed.

M&L Cast Iron Nahani Trap having dia of Outlet 50mm with Grating including jointing to Waste Pipe fixed in Cement Concrete 1:2:4 (20mm graded stone aggregate), complete all as specified and as directed.

S&F PVC (SWR) Pipe 75mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors, complete all as specified and as directed.

S&F PVC (SWR) Pipe 110mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors, complete all as specified and as directed.

S&F PVC (SWR) Pipe 110mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, fixed to Walls, etc., complete all as specified and as directed.

S&F PVC (SWR) Junction 110mm bore (dia), Single (Single T), Equal or Unequal, provided with Access Door, jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Vent Cowl 110mm bore (dia) etc., jointing with Solvent Cement, complete all as specified and as directed.

INTERNAL ELECTRIC SUPPLY

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE FAN POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 20/25mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. for ONE 5 PIN SOCKET POINT on SAME BOARD, controlled by One Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 6 PIN 6/16 AMP SOCKET OUTLET POINT on INDEPENDENT BOARD, controlled by One Switch 16 Amp, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 5 Pin, Flush type, Multi-purpose, 230 Volt AC Single Pole, 1-way suitable for Plug Top 2 Pin/ 3 Pin, 6 Amp and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6/16 Amp, 2-in-1 (3 Pin & 3 Pin), Flush type, Multi-purpose, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed.

S&F LED Bulk Head Fitting 1x10 Watt comprising of High Brightness LEDs, Enviroment Friendly, Ultra Modern, Energy Saving, Surface mounted and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable, complete all as specified and as directed.

S&F LED Tube Light Fitting 1x10 Watt with LED 10 Watt Tube, Wall mounted type with Aluminium Housing and Integrated Electronic Driver, complete with all Accessories, Pre-wired and connecting up with and including suitable size Twin Core Twisted Flexible Copper Conductor Cable, complete all as specified and as directed.

M&L Cutting Brick/PCC Block Walls and making Hole suitable for fixing Exhaust Fan, Making Good the disturbed Surfaces with and including Masonary and Plastering Work including providing Surface Treatment (Colour Washing/ Distempering/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed.

S&F Exhaust Fan 450mm Sweep 1400 RPM, heavy duty, Energy Efficient with Louvers, Single Phase, 50 Hz, 230/240 Volt, AC, connecting with and including 3 Core Twisted Cable of size 23/0.0076 from Fan to Ceiling Rose including Mild Steel Holdfast or Bolts, Nuts, etc., complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up, complete all as specified and as directed.

S&F MCB Single Pole & Neutral 40 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up, complete all as specified and as directed.

S&F Sheet Metal Enclosure SPN 8-way Distribution Board, Double Doors, 240 Volt AC, Painted with Epoxy Based Powder Coated Painting, suitable for mounting MCB DP/SPN as Incomer and MCB SP as Out-going, complete with 200 Amp rated Bus-bars, Neutral Bars & Earth Bar, Connecting Cable Link with Top and Bottom Removable Gland Plate, having IP-43 Protection and connecting up, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing, complete all as specified and as directed.

EXTERNAL ELECTRIC SUPPLY

Supply & Laying XLPE insulated, Armoured, Heavy duty Electric Cable with Aluminium Stranded Conductor, 1100 Volt grade, Cross-sectional area 10 Sqmm, 2 Core, laid in Trenches, Ducts or Passing through Pipes or Fixing on Poles, Walls, etc. including necesary Cable Lugs, Glands, Bolts, Nuts, Washers, etc., complete all as specified and as directed. NOTE : Necessary Earth works, Sand Cushioning, Cable Protection Cover, etc. will be Measured and Paid separately under relevent Items.

M&L Sand Cushioning (dry) in Trenches/Ducts for protection of UG Cables (below, above and around the UG Cable laid) of 23 Cm Spread thickness (8 Cm in depth before laying the Cable and 15 Cm in depth after laying the Cable) and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. NOTE : For the purpose of Payment, Punned thickness of Sand Cushioning only will be Measured.

Supply & Laying Unreinforced Pre-cast Concrete Cable Cover of size 300x180x40mm thick, Class LV, Type 2, Flat, Concrete grade M-20 minimum, complete all as specified and as directed.

EXTERNAL WATER SUPPLY

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, laying in Trenches, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Galvanised Steel Tubing 40mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, laying in Trenches, complete all as specified and as directed.

S&F Galvanised Steel Tubing 40mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, ISI marked, screwed both Ends for Iron Pipe, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 40mm bore (dia) with Iron Wheel Head, ISI marked, screwed both Ends for Iron Pipe, complete all as specified and as directed.

M&L Cutting Cast Iron/ GI Pipe of any size (dia) and Reducing to required length before laying and to existing Pipe Lines for taking up/making Branch Connection and Insertion of Specials, complete all as specified and as directed.

SEWAGE DISPOSAL

M&L Loose Filling with Broken Bricks Aggregates of gauge 80mm to 150mm in Soakage Pits, Soakage Wells, etc., complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) in Foundation, Filling and Mass Concrete, etc. including necessary Formwork as ordered, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (40mm graded stone aggregate) in Foundation, Filling and Mass Concrete, etc. including necessary Formwork as ordered, complete all as specified and as directed.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Foundation including Rafts, Footing, Foundation Beams for Column Basement Slab, under reamed Piles, complete all as specified and as directed. NOTE : Reinforcement and Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Columns, Pillars, Piers, Posts and Struts, etc., complete all as specified and as directed. NOTE : Reinforcement and Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Roof Beams, Lintel Bands, Cantilevers, Bressumers, Lintels over 1.50 Metre Span, etc., complete all as specified and as directed. NOTE : Reinforcement and Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Slabs supported on Walls, Beams and Columns in Floors, Roofs, Landings, Balconies, Canopies, Deck Slabs and in Shelves and the like, complete all as specified and as directed. NOTE : Reinforcement and Formwork will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Cement Concrete 1:2:4 (20mm graded stone aggregate) in Landings, Cover Slabs of Manhoes and Similar Articles with Plain Faces, etc., Set in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Cement Concrete 1:3:6 (20mm graded stone aggregate) Block Masonry with Solid Blocks, exc. 10 Cm in width, Set in Cement Mortar 1:6, complete all as specified and as directed.

M&L Pre-cast Cement Concrete 1:3:6 (20mm graded stone aggregate) Block Masonry with Solid Blocks in Honey Combing, exc. 10 Cm in width, Set in Cement Mortar 1:4, complete all as specified and as directed.

M&L Formwork to Sides of Concrete Foundations, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams and Similar Work; Square, rectangular or polygonal, Vertical or to batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides of Pillars, Posts, Struts, Piers, Columns and Stanchions, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Soffits of Suspended Slabs such as Roof Slabs, Floor Slabs, Landings and Similar Work; not exc. 200mm thick (Horizontal or Sloping), etc., Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Edges of Concrete Flats, Treads, Breaks in Floors, Window Cills, Concrete Railings, Openings in Concrete Walls, Floor and Roofs, not exc. 20 Cm Wide and Sides of RCC/ PCC Bands in Walls, Horizontal or Sloping and Similar Work, exc. 10 Cm but not exc. 20 Cm Wide, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L TMT Bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on Brick/PCC Blocks or Concrete Works including mixed with WPC, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid saperately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

S&F PVC (SWR) Pipe 75mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, fixed to Walls or laid in Floors, complete all as specified and as directed.

S&F PVC (SWR) Pipe 110mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, laid in Trenches, complete all as specified and as directed.

S&F PVC (SWR) Vent Cowl 75mm bore (dia) etc., jointing with Solvent Cement, complete all as specified and as directed.

M/S ARUNACHAL VIKASH

M/S GOLANG CONSTRUCTION CO.

M/S TSERING DHONDUP

M/S NAVA BHARAT BUILDERS

M/S P N ASSOCIATES

M/S CHANDAN ENTERPRISE

M/S A K BROTHERS

Construction House