PROPOSED CONSTRUCTION OF MULTIPURPOSE BUILDING AT CHINNAKAKADAI STREET BELONGS TO ARULMIGU ARUNACHALESWARAR THIRUKOVIL IN TIRUVANNAMALAI.

Amount

Earthwork excavation for Narrow Trenches in all soils and sub soils to full depth as may be directed except in hard rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary refilling the foundation with excavated earth other than sandy soil in layers of not more than 15 cm thick layers well rammed and depositing the surplus earth within compound in places shown by the departmental officers with an initial lead of 10 metre and initial lift of 2 metre and clearing and leveling the site etc., complete complying with standard specification and as directed by the departmental officers

Providing Pre Constructional Anti- Termie Treatment and Creating a chemical Emulsion of required concentration to Raft Slab and Beam, under cellular Raft Slab ,around the Footings,Column Pits, Trenches etc complete..

Supplying and Filling with M. Sand in Foundation and Basement of layers not more than 15 cm thick well rammed and consolidated including cost and conveyance of materiales and labour charges etc complete.

Supplying and Filling with Gravel in Foundation and Basement of layers not more than 15 cm thick well rammed and consolidated including cost and conveyance of materiales and labour charges etc complete.

Plain Cement Concrete 1 : 5 : 10 ( One Cement Five M.Sand Tend Broken Stone ) using 40mm ISS Hbg metal including cost conveyance of all materiales and labour charges etc coplete as per standard specification .

Supplying and Errecting ,Centering for Sides and Soffits including Supports and Strutting Upto 3.30 M Heigh with all Cross Bracing for Plane Surface using Mild Steel Sheets of 90 x 60 cm 10 G Stiffened with MS Angle of 25 x 25 x 3mm

For Column Footing,Plinth Beam, Grade Beam , Raft Slab,Bed Block etc

For Vertical surfaces such as Vertical Slab, Side Slabs of Boxing, Vertical Drops, Facia, Vertical Walls etc.

for Plane Surfaces such as Rectangular or Square RCC Columns, Sunshades, Top and Bottom Slab of RCC Boxing, etc.

For Plane surfaces such as RCC Floor Slab, Roof slab, Beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

Providing and Laying in Position ,Standardised Concrete Design Mix M-25 Grade in accordance with IS 456 using 20mm and Down Graded Hard Broken Granite Stonejelly for all RCC item of Works with minimum Cement Content of 350 kg/m3 and maximum water cement ratio of 0.55 including admixture (Plasticiser /Super Plasticiser )in recommended proportions as per IS 9103 to accelerate retard setting of Concrete,improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg of 0 mm machine crushed Stone jelly and with about ( 3.3 cu.m ) 5156 kg of 10-12 mm machine crusshed stone jelly and with about (4.79 cu.m ) 7670 kg of crushed stone sand ,but excluding cost of Reinforcement Grill and Fabrication charges ,Centering and Shuttering and also including laying, Vibrating with Mechanical Vibrators ,Finishing curing etc complete nd providing fixtures like fanclamps in the RCC Floor /Roof Slabs where ever necessesary without claiming etc complete complying with standard specification and as directed bythe departmental officers .

Foundation & Basement

Ground Floor

Supplying fabricating and Placing in Position of Ribbed Tor Steel for all RCC works as per Design given including cost and Conveyance of Steel , binding wire and labour charges for bending,tieing in position in all Floors etc .complete complying with standard specification.

Brick work in Cement Mortar 1 : 5 (one cement and Five M.Sand ) using II Class Ground moulded Chamber Burnt Bricks 9'' x 4.3/8'' x 2.75 '' for foundation and Basement including cost conveyance of all materiles and labour chages including curing etc complete.

Foundation & Basement:-

Brick work in Cement Mortar 1 : 6 (one cement and Six M.Sand ) using II Class Ground Moulded Chamber Burnt Bricks 9'' x 4.3/8 '' x 2.75 '' for SuperStructure including cost conveyance of all materiles and labour chages including curing etc complete.

Ground Floor:-

First Floor

Brick Partion Walls of 11.50cm thickness using Best quality Country Bricks 8.75''x4.25''x2.75'' in Cement Mortar 1:3 (One Cement and Three Sand ( Hoop Rod Reiforcement if found necessessery it will be Paid Seperatly ) including cost and convevyancee of all materiales and labour charges etc complete.

Ground Floor:-

Special Ceiling Plastering in CM 1:3,10mm thick and Finishing the exposed Surface of all RCC items of work such as Slabs,Beams,Sunshade,Facia,Canopy Slab,Stair Case Waist Slab ,Landing Slab etc Complete .

Plastering in Cement Mortar 1:5 ( One Cement and Five M.Sand Plaster ) ,12mm thick in all Floors including cost conveyance of all materiales andlabour charges including curing etc complete complying with standard Specification.

STRUCTURAL STEEL WORK

Designing Providing and Fixing in Position Hot Rolled Structural Steel Members .Sections consists of MS Joists ,Channels,Angless, Purlin,Pipes Hollow Tubes runners,insert plates ,Flats etc., at all levels Surface preparations of all MS members by Sand blasting to SA 21/2 grade and painted with anti corrosive low VOC PU Paint ( Metallic finish ) with compatible primer to a minimum film thickness of 75 microns and 2 coats of low VOC PU paint of Akzonoble make and total dry film thickness 225 microns ( Only main structural supports related to Facade works if required any shall be considered and no base frame or support structure shall not be considered which shall form part of the respective ,Glading and Glazing items ) Refer Particular Specifications for Mode of measurement for this item

Supplying and Fixing Colour GalValume Sheet of 0.47 mm thick including fixing in Position with all necessesary accesseries complete complying with standard specification and as directed by the deprtmental officers.

Supplying and fixing GI Sheet Gutters Fit Collecting Rain water from slopped position of GI Sheet 0.80 cm thick 0.70cm wde with appropriate hanger including fixing in position and necessesery cost of brackets screws, nails etc complete .

Dadooing the Walls with Design Ceramic Tiles of size 450 x 300 x 8mm of approved quality ,Colour and make in all Floors over a Base Layer of Cement Mortar 1:2 ( One Cement and Two M.Sand ) 10mm thick and joints neatly finished including cost conveyance of all materiales and labour charges etc complete

Paving the Floor with Joint Free Vitrified Glazed Ceramic Tiles of Size 305 x305 x 8mm for Flooring approved make and quality with Plain/Colour with Base mortar in Cement Mortar 1:3,10mm thick and pointing with White Cement by adding suitable colour pigments including cost and conveyance of all materiales and labour charges etc complete.

Paving the Floor with PrePolised Concrete Anti Skid Step Tiles ( Required Shape and Design ) of 20 mm thick of approved quality and Colour laid in Cement Mortar 1 :3 (One Cement and Three M.Sand ) 20mm thick and pointed with White Cement mixed with Colour Pigment at he rate of 0.40kg/sqm, and curing etc ,complete complying with standard specification and as directed by the departmental officers ( The make and brand of the Tiles should be got approved by Executive Engineer before use onworks ).

Supplying and Fixing 18/20mm Granite Slab for Urinal Partion and Wash Basin Counter Top with nosing on edges and anchored into the wall to a minimum depth of75 mm with necessesary morar packing including cost and conveyance of all materiales and as directed by the Engineer in charge complying with standard specifications.

Suppying and Paving the Paver Block 83mm thick Flooring using Rubber Mould Paver Block (Colour ) of standard size over the M.Sand cushion including cost conveyance of all materiales ,labour charges and compacting with Power machine Compacter etc complete complying with standard specification.

Plain Cement Concrete 1:2:4 mix (one cement Two M.Sand and Four broken Stone ) using 20mm Iss Hbg metal including cost ,conveyance of all materiales and labour charges etc complete as per standard specification .

Paving the Top of Roof with Solar Refelective Tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement Mortar 1:3 (OneCement and Three M.Sand ) 12mm thick and pointed with Tile Grout ( itotile Grout or Equvalent ) and cement in the ratio of 1:3 for joint ,curing etc ., complete complying with standard specification and as directed by the departmental officers (The make and brand of the Tiles should be got approved by the Executive Enginner before use on work )

Door Frame : Supplying and fixing First Quality Teak Wood Frames for Doors,Windows, Ventilators and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fasts in frames and masonry etc complete in all floors .

A) Teak Wood Scantling Upto 2 m

B ) Teak Wood Scantling over 2m and below 3 m

Supply and Fixing of 35 mm thick Double leaf High Density interior grade marine Ply wood Shutters Pasted both sides 1.5 mm thick Laminate approved Design with 35 x 12 mm .T.W lipping on all edges with necessesary adhesives and CP Screws complying with standard specifications .The cost is inclusive of 1 no lock arrangements ,Handle,Tower Bolt, approved equvalent made SS Ball bearing hinges of Equvalent make of approved make Two noof Floor Two no Floor mounted SS Door Stoper etc., complete as per drawing make Kutty,Sharon,.Frojam . Accesories Make Dorma,Godrej .mounted SS Door Stopper approved make

Supply and Fixing of Single Leaf Solid Core Flush Shutter with Teak Ply Wood on both sides with Teak wood Lipping alround 35 mm thick with necessesary adehsive and CP Screws complying with standard specifications. The Cost is inclusive of One no Lock arrangements. Handle, Tower Bolt approved equvalent make SS Ball bearing Hinges of equvaent make of approved make ,Two nos of Floor mounted SS Door Stopper complete etc.

Sliding Door Providing and Fixing Sliding Door using Aluminium Poder Coating Door Frame and Shutter Section with Mat Finish ,Partly Glazed with 6mm Plain Glass and Partly Panell using 12 mm thick Board size Pre Laminated Particle Board fixed with fixed and Sliding Aluminium Channel and fittings like Two Door Handles One Concealed FourLeaver Lock , Door Stopper Two Nos 150 mm Long PC Aluminium Bolt etc all complete.

Solid PVC Door Shutters Toilet Door using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rebate for housing the shutter.

Supplying and fixing UPVC (Un- Plasticized PolyvinylChloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm125GSMand 100% corrosion free, the profiles are multichambered sections with wall thick of 2mm. The EPDMrubber (black colour) covered with over all the edges offrame and shutter the shutter will be provided withEspag multi power point locks and also it operates ashandle. The corners and joints should be welded andcleaned. Radiations free pin headed plain or browncolour glass 4mm thick should be provided to theshutter and it should not allow leakage of water evenat most ranging storms and should have key lockableaction, security protective hinges, strong lockingsystems and as per size for arresting noise and energyloss. The connecting mechanism between sash andouter frame that enables opening of the window. Thewindow should be fixed to the wall with 100% packingwith screws and silicon packing all round the frames.The window should be got approved from the Executive Engineer before use on work.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride)Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (blackcolour) covered with all over the edges of frame and shutter.The corners and joints should be welded and cleaned.Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Providing and fixing welded M.S. Grills to the Window Openings,along the details as per drawing with necessary screws, bolts and fixed with necessary M.S. lugs embedded in masonry with C.C. 1:2:4 and finishing the surface neatly. Rate shall welding and consumables, etc. complete, as directed. Design of grills and the size of members to be used shall be got approval before put into use & as directed by the Engineer-in-charge.

Supply and Fixing Rolling Sutters of approved make made of required size M.S laths,interloked together through their entire length and jointed together at the end by end locks,mounted an specifically designed pipe shafts with brackets, side guides and arrangements for inside and out side locking with push strength confirming to IS:4454 part 1 and MS Top Cover of required thickness for Rolling Shutters 80x1.2mm MS laths with 1.20mm thick top Cover Main Entrance.including applying a Priming Coat of approved steel primer etc.,complete as per standard specification.

Manufacturing, Supplying and Fixing of Stainless Steel Handrails for Staircase using 50mm dia 304L Grade Stainless Steel Pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia SS Pipe Post of 1.00mm thick asVvertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between.The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding,grinding, polishing, conveyance, electrical charges, etc.complete.

Painting Two Coats over New wood work with synthetic Enamel Ready mixed Paint of approved quality and Colour over one coat Priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting Two Coats over New Iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint including Zinc Chromite Priming Coat in all floors including cost of priming coat etc., complete complying with standard specification. ( The make quality and colour of paint should be got approved by the executive Engineer before use on works.)

Painting Two Coats over Inner Walls by using Plastic Emulsion Paint finish of approved make & shade in two coats over a coat of approved primer and 2 coats of patty to give an even shade as per manufacturer's instruction to the internal plastered surfaces including preparation of surfaces, scaffolding etc. all complete as per drawings and specification for all heights.

Providing Two Coats with Exterior Emulsion Paint finish of approved make & Shade including cost of Paint and labour charges in Two or more coats over a coat of approved primer to give an even shade as per manufacturer's instruction to the external plastered surfaces including preparation of surfaces, scaffolding etc. all complete as per drawings and specification for all heights.

Supplying and fixing in position White / Colour Glazed European Water Closet of Best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittingssuch as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supplying and fixing White / Colour Glazed Indian water Closet, Orissa pattern Parryware or equivalent, with PVC, P or S trap having 110mm dia outlet and 50mm deepwater seal, embedding trap and water closet in cement concrete in 1:4:8 mix.

Providing and Keeping in Stores ,Shifting to the Place of Installaion ,fixing,testing and commissioning of White Viterious White /Colour Large Flat Back Urinal with CP angle Cock Spreadser ,Flushing supported by CI/MS bracket including builtin wall etc complete.

Supplying and Fixing of 15mm CP Two way BIB Cock with Health Faucet of parryware or equivalent make conforming to BIS specification and quality including cost of shellac, thread etc., complete complying with standard specification and including cutting and threading wherever necessary.

Supplying and fixing in Position Best quality and approved make Indian made White / Colour Glazed Earthernware Wash Hand Basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in Position Indian make bevelled Edge Mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks).

Supplying & fixing of Angle Valve Stop Cock with Connecting Hose and Wall Flange. (Make: Parryware or equivalent) incuding cost of materiale and labour charges for fixing etc complete.

Supplying and fixing approved Best quality Brass CP Towel Rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc.,complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supply & fixing C.P Soap Tray of approved quality (Parryware or equivalent) including cost and conveyance complying with standard specificatio etc complete .

Supplying & fixing of Stainless Steel Long body BiB Cock with brackets including fixing over Wall Tile dado complete.(Make: Parryware or equivalent) etc complete.

Supplying and fixing in position best quality PVC soil / Waste Pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition,including testing for any leakages,etc.,complete complying with standard specifications.(The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below Stilt level.

40mm dia

50mm dia

75mm dia

110mm dia

Supplying and fixing in Position Cast iron Nahini / Floor Trap with Stainless Steel Grating / PVC Nahini / Floor Trap with PVC Grating type of size 100 x 75 / 75 x 50 mm with best quality gratings of approved brand fixed over a bed of brick jelly lime concrete 1;2;5 (One lime two sand and five aggregate ) brick jelly 40mm and finishing with cm 1;3(One cement and three sand) including dismantling masonary wherever found necessary and making good to the original condition and giving connections to the cast iron pipe etc, complete complying with standard specififcation and as directed by the departmental Officers.

Supplying and fixing in Position Best quality PVC Soil / Waste PIpes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

75mm dia

110mm dia

160mm dia

Supplying and Fixing in Position 150 x 100mm '' P '' or '' S '' Stone ware Gully Trap 'A' Grade with CI double grattings of size 150 x 150mm and 230 x 230mm at bottom and Top respectively with necessesary Earthwork excavation laid over a bed of brick jelly Cement Concrete 13:6 (one cement,Three M.Sand Six broken brick jelly )150mm thick using 40mmbroken brick jelly including necessesary brickwork and Plastering including dismantling masonry where ever necessesary and re doing the damaged portions to the original conditions using Cement Concrete 1:3:6 using 20mm Stone jelly for fixing the Gully Trap and giving connectons to Stoneware Sewer Line etc ., complete complying with standard specifications.( Earth work excavation, brick work,Plastering shall be measured and paid separately).The Gully Trap should be got approved by the Executive Engineer before use on work )

Construction of Inspection Chamber of the following Clear sizes including Earth work excavation, CC 1:5:10 of 10 cm thick and Brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality Ground d Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Providing, Supplying & laying of Chlorinated Poly Vinyl Chloride (CPVC-SDR-11) Pipes conforming to IS 15778 having thermal stability with Brass and CPVC fittings like Elbow, Brass Tee, Brass Elbow, Offsets, Tee with clamps @1.00 meters spacing, with jointing of pipes with one step CPVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc. Rate is inclusive of all material labour, transportation, tools & tackles taxes, etc all complete as per as per specifications, Exposed work including chase cutting, bracket fixing)complete complying with standard specification and as directed by the Departmental Officer.

20mm dia

25mm dia

32mm dia

Providing, supplying & laying of Unplasticized Polyvinyl Chloride (UPVC-SDR-11) Pipes conforming to IS 15778 having thermal stability cold water with brass and UPVC fittings like Elbow,Brass Tee, Brass Elbow,Offsets,Tee with clamps @1.00 meters spacing, with jointing of pipes with one step UPVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc.Rate is inclusive of all material labour, transportation,tools & tackles all complete as per as per specifications,Concealed work including chase cutting) complete complying with standard specification and as directed by the Departmental Officer.

32mm dia

40mm dia

50mm dia

Providing, supplying & laying of Gun Metal type NRV - Pressure Rating less tahn 16 Kg/Sqcm and IS778 with 2 Nos of MTA with jointing material like shellac, thread including testing of the joints complete and making good the walls etc. Rate is inclusive of all material labour, transportation, tools & tackles taxes, levies VAT etc all complete as per as per specifications, complete complying with standard specification and as directed by the Departmental Officer

32mm dia

40mm dia

50mm dia

Supplying and Erection of Horizontal Shaft Centrifugal Mono Block Power Pump set of Single Phase 2.00 H.P of best approved quality and make with ISI mark on suitable pedastal with foundation bolt and nut including labour supplying and fixing of Starter and Main Switch Suitable for 2.00 H.P pumpset on suitable angle iron frame work with necessary labour including panel board, supply and run off 4 of 10 Sq,mm, in P V C pipe with 14 SWG TC wire including fixing of suction pipe and foot valve up to a maximum depth of 7m and delivery pipes upto the exterior wall of pump room etc., complete and operating the pumps on trial run for 3 days. (The make and quality of pump set to be got approved by the Executive Engineer before use on works.) (TWAD- Pa no:103 Sl.no:45)200mx60m

BORE WELL

Supply of 150mm Dia PVC Casing Pipe

End Cap 150 mm Dia

Drilling of 150 mm dia bore well in Hard Rock area using DTH rig including cost of transportation charges for rig and others supporting vehicle etc.

Supply nd Delivery of Clear water Vertical Type Single Phase Sbmersibble Pump Set 2.0 hp Confirming to IS 8034 / 2002 under amendment there after and be Three Star Rated capable of Discharging noted LPM against in terms of Wter Column due to ll causes .the Pump shall be with Stainles Steel Shaft and Automatically balanced with brozon or Cast impeller Brass Screws and CIFG 200 Grade Pump,bowel,/ diffuser with ISI mark. The Pump Shall be dirctly coupled to a contionues rated to pole suitable wET Type Required induction Motor Suitable for Operation inAC Single Phase to 230 V etc., complete. WD- m 1592 -20 LPM X 150 M

Supply and delivery of2.50sq.mm PVC insulated and sheathed 3 core flat type copper cable confirming to IS 694/1990 with ISI mark.

Supply and Delivery of 3.00 m Long 32mm dia UPVC Column Pipe for downward extention of pump AS per SOR WD- M OO49 with part one of 3.00 m long

Supply and delivery of 32 mm GI Coupling Heavy

Supply and delivery of 32 mm GI Elbow Heavy

Supply and delivery of 32 mm Flange Sets with Rubber Sheet with Bolt and Nuts

Supply and delivery of 32 mm GM Gate Valve as per specification

Supply and delivery of 32 mm Dia GI Hex Nipple as per specification

Supply and delivery of 25 mm Dia GI Pipe Heavy for EB Service Connection

Supply and delivery of 20 mm Dia GI Pipe Heavy as per specificaton

Supply and delivery of 20 mm GI Coupling Heavy

Supply and delivery of 25 mm GI Elbow Heavy as per specification

Supply and delivery of 20 mm GI Elbow Heavy as per specification

Supply and delivery of 20 mm GI Nipple Heavy as per specification

Supply and delivery of 20 mm Dia Chromium Tap as per Specifications .

Twin Earthing as IE Rule including cost of 25mm GI Pipe etc., complete .Supply and delivery of electrical item as IS Specification and as per IE Rule .

Teak Wood Board For FixingMetre and Paneel Board 12 '' x 18'' x 3''

32 Amps 500 V Porcelin Fuse Unit

7 / 20 Copper Wire ( 90m Length )

15 W LED Bulb with Holder

15 Amps Switch

Aerial Board 20 x 15 cm

Labour Charges for Errection of Submerssible Pump Set in Deep Bore Well including connection of Submerssible Pmp Set with Submersible Gable and GI Pipes and Specials with all incidential charges etc ., complete.

Supply and Errection of PVC Water Tank , the Rate inclusive of Labour and Transportation and complete complying with Standard Specification and as directed by the departental officers. (The make and Brand of PVC Tank should be got approvedby the Executive Engineer before use on work )

ELECTRICAL WORKS:-

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End ) (Data A1)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End (Data A2 )

Supply and fixing of 4' 20W LED fitting with LED on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting (Higher end) (Data A3)

supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting (SD 448)

Supply and fixing of BH Point with 15 W Bulb ( SD 80 Less cost of Fancy Glass Shade )

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb (SD 84)

supply and fixing of 1400mm (56") sweep AC ceiling fan complete ( Lower end) with 2 module 100W fan step regulator (Lower end) with 600mm down rod on the exisitng fan clamp (SD499)

Supply and fixing of 300mm (12") sweep (Heavy duty) AC exhaust fan complete with necessary wall opening and making good of the wall (Data A4)

Supply and fixing of Louvers Shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan (SD 120)

Supply and fixing of 2nos.6A Two Module 5 Pin Socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (SD 383)

Supply and fixing of 1 no.6/16A Two Module Socket , 1 no. 16A one Module switch with Module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (SD 401)

Supply and fixing of 4 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A DP MCB switch as incoming and 2 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End (Higher end) (Data A5)

Supply and fixing of 8 way Single Pole and Neutral MCB sheet steel enclosure distribution board with double door (metal) 1 No. 32A DP MCB as incoming and 6 Nos. 6A to 32A SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (Higher end) (SD 151)

Supply and fixing of 4 way Vertical Tripple Pole and Neutral MCB sheet steel enclosure distribution board with double door (metal) 1 No. 63A 4P MCB as incoming and 1 Nos. 32A 3PMCB 9 no 6 Amp to 32 Amp Sp MCB as outgoing on wall with earth connection only. Higher End DATA - A6

Supply and fixing of 32A DP MCB with sheet steel enclosure on wall with earth connection (Higher end) (Data A6)

Supply and fixing of 32A 4P MCB with sheet steel enclosure on wall with earth connection (Higher end) (Data A8)

SupplyandFixing of TNEB Meter Board Suitable for Three Phase 63 Amps Service connection made up of suitable Angle Iron Frame work of size Two Feet one and Half Feet using Angle Iron of Size 1.5 F X 1.50 f x 0.25 '' rigidly fixed on wall covered hyleyum Sheet of size 2' x 0.5' of 6 mm thickness with necessesary bolt and nuts support and supply and fixing of three nos 63 Amps Fuse Unit ( 500 V 0 1 No Neutral Link Copper Earth Flat of size 1'' x 0.25 '' with inner connection of EB Meter Two FUSE uNIT 16 Sqmm .PVC Insulated Copper Wire with One no 63 Amps 30 MA Four Pole RCD/RCCB with suitable necessesry connection with eart connectioncomplete. ( SD 131 )

Supplying and Fixing of TNEB Metre Board suitable for 32 Amps Single Phase Service Connections with 32 Amps FuseUnit ( 500 V ) 32 Amps Neutral Link and Earth Link 1'' x 1/18'' COPPER Flat on TW Plank of Size 375mm x 30 mm x 19 mm with Supporting TW Reepers of 1'' thick on eiether side with painting with suitable Bolt and Nutts for fixing the TW Plank onthe wall with Earth Connections and inner connections with 7/20 PVC Insulated Copper Wire from EB Meter to Fuse Unit with one no 40 Amps 30 MA Double Pole RCD / RCCB ( Higher End ) with suitable necessesary connection. ( SD 125 )

Supply and fixing of 32 Amps DP RCB with steel sheet enclosure on wall with Earth connections ( Higher End ) Data -A9

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 6 sq.mm copper wire and making good of the concealed portion with suitable colour (SD 57)

Supply and run of 2 of 6sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 6 sq.mm copper wire and making good of the concealed portion with suitable colour (SD 59)

Supply and run of 4 of 16 Sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 6 sq.mm copper wire and making good of the concealed portion with suitable colour (DATA-A10)

Supply and Laying of 2 x 16 sq.mm. PVC LTUG armoured alu. Cablein suitable size HDPE Pipes in a trench to be excavated at a depth of 0.75 m and Re filling the Earth to make Good (DATA -A11)

Supplying and Clamping of 2 x 16 Sqmm PVC LT UG Aromount Aluminium Gable on Post or on Wall with MS Clamp ( SD 195 )

Supplying and Clamping of 2 x 16 Sqmm PVC LT UG Aromount Aluminium Gable in suitable size of GI Pipe on on Post or on Wall with MS Clamp ( DATA A12)

Supply and Run of 4 x 10 sqmm PVC insulated unseathed FRLS Copper Conductor of 1100 UG Gable in suitable Gauge PVC Conduit PVC contionues with 2.5 sqmm Copper wire making concealed Portion ( SD 342 )

Supply and fixing of Brass Gable Gland for 2 x 16 sq.mm. PVC armoured LTUG cable with earth connection (SD 161)

Supplying and Laying of 4 x 16 Sqmm PVC Armount LT UG Alu Gable in suitable size HDPE Pipe in a trench to be excavated at depth of 0.75 m and refilling earth make to make Good ( SD 658 )

Supplying and Clamping of 4 X 16 Sqmm PVC LTUG Armount Alu Gable on Post or on wall withMS Clamp ( SD 199 )

Supplying and Clamping of 4 X 16 Sqmm PVC LTUG Armount Alu Gable in suitable GI Pipe on Post or on wall with MS Clamp ( DATA A 13 )

Supply and fixing of Brass Cable Gland for 4 x 16 sq.mm. PVC armoured LTUG cable with earth connection(SD 163)

Supply and Laying of 3 1/2 x 25 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.(SD 659)

Supply and Clamping of 31/2 X 25 Sqmm PVC LTUG Armounted Alu Gable on Post or Wall with MS Clamp ( SD 200 )

Supply and Clamping of 31/2 X 25 Sqmm PVC LTUG Armounted Alu Gable in suitable GI Pipe on Post or Wall with MS Clamp ( DATA A 14 )

Supply and Clamping of 31/2 X 25 Sqmm PVC LTUG Armounted Alu Gable with eart conections ( SD 164 )

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD 211)

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth Connection (SD 371)

Compound Wall

Earthwork excavation for Narrow Trenches in all soils and sub soils to full depth as may be directed except in hard rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary refilling the foundation with excavated earth other than sandy soil in layers of not more than 15 cm thick layers well rammed and depositing the surplus earth within compound in places shown by the departmental officers with an initial lead of 10 metre and initial lift of 2 metre and clearing and leveling the site etc., complete complying with standard specification and as directed by the departmental officers

Plain Cement Concrete 1 : 5 : 10 ( One Cement Five M.Sand Tend Broken Stone ) using 40mm ISS Hbg metal including cost conveyance of all materiales and labour charges etc coplete as per standard specification .

Supplying and Errecting ,Centering for Sides and Soffits including Supports and Strutting Upto 3.30 M Heigh with all Cross Bracing for Plane Surface using Mild Steel Sheets of 90 x 60 cm 10 G Stiffened with MS Angle of 25 x 25 x 3mm

A ) For Below Ground Level

B ) For Column

Providing and Laying in Position ,Standardised Concrete Design Mix M-25 Grade in accordance with IS 456 using 20mm and Down Graded Hard Broken Granite Stonejelly for all RCC item of Works with minimum Cement Content of 350 kg/m3 and maximum water cement ratio of 0.55 including admixture (Plasticiser /Super Plasticiser )in recommended proportions as per IS 9103 to accelerate retard setting of Concrete,improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg of 0 mm machine crushed Stone jelly and with about ( 3.3 cu.m ) 5156 kg of 10-12 mm machine crusshed stone jelly and with about (4.79 cu.m ) 7670 kg of crushed stone sand ,but excluding cost of Reinforcement Grill and Fabrication charges ,Centering and Shuttering and also including laying, Vibrating with Mechanical Vibrators ,Finishing curing etc complete nd providing fixtures like fanclamps in the RCC Floor /Roof Slabs where ever necessesary without claiming etc complete complying with standard specification and as directed bythe departmental officers .

A ) For Upto Basement

B ) For Above Basement

Supplying fabricating and Placing in Position of Ribbed Tor Steel for all RCC works as per Design given including cost and Conveyance of Steel , binding wire and labour charges for bending,tieing in position in all Floors etc .complete complying with standard specification.

Brick work in Cement Mortar 1 : 6 (one cement and Six M.Sand ) using II Class Ground Moulded Chamber Burnt Bricks 9'' x 4.3/8 '' x 2.75 '' for SuperStructure including cost conveyance of all materiles and labour chages including curing etc complete.

Providing and Fixing Welded MS Grill to the Opening along the detailes as per Drawing with necessesary screw bolt and fixed with necessesary MS Laths embeded in masonrywith CC 1:2:4 and finishing the Surface neatly rate shall welding and consumable etc .complete as direct Design of Grill and the size of member to be used shll be got approved before put in to use.and as directed by the Executive Engineer .

Ornamental Brick work in Lime Mortar 1 : 2 mix using Class II Ground Moulded Chamber burnt Bricks of Size 9''x43/8'' x 23/4'' all vari VARGAMS Mould Sthambas,Mukapatram,Koodu,Nasi and all ornamental brick work complte Panchavarnam ,agaries,karnakoodus etc forming core wall Raja Gopuram/vimanams complete including cement and Labor charges 25' fee

Providing Vargapoochu over the Core Wall of Vimanam/Gopuram with Lime mortar 1:1 :5 complete including shaping the Mukhapathram, Mahannasi,Koodu all Ornamental work to proper Shape by embeding broken bricks or shaped/chiselled bricks Rough - Plastering with Lime motor 1: 1.5 and Conveyance of all materials labour therefore Lifting of Matertials all Working in Height curing with water etc Compelet Invluding all extra for folding and inclding clearing the debris from Vimanams / Gopurams Upto 25'0'' Height excluding kalkaram

Plastering in Cement Mortar 1:5 ( One Cement and Five M.Sand Plaster ) ,12mm thick in all Floors including cost conveyance of all materiales andlabour charges including curing etc complete complying with standard Specification.

Painting Two Coats over New Iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint including Zinc Chromite Priming Coat in all floors including cost of priming coat etc., complete complying with standard specification. ( The make quality and colour of paint should be got approved by the executive Engineer before use on works.)

Providing Two Coats with Exterior Emulsion Paint finish of approved make & Shade including cost of Paint and labour charges in Two or more coats over a coat of approved primer to give an even shade as per manufacturer's instruction to the external plastered surfaces including preparation of surfaces, scaffolding etc. all complete as per drawings and specification for all heights.

RETAINING WALL

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD 211)

Supplying and Filling with M. Sand in Foundation and Basement of layers not more than 15 cm thick well rammed and consolidated including cost and conveyance of materiales and labour charges etc complete.

Plain Cement Concrete 1 : 5 : 10 ( One Cement Five M.Sand Tend Broken Stone ) using 40mm ISS Hbg metal including cost conveyance of all materiales and labour charges etc coplete as per standard specification .

Supplying and Errecting ,Centering for Sides and Soffits including Supports and Strutting Upto 3.30 M Heigh with all Cross Bracing for Plane Surface using Mild Steel Sheets of 90 x 60 cm 10 G Stiffened with MS Angle of 25 x 25 x 3mm

Plain Cement Concrete 1 : 2 : 4 ( One Cement Two M.Sand Four Broken Stone ) using 20mm ISS Hbg metal including cost conveyance of all materiales and labour charges etc coplete as per standard specification .

Supplying and Filling with Gravel in Foundation and Basement of layers not more than 15 cm thick well rammed and consolidated including cost and conveyance of materiales and labour charges etc complete.

Providing Weep Holes Pipe by 50mm PVC Pipe etc , complete .

Supplying fabricating and Placing in Position of Ribbed Tor Steel for all RCC works as per Design given including cost and Conveyance of Steel , binding wire and labour charges for bending,tieing in position in all Floors etc .complete complying with standard specification.

shanmathi constructions private limited (BID ID -1299933)