Interior and Fit-out works in office space of Petroleum and Natural Gas Regulatory Board (PNGRB) at 4th floor, E-400, Tower-E, World trade Centre, Nau

S NO DESCRIPTION AMOUNT AMOUNT

6.00 WI-FI & LAN WORKS (ACTIVE & PASSIVE) 0.00 1,53,19,302.00

9.00 FIRE ALARM & PA SYSTEM 8,41,252.00 22,85,366.00

17.00 GAS SUPPRESSION SYSTEM 0.00 13,99,012.00

19.00 RODENT & WLD SETUP 0.00 2,79,308.00

Total (DSR+MR) 17,28,95,719.90

Total w/o GST 14,65,21,796.52

Digitally signed by SAKET

SCHEDULE OF QUANTITIES-CIVIL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

1 FLOORING WORKS

CEMENT CONCRETE: Providing and laying in position CEMENT CONCRETE of specified grade exluding the cost of centring and

1.01 shuttering-all work upto plinth level.

4.1.8 1: 4: 8 (1 Cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size) 200.8 CUM 6812.00 1367849.60

RAISED FALSE FLOOR: Providing and fixing removable raised/false access flooring with systemand its components of approved

make for different plenum height with possible height adjustment upto 50mm, comprising of modular loadbearing floor panels

supported on G.I. rectangular stinger frame workand G.I. Pedestal etc. all complete, as per the architectural drawings, as specified

and as directed by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm

outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal

head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the

stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be

fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug.

(b) Stringers system in all steel construction hot dipped galvanized ofrectangular size 570x20x30x0.80mm thick having holes at both

ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions,

the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid

11.54 support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for

1.02 electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of

800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64

hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together

(minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust

protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with

lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp

technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated

Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The

panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the

approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of

the panel to ensure the quality of the product.

11.54.2 450mm Finished Floor Height (FFH). 21.48 sq m 5977.35 128393.48

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thickness

1.30 to 1.50mm. Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

ENGINEERED WOODEN FLOORING: Supplying and Installation of engineered wooden flooring of total thickness 13 mm -16 mm,

1.04 MR Toplayer PEFC controlled Core board PEFC controlled Backing layer PEFC controlled sources Wood Veneer 2 mm Tongue and 519.84 sq m 5765.00 2996877.60

groove Length Uniclic Width Uniclic Multifit Domestic use Conditions as per direction of engineer in charge.

VITRIFIED TILES: Providing and laying vitrified floor and wall tiles in different sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick

cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white

cement and matching pigments etc., complete.

Size of Tile 1200x600 mm

2 Digitally signed by SAKET

CARPET TILES: Providing and laying Carpet tiles of Yarn type Eco Solution Q® Nylon (Nylon 6) only; Multi-Level Pattern Loop,

manufactured using 100% solution dyeing process, Shaw Carpet with Rubberised Cushion backing as per details given below. The

carpet shall have minimum production yarn weight equivalent in range of 15 oz/yd² or more having tufted yarn weight of 508.6 g/m² or

more, Average Density 5938 oz/yd³ or more.

Size of Tiles: 61 cm x 61 cm/ 23 cm x 91 cm.

The carpet should carry a warranty not less than 15 years from the manufacturer and supplier of carpets. The carpet shall have a pile

height ranging from 2.5 mm + / - 0.5mm and total thickness of the carpet tile shall also range from 5.6 mm + / - 0.5mm.

Radiant Panel class 1rated ( ASTM E648), NBS smoke < 450, Pill test -Passed, Anti Static Property less than 3.5 kv, Texture

1.06 MR Appearance Retention Rating of 3.5 for severe use, Anti-Microbial Treatment-Passes (AATCC-174). CRI Green Label Plus is certified 908 sq m 2562.00 2326296.00

for indoor air quality, including fixing/ installation with Low/ Zero VOC content Adhesive. Impact Sound (ISO 10140-3) 20 dB & Sound

absorption (ISO 354) 0.2 Class D.

Mandatory Environmental Certifications- Cradle to Cradle Silver Certified standard Version 4.0 +Declare LBC Compliane + LEED V4

compliance+ EPD + HPD+ NFS 140 Gold+ CRI Green Lable Plus+ green leed contribution credit. Product to have recycled and

Recyclable content. The product has a lifetime commercial warranty of 15 years and also has a Global Reclamation policy at the end

of the life cycle of the Carpet to avoid carpets going to landfills.

IPS FLOORING: 52mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener

1.07 11.4 consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed 1432.84 sq m 978.45 1401962.30

@ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of

nosing of steps etc. complete.

ITALIAN MARBLE: Providing and laying machine cut, mirror polished, Italian Marble brass brass inlay stone flooring laid in required

pattern in linear portion of the building all complete as per architectural drawings, with 18mm thick stone slab laid over 20mm

1.08 11.51 (average) thick base of cement mortar 1: 4 (1 cement: 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm

including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing

etc. all complete as specified and as directed by the Engineer-in-Charge.

11.51.1 18 mm thick Italian Marble stone slab in all colour and shade 634.75 sq m 6603.35 4191476.41

LAMINATED WOODEN FLOORING: Providing and laying 8.3 mm thick AC5 grade laminate wooden flooring having good castor

chair and furniture resistance strength. Plank dimension to be 1215x195x8.3mm with clock locking system and wax coating for better

1.09 MR sound resistance. Impact and abrasion resistance to be of high grade having class EN 13329. The flooring shall be laid with 2mm 0 sq m 2159.00 0.00

thick underlay and PVC sheet and prevent against moisture and foot taping sound. The item also includes the skirting and any other

profiles required for proper installation.

TOTAL FLOORING WORKS 7489796.71 5607573.6

2 FALSE CEILING WORKS

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including providing and fixing of frame work made of

special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS :

277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre,

one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate

G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom

wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction

perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction,

2.01 12.45 including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed

to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including

jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes ,

finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all

as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with

frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but

excluding the cost of painting with

12.45.1 12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) 1228.73 sq m 1355.80 1665912.13

3 Digitally signed by SAKET

LOUVERED WOODEN FALSE CEILING & WALL PANELS: Providing and fixing Acoustics panel of size 600 (covering

area)x2400mm having thickness of 43 mm with sound absorption of 0.7 NRC*

Material: Wooden Batons over Mineral Fiber

Board type: custom-made acoustic board with 12 wooden strips on the front and 5 plywood strips on the back.

Length x width x thickness: 600x2400zx43

Reaction To Fire: D-s1, d2 eller D-s1, d0 *

Sound Absorption: 0,7αw

Sound Reduction: 14dB

Heat Conduction: 40W/m K

Indoor Climate VOC: A+

Formaldehyde: E1-M1

SPECIAL SQUARE BAFFLE CEILING: Providing of aluminum modular cube open cell ceiling system, manufactured of roll formed

Aluminum U profile 24mm/15mm wide, made of upper & lower blades to form a 600x600mm modular panels with 100x100 cell in

0.7mm thick . Fixed on (24mm or 15mm) T-Grid suspension system, in order to allow easy access to ceiling void.Blades sizes will be

in 24(W)x50(H).Special boxes will be provided for MEP Services.The aluminum alloy for ceiling shall be as per EN AW 3000 or 5000

series.The substructure consisting of ASTM C635 tested/ICC-ES-AC evaluated.Fire performance shall be as per ASTM E84-Class A.

The production unit shall be quality controlled to ISO 9001:2008 / ISO 14001 standards. The ceiling shall be manufactured on

2.03 MR advanced equipment which includes several leveling stages in manufacturing process. Finishes of ceiling shall be powder coated 28.2 sq m 15830.00 446406.00

base of minimum 80 microns coating thickness. Powder coating application shall be done post-fabrication of ceiling as per architects

selection. No Pre Coated products shall be accepted. The acoustical performance shall be tested by approved test center with a

minimum of sound absorption of 1.0 NRC as per ASTM C423/BS EN 354:2003 and 41db sound transmission as per ASTM E1414-

11a. Perforation pattern to be 1.8mm diahole (RD1850 pattern), with minimum 20% open area. Insulation to comply with the

acoustical performance requirements.

WAVE BAFFLE CEILING: To Supply & Install Custom made Vertical curve Polylam Blades Ceilings as per the design intent. The

vertically curve baffle system POLYLAM exhibiting space- delineating characteristics. The system comprises vertically curve baffle

with 75-150mm deep curved rafters manufactured out of 1.2mm Aluminium to provide wave effect. The module for fixing baffle shall

be 150mm centres as per design requirement. The carrier rails run perpendicular to the baffles axis and can be mounted with M6

threaded rods using technical approved fasteners as per EN 13964 standards. The individual baffle lengths between 1200- 2400 mm

2.04 MR can be selected. Baffles lengths less than 1500mm required two carrier rails mounted at the baffle ends. Baffle longer than 1500mm 60.13 sq m 8328.00 500762.64

require additional carrier rails mounted in the centre. Finish RAL Powder Coated.No Pre Coated products shall be accepted. The

spacing of the grid angles is according to the requirements of DIN 18168 and DIN EN 13964 and quality controlled to ISO 9001:2015

approved by SIS & LEED certification by Indian Green Building council (IGBC).

GYPSUM ACOUSTIC CEILING: Providing and fixing suspended Demountable acoustic ceiling in recessed grid system Belgravia 600

x 600 x12.5mm E with Unity 4mm holes end to end perforation, c/c 15 mm with 0.8 NRC*

Material: High Grade Glassfiber Reinforced Perforated plasterboard with Cleaneo Technology

Board type: Ceiling tile

Length x width x thickness: 600x600x12.5mm

Edge: E recessed grid system ( 8mm recess)

Perforation: Unity 4mm holes end to end perforated

Surface: Water-based acrylic paint

Colour: White NCS 0701 Y24R, closet match to RAL 9003; gloss 5

2.05 MR Attachment: 15 T-grid system 71.28 sq m 3194.00 227668.32

Suspension: Recessed grid system

• Sub-division executed with cross - sections length 600 mm

• Screw spacing for attachment of edge sections length 600 mm

• Light sockets of upto 1.5 kg can be integrated directly into the ceiling tiles. In the case of heavier fittings, load must be taken up

directly by the concrete deck or via the grid systemand extra hangers.

Fire rating: A2-s1,d0

4 Digitally signed by SAKET

GYPSUM LOUVERED CEILING: 12.5x600x600 high grade, glass-fibre reinforced, acoustic, gypsum panel with acoustic perforation

as Unity 3 - square 3.5x3.5mm c/c 8.33 type U3. The ROLD 12 tiles with Strip shall be screw fixed on minimum 60mm wood or steel

furring. The ROLD 12 with strips tiles are with edge B+ and are pre-painted ready for installation on site. ROLD 12 screws, type Torx

15, with white-painted head are used for screw-fixing. The acoustic ROLD 12 tiles are furnished with a grey (white) absorbent felt

2.06 MR backing with an airflow resistance of 330-460 Ns/m³ (DIN 53887).Colour - White, NCS 0701 Y24R, gloss 5 (standard) or re-paintable 228.2 sq m 17937.00 4093223.40

at site with water based acrylic paint.Closest match for repainting: NCS 0700/RAL 9003. Paint Type - Waterbased acrylic emulsion

paint including titanium for hygienic indoor climate. Light Reflection: 69.2% according to DIN Norm 5036.Acoustic Property - αw: 0.95;

NRC: 0.90.Fire Class - A2-s1,d0 .Suspension - The ROLD 12 must be screw fixed to furring of 22 mm wood or 60mm steel battens at

ACOUSTIC BAFFLE CEILING: Supply and installation of 2400 x 200x 18 mm PET Panels with a density of 1850 gsm, material -100%

polyester fibre , 100% recyclable and highly durable with GI U channel and clutch wire for hanging.

LINEAR OPEN CELL CEILING: Providing and fixing of Starlum 9 linear cell ceiling made out of Aluminium. The assembled cell

ceiling panels shall be in size of 600x1200mm. The assembled cell ceiling panels shall made out of main blades in 9mm (W) x 40mm

(H) in 1200mm (L), installed at 66.66 mm c.c. and cross connected to secondary blades in 15mm(W) x 37mm (H) in 600mm (L) with

240 mm pitch. The assembled cell ceiling panels are then clipped into U-94 carriers in GMS,coated in black enamelled finished at

1200mm c.c. Wire clips shall hold the cell ceiling panels into the U-94 carriers. Once the U-94 carriers are installed then primary

angles made out of GMS, type U1040 are cross connected to the U-94 carriers at 1200mm c.c. for lateral bracing The whole ceiling

shall be suspended by M6 threaded rods installed at 1200mm c.c. The panels are fully downward demountable / hinged from the

proprietary U 94 carrier section using C 94 spring panels.The system should be in accordance with Material class A2-s1, d0 according

to EN 13501-01 “non-combustible”, as per the Direction of Arch-in-charge. The system will meet fire retardant standards of BS 476:

Part 6 & Part 7. Tolerances according to TAIM, DIN EN 13964 and quality controlled to ISO 9001:2015 approved by SIS, LEED

certification by IGBC.All panel modules must be hinge able through wire clips. Finish of cell ceiling panels: Metallic silver in RAL 9006

& RAL 9016 White colour.

GYPSUM TILE FOR WET AREAS: Providing & fixing of DANOTILE , high humidity resistant, made of special high grade, glass fibre

reinforced gypsum, 600x600x9.5mm thick, 30 min fire rated* (third party certificate ), A2,s1-d0, mounted on T-24 exposed Grid

suspended ceiling system which includes Main Tee at every 600mm c/c and Cross Tee, 600mm. Wall angle is then fixed along the

perimeter of wall with screws (as per manufacturers specification). The suspension is done with all accessories like Soffit cleat,

leveling clips & wire rods as per design, drawings and architects instruction.The tiles are machine laminated with non-toxic PVC free

foil on the face side & red poleyethelene foil backing on the reverse side. Charachteristics : The Tiles shall be:

2.09 MR • Manufactured from high grade non-combustible glass fibre reinforced gypsum board produced according to EN 520. 48.92 sq m 1794.00 87762.48

• Tested to meet the safety requirements of EN 14190.

• Tested in accordance with EN 13501-1 to achieve minimum fire classification A2-s1,d0.

• Resistant to 90% RH and short term exposure for higher humidity.

• Non hazardous and fully recyclable.

The entire work shall be done as per design, drawings and direction of engineer in charge.

TOTAL FALSE CEILING WORKS 1665912.13 12069379.27

3 WALL FINISHES WORKS

GLASS PARTITION (FIXED DOUBLE GLAZED GLASS PARTITION): Supply & Installation of Modular Double glazed partitioning

frame of 100mm System, (100mm x 25mm) as wall starter and top section, Using (100mm x 25mm) as wall starter and top section,

Using (100mm x25mm) as bottom channel. Glass to Glass butt joint with I, L & T profiles. 10mm + 10mm thk clear toughened glass.

Required accessories like Gasket and Adhesive tapes as per standard partition height upto 2500mm.

FRAMED HINGED GLASS DOOR: Supply and Installation of Modular Aluminium single leaf stile door frame of make 100 mm System,

3.02 MR using (100mm x 25mm) as door frame, using for Stile door Shutter 75x45mm with 5mm + 5mm thk clear thoughened Glass. All 52 Nos. 102495.00 5329740.00

hardware shall be included in the item. The Door Handle size shall be 922 mm x 22.

5 Digitally signed by SAKET

SWITCHABLE GLASS: (A) Supply of 12mm SGG- Priva - Smart Laminated Glass (2 x Extra clear glass - 5mm thickness of 120 ppm,

4 x PVB interlayer of 0.38mm thickness, 1 x smart film layer of 0.4mm thickness) confirming to EN 356 standards. The SGG - Priva

Smart Laminated Glass should be able to confirm to a haze level of less than 6% during ON condition and 99% during OFF condition.

It should be able to provide an acoustic reduction of (RW (C;Ctr)) 36dB. The smart glass assmebly should be IP68 rated. The Smart

3.03 MR Glass system should be able to switch for 3 million cycles (ON/OFF) (B) Supply of electrical cables (upto 20m) 0 Sqm 77642.00 0

The cables should be UL 2464 certified and the connectors should be IP67 certified. (C) Supply of power supply units to control the

smart glass. The power supply units should confirm to electrical safety standard of EN 60335-1, EN 55014-1:2021, EN 61558-1

WOODEN DOOR FRAMES: Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed

9.1 and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for

3.04 separately).

9.1.1 Second class teak wood 0.696 cu m 142949.70 99492.99

WOODEN BATTENS: Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling

3.05 necessary holes for rawl plug etc. including priming coat complete.

8.27.1 Kiln seasoned and chemically treated hollock wood 2.3 CUM 187277.65 430738.595

FLUSH DOOR SHUTTERS: Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,

9.21 core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains

3.06 or cross bands and face veneers on both faces of shutters:

9.21.1 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws 65.76 SQM 2392.65 157340.66

WOODEN LIPPING: Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door

shutters (over all area of door shutter to be measured).

Providing and Fixing -900 mm or equivalent D-type Handle Material : Stainless Steel. Finish : Satin Stainless Steel (SSS). of

approved make and model all complete as per the direction of Engineer-in-charge.

Providing and Fixing Mortise Lock Body SB/TB for door thickness 25-50 mm for of approved make and model all complete as per the

direction of Engineer-in-charge.

Providing and Fixing Double cylender Floor Spring- with Closing Force EN 3 with Maximum door weight 105 Kg. Maximum door width

950mm.Closing speed : 130°

Final closing speed : 15-0°. Hold Open (standard): 90° hold open. Weight of floor spring approx : 6kg, 5,00,000 cycles Tested with 5

Years Warranty against manufacturing defect. CE certified for wooden doors all complete as per the direction of Engineer-in-charge.

Providing 40x5mm flat iron hold fast 400mm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and

3.11 9.53 embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm 25 EACH 228.85 5721.25

Providing and Fixing top and bottom strap of approved make and model all complete as per the direction of Engineer-in-charge.

WOODEN DOOR LOCK: Providing and Fixing Dead lock Back set- 50 mm with Key Hole of approved make and model all complete

as per the direction of Engineer-in-charge.

WOODEN DOOR LOCK: Providing and Fixing SS Cylinder One side knob and one side regular key (3 key) for wooden doors of

approved make and model all complete as per the direction of Engineer-in-charge.

GLASS FILMS: Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce

Sand-blasting effect on glass with customised designs, thickness of 2 mil (0.05mm) without adhesive & 3mil (0.8)with adhesive having

minimum tensile strength of 3.5 pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch

(0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors) .

6 Digitally signed by SAKET

LACQUERED GLASS: Providing and fixing of 6mm thick annealed SGG Planilaque Evolution (premium GRIHA rated lacquered glass

from Saint-Gobain) of approved color by Architect/ Client / Customer, fixed with SGG ULTRAFIX (compatible neutral core silicon/

double sided tape) on a perfectly leveled 12mm thick water proof marine plywood / MDF / Mineral fibre board which is mounted on the

RCC wall/any other structure. Lacquered glass must be made industrially (via curtain coating process); opaque (if viewed against a

3.16 MR support wall), coated with PU lacquer (50 micron thick); color consistency (measured by Minolta spectrophotometer CM5081); highly 136.4808 SQM 5112.00 697689.85

durable (passes PERSOZ hardness test for minimum 220 oscillatios); humid resistant (conforms to BS EN 1036 1999);

environmentally friendly (no lead, no arsenic, no copper, noformaldehyde); appropriate recycled content (12% post industrial/ 6% post

consumer); compressive strenght (1000 MPa) & tensile strength (40 MPa), same as float glass;

GYPSUM BOARD PARTITION: Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including

providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both

side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor

and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor

fastener or metal screws with nylon plugs and the studs 48mm wide having one flange of 34 mm and other flange 36 mm and 0.50

mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia

bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws

9.105 with nylon plugs at spacing of 450mm centre to centre, and fixing of boards to both side of frame work by 25mm long dry wall screws

3.17 on studs, floor and ceiling channels at the spacing of 300mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99mm width (0.9mm thick having two flanges of 9.5mm each) to be provided

at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush

finish with recommended jointing compound, jointing tape, angle beads at corners (25mmx25mmx0.5mm), joint finisher and two coats

of primer suitable for board as per manufacturer's specification and direction of engineer in charge all complete.

75mm overall thickness partition with 12.5mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming

to IS: 2095: part 3 (Board with BIS certification marks)

ACRYLIC SOLID SURFACE CLADDING: Providing & fixing of straight Paneling for walls & Columns structures anchored in floor slab

& celling, cladded with Acrylic Solid Surface 12mm thick sheets straight fabricated on a single face, finished in matte finish, pasted

with industrial grade silicon on a robust substrate. Substrate shall be with suitable MS box sections [Appx. 15 to 20 kg/ Sqm] as per

3.18 MR structural requirement & duly painted with anti-rust red oxide coating and covered with 12 mm thick water proof ply as per the design 72.231 SQM 12952.00 935535.91

and dimensions approved. The proposal includes the cost of preparing appropriate substrate surface over the civil structure provided,

along with material cost & installation / fixing on straight walls etc. FOR ALL WALL CLADDING, TABLE TOPS ETC. COMPLETE

Providing & supplying of Window Blinds as per the approved sample double honeycomb shades having honeycomb within

honeycomb with easy rise operating system as per following specifications fabric specifications:

• Original Non-woven honeycomb shade shaving soft fabric appearance and high energy-efficient fabric with high tear strength

constructed out of Anti-static, resilent, colour fast & Sanitized Treat 100% spun bonded non-woven polyester fiber & precision

manufacture to form a hexagonally shaped duette pleat. The Fabric is GREENGUARD certified and can attain an NRC value of 0.75.

Certificates to be provided at the time of delivery of material at site. Pleat dimension ¾ ”Honeycomb within a Honeycomb” with 3 air

pockets for maximum energy efficiency.

• Shadings are duotone, with neutral tone facing the exterior and color facing the interior The Head rail. Shall measure 50 wide and

35mm deep & thick 1.25mm extruded from alu. alloy& shall be powder coated to a smooth finish with a thickness of 40 microns.

Fabric shall be constructed from spun-bonded polyester fiber, precision manufactured to form a hexagonally shaped, dual pleat,

cellular construction. All cords & cord holes shall be fully concealed inside the fabric structure. As each of the hexagonal cells is

formed individually, pleats operate independent of each other providing superior pleat retention & structure strength. Installation

brackets. shall be of high-tension spring steel suitable for overhead & wall mounting 30mm Duette Hartford mounting bracket. Head

rail covered with Sydney Valance of height 80mm made up of Aluminium & L shape moving Rail includes “Click & Engage" method of

dimension 50mmx55mmsticked with integrated moving rail magnets provide a streamlined look, reduce centre light gap, and promote

easier operation. Polyester cord. Shall be 0.9mm in diameter & of woven hollow core end cap shall be moulded acrylic color matched

to the head & bottom rails. Bottom rail shall be a single channel section, measuring 30mm wide and 12.5mmdeep & thickness 1-

1.2mm extruded from alu. Alloy & shall be powder coated with a smooth finish to a thickness of 15-25 microns. Hold-Down bracket

(optional) shall be molded in clear acrylic. It incorporates a pin for engagement with the bottom rail end-cap. It shall be suitable for sill,

face or side facing. Cord Equalizer shall be injection melded from impact modified acrylic with a high flexural modulus

PELMET: Fabricate and install pelmet made of 19 mm thick board, up to 300 mm high and in line with external glazing as per details

of Architect. Rate to include finishing exposed surfaces of the Pelmet with 1mm laminate.

7 Digitally signed by SAKET

AAC WALL (150 MM): Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm/ 300mm thick AAC

blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying

polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement

shall be made for seperately).

3.22 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 158.73 Sqm 104.80 16634.90

13.4 12 mm cement plaster of mix :

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004,

Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives

New work (Two or more coats applied @ 1.43 litre/10 sqm) over and including priming coat of exterior primer applied @ 0.90 litre/10

12mm thick FSP HDHMR Board: Providing and fixing in wall lining, partitions etc. Confirming to ASTM E-84-2021 class1 one side

1mm decorative Lamination, having even grade low emission, high moisture resistance, fire resistance, borer, termite & fungus

3.26 MR resistance, green material and environmental friendly with necessary fixing arrangement and screws etc. , complete as per direction of

Engineer-in-Charge

12mm thick FSP HDHMR Board 50 SQM 1043.00 52150.00

5.5mm THICK FSP HDHMR BOARD: Providing and fixing in wall lining, partitions etc. Confirming to ASTM E-84-2021 class1 one side

1mm decorative Lamination, having even grade low emission, high moisture resistance, fire resistance, borer, termite & fungus

3.27 MR resistance, green material and environmental friendly with necessary fixing arrangement and screws etc. , complete as per direction of

Engineer-in-Charge

5.5mm thick FSP HDHMR Board 565.92 SQM 648.00 366716.16

ALUMINIUM FRAME: Providing and fixing partition, frame work in 50x25x1.5mm Aluminium Section placed at 600mm centre to

3.28 MR centre both ways (horizontal & vertical) fastened to floor, ceiling and horizontal member. The item includes providing and fixing 50mm 50 SQM 1347.00 67350.00

thick polyester synthetic insulation as insulation of 100 GSM.

3.29 MR WALLPAPER: Washable Vinyl Coated Wall covering as per approved make and pattern as approved by the client 390.002 SQM 1500.00 585003.00

3.30 MR 12mm thick FSP HDHMR Board: Providing and fixing in wall lining, partitions etc. Confirming to ASTM E-84-2021 class1, having even

grade low emission, high moisture resistance, fire resistance, borer, termite & fungus resistance, green material and environmental

friendly with necessary fixing arrangement and screws etc. , complete as per direction of Engineer-in-Charge

12mm thick FSP HDHMR Board 613.08 SQM 759.00 465327.72

GLASS MOSAIC TILES: Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all

colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall

surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all

operation, material and required pattern approved by Engineer-in-Charge:

TOTAL WALL FINISHING WORKS 2840027.11 16758541.47

4 MISCELLANEOUS WORKS

8 Digitally signed by SAKET

MODULAR KITCHEN - UNDER COUNTER STORAGE CABINETS:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and

sufficient number of drawers made of 18 mm thk. ISI Marked comm. ply , all ply to be laminated with 0.8 mm laminate.All shelves

should be supported on approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and

drawers fascia shall be at least 18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters

4.01 MR finished in high gloss acrylic of approved. The cabinet boxes of floor units will be supported by 100mm height vertical adjustable legs 18.9 SQM 10000.00 189000.00

which will be covered with PVC skirting in brushed aluminum finish attached by hardware of skirting. The unit shall be fixed to the

floor/ wall/slab using metal screws of appropriate size and rawl plugs. Only front face area of cabinets and skirting from floor to top of

boxes shall be considered for measurement and payment. Cabinet boxes size would be varies from 400X560X710MM to

1000X560X710MM (approx.) and join together as per site requirements etc.

MODULAR KITCHEN - OVERHEAD STORAGE WALL UNITS:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and

sufficient number of drawers made of 18 mm thk. ISI Marked comm. ply. All ply to be laminated with 0.8 mm laminate.All shelves

should be supported on approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and

4.02 MR drawers fascia shall be at least 18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters 6.3 SQM 8000.00 50400.00

finished in high gloss acrylic of approved. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and raw

plugs. Only front face area of cabinets and skirting from floor to top of boxes shall be considered for measurement and payment.

Cabinet boxes size would be varies from 400x560x710MM to 1000x560x710MM (approx.) and join together as per site requirements

4.02A MR Providing and fixing of Innotech with metal sides and quadro channels 10 Each 3548.00 35480.00

4.02B MR Providing and fixing baskets 10 Each 4013.00 40130.00

WATERPROOFING: Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C.,

kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended

proportions including rounding off junction of vertical and horizontal surface.

4.03 22.3 (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended 58.704 SQM 769.60 45178.60

proportion including rounding off junction of vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other

with bitumen @ 1.7 kg/sqm).

SLIDING & FOLDING GLASS PARTITION: Providing and Fixing EGSLDF 102 H Glass Side Sliding Folding System including, Glass,

4.04 MR Fittings,Top-Bottom track,Seal and Lock of approved make and model all complete as per the direction of Engineer-in-charge. 19.44 SQM 28186.00 547935.84

SLIDING & FOLDING ACOUSTIC PARTITION : Supply & installation of Zilio Lite system of the sliding folding partition type with the

following details. Top rail/track: top rail/track shall be proprietary supplied extruded aluminum Profile, finished in approved color

anodized finish. Above fixed Mild Steel support Structure: Mild Steel partition above sliding folding panels with 50mm thick rockwool

insulation based on the Acoustics required,finish for above support: gypsum cladding shall be provided with necessary cut-outs for

services, Mild Steel structure shall be created with the help of Anchor fastners,Box/square Mild Steel pipes attached to the true slab.

Moveable partition Panels : Panels to be filled with necessary infills for acheiving the necessary nrc levels, finished on both sides with

MDF, the panels will have retractable Top and Bottom acoustical seals for better acoustics.Panel Mounting: panels shall be mounted

over proprietary supplied Zilio Aluminium & Mild Steel, frame work as per Architect/Clients requirement.Suspension :The partition

4.05 MR panels shall be suspended on track/rails with the help of top hung mechanism.The top rail shall be fixed/suspended from the Mild 35.19 SQM 46123.00 1623068.37

Steel structure using threaded rods. Quote also to include necessary supports, cutting, finishing for the sliding folding partition panel

top rail. Parking/Stacking module: the partition panels shall be centre/parallel/side stackable type as per client's requirement.

Retractable Operation/Mechanism - Manual Handle operation by an Internal crank jack spindle mechanism. Telescopic panel -

Manual handle operation by two different internal crank jack mechanism with lever closer cut teeth gear.

ZILIO ZM - W100 Lite - Manual Suspension : 1,Track : 300.001.004,Sound Rating : 46dB,No. of Panels - 8, Total Width :

9800mm,Clear Height : 2550 mm,True Celing Height : NA,Parking Layout : Type A Center stacking,Surface : Laminate Finish

9 Digitally signed by SAKET

ACCESS PANEL: Providing & fixing Access Panel of size mentioned below having - 1. Outer aluminium frame - thickness : 1.5mm

(plus 0.2mm thick powder coating) Material : ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder

coating) Material : ENAW6063. 3. Corner fittings, inner frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc

Coating of 200g. 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of

200g. 5. 12mm plasterboard (Knauf Brand) Type: moisture resistant (MR) in green plasterboard liner. 6. Screw (self-drilling black

phosphate) - Material: mild steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock

MR (spring catch/ catch lock) - Type of lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness :

4.0mm, Length: 82mm; Material: SS2172 (cold drawn steel wire). 10. Powder coating - Color: white, RAL 9010

Wall Mounted 304 Stainless Steel Hand Dryer

1650W, 7.5A ,Voltage - AC220-240V, 50Hz ,Touch Free Infra-Red Activation, Auto cutoff - 30 Sec, 24000 RPM ,Noise Level - 70

db(A), Air Flow Rate - 95 m/s Drying Time - 7-10s, Brushless Motor, Blowing Volume - 150 m³/h, Protection Class - IPX4 ,Weight - 12

Black Open Oval Room Dustbin

4.14 MR Material- Iron + Leather ,Color - Brown ,Size - 220*255*0.4 mm , Oval Capacity - 8 Liter , Structure - Open Top , Usage/Application - 40 No 1527.00 61080

Washroom Recesses Panel 3 in 1

Paper Dispenser + Hand Dryer + Waste Bin, Material- 304 Stainless Steel (Anti - Fingerprint), Door Material- 1.2mm Stainless Steel,

4.15 MR Cabinet/ Paper/ Waste Material-0.8mm Stainless Steel, Paper Dispenser Capacity-600, C-Fold or 800 Multi Fold Paper Towel, Hand 3 No 61394.00 184182

dryer - 800-1350W (Hot & Cold Wave)Drying time -10-12 Sec, 25000 RPM, Waste Container Capacity -21 Litres, Wall Opening

required -315mm (H) x 1665mm (H) x 126mm (D)

Automatic Trash

4.16 MR Material - Stainless Steel, Color- Silver, Operation- Sensor, Battery Operated, Total Capacity- 70 Litres, Compartment- 3, Battery- 3 x 3 No 13496.00 40488

D Size Duracell (Battery not included), Size- 542x330X671mm

Standing Coat Rack With Wooden Cloth Hanger

4.17 MR Material- Stainless Steel & Wood, Color- Silver Size- 470x150x1240mm, Application- Hotel Room, Living Room, Bedroom, Home 6 No 16040.00 96240

Office, Hospital

FIRE GLASS PARTITION

Supply and installation of tested Vetrotech Saint-Gobain VDS® fully glazed fire rated fixed partition with 120 minutes of integrity and

radiation control (EW 120) with symmetrical (bi-directional) fire protection through a VDS Certified Installer. The frames shall be made

with imported cold rolled profiles. The frames are cold rolled from 1.5 mm steel sheet to form a profile of 50 mm x 50 mm on all sides.

The system shall be tested as per EN 1364-1 in an international accredited laboratory.

The glass should be CONTRAFLAM LITE (14mm) clear, non-wired, toughened, interlayered, 120 minutes fire-rated glass for integrity

and radiation control (EW 120) and insulation (I 20) with a light transmission of 86% and a sound reduction of 38 dB and

manufactured in UL & TUV audited facility and including UL-EU Certification (File number R38101) and compliant to class 1(B)1

category of Impact Resistance as per EN 12600. The glass shall be tested for 5000 hours of UV resistance as per EN ISO 12543-4.

The glass shall be EPD (Environmental Production Declaration) verified in accordance to EN 15804 and ISO 14025 in which its life

cycle assessment is performed considering Cradle to Gate system boundaries. The glass must produce a recycled content declaration

4.18 MR committing to a pre-consumer cullet of up to 11% and post-consumer cullet less than 1%. The glass shall provide bi-directional 21 SQM 59319.00 1245699

(symmetrical) fire protection.

The glass should be held in its place with the help of 1.5 mm cold rolled steel beading and Kerafix 2000 ceramic tape with cross

section of 4 x 15 mm as per the test evidence. The beading shall be clipped on using stainless steel self-tapping screws fixed at a

distance of 70 mm from the edges and 150 mm c/c henceforth. The glass panes are to be supported on non-combustible 6 mm thick

calcium silicate setting blocks. The maximum glazing size shall be as per the test certification. The profile has to be fixed to the

supporting construction by means of M10 or bigger steel bolts at every 150 mm from the edges and every 500 mm (approx.) c/c. The

partitions shall offer C4 level of wind resistance when tested as per EN12211 and shall provide class 4 level of air permeability as per

The test report will be considered valid only if it contains the stamp and signature of the authorized signatory from Saint-Gobain India

10 Digitally signed by SAKET

TOTAL MISCELLANEOUS WORKS 45178.5984 4538865.21

11 Digitally signed by SAKET

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR NO S NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR NO S NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

2023 DSR (INR) NON-DSR (INR)

Supply, Installation, Testing and Commisioning of SINGLE LEVER CONCEALED BASIN

MIXER (WALL MOUNTED) WITH SPOUT (COMPOSITE ONE PIECE BODY)

Supply, Installation, Testing and Commisioning of TABLE TOP BASIN, SIZE: 630x460x130mm

Supply, Installation, Testing and Commisioing of suitable compatible WASTE COUPLING

32MM- FULL THREAD- WITH CERAMIC CAP-*130MM HEIGHT *65MM CERAMIC CAP

Supply, Installation, Testing and Commisioing of BOTTLE TRAP (WITH INTERNAL

MR 4 PARTITION) 32mm SIZE WITH 300mm & 190mm LONG WALL CONNECTION PIPES & EACH 2 3284.00 6568.00

Supply, Installation, Testing and Commisiong of RIMLESS, BLIND INSTALLATION WALL

MR 5 HUNG WC WITH UF SOFT CLOSE SLIM SEAT COVER, HINGES AND ACCESSORIES EACH 2 15087.00 30174.00

SET, SIZE: 375X520X400 MM

MR 6 Supply, Installation, Testing and Commisiong of PNEUMATIC CONTROL PLATE EACH 2 6641.00 13282.00

Supply, Installation, Testing and Commisiong of ANGULAR STOP COCK WITH WALL

Supply, Installation, Testing and Commisiong of CONCEALED STOP COCK WITH

ADJUSTABLE WITH WALL FLANGE 15mm

Supply, Installation, Testing and Commisiong of HAND SHOWER (HEALTH FAUCET) WITH

MR 9 8mm DIA 1.2 METER LONG FLEXIBLE TUBE EACH 2 2541.00 5082.00

AND WALL HOOK ALD-CHR-573 or equivalent

Supply, Installation, Testing and Commisiong of PNEUMATIC SINGLE PIECE SLIM

MR 10 CONCEALED CISTERN BODY WITH INSTALLATION KIT & “S-TYPE” DRAIN PIPE EACH 2 8044.00 16088.00

CONNECTION SET FOR WALL HUNG WC (WITHOUT FLUSH CONTROL PLATE)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings

17.28 complete.

17.28.2 Flexible pipe

Providing and fixing mirror of superior glass (of approved quality) complete with 6mm thick

hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved

13 quality conforming to IS : 8931

18.53.1 15 mm nominal bore EACH 12 574.30 6891.60

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast

(spun) iron pipes and making good the same with cement concrete 1:3:6 (1 cement: 3 coarse

17.61 sand: 6 graded stone aggregate 12.5 mm nominal size) including necessary plaster and

pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :

18.76 Cutting holes upto 30x30cm in walls including making good the same.

18.76.1 With common burnt clay F.P.S. (non modular) bricks EACH 2 416.80 833.60

Making chases upto 7.5 X 7.5 cm in walls including making good and finishing with matching

surface after housing G.I. pipe etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the

pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step

18.7 CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

17 Internal work - Exposed on wall

Digitally signed by SAKET

18.7.2 20mm nominal outer dia pipes METRE 60 335.00 20100.00

18.7.3 25mm nominal outer dia pipes METRE 60 401.55 24093.00

18.7.4 32mm nominal outer dia pipes METRE 10 518.75 5187.50

18.7.5 40mm nominal outer dia pipes METRE 10 702.95 7029.50

18.7.6 50mm nominal outer dia pipes METRE 10 934.15 9341.50

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe

with clamps at 1.00 m spacing.

18.8 This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of

cutting chases and making good the same including testing of joints complete as per direction

of Engineer in Charge.

Concealed work including cutting chases and making good the walls etc.,

18.8.1 15mm nominal outer dia pipes METRE 30 497.80 14934.00

18.8.2 20mm nominal outer dia pipes METRE 20 537.60 10752.00

18.8.3 25mm nominal outer dia pipes METRE 10 627.25 6272.50

18.8.4 32mm nominal outer dia pipes METRE 10 739.30 7393.00

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS

19 standards and weighing not less than 690 gms.

18.51.1 15 mm nominal bore EACH 2 798.95 1597.90

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for

soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including all

neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or

without doors), reducers, WC connectors, couplers, expansion joints / bellows, cowels,

clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp &

hangers etc. in concealed / inside duct / under floor & basement ceiling / external work etc.

including chase cutting as required, excavation and back filling in all kind of soils, suspended

from floor under false ceiling or embedding the pipes laid under floors / building in 75 mm.

20 alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

MR nominal size) including cost of shuttering for proper completion of the work, breaking and

making good the walls and floors etc. after pipes have been duly laid and tested. The rubber

ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc on

50x50x5 mm slotted angle. The cost will include all support arrangements. The work includes

commissioning of all pipes lines as per drawings and specifications and as directed by engg-in-

charge at site.

a 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 80 536.00 42880.00

b 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 20 416.00 8320.00

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6

Kg/ Sqcm rating with fitting for waste pipe from fixtures to floor trap including reduces,

enlarger, socket, couplers, bends, tees etc including fixing at wall/ ceiling level supported by

MR 21 clamp & hangers etc. cutting holes in wall/ floors/ slabs and making good the same with

cement concrete 1:2:4 complete as required.

Providing & fixing UPVC Floor trap of self cleansing design with stainless steel grating

MR 22 complete in all respects.

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser EACH 8 536.00 4288.00

MR 23 Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating over floor traps. EACH 8 726.00 5808.00

Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round cover

with screws and other required fitting complete as required.

Digitally signed by SAKET

Supply, Installation, testing and commisioning of toilet waste water super quiet portable

pumping station. Pump upto vertical 5 meters and horizontal 100 meter from toilet to vertical

shaft with inlet connection in portable pump side inlet of 50, 75, 110 as per requirement to

complete the work as per the directions of engineer in charge

Providing and fixing stainless steel tray below sewage pipe of size 200x200x200 mm of grade

SS304 including all accessories

Supply, Installation, Testing and Commisiong of HIGH FLOW SINGLE LEVER CONCEALED

DIVERTOR FOR BATH & SHOWER

Supply, Installation, Testing and Commisiong of SPOUT FOR BUILT IN BATH/SHOWER

Supply, Installation, Testing and Commisiong of OVERHEAD SHOWER 350x350MM ROUND

MR 29 EDGE SQUARE HEAD SINGLE FLOW (BODY & FACE PLATE STAINLESS STEEL WITH EACH 1 24100.00 24100.00

CHROME PLATED) WITH RUBIT CLEANING SYSTEM

MR 30 Supply, Installation, Testing and Commissioning of 15 litre geyser EACH 3 12004.00 36012.00

MR 31 Supply, Installation, Testing and Commisiong of SOAP DISH HOLDER EACH 1 4392.00 4392.00

MR 32 Supply, Installation, Testing and Commisiong of TUMBLER HOLDER EACH 1 4309.00 4309.00

Supply, Installation, Testing and Commisiong of TOWEL RACK 600MM LONG WITH

MR 34 Supply, Installation, Testing and Commisiong of ROBE HOOK EACH 1 2045.00 2045.00

MR 35 Supply, Installation, Testing and Commisiong of TOILET ROLL HOLDER WITH COVER EACH 1 4978.00 4978.00

MR 36 Supply, Installation, Testing and Commisiong of TOWEL HOLDER EACH 1 3336.00 3336.00

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I.

17.10 brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and

37 making good the walls wherever required :

17.10.1 Kitchen Sink with Drain Board

Digitally signed by SAKET

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

S DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS

1.10 PVC insulated copper conductor single core cable in surface / recessed medium class

A.1 PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point

with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without

1.55 independent switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single

A.2 core cable in surface / recessed PVC conduit, and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor

A.3 1.12 single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. Metre 20000 334.00 6680000.00

mm FRLS PVC insulated copper conductor single core cable for loop earthing as

1.24 Supplying and fixing following modular switch/ socket on the existing modular plate &

switch box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 1124 122.00 137128.00

1.24.5 6 pin 15/16 amp socket outlet Each 139 197.00 27383.00

A.6 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box Each 200 40.00

excluding modular plate as required. 8000.00

1.27 Supplying and fixing following size/module, GI box along with Modular base & cover plate

on existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC

1.14 insulated copper conductor, single core cable in surface/ recessed medium class PVC

conduit as required

1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 100 233.00 23300.00

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 50 334.00 16700.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 50 439.00 21950.00

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 350 1005.00 351750.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 250 1365.00 341250.00

Supplying and making end termination with brass compression gland and aluminium

9.1 lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor

cable of 1.1 KV grade as required.

Supply of following XPLE armourned 1.1 KV grade conforming to

I.S.7098/1554Aluminium Conductor Cables :

MR Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor

armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively

(b) 3.5 C x 95 Sqmm XLPE cable RM 100 864.00 86400.00

(c ) 3.5 C x 70 Sqmm XLPE cable RM 100 680.00 68000.00

(d) 3.5 C x 50 Sqmm XLPE cable RM 100 510.00 51000.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 100 378.00 37800.00

Supply of following sizes of copper cables -PVC sheathed PVC/XLPE insulated Copper

C.3 MR conductor armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1

respectively & ISI marked.

(a) 4 C x 16 Sqmm XLPE copper cable RM 200 1446.00 289200.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 100 2253.00 225300.00

(c ) 3.5 C x 35 Sqmm XLPE copper cable RM 50 2686.00 134300.00

D.1 2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as Each 100 13.00

required. 1300.00

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit

D.2 2.10 breaker suitable for inductive load of following poles in the existing MCB DB complete

with connections, testing and commissioning etc. as required.

2.13 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel,

2.4 MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar,

D.4 neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing

etc. as required. (But without MCB/ RCCB/ Isolator)

MR 12 way (4 + 36), Double door Each 25 9081.00 227025.00

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,

2.14 residual current circuit breaker (RCCB), having a sensitivity current upto 300

milliamperes in the existing MCB DB complete with connections, testing and

D.5 commissioning etc. as required.

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

E.1 Supply, installation, testing & Commissioning of 1 module 16A SWITCH SP 1 way for Set 17 216.00

MR floor box. 3672.00

E.2 MR Supply, installation, testing & Commissioning of 2 module 16 A Socket for floor box box. Set 17 577.00 9809.00

Supply, installation, testing & Commissioning of Specific Backbox for Carpet for Floor Box

E.3 MR along with LID and TRIM for tiles/ marble 15 to 20mm thickness material for headband Set 10 12106.00 121060.00

and single cable outlet/ glavanized steel, paint RAL 7031 for floor box .

Supply, installation, testing & Commissioning of Specific Backbox for Wooden Flooring

E.4 MR for Floor Box along with LID and TRIM for tiles/ marble 15 to 20mm thickness material for Set 7 6803.00 47621.00

headband and single cable outlet/ glavanized steel, paint RAL 7031 for floor box.

E.5 Supply, installation, testing & Commissioning of flat support plate 8 module for Set 17 263.00

MR integration of Mechanism for Floor Box 4471.00

E.6 Supply, installation, testing & Commissioning of waved support plates for 4 module (2x2) Set 17 1533.00

MR modules for Floor Box 26061.00

Supplying and fixing following modular switch / socket on the existing modular plate &

E.7 1.24 switch box including connections but excluding modular plate etc. as required.

1.24.7 TV socket outlet Set 43 148.00 6364.00

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along

MR with required suitable number of GI couplers for joining raceways and fixing GI brackets

and all accessories complete in all respect as per the directions of engineer in charge

(a) 300mmx38mm(GI) - 3 compartment Mtr 150 3603.00 540450.00

E.9 (b) 225mmx38mm(GI) - 3 compartment Mtr 100 2960.00 296000.00

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to

cables at the intersection of raceways supplied completely with base and cover plates,

MR height adjustable junction box 65- 90 mm including all accessories ss plate of 3mm

E.10 thick complete in all respect as per the directions of engineer in charge

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

E.11 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the Meter 1290 47.00 60630.00

exisitng surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong with accessories

E.12 1.21 in surface/ recess including cutting the wall and making good the same incase of

recessed conduit as required

Supplying and Installation of following size perforated of painting with powder coating

4.1 M.S. cable trays of perforation of not more than 17.5% in convinient sections, joined with

E.13 connectors suspended from the cieling with MS suspenders including bolts and nuts

painting suspenders etc as required

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 100 1137.00 113700.00

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories,

F.1 5.6 and providing masonry enclosure with cover plate having locking arrangement and SET 10 13838.00 138380.00

watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as

G PANEL BOARDS

UPS Input Panel

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick

CRCA sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors

fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC

supply with rear access for cable alley and with segregated bus-bar chamber with tinned

aluminium bus bar and including supplying and fixing following switchgears, meters and

accessories, inter-connections, bonding to earth, powder coated painting and marking

as specified. Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as

detailed in the Specifications

G.1 MR Colour: Gray Powder Coated, as per approved sample.

1 nos, 250 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault

breaking capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 320 Amps capacity with heat shrinkable colored

sleeves and I/C DMC/SMC bus bars supports at required intervals complete for cross

section, size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB - 2 Nos.

(b) 200 Amps, TPN, MCCB - 1 nos

(c ) 100 Amps TPN MCCB - 1 nos

Panel complete as above Each 1 ######## 200000.00

G.2 MR Floor Panels

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick

CRCA sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors

fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC

supply with rear access for cable alley and with segregated bus-bar chamber with tinned

aluminium bus bar and including supplying and fixing following switchgears, meters and

accessories, inter-connections, bonding to earth, powder coated painting and marking

as specified. Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as

detailed in the Specifications

Colour: Gray Powder Coated, as per approved sample.

1 nos, 250 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault

breaking capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 320 Amps capacity with heat shrinkable colored

sleeves and I/C DMC/SMC bus bars supports at required intervals complete for cross

section, size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB - 4 Nos.

(b) 40 Amps, TPN, MCB - 10 nos

Panel complete as above Each 1 ######## 200000.00

G.3 MR UPS Output Panel

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick

CRCA sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors

fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC

supply with rear access for cable alley and with segregated bus-bar chamber with tinned

aluminium bus bar and including supplying and fixing following switchgears, meters and

accessories, inter-connections, bonding to earth, powder coated painting and marking

as specified. Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as

detailed in the Specifications

Colour: Gray Powder Coated, as per approved sample.

One (1) nos, 200 Amps. 4 pole MCCB and 2 nos. 63 Amps 4P MCCB, i.e four pole

Moulded Case Circuit Breaker of fault breaking capacity 25 KA (ICS=ICU up to 433 V)

complete in all respect

TPN aluminum bus bars of minimum of 320 Amps capacity with heat shrinkable colored

sleeves and I/C DMC/SMC bus bars supports at required intervals complete for cross

section, size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

2 Nos. 100A, 4P, MCCB (25kA) with phase indicating lamp protected with 2A, SP, MCB's

along with E/M interlocking

(a) 63 Amps, TPN, MCB - 4 nos

(b ) 40 Amps, TPN MCB - 10 nos

Panel complete as above Each 1 ######## 314297.00

H SAFETY ITEMS

Providing and fixing MV danger notice plate of 200mm x 150mm made of mild steel,

H.1 2.21 atleast 2 mm thick, and vitreos enamelled white on both sides and with iscription in Nos. 6 269.00 1614.00

single red colour on front side as required

Providing and fixing HT danger notice plate of 250mm x 200mm made of mild steel,

H.2 2.22 atleast 2 mm thick, and vitreos enamelled white on both sides and with iscription in Nos. 2 292.00 584.00

single red colour on front side as required

I MR UPS SYSTEM

Supply, Installation, Testing and Commissiong of Hot-swappable Modular Type 60 KVA

(3 no 20 kva module + 1 no of 20 kva redundant module)True Online Double Conversion

UPS 3Phase Input - 3Phase Output UPS having granular Architecture. Module size

should be 20 kVA or below with multi controller. IGBT Based Rectifier and IGBT Based

Inverter Batteries:12 V, SMF Amararaja/Exide with minimum VAH capacity of 48000 Nos. 1 ######## 1834851.00

suitable for 30 minutes backup with each ups Along with Accessories Rack, Interlinks,

SFU, Parallel Kit, DC Cable Upto 5 Meters complete in all respect as per the directions of

the engineer in charge. UPS should have availability of Input /Output isolator, Inbuilt

manual bypass along with phase sequence corrector. UPS Efficiency shall not be less

Total of Electrical items 10941958.00 6656862.00

15 Digitally signed by SAKET

SCHEDULE OF QUANTITIES - HVAC WORKS

DSR HVAC TOTAL TOTAL

S No 2019/DSR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

EM 2018 DSR (INR) NON-DSR (INR)

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant

Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating,

having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors

for above 14 HP modules, microprocessor based Controller, top discharge type condensing

unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as

1 1.0 required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C per HP 10 16415.00 164150.00

ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3

Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and

ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not

less than 6.5 .

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High

wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low

noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil,

electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary

3 3.0 accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply,

complete as required. The unit shall have automatic force shut down provision in case of fire on

receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet

conditions of 27 Degree C DB and 19 Degree C WB temperature.

Lifting, Shifting, Supply, Installation, Testing & Commissioning of Interconnecting "Y" & "T"

4 4 Joints i.e. Refnet Joints/ Header with Insulation for refrigearnt piping

Refrigerant Piping

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing

of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system,

5 5 complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing

including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell

elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for

Suction and Liquid lines, all accessories as per specifications etc. as required :

5.1 5.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 40 245.00 9800.00

5.2 5.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 40 331.00 13240.00

5.3 5.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 40 466.00 18640.00

5.4 5.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 40 588.00 23520.00

5.5 5.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 75 707.00 53025.00

5.6 5.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 75 865.00 64875.00

5.7 5.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 50 1022.00 51100.00

5.8 5.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 50 1108.00 55400.00

6 1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit

Supply,installation,testing and commissioning of PVC drain water with necessary clamps,

8 MR fittings such as bends tees etc. and duly insulated.

40 mm dia (9 mm tick ins.) Rm 80 374.00 29920.00

Total HVAC WORKS 637652.00 86784.00

Digitally signed by SAKET

SCHEDULE OF QUANTITIES - HVAC WORKS

DSR (E & M- Non DSR

S NO DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT

2022)/ MR AMOUNT

VAV BOX (WITH INTEGRAL SOUND ATTENUATOR)

Supply and Installation of pressure independent rectangular VAV unit with integral sound attenuator

made of 22G GI sheet casing length 900mm consisting of 25mm thick 48kg/m3 density fiber glass wool

covered with tissue paper ,elliptical volume control damper , calibrated differential pressure sensor (DPT

sensors) at inlet complete with digital Thermostat.(All VAV shall be factory calibrated).

Supply, installation, testing and commissioning of Variable Frequency Drive (VFD)

2.0 MR 380-400 VAC, IP-54 Chassis, RFI class A1 (C2), No brake chopper.

a VFD upto 35 HP or as directed by the engineer in charge Nos. 2 180000.00 360000.00

DUCT PRESSURE SENSORS

Supply, Installation and Testing of pressure sensors to be installed in supply air ducts. Quoted

3.0 MR price shall be inclusive of necessary conduting, copper control cabling from the sensors to the respective Nos. 8 17500.00 140000.00

VFDs as per "Approved Shop Drawings".

Supply, Installation, Testing & Commissioning of Silent type circular /rectangular inline fans for exhaust

air complete with sheet metal casing, 25mm thick acoustic insulation, direct driven centrifugal fan, motor

with proper protection and inspection door. Fan shall be suitable for operation on 220+6 % volts, 50

Hz,1 phase AC power supply. Flanges to be provided on both sides to facilitate duct connections. Fan

4.0 shall be installed as shown in the drawings and will be of following characteristics:

MR All single phase inline fans shall be provided with factory fitted speed regulators. All Fans Should be

complete with Plug Top & necessary power cable.

Fans shall have low noise level in rage of 35-40dBA @3m and shall be suitable for indoor installations.

a 200 CFM S P of 13-14 for Toilet Nos. 4 6449.00 25796.00

5.0 Tube Axial Fan

Supply Installation, testing and commissioning of supply air Tube Axial flow fan of following capacity

with GSS casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller

directly driven by TEFC induction motor suitable for 3 Phase 50 Hz 415 V ± 10 %, complete as required.

a MR This cost shall include the cost for suitable panel, DOL starter, breakers etc compete in all respect as

per the directions of engineer in charge.

9000 cfm at 15 mm static presuure for fresh air/exhaust air With Class "H" insulation. NOS 6 143910.00 863460.00

Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch and return air

path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring

return so as to close the damper in the event of power failure automatically and open the same in case

6.0 16.20 of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted.

The damper shall also be closed in the event of fire signal complete as required and as per

specifications.

(Fire damper shall ve suitable for 120 minutes fore rating as per NBC norms)

GI Gravity Louver

7.0 MR Supply, installation, testing and commissioning of GI Gravity Louver complete with neoperene rubber

gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

8.0 VOLUME CONTROL DAMPER

MR Supply, Installation and Testing of GI box type volume control dampers as per the specifications and

a shop drawings. SQM 15 5900.00 88500.00

- For Rectangular Ducts

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/

round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers,

9.0 16.12.1 supports etc. as per approved drawings and specifications of following sheet thickness complete as

d 16.12.1.4 Thickness 1.25 mm sheet SQM 50 1836.00 91800.00

Diffusers & Grills

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control

dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume

control dampers complete as required

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium

volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without

volume control dampers with anti smudge ring & removable core.

Supply, Installation, Testing of 125mm deep antivibration flexible joints at the outlet of air handling

14.0 MR units/ductable split units//inline fans. Flexible connections shall be constructed using imported fire RM 100 1440.00 144000.00

retardant fabric with extruded aluminium frame/flange on both sides of approved make.

Supply, Installation, Testing and Balancing of linear slot diffusers as per the approved shop drawings

and specifications. Each slot shall be 25mm wide. The diffuser face shall be a one piece extrusion so

there are no visible joints. Slot diffusers shall be complete with end caps either as end plates or end

angles or integral part, air control blades etc. Slot diffuser have a variable neck length and the diffuser

15.0 MR face could be optionally be fitted to the plenum box on site. Diffuser shall have provision to access collar

dampers for air balancing.

All Return air diffusers in false ceiling to be properly supported from real slab using chains or gripple

3 slot/2slot, powder coated extruded aluminium diffusers of approved colour & shade. SQM 10 12500.00 125000.00

Supply, Installation and Testing of Bird Screens with GI wire mesh to be installed at the suction of fresh

16.0 MR air/discharge of Exhaust air as per the specifications and shop drawings. Sample of bird screen to be SQM 10 5436.00 54360.00

got approved from consultants and Clients prior to procurement.

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile

rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints

17.0 16.23 shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as

per specifications and as required.

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass

wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to

18.0 16.21 centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed SQM 10 708.00 7080.00

to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as

required and as per specifications

Supply, Installation, Testing and Commissioning of Air Purification systems in the specified areas where

AHU/VRF/FCU/Cassette/Hi-Wall/Ductable units etc are installed, so as to improve indoor air quality by

using, Self-cleaning Needlepoint Ionizer made of Carbon brush emitters. The Needlepoint brushes shall

be designed to properly release equal amount of positive and negative ions in the supply air,>400Million

ions/cc without any obstruction. The units to be suitable for capacities up to 6000 CFM, with universal

19.0 voltage input 24V to 240V AC/DC, ionizer indicator LED, set of dry contacts which will indicate ionizer

MR functionality. The unit shall have capability to be switched on 24/7 and shall have weathertight conduit of

minimum 6ft length.System should kill microorganisms and pathogens and backed with Independent lab

test reports on the real virus and not surrogate. The system also should reduce odors, TVOC’s and

reduce particle/particulate matter/PM2.5/PM10. The products should be UL 2998 listed with zero

Ozone Emission.

Smart Indoor Air quality monitor to measure Air quality parameters including AQI, PM1, PM2.5, PM10,

CO2, Humidity and Temperature. In addition to the mentioned sensors of the base device, you can

customize it to measure more parameters by adding extra sensors. This monitor should be a 3-tier

architecture including sensor Hardware, secure cloud infrastructure, monitoring apps including

dashboard, android/IOS apps, where ever requires. Dashboard should be customisable and IOT

20.0 MR (Internet of things) enabled with view and management for all of your locations on one dashboard so that

you can easily identify and address any air quality issues. Sensors should be soft calibratable. The

System should be capable of providing periodic Preventive maintenance for automated after sales

support service in form of notification/ alerts and user interaction through dashboard application.

Air Quality Monitor Nos 1 7580.00 7580.00

Supply, installation testing and commissioning of Router / Supervisory Controller which will manage the

VAV information and communicates on BACnet®/ LONWORKS® protocol to monitor and Control the

VAVs from BMS software on PC in accordance with the approved shop drawings and technical

specifications. Connecting the final daisy loop from all VAV to Supervisory Controller shall be part of the

21.0 MR scope. The communication between Supervisory controller and BMS software in PC should be on IP. Nos 1 218928.00 218928.00

Cost include powder coated Panel for Supervisory Controller of required size with 24 Volts provision

which includes power cable, plug, transformer and with all necessary accessories for mounting on wall

in accordance with the approved shop drawings and technical specifications.

Supply, Laying, Termination of ISI Certified 2 Core 1.0 sq.mm ATSC, FRLS,PVC insulated, Unarmored,

Tinned Copper, twisted, shielded, PE insulated, VAV Communication Cable with proper ferrules, lugs

22.0 MR and other necessary accessories. The spec shall meet the system manufacturer specifications. Rmt 500 120.00 60000.00

Supply, Laying, Termination of ISI Certified 4 Core 1.0 sq.mm ATSC, FRLS ,PVC insulated, Unarmored,

Tinned Copper, twisted, shielded, PE insulated, VAV Communication Cable with proper ferrules, lugs

23.0 MR and other necessary accessories. The spec shall meet the system manufacturer specifications. Rmt 400 280.00 112000.00

Supply & Laying of ISI Certified 1" dia PVC Conduit with bends, collar, saddles, saddle base and other

accessories for Signal Cable / DDC Communication Cable

TOTAL HVAC WORKS 3558044.0 3948652.0

Digitally signed by SAKET

SCHEDULE OF QUANTITIES: IT

TOTAL TOTAL AMOUNT

TOTAL TOTAL AMOUNT

S No Description UNIT QUANTITY RATE

A. UTP Components for Data DSR (INR) NON-DSR (INR)

Supply, Fixing & Laying of CAT 6A UTP cable 23 AWG solid copper

1 conductors for Connectivity of Hub room to End Point.High Speed Gigabit Mtr 29300 72.00 21,09,600.00

Ethernet U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH Cable, C6

Supply, Installation, Testing and Comissioning of I/O port for CAT6A cable

termination at Work Station end. Keystone Unshielded Outlet, 180DG C6

Supply , Installtion , Testing and Comissioning of CAT6A patch cord 2 Mtr

3 (7 feet) for information outlet (I/O) to end user device connectivity.High Nos. 586 350.00 2,05,100.00

Speed Gigabit 24AWG U/UTP Patch Cord, LSZH, C6

Supply, Installation, Testing and Comissioning of CAT6A patch cord 1 Mtr

4 (3 feet) for information outlet (I/O) to Rack End Redantant device Nos. 586 279.00 1,63,494.00

connectivity.High Speed Gigabit 24AWG U/UTP Patch Cord, LSZH, C6

Supply, Installation, Testing and Comissioning of 24 port Loaded Jack Panel

for CAT6A cable termination at rack end. Data Active

Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper

6 conductors for Connectivity of Hub room to End Point.High Speed Gigabit Mtr 10400 38.00 3,95,200.00

Ethernet U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH Cable, C6

Supply, Installation, Testing and Comissioning of I/O port for CAT6 cable

termination at Work Station end. Keystone Unshielded Outlet, 180DG C6

Supply, Installation, Testing and Comissioning of 24 port Loaded Staggred

Jack Panel for CAT6 cable termination at rack end. Voice Active

Supply, Installation, Testing and Comissioning of CAT6 patch cord 1 Mtr (3

9 feet) for information outlet (I/O) to end user device connectivity. (Rack end), Nos. 208 235.00 48,880.00

High Speed Gigabit 26AWG Patch Cord, LSZH, C6

Supply, Installation, Testing and Comissioning of CAT6 patch cord 2 Mtr (7

10 feet) for information outlet (I/O) to end user device connectivity.High Speed Nos. 208 275.00 57,200.00

Gigabit 24AWG U/UTP Patch Cord, LSZH, C6

Supply, Installation, Testing and Comissioning of 2 Port British Style

Shuttered Face Plate white for I/O fixing at user side

Supply, Installation, Testing and Comissioning of 24 port Loaded Staggred

Jack Panel for CAT6 cable termination at rack end. Riser Active

Supply, Installation, Testing and Comissioning of 400 pair MDF box

complete with Krone Modules

14 Supply, Installation, Testing and Comissioning of 50 pair riser cable Mtr 200 600.00 1,20,000.00

C. Backbone Component

Supply , Installtion , Testing and Comissioning of 6 core OM3 Multimode

Supply , Installtion , Testing and Comissioning of OS2 G.652.D 1-fibre,

buffered, LC Duplex, LC to pigtail, 1m.

Supply , Installtion , Testing and Comissioning off Rack mount fibre tray

17 supporting 6 way configuration in LC Duplex. Panel should be loaded with 6 Nos. 2 25,624.00 51,248.00

port LC duplex adaptor panel

Supply , Installtion , Testing and Comissioning off Rack mount fibre tray

18 supporting 24 way configuration in LC Duplex. Panel should be loaded with Nos. 1 44,841.00 44,841.00

24 port LC duplex adaptor panel

D. Network Rack and Other Accessories

SITC of 42U 800x1000 Server Rack with perforation, Glass Door, Cable

19 managemenet, 6/16A power strips- 2 nos, Castors, 4 fan for cooling, Rack Nos. 2 80,000.00 1,60,000.00

should have shelves - 4 nos

SITC of router with Aggregate Throughput (Default) 200mbps, Aggregate

Throughput (Performance License) 500Mbps, Total onboard WAN or LAN

10/100/1000 ports 4nos, RJ-45-based ports 4nos, SFP-based ports 4nos,

20 NIM slots 3nos, Default memory DDR3 ECC DRAM (data plane) 2gb, Nos. 1 6,90,104.00 6,90,104.00

Maximum memory DDR3 ECC DRAM (control/servic es plane) 16gb,

Default flash memory 8gb, USB console port -type B mini (up to 115.2 kbps)

SITC of L2/L3 Server Farm switch with 8 x 10G RJ45 + 8 x 10G SFP+

Layer 2 switching, VLAN support, Spanning Tree Protocol (STP), advanced

21 threat protection, IPv6 first-hop security, quality of service (QoS), sFlow, Nos. 1 18,57,718.00 18,57,718.00

dynamic routing. Switching Capacity 320 Gigabits per Second (Gbps,

Capacity 238 Millions of Packets per Second (mpps) (64-byte packets)

SITC of L3 Managed Switch with 24X 10G ports and 4x 10G/1G fixed

uplinks interface. Distribution Switch shpuld have minimum 16GB Flash

memory, Advanced switching capabilities BGP, EIGRP, HSRP, IS-IS, BSR,

22 MSDP, PIM SM, PIM SSM, BIDIR-PIM, IP SLA, OSPF. VRF, Software- Nos. 1 11,40,255.00 11,40,255.00

Defined Access (VXLAN, LISP, SGT), MPLS, mVPN 3 years warranty

support for Access Switches.

SITC of Access Switch with minimum of 48x10/100/1000 Base-T ports, 4x

10 Gig SFP+ ports for uplink ports(supporting Single mode & Multi mode

1G/10G (LX, LR, SX & SR modules). Should have Non-blocking switch

fabric, IPv6 Ready 3 years warranty support for Access Switches.

SITC of Inbuilt controller managed 2*2:2 Indoor Wi-Fi 6 (802.11ax) Access

SITC of 24 port POE Access Switch with minimum of 24X 10/100/1000 Base-

T POE ports, 4x 10 Gig SFP+ ports populated for uplink ports (supporting

25 Single mode & Multi mode 1G/10G (LX, LR, SX & SR modules). Should Nos. 6 2,56,237.00 15,37,422.00

have Non-blocking switch fabric, IPv6 Ready with 3 years warranty support

for Access Switches.

26 SITC of 10 Gig SR transceivers/equivalent LC connector MM Nos. 38 32,030.00 12,17,140.00

27 SITC of 1 Gig SR transceivers/equivalent LC connector MM Nos. 4 15,374.00 61,496.00

18 Digitally signed by SAKET

S No Description UNIT QUANTITY RATE

IP BASED CCTV SYSTEM DSR (INR) NON-DSR (INR)

Supply, Installation, Testing & Commissioning of CCTV Camera - 5MP IR Network Dome

Camera - 30Mtr.

1/2.7” 5MP PS CMOS Image Sensor (0.9407centimetres)

Instastream and Smart H.264+ dual-stream encoding

1 DWDR, Day/Night (ICR), 3D-DNR, ROI, AWB, AGC, BLC, HLC Nos 10 12645.00 126450.00

3.6mm lens (2.8mm optional)

IR Range of 30 Mtrs, IP67, PoE

Support Built-in Mic

CMS Software:PCAPP

Supply, installation, testing and commissioning of Video Management software

enabling security related personnel to easily and remotely gather video evidence, monitor

live situations, and configure and maintain a video surveillance system over Ethernet

consisting of digital video recorders (DVRs), hybrid digital video recorders, network video

2 recorders (NVRs), analogue video cameras, and IP video cameras should support Nos. 1 160000.00 160000.00

Detachable Viewers –users have the ability to detach Viewer panels and move them to

other (or the same) monitor(s). A maximum of two (2) Viewers can be detached for a total

of 75-up video tiles [two (2) detached and one (1) core Viewer.

Supply Installation Testing & Commissioning of 43 inch Full HD LED monitor including wall

mount brackets/ clamps/ desk mounting stand.

4 Supply and fixing of RJ45 Connector Nos. 20 26.00 520.00

Supplying and fixing in position GI box for data outlet suitable for fixing of RJ 45 face plate

complete as required.

Supply & Fixing of PCB based Information Outlet (I/O) RJ45, TIA-568C Category-6,

Termination of Catergory-6 UTP Cable, UL listed, Shall conform to Category-6 as per the

EIA/TIA-568C.2, Shall support network line speeds up to 1 Gbps, Shall have RJ-45 type

connector with bend limiting and strain relief boot for securing IDC contacts from external

6 forces and for maintaining the bend radius of the cable, Shall have minimum durability of Nos. 10 240.00 2400.00

750 mating cycles and 200 termination cycles. Shall be certified by independent labs

like ETL/GHMT for compliance to EIA/TIA-568C.2. The outlet shall be fixed in existing box

& cover plate in wall/furniture/floor complete as required.

Supply & Fixing of Single Faceplate, Single Port (RJ45-DATA) square plate having spring

7 shuttered front access for preventing ingress of dust, dimension as per commercially Nos. 10 80.00 800.00

available modular office furniture.

Supply & Laying in existing conduits/raceway/furniture of 4-pair Unshielded twisted pair

cable with a cross filler (+), meeting Category 6 standards as per TIA-568C.2. The cable

shall be tested till 600 MHz or more from independent laboratories like ETL for 4

connections. Test Certificate from independent labs like ETL shall be required.

Supply & Fixing of UTP Jack Panel UL listed, loaded with 24 no's UTP ports for PCB based

IO Jacks (RJ45, TIA-568C Category-6), having integrated bonding bar or other

mechanism for grounding, loaded with individually replaceable 24 nos. Category-6 I/O

9 Jacks complying with TIA-568.C.2. Shall be 6 port module construction for better cable Nos 1 8000.00 8000.00

dressing at the rear. The jacks shall have RJ-45 type connector with bend limiting and

strain relief boot for securing IDC contacts from external forces and for maintaining the bend

radius of the cable.

Supplying & Fixing of Category 6, UTP patch cords constructed of 24 AWG

unshielded twisted pair stranded copper cable with an enhanced performance modular plug

10 at each end. Patch cord cable shall be offered in multiple coloured UTP cable for design Nos. 10 235.00 2350.00

flexibility with a clear strain relief boot on each modular plug. All patch cords shall be

compatible with both T568A and T568B wiring schemes. UTP Cable, 2 Meter.

Supplying & Fixing of Category 6, UTP patch cords constructed of 24 AWG

unshielded twisted pair stranded copper cable with an enhanced performance modular plug

11 at each end. Patch cord cable shall be offered in multiple coloured UTP cable for design Nos. 10 275.00 2750.00

flexibility with a clear strain relief boot on each modular plug. All patch cords shall be

compatible with both T568A and T568B wiring schemes. UTP Cable, 1 Meter.

SITC of Access Switch with minimum of 24 nos. 10/100/1000 PoE Ethernet Ports with 4

SFP Uplinks and total for 28 Ports , it should support Full Duplex Switching

19 Digitally signed by SAKET

SCHEDULE OF QUANTITIES - LIGHTING WORKS

S NO DSR/MR Description Image Unit QTY Rate DSR AMOUNT NON DSR AMOUNT

Supply, Installation, Testing and Commissioing of Recessed downlightwith HPE (High-

Performance Efficiency) with LED (Light Emitting Diode), system power: 12 W,

Luminous flux of luminaire 1320 lm, 110 LM/W system efficacy, Colour temperature of

4000 K, Neutral white, CRI > 80, 230V constant current driver, 70% of luminous flux

2 MR after 50,000 operating hours; energy-efficient LEDs, direct light emission, housing in die- no 58 1394.00 80852.00

cast aluminium, Polyester powder white coloured coat applied over a 5-stage pre-

treatment trim, prismatic diffuser for homogenous light distribution, ZHLS (ZERO

HALOGEN LOW SMOKE) wiring, Electronic control gear, Protection class II, IP 40, Ø

Pendent luminaire with HPE (High Performance Efficiency) LED (Light Emitting Diode),

system power: 28W, Luminous flux of luminaire 3080 lm, 110 LM/W system efficacy,

colour temperature of 4000 K, neutral white, CRI > 90, THD<5%, SDCM 3, 230V

constant current driver, 70% of luminous flux after 50,000 operating hours, Energy

3 MR efficient LEDs, Direct light emission, Luminaire profile in aluminium, Polyester powder no 234 4001.00 936234.00

aluminium white coloured coat applied over a 5- stage pre-treatment, opal prismatic

diffuser for a homogenous light distribution ZHLS(ZERO HALOGEN LOW SMOKE)

internal wiring, integral electronic control gear, Protection class I, IP 40, L = 1175 mm,

Supply, Installation, Testing and Commisioning of Recessed luminaire with LED (Light

Emitting Diode), system power: 28 W, luminous flux of 2800 lm, colour temperature of

4000 K, Neutral white, 230 V constant current driver, 70% of luminous flux after 50,000

operating hours, energy-efficient LEDs, CRI > 80, CRI > 80, THD<5%, P.F>0.95,

4 MR SDCM 3, direct light emission, Luminaire housing in Aluminium Extrution, polyester no 25 2800.00 70000.00

white powder coat applied over a 5-stage pre-treatment, Opal diffuser for glare-free

uniform light, integral electronic control gear, Protection class I, IP40, L = 595 mm, B =

Recessed with trim luminaire Pinspot light with LED(Light Emitting Diode) system

power: 5W, luminous flux of luminaire 400lm, colour temperature of 4000K, Neutral

white, CRI>90, 230V constant current driver, 70% of luminous flux after 50,000

5 MR operating hours, direct light emission, aluminium housing with trim, polyester White no 30 1200.00 36000.00

powder coat applied over a 5 stage pre-treatment on trim, with lens and a beam angle

of 24° and external electronic control gear, Protection class II, IP20

Recessed with trim luminaire Pinspot light with LED(Light Emitting Diode) system

power: 8W, luminous flux of luminaire 640lm, colour temperature of 4000K, Neutral

white, CRI>90, 230V constant current driver, 70% of luminous flux after 50,000

6 MR operating hours, direct light emission, aluminium housing with trim, polyester White no 80 2400.00 192000.00

powder coat applied over a 5 stage pre-treatment on trim, with lens and a beam angle

of 24° and external electronic control gear, Protection class II, IP20,

STRETCHED FABRIC CEILING: Supply & installationof fabric false ceiling / wall

formed out with TRANSLUCENT Printed fabric coverings made out of polyester knitted

fabric coated with Polyurethane (PU). The TRANSLUCENT Printed fabric width of 2m,

3m, 4.1m &5.1m with weight of 200gm/m2, thickness of 0, 3 mm. The appearance of

fabric is matt, smooth and uniform with blanq color and light transmission of 50%. The

tear strength of fabric should be accordance to CH: 4,5daN; TR: 6,5 daN. The fire rating

should be accordance to B-S1, d0. The fabric should be humidity resistant and free of

carcinogenic substances(CMR) or volatile organic Compounds (VOC’s). At labeling in

accordance with the French decree no. 2011- 321, Oeko-Tex standard100 certified.

Fabric should be installed with approved manufacturer guidelines. It comes with 10-

year manufacturer guarantee. The installation of TRANSLUCENT Printed fabric should

7 MR be dry installation & done at room temperature using CLIPSO PVC, ABS Grippers. Sq Meter 82.08 8635.00 708760.80

Clipso ceiling base to be made of MS or Wooden frame finishing to a flush finish of

tapered and square edges in desired design as per architect specification.Supply of

LED Lights behind the Fabric Wall/ False ceiling in modules/ PCB with recommended

wattage as per manufacturer's standards to give an effect of ambient lighting. LED

make MLS/ Bridgelux / Osram- SMD 2835, LED spacing / Pitch should be atleast 73 -

80mm with beam angle of 170 degree, Colour temperature shoud be as per design

intent 3000K/4000K/6000K. Wattage of 8-10W/mtr. LED modules/ PCB should be

positioned properly to provide an even light flow, casting noshadows or dark spots. LED

Driver Cost included.

Supply, Installation, Testing and Commisioning of Pendant customised luminaire with

HE-High Efficiency LED (Light Emitting Diode) system power: 12 W/Mtr, the luminous

flux of luminaire 960 lm, color temperature of 4000 K, CRI > 90, SDCM<3, THD<10%,

230 V constant current driver, 70% of luminous flux after 50,000 operating hours, direct

8 light emission, luminaire profile in aluminium, black powder-coated, opal diffuser for Mtr 20 30,000.00 600000.00

uniform illumination, Electronic control gear.

Protection class I, IP20

L = 1000 mm, B = 55 mm, H = 75 mm, PL max = 1500 mm (one customised

suspended Ring type fixture of 3800mm Diameter respectively)

Supply, Installation, Testing and Commisioning of Round Ring shaped Suspended

mounted LED Ceiling luminaire with Downlight distribution with Ring shaped Diffuser

having system power: 70W, Luminous flux of luminaire 7000lm, direct light emission,

CRI > 80, 230V constant current driver, 70% of luminous flux after 50,000 operating

hours, energy efficient LEDs with Dia. (Ø) 1200mm with Opal PC/PMMA diffuser for

9 MR homogenous uniform, soft and glare free light distribution, luminaire housing profile in Each 12.00 28782.00 345384.00

extruded aluminium with efficacy of 100Lm/W, Power Factor of more than 0.90 & CCT -

4000K/5700K, Powder coated White/Black coloured, Internal wiring along with Integral

Electronic Driver having an in built Surge Protection of 2.5kV, Adjustable wire

suspension, Protection class I, IP20.

Supply, Installation. Testing. Commissioning of Recessed magnetic track, aluminium

support profile, polyester powder coated Black applied over a 5 stage pre-treatment,

10 MR IP 20 including all accessories and connectors Each 474.60 4500.00 2135700.00

L = 1000 mm, B = 96 mm, H = 80mm, cutout width = 55 mm.

Supply, Installation. Testing. Commissioning of LED Track Mounted Linear Diffused

10W Efficacy: 80lm/w Lumen: 1600 CRI :>90, Color Temperature: 4000K, SDCM 3,

11 MR Life Time: L70 50000Hrs 230V, Light Throw: Direct light emission Material, Aluminium Each 215.00 4500.00 967500.00

Optics: Opal Diffuser, Finish: Black Control Gear: Electronic control, Protection Class: II

Supply, Installation, Testing, Commissioning of LED Pendant round decorative fixture

made of glass, 15W, Efficacy: 70lm Lumen: 1050 CRI :>80 Color Temperature: 3000K

12 MR SDCM 3 Life Time: L70 50000hrs 230V Light Throw: Circular light emission Material: Each 20.00 8500.00 170000.00

Glass Optics: Opal Diffuser Finish: White Control Gear: E27 Holder with lamp,

Protection Class: II IP 40 Dia:200mm H: 200mm IP 40

Supply, Installation, Testing, Commissioning of Surface Mounted luminaire Super Slim

with LED(Light Emitting Diode) system power: 15W, luminous flux of luminaire 750lm,

colour temperature of 4000K, CRI>90, constant voltage driver, energy efficient LEDs,

13 MR direct light emission, profile in aluminium, Anodized, Opal diffuser for uniform Each 192.00 3500.00 672000.00

illumination, external DALI control gear

Protection class II, IP20

LED Pendant 12W Efficacy: 90lm Lumen: 1080 CRI :>80 Color Temperature: 4000K,

CRI > 90, SDCM<3, THD<10% Life Time: L70 50000Hrs 230V Light Throw: Direct

14 MR light emission Material: Aluminium Optics: Finish: White Control Gear: Electronic

Control Protection Class: I IP 20 Dia:75 mm H: 257mm, IP 20

20 Digitally signed by SAKET

SCHEDULE OF QUANTITIES - FIRE ALARM

DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

2022 DSR (INR) NON-DSR (INR)

SITC of UL268 6th and 7th edition compliance and FM approved Intelligent Addressable multi-

criteria detector (optical and thermal sensors) complete with standard base, facility to mount in

different comprehensive environment, Tri-color detector-status LED with 360 ° view,

microprocessor circuitry with error check; detector self-diagnostics and supervision

programs,Rate-of-Rise Detection: 15°F / min. (8.3°C / min.) - Fixed: 135°F (57°C) , Field

1 MR programmable as rate-of-rise or fixed temperature, Polarity insensitive, Superior EMI and RFI No 149 3175.00 473075.00

immunity, RoHS compliant. Detector shall have in-built isolator for better reliability, circuit

integrity and advanced fault finding. Manufacturers not having in-built Isolator feature in

detector shall consider Isolator base in place of standard base OR separate Isolator before and

after every detector to comply the same without any extra cost. It shall be

includesurface/recessed MS Box complete with all connections etc as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS

Box having two LED, metallic cover complete with all connections etc as required.

SITC of UL Listed and FM approved Intelligent Addressable Rate of Rise and Fixed

temperature detector complete with standard base, Seven (7) field-selectable settings in a

temperature range of 135°F – 174°F (57.2°C – 78.9°C) , a low-temperature warning of 40°F

(4.4°C), facility to mount in different comprehensive environment, Tri-color detector-status LED

with 360 ° view, microprocessor circuitry with error check; detector self-diagnostics and

3 MR supervision programs, Field programmable as rate-of-rise or fixed temperature, Polarity No 4 3028.00 12112.00

insensitive, Superior EMI and RFI immunity, RoHS compliant. Detector shall have in-built

isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not

having in-built Isolator feature in detector shall consider Isolator base in place of standard base

OR separate Isolator before and after every detector to comply the same without any extra

Supplying, installation, testing & commissioning of fault isolator complete with base as

SITC of UL Listed Sounder cum Strobe rated at 75 dBA @ 3m for Audible annunciation and

75cd flashintg at 1 Hz for visual indication.

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Control

Module with built in dual isolator, polarity insensitive, Tri color LED for status (Green for

Normal,Yellow for Faulty and RED for activation), Operating Temp and RH: 0-49degC and

6 MR <=95%. Module shall have in-built isolator for better reliability, circuit integrity and advanced No 3 3753.00 11259.00

fault finding. Manufacturers not having in-built Isolator feature shall provide separate

Isolator before and after every Module to comply the same without any extra cost. (For

AHU & Staircase Pressurization Fans, Hooters / Sounders / Strobes etc.)

Supplying, installation, testing & commissioning of addressable phone control module

complete as required.

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Monitor

Module with built in dual isolator, polarity insensitive, Tri color LED for status (Green for

Normal,Yellow for Faulty and RED for activation), Operating Temp and RH: 0-49degC and

8 MR <=95%. Module shall have in-built isolator for better reliability, circuit integrity and advanced No 3 2950.00 8850.00

fault finding. Manufacturers not having in-built Isolator feature shall provide separate

Isolator before and after every Module to comply the same without any extra cost. (For

Flow Switch Monitoring/ Gass suppresion Integration etc.)

SITC of UL268 6th and 7th edition compliance and FM approved Intelligent Addressable

Duct detector with 10ft sampling pipe (optical and thermal sensors) complete with standard

base, facility to mount in different comprehensive environment, Tri-color detector-status LED

with 360 ° view, microprocessor circuitry with error check; detector self-diagnostics and

supervision programs,Rate-of-Rise Detection: 15°F / min. (8.3°C / min.) - Fixed: 135°F (57°C) ,

9 MR Field programmable as rate-of-rise or fixed temperature, Polarity insensitive, Superior EMI and No 12 9192.00 110304.00

RFI immunity, RoHS compliant. Detector shall have in-built isolator for better reliability,

circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator

feature in detector shall consider Isolator base in place of standard base OR separate

Isolator before and after every detector to comply the same without any extra cost.

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Manual

Pull Station Single Action, Shock and Vibration Resistant, with built in dual isolator, polarity

insensitive, Tri color LED for status (Green for Normal,Yellow for Faulty and RED for

activation), T-45 Key Reset lockset for easy maintenance, Operating Temp and RH: 0-49degC

11 MR and <=95%. MCP shall have in-built isolator for better reliability, circuit integrity and advanced No 8 4301.00 34408.00

fault finding. Manufacturers not having in-built Isolator feature shall provide separate

Isolator before and after every MCP to comply the same without any extra cost.

Supplying, installation, testing & commissioning of 8 zone, voice alarm controller with USB,

MP3 player (including 8 zone button paging station) with seamless integration facility with main

12 MR fire alarm panel for voice evacuation. 3. The controller shall comply standards of BS EN54-32 No 1 229838.00 229838.00

& EN608409, Controller shall have AC 230V and DC24V battery input. Auto switch into the

battery backup when AC fails.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms

operating at 240 Volt AC Supply complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm FS armoured cable, 600/1000V rated with

15 MR annealed copper conductor having XLPE insulation, steel wire armouring & FS outer sheath Mtr. 1490 235.00 350150.00

complete as required

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the

existing surface / recessed steel conduit of following pairs, cores and size including

connections and interconnections etc. as required.

Supplying and Laying of 2x1.5sqmm FS unarmourd cable Mtr 510 158.00 80580.00

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and

accessories like coupler etc. as required.

Supplying & Fixing of battery operated illiminated "EXIT" signage, with 2hrs power Battery

backup complete as required.

Supplying, Installing, Testing & Commissioning of LED technology, High efficiency,

Emergency light s with Function Use as an emergency luminaire Testing system Stand Alone,

Housing Polycarbonate, Glow wire test : 850°C, RAL9003, Type of mounting Surface:

Recessed base for ceiling, double sided cone diffuser, plexi plate diffuser, Degree of

19 MR protection IP65, Operation Mode Non Maintained or Maintained & Non Maintained mode NOS 2 7637.00 15274.00

selectable, Connection voltage 230V -/+ 5% [220V-240V] 50-60Hz, Permissible ambient:

temperature +5°C to +40°C, Battery: Ni-Cd, Duration 3 hours, Viewing distance 20m or 30m,

Insulation class II, 20 mtrs. viewing distance, Dimensions in mm: 270x119x49; for 30m viewing

distance version: 371x170x62

SITC of Remote Paging Microphone should be fully digital connected via CAT6 Cable with

Controller. The Microphone should have capability to make announcement in 96 Zones and

have all call facility. The Microphone shall have ability to control music and should be able to

route the music in zones. Microphone should have maximum zones capacity up to 120 Zones.

20 MR The Microphone should have LED indication for the different faults, the unit shall be able to NOS 1 158571.00 158571.00

indicate AC, DC, Fault, Mic and Test status through LED.. The Unit shall have 2 RJ45 ports for

Microphone so that the other microphone shall be able to link with the unit. The Microphone

shall have ability to Communication limit up to 600 Meters

Supply, Installation, Testing and Commisioning of Loop Card capacity of 159 detectors For

BMS Fire integration compatible with existing system

Supply, Installation, Testing and Commisioning of Interface Card for BMS fire integration

compatible with exisiting system

Supply, Installation, Testing and Commisioning of repeater panel having 160 character liquid

crystal with backlit control compatible with existing system

SITC of UL864 10th Edition UL Listed and FM approved Analog Addressable 2 Loop Fire

Alarm control panel. Panel shall be running on full digital protocol with 32 bit Microprocessor .

The Panel shall be complete with 6" color touch screen LCD Display. Fire alarm panel should

have minimum capacity of 2500 detectors and devices in any combination and capable of

making upto 50 loops in single panel using additional Loop cards. Each addressable loop

shall be capable of taking 250 addresses per loop configuring either as all detectors or

modules or any mix of both. The panel shall have the Fire Fighter Touch Screen Graphical

Display panel to inform & guide Fire Fighters for carrying out Fire Fighting operations. The

display shall have Hazmat icons indicating the presence of any explosive gas, liquids,

24 MR poison,fumes etc. If this feature is not available in fire alarm panel then additional fire fighter Nos 1 466667.00 466667.00

touch panel along with necessary hardware and software should be provided by the

manufacturers for fire fighters to guide them during emergency without any extra cost. To

expedite system troubleshooting, the system cards shall have ground fault detection and

diagnostic LEDs by card. In the display,simple building floor plan can be loaded in bitmap or

jpeg format, On the map, the user will see an icon indicating the location of the event in the

building in addition to a 'You-Are-Here' symbol to tell the responding person exactly where they

are in the building in relation to the event. The system shall be polarity insensitive. The panel

shall support degrade mode operation and shall have battery backup of 24 hrs in normal

condition and 30 minutes in Alarm condition.

TOTAL FIRE ALARM WORKS 841252.00 2285366.00

Digitally signed by SAKET

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S No DSR 2022/ DESCRIPTION QTY UNIT RATE TOTAL TOTAL AMOUNT

S No DSR 2022/ DESCRIPTION QTY UNIT RATE TOTAL TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Providing, laying, testing & commissioning of 'C' class

heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges,

18.7 tapers, nuts bolts, gaskets etc. and fixing the pipe on the

1 wall/ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel

paint of required shade complete as required :

Providing, fixing, testing & commissioning of 15mm dia

18.21 quartzoid bulb type sprinklers of rating 68 degree

2 centigrade with required accessories :

18.21.1 Pendant type 412 Each 522.00 215064.00

Supplying, installation, testing & commissioning of

sprinkler flexible pipe (UL Listed) of stainless steel

complete with 15 NPT on reducer thread with maximum

working pressure of 175 PSI test pressure of 875 PSI

3 18.25 (Burst) with branch line (Inlet) 25mm NPT male thread to

sprinkler head (Outlet) 15mm NPT female thread with

reducer, nipple, 2 side brackets, center bracket,

stockbar of following sizes complete as required.

Providing and fixing ISI Marked of approved make Fire

4 Extinguishers complete with all accessories as per

manufacturer's specifications.

a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). 4 NOS 12912.00 51648.00

Mechanical Foam gas cartridge type. 9 Kg capacity

ABC dry powder stored pressure type 6 kg capacity

Digitally signed by SAKET

SCHEDULE OF QUANTITIES: IPPBX

S NO DESCRIPTION UNIT QUANTITY RATE

Supply, Installation, Testing & Commissioning of Server based Communication

System with Duplicated Servers - working in Active Redundant Mode with Lic, all

the required licenses and Hardware - IP-PBX/IP Telephony Server: The IP

Telephony Solution shall support the following Services - Voice, Video, IM,

Presence and Audio Conference The Solution should be built on IP Server

archoitecture The IP Telephony Solution should support H.323 and SIP The

Solution should support the following Trunks - FXO, E1 PRI and SIP, equipped

1 with 2 PRI's from Day 1. The IP Telephony solution should incorporate all Nos 1 1494000.00 1494000.00

licenses for the Phones and Trunks Solution should support 100 IP Extensions

and 300 Analog Extension from Day 1 with future scalabilityupto 500 users.

Licenses for all Phones supplied should be provisioned on Day1 Solution should

support Hard 100 IP Phones, 500 Analog Phones Softphones, Video Phones,

Rack mount architecture, complete as required and as per technical

specifications.

Supply, Installation,Testing and commisioning of Executive Level IP Phone with

Color display – 3.7 inches x 2.1 inches (9.5 cm x 5.4 cm)- Diagonal width: 4.3

inches (11 cm), Touch Screen display, 4-position adjustable tilt display,

Permanently-labeled feature buttons:, speaker, mute, headset, contacts, home,

history, message, phone, forwarding, volume (separate volume levels in handset,

speaker, ringer, and headset), Red LEDs on speaker, mute, headset, message

and history, Wideband speakerphone 0-5 Softkeys, Ergonomic hearing aid

compatible, handset supporting TTD acoustic coupler, Bluetooth and DECT

2 headset support with adapter, Message waiting indicator, Ethernet Nos 7 27545.00 192815.00

(10/100/1000) line interface, Secondary Ethernet (10/100/1000)line interface,

Optional IEEE PoE 802.3af adapter registers as class 2 device, SIP protocol,

H.323 protocol support, Standards-based codec support: G.711, G.726,

G.729A/B, G722 , Supports the following languages: Arabic, Brazilian

Portuguese, Simplified, Chinese, Dutch, English, Canadian,French, Parisian

French, German,Hebrew, Italian, Japanese (Kanji,Hiragana and Katakana),

Korean, Latin American Spanish, Castilian Spanish, and Russian. Includ Licence.

Supply, Installation,Testing and commisioning of Type 2 IP Phone with Color

display 4-position adjustable tilt display, Permanently-labeled feature buttons:,

speaker, mute, headset, contacts, home, history, message, phone, forwarding,

volume (separate volume levels in handset, speaker, ringer, and headset), Red

LEDs on speaker, mute, headset, message and history, Wideband speakerphone

3 0-5 Softkeys, Ergonomic hearing aid compatible, handset supporting TTD Nos 14 17296.00 242144.00

acoustic coupler, Bluetooth and DECT headset support with adapter, Message

waiting indicator, Ethernet (10/100/1000) line interface, Secondary Ethernet

(10/100/1000)line interface, Optional IEEE PoE 802.3af adapter registers as

class 2 device, SIP protocol, H.323 protocol support, Standards-based codec

support: G.711, G.726, G.729A/B, G722 ,

Supply, Installation,Testing and commisioning of Type 3 Entry Level IP Phone

with display 4-position adjustable tilt display, Permanently-labeled feature

buttons:, speaker, mute, headset, contacts, Wideband speakerphone 0-5

Softkeys, Ergonomic hearing aid compatible, handset supporting TTD acoustic

4 coupler, Bluetooth and DECT headset support with adapter, Message waiting Nos 14 10249.00 143486.00

indicator, Ethernet (10/100/1000) line interface, Secondary Ethernet

(10/100/1000)line interface, Optional IEEE PoE 802.3af adapter registers as

class 2 device, SIP protocol, H.323 protocol support, Standards-based codec

support: G.711, G.726, G.729A/B, G722 ,

5 SITC of IP basaed operator console with DSS- 48/60 keys Nos 1 61497.00 61497.00

Supply Installation, Testing and Commissioning of Analog Speaker Phone with

23 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: ACCESS CONTROL

S TOTAL TOTAL

DSR DESCRIPTION UNIT QUANTITY RATE

NO AMOUNT AMOUNT

DSR (INR) NON-DSR (INR)

Supply, Installation, Testing and Commisioning of Biometric Face

smart card reader, Supports multiple smart card technologies -

iCLASS Seos, iCLASS SE/SR, MIFARE DESFire EV 1 and

MIFARE Yes Classic Standard iCLASS Access Control

Application IS014443A (MIFARE, DESFire, NFC) CSN, ISO

1 MR 14443B CSN, IS015693 CSN, Certifications-UL294, FCC; CE, Nos 10 22,523.00 2,25,230.00

ROHS, Supports on-board Wiegand interfaces, Supports

operating environment 0 to 60°C, Card reader should be

compatible with the sector layout of ECIL issued Yes cards

(mifare cards). The proposed reader OEM should ready for

customization if any with the final card design.

Supply Installation Testing & Commissioning of Access Control

Software Multi Reader and controller configuration and

upgradable to Enterprise level with unlimited users. Database

Supports: MS SQL, Oracle, and MS Access database types. Type

of technology supports: IRIS Scanner, Biometric, Face, RFID, etc

2 MR supports template management, Highly secured communication Nos 1 2,78,571.00 2,78,571.00

with the server, Allows for real-time monitoring of system status

and user activities with optional audio alerts. tamper detection,

network communication loss, and many other system attributes,

with the required attendance features. All required licesenses to

be supplied along with the solution

SITC of Access IP Master Controller cum Biometric Face Reader

with Enclosure & Power Supply- 1 door Universal 2 Reader

TCP/IP Controller Expandable upto 4 Reader with exit reader

module,Access Controller having a minimum 4 nos Encrypted

OSDP RS485 Wiegand supported Reader ports with on- board

option- a. 8 Inputs & 4 outputs & for b. 24 Inputs & 16 outputs,

3 MR Inbuilt RTC battery backup; supports power supply options of 12 Nos 5 53,965.00 2,69,825.00

VDC ± 10%, 500 mA /24 VDC or PoE/ PoE+. The Controller shall

have the capability to power up 600 mA maximum for 12V readers

& 300 mA for 5V readers through primary power current

supply.Temperature: 0 to 70°C (35 -150°F); Humidity: 20 to 80%

RH (non-condensing) , 10000 USERS & 10000 transactions,2

Supply, Installation, Testing & Commissioning of 12V, 5 Amp.

SMPS with MS Box Certified.

Supply and commissioing of MIFARE; DESFIRE; I Class card

formats. Supports 16 card formats per active reader, 8 per offline

reader; entire card number reported on invalid read; 19 digit

5 MR (32/64-bit) User 10 and 15 digit PIN numbers maximum; PIV, Nos 400 275.00 1,10,000.00

CAC, TWIC card compatible; 255 Access Levels per cardholder;

Supply Installation Testing and Commissioning of double leaf 600

6 MR LBS Door Electro Magnetic Lock with complete compatiable Nos 3 7,650.00 22,950.00

Bracket UL Listed.

Supply Installation Testing and Commissioning of Single leaf 600

7 MR LBS Door Electro Magnetic Lock with complete compatiable Nos 7 4,775.00 33,425.00

Bracket UL Listed.

Supply Installation Testing and Commissioning Touchless

Request to Exit button with detection range from 4 to 12 cm.

Supply Installation Testing and Commissioning Fire Exit panic Bar

9 MR single/double Door with EM lock and required accessories all Nos 10 14,624.00 1,46,240.00

Supply Installation Testing and Commissioning Emergency Door

10 MR Release Button, Gree, Key Resettable, Double Pole Double Nos 10 659.00 6,590.00

Supply Installation Testing and Commissioning of Cat 6 Network

Supply Installation Testing and Commissioning of 8 Core -

conductor20 to 22 AWG.

Supply Installation Testing and Commissioning of AC 3 Core

Plain Copper conductor, PVC insulated.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including cutting

14 MR the wall and making good the same in case of recessed conduit

24 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: A V SYSTEM

S No Item Description Unit Qty Rate Amount

1 SITC of active LED display wall area- 9.476 x 5.342ft, Pixel Pitch-1.5mm or lower, display area- 84.31 squre feet or more, SMD 3 in 1 technology, Nos 1 ₹ 44,84,148.00 ₹ 44,84,148.00

(1Red,1 Green,1Blue), Resolution 3840 x 2160 or higher, Brightness (Typical) 700 nit or higher, Bit Depth- 16 Bit(Internel processing-18 bit, Contarst

ratio- 8000:1 or higher, Viewing Angle Horizontal 150 degree or more, Viewing Angle Vertical- 150 degree or more, Frame Rate-60 Hz or above,

Refresh rate- 3840 HZ or higher, LED Lifespan- 100000 Hours, Duty Cycle- 24x7, etc all complete. Support structure included in the item

2 SITC of 65" latest Android 10 or higher panel with 3840 X 2160 resolution or better,, Wifi: 802.11 b/g/n ,Brightness: 440 Nits or higher, Contrast Ratio: Nos 5 ₹ 85,839.00 ₹ 4,29,195.00

1200:1, Aspect Ratio -16:9, Response Time (ms) -8 ms or lower, 24x7 operation, Viewing Angle-178°/178°, Inputs:HDMI 2.0 (x3) or more, USB 2.0

(x2), Multimedia support: 3GP, MKV, MP4, VOB,BMP, GIF, JPEG, JPG, PNG,AAC, M4A, MP3, IO Ports: USB2.0, Inbuilt speakers-2 x 10 W, 24/7

operation,HDR10,, 16GB GB onboard storage, Compliance: CE, RoHS, BIS, Complete in all respect and to be approved by consultant and his

representative. The system should have inbuilt Airplay & Chrome casting capability

3 SITC of Wall Mount push-pull type, capable of holding up to 45 kg and supports upto 65" displays, VESA Compliant etc all complete Nos 20 ₹ 10,121.00 ₹ 2,02,420.00

4 SITC of Multimedia Lectern with: Main body with 1.2-1.5m m steel plate; desk top with wood. Quality of wood should be meet the interior of the room. Nos 2 ₹ 2,94,673.00 ₹ 5,89,346.00

Solid wood handrail.Rack: Built-in standard rack with dimension 18U, front glass, 90mm cooling fan along with separate drawer for storage, keyboard

drawer and mouse, with keys Screen/Panel :Annotation Display 22" with pen touch, aspect ration 16:9, PC: Intel-i7-7th Gen.,16 GB RAM, 512 GB

SSD, Windows 11 Pro or latest, Open Size: 1150 x 650 x 1000 mm ( LxWxH), Design 1:Podium body corner circular arc is used to design, to prevent

bruising. Interface: Equipped with laptop interface/port (1xHDMI, 2x USB//2x Power point/1x RJ45/ 1x mini XLR for microphone, Design 2: The Podium

is designed according to the standard cabinet size as mentioned above, all the equipment are neatly Special designed and positioned. Tray:Separate

foldable Tray for document camera (566x385x152 mm) folded condition Features: Ease of access and minimum latch sound in open/close.

5 SITC of Cable Cubby with flip top, cover, Wireless Charging capability and 2 Universal Power Socket , 1xRJ45, 1xHDMI, 1 USB-A, & 1xUSB-C made of Nos 6 ₹ 55,975.00 ₹ 3,35,850.00

aluminium etc all complete

6 SITC of Cable Cubby with flip top, cover, 2 Universal Power Socket , 1xRJ45, 1xHDMI, 1 USB-A, & 1xUSB-C made of aluminium etc all complete Nos 24 ₹ 12,812.00 ₹ 3,07,488.00

7 SITC of Wireless Presentation Platform,4K UHD (3840*2160) @ 30Hz. HDMI 1.4b or USB-C DisplayPort 1.2 (only Gen2) Audio output, USB, HDMI, Nos 2 ₹ 1,98,170.00 ₹ 3,96,340.00

USB, 1 X USB-A, 1 X USB-C, dongle Buttons x2, App , Desktop & Mobile Native protocols, Airplay, Google Cast, Miracast, Maximum number of

simultaneous connections (with Buttons and/or App), 32, Authentication protocol WPA2-PSK in stand alone mode WPA2-PSK or IEEE 802.1X

8 SITC of PTZ Camera with AI-Powered Human Detection 3 Tracking modes and 2 Framing modes, Mount upright or inverted, HDMI, Ethernet, 3G-SDI Nos 2 ₹ 3,33,259.00 ₹ 6,66,518.00

and USB simultaneous output, 1080p 60fps with 20x Optical Zoom. Supply, Installation Testing & Commissioning of minimum PTZ Camera with AI-

Powered Human Detection , Optical Zoom : 20X or better, Digital Zoom : 20X, Resolution : 2160p30 or better, Video S/N: ≥54dB, Supports PoE or

better, Compatible with applications such as WebEx, Microsoft Teams, Zoom, GoToMeeting or any link based application & should have UVC: 1.1

compliant, Pan range: +/- 170 degrees, Tilt range: -35 degrees to +90 degrees, Number of Presets: 150 or more, Video Interface : 1 x HDMI, Camera

control : Visca over IP / 1 x LAN Port, Ceiling / wall mount : Included, Minimal Illumination: 0.5 lux or better, Video Output on HDMI, IP, USB or more, IP

streaming: H.265 or better, Audio interface: 1 X line In, 1X Mic In, 1 X line out, USB: 1X USB 3.0 and 1X USB 2.0, Support Protocols: TCP/IP, HTTP,

RTSP, RTMP, Onvif, DHCP, Multicast, or more, etc complete as per technical specification.

9 SITC of IP based dual stream encoder with PoE via a 10/100/1000 MBps Ethernet network. HDMI local output, 2xHDMI IN, Analog audio input. 4K 60 Nos 15 ₹ 1,45,769.00 ₹ 21,86,535.00

MWC 4:4:4 encoding supported. Video preview thru web interface, Virtual USB 2.0 Hub, Advanced EDID Management. USB 2.0 Devices / mass

storage data support, HDCP2.2 compliant, RS-232 and IR IN & Out support, power thru POE or Optional External Adapter etc as required.

10 SITC of IP based Decoder with PoE via a 10/100/1000 MBps Ethernet network. HDMI output, Analog audio Output, 4K 60 MWC 4:4:4 encoding Nos 14 ₹ 1,45,769.00 ₹ 20,40,766.00

supported. Video preview thru web interface, Virtual USB 2.0 Hub, Advanced EDID Management. USB 2.0 Devices / mass storage data support,

HDCP2.2 compliant, RS-232 and IR IN & Out support, power thru POE or Optional External Adapter etc as required.

11 SITC of USB 2.0 over LAN device side extender with 4 USB 2.0 ports and an Ethernet interface for sending USB data. Maximum 100 meter direct Nos 4 ₹ 1,25,362.00 ₹ 5,01,448.00

CAT6/7 cable connectivity to switches or USB 2.0 host side extenders. Dynamic pairing between device and host side extenders using control buttons or

a UDP protocol. Interoperability with other products implementing the ExtremeUSB(R) technology for USB 2.0 extension. Device class filtering.

Transparent USB extension. True Plug and Play. Throughput up to 480Mbps. Several mounting possibilities including racks, under desk kit, etc. Small

form factor anf light weight.

12 SITC of USB 2.0 over LAN host side extender with an Ethernet interface for receiving USB data from up to 7 device side extenders. Maximum 100 meter Nos 12 ₹ 1,25,362.00 ₹ 15,04,344.00

direct CAT6/7 cable connectivity to switches or USB 2.0 device side extenders. Dynamic pairing between device and host side extenders using control

buttons or a UDP protocol. Interoperability with other products implementing the ExtremeUSB(R) technology for USB 2.0 extension. Device class

filtering. Transparent USB extension. True Plug and Play. Throughput up to 480Mbps. Several mounting possibilities including racks, under desk kit, etc.

Small form factor anf light weight.

13 SITC of table embedded microphone, Type: Electret Condenser, Frequency Response: 40 to 17,000Hz, Polar Pattern: Omnidirectional, Sensitivity (at Nos. 28 ₹ 51,247.00 ₹ 14,34,916.00

1,000Hz): -48 ± 3dB, Attenuation Switch: -10dB, Low-Frequency Roll-off: 80Hz, Impedance: 220Ω, Max. SPL For 1% T.H.D: 140dB, Signal-To-Noise

Ratio: 68dB, Current Consumption: ≤ 3mA, Power Supply: 9 - 52 VDC phantom power, reject radio frequency interference, etc. complete required as

per specifications.

14 SITC of table-embedded button with lighting indication, should integrate with table-embedded microphone which can communicate with microphone, Nos. 32 ₹ 11,531.00 ₹ 3,68,992.00

etc. complete required as per specifications.

15 SITC of ceiling microphone tile with built-in 30nos. or more MEMS technology, beamforming technology, coverage pattern: customizable, Beamforming Nos. 4 ₹ 5,44,504.00 ₹ 21,78,016.00

Range: 100 Hz to 20 kHz, Beam Pointing Accuracy: 0.2 dB or better, Dynamic Range: 20 Hz to 20 kHz, Number of Beams: Up to 10 or more, built-in

Acoustic Echo Cancellation, Noise Cancellation, Automatic Level Control, Gain Adjust, Mute On/Off, built-in/external amplifier channel: 4 or more,

wattage: 15watt or more per channel, built-in Dante/P-Link for communication protocol, PoE built-in, built-in camera tracking functionality, with required

PoE from the same OEM, complete required as per specifications.

17 Supply, installation, testing and commissioning of digital signal processor with P-Link / Dante: 16X16, input: 12 or more with AEC, output: 8 or more, C Nos 5 ₹ 5,12,474.00 ₹ 25,62,370.00

Link: 150 or more channel bus, USB audio should be built in for software based video conference, GPIO port for Chairman priority, RS-232 and

Ethernet over IP, camera tracking, built in third party control module, can be controllable and monitorable through PC/Phone and for any central control

room, built in noise cancellation, Dynamic Range: 20 Hz – 20 kHz @ 0 dB, Crosstalk (Mic/Line): Channel to Channel, stimulus at 20 dBu to receptor at -

56 dBu, 1 kHz, < -98 dB, Maximum Input Level: -65 dBu to 20 dBu, Frequency Response: 20 Hz – 22 kHz, front panel should have lighting indications,

Sensor Type: Capacitive Touch Button, etc complete requried as per specifications.

18 SITC of 6" Compact Full Range Ceiling Speaker, Driver Size : 1 x 6.5” LF Driver , RMS Power : 50 W , Nominal impedance: 8 Ohm, Transformer Taps : Nos 24 ₹ 26,608.00 ₹ 6,38,592.00

100V / 70V upto 30W, Frequency Range : 75 Hz-20 kHz Maximum SPL : Peak - 113dB, Dispersion: 110 Degree Conical , Sensitivity: 90dB,

Certification: EN54-24, UL 1480, UL 2043, Aluminum, powder coated grill, Complete with Accessories

19 SITC of 4-channel 1000Watt power amplifier Class D, Nos. of Channel : 4, THD 20Hz-20kHz at 1 W <0.1%, Signal To Noise Ratio >106 dB , Channel Nos 2 ₹ 2,43,425.00 ₹ 4,86,850.00

separation at 1 kHz >70 dB, Power Handling : 4 × 250 W @ 2 Ohms / 4Ohms / 8 ohms / 16 ohms, Power Handling : 4 x 250W @ 70V, Pea k output

voltage per channel 100 V / 70 Vrms, Frequency Response : 20 Hz - 20 kHz, Input impedance 20 kOhm, Common Mode Rejection (CMR) 50 dB,

Enerygy Star Rated, Comprehensive circuit protection and fault indication

20 SITC of control processor with rack-mountable quad-core processor Network connections: RJ45 10/100/1000 Gbps Ethernet Port, 4 x Relays Nos 2 ₹ 1,86,585.00 ₹ 3,73,170.00

configurable to NO, NC, or COM, 4 x IR emitter ports with variable output level, 3 x RS-232 serial ports (TX, RX, GND), 4xDigital IO ports, Power &

Ethernet Indicator LEDs, Primary processor for IP, IR, RS-232, Sensor, Relay and 12-Volt control, Provides instant two-way control of Total Control and

compatible third-party devices, Ultra fast processor of 1600 MIPS, 512MB Onboard RAM, 8GB Flash Memory, etc including any expander as required at

22 SITC of Apple iPad Air 11″ Multi-Touch display with User Control Interface (UCI) Deployment etc all complete with Sleeves & induction based, wall Nos 2 ₹ 1,21,951.00 ₹ 2,43,902.00

mounted docking station

23 SITC of Wireless Access Point etc all complete Nos 3 ₹ 15,549.00 ₹ 46,647.00

24 SITC of 2m/6.5ft HDMI 2.0 Cable, 18Gbps 4K60Hz, Dolby Vision & HDR, ARC,CEC, ALLM, VRR, | CL3 & VW-1 Rated etc all complete Nos 61 ₹ 1,555.00 ₹ 94,855.00

25 USB 3.0 -1.8 meter with Gold Plated and Outer Molding PVC- Black -Male to Male - Type A Nos 27 ₹ 1,866.00 ₹ 50,382.00

26 SITC of USB-C Cables 2 mtr Nos 16 ₹ 1,399.00 ₹ 22,384.00

27 SITC of 2 Conductor 16 AWG Speaker Cable, stranded Bare copper conductors, PVC/Nylon insulation, PVC jacket (as per actual) etc all complete Metre 150 ₹ 233.00 ₹ 34,950.00

28 SITC of Category 6A Cable, 4 Pair, S/FTP, PVC jacket (as per actual) etc all complete Rolls 5 ₹ 25,000.00 ₹ 1,25,000.00

29 SITC of Various Cables & Connectors etc all complete Lot 3 ₹ 31,098.00 ₹ 93,294.00

30 SITC of 32U, Equipment Rack, with Front & Side doors, 4 No Fan Assembly, on Top of the Rack, 4 Caster wheels, 2 no Shelfs to mount the Nos 1 ₹ 75,000.00 ₹ 75,000.00

equipments which are not rack mounted, 8X2, 5/6 Amp. Power Distribution Unit, Cable Manager & Sufficient Rack hardwares etc all complete

32 SITC of Wall Mount, capable of holding up to 100 kg and supports 98" displays, VESA Compliant etc all complete Nos 1 ₹ 27,000.00 ₹ 27,000.00

33 SITC of 2 Conductor 16 AWG Speaker Cable, stranded Bare copper conductors, PVC/Nylon insulation, PVC jacket (as per actual) etc all complete Metre 225 ₹ 233.00 ₹ 52,425.00

34 SITC of 85" Intractive Display with OPS display with Resolution 3,840 x 2,160, Brightness (Typical) 350, Contrast Ratio 4,000 : 1, HDMI In 2, DP In Nos 1 ₹ 3,20,122.00 ₹ 3,20,122.00

Yes, USB 2, IR In Yes, RS232 In Yes, latest Android operating system, boosts the displays overall performance, extensive connectivity and ongoing 24/7

performance etc., Compliance: CE, RoHS, BIS, BEE or EnergyStar. The system should have inbuilt casting capability

35 SITC of Wall Mount, capable of holding upto 86" displays, VESA Compliant etc all complete Nos 2 ₹ 12,439.00 ₹ 24,878.00

36 SITC of Mini PC with 13th Gen Intel® Core™ i7-13700 (30 MB cache, 16 cores, 24 threads, 2.10 GHz to 5.10 GHz Turbo, 65 W), laptop Windows 11 Nos 2 ₹ 1,22,000.00 ₹ 2,44,000.00

Pro, memory 16 GB: 1 x 16 GB, DDR5, harddriveM.2 2230 512GB PCIe NVMe SSD Class 25 Dimension : Width: 36 mm (1.43 in.), Depth: 178 mm

(7.01 in.), Height: 182 mm (7.17 in.)

37 SITC of Wireless Presentation Platform,4K UHD (3840*2160) @ 30Hz. HDMI 1.4b or USB-C DisplayPort, Audio output, USB, HDMI, USB, 1 X USB-A, Nos 1 ₹ 1,29,573.00 ₹ 1,29,573.00

1 X USB-C, dongle Buttons x2, App , Desktop & Mobile Native protocols, Airplay, Google Cast, Miracast, Maximum number of simultaneous

connections (with Buttons and/or App), 32, Authentication protocol WPA2-PSK in stand alone mode WPA2-PSK or IEEE 802.1X

38 Supply, Installation, testing and commissioning of switcher which consist USB-B Connector, Audio: Digital audio, 2 x 2 bidirectional channels, Sample Nos 2 ₹ 96,089.00 ₹ 1,92,178.00

Rate: 48 kHz, Sample Bit Depth: 24 Bit, Compatible: USB 2.0, USB 3.0, USB Cable Distance: 16 feet, Compatible: Windows & Mac OS devices, 1 x

USB 3.0 (Type-B) for laptop, 2 x USB 3.0 (Type-A), 4 x USB 2.0 ports, 1 x HDMI out, 1 x DVI out, etc complete required as per specifications

39 Supply, Installation, testing and commissioning of Ceiling microphone tile beamforming technology, coverage pattern: customize, Beamforming Range: Nos 2 ₹ 5,95,751.00 ₹ 11,91,502.00

100 Hz to 20 kHz, Beam Pointing Accuracy: 0.2 dB or better, Dynamic Range: 20 Hz to 20 kHz, Number of Beams: Up to 10 or more, built in Acoustic

Echo Cancellation, Noise Cancellation, Automatic Level Control, Gain Adjust, Mute On/Off, built-in / external amplifier channel: 4 or more, wattage:

15watt or more per channel, built in Dante/P-Link for communication protocol, PoE built in, built in camera tracking funtionality, with requried PoE from

the same OEM with Dante/P-Link converter, Supports 2x2 channels of bidirectional audio, Automatically discover and natively configure, PoE, etcetc

complete required as per specifications.

Digitally signed by SAKET

40 Supply, Installation Testing & Commissioning of Camera with minimum Optical Zoom : 12X or better, Digital Zoom : 20X, Resolution : 2160p30 or Nos 7 ₹ 2,20,364.00 ₹ 15,42,548.00

better, Video S/N: ≥54dB, Supports PoE or better, Compatible with applications such as WebEx, Microsoft Teams, Zoom, GoToMeeting or any link

based application & should have UVC: 1.1 compliant, Pan range: +/- 170 degrees, Tilt range: -35 degrees to +90 degrees, Number of Presets: 150 or

more, Video Interface : 1 x HDMI, Camera control : Visca over IP / 1 x LAN Port, Ceiling / wall mount : Included, Minimal Illumination: 0.5 lux or better,

Video Output on HDMI, IP, USB or more, IP streaming: H.265 or better, Audio interface: 1 X line In, 1X Mic In, 1 X line out, USB: 1X USB 3.0 and 1X

USB 2.0, Support Protocols: TCP/IP, HTTP, RTSP, RTMP, Onvif, DHCP, Multicast, or more, etc complete as per technical specification.

41 SITC of Mic Pod Extension Cable- 10 m. Nos 2 ₹ 27,439.00 ₹ 54,878.00

42 SITC of 10 Meter Premium High Speed HDMI 2.0b Flexy Cable, Bandwidth up to 18Gbps, Up to 4096x2160@60Hz at RGB 4:4:4 video resolution, High Nos 2 ₹ 3,887.00 ₹ 7,774.00

Dynamic Range (HDR10), Dolby Vision and Hybrid log–gamma (HLG) video etc all complete

43 SITC of USB Type A to Type B Cable 10 Mtr AOC Nos 4 ₹ 11,663.00 ₹ 46,652.00

44 SITC of Various Cables & Connectors etc all complete Lot 2 ₹ 15,549.00 ₹ 31,098.00

45 SITC of 75" latest Android 10 or higher panel with 3840 X 2160 resolution or better,, Wifi: 802.11 b/g/n ,Brightness: 440 Nits or higher, Contrast Ratio: Nos 2 ₹ 1,92,178.00 ₹ 3,84,356.00

1200:1, Aspect Ratio -16:9, Response Time (ms) -8 ms or lower, 24x7 operation, Viewing Angle-178°/178°, Inputs:HDMI 2.0 (x3) or more, USB 2.0

(x2), Multimedia support: 3GP, MKV, MP4, VOB,BMP, GIF, JPEG, JPG, PNG,AAC, M4A, MP3, IO Ports: USB2.0, Inbuilt speakers-2 x 10 W, 24/7

operation,HDR10, 16GB onboard storage, Compliance: CE, RoHS, BIS, Complete in all respect and to be approved by consultant and his

representative. The system should have inbuilt Airplay & Chrome casting capability

46 SITC of 55" latest Android 10 or higher panel with 3840 X 2160 resolution or better,, Wifi: 802.11 b/g/n ,Brightness: 440 Nits or higher, Contrast Ratio: Nos 9 ₹ 68,597.00 ₹ 6,17,373.00

1200:1, Aspect Ratio -16:9, Response Time (ms) -8 ms or lower, 24x7 operation, Viewing Angle-178°/178°, Inputs:HDMI 2.0 (x3) or more, USB 2.0

(x2), Multimedia support: 3GP, MKV, MP4, VOB,BMP, GIF, JPEG, JPG, PNG,AAC, M4A, MP3, IO Ports: USB2.0, Inbuilt speakers-2 x 10 W, 24/7

operation,HDR10, 16GB onboard storage, Compliance: CE, RoHS, BIS, Complete in all respect and to be approved by consultant and his

representative. The system should have inbuilt Airplay & Chrome casting capability

47 SITC of 10m HDMI 2.0 AOC | 24Gbps | 4K60Hz | Dolby Vision & HDR | ARC, CEC, ALLM & VRR | ISF Certified | FT4, CL4 etc all complete Nos 22 ₹ 4,664.00 ₹ 1,02,608.00

48 SITC of 43" latest Android 10 or higher panel with 3840 X 2160 resolution or better,, Wifi: 802.11 b/g/n ,Brightness: 440 Nits or higher, Contrast Ratio: Nos 9 ₹ 47,256.00 ₹ 4,25,304.00

1200:1, Aspect Ratio -16:9, Response Time (ms) -8 ms or lower, 24x7 operation, Viewing Angle-178°/178°, Inputs:HDMI 2.0 (x3) or more, USB 2.0

(x2), Multimedia support: 3GP, MKV, MP4, VOB,BMP, GIF, JPEG, JPG, PNG,AAC, M4A, MP3, IO Ports: USB2.0, Inbuilt speakers-2 x 10 W, 24/7

operation,HDR10,16GB onboard storage, Compliance: CE, RoHS, BIS, Complete in all respect and to be approved by consultant and his

representative. The system should have inbuilt Airplay & Chrome casting capability

49 SITC of Various Cables & Connectors etc all complete Lot 16 ₹ 7,774.00 ₹ 1,24,384.00

50 SITC of 2m/6.5ft HDMI 2.0 Cable, 18Gbps 4K60Hz, Dolby Vision & HDR, ARC,CEC, ALLM, VRR, | CL3 & VW-1 Rated etc all complete Nos 1 ₹ 1,244.00 ₹ 1,244.00

51 SITC Digital Signage Media player with client license Nos 1 ₹ 64,787.00 ₹ 64,787.00

52 SITC of 5m HDMI 2.0 18Gbps | 4K60Hz | Dolby Vision & HDR | ARC, CEC Nos 2 ₹ 4,664.00 ₹ 9,328.00

53 SITC of Fixed Dual Side Floor mount , capable of holding up to 125 kg and supports 65" displays, VESA Compliant etc all complete Nos 1 ₹ 18,659.00 ₹ 18,659.00

54 SITC of Full HD 1080p Document Camera output resolution with 30fps, Large (A3+) shooting area for documents and 3D objects, Full sized built-in Nos 1 ₹ 1,17,378.00 ₹ 1,17,378.00

LED backlight design for X-rays, film, and slides, VGA, HDMI input and output and supports VGA, HDMI pass-thru, 20x variable zoom ratio Dual

gooseneck anti-reflection lamps Folds down to a height of six inches

55 Supply, Installation, testing and commissioning of wireless microphone receiver with 8no. channel transmitter, channel: 330 or more,frequency range: Nos 1 ₹ 5,57,315.00 ₹ 5,57,315.00

UHF, switching bandwidth/tunning range: 150MHz or more, built in Dante & PoE both, security: AES-256 and FIPS both, ethernet connectivity, shall be

wall or ceiling mountable, certifications: BIS, FCC, IC and CE with charging docking station of 8 channel only etc complete required as per specifications

56 Supply, Installation, testing and commissioning of wireless boundary transmitter, frequency band: UHF, dual selectable polar pattern: omnidirectional & Nos 7 ₹ 99,932.00 ₹ 6,99,524.00

Cardioid, Battery: rechargable, USB charging option should be built in for emergency, multicolour lighting indications, battery perfor time: minimum 12hr

or better, built in audio Preamp with an adjustable gain of -20, -10, 0 to +31 dB for better audio quality, Low-Cut filter (75 Hz), etc complete required as

per specifications.

58 13 inches (33.02 cm) Pixel Sense Flow Display, Resolution: 2880 X 1920 (or higher), 120Hz Refresh Rate 16GB RAM, 256GB storage, Intel Core i7 Nos 5 ₹ 2,50,000.00 ₹ 12,50,000.00

12th Generation Processor (or higher), Windows 11 OS, Upto 15.5 Hours Battery Life (or higher), 10 MP Primary Camera, Stereo Speaker with Dolby

Atmos, Dolby Vision IQ Display Signature Keyboard, Mouse with Slim Pen 2 – Black from same manufacturer, WiFi 6E: 802.11ax compatible, Bluetooth

59 SITC of USB Cables 10 mtr Nos 2 ₹ 8,551.00 ₹ 17,102.00

60 SITC of 24U, Equipment Rack, with Front & Side doors, 4 No Fan Assembly, on Top of the Rack, 4 Caster wheels, 2 no Shelfs to mount the Nos 1 ₹ 32,030.00 ₹ 32,030.00

equipments which are not rack mounted, 8X2, 5/6 Amp. Power Distribution Unit, Cable Manager & Sufficient Rack hardwares etc all complete

TOTAL COST ₹ 3,10,08,518.00

Digitally signed by SAKET

QUOTATION FOR MODULAR FURNITURE

SL NO DESCRIPTION/ SPECIFICATIONS IMAGE/DRAWING QTY UNIT RATE AMOUNT

TABLE FOR CHAIRPERSON ROOM

SIZE - 2960W X 2000D X 750HT

1W X in office desk in warm walnut laminate and leather.

2. Side cabinet with inbuilt wire management box with data and power ports.

–Made using MDF and walnut finished laminate. The E1 grade medium density fiber board is a highly durable material and a world standard for premium furniture while the

laminate is from our carefully selected range of premium laminates with consistent color and grain structure.

–Desk is a minimally designed contemporary 10 feet office desk finished in Felix walnut laminate and leather. Suitable for large and modern office cabins it also includes a side

cabinet with wirebox having power & data ports. While the table is built with Eo grade MDF wood it is finished with a cutting edge laminate for natural wood like feel and luxurious

looks. It is part of the Desk series from which you can also choose an entire range of matching contemporary office furniture. The product range includes smaller office tables,

conference tables, bookshelves etc to create a complete office.

TABLE FOR MEMBERS / SECRETARY

MODEL:- 2600W X 2000D X 760HT

Desk, two pedestals with storage, modesty panel and wirebox for managing your data and power cables.

–Office desk in 8 feet width with storage pedestal made with environment grade engineered wood and walnut laminate. The E1 grade MDF is a highly durable material and a

world standard for premium office furniture while the walnut laminate is from our carefully selected range of premium laminates with consistent color and grain structure.

–This elegant, 8 feet width office table comes in rich walnut and solid gray laminate combination with golden metal edge banding. Its generous dimensions and dark wood finish

makes it a perfect choice for an elegant office cabin with contemporary interiors. Also included with the table are two storage pedestal, leather writing pad and inbuilt wire

2 management provision with a wirebox for a clutter free work area. Built with top grade MDF walnut laminate for lasting durability, natural feel and luxurious looks. 5 Nos ₹ 2,05,951.00 ₹ 10,29,755.00

TABLE FOR ADVISIORS

SIZE: MAIN TABLE - 2100W X 900D X 750HT

SIDE STORAGE: 1050W X 450D X 750HT

BACK STORAGE: 1800W X 450D X 750HT

MOBILE PEDESTAL: 400W X 450D X 640HT

MAIN TABLE:- The main table shall be made of 25mm thick PLB one side pre-laminate board confirming to IS-14587:1998. Soft closing access flap with in-built power box to

be provided on work surface for wire management. Return table Work Surface should be made of 25mm thick PLB one side pre-laminate board confirming to IS-14587:1998.

PLB will be E1-P2 grade and approved shade. Confirming to IS-12823:1990. 2 mm thick PVC edge band will confirm to DIN 68861 for resistance to clearers. The edge band

material should have Shore D hardness of 79± 4. The Hot melt glue used for fixing the PVC edge band should have ISO 9001- 2015 quality certification confirming to ASTM D

4499 standards for viscosity and thermal stability. The edges should be PVC Edge banded with matching finish or have an option of reverse water fall edges.Modesty Panel

shall be made of 18mm thick PLT both sides pre-laminate board confirming to IS-14587:1998.The height of modesty shall be 450 mm.The modesty panel will be connected to

the main table by 2 nos special Aluminum extruded brackets. The modesty will be fixed 150 mm from the edge of the table.

Wire Management:Continuous PVC Cable Tray with provision to mount switches and sockets as per client requirement. Vertical wire entry cover for wire uptake from floor to

cable tray and 300mm Aluminium Flip Up for swicth access.

Legs and Supports:- The MS supports are made of diamond shape ERW tubes- 16g with levelers to cater for floor undulations- +/- 20 mm. ERW Tube confirming to IS 4923 :

1997 – 16g. Main leg members will be connected through a horizontal member size 1.6mm thk, 25x25 cold formed ERW tube confirming to IS 4923: 1997. The vertical and the

horizontal tubes will be welded with CO2 MIG welding process confirming to IS 816 and ISO 9692-2. The leg will be fabricated using Argon & Co2 gas mixture on a Robotic

welding machine to ensure adequate welding strength with consistency.• The legs will be connected with Cross beams to take care of the bending stress catering up to 1800 mm

length and up to 900 mm depth of the work surface.

Finish:- All metal components & aluminum die cast parts will be powder coated by Nano ceramic surface treatment process compiled to a Bend test-ASTM D3451 – 06,

Adhesion -DIN EN 14901 Salt spray test- DIN EN ISO 9227, which is non-hazardous, environmental friendly and will have uniform powder coating thickness of 50-60-micron

MOBILE PEDESTAL:-400W X 450D X 600HT

The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick.

The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller

channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one

single key.Product should be BIFMA Compliance.

COMPOSITE SIDE HT ADJ STORAGE :-

The structure is made out of 18mm Thick Pre-Laminated Particle Board. The Shelves are adjustable in height. The shutters are fitted with auto closing hinges. Finger Grooves

Handles, central locking system , levellers & other necessary hardware are priovided.

BACK STORAGE- The storage will be made in 18 MM PLB (Pre laminated board) with the density of 680kg/m³ and 18 mm thick one side pre-laminate board confirming to IS

12406 : 2013. Surface: CPL ( continuous pressure laminate) in 0.5mm thickness in melamine finish. The PLB will be confirming to E-1 Grade as per the JIS A 5905-2003

standards and approved shade confirming to IS-12823:1990.The back of storage will be made in 9 MM PLB (Pre laminated board) with the density of 680kg/m³ and 18 mm thick

one side pre-laminate board confirming to IS 12406 : 2013. Surface: CPL ( continuous pressure laminate) in 0.5mm thickness in melamine finish. Storgage will be provided with

edge banding 2 mm thick PVC edge band will confirm to DIN 68861 for resistance to clearers. The Hot melt glue used for fixing the PVC edge band should have ISO 9001-

2015 quality certification and confirm to ASTM D 4499 standards for viscosity and thermal stability. The edge band material should have Shore D hardness of 79± 4. storage will

have two adjustable shelves making 3 compartments.The shutters are fitted with auto closing hinges.Central locking system , levellers & other necessary hardware are

priovided.Handles will be hand grooved.

Digitally signed by SAKET

FOR JOINT ADVISOR

SIZE: MAIN TABLE - 2100W X 900D X 750HT

SIDE STORAGE: 1050W X 450D X 750HT

BACK STORAGE: 1800W X 450D X 750HT

MOBILE PEDESTAL: 400W X 450D X 640HT

MAIN TABLE:- The main table shall be made of 25mm thick PLB one side pre-laminate board confirming to IS-14587:1998. Soft closing access flap with in-built power box to

be provided on work surface for wire management. Return table Work Surface should be made of 25mm thick PLB one side pre-laminate board confirming to IS-14587:1998.

PLB will be E1-P2 grade and approved shade. Confirming to IS-12823:1990. 2 mm thick PVC edge band will confirm to DIN 68861 for resistance to clearers. The edge band

material should have Shore D hardness of 79± 4. The Hot melt glue used for fixing the PVC edge band should have ISO 9001- 2015 quality certification confirming to ASTM D

4499 standards for viscosity and thermal stability. The edges should be PVC Edge banded with matching finish or have an option of reverse water fall edges.Modesty Panel

shall be made of 18mm thick PLT both sides pre-laminate board confirming to IS-14587:1998.The height of modesty shall be 450 mm.The modesty panel will be connected to

the main table by 2 nos special Aluminum extruded brackets. The modesty will be fixed 150 mm from the edge of the table.

Wire Management:Continuous PVC Cable Tray with provision to mount switches and sockets as per client requirement. Vertical wire entry cover for wire uptake from floor to

cable tray and 300mm Aluminium Flip Up for swicth access.

Legs and Supports:- The MS supports are made of diamond shape ERW tubes- 16g with levelers to cater for floor undulations- +/- 20 mm. ERW Tube confirming to IS 4923 :

1997 – 16g. Main leg members will be connected through a horizontal member size 1.6mm thk, 25x25 cold formed ERW tube confirming to IS 4923: 1997. The vertical and the

horizontal tubes will be welded with CO2 MIG welding process confirming to IS 816 and ISO 9692-2. The leg will be fabricated using Argon & Co2 gas mixture on a Robotic

welding machine to ensure adequate welding strength with consistency.• The legs will be connected with Cross beams to take care of the bending stress catering up to 1800 mm

length and up to 900 mm depth of the work surface.

Finish:- All metal components & aluminum die cast parts will be powder coated by Nano ceramic surface treatment process compiled to a Bend test-ASTM D3451 – 06,

Adhesion -DIN EN 14901 Salt spray test- DIN EN ISO 9227, which is non-hazardous, environmental friendly and will have uniform powder coating thickness of 50-60-micron

MOBILE PEDESTAL:-400W X 450D X 600HT

The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick.

The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller

channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one

single key.Product should be BIFMA Compliance.

COMPOSITE SIDE HT ADJ STORAGE :-

The structure is made out of 18mm Thick Pre-Laminated Particle Board. The Shelves are adjustable in height. The shutters are fitted with auto closing hinges. Finger Grooves

Handles, central locking system , levellers & other necessary hardware are priovided.

BACK STORAGE- The storage will be made in 18 MM PLB (Pre laminated board) with the density of 680kg/m³ and 18 mm thick one side pre-laminate board confirming to IS

12406 : 2013. Surface: CPL ( continuous pressure laminate) in 0.5mm thickness in melamine finish. The PLB will be confirming to E-1 Grade as per the JIS A 5905-2003

standards and approved shade confirming to IS-12823:1990.The back of storage will be made in 9 MM PLB (Pre laminated board) with the density of 680kg/m³ and 18 mm thick

one side pre-laminate board confirming to IS 12406 : 2013. Surface: CPL ( continuous pressure laminate) in 0.5mm thickness in melamine finish. Storgage will be provided with

edge banding 2 mm thick PVC edge band will confirm to DIN 68861 for resistance to clearers. The Hot melt glue used for fixing the PVC edge band should have ISO 9001-

2015 quality certification and confirm to ASTM D 4499 standards for viscosity and thermal stability. The edge band material should have Shore D hardness of 79± 4. storage will

have two adjustable shelves making 3 compartments.The shutters are fitted with auto closing hinges.Central locking system , levellers & other necessary hardware are

priovided.Handles will be hand grooved.

TABLE FOR DEPUTY ADVISIORS/ PA/ PS

SIZE- 1650W X 750D X 750HT

SIDE STORAGE - 900W X 450D X 750HT

BACK STORAGE - 1200W X 450D X 750HT

Table Top: 25mm thick Pre laminate particle board with 2mm PVC edge lipping on all exposed edges(Straight/Reverse waterfall edge)

End Legs : Powder coated Al die casted Enrich legs

Modesty Panel: 18mm thk pre lam board with 2mm PVC edge lipping of 450mm Ht.

Wire Management: 450mm Aluminium Flip Up and provision to mount swicthes and sockets on PVC cable dump and Vertical wire entry cover or vertebra for wire uptake from

floor to cable dump

COMPOSITE SIDE STORAGE:

5 The structure is made out of 18mm Thick Pre-Laminated Particle Board. The Shelves are adjustable in height. The shutters are fitted with auto closing hinges. Finger Grooves 38 Nos ₹ 58,056.00 ₹ 22,06,128.00

Handles, central locking system, levellers & other necessary hardware are priovided.

BACK STORAGE- The storage will be made in 18 MM PLB (Pre laminated board) with the density of 680kg/m³ and 18 mm thick one side pre-laminate board confirming to IS

12406 : 2013. Surface: CPL (continuous pressure laminate) in 0.5mm thickness in melamine finish. The PLB will be confirming to E-1 Grade as per the JIS A 5905-2003

standards and approved shade confirming to IS-12823:1990.The back of storage will be made in 9 MM PLB (Pre laminated board) with the density of 680kg/m³ and 18 mm thick

one side pre-laminate board confirming to IS 12406 : 2013. Surface: CPL ( continuous pressure laminate) in 0.5mm thickness in melamine finish. Storgage will be provided with

edge banding 2 mm thick PVC edge band will confirm to DIN 68861 for resistance to clearers. The Hot melt glue used for fixing the PVC edge band should have ISO 9001-

2015 quality certification and confirm to ASTM D 4499 standards for viscosity and thermal stability. The edge band material should have Shore D hardness of 79± 4. storage will

have two adjustable shelves making 3 compartments.The shutters are fitted with auto closing hinges.Central locking system , levellers & other necessary hardware are

priovided.Handles will be hand grooved.

SIZE - 1200W X 600D X 750/ 350HT

MAIN SCREEN:- ALUMINIUM 30MM SCREEN WITH SPLIT TILES(Half Fabric magnetic and half Glass marker)

PRIVACY SCREEN:- DETACHABLE SCREEN(6mm Acrylic)

PASSAGE AND FRONT MODESTY:-12mm prelam

Specifications:

Table Top: 25mm thick Pre laminate particle board with 2mm PVC edge lipping on all exposed edges

Screen: 18mm fabric screen with Al Trims having magnetic strip fixed on the studs with gap of 50/75mm from the table top edges Support: MS powder coated motorised height

adjustable under structure with height varying from 600-1250mm.

Wire Management: 450mm Alumninium flip up and provision to mount swicthes and sockets on PVC cable dump & vertebra for wire uptake from MS cable tray fixed below the

under structure and wire entry cover for wire intake from floor to cable tray

MOBILE PEDESTAL:-400W X 450D X 600HT

The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick.

The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller

channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one

Digitally signed by SAKET

COURT ROOM TABLE

SIZE:-1500W X 750D X 750HT

Table; Made of 25mm thick prelaminated particle board of approved shade confirming to E1 norms. All the edges of workstation surface shall be provided with machine pressed

2mm thick PVC lipping.

Leg: The Leg is constructed by 50Sq-16g ERW tube acts as vertical member & Rect.50x25-16g ERW tube which acts as horizontal member. Rectangle tube which is a

horizontal member of the leg is attached with two verticals on either ends by MIG welding. MIG (Co2) welding is done on inner faces of the tubes to take care of aesthetics of leg.

Leg shoe is made from Acrylonitrile butadiene styrene which is insert moulded with zinc blue plated M10 – nuts for additional stiffness. The levellers can be adjusted from 0-

25mm height provided with leveling bolts / screws to take care of undulations in the floor level.

8 Beams; Legs are connected using cross beams made of 40 x 20 16 gauge rectangular tube and connected to legs with aluminium die cast wing connectors tight fit to leg beam 6 Nos ₹ 13,863.00 ₹ 83,178.00

alloted with 4 holes.

BOARD ROOM / CONFERENCE ROOM AND MEETING TABLE FOR CHAIRPERSON AND MEMBER - 1

Table Top: 25mm thick pre laminated particle board with 2mm PVC edge lipping & 8mm color glass covered with aluminium beeding in anodised finish

End Legs: 50mm thick pre laminated particle board with 2mm PVC edge lipping & 3 equal drawer pedetal with aluminium die cast arms.

Modesty Panel: 18mm thk pre lam board with 2mm PVC edge lipping of 450mm Ht.

Wire Management:

* Continuous PVC Cable Tray with provision to mount switches and sockets as per client requirement.

* Vertical wire entry cover for wire uptake from floor to cable tray and Turn connect for swicth access.

9 * Turn connect Configuration - Standard switch configuration no deviation

1 switch, 2 universal socket,

1 data for network, 1 data for telephone,

1 usb for data, 2 usb for power, 1 HDMI,

1 VGA, 1 Audio jack Starter cable

LARGE CONFERNCE ROOM

MAIN TABLE :- 2400W X 750D X 750HT (QTY-01)

SIDE TABLE:- 1500W X 750D X 750HT (QTY-24)

Table top - The work surface will be in PLB 25mm thick one side pre-laminate board confirming to IS-14587:1998. The density of PLB will be 680kg/m³. Surface: CPL(

continuous pressure laminate) in 0.5mm thickness in melamine finish. The PLB will be confirming to E-1 Grade as per the JIS A 5905-2003 standards and approved shade

confirming to IS-12823:1990.PVC edge band will be minimum 2 mm thick, will be imported, quality confirming to DIN 68861, 53388 standards. The edge band will be fixed to the

work surface edges all round with Imported Hot melt Glue confirming to ISO 9001- 2008 and certified by ANSI for quality.

Under Structure - • The MS supports are made of 50 x50mm square ERW tubes- 16g with levelers to cater for floor undulations- +/- 20 mm. ERW Tube confirming to IS 4923 :

1997 – 16g. Main leg members will be connected through a horizontal member size 1.6mm thk, 50x25 cold formed ERW tube confirming to IS 4923: 1997. The vertical and the

horizontal tubes will be welded with CO2 MIG welding process confirming to IS 816 and ISO 9692-2. The leg will be fabricated using Argon & Co2 gas mixture on a Robotic

10 welding machine to ensure adequate welding strength with consistency.• The legs will be connected with Cross beams to take care of the bending stress catering.• The number 2 Nos ₹ 5,34,186.00 ₹ 10,68,372.00

of cross beams will be based on the depth of the table. The Cross Beams are made of 40x20 mm ERW tubes- 16 g.

• The Engineering plastic components will be made with Acrylonitrile butadiene styrene (ABS) which are confirming to ASTM D256 for Izod Impact (1/4”) for Leg shoe and

Wire Management - 1 NOS of 450 mm Flipup for Power and Data and Vetebra for Wire Entry.Cable Trays will be provided when the cable access is required from the top

through ‘Flip ups”. The Switch/socket slots are provided as a part of the “Flip Up” design just below the flip covers.

The “flip up” should be made in aluminum flip covers with soft closing arrangement. The “Flip up” cover will be anodized in Silver grey finish to 20 microns confirming to IS

MAIN TABLE :- 1350MM@DIA X 750HT

Table Top: 25mm thick Pre laminate particle board with 2mm PVC edge lipping on all exposed edges(Straight/Reverse waterfall edge)

End Legs : Powder coated Al die casted Enrich legs

Modesty Panel: 18mm thk pre lam board with 2mm PVC edge lipping of 450mm Ht.

Wire Management: 450mm Aluminium Flip Up and provision to mount swicthes and sockets on PVC cable dump and Vertical wire entry cover or vertebra for wire uptake from

floor to cable dump

MAIN TABLE :- 900W X 900D X 750HT

Table top - The work surface will be in PLB 25mm thick one side pre-laminate board confirming to IS-14587:1998. The density of PLB will be 680kg/m³. Surface: CPL(

continuous pressure laminate) in 0.5mm thickness in melamine finish. The PLB will be confirming to E-1 Grade as per the JIS A 5905-2003 standards and approved shade

confirming to IS-12823:1990.PVC edge band will be minimum 2 mm thick, will be imported, quality confirming to DIN 68861, 53388 standards. The edge band will be fixed to the

work surface edges all round with Imported Hot melt Glue confirming to ISO 9001- 2008 and certified by ANSI for quality.

Under Structure - • The MS supports are made of 50 x50mm square ERW tubes- 16g with levelers to cater for floor undulations- +/- 20 mm. ERW Tube confirming to IS 4923 :

1997 – 16g. Main leg members will be connected through a horizontal member size 1.6mm thk, 50x25 cold formed ERW tube confirming to IS 4923: 1997. The vertical and the

horizontal tubes will be welded with CO2 MIG welding process confirming to IS 816 and ISO 9692-2. The leg will be fabricated using Argon & Co2 gas mixture on a Robotic

12 welding machine to ensure adequate welding strength with consistency.• The legs will be connected with Cross beams to take care of the bending stress catering.• The number 2 Nos ₹ 10,266.00 ₹ 20,532.00

of cross beams will be based on the depth of the table. The Cross Beams are made of 40x20 mm ERW tubes- 16 g.

• The Engineering plastic components will be made with Acrylonitrile butadiene styrene (ABS) which are confirming to ASTM D256 for Izod Impact (1/4”) for Leg shoe and

Wire Management - 1 NOS of 450 mm Flipup for Power and Data and Vetebra for Wire Entry.Cable Trays will be provided when the cable access is required from the top

through ‘Flip ups”. The Switch/socket slots are provided as a part of the “Flip Up” design just below the flip covers.

The “flip up” should be made in aluminum flip covers with soft closing arrangement. The “Flip up” cover will be anodized in Silver grey finish to 20 microns confirming to IS

Digitally signed by SAKET

NOMAD TABLE:- 1560L X 500D X 1800H

NoMad is a movable writing board that comes with magnetic writing/marker board on one side and with a option to mount monitor on other side with inbuilt wiring. Size of the

marker board is 1200x900mm. (Incase of 1560L x 1800H, the marker board size comes to 1500L x 900H)

Product has storage underneath marker board that is made from 18mm Prelam particle board with edge binding, comes with shutters on either ends and a open shelf at centre,

provision to keep Marker Pens/Duster / TV remote etc.

The vertical poles of NoMad are from Spl. profile MS tube, Feet are high pressure aluminium diecast parts fitted with best quality castors of Dia 60mm. 02 metal hooks are

offered with a pole to keep wires in place when not in use.

NoMad comes with 02 HDMI & a 3 mtr length 3 core wire, a power doc fixed on top of storage has 2 sockets, 1 switch & 2 USB.

All Metal & Diecast parts comes with powder coating finish.

13 All Plastics are in TML grey colour. 7 Nos ₹ 53,218.00 ₹ 3,72,526.00

The design of the product is modular, easy to assemble, easy to move.

MAIN TABLE :- 900W X 450D X 1200HT

Table top - The work surface will be in PLB 25mm thick one side pre-laminate board confirming to IS-14587:1998. The density of PLB will be 680kg/m³. Surface: CPL(

continuous pressure laminate) in 0.5mm thickness in melamine finish. The PLB will be confirming to E-1 Grade as per the JIS A 5905-2003 standards and approved shade

confirming to IS-12823:1990.PVC edge band will be minimum 2 mm thick, will be imported, quality confirming to DIN 68861, 53388 standards. The edge band will be fixed to the

work surface edges all round with Imported Hot melt Glue confirming to ISO 9001- 2008 and certified by ANSI for quality.

Under Structure - • The MS supports are made of 50 x50mm square ERW tubes- 16g with levelers to cater for floor undulations- +/- 20 mm. ERW Tube confirming to IS 4923 :

1997 – 16g. Main leg members will be connected through a horizontal member size 1.6mm thk, 50x25 cold formed ERW tube confirming to IS 4923: 1997. The vertical and the

horizontal tubes will be welded with CO2 MIG welding process confirming to IS 816 and ISO 9692-2. The leg will be fabricated using Argon & Co2 gas mixture on a Robotic

welding machine to ensure adequate welding strength with consistency.• The legs will be connected with Cross beams to take care of the bending stress catering.• The number 89

of cross beams will be based on the depth of the table. The Cross Beams are made of 40x20 mm ERW tubes- 16 g.

• The Engineering plastic components will be made with Acrylonitrile butadiene styrene (ABS) which are confirming to ASTM D256 for Izod Impact (1/4”) for Leg shoe and

Wire Management - 1 NOS of 450 mm Flipup for Power and Data and Vetebra for Wire Entry.Cable Trays will be provided when the cable access is required from the top

through ‘Flip ups”. The Switch/socket slots are provided as a part of the “Flip Up” design just below the flip covers.

The “flip up” should be made in aluminum flip covers with soft closing arrangement. The “Flip up” cover will be anodized in Silver grey finish to 20 microns confirming to IS

EXECUTIVE DINNING

MAIN TABLE :- 1350MM@DIA X 750HT

Under-structure is made from solid wood ie., in Beach wood, finished with clear PU coating.

Legs are fixed with height adjustable levellers for leveling, based on floor undulation upto 10mm.

For Cafeterias - 18mm thk prelaminated Hydrosheild table top. .

MAIN TABLE :- 1800W X 800D X 750HT

Table Top:The surface will be in PLB 25mm thick one side pre-laminate board confirming to IS-14587:1998. The density of PLB will be 680kg/m³. Surface: CPL( continuous

pressure laminate) in 0.5mm thickness in melamine finish. The PLB will be confirming to E-1 Grade as per the JIS A 5905-2003 standards and approved shade confirming to IS-

Under Structure- The MS supports are made of 50 x50mm square ERW tubes- 16g with levelers to cater for floor undulations- +/- 20 mm. ERW Tube confirming to IS 4923 :

1997 – 16g. Main leg members will be connected through a horizontal member size 1.6mm thk, 50x25 cold formed ERW tube confirming to IS 4923: 1997. The vertical and the

horizontal tubes will be welded with CO2 MIG welding process confirming to IS 816 and ISO 9692-2. The leg will be fabricated using Argon & Co2 gas mixture on a Robotic

16 welding machine to ensure adequate welding strength with consistency.• The legs will be connected with Cross beams to take care of the bending stress catering.• The number 3 Nos ₹ 19,553.00 ₹ 58,659.00

of cross beams will be based on the depth of the table. The Cross Beams are made of 40x20 mm ERW tubes- 16 g.

MAIN TABLE :- 1200W X 800D X 750HT

Table Top:The surface will be in PLB 25mm thick one side pre-laminate board confirming to IS-14587:1998. The density of PLB will be 680kg/m³. Surface: CPL( continuous

pressure laminate) in 0.5mm thickness in melamine finish. The PLB will be confirming to E-1 Grade as per the JIS A 5905-2003 standards and approved shade confirming to IS-

Under Structure- The MS supports are made of 50 x50mm square ERW tubes- 16g with levelers to cater for floor undulations- +/- 20 mm. ERW Tube confirming to IS 4923 :

1997 – 16g. Main leg members will be connected through a horizontal member size 1.6mm thk, 50x25 cold formed ERW tube confirming to IS 4923: 1997. The vertical and the

horizontal tubes will be welded with CO2 MIG welding process confirming to IS 816 and ISO 9692-2. The leg will be fabricated using Argon & Co2 gas mixture on a Robotic

17 welding machine to ensure adequate welding strength with consistency.• The legs will be connected with Cross beams to take care of the bending stress catering.• The number 7 Nos ₹ 16,992.00 ₹ 1,18,944.00

of cross beams will be based on the depth of the table. The Cross Beams are made of 40x20 mm ERW tubes- 16 g.

RACK FOR LIBRARY

SIZE:- 900W x 370D x 1950H

Upright - MS 40 x 40 x 1.6 Tube.

Side Profile - MS Powder coated metal profile of 1.6mm with Acrylic pouch.

Band : Made of MS Powder coated metal 1.6mm

Shelves - Made of MS powder coated metal 1.2mm, supported with brackets.

Back Panel - Made of MS Powder coted metal 0.8mm.

Top panel , Side Panel & Bottom Panle - Made of 18mm thk PLT.

Digitally signed by SAKET

HIGH BACK CHAIR FOR CHAIRPERSON

The separate seat and back shall be a durable, breathable Pellicle material stretched within a carrier ring and fitted into an outer frame. The Pellicle material shall be a woven

blend of colored polyester yarn with Hytrel elastomeric polyester of various stiffness, which is a high- performance polymer.Right and left swing arms shall attach the seat and

back to the tilt mechanism, support the arms, and provide an attachment location for the height control. The swing arms shall be die-cast aluminum with either a polished, smooth

or wrinkle-coat powder-coat epoxy finish. The swing arms shall attach with 2 screws to each side of the back frame and with ball joints to the seat.The lumbar pad shall be a

nylon bow with integral attachment clip features on each side. A flexible Hytrel strap shall be stretched across the width of the lumbar bow, connecting with a hook and loop. A 5

½” high x 4 ¼” wide support pad made of nylon snaps to the center of the strap with 4 snaps.The fixed and height adjustable arms shall have a glass filled nylon arm support and

is attached to the yoke with two carbon steel screws. The height adjustable arm with pivot shall have a glass filled nylon arm support. An acteal detent insert snap fits into the

pivot only support and is attached to the yoke with a stainless steel pivot spring and two carbon steel screws. The fully adjustable arm has a carbon steel support plate that slides

between an acetal detent plate and acetal pivot block.The tilt mechanism shall contain 2 fiberglass leaf springs, a nylon gear-driven tension adjustment and a die-cast aluminum

front and rear housing with either a polished, smooth or wrinkle-coat powder-coat epoxy finish. A 3-piece ABS cover shall snap together to enclose the mechanism.The chair

19 base shall house a unitized pneumatic seat height adjustment mechanism contained in 2 steel tubes; an inner tube shall slide and rotate in an acetal bushing within an outer 1 Nos ₹ 1,12,100.00 ₹ 1,12,100.00

tube. The outer tube shall be coated black and shall have a tapered end that will be pressed into the base and an upper end that shall be pressed into the tilt mechanism.Seat

height shall be controlled by a glass-filled nylon lever and paddle mounted on the right swing arm.The fully adjustable arms support to pivot to 9 different positions and slide fore-

aft to 10 positions. The arm shall be adjustable to 16° outward and 16° inward by applying pressure to the side of the arm. The arm shall slide fore-aft 2.5”

VISITOR CHAIR FOR CHAIRPERSON

Assembly option: Fully assembled, Size: Size B, Height adjustment: Standard height range, Tilt option: Tilt limiter and forward tilt, Arms: Height adjustable arms, Armpads: Non-

upholstered armpads

Back support: 8Z Pellicle only - SZS, Frame finish: Graphite - G1, Chassis finish: Graphite - G1, Base finish: Graphite - G1, Castors / glides: 65mm castors (carpet) - BB,

Armpad colour: Black - BK, Pellicle: Graphite - 23103

The separate seat and back shall be a durable, breathable Pellicle material stretched within a carrier ring and fitted into an outer frame. The Pellicle material shall be a woven

blend of colored polyester yarn with Hytrel elastomeric polyester of various stiffness, which is a high- performance polymer.Right and left swing arms shall attach the seat and

back to the tilt mechanism, support the arms, and provide an attachment location for the height control. The swing arms shall be die-cast aluminum with either a polished, smooth

or wrinkle-coat powder-coat epoxy finish. The swing arms shall attach with 2 screws to each side of the back frame and with ball joints to the seat.The lumbar pad shall be a

nylon bow with integral attachment clip features on each side. A flexible Hytrel strap shall be stretched across the width of the lumbar bow, connecting with a hook and loop. A 5

½” high x 4 ¼” wide support pad made of nylon snaps to the center of the strap with 4 snaps.The fixed and height adjustable arms shall have a glass filled nylon arm support and

20 is attached to the yoke with two carbon steel screws. The height adjustable arm with pivot shall have a glass filled nylon arm support. An acteal detent insert snap fits into the 4 Nos ₹ 88,500.00 ₹ 3,54,000.00

pivot only support and is attached to the yoke with a stainless steel pivot spring and two carbon steel screws. The fully adjustable arm has a carbon steel support plate that slides

between an acetal detent plate and acetal pivot block.The tilt mechanism shall contain 2 fiberglass leaf springs, a nylon gear-driven tension adjustment and a die-cast aluminum

front and rear housing with either a polished, smooth or wrinkle-coat powder-coat epoxy finish. A 3-piece ABS cover shall snap together to enclose the mechanism.The chair

base shall house a unitized pneumatic seat height adjustment mechanism contained in 2 steel tubes; an inner tube shall slide and rotate in an acetal bushing within an outer

tube. The outer tube shall be coated black and shall have a tapered end that will be pressed into the base and an upper end that shall be pressed into the tilt mechanism.Seat

height shall be controlled by a glass-filled nylon lever and paddle mounted on the right swing arm.The fully adjustable arms support to pivot to 9 different positions and slide fore-

aft to 10 positions. The arm shall be adjustable to 16° outward and 16° inward by applying pressure to the side of the arm. The arm shall slide fore-aft 2.5”

HEAD CHAIR FOR MEMBERS / SEC

MODEL:- MIRRA 2

Assembly option: Fully assembled, Height adjustment: Standard height, Tilt option: Tilt limiter & forward tilt, Arms: Fully adjustable arms, Armpad: Vinyl armpads, Seat depth:

FlexFront® adjustable, Back material: Butterfly™ suspension back

Back support: Adjustable lumbar support - AJ, Base / frame finish: Graphite - G1, Castors / glides: 65mm castors (hard floor/carpet) - C7, Back finish: Graphite - G1, Butterfly

back colour: Black - 8M17, Armpad colour: Black - BK, AireWeave™ 2 suspension seat: Graphite - 1A703

1. Harmonic™ 2 Tilt The tilt enables natural, balanced movement through

a range of postures. 2. Butterfly Back™ The Butterfly back combines the comfort of upholstery with the strength of polymer to provide pressure distribution from sacrum to the

upper thoracic regions of the spine. . 4. PostureFit®

PostureFit supports your spine at its lowest point, the sacrum, and reinforces your pelvis, preventing

21 slouching and fatigue while you sit. 5. Optional Height-Adjustable Lumbar Support The height-adjustable lumbar support provides an added level of spinal support and comfort 5 Nos ₹ 49,560.00 ₹ 2,47,800.00

for the Lumbar region.

6. AireWeave™ Seat Suspension The seat suspension conforms to your shape, distributes your weight evenly, and keeps heat from building up as you sit.

VISIOTR CHAIR FOR MEMBERS / SEC

BIFMA X5.1-2017 American National Standards Institute/Business and Institutional Furniture Manufacturer’s Association (ANSI/BIFMA) Office chair QB/T 2280-2016 The light

industry standard of PRC.The upholstered contoured seat shall be molded polypropylene insert with molded polyurethane foam. The foam shall have a nominal 50mm thickness

and have waterfall edges. Fabric is applied nonbonded. When chairs are refurbished, the complete seat assembly can be replaced. The foam firmness is 45+/-5 degree (LX-F

sclerometer), and its density is 55-60kg/m3.The back sub-assembly shall consist two layers: backframe, mesh(or upholstery). The backframe shall be polyamide 6 + 30% glass

fiber. Glass-reinforced nylon results in materials possessing better tensile and flexural strengths than the base resin. It was regarded to be almost a replacement for some die

casting alloys. The adjustable arms can be adjusted in width and in height. The inside width is adjusted through the quick release button on the horizontal lever. The arms shall

have an arm support stem of glass-filled polyamide 6 with over moulded polyurethane arm pads.Chair should have Green Guard certificate nad BIFMA certified.

Digitally signed by SAKET

HIGH BACK CHAIR FOR ADVISORS

Assembly option: Assembled, Back type: Interweave 2 suspension back, Height adjustment: Standard height, Tilt option: Self adj tilt with 3P tilt lock, Arms: Height adjustable

arms, Seat depth: Adjustable seat depth

Back support: Adjustable lumbar with sacral support - AJ, Base / frame finish: Black base/black frame - BK, Suspension finish: Iceberg - 36501, Castors: 2 1/2" hard caster,

black yoke, carpet only - BB, Fabric type: Medley 1HA - 1HA#, Fabric colour: Stone (61002) - 1HA01 The upholstered back option offers an array of textiles with a polymer

outer back shell. Interweave 2 is a high-performing suspension material that delivers increased comfort, breathability, built-in sacral support, and total spinal support. The

TriFlex™ polymer back is 100% engineered polymer that offers flexible and continuous support including built-in sacral support and meets rigorous cleaning protocols.

Interweave 2 suspension back and TriFlex polymer back chairs come standard with passive sacral support and are available with optional adjustable lumbar support with sacral

support.The chair has a 5-star base and 2 pneumatic height adjustment options.

The back frame/outer shell, arms, arm pads and base finishes are black

or mineral.The synchronous with tilt limiter and seat angle allows the user to set

tilt range and select a 5° forward seat angle.

VISIOTR CHAIR FOR ADVISORS

BIFMA X5.1-2017 American National Standards Institute/Business and Institutional Furniture Manufacturer’s Association (ANSI/BIFMA) Office chair QB/T 2280-2016 The light

industry standard of PRC.The upholstered contoured seat shall be molded polypropylene insert with molded polyurethane foam. The foam shall have a nominal 50mm thickness

and have waterfall edges. Fabric is applied nonbonded. When chairs are refurbished, the complete seat assembly can be replaced. The foam firmness is 45+/-5 degree (LX-F

sclerometer), and its density is 55-60kg/m3.The back sub-assembly shall consist two layers: backframe, mesh(or upholstery). The backframe shall be polyamide 6 + 30% glass

fiber. Glass-reinforced nylon results in materials possessing better tensile and flexural strengths than the base resin. It was regarded to be almost a replacement for some die

casting alloys. The adjustable arms can be adjusted in width and in height. The inside width is adjusted through the quick release button on the horizontal lever. The arms shall

have an arm support stem of glass-filled polyamide 6 with over moulded polyurethane arm pads.Chair should have Green Guard certificate nad BIFMA certified.

Digitally signed by SAKET

HIGH BACK CHAIR FOR JOINT ADVISOR

The 2 back support frames shall be injection-molded glass-reinforced polypropylene, reinforced with a stamped steel weldment. The back shall be secured to the frames in 2

locations by injection-molded acrylonitrile butadiene styrene (ABS) fastening caps and in 2 locations by bolts; and the frames shall be attached to the back of the tilt with 4

bolts.The optional upholstered cushion seat shall have a seat cushion of injection-molded, mediumdensity, cold-cured polyurethane foam over a polypropylene inner shell. The

foam shall have a nominal thickness of 1 ¾” in the back of the seat pan area to provide greater support in the user’s ischial tuberosities area. The seat shall have waterfall

edges. The foamed shell shall be fully upholstered and the fabric shall not be bonded to the foam.Chairs shall be available with no arms, fixed arms, and adjustable arms. Each

arm shall have a steel armstrap, an injection-molded glass-reinforced nylon armpad support and arm stem, and an armpad of self-skinning urethane foam molded over an ABS

insert. Each armpad shall be attached to an armpad support, each armpad support shall be attached to the armstrap, and the armstrap shall be bolted to the chair’s tilt.The

pneumatic seat-height-adjustment mechanism shall be housed within a steel tube. The tube shall slide and rotate in a bushing within the steel base weldment. The top end of the

tube shall be pressed into the tilt mechanism and the lower end shall be inserted into the 5-star base. The chair shall be available with 2 1/2” diameter casters . Casters for use

on carpet only shall have a steel stem and black nylon wheels and yoke.Each arm shall have a steel armstrap, an injection-molded glass-reinforced nylon armpad support and

25 arm stem, and an armpad of self-skinning urethane foam molded over an ABS insert.Chair is ANSI/BIFMA and Green Guard Certified.Celle is backed by 12-year, 3-shift 10 Nos ₹ 47,000.00 ₹ 4,70,000.00

VISITOR CHAIR FOR JOINT ADVISOR/ COURT ROOM

BIFMA X5.1-2017 American National Standards Institute/Business and Institutional Furniture Manufacturer’s Association (ANSI/BIFMA) Office chair QB/T 2280-2016 The light

industry standard of PRC.The upholstered contoured seat shall be molded polypropylene insert with molded polyurethane foam. The foam shall have a nominal 50mm thickness

and have waterfall edges. Fabric is applied nonbonded. When chairs are refurbished, the complete seat assembly can be replaced. The foam firmness is 45+/-5 degree (LX-F

sclerometer), and its density is 55-60kg/m3.The back sub-assembly shall consist two layers: backframe, mesh(or upholstery). The backframe shall be polyamide 6 + 30% glass

fiber. Glass-reinforced nylon results in materials possessing better tensile and flexural strengths than the base resin. It was regarded to be almost a replacement for some die

casting alloys. The adjustable arms can be adjusted in width and in height. The inside width is adjusted through the quick release button on the horizontal lever. The arms shall

have an arm support stem of glass-filled polyamide 6 with over moulded polyurethane arm pads.Chair should have Green Guard certificate nad BIFMA certified.

MID CHAIR FOR DEPUTY ADVISIORS/ PA/ PS

BIFMA X5.1-2017 American National Standards Institute/Business and Institutional Furniture Manufacturer’s Association (ANSI/BIFMA) Office chair QB/T 2280-2016 The light

industry standard of PRC.The upholstered contoured seat shall be molded polypropylene insert with molded polyurethane foam. The foam shall have a nominal 50mm thickness

and have waterfall edges. Fabric is applied nonbonded. When chairs are refurbished, the complete seat assembly can be replaced. The foam firmness is 45+/-5 degree (LX-F

sclerometer), and its density is 55-60kg/m3.The back sub-assembly shall consist two layers: backframe, mesh(or upholstery). The backframe shall be polyamide 6 + 30% glass

fiber. Glass-reinforced nylon results in materials possessing better tensile and flexural strengths than the base resin. It was regarded to be almost a replacement for some die

casting alloys. The adjustable arms can be adjusted in width and in height. The inside width is adjusted through the quick release button on the horizontal lever. The arms shall

have an arm support stem of glass-filled polyamide 6 with over moulded polyurethane arm pads.Chair should have Green Guard certificate nad BIFMA certified.

VISITOR CHAIR FOR DEPUTY ADVISIORS/ PA/ PS

BIFMA X5.1-2017 American National Standards Institute/Business and Institutional Furniture Manufacturer’s Association (ANSI/BIFMA) Office chair QB/T 2280-2016 The light

industry standard of PRC.The upholstered contoured seat shall be molded polypropylene insert with molded polyurethane foam. The foam shall have a nominal 50mm thickness

and have waterfall edges. Fabric is applied nonbonded. When chairs are refurbished, the complete seat assembly can be replaced. The foam firmness is 45+/-5 degree (LX-F

sclerometer), and its density is 55-60kg/m3.The back sub-assembly shall consist two layers: backframe, mesh(or upholstery). The backframe shall be polyamide 6 + 30% glass

fiber. Glass-reinforced nylon results in materials possessing better tensile and flexural strengths than the base resin. It was regarded to be almost a replacement for some die

casting alloys. The adjustable arms can be adjusted in width and in height. The inside width is adjusted through the quick release button on the horizontal lever. The arms shall

have an arm support stem of glass-filled polyamide 6 with over moulded polyurethane arm pads.Chair should have Green Guard certificate nad BIFMA certified.

MID CHAIR FOR WORKSTATION/ RECEPTION/ LARGE CONFERENCE ROOM/ VIDEO CONFERENCE ROOM/ OTHERS

BIFMA X5.1-2017 American National Standards Institute/Business and Institutional Furniture Manufacturer’s Association (ANSI/BIFMA) Office chair QB/T 2280-2016 The light

industry standard of PRC.The upholstered contoured seat shall be molded polypropylene insert with molded polyurethane foam. The foam shall have a nominal 50mm thickness

and have waterfall edges. Fabric is applied nonbonded. When chairs are refurbished, the complete seat assembly can be replaced. The foam firmness is 45+/-5 degree (LX-F

sclerometer), and its density is 55-60kg/m3.The back sub-assembly shall consist two layers: backframe, mesh(or upholstery). The backframe shall be polyamide 6 + 30% glass

fiber. Glass-reinforced nylon results in materials possessing better tensile and flexural strengths than the base resin. It was regarded to be almost a replacement for some die

casting alloys. The adjustable arms can be adjusted in width and in height. The inside width is adjusted through the quick release button on the horizontal lever. The arms shall

have an arm support stem of glass-filled polyamide 6 with over moulded polyurethane arm pads.Chair should have Green Guard certificate nad BIFMA certified.

Digitally signed by SAKET

SOFA FOR MEMBER + EXECUTIVE + RECEPTION (2 SEATER)

SIZE -1800W X 720D X 730HT

This is the ultimate soft-seating system. Designed to be lightweight, low and open platform. It can be configured in myriad ways. Benches, one-, two- and three-seater options,

built-in surfaces and functional occasional items can come together to create the ideal

counterbalance to personal workstations, thus supporting collaboration, naturally.

Modularity was a key consideration in the design for Sabha. The understructure frame

is consistent across all products within the collection, enabling the same platform to connect with all the soft and wood elements on top via clamps, which can be easily

tightened and untightened for easy

30 installation and dismantling. 18 Nos ₹ 1,32,000.00 ₹ 23,76,000.00

SOFA FOR CHAIRPERSON (3 SEATER)

The Outline Sofa adds new perspectives to the classic Scandinavian design sofas of the 1960's, marrying the ideals of simplicity and function into one. With the design taking its

name from its strong outline of a sofa, the Outline Series is clean and elegant on the outside with a deep seat and soft cushioning on its inside. The Outline Series has an

expression that is at once elegant yet timeless, elevated by its lines referencing architectural shapes alongside its curved armrests, giving the design a distinct appearance

across various sizes and variants.

Additional Information

A Power Outlet including USB and USB-C charger can be added to the Outline Sofa Series. The Power Outlet is available in an EU, US and UK version. Please note that

Muuto does not offer installation of the Power Outlet into any Muuto products.

Variant:Hallingdal 166/Black

Base color:Black

31 Base material:Powder Coated Aluminum 2 Nos ₹ 3,32,000.00 ₹ 6,64,000.00

Upholstery type:Hallingdal

Upholstery color:166

Seat height:40 cm

Seat depth:62 cm

SOFA FOR ADVISORS AND RECEPTION AREA

Seat Foam: The sofa is made up of 100% pure leather. The structure is made up of silver wood and pine wood. The Seat is made of PU Foam with Density 32 to 40 +/- 2 kg/cu

mtr. Seat is upholstered with 100% pure leather. Back Foam: The Back is made of PU Foam with Density 32 to 40 +/- 2 kg/cu, Back is upholstered with 100% pure leather.

Unterstructure is made up of silver wood or pine wood, 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Legs should be

made up of solid wood having pu matt finish.

EXECUTIVE CAFÉ CHAIR

Seat is made out of 45mm molded foam in ergonomic shape. Upholstery: Cushion with pre moulded foam of 50 - 60 density Density -- 60 kg/m3 Hardness -- 16kgf at

25%.Cushioned Back with Leatherette/ Fabric Upholstery. Moulded fixed arms.Seat & Back are duly upholstered with High Grade Leatherette/ Fabric.Under-structure is made

from solid wood ie., in Beach wood, finished with clear PU coating. Legs are fixed with height adjustable levellers for leveling, based on floor undulation upto 10mm.

Chair is moulded from GF 20% Polypropylene conforming to ASTM D 638 STD & Complying to ROHS. Seat & back design will be integrated as a single unit. The chair shall be

injection moulded with 2500 tonnage press. The back will be designed with triangular structural trusses & narrowed at the top to provide strength & comfort to the chair with good

air circulation to the user. The back should be designed to provide ergonomic comfort with precise curvature to offer good lumbar support. The seat profile should be designed

with water fall to provide necessary comfort in popliteal region.

34 The design of the chair will be provided with four U shaped legs ensuring good strength to the chair. 47 Nos ₹ 5,007.00 ₹ 2,35,329.00

CENTER TABLE FOR CHAIRPERSON/ MEMBERS ROOM

Size: 600DIAx450HT

METAL SLIMLINE BASE + MARBLE TOP

The top of the table shall be made up of 15mm thick marbel top bevelled shape. The top profile shall be in circular shape with bevelled edges. The top shall be supported on

vacuum caps situated over SS 202 grade pipe frame. The under structure shall have MS with shiny finish pipe frame . There shall be good quality PPCP shoe provided to avoid

35 scratches on the floor. 12 Nos ₹ 29,500.00 ₹ 3,54,000.00

SIDE TABLE FOR CHAIRPERSON/ MEMBERS ROOM

Size: 400DIA x 550(H)

METAL SLIMLINE BASE + MARBLE TOP

The top of the table shall be made up of 15mm thick marbel top bevelled shape. The top profile shall be in circular shape with bevelled edges. The top shall be supported on

vacuum caps situated over SS 202 grade pipe frame. The under structure shall have MS with shiny finish pipe frame . There shall be good quality PPCP shoe provided to avoid

36 scratches on the floor. 18 Nos ₹ 17,700.00 ₹ 3,18,600.00

Digitally signed by SAKET

CENTER TABLE FOR ADVISOR / JOINT ADVISOR

The top of the table shall be made up of 18mm thick marbel top bevelled shape. The top profile shall be in rectangular shape with bevelled edges. The top shall be supported on

vacuum caps situated over SS 202 grade pipe frame. The under structure shall have MS with shiny finish pipe frame . There shall be good quality PPCP shoe provided to avoid

scratches on the floor.

SIDE TABLE FOR ADVISOR / JOINT ADVISOR

Size: 600(W) x 600(D) x 505(H)

The top of the table shall be made up of 18mm thick marbel top bevelled shape. The top profile shall be in rectangular shape with bevelled edges. The top shall be supported on

vacuum caps situated over SS 202 grade pipe frame. The under structure shall have MS with shiny finish pipe frame . There shall be good quality PPCP shoe provided to avoid

38 scratches on the floor. 10 Nos ₹ 15,930.00 ₹ 1,59,300.00

CENTER TABLE FOR WAITING/ LOBBY/ RECEPTION

Center table with an overall size L 1200 X W 600 X H 425 mm. The top of the table shall be made up of 12mm thick toughened glass. The top profile shall be in square shape

with bevelled edges. The top shall be supported on vacuum caps situated over SS 202 grade pipe frame. The under structure shall have SS with shiny chrome finish pipe frame

having dia. 20-25.4mm with 2mm thick. There shall be good quality PPCP shoe provided to avoid scratches on the floor.Top glass is partial tempered glass.

CORNER TABLE FOR WAITING/ LOBBY/ RECEPTION

Corner table with an overall size L 600 X W 600 X H 505 mm. The top of the table shall be made up of 12mm thick toughened glass. The top profile shall be in square shape

with bevelled edges. The top shall be supported on vacuum caps situated over SS 202 grade pipe frame. The under structure shall have SS with shiny chrome finish pipe frame

having dia. 20-25.4mm with 2mm thick. There shall be good quality PPCP shoe provided to avoid scratches on the floor.Top glass is partial tempered glass.

COMPACTOR ONE WAY DEEP

DIMENSIONS BAY:-900W X 450D X 2420HT

Compactor Height from ground is 2420 mm (2305 body + 75 mm undercarriage + 40 mm channel system). Width of each bay will be 900mm, Depth of each bay will be 450 mm

for Single & 900 mm for double Bay.Complete construction of system is on knock down design for easy handling of material on site Rigid Upright frame made out of 1.2 mm

thick CRCA Steel box Pipe. Upright with 25 mm x 50 mm rectangular slotted Pipe. Each block consists of 1 Main unit & then Add-on units (0, 1,2,3,4,5 - depending on no. of

bays 1, 2, 3, 4, 5 & 6). Body units are bolted to undercarriage. Scalability Bays can be added Depth wise or width wise subsequently, if the need for additional filing is there.All

metal component are given antirust surface treatment & are powder coated with epoxy polyester powder. It involves 8 Tank treatment consisting of Degreasing, water rinse,

phosphating & dry off oven treatment. Final finish consists of epoxy polyester powder coating with a Dry Film Thickness of minimum 60 microns. The testing of paint is done for

various physical & chemical properties as per IS: 101.

The material is then oven baked with a controlled temperature of 180 deg.C to 200 deg.C.Grey, Beige, White, Brown, Black & Graphite, Single color or two tone

combinations.Number of shelves Each unit has 6 loading levels formed by 4 nos. adjustable shelves. 438 mm depth is available for storage of box file as well any odd size

Shelf thickness - 0.8 mm CRCA with stiffner with 80 kg UDL ( Uniformally Distributed Load) Shelves are mounted on support brackets & shelf level can be adjusted at 25 mm

Upright Rigid construction made out of 1.2 thk. CRCA Steel upright with 25 mm x 50 mm rectangular Pipe.

Clading 0.7 mm CRCA sheet metal panels .

Optional Doors- Optional doors with lock on each bay can be provided. 24

Trolley material - Steel pipe 1.6 mm thickness with smooth ball bearing wheel for load & guide wheel for anti tipping .

Track material - Aluminium track makes base of the compacta system rust proof against water contact.

Platform for walkway - 25 mm Laminated Particle board Platform for easy & safe entry exit from the walkways.

Sloping ramp - Aluminium Sloping ramp for easy trolley access & reduce tipping hazard.

Levelers - Easily Adjustable levelers to keep platform & track parallel on uneven surfaces.

Installation of Track -No Hacking of floor is required for easy dismantling & relocation of the system in case required.

Assembly of track - Complete track assembly is on self suspended design, suitable for any surface like cement, tiles, carpet etc Pulley Belt mechanism results in noise less & Oil

free operation.

Mechanism Handle Lock- Ergonomic Plastic handle with inbuilt safety lock mechanism.

Lock Central Locking on the last unit which will lock entire assembly.

RECEPTION TABLE :

Providing and fixing Rubber wood board reception tabel of 2700x900mm size as per thed etailed drawing and the reference image. The reception table shall incoporate all the

cnc cutting, drawers with channels icluding pop up boxes complete in all respect.

Digitally signed by SAKET

SCHEDULE OF QUANTITIES: SIGNAGE

S No Description Unit Qty Unit price DSR Amount Non-DSR Amount

1 RECEPTION 3D ACRYLIC SIGNAGE

Providing, fabricating and fixing of 3D Acrylic Letters raised 1.5 inches of required size and shape with

arrangement of screws in the letters itself for mounting on the walls or pasting using 3M VHP Tape. Fixing

complete as per directions of the engineer. The Sizes would be calculated in Sqft as per Logo Design

provided. Each 3 35,976.00 107928.00

Tentative Size 42"X60"

2 NAME SIGNAGE CHANGEABLE (All Floors)

Providing and fixing of Acrylic signage made of 3mm Acrylic with textured wood finish pasted /White milky

acrylic 3mm laser cut pasted on top with proper names/ Departments written using plottercut vinyl or laser cut

acrylic letters in approved colour.Inserting provision for changing names .Fixing provision using 3M VHP Each 50 1,967.00 98350.00

double sided tape as required.

Signage Size 12x5 inch

FIRE EVACUATION MAP / SIGN.

Providing and fixing of Clear Acrylic sandwich frame of 3mm & 2mm acrylic with Evacuation Plan Printed on

photoluminescent media and inserted between the two frames. Should be fixed on the wall using 4 Screw/ SS Each 5 2,673.00 13365.00

studs. Size 12 inch x 17 inch

4 FIRE ESCAPE EDGE-LIT SIGNAGE

Providing and fixing of Edge-Lit signage with battery backup. Made from acrylic sheet of 8 mm thickness

laser engraved, Transformer to be inbuilt. Maintenance - free sealed nickel cadmium battery included •

120V/277V AC Operation • Crystal clear acrylic face panel• Engraved letters increase visibility • Anodized

aluminum faceplate • Field applied chevron directional indicators simplify installation • Long life, energy- Each 5 3,289.00 16445.00

saving LED lamps • Dual-voltage 120V/277V AC Operation • UL listed. To be installed at stairs entry. Size

5 FIRE SAFETY SIGNAGE

Providing fabricating and fixing of signage 05 mm thick Acrylic / Sun board sheet at base with

photoluminescent film self adhesive & colored vinyl ( Red/Green) Plotter cut and pasted on top. Both side /

Single Side facing Complete including fixing on wall with screws and washers or hanging on ceiling with GI

chain/GI Bar complete as per technical specifications and directions of Engineer.

Photoluminescent signages Each 5 536.00 2680.00

TOTAL 238768.00

36 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: LANDSCAPE

Image Description Unit Qty Rate DSR Amount Non DSR Amount

MossWall - Customised

“Wall Panel - Plain; Supply, Testing and

Commissioning of maintenance free Moss Wall

of size 600 x 400 mm panel. The plant shall be

for indoor use only and requires no Direct Sun

Light or Watering / Spraying of water. It is

1 certified for sound absobtion rate; fire resistance Sqm 10 57,653.00 5,76,530.00

and has a very hostile environment for

reproduction of insects. Please ensure 40%

Humidity at all times. It does not require any

trimming as well hence a maintenance free

Make: Verde Profilo, Italy

Providing & fixing Artificial silk plants with

combination 3 or 4 types uniformaly ditributed

plants on wall as well as ceilig suspended

creepers with necessary wire or hangin

arranement included. Plants which ultraviolet

2 blocking chemicals are impregnated into the Sqm 20 6,214.00 1,24,280.00

materials during the manufacturing process.

These chemicals are blended with the plastic or

PVC parts Installation Installation is done on

Waterproof ply board with staple gun machine.

Providin & fixing Artificial silk plants with

combination 3 or 4 types uniformaly ditributed

plants on wall as well as ceilig suspended

creepers with necessary wire or hangin

arranement included. Plants which ultraviolet

3 blocking chemicals are impregnated into the Sqm 15 2,370.00 35,550.00

materials during the manufacturing process.

These chemicals are blended with the plastic or

PVC parts Installation Installation is done on

Waterproof ply board with staple gun machine.

Supply of textured stone or solid finished, light

weight of any shape: round/ oval/ rectangular/

conical/ elliptical)and color: beige/ white/ grey/

black) full bodied, exterior grade, joint/ layer free,

homogeneous planters made with premium

quality LLDPE polymer manufactured with

precision rotational moulding process. The

planters shall be made of 100% recyclable

4 content, industrial grade quality polymer, non-

metallic, shock proof, asbestos and glass fiber

free compounds. Planters shall be rust proof, UV-

resistant, anti-frost, no peeling and easy to

clean. OEM / authorized supplier to provide 1

year warranty against fading & any

manufacturing defect. Design, color and size as

Plantation: Supply and installation of Natural

Plant with sand, fertilizer etc.

37 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: GAS SUPPRESSION SYSTEM

S No Description Qty Unit Rate Amount

Supply, Installation, Testing and Commissioning of 80 ltrs Seamless

Cylinder with Valve with all accessories( Pressure Guage +Low

pressure supervisory switch,Low Pressure Connection Tee Cable,

Pneumatic actuator, Manual Actuator, Flexible Discharge Hose, Tee,

Check Valve, Flexible Actuation Hose, Pressure Switch for gas release

input, Low Pressure Connection Unit, Connection kit for End of Line,

Elbow), Sinorix FK5112 gas, Electromagnetic Actuator, Discharge

A Nozzles Drilled for 360 degree covereage, M.S. Seamless pipes as per

ASTM A 106 Gr. B, schedule 40 with necessary fittings, Manifold for

Cylinders , Cylinder MOUNTING WLL CLAMP, DNE (Don’t Enter Gas

released) Sign board, GRE (Gas release Exit) Sign board, Gas

Release Panel, Gas Abbort Switch, Gas Relase Switch, Sounder cum

Digitally signed by SAKET

SCHEDULE OF QUANTITIES: VESDA

S No Description Unit Qty Rate DSR Amount (INR) NDSR Amount (INR)

1 Vesda Laser Focus Panel VLF 250 xtralis Nos. 2 2,52,000 5,04,000.00

2 Power Supply for above panels Nos. 2 42,500 85,000.00

3 Capillary set Nos 6 14,870 89,220.00

5 25 mm dia 2 mm thickness pipings Lot 2 10,000 20,000.00

6 Electronic Hooter Cum Strobe Nos. 2 1,200 2,400.00

Total Basic Amount (INR) 7,58,220.00

Digitally signed by SAKET

SCHEDULE OF QUANTITIES: RODENT & WLD SOLUTIONS

DSR Amount NDSR Amount

S No Description Unit Qty Rate

RODENT SOLUTIONS FOR SERVER ROOM

1 Master Console Panel Capable of connecting to 12 Sattleites complete Nos. 2 28,600.00 57,200.00

2 Satellite Detector units complete as required Nos 18 1,680.00 30,240.00

3 Wire Bundles 2 core complete as required and as per specifications. Set 2 5,000.00 10,000.00

4 Bracket Stand complete as required and as per specifications. Nos. 1 4,500.00 4,500.00

WATER LEAK DETECTION FOR SERVER ROOM

Supply of 4 Zone microprocessor based water leak detection panel with inbuilt Nos

keypad and LED indications of the zones in alarm or fault

2 water leak detection cable Nos 40 2,388.00 95,520.00

3 Electronic hooter Nos 2 1,200.00 2,400.00

Digitally signed by SAKET