SPL REPAIR TO INTERNAL ROADS AT 11GRRC UNDER GE (WEST) LUCKNOW.

M&L for preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc sweeping with broom and and finally fanning the cleaned surface with gunny bags to remove all loose dirt/ dust etc and applying evenly a priming / tack coat with bituminous primer using paving bitumen VG 10 @ 5Kg /10 sqm complete all as directed

M & L for 30 mm thick consolidated thickness bituminous premix semi dense asphaltic concrete with 5.50 % binder content (bitumen of grade VG-30) by weight of total mix, laid by mechanical paver, rolled and compactad to required camber and gradient complete all as specified and as directed.

M&L for premix bitumen macadam laid / rolled and compacted to required gradient and camber (consolidated thickness 75mm or less) by using paving bitumen, any penetration @ by weight of total mix complete all as specified and directed.

Providing & fixing as in repair of "Cat Eyes " of size not more than 130 mm and height not more than 20 mm made out of strong engineering high impact resistant polymer with electronic welded lenses for retro reflective in dry and wet weather conditions along road complete all as specified and directed.

Supply and Fixing in repair Solar road studs having 3 LEDs of colour red/yellow to a side (total 6 Nos) housed in a tough pressure casted aluminium alloy of size 125 x 125mm with built in stem of suitable length for fixing with epoxy. LEDs, solar -cells, 1600MAH battery & light sensor well protected inside under tough unbreakable polycarbonate transparent sheet roof, system workable for 2-3 days (nights) after full charge in 8-10hours complete all as specified and directed.

M & L for providing and laying 2.5 mm thick hot applied thermo plastic road marking paint on roads, pavements and the like exc 10cm wide in uniform thickness with glass beads as per clause no 803 of MORTH specification including cleaning of roads surface, heating the materials with in specified tempreture limits for marking with all necessary arrangements required complete all as specified and directed.

M & L for providing and laying 2.5 mm thick hot applied thermo plastic road marking paint on roads, pavements and the like exc 10cm wide in uniform thickness with glass beads as per clause no 803 of MORTH specification including cleaning of roads surface, heating the materials with in specified tempreture limits for marking with all necessary arrangements required complete all as specified and directed.

Demolition of brickwork built in cement mortar or cement lime mortar complete all as specified and directed

M&L for old size brick work with fly ash brick straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L for brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick wall in CM 1:4 complete all as specified and directed.

M & L for rendering 15mm thick in CM 1:4 on fair faces of brickwork or concrete surface and finishing the surface even and fair complete all as specified and directed.

M & L for preparation of new srfaces of wall and applying three coats of white wash complete all as specified and directed.

M/L for PCC 1:2:4 Type B-1 (using 20 mm graded stone aggt) as in benching and coping etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15cm thick (below or above ground level) complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including necessary excavation making drainage opening wherever required complete.

Preparation of old/new surface of concrete/kerb stone surfaces, facias, cornices etc by removing all scale, loose material dust etc and applying two coats of weather proof anti fungal (Apex) paint over one coat of Birla/JK wall care putty to achieve surface smooth and applied as per manufacturers instruction complete specified and directed.

Material and Lobour for metal road delinators made out of 75mm bore medium grade MS pipe of length 80cm embeded with PCC 1:3:6 of size 30cm x30cm x 30cm using 20mm graded stone aggregate 30cm below road level including taking down existing corroded/broken delinators and applying tow coats of synthetic enamel paint over a coat of zinc chrome paint and fixing with high intensity prismatic reflective tapes of 137.5mm width red colour in 2 pieces and 137.5mm yellow/white colour 1 piece alternatively all as specified and directed by GE.

S & F in repair Bench side made of cast iron material. FRP strips shall be used in between cast iron legs. Length 5ft, width 3ft, height 2.5ft above the ground, whole bench shall be tightened on nut & bolts and cast iron legs shall be painted with Asian Paints enamel glossy complete all as specified and directed by Engineer in Charge.

M & L for kerbstone having dimensions of 0.3m in length 0.10m in width and 0.30 in height constructed from high strength concrete M-35 and it incorporate 6mm thick 40 grade acrylic sheets in milky white for illumination, emitting a red blinking light at 4000k and powered by IP68 LED technology, the kerbstones operate on solar energy providing a brightness fo 60 lumens Solar panels will be attached individually to each kerbstone Installation involves a pre prepared PCC bed. The kerbstones comply with IS Code 5758 and IRC standards for road signage. Additional features include customizable color-changing LED's. Quality assurance includes water and impact testing, while cleanliness and wiring integrity.

M & L for 75mm thick Ready Mix concrete using M-25 Grade concrete with OPC Cement and fly ash, ISI marked polypropylene fibers and admixtures as per ACI 310R -13 and IS 9103: 1999. The mix will include ASTM compliant shrinkage-control fibers, IS 383:2016 aggregates,and a water cement ration< 0.45. Concrete must come from QCI approved plants or suppliers with > 500 Cum of stamp concrete, UV resistant, abrasion-resistant color hardeners (IS 1237:2012,ASTM C 979) will be applied at 3.0 - 4.0 Kg/Sqm and sealed with ASTM C1315-compliant sealers to protect against UV, moisture and chemicals while enhancing surface appearance and slip resistance. work includes for laying over a compacted PCC/GSB base with a 90 GSM LDPE sheet, applying hardeners and release agents, stamping with PU/rubber mats, and sealing, control joints (1/3rd depth) will be cut within 48 hours and align with patterns. Isolation joints will be provided as needed complete all as specified and directed.