SPECIAL REPAIR TO BLDG. NO. P-72 IN B WING AT 213 TRANSIT CAMP, PROVN OF ONE TOILET/BATHROOM AND 5000 LTRS OH WATER TANK AT ASCON NODE C-HILL AND 02 X INCINERATOR POINT BEHIND CAMP AT NAGROTA UNDER GE NAGROTA

Amount

Dismantling brick tiles or terracing tiles Single Layer on roof including cleaning the roof surface and filling the cracks (if observed) with silicon compound, complete all as specified and directed.

M & L for PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in padding finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and as directed.

M&L for Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including bitumen primer @ 3.5 Kg/Sqm, complete all as specified and directed.

M&L for APP (atatic polypropline) modified membrane 3mm thick minimum weight not less than 3kg/sqm with 160 gsm/Sqm, non wove polyster mat as center core reinforced laid with 75mm side overlap and 100mm end overlap. The membrane has to be laid with LPG torch and over lap shield and finished neat over roof including a coat of bitumen 85/25 @ 1.2 Kg/Sqm over APP membrane, complete all as specified and directed.

M&L for Cement concrete tiles 25cm x 25cm x 20mm thick, machine pressed, set jointed and pointed in neat cement slurry and roof over APP membrance laid over 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Taking down chowkat with shutter (without taking off shutter from the frame) not exceeding 1.5 sqm each and removing from site (wood or steel), complete all as specified and as directed at site.

Taking down chowkat with shutter (without taking off shutter from the frame) exceeding 1.5 sqm but not exceeding 4 Sqm each and refixing in the same opening, complete all as specified and as directed at site.

S & F factory made solid PVC door frame of size 50mm x 47mm ,made out of 5mm plain colour PVC sheet reinforced with MS square tube as per specification and drawing, complete all as specified and directed.

S & F 30 mm thick (style) Factory made solid panel PVC door shutter consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

S & F 150 mm aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

S & F 75 mm long butt hinges, medium wight cold rolled mild steel, complete all as specified and directed.

S & F 150 mm aluminium handles cast type anodized, complete all as specified and directed.

S&F second class hardwood , plain, solid , straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints, complete all as specified and directed

S & F 35 mm thick second class hard wood, factory made, plain, framed, panelled shutters (two numbers of panels) with lock rail and panel of 9 mm BWP commercials ply or 12 mm veneered particle board on both faces. The size of rails and size as per IS:1003 (Part-I), Kiln seasoned & chemically pressure treated, complete all as specified and directed.

S & F 35 mm thick second class hard wood, factory made, glazed and skelton shutters, open rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamered or rounded, fitted with cut and mitred beads for securing glass, etc. Size of memebers of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) for doors, complete all as specified and directed.

S & F 100 mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

Mild steel sliding door bolts,bolt type 250 mm long stove enamelled black with bright bolt not less than 12mm dia with & incl a minimum of 6 bolts & nuts four on bolt plate and two on staple plate complete all as spd & directed.

S & F 125 mm Mild steel pressed handle oval type stove enameled black, complete all as specified and directed.

S&F for mild steel works as in hold fast and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

M&L for PCC 1:3:6 type C-1(using 20mm graded broken stone aggregate) for fixing hold fast complete all as specified and directed

Prepration of wood or wooden based new or previously untreated surface of any description, over 10 cm width or gridth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Box type steel window side hung double shutters with provision for desert coller/AC (Inside for wire mesh & outside for glass), including guard bar hinges, steel handle, tower bolt and steel peg stay complete with glazaing bar dovetailed for welded and fixed steel window shall be conforming to relevant IS complete all as shown on drawing No CEUZ/TD/1302/09, Sh 1/3 to 3/3 including taking down of existing steel windows, complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured and paid separately.

Box type Steel ventilators top hung double shutters (inside for wire mesh & out side for glass), including hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing.Steel window shall be conforming to relevant IS, complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured and paid separteley.

S & F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm dia and fixed with tinned tacks or galvanised mild steel staples, complete all as specified and directed.

S & F 3.00 mm thick Sheet glass ordinary quality and glazing with oil putty and pin(steel spring for fixing glass) in square n exc 0.5 Sqm in each pane, complete all as specified and directed.

S & F 3.00 mm thick Sheet glass ordinary quality and glazing with oil putty and pin(steel spring for fixing glass) in square n exc 0.5 Sqm in each pane including hacking out old glass panes, complete all as specified and directed.

Prepration of new steel surfaces any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Demolition of brick work / stone masonry built in cement mortar or cement lime mortar including all quoins ,arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6, complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 10 mm thick on fair faces of concrete surfaces in CM 1:3 on ceiling finished even and smooth without using extra cement, complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of 3mm thick wall putty and one coat of primer, complete all as specified and directed.

Preparation of old plastered surfaces of wall and applying two coat of oil bound distemper over a coat of 3mm thick wall putty complete all as specified and directed.

Preparation of new plastered surfaces of wall and applying two coats cement base paint over a coat of primer, complete all as specified and directed.

Preparation of old plastered surfaces of wall and applying two coats cement base paint over a coat of primer, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M & L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in coping and fixing of swan angle etc, complete all as specified and directed.

Preparation of surfaces incl brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts over all decorated plastered or un plastered surfaces of ceiling incl cornices etc and applying one coat of white wash upto four storie build complete all as specified and directed by Engineer-in-charge.

M & L for preparation of new plastered surfaces of ceilings and applying three coats of white wash, complete all as specified and directed.

Surface excavation not exceeding 30 cm and averaging 15cm deep in any type of soil, complete all as specified and directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out any type of soil, complete all as specified and directed.

M & L for PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base on floors, foundation filling and mass concreate, complete all as specified and directed.

Mild steel Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165, complete all as specified and directed.

Removing surplus soil to a distance not exceeding 50m and deposited where directed at a level not exceeding 1.50m from the starting point., all as specified .

Returning filling including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick in any type of soil, complete all as specified and directed.

M&L for hard core of broken stone or boulders n exe 63 mm, deposited, spread and levelled in layers n exe 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M & L for 100 thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in floors, foothpath, plinth protection finishes , complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type B-2 (using 40 mm graded crushed stone aggregate) as in sub base floor finished concrete surface even and smooth, complete all as spd and directed

M & L for chequered cement concrete tiles 25 mm thick set, joined and pointed in neat cement slurry in floors with grey cement and no pigment over and including 20 mm thick screed bed or bedding layer in CM 1:4, and 25 mm thick PCC 1:2:4 type B-1 (using 40 mm graded crushed stone aggregate), complete all as specified and directed.

Formwork to sides of concrete foundations, bases for column beams, plinth beams and soffits of foundation and pllinth beams and similar work (rough finished), complete all as specified and directed.

S&F mild Steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including crancking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90 MM dia or securing with clips quality conforming to Gd I, IS 432(part I) or Fe-410-S or Fe-410-0, complete all as specified and directed.

All as per ser item No. 54 here in above but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and venders

M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 with using WPC (WPC to be measured and paid separately) finished even and smooth without using extra cement, complete all as specified and directed.

S&F 0.63mm thick mild steel. Plain , galvanised irom sheet in hearths, chullah hoods, etc cut to size, edges beaded if directed, holes punched, including round headed screws clout noiols or rivets and fixed to wood or steel members etc with plain 40mm lap joints or welded/riveted seams including bending turining up, mitred angles, stopped ends, outlets etc as required complete all as specified and directed

M & L for RCC 1:2:4 type B-0, (using 12.5 mm graded crushed stone aggregates) as in walls, retaining walls, basement walls, ballast walls and the like any thickness above top of footings including attached pillasters and buttresses, complete all as specified and directed.

Supply only liquid water proofing compound, complete all as specified and directed.

M&L for RCC 1:2:4 type B-0 ( 12.5 mm graded aggregate) slab supported on wall, beams and column in floor, roofs, landing, balconies, canopies, deck slabs and in shelves complete all as specified and directed

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base floor finished concrete surface even and smooth, complete all as spd and directed

M&L for hard core of broken bricks n exe 63 mm , deposited, spread and levelled in layers n exe 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M & L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in surface channel and drain, complete all as specified and directed.

M&L or extra forming fair finished drain or channel 15 cm inner girth in cement concrete using extra cement including form moulds mitred/stopped end etc complete all as specifed directed

S&F of framed work as in door (as in chowkats) or gates of angle or other section with guest plates rails, braces rail etc exclusive of steel sheeting or other covering hanging also fastening and fixing comforming to Fe-410-0 or Fe-310-0 including shop coat of red oxide including preparation of surface before fixing, complete all as specified and directed.

S&F 15mm bore Bib taps, cast copper alloy with crutch or butterfly handle,screwed down,screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed by Engr-in-Charge.

S&F 20mm bore stop valves, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle.screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed by Engr-in-Charge.

S & F 20mm bore steel water tubing 'medium grade' galvanised with all fitting (i.e Tee, socket, bend etc) and fixed complete to walls and ceiling or laid in floors, complete all as specified and directed by Engr-in-Charge.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:4, complete all as specified and directed.

S & F 15mm bore steel water tubing 'medium grade' galvanised with all fitting (i.e Tee, socket, bend etc) and fixed complete to walls and ceiling or laid in floors, complete all as specified and directed by Engr-in-Charge.

M&L for reinforced cement concrete 1:2:4 type B-1 (20 mm graded aggregate) for foundation including rafts, footings foundation ,beams, linth beams etc complete all as specified and directed

M&L for reinforced cement concrete 1:2:4 type B-1 (20 mm graded aggregate) for beams, linth over 1.5m span complete all as specified and directed

Use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs landing and similar work not exc 200 mm thick fair finished surfaces of concrete complete all as specified and directed

S&F mild Steel TMT bars 08 mm dia and over, cut to length, bent to shape required, including crancking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90 MM dia or securing with clips quality conforming to Gd I, IS 432(part I) or Fe-410-S or Fe-410-0, complete all as specified and directed.

Use and waste form work for sides of columns complete all as specified and directed

Use and waste form work for sides for sides foundations etc for rough finished surfaces complete all as specified and directed

Use and waste of formwork to sides and soffits of floor or roof beams, beams hasuchings firder, bressum mers, lintels, cantilivers, shelves incl supports, overhangs etc. also splay between floors and beams etc for rough finished surfaces complete all as specified and directed

M & L for preparation of new plastered surfaces of walls and applying three coats of white wash, complete all as specified and directed.

M&L for reinforced cemnet concret 1:2:4 type B-1 (20mm graded aggregate) for column complete all as specified and directed

M & L for Non-skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but n exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or beddding layer of CM 1:6, complete all as specified and directed.

M & L for Glazed ceramic coloured printed tiles (first quality) of size 450 mm x 350 mm x 7 mm thick as in vertical surface, dado/skirting, set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendering in CM 1:4 for laying of tiles in vertical surfaces, complete all as specified and directed., complete all as specified and directed.

S&F 75 mm bore PVC (SWR) soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches etc including necessary excavation & earth work whenever, complete all as specified and directed.

All as per ser item No.82.00 here in above but 110 mm

S&F PVC (SWR) Bends any radius for 110mm bore.

PVC (SWR) Bends any radius for 75 mm bore.

Cutting into existing manholes for connectiong news drains , making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section ) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as requried for 110mm bore pipe as directed

S&F 15mm bore stop valves, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle.screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed by Engr-in-Charge.

S&F PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed

S&F 20 mm bore ball brass valve fancy.high pressure with polythene float and flynut complete scewed for iron pipe or brass ferrule complete all as specified.

Rotational moulded polyethylene (three layer) water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position of capacity 500 litres including dismantling existing water tank and making inlet out let washout connection with fittings fixed complete all as specified and directed.

S&F vitreous china squatting pan ORRISA pattern, size 580x440mm white, with integral foot rest including provn of concrete bedding and connection to trap and flushing pipe antisyphonage pipe etc including making good to floor, complete all as specified and directed.

S & F 10 Ltrs capacity PVC valveles, less symphonic action type, flushing cistern low level, white with inlet, ball valve, float and handle including bracket and 32 mm bore flush pipe, complete all as specified and directed.

S&F PVC(SWR) 100mm dia floor trap, plain with grating including jointing with solvent cement complete all as specified and directed

S&F white vitreous china counter wash hand basin of size 410x910x150mm fixed in granite counter by making suitable size hole, new brackets, 32mm dia brass chromium plated waste coupling, CP botle trap complete all as specified and directed

S&F 15mm bore pillar taps, cast copper alloy(fancy type) chromium plated,screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore angular cock, cast copper alloy(fancy type) chromium plated,screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed by Engr-in-Charge.

M&L for point wiring with PVC insulated unsheathed 1100 V grade FR cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2 mm thick covered with 3 mm thick plastic laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5 sqmm FR multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly complete all as specified for the following;-

One light point controlled by one switch 5 Amp.

S&F switch piano flush type 5 Amps single pole one way, complete all as specified and directed by Engr-in-Charge.

S&F of ceiling rose surface type 65mm x 50mm 2 to 3 terminal, complete all as specified and directed by Engr-in-Charge.

S & F Integrel sleek extruded batten aluminium /CRCA channel fitting with LED 18 watt complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, , complete all as specified and directed.

S&F lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S & F LED bulb 7 watt complete all as specified and directed.

S&F sheet metal enclosure distribution board SPN 2 way 230 V, 50 Hz single door with neutral, Earthing bar and din rail complete all as specified and directed.

S & F MCB SPN 40 Amps, 10 KA, 230 volts 'C' series, complete all as specified and directed.

Supply and laying or fixing including removing of existing cable 1100 volts grade cable PVC insulated aluminium conductor un-armoured of 6 Sqmm 2 core flat or circular, served with inner sheathing of pace tape and overall PVC sheathed in service connection suspended by insulated hangers not more than one Mtr apart including 4 mm dia suspension GI wire, complete all as specified and as directed by Engr-in-Charge.

Deduction to be made from BOQ for schedule of credit (Sch 'A' Part - II) Amount of Rs. 13,800.00 during AOC Note:- Tenderers shall not quote for this Schedule

BHARTI CONSTRUCTIONS

Kalsi Engineers and contractors

BMMJ TRADERS AND ENGINEERS

CHOPRA CONSTRUCTIONS