Loading
Loading…
Loading…
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹72.8 L
EMD Value
₹1.5 L
Closing Date
28 Oct 2026, 3:00 pm
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
TENDER ELG
15 conditions · 3 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less where V= Advertised value of the tender in crores of Rupees, N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.(In this connection scanned copy of Annexure VIB duly filled up must be attached with offer).
The tenderer must have successfully completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works costing not less than the amount equal to 40% of advertised value of the tender, or One similar work costing not less than the amount equal to 60% of advertised value of the tender .Other terms and conditions shall follow of GCC, April 2022. Definition of Similar nature of work has given below (1.1)
Defination of Similar Work :- As per CEE's letter No. EL/112/0, dated 16.09. 2025 : Item Sl. No. 1.(iii) under "HT Electrical Works" : Supply, Installation, Testing and Commissioning of HT Sub-Station of same KV or higher KV including associated Electrical work with / without AMC OR Replacement / Maintenance / Modification / Upgradation / Augmentation of same KV or higher KV Sub-Station related work with / without HT Panel .AND Item Sl. No.2.(ii) under "LT Electrical Works" : Execution of any HT or LT Electrical work.
Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
14 conditions · 4 needing a document upload
The details of the uploaded documents should be produced whenever demanded for verification on written request at any point of time of the tender and contract within 7 days.
Scanned copy of valid GST (Goods & Service Tax)Registration Certificate.
The following documents should be attached with the tender ( Annexure-V (A) certificate is to be given by attorney/authorized signatory/each member of Partnership firm/Joint Venture (JV) / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. & Scanned copy POA/Partnership deed is to be uploaded Duly filled up by the bidder
Partnership deeds, power of Attorney etc. (if any) : The tender shall clearly specify whether the tender is submitted on his own or on behalf of a partnership concern. If the tender is submitted on behalf of partnership concern he should submit the certified copy of the partnership deed along with the tender authorisation to sign the documents on behalf of the partnership firm. If these documents are not enclosed along with the tender document, the tender will be treated as hearing lease submitted by the individual signing the tender documents. The Railway will not consider any power of Attorney granted by the tender or any changes in the composition of the firm made subsequent to the execution of the contract. It may however recognize such power of Attorney and change after obtaining proper legal advice, the cost of which will be chargeable to the contract.(Scanned copy POA/Partnership deed is to be uploaded Duly filled up by the bidder. As per clause no. 14(e) of GCC'22, the following documents to be uploaded in terms of Company registered under Companies Act2013: (i) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate of Incorporation (iii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company. (iv) All other documents in terms Para 10 of the Tender Form (Second Sheet) above.
Option for receiving payment through Letter of Credit . (Please attach scannedcopy of ANNEXURE 1 LC & ANNEXURE 2 LC duly filled up by the firm if optedfor)
The following documents should be attached with the tender: (i)Scanned copy of Pan Card. (ii)Scanned Copy of EFTMANDATE FORM Duly filled up by the bidder(iii)Tender Document (duly digitally signed by the bidder)
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Scanned copy of valid Trade license or Propitorship Certificate.
Railway Officers Associated with tenderer:RAILWAY OFFICERS ASSOCIATED WITH TENDERER 1. ExRailway Officer as tenderer: Should tenderer be a retired Gazetted Officer working before his retirement on any of the Railways owned and administered by the President of India, or should the tenderer being partnership firm have as one of its partners a retired Gazetted Officer as aforesaid, or should the tenderer being an incorporated company have any such retired Officer as one of its Directors, or should the tenderer have in his employment any retired Gazetted Officer as aforesaid, full information of such person shall be submitted along with his tender in the format given in annexure-VI to this chapter of this tender document. (Authority: ACS No.3 to GCC July,2014vide Boards letter No.2014/CEI/CT/O/9/RET dt.22.01.2015)(please attach scanned copy of Annexure-VI duly filled up by the firm).
List of the Works completed in the last three financial years giving description of work. Organization for whom executed, approximate value of contract at the time of award, date of award and date of scheduled completion of work. Date of actual start, actual completion and date of payment and final value of contract should also be given. (Supportive documents/ certificates from the organization with whom worked/are working should be enclosed) (Please attach scanned copy of Annexure-I duly filled up).
List of works in hand indicating Supportive documents/certificates from the organization with whom worked/are working should be enclosed) description of work, contract value, approximate value of balance work yet to be done and date of award. (Supportive documents/certificates form the organization with whom worked/are working should be enclosed).(Please attach scanned copy of Annexure-IV duly filled up)
Submission of Documents in support of Eligibility Criteria : All documents in support of fulfillment of eligibility criteria with respect to completion of 'Similar Nature of work for technical Eligibility criteria 'and 'Total Contract value for Financial Eligibility Criteria' should be uploaded online in the website with scanned copy at the time of tender bidding with the details. No post - tender communication , in any form will be made or entertained , after opening of tenders in this regard .Railways may however call for the originals of the credentials for verification or any clarifications/Confirmations on the contents of the documents submitted .Eligibility of tenderers shall be decided solely on the basis of the documents submitted alongwith the tender offers and any subsequent document whatsoever submitted in this connection would not be given any cognizance on any account.
The Contractor/(firm) must go through the entire tender document along with all attachment for any kind of guidance regarding execution of the job & payment there after. In case any thing is left out or not clear then they should consult the General Condition of Contract & standard Specification as attached (uploaded ).The bidders are also advised to preserve a copy of entire tender document/ (Set) for their convenience.
Electrical (General) work in connection with Construction of retiring room along with other ancillary works at TAK station under the jurisdiction of AEN/LLH
EL-HWH-25-21-3664~ER
EL-HWH-25-21-3664
Open
Works - General
180 Days
Howrah, West Bengal
₹0
₹1.5 L
5 Oct 2026
5 Oct 2026
14 Oct 2026
156 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 72,76,463 | ||
| — | — | — | Above/ 24000.00 Below/P | ||
| Drawing of cable on wall / structure with suitable sizeand shape GI clamps including supply of suitable size GI Clampand GI nut-bolts and commissioning of cable( Cable will be supplied by Railway ) | — | 600.00 | — | — | |
| — | — | — | Above/ 187200.00 Below/P | ||
| Trenching and laying of cable underground by pucca floor / concrete cutting with covering of cable through suitabe dia HDPE pipe including supply of HDPE pipe (PE-100 grade, PN-10 orhigher) along with refilling the trench and make good of surface as its original condition( Cable will be supplied by Railway ) | — | 800.00 | — | — | |
| — | — | — | Above/ 182400.00 Below/P | ||
| Trenching and laying of cable under ground by soil cutting through suitable dia HDPE pipe including supply of HDPE pipe(PE-100 grade, PN-10 or higher) alongwith refiling of trench by excavated soil and make good of surface as its original condition. ( Cable will be supplied by Railway ) | — | 1200.00 | — | — | |
| — | — | — | Above/ 17850.00 Below/P | ||
| Trenching and laying of cable underground by pucca floor / concrete cutting and commissioning of cable alongwith make good of floor surface as its original condition after laying of cable( Cable will be supplied by Railway ) | — | 210.00 | — | — | |
| — | — | — | Above/ 84360.00 Below/P | ||
| Trenching and laying of cable underground by pucca floor / concrete cutting and commissioning of cable through 80mm dia GI pipe including supply of GI pipe alongwith make goodof floor surface as its original condition after laying of cable( Cable will be supplied by Railway ) | — | 120.00 | — | — | |
| — | — | — | Above/ 66500.00 Below/P | ||
| Trenching, laying under road / track through 100 mm dia GIpipe ( medium gauge ) including supply of GI pipe and commi-ssioning of cable including back filling of trench with excavatedsoil after laying of cable ( Cable will be supplied by Railway ) | — | 140.00 | — | — | |
| — | — | — | Above/ 150000.00 Below/P | ||
| Laying of cable underground through 100 mm diameterHDPE pipe by Micro Tunneling cable laying method including supply and jointing of HDPE pipe (PE-100 grade, PN-10 or higher). ( Cable will be supplied by Railway ) | — | 100.00 | — | — | |
| — | — | — | Above/ 8650.00 Below/P | ||
| Drawing of cable through one no. 2" dia, 3.0 Mtrs. longGI pipe ( Make - Tata / Jindal / Bansal ) for protectionof cable on pole with proper GI clamps and GI nuts & boltsincluding supply of GI pipe( Cable will be supplied by Railway ) | — | 10.00 | — | — | |
| — | — | — | Above/ 16122.00 Below/P | ||
| Supply of Straight Through jointing kits ( Heat shrinkable )suitable for XLPE / PVC insulated stranded Aluminium conductor cable of size 4 / 3.5 x 50-95 sq.mm., 1100V grade complete with all accessories including jointing, testing and commissioning.( Make - m-seal / Raychem / Mahindra / Densons / 3M / Polycab ) | — | 6.00 | — | — | |
| — | — | — | Above/ 24124.00 Below/P | ||
| Supply of Straight Through jointing kits ( Heat shrinkable )suitable for XLPE / PVC insulated stranded Aluminium conductor cable of size 3 x 70 / 95 / 120 sq.mm., 11 KV grade complete with all accessories including jointing, testing and commissioning.( Make - m-seal / Raychem / Mahindra / Densons / 3M / Polycab ) | — | 2.00 | — | — | |
| — | — | — | Above/ 20980.00 Below/P | ||
| Supply of Indoor End Termination jointing kits ( Heat shrinkable )suitable for XLPE / PVC insulated stranded Aluminium conductor cable of size 3 x 120-150 sq.mm., 11 KV grade complete with all accessories including jointing, testing and commissioning.( Make - m-seal / Raychem / Mahindra / Densons / 3M / Polycab ) | — | 2.00 | — | — | |
| — | — | — | Above/ 1800000.00 Below/P | ||
| Supply of Dry Type Resin casted 500 KVA capacity, 11KV / 415V, 50 Hz, Outdoor type Transformer, Vector Group :- Dyn11 ( 11 KV Delta connection, 415V Star connection ), Insulation Class - H, copper winding, Air natural cooling with off load tap changing links and as per reference standard IS 2026-11 & IEC 60076-11 complete with powder coated MS sheet encloser with fully covered HV & LV Cable terminal box.( Make - Hitachi ABB / Siemens / Voltamp Transformers Ltd. / Kirloskar Electric Company Ltd. / BHEL )( Please see 'Detailed technical specification' ) | — | 1.00 | — | — | |
| — | — | — | Above/ 90000.00 Below/P | ||
| Installation, connection, testing and commissioning of above500 KVA dry type transformers including plinth constructionalong with construction of iron shed structure with transparent sheet top cover and MS grill structure duly painted at four sides of transformer including dismantling of existing 200 KVA transformer and shifting from Tarakeswar Sub Station to BandelSub- station including transportation, loading and unloading work. | — | 1.00 | — | — | |
| — | — | — | Above/ 131400.00 Below/P | ||
| Wiring of Light / Fan / Call Bell / Glow Sign point by 2 nos.single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 1.5 sq.mm, 1100V grade for phaseand neutral in PVC conduit / casing along with 1 no. singlecore HRFR / FRLS grade, PVC insulated, copper conductorcable of size 1.5 sq.mm, 1100V grade for Earth ContinuityConductor ( ECC )( Make of Copper conductor cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 450.00 | — | — | |
| — | — | — | Above/ 11410.00 Below/P | ||
| Wiring of 6A / 3 pin Plug board consisting with one plug socketand one 6A switch by 2 nos. single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 1.5 sq.mm, 1100V grade for phase and neutral in PVC conduit / casing along with 1 no. single core HRFR / FRLS grade, PVC insulated,copper conductor cable of size 1.5 sq.mm, 1100V grade for Earth Continuity Conductor ( ECC )( Make of Copper conductor cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 70.00 | — | — | |
| — | — | — | Above/ 11550.00 Below/P | ||
| Wiring of 6/16A 3 pin Plug board consisting with one 16/6A 3 pin plug socket and one 16A switch by 2 nos. single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 2.5 sq.mm, 1100V grade for phase and neutral in PVC conduit / casingalong with 1 no. single core HRFR / FRLS grade, PVC insulated,copper conductor cable of size 1.5 sq.mm, 1100V grade forEarth Continuity Conductor ( ECC )( Make of Copper conductor cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 30.00 | — | — | |
| — | — | — | Above/ 14200.00 Below/P | ||
| Wiring of Multi Plug board consisting with three nos. 6A / 5 pin plug socket, three nos. 6A switch, one no. 16A / 6 pin plug socket, one no. 16A switch, one no. 10A fuse kit-kat / MCB and one indicator ( Red ) by 2 nos. single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 4 sq.mm, 1100V grade for phase and neutral in PVC conduit / casing along with 1 no. single core HRFR / FRLS grade, PVC insulated,copper conductor cable of size 2.5 sq.mm, 1100V grade for Earth Continuity Conductor ( ECC )( Make of Copper conductor cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 25.00 | — | — | |
| — | — | — | Above/ 13788.00 Below/P | ||
| Wiring of AC Machine ( Window / Split ) / Water Cooler point by2 nos. single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 4 sq.mm, 1100V grade for phase and neutral in PVC conduit / casing along with 1 no. single core, HRFR / FRLS grade, PVC insulated, copper conductor cable ofsize 2.5 sq.mm, 1100V grade for Earth Continuity Conductor ( ECC ) and each switch board comprising with one power unit which includes one double pole MCB, one single phase starter and one 6/16A 3 pin socket and plug with indicating light andall other associated work( Make of Copper conductor cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 12.00 | — | — | |
| — | — | — | Above/ 108800.00 Below/P | ||
| Wiring of Submain by 2 nos. single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 4.0 sq.mm, 1100V grade for phase and neutral in PVC conduit / casing along with 1 no. single core HRFR / FRLS grade, PVC insulated,copper conductor cable of size 2.5 sq.mm, 1100V grade for Earth Continuity Conductor ( ECC )( Make of Copper conductor cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 1600.00 | — | — | |
| — | — | — | Above/ 99200.00 Below/P | ||
| Wiring of Mainline by 2 nos. single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 6.0 sq.mm, 1100V grade for phase and neutral in PVC conduit / casing along with 1 no. single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 4.0 sq.mm, 1100V grade for Earth Continuity Conductor ( ECC )( Make of Copper conductor cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 800.00 | — | — | |
| — | — | — | Above/ 69600.00 Below/P | ||
| Wiring of Mainline by 2 nos. single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 10 sq.mm, 1100V grade for phase and neutral in PVC conduit / casing along with 1 no. single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 4.0 sq.mm, 1100V grade for Earth Continuity Conductor ( ECC )( Make of Copper conductor cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 300.00 | — | — | |
| — | — | — | Above/ 35685.00 Below/P | ||
| Extra cost for conceal wiring in respect to PVC conduit / casingfor light, fan, plug, power plug, multi-plug point etc. includingmake good of wall surface as its original condition | — | 585.00 | — | — | |
| — | — | — | Above/ 51300.00 Below/P | ||
| Extra cost for conceal wiring for main / submain with respect to PVC conduit / casing including make good of wall surface as its original condition | — | 2700.00 | — | — | |
| — | — | — | Above/ 73500.00 Below/P | ||
| Extra cost involvement for modular switch, bell push, plug socket, fan regulator, USB point, TV socket etc.with other accessories( Make of Modular switch, socket, box, cover plate etc. - Anchor ( Panasonic ) / Havells ( Crabtree ) / Legrand / LK (L&T) ) | — | 750.00 | — | — | |
| — | — | — | Above/ 14000.00 Below/P | ||
| Supply of Wall / Pillar mounted Sheet Moulding Compound( SMC ) Mobile Charging Plate for holding mobile set of width 125 mm ( 5 inch ) duly painted including fitment with suitable attachment as per site condition | — | 1000.00 | — | — | |
| — | — | — | Above/ 106000.00 Below/P | ||
| Designing of mounting layout, supply, installation, connection and commissioning of 20-22W LED batten (Type of LED - Surface Mounting Device ) tube with industrial grade constant current Driver ( Efficiency - Greater than 85% ) with short circuit protection, extruded aluminium housing and milky polycarbonate diffuser ( LEDchip make - Nichia, Osram, Seoul, Philips, Lumileds, Everlight, Avago,Cree, Lednium, APT Electronics & BridgeLux ), LED luminaire system efficacy - Greater than 120 Lumens per Watt @ 350mA drive current,Colour Temperature - 6500K (Cool white), CRI>80, SDCM<5, Driver Operating Voltage - 140-270 Volt AC, Surge Protection minimum 4KV, THD<10%, Driver HV Cut off @ 325V/440V (P2P) protection for8 hrs., Life span of LED chip Greater than 50000 burning hours, The Luminaire & Driver both should be of same make / brand and indivi- dually BIS approved with 60 months warranty including fixing withGI clamps made of GI flat of suitable size & GI nut-bolts.( Make : Philips (Signify) / Havells / Bajaj / Panasonic / Crompton / Jaquar / Lighting Technologies / Halonix ) | — | 500.00 | — | — | |
| — | — | — | Above/ 14000.00 Below/P | ||
| Designing of mounting layout, supply, installation, connection and commissioning of Recess mounted 15W (approx.) LED Circular typeluminaire (Type of LED - Surface Mounting Device ) fittings with soft glare free symmetrical illumination (for mounting in false ceiling), Driver Efficiency - Greater than 85% with short circuit protection, withpolycarbonate (UV stabilized) diffuser, ( LED chip make - Nichia, Osram, Seoul, Philips, Lumileds, Everlight, Avago, Cree, Lednium,APT Electronics & BridgeLux )( LED chip as per LM 80/IS16106 ), LED luminaire efficacy - Greater than equal to 120 Lumens per Watt@ 350mA drive current, Colour Temperature range - 3000K, CRI>80,SDCM<5, operating Voltage and frequency range - 140-280 Volt ACat 50 Hz, Surge Protection minimum 4KV, High voltage withstand capacity upto 1.5 KV for one min. THD<10%, Driver HV Cut off @ 325V/440V (P2P) protection for 8 hrs., Life span of LED chip Greater than 50000 burning hours as per LM-80 report and shall comply with compulsory registration (CRS) of BIS for safety as per IS 10322 (Part 5/Section 2) 2012. The Luminaire & Driver both shouldbe of same make/brand and individually BIS approved with 60 monthswarranty including fixing with GI clamps made of GI flat of suitable size & GI nut-bolts.( Make : Philips (Signify) / Havells / Bajaj / Panasonic / Crompton / Jaquar / Lighting Technologies / Halonix ) | — | 25.00 | — | — | |
| — | — | — | Above/ 87430.00 Below/P | ||
| Designing of mounting layout, supply, installation, connection and commissioning of Recess mounted 36W (approx.) LED Flat Panel luminaire (Type of LED - Surface Mounting Device ) fittings with soft glare free symmetrical illumination of size 2 Ft x 2 Ft shape, Driver Efficiency - Greater than 85% with short circuit protection, withpolycarbonate (UV stabilized) diffuser, ( LED chip make - Nichia, Osram, Seoul, Philips, Lumileds, Everlight, Avago, Cree, Lednium,APT Electronics & BridgeLux ), LED chip efficacy - Greater than equal to 130 Lumens per Watt @ 350mA drive current, ColourTemperature range - 5700K-6000K, CRI>80, SDCM<5, operating Voltage and frequency range - 140-280 Volt AC at 50 Hz, Surge Protection minimum 4KV, High voltage withstand capacity upto 1.5 KV for one min. THD<10%, Driver HV Cut off @ 325V/440V (P2P) protection for 8 hrs., Life span of LED chip Greater than 50000 burning hours as per LM-80 report and shall comply with compulsory registration (CRS) of BIS for safety as per IS 10322(Part 5/Section 2) 2012. The Luminaire & Driver both should be of same make / brand and individually BIS approved with 60 monthswarranty including fixing with GI clamps made of GI flat of suitable size & GI nut-bolts.( Make : Philips (Signify) / Havells / Bajaj / Panasonic / Crompton / Jaquar / Lighting Technologies / Halonix ) | — | 70.00 | — | — | |
| — | — | — | Above/ 2814.00 Below/P | ||
| Supply of LED 3W step / foot light integrated with high efficient LEDswith die-cast aluminium housing and clear glass (Colour temperature3000K/4000K/6000K) complete with all accessories, operating Voltage and frequency 230V AC, 50Hz ( similar to Legero Model No.- EDGE LSA 3003 or equivalent ). | — | 6.00 | — | — | |
| — | — | — | Above/ 444.00 Below/P | ||
| Fixing, connection, testing and commissioning of indoor LEDluminaire fittings with suitable arrangement. | — | 6.00 | — | — | |
| — | — | — | Above/ 12800.00 Below/P | ||
| Supply of Outdoor type Warm White LED Rope light 9W per metrewith all accessories. | — | 100.00 | — | — | |
| — | — | — | Above/ 200.00 Below/P | ||
| Fixing, arrangement. | — | 100.00 | — | — | |
| — | — | — | fitting | ||
| — | — | — | with | ||
| — | — | — | suitable | ||
| — | — | — | Above/ 124380.00 Below/P | ||
| Supply of BLDC Ceiling Fan of sweep 1200 mm, Air delivery range from 210 cubic metre per minute to 220 cubic metre perminute and input power consumption range from 26W to 32W ( Star Rating - 5 Star, Service Value - 6 & above cubic metre per minute per watt ) with copper winding and remote for speed control of fan suitable for operation on 1 Ph, 50Hz, 240V power supply system ( conform to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable with BIS certification ) with 60 Months warranty including fixing,connection, testing and commissioning of ceiling fan & regulatorwith suitable clamping arrangement & 'S' hook etc.( Make : Havells / Usha / Orient / Halonix / Atomberg / Crompton / Bajaj ) | — | 60.00 | — | — | |
| — | — | — | Above/ 11160.00 Below/P | ||
| Supply, fixing, testing and commissioning of Modular Exhaust Fan as per IS: 2312 (or latest) Sweep Size-300 mm, White Colour, with Louver Shutter, Plastic Fiber body including fixing with GI clamps made of GI flat of suitable size & GI Nut, Bolts alongwith necessary Masonry works.( Make : Havells / Usha / Orient / Halonix / Atomberg / Crompton / Bajaj ) | — | 6.00 | — | — | |
| — | — | — | Above/ 11228.00 Below/P | ||
| Supply of AC Exhaust Fan 380 mm sweep 4 pole suitable for operation on 1Ph, 220- 250V, 50 Hz supply system without louver Shutter including fixing, connection and commissioning with GI clamps made of GI flat of suitable size & GI Nut-Bolts alongwith necessary masonry works.( Make : Havells / Usha / Orient / Halonix / Atomberg / Crompton / Bajaj ) | — | 4.00 | — | — | |
| — | — | — | Above/ 34740.00 Below/P | ||
| Supply of Bracket type Air Circulator Fan ( metal ) of sweep 600 mm suitable for operation on 1Ph, 230V, 50 Hz supply system includingfixing, connection and commissioning with GI clamps made of GIflat of suitable size and GI Nut-Bolts on wall / structure. ( Make : Havells / Usha / Orient / Halonix / Atomberg / Crompton / Bajaj ) | — | 6.00 | — | — | |
| — | — | — | Above/ 28270.00 Below/P | ||
| Supply of AC Wall Bracket Fan 450 mm sweep suitable for operation on 1Ph, 220- 240V, 50 Hz supply system includingfixing, connection and commissioning with GI clamps madeof GI flat of suitable size and GI Nut-Bolts on wall / structure. ( Make : Havells / Usha / Orient / Halonix / Atomberg / Crompton / Bajaj ) | — | 10.00 | — | — | |
| — | — | — | Above/ 31540.00 Below/P | ||
| Supply, fixing, testing and commissioning of Storage Water Heater 5 star of capacity 25 Ltrs. suitable on 1Ph, 220-250V, 50 Hz supply system including fixing with GI clamps made of GI flat of suitable size & GI Nut, Bolts alongwith necessary Masonry works. ( Make : Bajaj / Venus / Raycold / Havells / Crompton ) | — | 4.00 | — | — | |
| — | — | — | Above/ 852.00 Below/P | ||
| Supply, fixing, connection, testing and commissioning of ElectricBells with all accessories suitable for operation on 1 Ph, 240V,50Hz supply system with suitable arrangement. | — | 4.00 | — | — | |
| — | — | — | Above/ 69060.00 Below/P | ||
| Supply of GI ( minimum coating thickness 65 microns ) conical / octagonal ( minimum sheet thickness - 3mm ) Pole of overall length 5 M with single / double arm bracket, top cover, base plate including hinged door-inbuilt Junction box complete with copper bar, insulator, Hylam sheet for cable termination and fuse kit-kat / MCB ( Make - Utkarsh / B.P. Projects / Crompton / Bajaj / Surya ) | — | 10.00 | — | — | |
| — | — | — | Above/ 31160.00 Below/P | ||
| RCC foundation, erection and commissioning of above GI polewith construction of cement concrete muffing ( Cement : Stone :Sand = 1 : 2 : 4 ) with foundation accessories including earthingof pole with 1 no. of 50 mm dia, 3 M long GI pipe ( Make - TATA / Jindal / Bansal ) with necessary earth connection frompipe to pole by GI Strip / GI wire | — | 10.00 | — | — | |
| — | — | — | Above/ 3580.00 Below/P | ||
| Wiring of light point by 2 nos. single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 1.5 sq.mm, 1100V grade for phase and neutral through pole from inbuilt poleJunction Box's porcelain fuse kit-kat / MCB to light fitting alongwith 1 no. single core HRFR / FRLS grade, PVC insulated copper conductor cable of size 1.5 sq.mm, 1100V grade forEarth Continuity Conductor ( ECC ).( Make of Copper conductor cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 20.00 | — | — | |
| — | — | — | Above/ 71300.00 Below/P | ||
| Wiring of Light / Fan / Call Bell / Glow Sign point by 2 nos.single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 1.5 sq.mm, 1100V grade for phaseand neutral in GI conduit of suitable dia along with 1 no. singlecore HRFR / FRLS grade, PVC insulated, copper conductor cable of size 1.5 sq.mm, 1100V grade for Earth Continuity Conductor ( ECC ).( Make of Copper conductor cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 575.00 | — | — | |
| — | — | — | Above/ 130500.00 Below/P | ||
| Wiring of Light / Fan / Call Bell / Glow Sign point by 2 nos. singlecore HRFR / FRLS grade, PVC insulated, copper conductor cableof size 2.5 sq.mm, 1100V grade for phase and neutral in GIconduit of suitable dia along with 1 no. single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 1.5 sq.mm, 1100V grade for Earth Continuity Conductor ( ECC ).( Make of Copper conductor cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 900.00 | — | — | |
| — | — | — | Above/ 30600.00 Below/P | ||
| Wiring of Light / Fan / Call Bell / Glow Sign point by 4 nos. singlecore HRFR / FRLS grade, PVC insulated, copper conductor cableof size 2.5 sq.mm, 1100V grade for three phases and one neutralin GI conduit of suitable dia along with 1 no. single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 1.5 sq.mm, 1100V grade for Earth Continuity Conductor ( ECC ).( Make of Copper conductor cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 200.00 | — | — | |
| — | — | — | Above/ 30000.00 Below/P | ||
| Wiring of Light / Fan / Call Bell / Glow Sign point by 4 nos. singlecore HRFR / FRLS grade, PVC insulated, copper conductor cableof size 4.0 sq.mm, 1100V grade for three phases and one neutralin GI conduit of 25mm dia along with 1 no. single core HRFR / FRLS grade, PVC insulated, copper conductor cable of size 2.5 sq.mm, 1100V grade for Earth Continuity Conductor ( ECC ).( Make of Copper conductor cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 60.00 | — | — | |
| — | — | — | Above/ 74910.00 Below/P | ||
| Supply of SPN DB ( Metal Enclosure with Metal Door ), 10 way, 1Ph, 240V, 50Hz, complete with 6 nos. SP MCB of current ratingfrom 6A to 32A,10kA, 240V, 50Hz as per requirement of load and 1 no. DP RCBO of current rating 40A, 300mA, 10kA, 230V, 50Hz ( Make of MCB, RCBO and Metal Distribution Board - LK (L&T) / Siemens / ABB / Hager / Legrand / Schneider /C&S / Havells ) | — | 11.00 | — | — | |
| — | — | — | Above/ 1331.00 Below/P | ||
| Fixing, connection and commissioning of above SPN MCB DB with suitable arrangement including all incoming and outgoing cable connection with suitable cable termination arrangement. | — | 11.00 | — | — | |
| — | — | — | Above/ 63592.00 Below/P | ||
| Supply of TPN MCB DB ( Heavy duty, Outdoor type, UV rayprotected, self fire- extinguishing and resistant to abnormal heat and fire up to 650 degree C GWT, shock resistance IK09 or above and IP65 degree of protection grade transparent DB box, similar to ABB Mistral65 - 20 Modulesor equivalent ), 3Ph, 50Hz, 415V, 4 way per phase, 415V, 50Hz, complete with total 12 nos. SP MCB of current rating from 6A to 32A, 10 kA, 240 Volt, 50Hz per phase as per requirement of load and one no. FP RCBO 63A, 300mA, 10 kA, 415V, 50Hz, Suitable for AC + Pulsating DC (Type A) + Harmonics ( Make of MCB & RCBO - LK (L&T) / Siemens / ABB / HagerLegrand / Schneider ) ( Make of TPN DB - LK (L&T) / Siemens / ABB / Hager / Legrand / Schneider / Spelsberg / Hensel / Eaton ) | — | 4.00 | — | — | |
| — | — | — | Above/ 548.00 Below/P | ||
| Fixing, connection, testing and commissioning of above TPNMCB DB including all incoming and outgoing cables glanding, cableconnection with cable termination and suitable wall hanging arrangement as per site condition with all associated accessories. | — | 4.00 | — | — | |
| — | — | — | Above/ 13150.00 Below/P | ||
| Supply of MCB DP, 40A, 1Ph, 240V, 50 Hz, 10kA with polycarbonate distribution box enclosure (IP-65) with polycarbonate transparent openable window including fixing, connection, testing and commissioning.( Make of MCB - LK (L&T) / Siemens / ABB / Hager / Legrand / Schneider / C&S / Havells )( Make of Enclosure - Grasp / OBO Bettermann / ABB / Schneider ) | — | 10.00 | — | — | |
| — | — | — | Above/ 110240.00 Below/P | ||
| Supply of Thermoplastic Polycarbonate Busbar Chamber of dimen-sion 450mm x 300mm x 210mm consisting with 4 nos. tinned copper busbar of each bar of capacity 100 Amp, 4 way, suitable for415V, 50Hz supply system and 4 nos. Cable glands with Ingress protection : IP65 or higher as per IEC-60529 ( weather proof), rust, dust, moisture and shock proof, anti corrosive, halogen freeacid resistant, light weight, impact resistant IK 08/09 as per IEC-60068-2-72, fire returdant, insulated, UV stabilised as per EN ISO4892, should withstand glow wire test at 960 degree C as per IS 11000-2-1,IEC-60695-2-10 and fire rated UL94V-0 complete with hinged door with locking arrangement including fixing, connection and commissioning of above Junction Box on pole/structure withmounting clamp.( Make : Hensel / Sintex / OBO Bettermann / RMC / Grasp / ABB / Legrand / Spelsberg / EPP Composites ) | — | 8.00 | — | — | |
| — | — | — | Above/ 38008.00 Below/P | ||
| Supply, fixing, connection, testing and commissioning of MCCB with Microprocessor Release of breaking capacity 36 kAat 415V, AC 50Hz ( Ics = 100% Icu ) with following features :- 1) Adjustable Over Load, 2) Adjustable Short Circuit, 3) Inbuiltground fault protection, 4) Inbuilt Instantaneous protection5) Adjustable neutral overload protection, 6) Provision of Thermal Memory 7) All Microprocessor protection-based MCCB / ACB must have facility of individual 'LSIG' fault indication,suitable for Release Range 40-100A, 4 Pole including metal enclosure with internal wiring.( Make - LK (L&T) / Siemens / ABB / Hager / Legrand / Schneider / C&S ) | — | 2.00 | — | — | |
| — | — | — | Above/ 19740.00 Below/P | ||
| Designing of mounting layout, supply, installation, connection and commissioning of Flood light 80 Watt LED (Type of LED - Surface Mounting Device ) luminaire, pressure die cast aluminium housing with Ingress Protection - IP66 or higher ( LED chip make - Nichia, Osram, Seoul, Philips, Lumileds, Everlight, Avago, Cree, Lednium, APT Electronics & BridgeLux ), complete with all accessories, LEDluminaire system Efficacy minimum - 130 Lumens per Watt @ 350mA drive current, Impact resistance IK-05 or higher, Colour Temperature - 5700K, Driver Surge Protection minimum 4KV, Life span of LED chip Greater than 50000 burning hours, The Luminaire& Driver both should be of same make / brand and individually BIS approved with 60 months warranty including fixing of outdoor LED Flood light / Street Light fitting on High Mast Tower/Pole/Structurewith suitable arrangement.( Make : Philips (Signify) / Havells / Bajaj / Panasonic / Crompton / Jaquar / Lighting Technologies / Halonix ) | — | 20.00 | — | — | |
| — | — | — | Above/ 6930.00 Below/P | ||
| Designing of mounting layout, supply, installation, connection and commissioning of Street light 90 Watt LED (Type of LED - Surface Mounting Device ) luminaire, pressure die cast housing with IngressProtection - IP66 or higher ( LED chip make - Nichia, Osram, Seoul,Philips, Lumileds, Everlight, Avago, Cree, Lednium, APT Electronics& BridgeLux ), complete with all accessories, LED luminaire system Efficacy minimum - 130 Lumens per Watt @ 350mA drive current,Impact resistance IK-05 or higher, Colour Temperature - 5700K, Driver Surge Protection minimum 4KV, Life span of LED chip Greaterthan 50000 burning hours, The Luminaire & Driver both should be ofsame make / brand and individually BIS approved with 60 months warranty including fixing with suitable dia heavy gauge GI bend pipewith GI clamps made of GI flat of size 40mm x 6mm and GI nut-boltson structure / wall.( Make : Philips (Signify) / Havells / Bajaj / Panasonic / Crompton / Jaquar / Lighting Technologies / Halonix ) | — | 6.00 | — | — | |
| — | — | — | Above/ 22000.00 Below/P | ||
| Designing of mounting layout, supply, installation, connection and commissioning of Street light 90 Watt LED (Type of LED - Surface Mounting Device ) luminaire, pressure die cast housing with IngressProtection - IP66 or higher ( LED chip make - Nichia, Osram, Seoul,Philips, Lumileds, Everlight, Avago, Cree, Lednium, APT Electronics& BridgeLux ), complete with all accessories, LED luminaire system Efficacy minimum - 130 Lumens per Watt @ 350mA drive current,Impact resistance IK-05 or higher, Colour Temperature - 5700K, Driver Surge Protection minimum 4KV, Life span of LED chip Greaterthan 50000 burning hours, The Luminaire & Driver both should be ofsame make / brand and individually BIS approved with 60 months warranty including fixing, connection and commissioning of outdoor Flood light / Street light fitting on High Mast Tower / Pole / Structurewith suitable arrangement.( Make : Philips (Signify) / Havells / Bajaj / Panasonic / Crompton / Jaquar / Lighting Technologies / Halonix ) | — | 20.00 | — | — | |
| — | — | — | Above/ 110132.00 Below/P | ||
| Supply of Vertical TPN DB with MCCB Incomer ( Metal Enclosurewith Metal Door - IP43 ), 3Ph, 50Hz, 415V, 8 way per phase, 415V, 50Hz, complete with total 24 nos. SP MCB of current rating from 6A to 32A, 10 KA, 240 Volt, 50 Hz per phase as perrequirement of load and one no. MCCB, 4 Pole, ( 40 - 100 ) Amp,415V, 50Hz, 36kA, ( Ics = 100% Icu ), Microprocessor based release with following features :- 1) Adjustable Over Load, 2) Adjustable Short Circuit, 3) Inbuilt ground fault protection, 4) Inbuilt Instantaneous protection, 5) Adjustable neutral overload protection, 6) Provision of Thermal Memory, 7) Microprocessor protection-based MCCB must have facility of individual 'LSIG' fault indication. ( Make of MCB, MCCB and Metal DistributionBoard - LK (L&T) / Siemens / ABB / Hager / Legrand / Schneider /C&S ) | — | 2.00 | — | — | |
| — | — | — | Above/ 5506.00 Below/P | ||
| Fixing, connection and commissioning of above panel with suitable arrangement including all incoming and outgoingcable glanding, socketing and connection with suitable cable termination arrangement. | — | 2.00 | — | — | |
| — | — | — | Above/ 777108.00 Below/P | ||
| "Supply of LT Wall Mounted / Floor Mounted Double Door Cubical Outdoor type Distribution Panel Board made of 14 SWG ( 2mm ) MS sheet duly powder coated comprising with the following items for 250KVA to 300 KVA Load : a) MCCB, 4 Pole, ( 160 - 400 )Amp, 415V, 50Hz, 36kA, Microprocessor based release for O/L, S/C, E/F & Neutral protection Model : LK (L&T) DN3-400D160- 400 A, MTX2.0, CAT No. -CM93003OOOOAG or equivalent - 2 nos. b) MCCB, 4 Pole, ( 100 -250 )Amp, 415V, 50Hz, 36kA, Microprocessor based release for O/L, S/C, E/F & Neutral protection Model :- LK (L&T) DN2-250D 100-250A, MTX2.0, CAT No. -CM92151OOOOAG or equivalent - 2 nos. c) MCCB, 4 Pole, ( 40 - 160)Amp, 415V, 50Hz, 36kA, Microprocessor based release for O/L, S/C, E/F & Neutral protection Model : LK (L&T) DZ1-160D 40-160 A, iTRP3, CAT No. - DZ1F0160DXH1A or equivalent - 2 nos. d) MCCB, 4 Pole, ( 25 - 100 )Amp, 415V, 50Hz, 36kA, Microprocessor based release for O/L, S/C, E/F & Neutral protection Model : LK (L&T) DZ1-160D25-100 A, iTRP3, CAT No. -DZ1F0100DXH1A or equivalent - 6 nos. e) MCCB, 4 Pole, 400 Amp, 415V, 50Hz, 36kA, without protection release, used as buscoupler isolation. Model : LK (L&T) DN3B-400SD - 400 A, CAT No. -CM98412OOROOG or equivalent - 1 no. f) RCBO, 4 Pole, 32 Amp, 415V, 50Hz, 10kA, Sensitivities -300mA, Suitable for AC +Pulsating DC (Type A) +Harmonics - 4 nos.g) RCBO, 4 Pole, 63 Amp, 415V, 50Hz, 10kA, Sensitivities - 300mA, Suitable for AC + Pulsating DC (Type A) +Harmonics - 6 nos. h) Tinned Copper Busbar (4 Bar) each of capacity 600 Amps., 415V, 50Hz. - 1 set. i) Static Multifunction panel mounting Energy Meter suitable for operation on 3Ph, 415V, 50Hz supply, Accuracy CL1 and RS485 Communication port Model : LK (L&T) MFM 4410, CAT No.-WL441011OOOO or equivalent - 12 nos. j) CT of suitable ratio for MFM - 36 nos. k) LED indication lamp for 3-Phases for incoming feeders and ""ON, OFF & TRIP"" indication for all incoming and outgoing feeders - 64 nos. l) Petty Store for control cable, MCBs, gland, socket, fuse, push button,TNC switch, selector switch, rotary handle operating mechanism, spreader terminals, interlocking arrangement, auxiliary contacts, shunt release, terminal blocks & NO/NC relays etc.- 1 job m) Fabrication work for above panel - 1 job. complete with internal wiring by single core FRLS grade copper conductor cable of suitable size and 1100V grade."( Make - LK (L&T) / Siemens / ABB / Hager / Legrand / Schneider / C&S / Havells QTRON ) ( Make for Energy Meter - ABB / Schneider / Secure / Legrand / LK (L&T) / Genus / Conzerv /Elmeasure / Stelmec / HPL / Socomec / Anchor / C&S ) | — | 1.00 | — | — | |
| — | — | — | Above/ 38856.00 Below/P | ||
| Fixing, connection, testing and commissioning of above panelincluding all incoming and outgoing cables glanding, cable socketingand connection and construction of concrete foundation orsuitable wall hanging arrangement as per site condition withall associated accessories | — | 1.00 | — | — | |
| — | — | — | Above/ 75300.00 Below/P | ||
| Supply, installation and commissioning of different size and suitable width self- illuminated LED display system with all necessary accessories :1) Aluminium panel - 3mm Pvdf coated aluminium composite panel.(Make-Alstone/Aludecor/Alstom/ Timexbond ) Designed artwork by ER shall be onrouter cut 3D alphabets of 2" depth to be flushed with the ACP sheet. 2) 1" X 1" 18g MS square pipe structure with red oxide and white enamel paint, ISI marked. 3) Imported translucent Acrylic sheet for making alphabets : a) Physical form - Sheets b) Thickness range - 3mm (+/-) 0.5mm c) Colour - White mild translucent d) Outdoor Stability - UV Stabilised e) Output - Excellent to cast Vinyl and self display f) Make - acast / Mitsubishi / sumiplex 4) 26g Galvanised iron sheet / 3mm acp for back panel. ( Make - Tata / Jindal / Bansal ) 5) Light Emit--ting Diodes ( LED ) sign modules - ( Make of LED chip - NICHIA/ CRE / OSRAM/ SEOUL/ PHILIPS/ LUMILEDS/ AVAGO ) a) Power consumption - 1 W each module b) Operating Temperature - (-) 40 degto 60 deg C c) Viewing Angle - 150 degree d) Input Voltage - 12V DC e) Protection Class inbuilt - IP 66 or higher f) Standards - UL94HB g) Certifications - UL. CE. C tick. ROHS h) Housing material of the module - PC & ROHS compliant i) Colour - White / Red / Warm white 6) Power Drivers -( Make-Union / Meanwell or similar ) a) Protection Class - IP 65 b)Rated Supply Voltage - 108V - 305V AC c) Fre--quency - 50/60 Hz d) Power Factor - greater than0.9 e) Driver Output current - .8A to 25 Ampere f) Operating Temperature - (-) 40 deg to 60 deg C g) Output Voltage Tolerance -10% | — | 100.00 | — | — | |
| — | — | — | Above/ 32300.00 Below/P | ||
| Supply, installation and commissioning of different size and2 inch width self- illuminated LED display system with all necessary accessories :1) Aluminium panel - 3mm Pvdf coated aluminium compositepanel. ( Make - Alstone / Aludecor / Alstom / Timexbond )Designed artwork by ER shall be for Flat cutting alphabetsto be flushed with the ACP sheet.2) 1" x 1" 18g MS square pipe structure with red oxide and white enamel paint, ISI marked.3) Imported translucent Acrylic sheet for making alphabets :a) Physical form - Sheetsb) Thickness range - 3mm (+/-) 0.5mmc) Colour - White mild translucentd) Outdoor Stability - UV Stabilisede) Output - Excellent to cast Vinyl and self displayf) Make - acast / Mitsubishi / sumiplex4) 26g Galvanised iron sheet / 3mm acp for back panel.( Make - Tata / Jindal / Bansal )5) Light Emitting Diodes ( LED ) sign modules -( Make of LED chip - NICHIA / CREE / OSRAM / SEOUL /PHILIPS / LUMILEDS / AVAGO )a) Power consumption - 1 watt each moduleb) Operating Temperature - (-) 40 degree to 60 degree C c) Viewing Angle - 150 degreed) Input Voltage - 12V DCe) Protection Class inbuilt - IP 66 or higherf) Standards - UL94HBg) Certifications - UL. CE. C tick. ROHSh) Housing material of the module - PC & ROHS complianti) Colour - White / Red / Warm white6) Power Drivers - ( Make - Union / Meanwell or similar )a) Protection Class - IP 65b) Rated Supply Voltage - 108V - 305V ACc) Frequency - 50/60 Hzd) Power Factor - greater than 0.9e) Driver Output current - .8A to 25 Amperef) Operating Temperature - (-) 40 degree to 60 degree Cg) Output Voltage Tolerance - 10% | — | 50.00 | — | — | |
| — | — | — | Above/ 261300.00 Below/P | ||
| Design, manufacture, display of wall / hanging / floor mounting type LED illuminated sign / direction boards in half elliptical shape.The display sheet shall be of unbreakable 040 translucent polycarbonate sheet of 2 mm thickness.The text / graphics matter visibility shall not be less than 160 deg. The approved colour text and graphics shall be printed / router cut on monomeric calendered vinyl of 70 um thickness and shall be firmly pasted on display sheets. The mounting arrangement shall be hanging, wall mounting, ceiling mounting, pole mounting or floor mounting and as per site requirement. The signage shall have the integral mounting arrangements with sturdy structural frame and ACP cladding on the back side of the signage to avoid rusting and entry of dust.The LED board shall have uniform illumination with 4-8 W / sq. ft and with brightness more than ambient light. Suitable size end cap of 1.5 mm thick SS 304 should be provided . | — | 100.00 | — | — | |
| — | — | — | Above/ 26200.00 Below/P | ||
| Erection and installation of wall / hanging / floormounting type LED illuminated sign / direction boards in half elliptical shape. The display sheet shall be of unbreakable 040 translucent polycarbonate sheet of 2 mm thickness. The text / graphics matter visibility shall not be less than 160 deg. The approved colour text and graphics shall be printed / router cut on monomeric calendered vinyl of 70 um thickness and shall be firmly pasted on display sheets. The mounting arrangement shall be hanging, wall mounting, ceiling mounting, pole mounting or floor mounting and as per its requirement. The signage shall have the integral mounting arrangements with sturdy structural frame and ACP cladding on the backside of the signage to avoid rusting and entry of dust. The LED board shall have uniform illumination with 4-8 W / sq. ft and with brightness more than ambient light. Suitable size end cap of 1.5mm thick SS 304 should be provided. | — | 100.00 | — | — | |
| — | — | — | Above/ 3248.00 Below/P | ||
| Supply of LED Signage Board containing script of officer'sdesignation made of high quality acrylic 8mm sheet with laser make - acast / ub / astari, in aluminium extruded slot of 24g and Light Emitting Diodes - Red & Green ( Make / brand of LED chip - NICHIA, OSRAM, SEOUL, PHILIPS, LUMILEDS, AVAGO, CREE ) complete with necessary electronic driver and all other accessories including fixing, connection, testing and commissioning of LED Signage Board with suitable clamps / fixtures | — | 2.00 | — | — | |
| — | — | — | Above/ 56232.00 Below/P | ||
| Supply of Maintenance Free Copper Bonded Solid EarthingRods with 25 kg Earth Enhance Compound with belowspecifications :a) Certified by CPRI and NABL Accredaited Labb) ROHS certifiedc) Low Carbon High Tensile Rodd) Length of Electrode 3000 mm (3 Meter)e) Rod dia 17.2 mmf) Molecular Copper Plating thickness 254 microns as per UL 467g) Connection terminal size 32 mm x 6 mm with 10 mm hole along with nut bolt and washerincluding installation, testing and commissioning as per RDSOspec. no. RDSO/SPN/197 ver. 1.0 or latest and conforming toRDSO Drg. No. SDO/RDSO/E&B/001 or latest.( Make : ABB / VTR / Raychem / Veraizen Earthing / Ennob / True Power Ltd. / OBO Bettermann ) | — | 6.00 | — | — | |
| — | — | — | Above/ 3954.00 Below/P | ||
| Supply of Heavy Duty Fiber Reinforced Polymers Pit Coverwith below specifications :a) Weight Carrying Capacity 5 Tonb) Lockable arrangementc) Top Dia 162 mmd) Bottom Dia 242 mme) Height 230 mmf) As per IEC 62561-5g) M5 Nut Bolts HDG 4.6, 30 mm length with 2 nos. of plain washerh) Tested by NABL Accrediated LABincluding installation, testing and commissioning.( Make : ABB / VTR / Raychem / Veraizen Earthing / Ennob / True Power Ltd. / OBO Bettermann ) | — | 6.00 | — | — | |
| — | — | — | Above/ 49132.00 Below/P | ||
| Sub-station earth by supply, digging and insertion of earth pipemade of heavy gauge GI pipe of size 50 mm dia x 3 mtrs.long ( Make - Tata / Jindal / Bansal ) including construction of total4 nos. earth pit as per Sr.DEE/G/E.Rly/HWH's drg. no. Misc./10/Rev. Each earth pit provided with 3 nos. of above pipe duly sorted by GI strip of size 50 mm x 6 mm including necessary earth connection from pit to CSS / HT / LT panel board / transfor-mers etc. by GI strip of size 50mm x 6mm with GI nuts & bolts. | — | 2.00 | — | — | |
| — | — | — | Above/ 30294.00 Below/P | ||
| Supply of Gl Flat for Earth Bus including connection from"earth pit and fixing and commissioning on Sub-station "building wall by Gl nut-bolts and washer with supporter for earthing of HT and LT equipments | — | 0.50 | — | — | |
| — | — | — | Above/ 9948.00 Below/P | ||
| Earthing with 2 nos.of 50 mm diametre, 3.0 metres long heavy gauge GI pipe ( Make - Tata / Jindal / Bansal ) including construction of earth pit and necessary earth connection from pit by suitable Galvanized Iron ( GI ) strip.( For details not covered in this specifications, IndianStandard Code of Practice for earthing IS : 3043 - 1987,Reaffirmed - 1996 should be followed ) | — | 4.00 | — | — | |
| — | — | — | Above/ 7688.00 Below/P | ||
| Installation, testing and commissioning of 1.5 TR Split AC machine including outdoor unit with MS angle stand along with necessary power cable and all other accessories.( Split AC machine will be supplied by Railway ) | — | 4.00 | — | — | |
| — | — | — | Above/ 13770.00 Below/P | ||
| Installation, testing and commissioning of 2 TR Split AC machine including outdoor unit with MS angle stand along with necessary power cable and all other accessories.( Split AC machine will be supplied by Railway ) | — | 6.00 | — | — | |
| — | — | — | Above/ 100350.00 Below/P | ||
| Supply of Refrigerant Copper Pipe line of required size and length with nitrile rubber insulation and all other accessories including fixing, testing and commissioning of above pipe line for above Split AC units. | — | 150.00 | — | — | |
| — | — | — | Above/ 30900.00 Below/P | ||
| Supply of Drainage system for each above Split / Window AC machine for discharge of condensate water with all accessories by 1.5 inch dia PVC pipe and drain line of each machine connectedby 0.5 inch cotton braided PVC flexible pipe with all other accesso-ries along with fitment and commissioning. | — | 300.00 | — | — | |
| — | — | — | Above/ 45150.00 Below/P | ||
| Supply of Copper Flexible 4C x 4.0 sq. mm.control cable and cabling between outdoor and indoor units as per OEM specification bundled properly and neatly aligned with the refrigerant piping with well supported at specific intervals with fasteners including erection, testing and commissioning .( Make of Copper cable - Anchor / KDK / Havells /Finolex / Gloster / KEI / Polycab / RR Kabel / Mescab ) | — | 150.00 | — | — | |
| — | — | — | Above/ 1109969.00 Below/P | ||
| Goods & Services Tax ( at present @ 18% ) | — | 1.00 | Lumpsum | — |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Advancecorrectionslipsupto11.pdf
ATTACHMENT
TenderBooklet.pdf
ATTACHMENT
GCC_April-2022.pdf
ATTACHMENT
TenderFormandAnnexuresnew.pdf
ATTACHMENT
HTLTstandardspecification.pdf
ATTACHMENT
AnnexureVIB.pdf
ATTACHMENT
Annexure-VA.pdf
ATTACHMENT
Drg.No.-MISC-10-REV.pdf
ATTACHMENT
DetailTechnicalSpecificationTC3664.pdf Detail Technical Specification
ATTACHMENT
3664Clause.pdf
ATTACHMENT
DetailTechnicalSpecificationTC3664.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .