WB-HMC/TN/ED/SS/10/25-26_1

Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. In Gr floor P-11,I-10

Dismantling carefully wooden walling, flooring of ceiling and stacking dismantled materials as directed. P-13 It-17 PWD BLDG

Extra for staging beyond 4 m in any floor (Mode of measurement: area in plan x mean height of staging upto soffit of shuttering above initial 4 m) P-42 It-36/ e PWD BLDG.

(a) Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification [Cement to be supplied by the Department] P-45,I-8(a)

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:4 cement mortar(b) 15 mm thick plaster.3rd cor P-49,I-1(ii)ground floor

Spot application for insecticides using Aqua base spray for pest (for bugs, cockroaches, silverfish, spider, termites, mosquitoes) to walls and ceiling etc. with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight including spraying the emulsified chemical @ 0.5 litres per sq.m. by a hand operated pressure pump on wall surfaces, ceiling, electrical fixture,electrical lines including drilling holes inplaces where source of termite is detected squirting chemical solution into the holes and sealing the holes with cement grout. (Rate is per sq.m. of the floor area while actual work will be all walls ceiling, rack, partition and furniture).P-9 It-11/e PWD BLDG.

Dressed wood work in post , plate , battens . etc. fitted & fixed complete (excluding the cost of bolts only, but including the cost of nails, screws etc.) (The quantum should be corrected upto three decimals) Sal : Malayasian.P-135 It-1/B/iii PWD BLDG.

Supplying solid flush type doors of deluxe decorative (both side) quality, conforming to I:S 2202 timber frame consisting of top and bottom rail and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 27.5mm wide battens places both ways in order to made the door of solid core and internal lipping with teak, mahogony or rose wood approved decorative veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing the shutters in position but excluding the cost of hinges and other fittings in ground floor: 35mm thick shutters (single leaf)P-124 It-12/a PWD BLDG.

Supplying fitting & fixing frames for Fire resistant acoustic door shutters 1st class Malaysian Hardwood Frame (densified to 810 kg/cum) and pressure treated with fire retardant chemicals in vacuum impregnation vessel under 160 psi pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 of section 120 mm X 70 mm spray quoted with 2 coats of intumescent paint of minimum 200 micron, with standard double acoustic seal (equivalent to Hafele) placed along two faces of rebate for sound insulation and single row of Brush- Type intumescent strip of size 10 mmx 4 mm affixed in the slit of the Frame for fire and smoke sealing, etc. complete as per direction of Engineer - inCharge including a protective coat of painting at the contact surfaces of the frame excluding cost of concrete,Iron butt hinges and M.S clamp at Ground Floor.PWD BLDG P-283 It-5

Supplying & fitting of 65mm thick asbestos free - fire, heat and smoke resistant composite Accoustic Door Shutter complying with fire performanceFD120 as per IS:3614 (part -II)-comprising of 2x 8 mm Calcium Silicate boards over Chemically treated (with Fire retardant chemicals in pressure impregnation vessels under 160 psi pressure as per IS:401 and kiln seasoned to moisture below 15% as per IS:1141) internal timber (Malaysian Hard Wood,densified to 810kg/cum ) frame work of 100 mm x32 mm with 32mm thick infill of ceramic fiber (density 128Kgs/cum), vermaculite mix faced with 6 mm Fire retardant High Density fire board, internally lipped with hardwood beading, and pasted in Hydraulic Press under 25 MPa, spray coated with 2 coats of in-tumescent paint of minimum 200 micron, and with 1 row of Brush- Type intumescent strip of size 10mmx 4mm affixed on peripheral slit on all edges of shutter except bottom for fire and smoke sealing and placement of 3 mm thick rubber membrane, at the inside face, sandwiched between calcium silicate board & high density fire retardant board , without any external lipping including fitting ,fixing shutters in position but excluding the cost of hinges & other fittings as per direction of Engineer -in -charge complete in all respect in Ground Floor.PWD BLDG P-285 It-7

Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm long M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer‟s specification and direction of Engineer-in-Charge.P-115 It-4 PWD BLDG.

Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge. In ground floor.P-125 It15 PWD BLDG

Supplying, fitting and fixing boiling water resistant ply conforming to IS: 303- 1989 bonded with phenol formaldehyde synthetic resin of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-inCharge.[excluding the cost of supporting frame work and teak wood batten/Lipping] In Ground Floor 6mm.P-173 It-3/ii PWD BLDG.

16 mm.P-173 It-3/V PWD BLDG.

Supplying, fitting and fixing boiling water proof block board conforming to IS:1659-1990 conforming to IS:848-1974 of approved make and brand, fitted and fixed as per design as per direction of Engineer-in-charge. [Excluding the cost of supporting frame work and teak wood batten/Lipping]. In Ground Floor P-173 It-4/i.16mm

Supplying wooden moulding slanting beat of size 37mm X 18mm (finished) of approved design to finish the joint between wooden frame of door/window with masonary in true line and level fitted & fixed with adhesive and head less pins complete as per direction of Engineer -in-charge.b) Kappoor wood beat.P-147 It-38/b

Partition of teak veneer [1 mm] as per design fitted and fixed complete (excluding the supporting frame work & necessary teak wood battens): In ground floor (i) 4mm thick commercial quality P-180 It-18 PWD BLDG.

French polishing to wood work including preparing surface (ordinary gloss).On new surface .P- 202 It-11/a PWD BLDG.

Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark.100mm. X 75mm. X 3.50mm.P-140 It-5/viii PWD BLDG.

Supplying, fitting & fixing Stainless Steel 'D' or 'H' type of size 300 mm x 19 mm tubular Handle with Grade 304, CE certified, marked & conforming to EN - 1154, of approved quality of reputed brand as per direction of Eingineer-inCharge fitted and fixed complete including all incidental charges.P-291 It-18 PWD BLDG.

Supplying, fitting fixing Godrej type hydraulic (oil check) floor door spring, heavy duty double action with brass shoe, brass top centre aluminium top cover etc. complete set as per direction of Engineer-in-charge.P-147 It-37 PWD BLDG.

Godrej Hydraulic door closer fitted and fixed complete. Heavy type.P-143 It-23/ii/a PWD BLDG.

Door stopper.(Brass).P-143 It-19/I PWD BLDG.

Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: 150mm long x 12mm dia. bolt P-144 It-26/v PWD BLDG.

300mm long x 12mm dia. Bolt P-144 It-26/x PWD BLDG.

Anodised aluminium grip handle with base plate of approved quality fitted and fixed complete.(a) With base plate (i) 165mm grip x 12mm dia rod x 42mm plate x 3.2mm thick.P-146 It-33/a/I PWD BLDG.

Brass hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting 300 mm long.P-142 It-10/ii/c PWD BLDG.

Supplying and fitting in all places of wall panelling to all heights and fixing on pre- framed existing frame work grid with glass wool of 50mm thick having density of 48 Kg per cum. to be inserted into the pre - fabricated slot covered the glass wool by marking cloths treated with Naptha @ 0.07 Ltr.per Sq.m. of cloths. Finally 12.5mm thick gypsum Fulton board having size 595mmX595mm fitted & fixed into the pre-fabricated grid and covered the all perifirial gaps of fulton board by self additive fibre tape with necessary filler if required, complete in all respect as per direction of the Engineer-in-charge. P-177 It-12 PWD BLDG.

Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of Engineer-incharge.The rate includes the cost of labour, adhesive and all incidental charges thereof. In ground floor.Thickness of laminate 1.5 mm.P-179 It-14 PWD BLDG.

Scantling upto 50mm wide and 12mm thick (chamfering or rounding) for ceiling/partion battens including fitting, fixing in position with washers, coach screws etc. complete.:(a) Ordinary teak.P-137 It-7/a PWD BLDG.

Dismantling artificial stone flooring upto 50 mm. thick by carefully chiselling without damaging the base and removing rubbish as directed within a lead of 75 m.b) Extra for each addl. Floor over the rate of gournd floor.P-11 It-6/b

Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous & Granular finish Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007 and testing shall be made in accordance with IS:13630 [Non- modular sizes for tiles with Skid resistance > 0.5, Mohr's hardness > 5.0, Staining resistance: Class-1, Water Absorption: E < 0.5%], MOR > 35 N/sq.mm in Internal area of building e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thick layer applied directly over finished artificial stone floor/ Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor)In Ground Floor: Sizes-600 mm x600mm x10 mm with breaking strength > 1500 N P-280 It-1/b PWD BLDG

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. P-65 It-35/D/b/I PWD BLDG.

Repair & Renewing of Mid Back Auditorium room Chair including all charges having Specification:- The seat shall made of Polyurethane Foam moulded with 1.5±0.1cm. thk. plywood insert measured as per QA method and upholstered with fabric. Seat Size (approx.) Depth: 42.0cm x Width @Rear: 44.0cm x Width @Front: 41.0cm. The back assembly shall be flexing type and made of Polyurethane Foam with density = 45 +/-2 kg/ m³.. The back cover and mechanism cover are vacuum formed from black ABS sheets. The Armrest understructure is upholstered PU foam moulded with MS insert. Arm tops are made of black Integral Skin polyurethane with 50-70 Shore 'A' Hardness & reinforced with wooden insert. Armrest width = 7.0±0.5cm and are offered as common / individual armrest between chairs. MS black powder coated (DFT 40-60 microns) understructure with integrated, auto tip-up mechanism which folds the seat when not is use. Footprint area of base plate: made of HR steel 15.0±0.2cm x 22.0±0.2cm x 0.5±0.05cm thick. Backrest supporting beam width: 46.0±0.2cm(L) x 8.0±0.03cm x 4.0 ±0.03cm x 0.2±00.16cm MS tube. Understructure fixed to ground by anchors with washer and nut. document as per direction of Engineer-in-ChargeRate by National Council of Science Museums) Ministry of Culture, Government of India ENit-SCCY-15014/30(408)/2019 at Science city,kolkata Auditorium Chairs

Supplying & laying of approved brand of scratch proof, semi flexible P.V.C. blended homogeneous marble Vinyle flooring in tiles conforming to IS:3461, fixing with synthetic acrylic adhesive after preparing the floor, levelling & smothaning when necessary with suitable putty, as per the design & instruction of the Engineer-in-charge. 2 mm thic P-76 It-1/A PWD BLDG.

Supply, Fitting, Fixing & Placement Carpet for Auditorium Room including all charges Having Specification:- Construction of the Roll carpet will be Graphic level loop, Fibre will be woven polypropylene & solution dyed. Pile weight of the carpet wil be Ca. 700 gr/m2 & total weight will be Ca 2,200 gr/m2 & Pile height will be Ca. 5mm. Primary backing of the carpet will be woven polypropylene & secondary backing will be action back semi-commercial wear & Anti shock Carpet as per direction of Engineer-in-Charge. Rate approved by HMC EOB dept,

Suppling, fitting and fixing Wall mounted water closet of white glazed vitreous chinaware of approved make and brand in position complete with necessary nut and boalts (Equivalent to Code No. 20061 or 92065 & Model Studio or Rubbic of Hindware or equivalent.)P-79 It-5 PWD S&P

Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete.Bestolite (solid type) white.P-81 It-10/a/iv PWD S&P

Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete. Polythene Flush Pipe.P-81 It-11/I PWD S&P

Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete(i) 635 mm X 395 mm X 420 mm.P-80 It-6/I PWD S&P

Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete.ii) C. P. Flush Pipe.P-81 It-11 PWD S&P

Supplying, fitting and fixing urinal flush pipe fittings of approved brand. C.P. urinal flush pipe fittings range of one.P-81 It-12/a PWD S&P

Supplying, fitting and fixing porcelain partition wall of approved make of size 618 mm X 310 mm complete in all respect.P-81 It-14 PWD S&P

Supplying, fitting and fixing glass shelf with aluminium guard rails.(a) Ordinary type with 5.5 mm sheet glass(ii) 600 mm X 125 mm P-81 It-16/a/ii PWD S&P

Supplying, fitting and fixing soap holder.(a) PTMT (Prayag or equivalent) P-82 It-18/a PWD S&P

Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm.P-82 It-19 PWD S&P

Supplying, fitting and fixing towel rail with two brackets.(b) Aluminium(i) 25 mm dia. and 450 mm long.P-82 It-22 PWD S&P

Supplying, fitting and fixing 10 litre porcelain low-down cistern of approved make with either side or bottom inlet, side overflow, brackets complete with all internnal PVC fittings.White.P-36 It-1 PWD S&P

Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint.(iii) 630 mm X 450 mm size.P-41 It-2/iii PWD S&P

Supplying, fitting and fixing pedestal of approved make for wash basin (white).P-41 It-3 PWD S&P

Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.(iv) 750 mm long.P-43 It-9/iv PWD S&P

Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps.(ii) 750 mm long.P-43 It-10/ii

Supplying, fitting and fixing Waste fittings complete.(a) C.P. over brass(ii) 32 mm.P-44 It-17/a/ii

Supplying, fitting and fixing pillar cock of approved makec) CP Pillar Cock - 15 mm.P-45 It-19/c

CP 2-way bib Cock - 15 mm, supplied, fitted and fixed.P-45 It-19/f/ii

Hand Shower(Health Faucet) with 1mtr Fexible Tube with Wall Hook.P-4 It-3/f

Chromium plated angular Stop Cock with wall flange.P-6 It-7/d/i

Chromium plated concealed Stop Cock heavy dutyP-6 It-7/d/ii

Chromium plated Bib Cock long body with wall flange with aerator.P-6 It-7/a/ii

Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) For Concealed work 15 mm P-2 It-1/B/a

20 mm P-2 It-1/B/b

25 mm P-2 It-1/B/c

32 mm dia. medium quality P-2 It-1/A/d/II

Dismantling Indian W.C. including taking out base concrete as necessary.P-85 It-2

Dismantling urinal.P-85 It-8

Dismantling flush pipe of water closet.P-85 It-10

Supplying, fitting and fixing Peet's valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.). P-4 It-4 25 mm

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 . Single Socketed 3 Meter Length 75 mm.P-68 It-23/A/i

Plain Floor Trap with Top tile & Strainer - 75 mmP-72 It-23/A/XXXi

Supplying, fitting & fixing Cast iron soil pipe only conforming to I.S. 3989/ 2009 and I.S. 1729/2002 with bobbins, nails etc. including making holes in the wall, floor etc. and cutting trenches etc. in any floor through masonry concrete, if necessary, and mending good damages with necessary jointing materials and painting two coats to the exposed surface with approved paint complete. (Measurement will be made along the center line of the total pipe line in fitted condition including specials,payment for specials & Painting will however be paid seperately 100 mm dia. (internal)P-60 It-1/a/ii

Supplying, fitting & fixing Cast iron single branch equal with door conforming to I.S. 1729/2002 including joining and painting two coats to the exposed surface with approved paint complete. (Payment of Painting will however be paid seperately). (a) With valamoid joints inclu. sealing the top with cement mortar (4:1) 100 mm.P-60 It-2/ii

Supplying, fitting & fixing H.C.I. bend with door conforming to I.S.S. including jointing complete and painting two coats to the exposed surface with approved paint complete. (Payment of Painting will however be paid seperately). (a) With valamoid joints includ. sealing the top with cement mortar (4:1) 100 mm.P-60 It-4/ii

Supplying, fitting & fixing H.C.I. bend without door conforming to I.S.S. including jointing complete and painting two coats to the exposed surface with approved paint complete. (Payment of Painting will however be paid seperately). (a) With valamoid joints including sealing the top with cement mortar (4:1) 100 mm.P-61 It-5/ii

Supplying, fitting & fixing H.C.I. offset conforming to I.S.S. including jointing complete with or without ear (75 mm projection) and painting two coats to the exposed surface with approved paint complete. (Payment of Painting will however be paid seperately). (a) With valamoid joints including sealing the top with cement mortar (4:1)100 mm.P-63 It-7/ii

Supplying, fitting and fixing cast iron extension pipes for using in Traps only (connector) conforming to I.S.3989/2009 and 1729/2002 including lead caulked joints complete and painting two coats to the exposed surface with approved paint complete. (Payment of Painting will however be paid seperately) 100 mm x 300 mm.P-66 It-15/A/iii

Supplying, fitting & fixing approved patent vent cowl I.C.I. conforming to I.S.S and painting two coats to the exposed surface with approved paint complete. (Payment of Painting will however be paid seperately). (i) 100 mm diaP-64 It-9

Supplying, fitting & fixing Cast iron double branch equal with door conforming to I.S. 1729/2002 including jointing and painting two coats to the exposed surface with approved paint complete. (Payment of Painting will however be paid seperately). (a) With valamoid joints including sealing the top with cement mortar (4:1) 100 mm.P-61 It-3

Providing and fixing of factory made uPVC Louver window (White Colour) (U value=1.9-1.3 W/m 2 K, flame resistant, self extinguishing, lead free) comprising of uPVC multi-chambered with wall thickness of 2.3mm (±0.2 mm ) duly reinforced with 1.6 mm (±0.2 mm) thick G. I. Section made from roll forming process of required length (shape & size according to uPVC profile Louver Window (Adjustable Louver Only) frame of size 67 x 62 mm both having wall thickness of 2.3 ± 0.2 mm .P-298 It-27/b

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.P-200 It-1/b

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : On timber or plastered surface.P-200 It-2/A/a/iv

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor).Two Coats.ii) Solvent based interior grade Acrylic Primer.P-195 It-7/b/ii

Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) :(Two coats)ii) Luxury QualityP-201/I-4

Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick)P-198/I-5

(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.P-200,I-1(a)

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface : With super gloss (hi-gloss) - (iv) Two coats (with any shade except white) P-200,I-2(b)(iv)

Supplying&FixingCRCsheet metal (16SWG) JB-cum SwitchBoardof the followingsizescompletewiththreeno. suitablesizeCopperbarwithholes(forPh,N&E) fixedon bakelite/HardRubberinsulatorovertheMSweldedchairsincl. bakelite/Perspex/colouredPerspex(wallmatchingcolour) top cover3mmthick flushed inwall forhousingtheboardafter cutting the brick wall incl. making earthing attachment, painting and mending good damages to building works 300 mm x 200 mm x 65 mm PWD/Elec. works/2017/P E-3/1-10(E)

Supply&Fixing bakelite / perspex top cover on existing switchboardbyBrassscrewsaftermakinghousingforswitch by cuttingbakelite / perspexcover andmakingnecessary connections as required 300 mm x 200 mm x 65 mm PWD/Elec. works/2017/P E-4/1-12 (D.G)

Supplyingandfixingdouble-doorSPNMCBDistribution BoardwithIP-42/43protection,concealedinwallafter cutting the wall &mending good the damages to original finishincl. Interconnectionwithsuitablesizeof copperwireandneutral link&provision for earthing attachment. 2+10 way PWD/Elec. works/2017/P D-10/1-13

Supply&Fixing 240V6APianokeytypeswitch(Brand approvedbyEIC)onexistingsheetmetal switchboard havingbakelite/perspextopcoverbyscrewsaftermaking housingforswitchbycuttingbakelite/perspexcoverand making necessary connections as required

Supply&Fixing 240V16/20APianokey typeswitch (BrandapprovedbyEIC)onexistingsheetmetalswitch boardhavingbakelite/perspextopcoverbyscrewsafter making housing for switch by cutting bakelite/perspex cover and making necessary connections as required PWD/Elec. works/2017/P E-5/1-14(A,B)

Supply&Fixing240V,6Aplugsocket (Brandapproved byEIC), without switch&plug top, onexisting sheet metal switchboardwithbakelite/perspex top cover by screws after making housing for plug by cutting bakelite/perspextopcoverandmakingnecy.connections with PVC wire and earth continuity wire etc

Supply & Fixing 240 V, 20 A plug socket (Brand approved by EIC), without plug top and switch, on existingsheetmetal switchboardwithbakelite/perspex topcoverbyscrewsaftermakinghousingforcombined plug switchby cutting bakelite/perspex top cover and making necy. connections with PVCwire and earth continuity wire etc.

Supplying & delievery of led flood lights type - 50 watt

type - 100 watt ref: KMDA approve rate

supply & fixing of green led ultimate sqaure ( 6''x6'') including the false celing in dimension also the wiring and connection of the light by 1.5 sq mm cu wire complete make :- bajaj, 15 watt square/round

supply & fixing of green led ultimate sqaure ( 6''x6'') including the false celing in dimension also the wiring and connection of the light by 1.5 sq mm cu wire complete make :-havel, 18 watt square/round ref: irrigation & waterways/mech elec. Works/2022/9-118/I-5.3 G.3.1

Supply of lamps: Type PAR 64 GX16D /240V,1000W

Type PC Lamp T-11 ( Projection lamp)/240v,1000w KMDA Vetted Rate

Distribution wiring in 1.1 KV single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in 20mm size PVC rigid conduit 'FR' (Precision make) incl. necy. fittings as required 2x 36/0.3 (2.5 sqmm) + 1 x 22/0.3 (1.5 sqmm) ECC

2 x 56/0.3 (4 sqmm) + 1 x 36/0.3 (2.5 sqmm) ECC PWD/Elec. works/2017/P E-5/1-14(A,B)

Supply & Fixing 240 V, 25A Modular type socket, 25 A, Modular type starter (Brand approved by EIC) with 25A Modular switch type DP MCB (C-Curve) and 6 Module GI Modular type switch board with 6 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. PWD/Elec. works/2017/P E-19/1-18

Supply of cabin fan oscillating type with base, blades, guard, speed regulators etc 400 mm sweep ref: irrigation & waterways/mech elec. Works/2022/9-118/I-5.3 G.3.1

Fixing only cabin fan on wall/ceiling by S&F rag bolts, nuts & washers (6 mm dia x 62 mm long) or as reqd. incl. S&F 24/0.20 PVC insulated flexible copper wire 0.5 mt. length PWD/Elec. works/2017/P C-4/1-18

Supplyingandfixing240/415VMCBofBreaking capacity10kA&Ccharacteristicsondin rail of existing DBs and necessary connection 6-32 A

63 A PWD/Elec. works/2017/P D-6/1-7

Supply and fixing of skycove LED Strip ( 5M length) with driver and necessary connection. Make: philips, led strip skycove 5m ww with driver ref: irrigation & waterways/mech elec. Works/2022/9-118/I-5.3 G.3.1

Add 18% GST

Add 1% Labour cess