Construction of Mukhya Mantri Lok Bhawan at Moolkoti, Development Block Mashobra District Shimla Himachal Pradesh. (SH Construction of Civil Works, Water Supply and Sanitary installation)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Providing form work with steel plates 3.15 mm (three decimal fifteen millimeter ) thick welded with angle iron in frame 30X30X5 mm (thirty into thirty into five millimeters )so as to give a fair finish including centering , shuttering ,strutting and propping etc. with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling & removal of same for in-situ reinforced concrete and plain concrete work in .

Foundation ,footing basis of columns etc. And mass concrete as per direction of the Engineer-in-charge including carriage of material with in all leads , lifts in all floor levels and other incidentalscomplete in all respect .

Columns, pillars ,posts and struts square, rectangular or polygonal in plan as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect .

Beams cantilever girders and lintels side and soffits of beams ,beams haunchings, cantilevers ,bressumers and lintels any depth in all heights from floor as per direction of the Engineer-in Charge including carriage of material with in all leads ,lifts in all floor levels and other incidentalscomplete in all respect .

Flat surfaces, such as soffits of the suspended floors roofs , landing and the like floors etc. up to any thickness , all as per direction of the Engineer-in Charge including s carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect .

Providing and laying, mechanically mixed and vibrated cement concrete (1:5:10 1 cement 5 sand 10 graded crushed stone aggregate 40 mm nominal size) including curing as required at site complete excluding the cost of form work but including all leads and lifts of materials in foundation and plinth and as per direction of Engineer -in -charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:3:6 (1 Cement : 3 coarse sand): 6 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete 1:1½:3 (one cement:one and half sand :3 graded crushed stone aggregate 20 mm (twenty millimeter) nominal size) mechanically mixed and vibrated graded crushed stone aggregate 20mm nominal size and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in :-

Foundation ,footing basis of columns etc and mass concrete as per direction of the Engineer-in-charge including carriage of material with in all leads , lifts and other incidentals complete in all respect.

Column , pillars , posts and structs as per direction of the Engineer-in Charge including carriage of material with in all leads and lifts and other incidentals complete in all respect.

Suspended Floors , roofs , landings shelves and their supports , balconies beams ,girders, bressumers and cantilever for all floors levels , complete as per direction of the Engineer-in Charge including carriage of material with in all leads ,lifts and other incidentals complete in all respect.

Providing tor steel reinforcement of TATA or SAIL make for reinforced Cement concrete work including bending, binding and placing in position and cost of binding wire complete for all floors including carriage of material with in all leads and lifts and other incidentals, complete in all respect.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm nominal size) at plinth level in cement mortar 1:6( 1 cement : 6 Sand).

Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) (Kiln seasoned and chemically treated hollock wood)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. including all leads and lifts of materials in foundation and plinth and as per direction of Engineer -in -charge.

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws. 2nd class deodar wood 35 mm thick.

4 mm thick glass pane (weight not less than 10 kg per sqm)

Providing 40 X 3 mm flat iron hold fast 40cm(forty centimeter) long including fixing to frame with 10mm(ten millimeter) diameter bolts & nuts and wooden plugs and embedding in cement concrete block 30 X 10 X 15 cm (thirty into ten into fifteen centimeter) 1:3:6 (one cement :three sand :six graded stone aggregate 20 mm nominal size), complete in all respect.

Providing and fixing mild steel plain M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws.

Providing and fixing Stainless steel sliding door bolts with nuts and screws etc. complete

Providing and fixing Stainless steel . tower bolts (barrel type) with necessary screws etc. complete.

200mmX10 mm

150mmX10 mm

Providing and fixing Stainless steel handles with the necessary screws etc. complete

Providing and fixing Stainless steel hooks and eyes. 150 MM

Providing and fixing 100mm bright finished brass floor Door stopers with rubber cushion screws etc to suit shutter thickness complete including carriage of material with in all leads and lifts, complete in all respect.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting,dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) (Dark shade pigment using ordinary cement)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and fixing 10mm(Ten milimeter )thick water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalent 600X600X 10 mm(six hundred into six hundred into ten milimeter )manufactured of approved sade and colour in flooring ,treads of steps and landing laid over 12mm (twelve milimeter)thick cement mortar 1:3 (1ceemt :3 sand ) jointed with ceemt slurry mixed with pigment to match the shade of tiles as required complete including carriage of material with in all leads lifts in all floors

Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm nominal size)laid in one layer finished with a floating coat of neat Cement. 40 mm Thick

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills,facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc.complete at all levels.Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Apply primer coat With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

15mm thick cement plaster in single coat on rough / fair side of brick /concrete/stone wall for interior / exterior plastering for all floors including arises internal rounded angles chafers and / or rounded angles chamfers and/ or rounded angles not exceeding 80mm (eighty millimeters )In girth and finished even and smooth in cement mortar 1:6 (one cement :six sand )as per direction of engineer in charge including carriage of material within all leads lifts in all floors and other incidental

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of material with in all leads and lifts.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat with cement primer

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/ stone/ plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for making the surface smooth.

Finishing wall with weather proof exterior grade emulsion of approved design (apexultima) or its equarlied on udecorated wall surfaces (Two Coats )to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matters etc. including sand paper smooth complete including carriage of material with in all leads and lifts.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and fixing vitreous china wash down closet (European type W.C. pan) of Cera , Hindware or equvalent ) with integral P or S trap including jointing the trap with soil pipe in cement mortar 1:1 (one cement : one sand) seat and cover to be measured and paid for separately anglo Indian universal closet as per direction and to entire satisfaction of Engineer-in-charge including carriage of material within all leads and lifts upto all floor levels.

Providing and fixing vitreous china wash down water closet squatting pan (Indian type W.C. pan) of Cera , Hindware or equvalent)of size 580mm (earth work bed concrete, trap to be measured and paid for seprately . Orissa pattern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

White Vitreous China Flat back wash basin size 450x 300 mm with single 15mm C.P. brass pillar tap

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bor

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore 15 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end25 mm nominal bor

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :510x1040 mm bowl depth 250

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing toilet paper holder C.P. brass

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc

15 mm (fifteen millimeters) nominal bore

20 mm (twenty millimeters) nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

15 mm (fifteen millimeters) nominal bore

20 mm (twenty millimeters) nominal bore

Providing and fixing PVC water storage tank of Sintex or equvalent make of ISI :12701 Marked ,G.I. inlet and outlet connection , 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground Level (1000 litres net capacity tank)including carriage of material upto all leads and lifts in all floor

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm nominal size (seventy five millimeters) size

110 mm nominal size (one hundred ten millimeters) size

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler 75 mm

Bend 87.5° 75 mm

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design Inside dimensions60mm x60mm x75mm deep for single pipe line

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Rectangular shape 600x450 mm internal dimensions

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated hickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet hould have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coatedthickness, Zinc coating 120 grams per sqm as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18microns using self drilling/ self tapping screws complete :12.51.1 Ridges plain (500 - 600mm)

Flashings/ Aprons.( Upto 600 mm)

Gutter (600 mm over all girth)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing & fixing false ceiling at all height including providing & fixing of framework made of special section,power pressed from M.S. sheets and galvanised withzinc coating of 120 gms/ sqm (both side inclusive) as perIS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at1200mm c/c, one flange fixed to the ceiling with dashfastener 12.5mm dia x 50mm long with 6mm dia bolts,other flange of cleat fixed to the angle hangers of 25 x10x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed withintermediate G.I chanels 45 x15 x 0.90mm running atthe spacing of 1200 mm c/c, to which the ceiling section0.5mm thick bottom wedge of 80mm with taperedflanges of 26 mm each having lips of 10.5mm, at450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made outof 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, theperimeter of ceiling fixed to wall/ partitions with the helpof Rawl plugs at 450mm centre, with 25mm long drywall screws @ 230mm interval, including fixing ofCalcium Silicate Board to ceiling section and perimeterchannels with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing & finishing to aflush finish of tapered and square edges of the board with recommended jointing compounds, jointingtapes,finishing with jointing compounds in hree layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the ngineer in charge but excluding the cost of painting with

Ashish Sharma (BID ID -503401)

rakesh (BID ID -503409)