Recalled for Special repair of Bharti Hostel Ladli Hostel and residences in Govt Postgraduate College for Women at Rohtak

Amount

Earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres. (HSR 6.6)

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing. (b) In cement. (HSR 8.5 b)

Centring and shuttering for flat surfaces such as suspended floors, Roofs, landings, chhajjas, shelves etc. inclination not exceeding 25 degree with horizontal. (HSR 9.1) (a) 1st Storey.

2nd Storey

Centring and shuttering for sides and soffits of beams haunchings, girders, bressumers and lintels. (HSR 9.7) (a) 1st Storey.

2nd Storey

Centring and shuttering for columns (square or rectangular or Polygonal in plan). (HSR 9.9) (a) 1st Storey.

2nd Storey

Shuttering for faces of concrete foundations and foundations beams (vertical or battering). (HSR 9.13)

Cement concrete 1 : 8 : 16 with brick ballast 40mm Nominal size in foundation and plinth. (HSR 10.26)

Cement concrete 1 : 6 : 12 with stone aggregate 40 mm Nominal size in foundation and plinth. (HSR 10.32)

Cement concrete 1 : 4 : 8 with stone aggregate 40mm Nominal size in foundation and plinth. (HSR 10.39)

Cement concrete 1: 2 : 4 with stone aggregate 20mm nominal size in foundation and plinth. (HSR 10.41)

Cement concrete 1:2:4 with stone aggregate 20mm nominal size for reinforced concrete work in shelves excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respect. (HSR 10.81)

Cement concrete 1:1.5:3 with stone aggregate 20mm nominal size for reinforced concrete work in shelves excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respect. (HSR 10.81 + 10.95 a)

Cement concrete 1:1.5:3 with stone aggregate 20mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respect. (HSR 10.82 +10.95 a) (a) 1st Storey

2nd Storey

First class brick work laid in cement sand mortar 1:6 in foundation and plinth. (HSR 11.2)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level. (HSR 11.7) (a) 1st Storey.

2nd Storey.

First class brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level. (HSR 11.9) (a) 1st Storey.

2nd Storey.

Extra for brick work in Square or rectangular Pillars in buildings. (HSR 11.42) (a) 1st Storey.

2nd Storey.

Terracing consisting of tiles 22.86cm x 11.43cm x 3.81cm, laid over 87.50mm mud filling on a layer of 25mm mud plaster and another layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 Kg per Sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13) (a) 1st Storey.

2nd Storey.

Corrugate G.I sheet roofing 0.80mm thick fixed with galvanized iron ‘J’ or ‘L’ hooks, 10mm dia G.I limpet and bitumen washers complete, excluding the cost of purlins,rafters and trusses. (HSR 13.18)

Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16. (HSR 13.50)

Cement concrete 1:2:4 gola 10cm x 10cm quardrant along junction of roof with parapet wall finished smooth, where specially specified. (HSR 13.64)

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (a) 100mm dia PVC pipe 6 kg. pressure (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. (HSR 13.89 a) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing and fixing PVC Bend ISI mark. (a) 100 mm dia PVC Bend (Note:- Reputed make PVC Bend such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. (HSR 13.90 a) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Base course of floors consisting of 100mm thick cement concrete 1:8:16 and 100mm sand or stone filling. (HSR 14.1)

Fixing Marble stone flooring 17mm and above thick slab including matching grains of marble laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of marble including rubbing and polishing (Marble shall be supplied by the department). (HSR 14.49)

Kotah Stone flooring, minimum 25mm thick, in any pattern as specified over 20mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing. (HSR 14.62) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Kotah stone 20 mm thick in skirting risers of steps, dados and wall facing (lining) and pillars laid on 12 mm thick cement coarse sand plaster 1:3 laid and jointed with neat cement slurry, mixed with pigment to match the shade of stone including rubbing and polishing including labour for fixing cramps, dowels and pins etc. (HSR 14.66) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & fixing Vitrified Tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note: - Tile shall be premium quality (1st quality) of reputed manufacturer like NITCO, SIMPOLO, ORIENTBELL, KAJARIA & RAK. (NS) Note:- The Agency to whom the work is allotted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic Glazed Tiles 300 x 450mm. of reputed manufacturer like: - RAK, NITCO, KAJARIA, SIMPOLO, ORIENTBELL shall be used as approved by Engineer-in-charge. (HSR 14.92 b) Note: - The agency to whom the work is allotted will have to produce original bill/ voucher for all quantity in token of proof of purchase of material.

10mm thick cement plaster 1:3 (HSR 15.2) (a) 1st Storey

2ns Storey

12mm thick cement plaster 1:6. (HSR 15.7)

15mm thick cement plaster 1:6 on the rough side of single of half brick wall. (HSR 15.12)

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. (HSR 16.1)

Painting two coats with synthetic enamel Paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.5)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (b) 1st Quality. (HSR 16.79 b)

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81)

Chowkats of commercial hard wood such as hillock, champ, chikrassy, and chaplash, etc., (Non-coniferous timber other than teak conforming to I.S. specification no. 1003 kiln seasoned), of doors and windows including iron hold fasts, corner straps, screws, bolts for hold fasts, etc., complete fixed in positon. (HSR 17.12)

Factory manufactured panelled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc (Non coniferous timber other than teak confirming to IS specification No. 1003, Kiln seasoned), with 100mm wide verticle styles, 150mm wide lock rail, 200mm wide bottom rail and 100mm wide other rails, with panels of 12mm thick commercial veneered both sides particle board or plywood of BWR grade, hot pressed, including cost of iron hings, screws, chocks/cleats, stops and nails etc, complete fixed in position (excluding the cost of any fittings, other than specified above but including labour for fixing the same in position. (b) 35mm thick. (HSR 17.91 (b) - Note 17.18 i)

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. (non coniferous timber other teak, conforming to IS specification No. 1003, kiln seasoned) with 100mm wide vertical styles 150mm wide lock rail 200mm wide bottom rail and wire gauze of 140G or 120G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) (styler and rails of windows shutters shall be 75mm wide). (b) 35mm thick. (HSR 17.92 (b) - Note 17.18 i)

Factory manufactured solid flush door shutters, with block board core as per IS 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot pressed, confirming to IS 2202 part I and II, fixed in position, including iron hinges, screws, chocks/ cleats and stops, etc (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (a) commercial veneering with vertical grains or corss bands and face veneer on both sides commercial facing with laminated core and lipped edges:- (iii) 35mm thick. (HSR 17.93 (a) (iii) - Note 17.18 i)

30mm thick.

25mm thick.

Fixed portion (Anodised aluminium transparent or dyed to required shade according to IS; 1868, minium anodic coating of grade AC 15) Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make confirming to IS; 733 and IS; 1285fixed with rawplugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required neoprene felt etc. aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ panelling C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing and panelling to be paid for separately). (HSR 17.95)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board confirming to IS; 12823 grade 1 type II in panelling fixed in aluminium doors. Windows shutters and partition frames with C.P. brass/ stainless steel screws etc. complete. (b) Pre-laminated particle board with decorative lamination on both sides. (HSR 17.97 (b)

Providing and fixing glazing in aluminium door, windows, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete (cost of aluminium snap beading shall be paid in basic items. (b) with float glass panes of 5.00mm thickness.(HSR 17.98 (b)

Supplying and fixing glass panes including special metal sash putty of approved make. (b) Glass panes 4 mm thick, exceeding 40sq dm areas. (HSR 18.30 b)

Pressed steel sheet frames (chowkats), consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:3:6 for lugs complete:- (d) door and window frame of size 114mm x 50mm with 35mm wide double rebate. (HSR 18.34 d)

N.S. items

Earth work non plastic Tibba Sand with an taken from outside of campus area with all lead and lift including loading, unloading, laid in 15cm layer including ramming, watering, consolidating, compaction, and compensation of earth etc., complete in all respect as per the direction of engineer in charge. (NS) Lead 5:00 KM

P/F acoustical wall panelling with finished face of 3.5-4mm (AP/EP Series of GARNET or Equivalent) veneer. The veneer shall be pasted on 12mm thk WPS Hybrid Board (ALSTONE or equivalent) using adhesive, necessary headless nails, screws, etc. The ply shall be fixed on G.I framework (Make -Gypsteel / India Gypsum or gabson) Comprising of 48mm studs (0.55mm thick having one flange of 34mm and another flange of 36mm made of GI steel) placed at 600mm centre to centre both ways (maximum or less wherever required) in 50mm floor and ceiling channel (0.55mm thick having equal flanges of 32mm made of GI Steel) in desirable profile (Straight or Curved). A layer of 50mm thk. glass wool, density 24kg/cum, (make UP twinga/Owen cornil) wrapped in acoustical tissue shall be provided. The veneer shall be polished with MRF melamine sealer followed by two coats of melamine (matt polish Asian make) with the help of compressor. Complete in all respect with the entire satisfaction of the Engineer-in-Charge. (NS)

Providing & fixing 4.0mm DND Skylight fiber glass Sheet UV Stablized Material shed with frame work with M.S. Pipe 11/2" x 11/2" (2.9mm) gauge welding job work with Asian Paint & Primer and canono Fasrner i/c filing of fiber glass sheet (Pop Ripit) and water proofing (G.E. Silicon sealent) complete in all respect as per approval of the Engineer-in-Charge of the work. (NS)

Fe-500 EQR TMT steel bars for RCC works where not including in the complete rate of RCC including bending, binding and placing in position complete. (NS) Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. From the length so measured, the weight of reinforcement shall be calculated in tones on the basis of IS:1732.Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.

Providing and fixing gate of stainless steel 304 grade pipes including machenism for motorized movement complete as per design and drawing complete in all respect as per approval of the Engineer-in-Charge of the work. (NS)

Provision for fixing of stainless steel "alphabets letters" for College name upto 0.6 mtr. height and 0.04 mtr. wide and deep approximate 33 letters complete in all respect as per approval of the Engineer-in-Charge of the work. (NS)

Providing and fixing aluminum composite panel 4mm thick (0.5mm + 3mm + 0.5mm), PVDF of approved make of AL-STRONG make including aluminum section complete in all respect to the entire satisfaction of Engineer-in-charge. (NS)

Provision & fixing of Cat eyes Granite stone 15 to 18mm thick in skirting/ dado, riser of steps, pillars and wall facing, laid in any pattern as specified over base of 12mm thick cement coarse sand mortar complete in all respect as per approval of the Engineer-in-Charge of the work. (NS)

P.H. work

Cutting holes upto 23cm square for pipes in floor and roofs of cement concrete reinforced concrete or reinforced brick work and making good including repointing, replastering, replacing bitumen and colour or white washing where required. (e) 225mm thickness of floor or roof. (HSR 28.26 e)

Constructing brick masonry inspection chamber sizes as given below upto 0.60 meters average depth in cement mortar 1:5 lime concrete with 40 percent lime mortar 2:3 in foundation cement concrete 1:2:4 benching 12mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement RCC 1:2:4 slab 100mm thick/C.C. topping 50mm thick with 455mm x 455mm / 455mm x 610mm inside light duty C.I inspection chamber cover and frame weight as per I.S.I specification painted with 3 coats of black bitumastic superior paint complete as per standard design. (a) Size 450mm x 450mm inside (with 455mm x 455mm cover and frame light duty single seal weighing 40 kg with C.C. topping). (HSR 29.84 (a)

Providing and fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian type Orissa or Orya water closet suite for Sinking into floor, with raised foot treads complete with 100mm H.C.I, ‘P’ Trap with or without vent as required and all other necessary fittings as fully described in item no.30.1 above. (b) Size 630mm. (i) White. (HSR 30.2 (b) (i)

Providing and fixing in position best Indian make (to the approval of Engineer-in-charge) European type water Closet Suit with Non-Concealed ‘P’ or ‘S’ Trap with or without vent and all other necessary fittings as fully described in item no. 30.3 above. (i) White. (HSR 30.4 (i)

Providing and fixing in position best Indian make flat black or angular lipped front urinal 465mm high consisting of:- (i) Flat black lipped or angular urinal basin of Vitreous China ware (to the approval of the Engineer-in-charge). (ii) 5 Litres capacity mosquito proof Indian make C.I. automatic flushing cistern painted with non-yellowing white enamel paint or other approved shade enamel paint on outside and superior black bitu-mastic paint on inside complete with screwed 15mm pipe; (iii) Pair of R.S. or C.I. painted brakcets and pair of R.S. or C.I. painted brakcets and brass couplings. (iv) Standard size G.I. flush pipe with C.P brass wall clips and unions complete including cutting and making good the walls and floor and painting of fittings etc. (as Required by the Engineer-in-charge). (i) White. (HSR 30.19 (i)

Providing and fixing in position Indian make (Ordinary) Lavatory Suites Consisting of Lavatory in Vitreous China Ware size as given Below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary; R.S or C.I Brackets for building into wall including Painting; 32mm C.P Brass Waster with C.P brass chain and rubber plug; 15mm C.P Brass Screw down pillar tap with Jamnuts or couplings best design (as approved by the Engineer- In-charge). All fittings best Indian make and to the approval of the Engineer-in-charge. All brass work chromium plated and complete in all respects including cutting and making good the walls floors and painting of fittings etc. (a) White. (i) Size 450mm x 300mm with one no. Tap. (HSR 30.41 (a) (i)

Providing and fixing in position of best quality Stainless Steel Sink with complete fittings as fully described in item no. 30.51 above. (a) 600 mm x 450 mm x 200 mm. (HSR 30.53 (a)

Providing and fixing in position best Indian make bevelled edge 5.5mm thick Mirror mounted on Asbestos sheet ground fixed in position by means of 4 Nos. chormium plated brass screws and washers over rubber washers and rawl plug embedded in the wall or chromium plated brass clamps with C.P brass screws (as required by the Engineer-in-charge) complete including cutting and making good the walls etc. (a) Indian make. (ii) 550mm x 400mm. (HSR 30.71 (a) (ii)

Providing and fixing in position 15mm i/d C.P brass bib Cocks of best quality (as required by the Engineer-in-charge. (c) Bib cock. (HSR 30.75 c)

Bib cock long body.

Providing and fixing in position automatic brass ball valves in tanks. (b) With Plastic Ball. (ii) 20mm internal diameter. (HSR 30.110 (b) (ii)

Providing and fixing HDPE Water Storage Tanks of Sintex, Diplast, O.K. make with covers/ lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respect to the satisfaction of Engineer-in-Charge. (except civil work). (e) 1000 Ltr. Capacity. (HSR 30.119 e)

500 Ltr. Capacity.

PH N.S. items

Providing & fixing of PVC seat cover "BKC make" complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of C.P. Zet set complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of mirror 16" x 20" with wooden frame complete in all respect as per approval of the Engineer-in- charge of the work. (NS)

Providing & fixing of P-trap Supreme make complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing for laying, jointing, fixing and testing G.I. (Medium class "B" type of Tata & Jindal make) pipe lines and specials tees bends, sockets, elbows etc. inside building and testing etc. complete including cutting threading. Including cost of Special. G.I. specials shall be of Make:- UNIK, TATA, ZOLOTO. (b) 20mm i/d. (NS)

Providing & fixing of ball valve 20mm dia complete in all respect as per approval of the Engineer-in-charge of the work.. (NS)

Providing & fixing of waste pipe "PVC" complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of PVC connection 18" complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of 15mm dia angle valve complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of PVC Cistern 10Ltr. Capacity complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of Pillar cock "BKC make" complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of wash hand basin 16" x 20" of "Hindware make" oval type complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing, fixing and jointing union couplings in G.I. and W.I. pipelines. (NS)

Providing & fixing of Shower Ultra thin 6" complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of waste jali complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of ball cock 15mm dia complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of 1HP sumersibal pump set "make Kriloskar, Sharp, Crompten" complete in all respect as per approva of the Engnieer-in-Charge of the work. (NS)