ROOF SHEET BRICK WORK TILING PLINTH PROTECTION AND COMPREHENSIVE MAINTENANCE REPAIR REPLACEMENT OF CENTRAL PACKAGE TYPE AC PLANTS UNDER GE I GOS

Amount

Dismantling of AC/GI plain/Corrugated / semi corrugated roof sheets any type and any size complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and as directed by Engineer-in-Charge.

S&F Mild steel work in tubular poles & trusses (framed) including purlins,rafters and special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS-1161-1979 grade St-240 complete all as specified and as directed by Engineer-in-Charge.

S & F steel Fe-410-W (Gde 250 Quality-A) work in tubular stanchion/post including special shaped washer etc. complete using one of more tubes or induction butt welded tubes conforming to IS-1161- 1979 grade St.-240 complete all as specified and directed.

S&F mild steel work Fe-410-W (Gde 250 Quality-A) in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete all as specified and as directed by Engineer-in-Charge.

M&L for MS Framed work of Fe 410 W (Gde-E-250) Quality A, as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

M&L 75 mm thick PCC 1:3:6, type C-1 using 20 mm graded stone aggregate as in plinth protection, surfaces finished even and smooth with out using extra cement all as specified.(Note- Joint 12 mm wide to the full depth of pcc shall be provided at every 3 metres and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. cost of this provision shall be deemed to be included in the quated rate for concrete in plinth protection

Taking down chowkhat or frames n exc 1.50 Sqm each with shutters (without taking off shutters from the frame) and removing to or from store complete all as specified and directed

Taking down chowkhat or frames exc 1.50 Sqm and n exc 4 Sqm each with shutters (without taking off shutters from the frame) and removing to or from store complete all as specified and directed

Taking down shutter of any description area not exc.1 sqm each and removing to or from store complete all as specified and directed.

Taking down shutter of any description area exc. 1 sqm but n exc 2 sqm each and removing to or from store complete all as specified and directed.

Taking down and Refixing of shutter of any description not exc 1 sqm each leaf in same opening after easing and adjusting building hard ware etc complete all as specified and directed

Taking down and Refixing of shutter of any description exc. 1 sqm but not exc 2 Sqm each leaf in same opening after easing and adjusting building hard ware etc complete all as specified and directed

S&F Second class hard wood (Sal) plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F Second class hard wood 30 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass,gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,gauze etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (a) complete all as specified and directed.

S&F Second class hard wood 30 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass,gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,gauze etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (b) complete all as specified and directed.

S & F 35 mm thick second class hard wood rail and style plain, framed, factory made panelled shutters (Two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and stiles are as per IS – 1003 (Part – I), kiln seasoned & chemically pressure treated complete all as specified and directed.

S & F for solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2010 Part-II complete all as specified and directed

S & F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S & F in the frame as per specifications and shown on drawing in section 8 of SSR-2010 Part-II complete all as specified and directed

M&L in repair 12 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work incl taking down old cupboards etc. complete all as specified and directed.

S&F 6 mm thick teak wood liping 12 mm width prelaminated particle board fixed with screws complete all as specified and directed.

S & F in repair Continuous (piano) hinges, 40 mm width of mild steel, bright finish or electrogalvanisd complete all as specified and directed.

S&F in repaur Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F 2nd class hardwood Beads, straight (any size) for glazed or gauzed joinery, renewed, including mitres etc., and removing old beads to Store

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4 mm fixed with stainless steel wire staples or with necessary beads complete all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4 mm fixed with stainless steel wire staples or with necessary beads complete all as specified and directed.

M&L Mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings,frame work of watertanks and similar work conforming to Fe -290 Gde E-165 complete all as specified and directed.

S&F in repair 100 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised type B-21 complete all as specified and directed.

S&F in repair 75 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised type C-21 complete all as specified and directed.

S&F in repair 150 mm size extruded aluminium alloy handles fabricated type anodised of complete all as specified and directed.

S&F in repair 100 mm size extruded aluminium alloy handles fabricated type anodised of complete all as specified and directed.

S&F in repair 150 mm long aluminium,anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F in repair 100 mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F in repair 250 mm long aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 150 mm complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

Hacking out old broken glass (any thickness, size quality or description) form wooden frames or steel,Alu, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F in repair 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Taking down aluminium door and windows/ventilator of any size and of any description built in wall and making good at disturbed surface with cement mortar 1:4 and applying two coats of plastic emulsion paint as per existing treatment complete all as specified & directed.

S&F Powder coated Aluminium anodised glazed side hung door shutters with anodised aluminium frame of section of 100x44x2mm and bottom rail of 44.5x99x1.8mm including 5.5mm thick tinted sheet glass ordinary quality with all necessary suitable push & pull plate/handle , screw, jointing cleats, rubber packing aluminium snap beading and 1 No 200mm long Aluminium tower bolt, 100mm long 3 No Aluminium butt hinges B-21 Type and one No mortice brass lock 100 size 4 leaver (Vertical Type) with 01 No door closer Aluminium (Diie cast) body hydraullically regulated designation ;No 02 universal type, for each shutters complete all as specified; and ;directed

S&F Powder coated three track Aluminium sliding window with frame not less than 1.8 mm thick including 4 mm thick tinted glass, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket, aluminium snap beading & necessary rubber packing, locking, roller & opening arrangement, incl Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm, all fitting and fixtures complete all as specified and directed by Engr-In-Charge

S&F Powder coated Aluminium Ventilator with frame not less than 1.8 mm thick & including 4 mm thick tinted glass including beading & necessary rubber packing, locking & opening arrangement if required, all fitting and fixture complete all as specified and directed.

S&F 6 mm thick aluminium grills of god quality surrounded by aluminium 'C' channel with mesh size 75 X 75mm incl taking down old grills of any type complete all as specified and directed.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed.

S&F in repair door closer hydraulically regulated designation No 2, universal type, suitable for door shutter of weight not more than 60 Kg of aluminium (extruded section body) complete all as specified and directed.

S&F in repair MS pipe 50 to 125 mm dia as shaft including two coats of aluminum paint over a coat red oxide primer complete all as specifed & directed.

S&F in repair part of steel rolling shutters MS gear box set general complete incl handle and anchoring rod as of approved quality all as specified and directed.

S&F in repair Ball bearing suitable for rolling shutter complete all as specified and directed.

S&F in repair Guide channel 3" (3.50 mm thick) mild steel deep channel section etc.complete all as specified and directed.

S&F in repair Hood Cover made of 1 mm thick GI Sheet pattern

S&F in repair Bottom plate 5" (2.25mm) complete all as specified and directed.

S&F in repair Anchoring rod of 25 mm dia of MS pipe complete all as specified and directed.

S&F in repair Safety lever locks MS with 4 levers complete all as specified and directed.

Taking down and refixing in the same opening steel rolling shutter including oiling and greasing to required necessary fitting to functionall shutters as required bush, Spring. MS pipe , rod .lock. ball bearing, top cover, anchoring rod, hasp and staple and push pull or gear operating system , bevel gear box and crank handle etc complete all as specified.and directed.(area of rolling shutters exc 6 sqm but n. exc. 18 Sqm each ) (Note:- Necessary constituent items required during repair of rolling shutter shall be paid seperately as given above .)

S & F in 1.00 mm thick mild steel rolling shutter strips duly pressed on both ends of vertical sides for interlocking locks for the required length of existing shutter as directed by Engg-in-Charge

M&L for preparation of new or previously untreated surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L preparation of old decorated Steel painted surfaces of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Demolition of brick work built in cement mortar including all quions, arches, pillars etc all as specified and directed

M & L for brick work with sub class "B" brick (old size) straight or curved on plan to any radius in half brick thick walls built in CM 1:4 to any radius complete all as specified and directed.

M & L for brick work with fly ash bricks straight or curved on plan exc 6m mean radius in CM 1:4 including demolition of brick work or stone/ boulder masonry, built in cement mortar completed all as specified and directed.

M&L for rendering 10 mm thick on other than fair face of brick works in CM 1:6 and to be finished even and smooth with out using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth with out using extra cement and mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed. (Note: supply only of WPC shall be measured and paid for seperately)

M&L for preparation of new decorated surfaces of walls and apply one coat of white wash complete all as specified and directed

Taking down UPVC door and windows/ventilator of any size and of any description built in wall and making good at disturbed surface with cement mortar 1:4 complete all as specified & directed.

M&L for preparation of new plastered surfaces of walls and applying one coat of oil bound distemper complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off premises complete all as specified and directed

M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment.

M & L coloured vitrified tiles Light shade 10 mm thick (square/rectangular) polish area of each tiles n exc 0.36 Sqm coloured cut to required size set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles as in floor incl 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M & L coloured vitrified tiles 10 mm thick (square/rectangular)polish area of each tiles n exc 0.36 Sqm coloured cut to required size set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles but in vertical surfaces incl 10 mm thick rendering in CM 1:3 complete all as specified and directed.

M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S & F in repair Toilet Paper Holder with Flap complete all as specified and directed. Make-Jaquar AKP-3573P

S&F in repair single door PVC cabinet mirror of size 300 mm x 450 mm with internal shelves all as specified and directed.

S & F in repair sheet Glass Shelf assembly consisting of 5.5 mm glass sheet shelf 12 cm wide with cromium plated bracket guard and railing 60 cm long complete all as specified and directed..

Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade (ISI marked) with all fittings fixed complete to walls, ceilings or laid in floors of 15 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade (ISI marked) with all fittings fixed complete to walls, ceilings or laid in floors of 20 mm bore of pipe complete all as specified and directed.

S & F 15 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified

S & F 20 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified

Making connection of PPR distrubtion bracnch with PPR main of following outer dia of pipe 16 to 40mm size by providing and fixing tee including cutting and making fusion joint etc

Refixing old steel tubing and connections in new or old position (wall, floor, ceiling etc) of 15 mm bore of pipe complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (wall, floor, ceiling etc) of 20 mm bore of pipe complete all as specified and directed.

S&F in repair Bib taps fancy type chromium plated 15 mm dia, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

Taking down bib tap /wash basin tap/pillar tap/stop cock/mixture tap and refixing the same after repair and replacement of washer only for 15 mm bore size without replacing spindles complete all as specified and directed.

Taking down bib tap /wash basin tap/pillar tap/stop cock/mixture tap and refixing the same after repair and replacement of spindles for 15 mm bore size complete all as specified and directed.

S & F in repair Brass chromium plated wall mixer non-telephonic shower arrangement with connecting legs & wall flanges for 15 mm bore of pipe all as specified and directed.

S & F in repair Brass chromium plated hole bidet mixer (Basin mixer) with pop-up waste system with 300 mm long braided hoses complete all as specified and directed.

S & F in repair Brass chromium plated Sink mixer with raised J shaped swinging spout (Wall mounted model) with connecting legs & Wall flanges complete all as specified and directed.

S&F in repair Chromium plated fancy type Stop valves 15 mm, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair, 15 mm bore stop cock, cast copper alloy with long shank and cup (concealed type) fancy type chromium plated screwed down high pressure with crutch & butterfly handle screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair pillar tap cast copper alloy with capstan head chromium plated crewed down high pressure with or without lettered hot or cold with long screwed sharks and ply nuts 15 mm dia complete all as specified and directed.

S & F in repair bottle trap chromium plated for WHB as per approved quality all as per specified and directed.

S&F in repair PVC waste pipe for WHB etc all as specified and directed.

S&F in repairs 32 mm bore dia waste coupling of (min weight 32 mm-45 gm of PTMT) (half or full threaded) etc complete all as specified and directed

S&F in repair CP grating 100 mm dia with waste hole (minimum weight 40 gm) complete all as specified and directed

S & F in repair CP Jet spray for 15 mm bore all as specified and directed.

S & F in repairs Hand shower (Health faucet) with 1 mtr long Easy flex tube in crome finish & wall hook Complete all as specified and directed.

M&L in repairs for vitreous china wash basin, white,flat back, size 550 x 400 mm including supply & fixing of brass chromium plated coupling 32 mm etc complete all as specified and directed.

M&L in repair Wash down water closet vitreous china white pedestal pattern with 'P' or 'S' trap including connecting to outgoing drain pipe & to flushing pipe excluding flushing cistern and flush pipe complete all as specified and directed.

S&F in repairs plastic water closet seat cover, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S & F in repair Kitchen sink made of stainless steel 1 mm thick with plug washer and waste pipe incl bedding fixing cantilever brackets and connetction union to pipe overall size 915 X 460mm bowl size 405X 355 mm complete all as specified and directed

S& F in repair 1 mm thick stainless steel plate rack of size 900X900X200 incl fixing with rawal plug and screws complete all as specified and directed.

S & F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 500 litre capacity hoisted and fixed in position including dismantling of old u/s water tank and removing to store complete all as specified and directed

S & F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 1000 litre capacity hoisted and fixed in position including dismantling of old u/s water tank and removing to store complete all as specified and directed

S&F ball valves for 20 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed.

S&F ball valves for 25 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 455 gms) complete all as specified and directed.

S&F in repairs ball valves for 20 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed.

S&F in repairs ball valves for 25 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 455 gms) complete all as specified and directed.

S & F in repair PVC Tank cover for 500 Ltr capacity fixed in position with nuts and bolt complete all as specified and directed

S & F in repair PVC Tank cover for 1000 Ltr capacity fixed in position with nuts and bolt complete all as specified and directed

S&F in repairs, PVC valveless syphonic action type low level flushing cistern, 10 ltrs capacity with inlet, ball valve, float and handle including bracket complete all as specified and directed

S & F in repair internal fitting for low level flushing cistern (Syphon) complete all as specified and directed.

S&F in repairs flush pipe 32 mm dia of polyethylene of low or high density or PVC, for low level cistern complete all as specified and directed.

S & F in repair 125 mm dia chromium plated shower rose of with or without swivel joint incl fixing to steel pipe complete all as specified and directed.

S&F in repair PVC connection 15 mm bore, 450 mm long complete with both ends unions complete all as specified and directed.

S&F in repairs CP anodised tubular tower rail, 20 mm dia, D type, 60 cm long between flanges etc.

S & F in repair 75 mm PVC(SWR) floor trap with grating incl jointing with solvent cement complete all as specified and directed

S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe of 20 mm bore dia of pipe complete all as specified and directed.

S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends (ISI marked) for iron pipe of 25 mm bore dia of pipe complete all as specified and directed.

S & F in repair Soap dish any type fixed to plug with chromoium plated brass screw complete all as specified and directed.

S & F in repair corner glass shelf with brackets complete all as specified and directed.

S & F in repair Europian WC floor mounted cascade pattern vitreous china with dual core flushing cistern incl all fitting flush pipe etc make Hindware cat 92048 (starwhite) or equivalent of specified make complete all as specified and directed.

S&F in repairs door seal with aluminium beading and 50 mm wide rubber seal complete fixed to aluminium/ Wooden doors complete all as specified and directed.

S & F in repairs Magic Eyes for door eye viewers brass body complete all as specified and directed.

S&F in repairs Stainless Steel Towel Rack 600 mm long with Lower Hangers but with 3 hooks.

S & F repair Over head Shower 100 mm round shape single flow (ABS body chrome plated with gray face plate ) with rubit cleaning system complete all as specified and directed.

S & F in repair chromium plated towel ring with bracket complete all as specified and directed.

S & F in repair hasp and stapple safety type aluminium anodised 75 mm long with mild steel hinge pin including bolt to hinge plate fixed with screw complete all as specified and directed.

S&F in repairs 15 mm dia Curtain rods, mild steel, chromium plated with fixing brackets complete all as specified and directed.

M&L for preparation of old surface by scraping and smoothing the surface with water emery paper and painting with approved colour of synthetic enemelled paint of two coat over a coat of primer red oxide and writing letters/numbers(SM/MES Nos.) of Compressor with motor, foundation frame, including foundation of A/c plants of capacities 30 to 33 TR and cleaning the surrounding area up to three metre out side area of the plant by cutting grasses and surface dressing including white wash of plantroom complete all as specified and directed by Engineer in charge.(Note: The arrangement of men power,T&P and necessary items shall be contractors responsibility)

All as per item No 139 above but Condenser assembly of AC plant of capacity 30 to 33 TR.

All as per item No 139 above but Condenser water pump with motor, foundation frame and including foundations, rubber washers,glands, nuts, bolts and washers of AC plant of capacity 30 to 33 TR

All as per item No 139 above but exposed water circulation and gas circulations pipe lines including marking direction of flow of AC plant of capacity 30 to 33 TR.

All as per item No 139 above but Cooling tower cleaning with proper cleaning agents twise in the contract period without any damages in cooling towers complete of AC plant of capacity 30 to 33 TR

All as per item No. 139 above but for 22/30 TR capacity A/C plant complete all as specified and directed as Compressor with motor, foundation frame including foundation.

All as per item No 01 above but Condenser assembly of AC plant of capacity 22/30 TR.

All as per item No 01 above but Condenser water pump with motor, foundation frame and including foundation rubber washers,glands, nuts, bolts and washers of AC plant of capacity 22/30 TR.

All as per item No 139 above but Exposed water circulations and gas circulates pipe lines including marking direction of flow of AC plant of capacity 22/30 TR.

All as per item No 139 above but Cooling tower complete of AC plant of capacity 22/30 TR.

M&L for replacement of cast iron sluice valve with stainless steel spindles with flanged ends duly ISI marked confirming to IS 780 part1, PN 1 type complete suitable as per exiting AC plant for the 100 MM bore sizes complete all as specified and directed. :- Make: Kirloskar /RMCO / Upadhiya

All as per item No 149 above but 80 MM bore

All as per item No 149 above but 65 MM bore

Taking down old unsv butterfly valve from existing location and supply and fixing new butterfly valve of size 100 mm dia and including necessary pipe fittings nuts,bolts,washers and rubber washers etc complete all as specified and directed Make:- Kirloskar/L&T/Amco industrial valves/RMCO/Upadhiya

All as per item No.152 above but size 80 mm dia.

All as per item No.152 above but size 65 mm dia.

All as per item No.152 above but size 50 mm dia.

Taking down old unsv Non return valve from existing location and supply and fixing new non return valve of size 100 mm dia and including necessary pipe fittings, nuts,bolts,washers and rubber washers etc complete all as specified and directed Make:- Kirloskar/L&T/Amco industrial valves/RMCO/Upadhiya

All as per item No.156 above but size 80 mm dia.

All as per item No.156 above but size 65 mm dia.

All as per item No.156 above but size 50 mm dia.

Taking down old unsv Non return butterfly valve from existing location and supply and fixing new non return butterfly valve valve of size 100 mm dia and including necessary pipe fittings, nuts,bolts,washers and rubber washers etc complete all as specified and directed Make:- Kirloskar/L&T/Amco industrial valves/RMCO/Upadhiya

All as per item No.160 above but size 80 mm dia.

All as per item No.160 above but size 65 mm dia.

All as per item No.160 above but size 50 mm dia.

Taking down old unsv pipe line from existing loaction and supply and fixing new MS ERW heavy duty pipe of size 100 mm dia with fittinmgs and including providing necessary fabrication,welding work and accessories nuts,bolts and washers complete all as specified and directed.

All as per item No.164 above but size 80 mm dia.

All as per item No.164 above but size 65 mm dia.

All as per item No.164 above but size 50 mm dia.

Taking down old unsv pipe line from existing loaction and supply and fixing new GI heavy duty pipe of size 100 mm dia with fittings and including providing necessary fabrication,welding work and accessories nuts,bolts and washers complete all as specified and directed.

All as per item No. 168 above but size 80 mm dia.

All as per item No.168 above but size 65 mm dia.

All as per item No.168 above but size 50 mm dia.

All as per item No.168 above but size 40 mm dia.

All as per item No. 168 above but size 32 mm dia.

All as per item No.168 above but size 25 mm dia.

Taking down old unsv gate valves from existing loaction and supply and fixing new gate valve of size 100 mm dia with necessary accessories nuts,bolts and washers complete all as specified and directed.

All as per item No.175 above but size 80 mm dia.

All as per item No.175 above but size 65 mm dia.

All as per item No.175 above but size 50 mm dia.

All as per item No.175 above but size 25 mm dia.

Taking down old unsv strainer for suction from existing loaction and supply and fixing new strainer of size 150 mm dia with necessary accessories nuts,bolts and washers complete all as specified and directed.

All as per item No.180 above but size 100mm dia.

M&L for Dismantling and removing defective fins of FRP type cooling tower and supply and fixing new PVC fins brick containing suitable for existing cooling tower system, eleven layers size of brick 600 mm x 300 mm x 150 mm complete all as specified and directed.

M&L for dismantling and removal of old unserviceable motor and Supply and fixing in replacement of cooling tower fan motor(induction motor) of capacity 3 HP, 415 V as per site conditions/suitable and incl providing necessary shaft key,shaft,nuts,bolts and wahsers complete all as specified and directed. Note- Old u/s motor to be deposite in AGE E/M store.(Note: The arrangement of men power,T&P, settings shall be contractors responsibility)

M&L for dismantling and removal of old unserviceable motor and Supply and fixing in replacement of cooling tower fan motor(induction motor) of capacity 5 HP, 415 V as per site conditions/suitable and incl providing necessary shaft key,shaft,nuts,bolts and wahsers complete all as specified and directed. Note- Old u/s motor to be deposite in AGE E/M store.(Note: The arrangement of men power,T&P, settings shall be contractors responsibility)

Opening of shell and tube condensor end covers for inspection, pressure testing for leakage detection of condensor and identification of leakage, arresting the same with brazing, pressure testing after repairs, reassembling of end covers including cost of rubber gasket and making water connections, testing and commissioning to the entire satisfaction of Engineer-in-charge complete all as specified. (Note: The arrangement of men power,T&P, Nitrogen gas,welding eqpts shall be contractors responsibility)

M&L for dismantling and removal of old unserviceable chilled water tank and S & F in replacement of chilled water storage tank stainless steel with installation for AC plant as per existing size and specification complete all as specified and directed.

M&L for dismantling and refixing after proper alignment with & including providing new belt,nut bolt and fixing accessories for fan & motor of cooling tower of AC plant complete all as specified and directed.

S&F in replacement blower shaft both end bearing with casing self revolving type NTN P-207 as per existing complete all as specified and directed by EIC

Supply and fixing in replacement cooling tower fan with hub as per sample of existing size as directed by Enigneer-in-charge.

M&L for dismantling and removal of old unserviceable motor and S & F in replacement of blower motor of capacity 20 HP, 415 V with installation for AC plant as per existing specification and conditions complete all as specified and directed. Note- Old u/s motor to be deposite in AGE E/M store.

Supply and charging refrigerant gas R-22 complete all as specified and directed. Make: Mafron

Taking out / purging of refrigerant gas from the system of A/c plant 1 x 30/33 TR capacity carrying out vacuum test by vacuuming the whole A/c plant with the help of vacuum pump and checking the complete system for leakages. Carrying out the pressure test by charging the nitrogen gas in the system and checking of any leakage point , repair / rectification of the same and removing the nitrogen gas from the system and charging of refrigerant gas including charging of additional gas as required and complete all as specified and directed. (Note: The arrangement of men power,T&P and Nitrogen gas shall be contractors responsibility)

All as per item No. 55 above for 1 x 12.5/22 TR unit of A/c plant, complete all as specified and directed.

S & F in repairs thermostat expansion valve suitable for 12.5 to 33 TR complete all as specified and directed. (Make: Sporlan / Alco)

S & F in repairs water temparature sensor suitable for 12.5 to 33 TR complete all as specified and directed. (Make: as per existing model and make or suitable any other approval )

M&L for dismantling and removal of old unserviceable condensor coil and S&F in replacement condensor coil for 5.5 TR capacity condensor as per existing site requirement for package type AC plant complete all as specified and directed.

Supply and fixing in replacement of liquid line stainer filter for SMC-6-65/SMC-4-100 complete all as specified and directed.

Supply and charging of compressor oil complete all as specified and directed.

M&L for dismantling and removal of old unserviceable motor with pump and S&F in replacement monoblock pump motor of capacity 10 HP, 415 V as per site requirement and conditions for AC plant complete all as specified and directed and Old u/s pump motor to be deposite in AGE E/M store. (Note: The arrangement of men power,T&P, settings shall be contractors responsibility)

M&L for descaling of the entire water circulating system for central AC plant water cooled of capacity upto 3 x 33 TR along with condensers, cooling tower/piping pumps etc. Opening condenser by disconnecting nut bolts and cleaning with MAIC descaling solution with help of descaling pump/wire brush, cleaning rod etc circulating above solution in condenser pipe lines as required time, flushing out the complete solution from condensers pipe line by fresh water with pressure. Re-assembling by replacement of unserviceable nut bolts washers gaskets etc all as specified and directed. Note:- cleaning and descaling shall be carried out by pump with acid as required to keep head pressure within safe limit. If any damage during cleaning/descaling repair shall be carried out by contractor without any extra cost. (Note: The arrangement of men power,T&P, settings by mechanic shall be contractors responsibility)

M&L for clean the filter & cooling coil, gas leakage testing and electrical fault detection of any kind for package type AC plant of capacity 4.5/5 TR complete all as specified and directed.

M&L for clean the filter & cooling coil, gas leakage testing and electrical fault detection of any kind for package type AC plant of capacity 10/13.5 TR complete all as specified and directed.

Checking of air conditioning plant water cooled any size , capacity and location for functioning of motors, condenser , blower fan motors , unusual noise, refrigerant standing pressure and nut bolt washers etc including testing for smooth functioning and inform Engr in Charge for repair if required complete all as directed by Engr-in-charge. (Note: The arrangement of men power,T&P, settings by mechanic shall be contractors responsibility)

S&F in repair fan belt No C-112 complete all as specified and directed, Make- FENNER or equivalent

S&F in repair fan belt No B-86 complete all as specified and directed, Make- FENNER or equivalent

S&F in repair fan belt No B-84 complete all as specified and directed, Make- FENNER or equivalent

S&F in repair fan belt No C-108 complete all as specified and directed, Make- FENNER or equivalent

S&F in repair fan belt No B-66 complete all as specified and directed, Make- FENNER or equivalent

S&F in repair AHU V belt No B-104 complete all as specified and directed, Make- FENNER or equivalent

S&F in repair fan belt No PB82B complete all as specified and directed, Make- FENNER or equivalent

S&F in repair AHU Air filter 20 micron of size 20''x20''x2'' complete all as specified and directed

Dismantling complete ACCEL Compressor set Model SMC-4-65 of 30 TR Cap and overhauling the compressor with repair and checking of wornout holes of studs and providing over size studs with nuts & washers and gaskets . Rematlling and balancing of piston, replacement of piston ring,scrapper ring, split pin, castle nut, connecting rod bolt ,bushing for piston pin, and set of sealing ring of compressor and refitting the same after the repair/replacement duly all as specified and tested for smooth functioning of model SMC-4-100 complete all as specified and directed by Engr-in-charge. (Note-1:The all spare parts are measured and paid separately in relevent items) (Note-2: The arrangement of men power,T&P, settings by mechanic and testing shall be contractors responsibility)

S&F in repair for compressor set Model No SMC-4-65 suction valve ring plate 1.2mm

S&F in repair for compressor set Model No SMC-4-65 Discharge valve ring plate 1.20mm

S&F in repair for compressor set Model No SMC-4-65 Safty valve assembly

S&F in repair for compressor set Model No SMC-4-65 connecting rod bolt

S&F in repair for compressor set Model No SMC-4-65 Castle nut

S&F in repair for compressor set Model No SMC-4-65 Split pin

S&F in repair for compressor set Model No SMC-4-65 Half section of BRG STD

S&F in repair for compressor set Model No SMC-4-65 Bushing with collar STD

S&F in repair for compressor set Model No SMC-4-65 Shaft seal including 10 A-G

S&F in repair for compressor set Model No SMC-4-65 Piston with pin and rings

S&F in repair for compressor set Model No SMC-4-65 Piston ring

S&F in repair for compressor set Model No SMC-4-65 Scrapper ring

S&F in repair for compressor set Model No SMC-4-65 Bushing for piston pin

S&F in repair for compressor set Model No SMC-4-65 Valve spring

S&F in repair for compressor set Model No SMC-4-65 Spring for unloading ring

S&F in repair for compressor set Model No SMC-4-65 Set of Gasket ASL-1453

S&F in repair for compressor set Model No SMC-4-65 Set of sealing ring

S&F in repair for compressor set Model No SMC-4-65 Set of Neoprene O ring

S&F in repair for compressor set Model No SMC-4-65Cylinder W/O suction valve (R-22)

S&F in repair for compressor set Model No SMC-4-65 Gasket F-10

S&F in repair for compressor set Model No SMC-4-65 Gasket F-12

S&F in repair for compressor set Model No SMC-4-65 Seeger ring

S&F in repair for compressor set Model No SMC-4-65 Gasket B-05

S&F in repair for compressor set Model No SMC-4-65 Gasket L-17

S&F in repair for compressor set Model No SMC-4-65 Liquid line stainer (R-22)

S&F in repair for compressor set Model No SMC-4-65 Pilot control solenoid valve

S&F in repair for compressor set Model No SMC-4-65 Expansion valve

S&F in repair for compressor set Model No SMC-4-65 Hand shut off valve

S&F in repair shaft seal assembly of compressor of ACCEL make Model SMC-4-65 complete all as specified and directed

Dismantling complete ACCEL Compressor set Model SMC-4-100 of 33 TR Cap and overhauling the compressor with repair and checking of wornout holes of studs and providing over size studs with nuts & washers and gaskets . Rematlling and balancing of piston, replacement of piston ring,scrapper ring, split pin, castle nut, connecting rod bolt ,bushing for piston pin, and set of sealing ring of compressor and refitting the same after the repair/replacement duly all as specified and tested for smooth functioning of model SMC-4-100 complete all as specified and directed by Engr-in-charge. (Note-1:The all spare parts are measured and paid separately in relevent items) (Note-2: The arrangement of men power,T&P, settings by mechanic and testing shall be contractors responsibility)

S&F in repair for compressor set Model No SMC-4-100 suction valve ring plate 1.2mm

S&F in repair for compressor set Model No SMC-4-100 Discharge valve ring plate 1.20mm

S&F in repair for compressor set Model No SMC-4-100 Safty valve assembly

S&F in repair for compressor set Model No SMC-4-100 connecting rod bolt

S&F in repair for compressor set Model No SMC-4-100 Castle nut

S&F in repair for compressor set Model No SMC-4-100 Split pin

S&F in repair for compressor set Model No SMC-4-100 Half section of BRG STD

S&F in repair for compressor set Model No SMC-4-100 Bushing with collar STD

S&F in repair for compressor set Model No SMC-4-100 Shaft seal including 10 A-G

S&F in repair for compressor set Model No SMC-4-100 Piston with pin and rings

S&F in repair for compressor set Model No SMC-4-100 Piston ring

S&F in repair for compressor set Model No SMC-4-100 Scrapper ring

S&F in repair for compressor set Model No SMC-4-100 Bushing for piston pin

S&F in repair for compressor set Model No SMC-4-100 Valve spring

S&F in repair for compressor set Model No SMC-4-100 Spring for unloading ring

S&F in repair for compressor set Model No SMC-4-100 Set of Gasket ASL-1453

S&F in repair for compressor set Model No SMC-4-100 Set of sealing ring

S&F in repair for compressor set Model No SMC-4-100 Set of Neoprene O ring

S&F in repair for compressor set Model No SMC-4-100 Cylinder W/O suction valve (R-22)

S&F in repair for compressor set Model No SMC-4-100 Gasket F-10

S&F in repair for compressor set Model No SMC-4-100 Gasket F-12

S&F in repair for compressor set Model No SMC-4-100 Seeger ring

S&F in repair for compressor set Model No SMC-4-100 Gasket B-05

S&F in repair for compressor set Model No SMC-4-100 Gasket L-17

S&F in repair for compressor set Model No SMC-4-100 Liquid line stainer (R-22)

S&F in repair for compressor set Model No SMC-4-100 Pilot control solenoid valve

S&F in repair for compressor set Model No SMC-4-100 Expansion valve

S&F in repair for compressor set Model No SMC-4-100 Hand shut off valve

S&F in repair shaft seal assembly of compressor of ACCEL make Model SMC -4-100 complete all as specified and directed

S & F in repair of Sprinkler system for cooling tower complete all as specified and directed.

S&F in repair shaft seal assembly SMC 6-65 complete all as specified and directed

M&L in repairs to the cooling tower of 2 x 30/33 TR capacity by replacing the rusted GI wire mesh of existing gauge and weight of size 1.075Mx0.60x04 Nos with clamps, nuts and bolts etc complete all as specified and directed.

S&F in replacement fresh air grill of size 600mmx350mm having wire mesh, closing/opening dampers of suitable size with handle of PGI sheet of 20 gauge complete all as specified and directed.

S & F in replacement of Battery 12Volt 180 AH with initial charging maintenance free suitable for DG Sets complete all as specified and directed. Make- EXIDE EXPRESS or Equivalent

S & F in replacement of Battery 12Volt 150 AH with initial charging maintenance free suitable for DG Sets complete all as specified and directed. Make- EXIDE EXPRESS or Equivalent

Supply and charging refrigerant gas R-404/R-407, complete all as specified and directed. Make: Mafron

Dismantling the power supply of electric motor any type including dismantling from pump and taking to workshop with necessary transportation and opening the complete motor and rewinding the rotor with super enameled copper wire as per the existing gauge with necessary insulation, sticks and varnishing, including replacement of shaft bearing 02 Nos complete of capacity 20 to 30 HP complete all as specified and directed. (Note-1: The arrangement of men power,T&P, transport and testing shall be contractors responsibility)

All as per item No.142 above but of capacity 5 to 7.5 HP electric motor any type complete all as specified and directed.

All as per item No. 142 above but of capacity 10 to 15 HP electric motor any type complete all as specified and directed.

All as per item No.142 above but 1 to 3 HP electric motor any type complete all as specified and directed.

Dismantling complete Centrifugal /Mono Block pump set of any type and overhauling the pump re-threading of wornout holes of studs and providing over size studs with nuts & washers. Rematlling and balancing of shaft, replacement of gunmetal bush bearing and gland packing,nuts,bolts,washres,rubber gaskets of pump set. and refitting the same after the repair/replacement duly all as specified and tested for smooth functioning of capacity 10 to 15 HP complete all as specified and directed.(Note-1: The arrangement of men power,T&P, transport and testing shall be contractors responsibility)

All as per item No 146 above but capacity 5 to 7.5 HP complete all as specified and directed.

M&L for clean the fins & tank with acid/bleaching powder, tightening of nut bolt and clean the strainer of cooling tower of AC plant of any capacity complete all as specified and directed.

Supply and fixing in replacement of MCB 32 Amp TPN AC, 415 volts, 10 KAs complete all as specified and directed. Make : Legrand/HAVELLS/ L&T/C&S.

Supply and fixing in replacement of MCB 40 Amp TPN AC, 415 volts, 10 KA s complete all as specified and directed. Make ; Legrand/HAVELLS/ L&T/C&S.

Supply and fixing in replacement of MCB 25 Amp TPN AC, 415 volts, 10 KA s complete all as specified and directed. Make ; CG/HAVELLS/ L&T/C&S.

Supply and fixing in replacement of MCB 10 Amp TPN AC, 415 volts, 10 KA s complete all as specified and directed. Make ; Legrand/HAVELLS/ L&T/C&S.

Supply and fixing in replacement of MCB 63 Amp TPN AC, 415 volts, 10 KA s complete all as specified and directed. Make ; Make ; Legrand/HAVELLS/ L&T/C&S.

Supply and fixing in replacement of moulded case circuit breaker panel mounting type , AC, 415 volts,16 KA of capacity 63amps 4 pole complete all as specified and directed. Make ; Legrand/HAVELLS/ L&T/C&S.

Supply and fixing in replacement of moulded case circuit breaker panel mounting type , AC, 415 volts, 25 KA of capacity 100 amps 4 pole complete all as specified and directed. Make ; Legrand/HAVELLS/ L&T/C&S. .

Supply and fixing in replacement of moulded case circuit breaker panel mounting type , AC, 415 volts, 35 KA of capacity 125 amps, 4 pole complete all as specified and directed. Make ; Legrand/HAVELLS/ L&T/C&S.

Supply and fixing in replacement of moulded case circuit breaker panel mounting type , AC, 415 volts, 36 KA of capacity 250 amps 4 pole complete all as specified and directed. Make ; Legrand/HAVELLS/ L&T/C&S.

Supply and fixing in replacement of moulded case circuit breaker panel mounting type , AC, 415 volts, 50 KA of capacity 400 amps 4 pole complete all as specified and directed. Make ; Legrand/HAVELLS/ L&T/C&S.

M&L for clean the filter, cooling coil & blower of AHU for AC plant of any capacity complete all as specified and directed.

Taking down old unserviceable AHU complete cooling coil assembly from existing location and checking of water leakages in AHU cooling coil making repairs by brazing, gas welding,necessary copper tubes, copper jointing rods, joints etc after refixing the same its location properly and carry out the pressure testing after repairs of AHU for AC plant of any capacity complete all as specified and directed. (Note-1: The arrangement of men power,T&P,transportations etc and testing complete job shall be contractors responsibility)

Supply and fixing in replacement of Power contactor , 4Pole ,440v,50Hz ,400amp, : MNX 400 2 NO+2 NC complete all as specified and directed. Make: L&T/C&S/Havells

Supply and fixing in replacement Contactor, 3poles with AC coil of MNX 265 amps capacity complete all as specified and directed. Make: L&T/C&S/Havells

Supply and fixing in replacement Contactor, 3poles with AC coil of MNX 225 amps capacity complete all as specified and directed. Make: L&T/C&S/Havells

Supply and fixing in replacement Contactor, 3poles with AC coil of MNX 185 amps capacity complete all as specified and directed. Make: L&T/C&S/Havells

Supply and fixing in replacement Contactor, 3poles with AC coil of MNX 70 amps capacity complete all as specified and directed. Make: L&T/C&S/Havells

Supply and fixing in replacement Contactor, 3poles with AC coil of MNX 50 amps capacity, complete all as specified and directed. Make: L&T/C&S/Havells

Supply and fixing in replacement Contactor, 3poles with AC coil of MNX 45 amps capacity, complete all as specified and directed. Make: L&T/C&S/Havells

Supply and fixing in replacement Contactor, 3poles with AC coil of MNX 40 amps capacity, complete all as specified and directed. Make: L&T/C&S/Havells

Supply and fixing in replacement Contactor, 3poles with AC coil of MNX 32 amps capacity, complete all as specified and directed. Make: L&T/C&S/Havells

Supply and fixing in replacement Contactor, 3poles with AC coil of MNX 25 amps capacity, complete all as specified and directed. Make: L&T/C&S/Havells

Supply and fixing in replacement Contactor, 3poles with AC coil of MNX 18 amps capacity, complete all as specified and directed. Make: L&T/C&S/Havells

Supply and fixing in replacement of temperature gauge (thermometer) digital type 0-50 degree centigrade complete all as specified and directed.

Supply and fixing in replacement of control switches pressure gauge low pressure (LP) complete all as specified and directed.

Supply and fixing in replacement of control switches pressure gauge High pressure (HP) complete all as specified and directed.

Supply and fixing in replacement of HRC Fuse unit 400 Amps complete all as specified and directed.Make L& T /Havells /C&S

Supply and fixing in replacement of HRC Fuse unit 200 Amps complete all as specified and directed. Make L& T /Havells /C&S

Supply and fix phase failure preventor for the protection motors complete all as specified and directed. Make L& T /Havells /C&S

Supply and fixing in replacement Aluminium lugs suitable for above 120 sqmm upto 240sqmm cable complete all as specified and directed. Make: Dowells/C&S /Havells

Supply and fixing in replacement Aluminium lugs suitable for upto 120 sqmm cable complete all as specified and directed. Make: Dowells/C&S /Havells

Supply and fixing in replacement thermal over load relay of range 6.5 to 10 Amps complete all as specified and directed Make- CG/L&T/ BCH/C&S.

All as per item No 180 above but 15 to 22 Amps capacity complete all as specified and directed.

All as per item No 180 above but 30 to 50 Amps capacity complete all as specified and directed.

All as per item No 180 above but above 50 to 70 Amps capacity complete all as specified and directed.

All as per Item No. 180 above but above 70 to 100 Amps complete all as specified and directed.

Supply and fixing in replacement of indicating lamp set (RYB) LED type complete all as specified and directed.

S&F in replacement Star Delta Timer 0-30 Seconds duration complete all as specified and directed. make L&T/Havell's/C&S

Supply and fixing in replacement of electronic adjustable cyclic timer complete all as specified and directed. Make : EAPL /L&T/Minilec.

Supply and fixing in replacement industrial water pressure switch meter as per existing complete all as specified and directed.

Supply and fixing in replacement of On off push botton switch electrical complete all as specified and directed.

Supply and fixing in replacement Voltmeter digital type (0-500V) complete all as specified and directed. Make : AE/L&T/HPL

Supply and fixing in replacement Ammeter digital type (0- 100 Amps) complete all as specified and directed. Make : AE/L&T/HPL

Supply and fixing in replacement CT Coil 100/5 Amps complete all as specified and directed. Make : L&T/AE/C&S

Supply and fixing in replacement CT Coil 60/5 Amps complete all as specified and directed. Make : : L&T/AE/C&SL&T/AE/C&S

Supply and fixing in replacement CT Coil 30/5 Amps complete all as specified and directed. Make : L&T/AE/C&S

M & L for ladder of GI Pipe heavy 40 mm dia for cooling tower approx 6 mtr length complete all as specified and directed.

M&L in renewal for making of computerised colour/ printed of layout plan or brief details i.e history of installation/ machinery of various installations on and including 1.0mm thick plastic laminated acrylic sheet of size 1500x1200mm fixed to new hard boards with & including PVC beading of suitable size fixed to all edges of board with & including mild steel screws of suitable size complete all as specified and directed. Note:- Details i.e layout plan and brief details shall be provided by Engineer-in-Charge separately during execution.

M&L in renewal for making of computerised colour/ printed of name of installation and details of various installations on and including 1.0mm thick plastic laminated acrylic sheet of size 1000x600mm fixed to new hard boards with & including PVC beading of suitable size fixed to all edges of board with & including mild steel screws of suitable size complete all as specified and directed. Note:- Name & details of installations shall be provided by Engineer-in-Charge separately during execution.

M&L for Repairs to cooling tower of 12.5/22 TR by replacing the rusted GI Wire mesh of existing gauge and weight of size nuts ,clamps,and bolts etc complete all as specified and directed.

Supply,install, Commissioning and testing of capacity of cooling tower 100 TR, one no twin cell type corrosion resistant,fire retardant,FRP induced draft,rectangular/square type counter flow cooling tower of capacity 120% of plant running capacity with maximium allowable temperature 50 degree centigrade,drift loss 0.005% of water circulation,such as 80TR,water flow rate USGPM-1500,Inlet temp-97.5F,outlet temp-90F,wet bulb temp-83F,FRP materials,suitable mechanical eqpt-hot dip galvanized UV stabilized,PVC piping work,incl aluminium fan hub and blades-06 Nos,suitable size blades,fan motor 5 HP,960 rpm, dry weight 500 kgs,operating weight approx 1750 kgs, size suitable for as existing,incl sprinklers and functioning required connected items and including removing old unserviceable complete all as specified and directed.

M/S. KISHAN ENGINEERING (BID ID -3084837)

M/s M M Engineering Systems (BID ID -3084240)

S J ENTERPRISES (BID ID -3087213)

M/S.J.BIJAYA KUMAR PATRO (BID ID -3089386)