ADDN ALTEN OF MH 13 OFFICE COMPLEX AT ASC CENTRE SOUTH OF No 2 DET 963 INT AND FS UNIT UNDER GE CENTRAL BANGALORE

Amount

Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etc and removal of debris outside MoD land and depositing where directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15 cm thick above or below ground level and removal of entire debris as ordered outside MD land complete all as directed.

Demolition of unreinforced cement concrete as in roofs, floors (other than ground floors), in any description of beams, staircases, landing, chaj-jas etc including removing of existing APP membrane any thickness / Screed any thickness etc and removal of entire debris as ordered outside MD land complete all as directed.

Demolition of reinforced cement concrete as in any description (reinforcement cut as required to facilitate demolition) including removing of debris as ordered outside MD land complete all as directed.

Demolition of brickwork , block masonry or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of debris as ordered outside MD land complete all as directed.

Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MD land complete all as directed.

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site for credit & removal where directed.

All as per item 7 here-in-above but exceeding 1.5 Sqm but not exceeding 4 Sqm each

Dismantling of AC Corrugated or semi corrugated sheet etc any thickness including ridges as in roof covering and stacking at site at site for credit where directed and removal of debris to a outside MOD land and depositing where directed complete all as directed.

Dismantling boarding, any description, fixed in any position with nails. Complete all as directed.

Dismantling structural steel any type of steel including gates , purlins , rafters / roof coverings materials laid in walls excluding trusses complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, platform, aprons etc., laid, bedded and pointed in any mortar , stacking serviceable slbs at site and removal of entire debris as ordered outside MOD land complete all as directed.

Demolition of stone set paving any size & thickness laid in any description and removal of entire debris as ordered outside MOD land complete all as directed.

Demolition of drain or PVC pipe any dia including fittings laid in any description after necessary disconnection of water supply lines and removal of entire debris as ordered outside MOD land complete all as directed.

Surface excavation averaging 15cm deep and n.exc 30cm deep and getting out in soft/loose soil complete all as specified and directed

Excavation over areas not exc 1.5m deep and getting out in soft/loose soil complete all as specified and as directed.

Returning filling in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soft / loose complete all as specified and directed

Removing excavated material to a distance exc. 250m but not exc. 500m and depositing where directed complete all as specified.

M & L for Hard core of broken hard stone or boulders of guage not exceeding 63 mm , deposited spread as subbase to inter locking tiles in layers n.exc 15cm thick , watered & well rammed to true surface complete all as specified and directed.

M & L for PCC 1 :4 : 8 type D2 using 40 mm graded crushed stone aggregate as in foundation filling, sunken repairing & mass concrete complete all as specified and directed

M&L for cement concrete (1:2:4) type B1 using 20 mm graded crushed stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement. Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc

M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified & as directed

M&L for cement concrete 1:2:4 type B0, using 12.5mm graded crushed stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges all as specified & as directed.

M&L for reinforced cement concrete 1:2:4 type B0 using 12.5m graded crushed stone aggregate in chajjas / slabs with necessary form work complete allas directed. Note :- Reinforcement shall be measured and paid for separately.

M&L factory made pre cast PCC 1:3:6, type C1 (using 20 mm graded granite aggregate) as in block masonry with solid blocks, exceeding 10 cm in width and setting in CM 1:6 complete all as specified.

M&L for cutting holes in stone walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as required, exc half brick & not exc one brick (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall).

Supply only Integral Water Proofing Compound (ISI Marked) of Make : CICO, Acco Proof, Impermo, Aqua flex as approved.

S&F solid PVC door frame of size 50X47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification all as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and as directed..

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame complete all as directed.

S&F 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of required Solvent and fixing at site complete all as specified and as directed.

M&L for 18/19mm thick prelaminated particle board, medium density , flat pressed , single layer type or three layer type with BWR type adhesive , fixed with screws to frame work including necessary joining cleats , glazing clips , rubber neoprene packing , powder coated aluminium snap beading , screws etc complete all as specified & as directed.(Note : Quoted rate is deemed to be inclusive of fixing the board into the aluminium frame & other fixing elements & fixing it into the required places as a partion ).

S&F powder coated aluminium frame for doors, windows, ventilators, partitions with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed

S&F Powder coated aluminium sliding window (three way) frame & shutter with glazed shutter and with miremesh shutter /skeleton section with & including the following :- (i) Aluminium frame section 116x36.50x1.80mm. (ii) Aluminium shutter glazed/skeleton section 50x20x1.50mm thick. (iii) Aluminium grill size 50mmx50mm and 4 to 5mm thick bars complete all as specified. (iv) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape. (v) 4mm thick glass orinary quality and fixed with rubber gasket for with glazed shutter etc. (vi) Stainless steel wire mesh 0.36mm nominal dia avg aperature 1.14mm and fixed with rubber gasket for without glazed shutter etc. (vii) Aluminium disc /bow hanle and locking system complete

S&F Powder coated aluminium Ventilator (partially fixed glazing and Partially louvered glazing) with arrangement for exhaust fan & include the following :- (i) Aluminium frame section 45x25x1.80mm. (ii) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape. (iii) 4mm thick frosted glass orinary quality (partially fixed glazing and Partially louvered glazing) and fixed with rubber gasket for with glazed shutter etc.

S&F100 mm size butt hinges, heavy weight weight cold rolled mild steel and fixed .

S & F125 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S & F200 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S&F 150 mm size extruded aluminium alloy handles (ISI Marked) fabricated type anodised and fixed.

S&F 300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples including supply & fix second class hard wooden fillet, wrought , cross sectional area exceeding 3 Sqcm but n.exc 6 Sq cm fixed with nails complete all as directed.

S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Grade E-165 (Fe 290) and fixed in position

S&F mild steel framed work as in grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors and similar work including welding conforming to Grade E-165 (Fe 290), complete, all as specified & directed

S&F 10 mm dia and over TMT bars cut to length bent to shape required cranking including bending , hooking ends etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per serial item No. 46 here-in-before but 6 to 8mm dia -do-

S&F pre-painted galvalume (zincalume) aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/cladding to walls fixed with self tapping screws as specified.

Supply and fix Pre- painted galvalume aluminum zinc coating GI plain sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction all as specified and as directed.

Supply and fixing 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof, wall etc complete all as specified & as directed

S & F for Aluminium anodised snap grid frame for false ceiling of grid of size 605 x 605 including Hangers 6 mm dia GI (upto ceiling height) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40mm x 3 mm size 60 cm long & expansion hold fastereners 12.5 mm dia , 40 mm long complete all as specified & 12mm thick perforated particle board/tiles for insulation and accoustic purposes, 60 cm x 60 cm in size, fixed with screws to frame work or with staples on snap grid all including providing provision for light fixtures of any size complete all as specified.

Material and labour for removal of existing WPT course or any other kind of treatment surface over roof slab and cleaning of surface with wire brushes and water removing of unsolvent materials and depositing of the same outside MoD land and provide 10 mm thick screed bed/ bedding layer in CM 1:4 mixed with Water Proofing Compound (WPC) as per manufacturer instructions, including finishing the surface fair and even on RCC roof/ parapet once bedding layer of concrete is completely dried and apply oil bound bituminous primer @ 0.20 Kg/Sqm and providing 4mm thick APP modified water proofing membrane weighing not less than 4.00 Kg/Sqm reinforced with non woven polyster matt weighing not less than 160 gms/Sqm including minimum 10 cm side over laps and 15 cm end lap torch sealed and bonded as per detailed procedure as directed, apply a coat of blown grade hot bitumen 90/15 grade over the membrance @1.2 Kg/Sqm and finally finished the top surface with solar reflective bituminious aluminium paint @ 0.10 Kg/Sqm complete all as specified and as directed. Note: (i) The quoted rate is deemed to be inclusive of taking down & removal of debris , 10 mm thick 1:4 screed & complete APP treatment. (ii) WPC will be paid seperately (iii) The work shall be carried out only through manufacturer or their authorised applicator and a written guarantee for work shall be submitted by the manufacturer for the effectiveness of WPT (iv) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface.

M & L for 100 mm thick plain cement concrete 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in sub base of floor and finished the surface complete all as directed.

M & L for 75 mm thick plain cement conctere 1: 3 : 6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection including necessary form work as ordered & finished the surface fair and even complete all as directed.(Note : Quoted rate is deemed to be inclusive of form work).

M&L for vitrified ceramic tiles 8-10mm thick (square/rectangular), polished, coloured (Dark shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified and directed.

M & L non-skid coloured joint free ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:4 complete all directed and specified.

M&L coloured glazed ceramic tiles of size 350x250x7mm / 450x300x7 mm thick, on verticals surfaces, set and jointed in neat cement slurry including 10 mm thick back coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all directed. (Note for item Nos 55 to 57 : i) Quoted rate is deemed to be inclusive of cement screed. ii) Shade / pattern / Colour of tiles shall be got appproved before procurement).

M&L for factory made chequered cement concrete tiles, 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement & no pigment, over & including 20mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed.(Note : Quoted rate is deemed to be inclusive of cement screed.)

M&L for 18-20mm thick Sadherhali stone slab flooring, steps, jambs, pillars, window- cills, cooking platforms and like in 15 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granit laid complete all as directed including Rounding to edges complete.

All same as per item No 59 here - in - above but as in dado & skirting with 10 mm thick 1 : 3 cement mortar screed - do -(Note for item No 59 & 60 : i) Quoted rate is deemed to be inclusive of cement screed.)

M&L M-35 grade, 60 mm thick machine pressed, PVC moulded precast cement concrete interlocking paver blocks any shape and size with grey cement and pigment confirming to IS: 15658-2006, laid over and including 50 mm thick compacted sand cushion complete complete all as specified.(Note ; Quoted rate is deemed to be inclusive of 50 mm thick compacted sand cushoning).

M&L for rendering 20 mm thick in CM 1:4 on brick or concrete surfaces or surface other than fair faces brick work, finished even and smooth without using extra cement complete all as specified.

M&L for rendering 15 mm thick in CM 1:6 on brick or concrete surfaces or surface other than fair faces brick work, finished even and smooth without using extra cement complete all as specified.

M&L for rendering 10 mm thick in CM 1:3 on concrete surface as in ceiling finished the surface even and smooth without using extra cement & finally applying three coats of white wash to plastered surface of ceiling after necessary prepration of surface complete all as specified.(Note : Quoted rate is deemed to be inclusive of Three coats of white wash).

M&L preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 1-2mm thick white cement based wall care putty as ordered complete all as specified.

Complete removal of any type of existing treatment from walls surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 1-2 mm thick white cement based wall care putty as specified complete all as specified.

M&L prepration of newly plastered surface of walls applying 3 mm thick white cement based wall care putty , applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces applied by mechanical means i.e Airless spray including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed.

S&F sheet glass 6mm thick figured glass, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane complete all as directed.

All same as per item No 68 here-in-above but area of glass pane exceeding 0.5 Sqm in each pane -do-

M & L Two coats of 1st quality synthetic enamel paint over a coat of pink primer on new wooden surface of any description over 10 cm in width or girth including necessary preparation of new wooden surface complete all as directed.

M & L One coats of 1st quality synthetic enamel paint on old pained wooden surface of any description over 10 cm in width or girth including necessary preparation of old wooden surface complete all as directed.

M & L Two coats of 1st quality synthetic enemal paint over a coat of zinc chromate primer over any description of new steel surface over 10 cm in width or girth including necessary preparation of new steel surface complete all as directed.

M & L One coats of 1st quality synthetic enamel paint on old pained steel surface of any description over 10 cm in width or girth including necessary preparation of old steel surface complete all as directed.

M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth not otherwise described and treated with two coats of creosote oil complete all as specified

Taking down old rusted / wornout 20 mm bore GI tubing after necessary disconnection & S&F new 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed.

Taking down old rusted / wornout 25 mm bore GI tubing after necessary disconnection & S&F new 25 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed.(Note for item Nos 75 & 76 : Quoted rate is deemed to be inclusive for cutting / chasing of pipe line in Brick / stone masonry / concrete surface & making good to its existing specification with out any extra cost to Govt.).

S&F in repair 15mm dia cast copper alloy Bib taps fancy type , with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as directed.

S&F in repairs 15mm bore Stop valve /Angle cock , fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union

S&F in repairs 15mm bore Stop valve /Angle cock , cast copper alloy, fancy type chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union

S&F 15mm bore brass CP wall mixer for mixing hot and cold water screwed down with provision of over lead shower and cock for iron pipe and fixed complete all as specified. Prayag Cat No - 8475 or Equivalent

S&Fin repair health faucet ABS body with wall hook and 1.25 metre long SS braided rubber hose pipe and wall hook mounted type complete. Make: Prayag Cat No BEA-40 or equivalent in approved make.

S&F in repairs brass chromium plated shower rose 100 mm dia with or wihout swivel joint, any size, including fixing to steel pipe or union.complete all as directed.

S&F shelf of PTMT suitable for soap dish fixed with & including Chromium plated brass screws & plastic cleats (Minimum weight 300 gms) all as directed.

S&F in repairs Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and plastic cleats (Minimum weight 190gms).

S & F in repairs PVC connection 15 mm size with PTMT nuts, 450mm long complete all as specified

S&F Grating doom 100 mm dia of PTMT (Minimum weight 100 gms) complete all as specified and as directed

S&F 550 mm X 400 mm size white flat back vitreous china wash hand basin including chromium plated pillar tap (Make: CERA Cat No. S1053101/S1053102 6502) capstain head ,down high pressure with or without lettered 'Hot or Cold' with long screwed shanks & fly nuts suitable for 15 mm bore of pipe , PVC connection 15 mm dia 45 cm long with chromium plated nuts and bolts and suitable washers, PVC waste 32 bore CP waste coupling chain and plug , porcelain stopper including CI bracket fixed in repair complete all as diirected.

S&F in repairs vitreous china bowl type urinal flat back, size of 430 x 370 x 340mm (minimum) white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified.

S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, ‘P’ or ‘S’ trap, including connection to trap and flushing pipe including 10 liters capacity low level flushing cistern , antisyphonage pipe with PVC connection pipe 15 mm dia 600 mm long etc including provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with and including white PVC seat and cover closed pattern with flat bottom and MS chromium plated hinging device including provision of 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make of Pan CERA Cat No S1053101/S1053102 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

S & F in repairs PVC waste pipe of size 32/40 mm dia of suitable length as ordered for WHB/ Sink complete all as specified

S & F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints laid in excavated trenches or on floors in repairs complete all as directed.

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints laid in excavated trenches or on floors in repairs complete all as directed.(Note for item No 90 & 91 : Quoted rate is deemed to be inclusive of excavation & earthwork ).

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to wall in repairs complete all as directed.

S&F PVC (SWR) branch piece single,(single T) 110 mm dia equal or unequal with oval access door complete all as specified and directed.

S&F PVC (SWR) branch piece single,(single T) 75 mm dia equal or unequal with oval access door complete all as specified and directed.

S & F 110 mm bore, PVC (SWR) bends of any radius with access door complete all as specified and directed.

S&F 75 mm size PVC (SWR) floor trap with grating including jonting the same with solvent cement complete all as directed.

S&F 75 mm size PVC (SWR) multi floor trap with grating including jonting the same with solvent cement complete all as directed.

S&F 110mm bore PVC (SWR) vent cowl jonting the same with solvent cement complete all as directed.

Material and labour for PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed

M&L for 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars all as specified & as directed.

M&L for cutting into existing manholes/Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe.

Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site and S&F new 500 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer colour white both inside and outside with top cover including PVC float valve high pressure suitable for 25 mm bore of pipe with polythene float, gate valve iron screwed head 25 mm size, fixture hoisted and fixed in position where ordered and making necessary connection and testing complete all as directed.

Cutting/chipping the spalling concrete surfaces of columns, beams, facias, slabs, Chajjas & cartilevers etc., and trimming cleaning the surfaces of any thickness all as specified and directed. M/L for applying epoxy treatment for bonding old demolished concrete surfaces incl application of one coat of notozinc primer to the exposed reinforcement and over plastering in CM 1:4 average 20mm thick finishied even and smooth without using extra cement to level the surface etc incl necessary scafolding as required at site and where required complete all as specified and directed

E&M : Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators, sockets etc. to be measured separately), removing taken down materials to a place where ordered for crediting including making good disturbed surfaces of walls, floors, etc to match with the existing surface complete all as directed..

Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic conduit (Medium Grade) concealed on surface conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :-(a) One light / Fan / bell point controlled by one 5 Amps switch one way

(b) One 3 pin socket point 5/6 Amp on independent board

(c) One 3 pin socket point 5/6 Amp on same board with other switches.(to be provide new point as user reqairment)

All as per item No. 108 here-in-above but with 2.5sqmm ( Nominal area ) cable with 2.5 Sqmm size copper earth continuity conductor for 3 pin 15/16 A socket outlet on independent board complete all as specified and directed.

Supply and fix Switch piano, flush button single pole, 5 Amps one way.

Supply and fix Switch sokcet combination flush type 6 Amp 2/3 pin muliti purpose

Supply and fix Switch socket combination flush type 6/16 Amps 3/3 pin universal multipurpose

Supply and fix switch bell push botton single pole 5 Amps 230 Volts one way complete all as specified and directed.

Supply and fix in repair Fan regulator electronic, step & switch type 230 volt, suitable for 1200/1400mm sweep ceiling fan. Make : Anchor/Havell/Polycab

Supply and fix in repair Door bell electronic, music type, 230 volt AC. Make : Anchor/Havell/Polycab

S&F in replacement LED tube light fitting of 20 watts 6000K , 230 volt, with aluminium extruded channel powder coated with diffuser for glare free light complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

Taking down existing light fittings fixed in any description S&F 34 W LED 2'x2' light fittings recessed mounting including driver LED edge-lit luminare suitable for armstrong/ Grid ceiling with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete for low ceiling application fixed as per manufacturers instructions and making necessary electrical connections and testing on completion complete all as directed.Make : Havells/wipro/surya/Philips

Taking down existing light fittings fixed in any description S&F 34 W LED 2'x2' light fittings surface mounting including driver LED edge-lit luminare suitable for armstrong/ Grid ceiling with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete for low ceiling application fixed as per manufacturers instructions and making necessary electrical connections and testing on completion complete all as directed.Make : Havells/wipro/surya/Philips

Taking down existing light fittings fixed in any description S&F security light light fittings 1x 25 Watt LED street light with New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08 with all accessories and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size fixed as per manufacturers instructions and making necessary electrical connections and testing on completion complete all as directed.Make : Havells/wipro/surya

S&F in repair security light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 32mm X 5 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole complete all as specified and directed.

S&F Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 8 way horizontal type, singal door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix in replacement MCB single pole 6 to 32 Amps 240 volts, C series, 10 kA rupturing capacity

Supply and fix in replacement MCB single pole & neutral 40 Amps 240 volts, C series,10 kA rupturing capacity

Supply and fixing in repair sheet metal enclousure single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 'C' series 10 KA breaking capacity 230 Volt all as specified

Taking down old existing sub main wiring and provide new submain wiring with 2 runs of 4 Sqmm single core PVC insulated, unsheathed, multi stranded copper conductor and one single core 4 Sqmm PVC insulated , unsheathed , multi stranded copper cable as earthing lead as per IS : 694 / 1990 drawn through and including non-metallic PVC rigid conduit of size 20/ 25 mm dia concealed in walls etc with all accessories such as Tees, Elbows, junction box, reducers etc and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. (Note :- 2 runs 4 Sqmm cable , one run 4 Sqmm cable and one run of PVC shall be measured as one unit length) .

S & F ceiling fans complete with blades, down rods,electronic regulator and accessaries 230v,1200mm sweep, Min air delivery 210 CFM with service Value 6.00 BEE Five star rated with Brushless direct current motor (BLDC) Provn of twin core cable of suitable size for ceiling rose to connector connecting of earth wire as complete all as directed

Taking down defective / unservicable any size & RPM of exhaust fan after necessary electrical disconnection & Supply & fixing and testing exhaust fan of 200mm sweep heavy duty, double ball bearing, 1400 RPM, plastic body , suitable for SP 230 / 240 volt, 50 Hz AC supply complete with louver shutter including fixing in exsiting position & connecting with & including 3 Nos 1.5 sqmm single core, PVC insulated but unsheathed FRLS 1100 volts grade cable with multi-stranded copper conductor from ceiling rose to fan finally making good the disturbued surface of walls both internal & external to its original specifications to the satisfaction of Enginner-in-charge complete all as directed. Make : Havels Turbo Force SP or equivalent oin Bajaj/ CG / Orient / Usha as approved (Note : The taken down fan shall be deposited to MES E/M Store without any extra cost to Govt.)

Taking down ceiling/exhaust fan dismantling and painting of ceiling/exhaust fan complete at site with synthetic enamel paint by spraying incl (fittings with filler) one coat after cleaning all dust etc incl connecting up. Provn of twin core cable of suitable size for ceiling rose to connector connecting of earth wire incl replacement of fan capacitor 2.5/3.15 MFD,canopy, bearing/bush, rubber bushes minor nuts bolts screws washers greassing in fan bearing & refix same complete all as directed

M & L for Earthing to Main panel complete with galvanized steel earth plate electrode 600 x 600 x 6. mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 6.0 mm dia as earthing lead of bolts,nuts,check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point all as specified or indicated including testing on completion complete all as directed.

S&F 5 star rated Inverter type Split Air conditioning unit working on Gas R-32(Refrigerant) of capacity 1.5 Ton consisting out door unit with fan motor, hermetically sealed rotary compressor with accessories and condensing unit of copper tubing complete duly connected with separately errected indoor unit with blower motor, plasma insulated copper tubing upto 5 mts suitable for 1.5 TR, including MS Stand duly painted, Gas charging internal copper wiring, remote control including making opening in stone / brick wall by cutting, drilling for placing ducts, pipes etc and making good the distured surface of wall as per its original specifiaction including mounting brackets for wall /stand to rest on slab etc AC installed as per manufacturers instructions and testing on completion to entire satisfaction of Engineer-in-charge complete all as directed. Make : Blue star Model No. IC518DBTU or equivalent in Voltas, Mitsubhi, Dakin, Carrier

m/s raghavendra kulkarni (BID ID -3381996)