ADDN/ALTN AND SPECIAL REPAIRS TO NAVAL SHOOTING COMPLEX AT INS AGRANI COIMBATORE

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed .

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed .

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work,vertical or to batter flat and rough finished surface complete all as specified and directed .

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions circular on plan with rough finished surface of concrete complete all as specified and directed .

M& L for RCC(Nominal Mix) M 20 (20mm graded stone aggregate) for foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed .

M& L for RCC(Nominal Mix) M 20 (20mm graded stone aggregate) for columns, pillars, piers, posts and struts complete all as specified and directed .

Returning, filling in soil/loose soil, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed .

Removing excavated materials to a distance n. ecx 50 m and deposited where directed at a level n. exc. 1.5 n above the starting point complete all as specified and directed .

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed .

All as per Item No. 9 above,but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4,with using WPC complete all as specified and directed . (WPC to be measured separately).

M&L for applying two coats of cement based paint to newly plastered surface including preparation of surface complete all as specified and directed .

Dismantling boarding of any description ,fixed in any position with screws all as specified and directed.

Dismantling posts or struts in concrete, brick work, masonary, etc (wood, steel, or RCC) any section including separating and cleaning of reinforcement, taking out embedded portion and making good disturbed ground all as specified and as directed.

Supply only Water proofing compound all as specified and as directed.

S&F second class soft wood boarding 40 mm thick, Planed one side with butt joints fixed with nails all as specified and as directed.

M&L for preparation of new wooden surface not otherwise described,over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer including preparation surfaces all as specified and as directed.

S&F rolled mild steel in Roof trusses (framed), trussed, purlins , crane gantries , rails and fastenings and heavy bracket framing (Beam,tee,angle,channel or flat sections) including distance pieces, cleats etc. Fe 410W(Gde E-250) quality-A ,all as specified and as directed.

S&F rolled mild steel in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment of Fe 410-W (Gde-E-250) quality-A,all as specified and as directed.

M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface of any description over 10cm in width or girth, not otherwise described all as specified and as directed.

VIJAYA ENTERPRISES

p.chinnasamy