Construction of additional two lane Bridge at 33/4 of Thirumazhisai-Uthukkottai road (Left side)

Amount

Earth work excavation in all classes of soils except hard rock requiring blasting and depositing on bank with all leads and lifts as per SS20B, including cost of all labour, equipments and all other incidental charges such as baling out water, providing and maintaining necessary coffer dams, sheeting shoring, bracing, and their subsequent removal, removal of all logs, stumps, grubs and other deleterious matter and obstructions, trimming bottom of excavation backfilling and clearing the site and disposal of all surplus materials etc, complete as per relevant standard specification, for FOUNDATION OF PILE CAPS BELOW ABUTMENTS AND PIERS as per MORT&H Specificaton No.304, 305

Providing and driving in position permanent M.S liners including cost and conveyance to the site and fabricating charges and tools and plants and driving MS liners 6mm thick to be left permanently with the pile shaft as per requirement and as per standard specification and placing from the bottom with all leads and lifts using 6mm M.S sheet etc., complete as per MORT&H Specificaton No.1100

Reinforced cement concrete cast-in-situ bored piles of 1200mm diameter M35 Design mix using 20mm ISS HBG graded metal with minimum cement content of 400 kg. per cum. maximum water cement ratio of 0.4 and slump of 150-200 mm by tremie concreting including cost and conveyance of all materials to site and cost of cement at site but excluding cost and fabrication of steel and placing it in position before concreting, setting up of piling equipment, shifting the same from one pile location to another pile location, dismantling and including all labour for boring through all soils, leading the excavated earth to a distance of 200m including forming of working platform over the river bed for accommodation piling equipment, forming approaches to the working platform, mixing concrete, filling it in position by tremie pipe, cutting of the pile head to cut-off level for casting pile cap, including diversion of water course if necessary, forming and maintaining protective bunds and all other incidental charges etc., complete as per standard specifications, forming and maintaining protective bunds and all other incidental charges including cost of necessary initial and routine pile load test charges etc., complete for PILES UNDER ABUTMENTS, WINGS & PIERS as per MORT&H Specificaton No.1100

Cement concrete M15 (Nominal mix 1:2:4) using 40 mm ISS HBG graded metal including cost and conveyance of all materials to site and cost of cement at site including cost of form work, including soft water, labour charges for mixing, transporting, laying compacting and curing concrete, working at depths, tools and plants and incidental charges such as bailing out water, maintaining of protective bunds, cofferdams, shoring, strutting etc., complete as per relevant standard specification for LEVELLING COURSE BELOW PILE CAP UNDER ABUTMENTS AND PIERS as per MOR&H Vth specification No.1000, 1500, 1700, 2200

Vibrated Reinforced Cement Concrete of grade M35 Design Mix using 20mm ISS HBG graded metal including cost and conveyance of all materials to site and cement at site, excluding cost and fabrication of steel, including cost of form work and centering soft water, labour charges for mixing, transporting, laying and curing concrete , working at depths, hire charges for tools and plants and incidental charges such as bailing out water, maintaining of protective bunds, cofferdams, shoring, strutting etc., complete as per relevant standard specification, for PILE CAPS UNDER ABUTMENTS, WINGS AND PIERS s per MORT&H Specificaton No.1000, 1500, 1700, 2200

Vibrated reinforced Cement Concrete M35 (Design mix) using 20mm ISS HBG graded metal including cost and conveyance of all materials to site and cost of cement at site, but excluding cost and fabrication of steel, but including cost of form work and centering, soft water labour charges for mixing, transporting, laying, curing concrete , working at heights, hire charges for tools and plants including all other incidental charges, as per standard specification etc. complete for ABUTMENTS AND WING SUBSTRUCTURE s per MORT&H Specificaton No.1000, 1500, 1700, 2200

Vibrated Reinforced Cement Concrete M35 (Design mix) using 20mm ISS HBG graded metal, including cost and conveyance of all materials to site and cost of cement at site, but excluding cost and fabrication of steel but including cost of formwork and centering and soft water labour charges for mixing, transporting, laying, curing concrete , working at heights, hire charges for tools and plants, including all other incidental charges, as per standard specifications etc., complete for BED BLOCK CUM DIRT WALL OVER ABUTMENTS as per MORT&H Specificaton No.1000, 1500, 1700, 2200, 2300

Vibrated reinforced Cement Concrete M35 (Design mix) using 20mm ISS HBG graded metal including cost and conveyance of all materials to site and cost of cement at site, but excluding cost and fabrication of steel but including cost of form work and centering, soft water, labour charges for mixing, transporting, laying, curing concrete , working at heights, hire charges for tools and plants, including all other incidental charges, etc., as per standard specification, complete for PIER COLUMNS as per MORT&H Specificaton No.1000, 1500, 1700, 2200, 2300

Vibrated Reinforced Cement Concrete M35 (Design Mix) using 20mm ISS HBG graded metal including cost and conveyance of all materials to site and cost of cement at site but excluding cost and fabrication of steel but including cost of form work and centering, soft water, labour charges for mixing, transporting, laying, placing in position vibrating and compacting, finishing curing concrete working at heights, hire charges for tools and plants including all other incidental charges, etc., complete, as per standard specification for CAPPING BEAMS OVER PIERS COLUMNS as per MORT&H Specificaton No.1000, 1500, 1700, 2200, 2300

Vibrated reinforced Cement Concrete M35 (Design mix) using 20mm ISS HBG graded metal including cost and conveyance of all materials to site and cost of cement at site, but excluding cost and fabrication of steel but including cost of form work, and centering, soft water, labour charges for mixing, transporting, laying, placing in position vibrating and compacting, finishing curing concrete , working at heights, hire charges for tools and plants, including all other incidental charges, etc., complete as per standard specification for RCC PEDESTALS OVER ABUTMENTS AND PIERS as per MORT&H Specificaton No.1000, 1500, 1700, 2200, 2300

Supplying and Fixing of Elastomeric bearing of size 50x30x8cm including cost and conveyance to work site, labour for fixing the bearing in correct position and all other incidental charges etc., as per standard specification as per MORT&H Specificaton No.2005

Vibrated Reinforced Cement Concrete M35 Grade, (Design mix) using 20mm ISS HBG graded metal including cost and conveyance of all materials to site and cost of cement at site, but excluding cost and fabrication of steel but including cost of form work, and centering, using steel grips and bracing, soft water, labour charges for mixing, transporting, laying , placing in position, vibrating and compacting, finishing curing concrete , working at heights , hire charges for tools and plants, including all other incidental charges, etc., complete as per relevant standard specification for T-BEAMS AND CROSS BEAMS as per MORT&H Specificaton No.1000, 1500, 1700, 2200, 2300

Vibrated Reinforced Cement Concrete M35 (Design Mix) using 20mm ISS HBG metal including cost and conveyance of all materials to site and cost of cement at site, but excluding cost and fabrication of steel but including cost of formwork, and centering using steel grips and bracing, soft water, labour charges for mixing, transporting, laying, placing in position, vibrating and compacting, finishing curing concrete , working at heights, hire charges for tools and plants, including all other incidental charges, including inspection chamber, inclusive of 150mm dia PVC pipe ducts and all other accessories of footpath etc., complete for DECK SLAB, FOOTPATH AND SAFETY KERB as per MORT&H Specificaton No.1000, 1500, 1700, 2200, 2300

Vibrated Reinforced Cement Concrete M30(Design Mix) using ISS HBG graded metal including cost and conveyance of all materials to site and cost of cement at site but excluding cost and fabrication of steel, but including cost of formwork, and centering, soft water, labour charges for mixing, transporting, laying, placing in position, vibrating and compacting, finishing curing concrete , working at heights, hire charges for tools and plants including all other incidental charges, etc., complete for RCC HAND RAILS AND POSTS OVER DECK SLAB s per MORT&H Specificaton No.1000, 1500, 1700, 2200, 2300

Vibrated reinforced cement concrete M40 (Design mix) using 20mm ISS HBG graded metal including cost and conveyance of all materials to site and cost of cement at site but excluding cost and fabrication of steel but including cost of form work labour charges for mixing, transporting, laying, curing concrete, working at heights, soft water hire charges for tools and plants, including all other incidental charges etc., complete for INNER CRASH BARRIER as per MORT&H Specificaton No.811, 1000, 1500, 1700, 2300, 2703

Vibrated reinforced cement concrete M40 (Design mix) using 20mm ISS HBG graded metal including cost and conveyance of all materials to site and cost of cement at site but excluding cost and fabrication of steel but including cost of form work labour charges for mixing, transporting, laying, curing concrete, working at heights, soft water hire charges for tools and plants, including all other incidental charges etc., complete for OUTER CRASH BARRIER(D/S) as per MORT&H Specificaton No.811, 1000, 1500, 1700, 2300, 2703

Providing and fixing of Galvanized Iron Drainage spouts 100mm dia as per MOST drawing SD/205 with grating arrangements at top as shown in the drawing using 12mm X 25mm flats for grating arrangements and 100mm dia drainage spout projecting beyond the bottom of deck slab as shown in the drawing, including cost and conveyance of Cast Iron pipes and flats and fixing them in position, etc, complete as per MORT&H Specificaton No.2705

Vibrated Cement Concrete M15 (Nominal mix 1:2:4) using 40mm ISS metal including cost and conveyance of all materials to site and cost of cement at site, including cost of form work and centering, soft water, all labour charges for mixing concrete, laying, hire charges for tools and plants , compacting, curing with all leads for soft water, working in heights including all other incidental charges, form work including 150mm dia PVC pipe cable duct for utility etc, complete for BASE COURSE BELOW APPROACH SLAB AND FOOTPATH RAMP as per MORT&H Specificaton No.1000, 1500, 1700, 2200, 2704

Vibrated Reinforced Cement Concrete M30 (Design mix) using 20mm ISS HBG graded metal, including cost and conveyance of all materials to site and cost of cement at site, but excluding cost and fabrication of steel but including cost of form work, and centering, soft water, labour charges for mixing , laying, placing in position, vibrating and compacting, finishing, curing concrete, working at heights, soft water, hire charges for tools and plants, including all other incidental charges, etc., complete for APPROACH SLABS as per MORT&H Specificaton No.1000, 1500, 1700, 2200, 2704

Vibrated Cement concrete M15 (Nominal mix) 1:2:4, using 40mm ISS HBG graded metal including cost and conveyance of all materials to site and cost of cement at site including cost of form work, soft water, labour charges for mixing, transporting, laying and curing concrete working at heights, Tools and Plants and incidental charges etc; complete as per relevant standard specification, for PARAPET OVER WINGS as per MORT&H Specificaton No.1000, 1500, 1700, 2200, 2300

Vibrated cement Concrete M30 (Design mix) using 65% of 25mm,25% of 12mm and 10% of 6mm ISS HBG graded metal including cost and conveyance of all materials to worksite including cement at site but excluding cost and fabrication of steel but including all labour charges for mixing concrete, laying, hire charges for tools and plants, compacting, curing concrete, soft water, including all other incidental charges formwork, cost of premoulded expansion joints and fixing the same in position etc., complete for WEARING COAT OF 75mm UNIFORM THICKNESS OVER DECK SLAB AND APPROACH SLAB as per MORT&H No.2702

Supplying and Installation of STRIP SEAL EXPANSION JOINT system, conforming to specifications for Roads and Bridges works -V Revision; 2001 Published by Ministry of Surface Transport (Road Wing) in the 40mm wide expansion gap provided in between Decks over piers and in between deck and dirtwall over abutment with fatigue tested structural steel section at the nosing and anchorage assembly, including cost and conveyance of all materials, cost of testing as per MORT&H specifications, including labour, equipment and incidental charges for fixing the joints complete in all respects as per specifications as per MORT&H Specificaton No.2600

Providing and fixing PVC Seepage pipes of 100mm dia. PVC pipes of required lengths for abutments and wings including cost and conveyance of all materials to work site cost and labour for 900mm dia. Semi-spherical back fill arrangements with 100mm size broken ganite chips at the periphery and labour charges for fixing, etc.,to drain the backfill in BETWEEN THE ABUTMENT AND WINGS as per MORT&H No.2706 `

Providing FILTER MEDIA behind Abutment and wing walls for 600mm thickness using filter material conforming to clause 309.3.2.2of MORT&H well packed with smaller size towards the soil and bigger size towards the wall including cost and conveyance to worksite including labour all other incidental charges etc., complete as per MORT&H Specificaton No.1000

Filling behind Abutments and Wings as per Appendix.6 of IRC : 78-2000 with clean gritty free draining gravel including cost and draining gravel having PHI Value more than 35 conveyance of gravel to worksite, laying, handling charges and filling in layers, tamping under optimum moisture content to get the maximum density, including watering, with all leads for water, including hire charges for tools and plants and all other incidental charges etc., complete as per MORT&H Specificaton No.1000

Supply and Fabrication of High Yield Strength Deformed Bar with Grade Designation Fe-500D, conforming to IS:1786- 1985, steel required for all RCC items of works involved in the schedule cost of steel at site fabrication, labour charges for cleaning the rods, straightening, cutting, bending, tying grills, including over laping to the required length wherever necessary, and placing the reinforcement in position as specified in the drawings, including cost of binding wire, provision of spacer bars, cover blocks and all other incidental charges etc, complete Fe - 500D grade as per MORT&H Specificaton No.1600

Supply and fabrication of Fe-240 steel required for all RCC items of works involved in the schedule cost of steel at site cost of providing and cost of fabrication, lablour charges for cleaning the rods, straightening, cutting, bending, tying grills including over lapping to the required length wherever necessary and providing to the reinforcement, placing the reinforcement in position as specified in the drawings including cost of form work, cost of binding wire of provision of spacer bars, cover blocks and all other incidental charges etc complete, Fe - 240 Grade as per MORT&H Specificaton No.1600

Supply and fixing of High quality of PVC Duct pipes of 160 mm dia 4 Kg/cm2 including cost and conveyance of pipes to the sie and fixing in position to proper grade and level, including labour charges for fixing and including all other incidental charges complete for providing utility services in footpaths as per Section 2706 of MORT&H Specifications

Forming embankment with Carted Earth including cost and conveyance of 15 km carted earth to work site including labour charges for filling in layers as specified by the departmental officers including watering with all leads for water including labour charges for compacting, tamping, ramming under optimum moisture, content to obtain the maximum density and all other including charges etc., complete as per standard specifications for APPROACH ROAD 95% COMPACTION as per MORT&H Specificaton No.304, 305

Construction of Subgrade of 50cm including cost and conveyance of 15 km soil to work site including labour charges for filling in layers as specified by the departmental officers including watering with all leads for water including labour charges for compacting, tamping, ramming under optimum moisture, content to obtain the maximum density and all other including charges etc., complete as per standard specifications for APPROACH ROAD 97% COMPACTION as per MORT&H Specificaton No.304, 305

Construction of Granular sub-base Grade-V of 200mm thick by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 for Approach road.

Providing and laying spreading and compacting graded stone aggregates to Wet Mix Macadam 250mm. thick in two layers of 125mm each thick specification including premixing the materials with water at OMC in mechanical mix plant carriage of mixed material by tipper to the site laying in uniform layers with pavers in sub base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per clause 406 of MORTH Rev-5 for Approach road.

Providing and laying Prime Coat over WBM/WMM surface using 7Kg of Emulsion Bitumen(SS1) per 10sqm for preparatory to another bituminous construction over it, including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per Clause 502 of MORTH Rev-5

Providing and laying Tack Coat over WBM/WMM surface (treated with primer) using 2.50Kg of Bitumen Emulsion(RS1) per 10sqm for preparatory to another bituminous construction over it including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per Clause 503 of MORTH Rev-5

Providing and laying 70mm consolidated thick Dense Bituminous Macadam using 0.24 cum of 26.50-13.20mm, 0.25 cum of 13.20-2.36mm and 0.23 cum of 2.36mm&below and with 53.20 Kgs of VG30 bitumen for premixing per 10sqm including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to worksite, spreading the mix to uniform thickness of 50mm with paver to the specified grades and cross sections and compacted by Vibratory/Pneumatic Roller to the required density etc., including labour for attending to paver at site etc., including hire charges and fuel charges for 20-30t CMP with bitumen boiler, tipper trucks, Paver Finisher/9m paver finisher, Vibratory/ Pneumaticrollers and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 505 MORTH Rev-5.

Providing and laying Bituminous Concrete to 40mm thick using 0.13cum of 19.00-9.50mm, 0.17cum of 9.50-2.36mm and 0.26 cum of 2.36 and below with 50.30kgs of VG30 bitumen for premixing per 10 sqm including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing them in required temperature in central hot mix plant 20-30ton capacity, conveying the mix by tipper trucks to work site, spreading the mix to uniform thickness of 30mm with mechanical sensor paver finisher to the specified grades and cross sections and consolidatedby8-10tonne Vibratory/Pneumatic Roller to the required density etc., including labour for attending to paver to site etc., including hire charges and fuel charges for20-30t CMP with bitumen boiler, tipper trucks, Paver Finisher/9m paver finisher, Vibratory/Pneumatic roller and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 507 of MORTH Rev-5.

Painting two coats with approved Cement Paint over the priming coat surface using first class cement paint over the cement plastered surface including cost and conveyance and all labour charges for cleaning, preparing the surface painting and curing all etc., complete.

Painting two coats with ready mix Plastic Emulsion Paint using first quality plastic enamal paint over the priming coat surface over the cement plastered surface including all cost and conveyance and all labour charges for cleaning, preparing the surface, painting and curing etc., complete. (Crash barrier, Parapets and Hand rails)

Earth work excavation in all classes of soil except hard rock not requiring blasting and depositing on bank with all leads and all lifts as per SS20B including cost of labour, equipments and all other incidental charges such as bailing out water, providing necessary coffer dam sheeting, shoring, bracing and their subsequent removal, removal of all logs, stumps and other deleterious matter and obstruction trimming bottom of excavation, backfilling and clearing the site and disposal of all surplus earth with all leads etc,. complete as per standard specification for Foundation of Revetment Toe wall as per MORT&H Specificaton No.304, 305

Vibrated Cement concrete of Grade M15 (Nominal mix 1:2:4) using 40mm ISS HBG metal including cost and conveyance of all materials to site and cost of cement at site including form work and centering using soft water, labour charges for mixing, transporting, and place in position, laying vibrating and compacting, curing concrete, working at depth Tools and Plants and incidential charges such as bailing out water, maintaining of protective bunds, cofferdams, shoring, structting etc; complete as per relevant standard specification, for Toe walls of Revetment as per MORT&H Specificaton No.1000, 1500, 1700, 2200

Laying with gravel including cost and conveyance, laying, handling charges and filling in layers, tamping under optimum content to get maximum density including watering and all other incidental charges etc., complete for backing to CC.Block Revetment as per MORT&H Specificaton No.1000, 2500, 2504

Manufacturing and fixing cement concrete blocks of size 250 x 250x 300 mm in CC 1:2:4, nominal mix (M15) using 20mm ISS size HBG metal including cost and conveyance of all materials to worksite and cement site including conveyance and handling charges for the same at both ends including all other incidental charges for REVETMENTS including all other incidental charges including pointing with CM 1:3 etc., complete as per MORT&H Specificaton No.1000, 1700, 2500, 2504

Dismantling the Plain Cement Concrete and clearing away 2km lead from the work site and carefully stacking the usefull materials for reuse on the road side as directed by the departmental officers including all labour and incidental charges etc., complete. s per MORT&H Specificaton No.202

Dismantling the grouted stones apron or revetment stacking within 2 km lead. s per MORT&H Specificaton No.202

Sub Total Bid Price (in figures)

GST @ 12% of above all Schedules (in figures)

MYANSINFRASTRUCTURES