NIT No-13 / EE (EnM) WnS S-III item No-01

Supply of Horizontal Non-Clog /solid handling pump SHM 100/26N With Impeller-SS, Shaft-SS Shaft Sleeve-SS , CI Body in fitted condition with suitable bearing along with TEFC IE2 AC 3 phase squirrel cage Induction Motor with IP-55 Protection, With coupling & coupling Guard Duties of pump:-Head-10 mtrs, Discharge-150 M3/Hr, Eff:-64% RPM-1475,Suction/Delivery Size 125 X 100 mm Motor Rating:-7.5 KW/10 HP RPM-1475, Phase-3, Volt-415,HZ-50 Make :- Kirloskar / M&P /Any DJB Approved make

Fabrication of M. S base frame as per site requirement by providing M.S Chanel of size 100X50mm approx-5 mtr. Horizontal/ vertical member made out from MS channel of size 75X40X4.8mm approx-2 mtrs which is to be the welded on the base frame from alignment of pump set.

Providing of MS blank flange 100 mm dia. Of thickness 16 mm

Providing of MS blank flange 125 mm dia. Of thickness 20 mm

Providing of flanged type non-rising valve of size 100 mm with design std. IS 14846 PN 1.0 having CI body, dome, wedge confirming to IS:210 Gr. FG 260 & bronze wedge rings, SS spindle, gland packing, greasy jute, packing fasteners and natural rubber gasket .Make- Kirloskar/IVC.

Providing of flanged type non-rising valve of size 125 mm with design std. IS 14846 PN 1.0 having CI body, dome, wedge confirming to IS:210 Gr. FG 260 & bronze wedge rings, SS spindle, gland packing, greasy jute, packing fasteners and natural rubber gasket. Make- Kirloskar/IVC

Providing of 100 mm dia Non return Valve CI D/F as per IS 14846 PN 1.0 Make – Kirloskar / IVC

Providing of Rubber insulation sheet, size 1.5 mm thickness. Make :- Jyoti/National

Providing of MS foundation Bolts of sizes 16 mm x 450 mm ISI mark

Providing of MS nut bolt with washer as per site requirement ISI mark

Disconnecting electric connection of motors and Dismantling of pump sets from foundation, removing of coupling, Sluice Valve, NRV, Gap pieces, Taper pieces on suction & Delivery side by cutting of old rusted nut bolt with the help of gas cutter, welding machine by taking proper safety precaution including heavy manual labour and taking out the material for safe and suitable place as per direction engineer in charge. Closing the suction and delivery line with the help of MS blank flange.

Demolishing RCC work manually by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 mtrs lead as per direction of engineer in charge . 15.3 DSR-2018 (1.7 x .75 x 1.2 ) 1.53 X 2 =3.06 Cum

Providing and lying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering – All work up to plinth level: 1:2:4. ( 1 cement :2 coarse sand : 4 grade stone Volume of foundation 10 HP Electric pump set= 2 ( LxBxH) (1.5 m x 0.75 m x 1.2 m)= 1.35 cum X 2=2.7 5.1.3 DSR 2018

Centering and shuttering including strutting, propping etc. And removal of form for: For foundation, footing, bases of columns etc. for mass concrete. 5.9.1 DSR 2018

Steel reinforcement for RCC work for including straitening, cutting, bending, placing in position in binding all complete up to plinth level. Cold twisting bars 5.22.3 DSR 2018

Fixing the M.S. base frame on the RCC foundation the job includes proper leveling and alignment

Installation of Motor pump set with proper alignment and also making of all electrical connection, fixing of new motor pump sets along with NRV, Sluice Valves, Gap pieces, Taper pieces on suction & Delivery side pipe and flange welding with the help of all labour like Fitter, welder, cutter, helper, beldar, electrician and supervisor etc. and material like welding machine cutter set, Oxygen cylinder, welding rods and T&P etc.

Loading, unloading by heavy labour and cartage up to site i/c Motor p/set, Sluice valve NRV, etc. It also i/c the all job work which required to commissioning the SPS at per site requirement.

Testing the pump set on no load & on full load after commissioning of all connection.

HYDROCON ENGINEERS