TANK REPAIR(64M DX 13M HT)

DISMANTLING OF — PER SCOPE OF WORK AND TERMS AND CONDITIONSATTACHED.

Dismantling of Foam Seal — SMANTLING OF EXISTING OLD AIR HANDLER UNIT ANDOTHER PART.

Dis & re-installation of RIM seal — SMANTLING OF EXISTING OLD AIR HANDLER UNIT ANDOTHER PART.

Dismantling & re-install of TAS — SMANTLING OF EXISTING OLD AIR HANDLER UNIT ANDOTHER PART.

PLATE,PLAIN,MS,E250A,6MM — LOADING OF MATERIAL-UNLOADING OF MATERIALSINCLUDING STEEL PLATES, PIPES, PIPE FITTINGS LIKEFLANGES, BENDS, TEES, REDUCERS, STRAI RS, VALVESOF VARIOUS SIZES RANGING FROM 4 INCHES TO 24INCHES, EQUIPMENTS LIKE PUMPS, DIESEL GENERATORS,PANELS, CABLE DRUMS ETC N METRIC TON BASIS FROMTRUCKS/TRAILERS TO DESIGNATED AREA AS ADVISED BYENGINEER IN CHARGE. LENGTH OF PIPES MAY VARY FROM6 TO 1 METRE. DIMENSIONS OF PLATE WILL BE 8 X 2METRE OR 6.3 X 1.5 METRE WITH THICKNESS VARYINGFROM 5 TO 12 MILLIMETRE. MATERIALS MAY CO INWOODEN CRATES OR WITHOUT PACKING. SCOPE OF JOBINCLUDES ALL LABOUR AND MACHINERY REQUIRED TOUNLOAD THE MATERIALS IN A SAFE M NER ON WOODENSLEEPERS WITHOUT CAUSING ANY DAMAGE, DENTS ORSCRATCHES TO THE MATERIAL. JOB SAFETY ANALYSISSHALL BE FOLLOWED STRI LY. PARTY SHALL STACK THEMATERIALS PROPERLY TO THE SATISFACTION OFENGINEER-IN-CHARGE. CRANE, FORK LIFT OR ANY OTHERLIFTING EQU MENT SHALL BE ALLOWED FOR UNLOADINGONLY AFTER SUBMITTING FITNESS CERTIFICATE BY ACOMPETENT PERSON AS PER FACTORIES ACT. LIFTING OOK SHALL HAVE SAFETY LATCHES. THE SLINGS ANDLIFTING BELTS SHALL BE ISI APPROVED AND IN GOODCONDITION. BELTS AND SLINGS USED SHA BE OFAPPROPRIATE CAPACITY. LABOUR SHALL USE ALLPERSONAL PROTECTIVE EQUIPMENT LIKE SAFETY HELMET,SAFETY SHOES, HAND GLOVES ETC NO LABOUR SHALL BEALLOWED TO MOVE/ STAND BENEATH THE MATERIAL WHILEUNLOADING. A SUPERVISOR SHALL BE PRESENT FORSYNCHRONIZING A ACTIVITIES. SUPPLY OF WOODENSLEEPERS WILL BE PAID IN SEPARATE ITEM.

Fabrication of Steel Plates — PER SCOPE OF WORK AND TERMS AND CONDITIONSATTACHED.

Fabrication of appurtenances — PER SCOPE OF WORK AND TERMS AND CONDITIONSATTACHED.

Supply & Fabrication of Structural 1546-Mundra Terminal-MDPL — F/P OF STRUCTURE STEEL: SUPPLY, FABRICATION ANDERECTION OF STRUCTURE/GRATING IN POSITION; BOLTEDAND/OR WELDED STRUCTURAL STEEL W KS AT ALLLEVELS; INCLUDING ALL BUILT-UP SECTIONS/COMPOUNDSECTIONS MADE OUT OF ROLLED SECTIONS AND/ORPLATES IN TRUSSES; RAFTERS PURLIN; WIND TIES;COLUMN; PORTALS; PLATFORMS; STAIRCASES; LADDERS;STOPPERS; BRACKETS SAG RODS; SUPPORTS FOREQUIPMENT AND ACCES RIES; HAND RAILINGS POSTSCUTTING TO REQUIRED SIZE AS PER APPROVEDDRAWINGS; STRAIGHTENING IF REQUIREDBOLTING/WELDING OF JOINTS, OTE:1. ALL STRUCTURALSTEEL SHALL OF APPROVED MAKE STEEL (AS PER HPCLAPPROVED LIST), 2. PAINTING SPECIFICATIONS: THECOST INCLUD SURFACE PREPARATION BY MANUALCLEANING. PRIMER COAT: AFTER SURFACE PREPARATIONONE COAT OF INORGANIC ZINC SILICATE AT 65MICRONS INTERMEDIATE COAT: ONE COAT OF EPOXYHIGH BUILT MIO AT 100 MICRONS. TOP FINISH COAT:2COATS OF ACRYLIC ALIPHATIC POLYURETHANE AT 3 MICRONS PER COAT. TOTAL DFT 225 MICRONS MINIMUM.THE RATE INCLUDES THE COST OF MATERIALS,CONSUMABLES, LABOUR, TOOLS, TRANSPORTAT N,LOADING, UNLOADING, MACHINERY, SAFETYREQUIREMENT, INCIDENTAL CHARGES, IF ANY, ALLCOMPLETE. 3. PREPARING DRAWING OF STRUCTURA STEEL IS IN VENDOR COPE, DRAWING APPROVAL NEED TOBE TAKEN FROM LOCATION-IN- CHARGE. NOTE: SUPPLY OFALL REQUIRED MACHINERIES LIKE HYDRA, JCB,BREAKER, AND TOOLS-TACKLES ETC. WILL BE IN VENDORSCOPE.

Supply & Fabrication of leg — SMANTLING OF EXISTING OLD AIR HANDLER UNIT ANDOTHER PART.

PCC WORK — PER SCOPE OF JOB ATTACHED.