Providing LWSS to all villages of GP Jagatpur and Joghon in Tehsil Nalagarh Distt. Solan HP

Amount

Excavation in foundation trenches upto all depths in all classification of earth work such as pick work,jumper work, saturated soil including bailing & pumping out water,blasting soft/hard rock or chiseling where blasting is prohibited.In all lifts including jungle clearence where required, trimming and dressing of sides,levelling of beds to correct grade i/c shoring,strutting,planking timbering and dewatering wherever required,stacking the usable and un-useable material / soil separately Returning the execavated soil in trenches in trenches in 15 cm (fifteen centimeters) layers including consolidating of each of each deposited layer by ramming and watering and disposing of all surplus excavated soil un useable materials as directed within all leads & lifts including restoration of un-metalled surfaces to its original condition and including cost of diverson for traffic night signals, fixing caution boards, crossing over trenches for excess to houses, fencing etc.complete in all respect with in all leads & lifts as per the direction of the Engineer-in-charge.

Excavation in drain and channels etc. earth work for pipes upto all depths in all classification of earthwork such as pick work, jumper work, saturated soil including bailing or pumping out water, blasting soft/hard rock or chiseling soft/hard rock where blasting is probihited in all lifts including jungle clearence wherever required, trimming & dressing of sides, levelling of beds to correct grade including shoring/struting, planking , timbering & dewatering wherever required stacking the useable/unuseable material/soil seperately & after laying, jointing & testing of pipes, returning the useable soil in trenches in 15cm layers including consolidating of such deposited layer by ramming & watering & then disposing of all surplus excavated soil/ unuseable material as directed with in all leads & lifts including restoration of un-metalled surfaces to its original condition & including cost of diversion for traffic, right signals, fixing caution boards, crossing over trenches for access to houses, fencing etc. complete in all respect with in all leads and lifts and as per the direction of Engineer-in-charge.

Providing and laying cement concrete 1:6:12(Icement:6sand:12 graded stone aggregate 40mm nominal size)in foundation and plinth complete in all respect with in all leads and lifts and as per direction of the Engineer-in-charge at site of work.

Providing and laying cement concrete 1:4:8(Icement:4sand:8 graded stone aggregate 40mm nominal size)and curing complete excluding the cost of form work in foundation and plinth including carriage of material in all leads & lifts.as per the direction of Engineer-in-charge.

1st class brick work using common burnt clay building bricks in foundation and Plinth in cement mortor 1:6 ( 1 cement:6 sand ). complete in all respect with in all leads and lifts and as per direction of the Engineer-in-charge at site of work.

1st class brick work using common burnt clay building bricks in super structure in all heights and depth in cement mortor 1:6 ( 1 cement:6 sand ). complete in all respect with in all leads and lifts and as per direction of the Engineer-in-charge at site of work.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring,shuttering,struting and propping etc with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for insitu,reinforced concrete and plain concrete and plain concrete work in :-

Flat surfaces such as suspended floors, roofs, beams and giders.

Vertical surfaces such as walls (any thickness) partitions and the like including

Edges of slab upto 200mm height complete in all respect.

Providing and laying cement concrete work 1:1.5:3 of design mix M-25 but not leaner than cc (Icement:1.5sand: 3 graded stone aggregate 20 mm nominalsize)and curing complete excluding cost of work and reinforcement for reinforced concrete work in :-

Suspended floor roofs, landing and shelves and their support balconies, beam girderes bressumers and cantiliver upto floor two level.

Vertical surfaces such as wall (any thick.) partitions & the like i/c attached pillasters, buttresses,plinth & string courses & the like.

Providing and laying cement concrete work 1:2:4 of design mix M-20 but not leaner than cc (Icement:2sand: 4 graded stone aggregate 20 mm nominalsize)and curing complete excluding cost of work and reinforcement for reinforced concrete work in :- Suspended floor roofs, landing and shelves and their support balconies, beam girderes bressumers and cantiliver upto floor two level.

Providing & Placing Tor steel reinforcement for RCC work i/c bending,binding and placing in possition complete including bending wire upto floor all level including carriage of material in all leads & lifts as per the direction of Engineer-in-charge.

Steel work welded in built up sections, trusses & framed work i/c cutting, hoisting & fixing and applying a priming coat of red paint :- In grating, framed, guards, bars, ladders, railing, brackets and similar works complete in all respect. with in all leads & lifts as per the direction of Engineer-in-charge.

Laying and jointing GMS scour pipe 80 mm dia (Light grade)

Providing & fixing CI Sluice valve (with hand wheel) as per IS : 780-1984 class-I upto 300 mm dia.(i/c brass spindle & as per 2906-1984 class-II for dia.> 300 mm) complete with bolts nuts,rubber insertion etc.,(the tail piece if required shall be measured & paid for separatly) 80 mm dia

Prov. & fixing MS Man hole cover with frame having frames size of 500 mm internal dia. (Medium duty) The weight of cover & frame should not be less than 116 kg

15 mm cement plaster in single coat on rough side of brick masonry for interior plastering upto floor two level including arrises, internal rounded angle, chamfers and or rounded angles not exceeding in girth and finished even and smooth with cement mortor 1:5 ( 1 cement : 5 sand ) in all leads and lifts as per the direction of the Enginner-in-Charge.

Providing and fixing pressed steel doors frames manufactured from commercial mild steel sheet of 1.25mm thickness including hinges jamb lock jamb,beed and if reuired angle threshold of mild steel angle of section 50X25 mm or base ties of 1.25 mm pressed mild steel welded or regidly fixed together by mechanical means,adjustable lugs with split end tails to each jamb including steel but things 2.5 mm thick with guards,lock strike plate and shock absorber as specified and applying a coat of approved steel primer after pretreetment of the surface as directed by Engineer-in-Charge.

Profile-"A".

Profile-"B".

Providing and fixing 1mm thick M.S.sheet door with frame of 40mmx40mmx6mm angle iron 3.15mm M.S. gusset plate at the junctions and corners including all necessary fittings, complete including applying a priming coat of red lead paint.using flat 30mm x6mm for diagonal braces and control cross/pieces including entire carriage of materials in all leads and lifts as per the direction of the Enginner-in-Charge.

Filling in plinth with sand under floors including watering, ramming,consolidating and dressing complete in all respect including entire carriage of materials in all leads and lifts as per the direction of the Engineer-in-Charge. as per the direction of Engineer-in-charge.

40mm thick cement concrete flooring 1:2:4(1 cement:2sand:4graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement including carriage of materials with in all leads and lifts.

Providing and fixing on wall face 100mm dia. PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete in all respect including entire carriage of materials in all leads and lifts as per the direction of the Enginner-in-Charge.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortor drops, dust and loose material and other foreign matter sand papered smooth to give final matt finish to the surface complete in all respect as per the direction of the Engineer-in-Charge.

Distempering (two coat) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surface to give an even shade over and including priming coat with distemper primer of approved brand and manufacture after thoughrly brushing the surface free from mortor dropping and other foriign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer complete in all respect and as per the direction of the Engineer-in-C

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete in all respect with in all leads & lifts as per the direction of Engineer-in-charge.

Providing plinth protection 50 mm thick in cement concrete 1: 3: 6 (1cement : 3 sand : 6 graded stone aggregate 20 mm nominal size ) including entire carriage of material and as per direction of the Engineer-in-Charge.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint to give an even shade including cleaning the surface of dirt ,dust and other foreign matter with enamel paint other than white complete in all respect as per the direction of the Engineer - in - Charge.

Providing and fixing aluminium tower bolts of following size barrel type anodized transport or dyed to required shade and colour with screws complete in all leads and lifts and as per the dirction of the Engineer- in - charge. 250x10mm

Providing and fixing MS fan clamps type 1 of 16 mm dia bar bent to shape with hooked ends in RCC slab during laying including painting the exposed portion of roof as per standard design complete in respect including entire carriage of material and as per direction of the Engineer-in-Charge.

Providing and fixing M.S. grills of require pattern in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws plain grills in all leads and lifts as per the direction of the Engineer-in-Charge.

Providing and fixing M.S gate of angle iron and flat 6 mm thick with frame including locking arrangement and placing in position complete i/c entire carriage of material upto all leads and lifts and as per the direction of engineer-in charge.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surface ( two coat) to give an even shade after thouroughly brushing the surface to remove all dirt and remain of loose powered materials complete in all respect as per the direction of the Engineer-in-Charge.

Supply and fixing galvanized steel bar-bed wire (IS:278-1962 Type ) weighing 9.38 kg per 100 mtrs (minimum) straining and fixing to any type of standard rails, straining bolts including securing with and provision of galvanized mild steel wire , staples or steel pins etc. complete in all respect as per the direction of the Engineer-in-Charge.( Post and struts of wood concrete, steel etc. and straining bolts shall be paid seprately).

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valves and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level of 500 litres net capacity tank complete in all respect including entire carriage of materials in all leads and lifts as per the direction of the Engineer-in-Charge.

Providing and fixing vitreous China wash down water closet squatting pan(Indian type W.C. pan) size 580mm.(Earth work,bed concrete,foot rest and trap to be measured and paid for separately) Orissa Pattern complete in all respect including entire carriage of materials in all leads and lifts as per the direction of the Engineer-in-Charge.

Providing and fixing PTMT coloured/white high density polyethylene/poly propylene 10 litres capacity( Full flush)European standard control low level flushing cictern with fittings with a pair of brackets with fittings such as lead valve syphon,15mm nominal size PVC ball valve with polythene float, with push button,coupling for connections with inlet,outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet ( Overflow pipe to be measured and paid for separately) complete in all respect including entire carriage of materials in all leads and lifts as per the direction of the Engineer-in-Charge.

Providing and fixing of 110mm dia.high pressure PVC spigot and socket, waste and ventilating pipes 3.00 mtrs length each ISI marked including fixing with approved adhesive etc. complete in all respect including entire carriage of materials in all leads and lifts as per the direction of the Engineer-in-Charge.

Providing and fixing of 110mm dia. PVC "P" or "S" trap for water closet( Squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete in all respect including entire carriage of materials in all leads and lifts as per the direction of the Engineer-in-Charge.

Providing and fixing brass bib tap( Superior or heavy type) of 15mm dia complete in all respect including entire carriage of materials in all leads and lifts as per the direction of the Engineer-in-Charge.

Fixing to wall ceiling and floor galvanised mild steel tubes 15mm dia (Light grade) tube fitting and clamps including making good the wall, ceiling and floor complete in all respect including entire carriage of materials in all leads and lifts as per the direction of the Engineer-in-Charge.

Laying, jointing and testing in trenches to be levelled to grades, GI pipes of following diameter & class/grade confirming to IS:1239-1990( Part-I) latest with upto date amendments having minimum wall thickness as per IS code and Medium & light class as per site conditions including flushing, cleaning & hydraulic testing as per directions of Engineer-in-charge.

15 mm dia (L)

25 mm dia (L)

32 mm dia (L)

40 mm dia ( L )

50 mm dia (L)

65 mm dia (L )

80 mm dia (L)

100 mm dia (L)

Providing and installation of house connections with 15 mm dia GI pipe, 15 Rmtr. (Light class) i/c 150 mm nipple of 15mm dia, GI socket, GI Union , GI elbow and and 1/4" ferrule connection .

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required Group "C"

Wiring for power plug with 2x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping along with 1 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Wiring for power plug with 4x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping along with 2 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required including carriage of materials within all leads and lifts.

Wiring for light plug with 2x1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required including carriage of materials upto all leads and lifts.as per the direction of Engineer-in-charge.

Wiring for circuit/sub-main with 4x2.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping along with 2 No.2.5 Sq.mm.(4X2.5+2X2.5)HRFRLS/PVC insulated single core copper conductor cable for earthing as required including carriage of materials upto all leads and lifts.as per the direction of Engineer-in-charge.as per the direction of Engineer-in-charge.

Supplying and fixing metal box of 100mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 5 pin 5/6 amps socket outlet and 5/6 amps, piano type switch,connections, painting etc. as required including carriage of materials upto all leads and lifts.as per the direction of Engineer-in-charge.

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required "A" single pole including carriage of material within all leads and lifts.as per the direction of Engineer-in-charge.

Supplying and erection of 40/50/63 amps rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required including carriage of material within all leads and lifts.as per the direction of Engineer-in-charge. Double pole Category "B" 63 Amp.

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wireset,neutral link, earth bar, din-bar, detachable gland plate,blanking plate, cable, identification labels interconnections,phosphatized and powder painted, including earthing etc. as required including carriage of material within all leads and lifts.as per the direction of Engineer-in-charge. Single door-8 way.

Providing,installing,testing and commissioning of 2x36 Watt CFL street light Category "A" including wiring with 1.5 sq.mm. PVC insulated copper conductor single core cable as required complete in all respect including carriage of material within all leads and lifts.as per the direction of Engineer-in-charge.

Providing, installing, testing and commissioning of ceiling fan and regulator including wiring the rod of standard length (upto 30cm) with 1.5 Sqmm PVC insulated copper conductor single core cabe etc. as required sweep type. Category "A".

Providing,installing,testing and commissioning of 1x36 Watt FTL(T-8) shock proof slim (Category "A") including wiring with 1.5 sq.mm. PVC insulated copper conductor single core cable as required complete in all respect including carriage of material within all leads and lifts.as per the direction of Engineer-in-charge.

Constructing RCC Circular under ground/partial under ground storage reservoirs as per capacity given below at various stages/sites including excavation in all kinds and types of strata, soil strata including dewatering in M30 design mix in foundation, walls, bottom slab of roof slab, roof slab/dome with smooth finishing in 1:3 inside the tank, refilling and disposing of surplus stuff with in all leads and lifts, labour and material charges. The job also includes providing lowering, laying, erecting, hoisting and jointing of pipe assembly for inlet, outlet, overflow and scour pipe with bye pass arrangement consisting of GI / MSERW pipes special and valves / acuated valves of required classes and dia and all other accessories required such as MS ladders inside and outside CI cowl type ventilator, SFRC manhole covers including frames and covers (medium duty) with proper locking arrangement water level, indicator, RCC frames for all valves ventilating shafts shall also be provided including all leads and lifts as per entire satisfaction of Engineer-in-Charge. The tanks shall be hydraulically tested for water tightness all works shall be conforming to relevant IS code. The cost of valves shall be included in the rates of tanks. The cost of the actuators and chamber for valves shall be measured and paid for separately.The work shall include supplying of 5 sets of structural design and drawings.

C/O RCC Elevated sector storage tank 20 mtrs staging at Node- 3 , 73000 litrs capacity.( Phase- 1)

C/O RCC Elevated sector storage tank 20 mtrs staging at Node- 4 , 22000 litrs capacity.( Phase- 1)

C/O RCC Elevated sector storage tank 20 mtrs staging at Node- 5 , 35000 litrs capacity.( Phase- 1)

RAM ASRA GOVT CONTARCTOR

RAM KISHAN CHANDEL