Special repairs to Offr Md Accn Bldg No. P-613B, P-613D and Provn of certain revenue works under AGE B/R (M) at Faridkot Mil Stn

Amount

Taking down wooden/steel chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each complete all as specified & directed by Engineer-in- charge.

Taking down wooden/steel chowkats or frame exc 1.5 sqm but n exc 4.0 sqm each but with shutters (without taking of shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description exc.1 Sqm but n.exc. 2 Sqm each and refixing after making necessary repair complete all as specified and directed by Engineer in Charge. ( Note :- Builders hardware used in repairs shall be measured separately).

Taking down shutter of any description exc.1 Sqm but n.exc. 2 Sqm each complete all as specified and directed by Engineer in Charge.

S &F Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 105mm x 60 mm including one shop coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

S &F Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 125mm x 60 mm including one shop coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

S&F 35mm thick 2nd class hard wood plain framed panel shutters (any number of panels) with panels of timber flat on both sides (feather edges) or of veneered particle board medium density, wood partical board with commercial face veneers fitted to chowkats complete all as specified and directed by Engineer-in-Charge.

S&F 35mm thick second class Hard Wood glazed and skeleton shutters confirming to IS-1003 (Pt-1) offer rebated and prepared to receive glass/gauze etc (without sash bars) edges of forming plain chamfered or rounded fixed and mitered beads for securing glass etc size of members of shutter shall be as per SSR Pt –I section 8, clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge.

S&F factory made box type steel window with side hung shutters including box type hinges with steel handle and 2 Nos 150mm long mild steel tower bolt,fixing lugs etc complete with glazing bars dovetailed or welded complete all as specified & directed by Engineer-in-Charge.

S&F factory made box type steel window with side hung shutters including box type hinges with steel handle and 2 Nos 150mm long mild steel tower bolt,fixing lugs etc complete without glazing bars dovetailed or welded complete all as specified & directed by Engineer-in-Charge.

S&F pressed steel rectangular frames for built in cupboard doors, made out of mild steel sheet 1.25mm thick with girth of frame 185mm including necessary MS rawl plugs and fixing 75mm long butt hinges medium weight cold rolled mild steel etc including two coats of synthetic enamel paint over a shop coat of zinc chromate primer complete all as specified and directed by Engineer-in-Charge.

S&F pressed steel door shutters including stiffeners made out of mild steel sheet 1.25mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitered angle, one No. of locking arrangement etc and applying two coats of synthetic enamel paint over a shop coat of zinc chromate primer all as per Godrej pattern complete all as specified and directed by Engineer-in-Charge. Note : (i) Measurement of door shutter shallbe taken as exact size of cup board opening (excluding frame and folded / turned up portion). (ii) Stiffeners of 150mm girth and height equal to height of shutter made to shape as directed by Engineer-in-Charge shall be provided to each leaf. Cost of these stiffeners shall be deemed to be included in the unit rate quoted for door shutters and no extra measurement / payment shall be made for the same)

M & L 18/19mm thick block board, grade 2 quality, interior grade,decorative type with decorative face veneer on one face,fixed with screws to timber frame work with 6mm thick teak wood lipping fixed with nails as in cup board shutters, shelves complete all as specified & directed by Engineer-in- charge.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished complete all as specified and directed by Engineer in Charge.

S & F 150mm long hasp & staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate fixed with screws complete all as specified and directed by Engineer-in-charge.

S&F in repair Mild steel powder coated colour decorative type drapery curtain rod 20mm dia approved pattern & design, including brackets and pair of decorated end knobs, stop roller and fixed with powder coated mild steel flat iron brackets in the steel screws & PVC rawl plugs / grips etc complete all as specified & directed by Engineer-in- charge.

M & L for plain cement concrete (1:3:6) type C-0 using 12.5mm graded stone aggregate as in back filling in pressed steel frame, bed blocks, coping, fixing of hold fasts etc including necessary form work complete all as specified and directed by Engineer-in-Charge.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M & L for roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed by Engineer-in-Charge.

S &F Vitrified ceramic coloured tiles (Light shade as approved) 10 mm thick (square/rectangular) polished area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry over & including 15 mm thick screed in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 20 here-in-before but on vertical surfaces as skirting, dados and risers to steps etc complete all as specified and directed by Engineer-in-Charge.

S & F Non skid ceramic coloured tiles joint less light colour (as approved) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry over & including 15 mm thick screed in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engineer-in-Charge.

Machine cut kota stone slab in flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing incl 15mm thick screed bed or bedding layer CM 1:4 for laying finishes complete all as specified and directed by Engineer in Charge.

M&L Granite (of any type) 20mm thick machine cut, on cooking platform and like in cement mortar 1:4 including pointed with white cement 1:2 using marble dust with admixure of pigment to match the shade of granite stone including cutting & polishing complete all as specified and directed by Engineer in Charge.

M & L preparation of newly plastered or unplastered surfaces of wall by mechanical method and applying two coats of distemper oil emulsion white/ tinted over one coat of primer complete all as specified and directed by Engineer in Charge.

M & L for preparation of old decorated surfaces of wall by brooming down and scrapping down smoke soot, moulds, moss and efflorescence salta and treating oil and greasy spots and applying two coats of distemper oil emulsion white/ tinted with a wall care putty finished surface over one coat of primer complete all as specified and directed by Engineer in Charge.

M & L for preparation of old decorated surfaces of wall by brooming down and scrapping down smoke soot, moulds, moss and efflorescence salts and treating oil and greasy spots by mechanical grinder and applying two coats of cement base paint over one coat of primer complete all as specified and directed by Engineer in Charge.

M & L preparation of newly plastered or unplastered surfaces of ceiling and applying two coats of distemper oil emulsion white/ tinted with a wall care putty finished surface over one coat of primer complete all as specified and directed by Engineer in Charge.

M & L for preparation of new plastered or unplastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed by Engineer in Charge.

M & L for preparation of old decorated surfaces of ceiling by brooming down and scrapping down smoke soot, moulds, moss and efflorescence salt and treating oil and greasy spots by mechanical grinder and applying two coat of distemper oil emulsion white/ tinted with a wall care putty finished surface over one coat of primer complete all as specified and directed by Engineer in Charge.

M & L for preparation of old decorated surfaces of Ceiling by brooming down and scrapping down smoke soot, moulds, moss and efflorescence salt and treating oil and greasy spots and applying two coat of white wash complete all as specified and directed by Engineer in Charge.

Demolition of brick work or stone /boulder masonry built in cement mortar or cement lime mortar including all quoins,arches & pillars etc of any description and in any position complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15mm bore steel water tubing alongwith connections in any situation complete all as specified and directed by Engineer in Charge.

All as per item No 33 here-in-before but 20mm bore pipe complete all as specified and directed by Engineer in Charge.

S&F in repair 15mm brass CP wall/basin/sink mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engineer in Charge.

S&F in repair vitreous china wash down water closet pan (pedestel pattern/EWC/longpan) white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes,connecting to and including 10 litre capacity PVC flushing cistern anti-syphonage pipe with PVC flush pipe of 32mm dia and plastic seat cover with mild steel chromoum plated hinging and 'P' or 'S' trap device complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 1mm thick stainless steel sinks with drainage board, plugs, washers, waste pipe, union, waste coupling and cantilever brackets embedded in cement and sand mortar inwall, overall size of sink 915mm x 460mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer in Charge.

S&F stainless steel plate rack 1.25mm thick of size 900mm x 775mm x 250mm including angle iron brackets complete all as specified and directed by Engineer in Charge.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer in Charge.

S&F of corner glass Shelf of size 30cm with CP railing complete all as specified and directed by Engineer in Charge.

S&F in repair PTMT cabinet with mirror of size 450x300mm complete all as specified & directed by Engineer-in-Charge. Make : Prayag Cat No. 555 /polytuf / Pearl/ Shakti as approved by GE

S&F in repair brass chromium plated shower rose 125mm size with or without swivel joints including fixing to steel pipe of 15mm bore complete all as specified and directed by Engineer in Charge.

S&F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified & directed by Engineer-in-Charge.

S&F brass CP Toilet paper holder complete all as specified & directed by Engineer-in-Charge.

S&F mild steel peg set of 6 and 250 to 300mm long with hooks fixed to wall complete all as specified and directed.

Dismantling CI/PVC 75mm/100mm /110mm bore pipes including fittings jointed in cement mortar and taking out from below or above GL or laid in floos or fixed to walls complete all as specified & directed by Engineer-in- charge.

S&F 100mm dia cast iron soil waste and vent pipe,sand cast in any length with or without ears with cement joints laid in trenches, in floors or fixed to walls complete all as specified and directed by Engineer in Charge.

S&F 75mm dia cast iron soil waste and vent pipe,sand cast in any length with or without ears with cement joints laid in trenches, in floors or fixed to walls complete all as specified and directed by Engineer in Charge.

S&F in repair 100mm cast iron bends,diminishing pieces or tapers laid in trenches or in floor or fixed to walls complete all as specified and directed by Engineer in Charge.

S&F in repair 75mm cast iron bends,diminishing pieces or tapers laid in trenches or in floor or fixed to walls complete all as specified and directed by Engineer in Charge.

M&L in repairs CI Floor trap long neck 75 mm dia, with stainless steel grating including jointing to waste pipe fixed in cement concrete type B1, 1:2:4 complete all as specified and directed by Engineer in Charge.

S&F PVC (SWR) 'P' trap of 110/110mm bore complete all as specified and directed by Engineer-in-Charge.

S&F Cast iron branch pieces, 100mm dia, single (equal or unequal), ordinary of inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engineer-in-Charge.

S&F Cast iron branch pieces, 75mm dia, single (equal or unequal), ordinary of inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engineer-in-Charge.

S&F cast iron vent cowl 75mm dia suitable for 75 mm bore pipe complete all as specified and directed by Engineer in Charge.

Demolition of cement concrete in any description and in any position not otherwise specifically provided for and removing the same complete all as specified and directed by Engineer-in-Charge.

M&L for Water proofing treatment to RCC sunken slab (not exceeding 45cm depth of sunken) as specified below and as directed by Engineer-in-Charge:-(a) Applying 15 mm thick plaster in CM 1:3 with WPC on raised verticle surface after demolition of PCC. (b) Cleaning the surface with wire brush/coir brush, removing loose material like dust particles, dirt etc.(c) Creating fillet covering of 50mmx50 mm with polymer modified mortar on the junction of slab and walls. (d) Apply first coat of two component modified polymer coating on the horizontal and verticle surface upto 300mm above wall surface. (e) Provision of polyester reinforced coated net of 45 g/m2, 2.5mm & 2.5mmx2.5mm immediately on above coating.(f) Apply second coating of two component modified polymer coating after 72 hrs upto 300mm above wall surface. (g) Laying Cement concrete 1:4:8 over the coating as per requirment. (h) Joining the saintary pipes with the water proofing tape having bridging ability of more than 1.5 mm. (j) Filling the gap between the wall opening and saintary pipe with non shrink cementatious grout complete as specified by Manufacturer.(k) The treatment to be carried out by authorised applicator of Water Proofing Manufacture. Make:- Dr. Fixit/Fosroc/BASF/STP Limited. Note: (i) The treatment shall be carried out by approved authorised applicator as per the manufacturers instructions and as directed by the Engineer in charge. (ii) The Plan area of floor shall be considered for payment and provn of PCC in filling. (iii) WPC will be measured separately under relevant item of BOQ.

Demolition of cement concrete (un-reinforced) in roof any thickness including plastering and leaping (whether full thickness removed or only part thereof) complete all as specified and directed by Engineer-in-Charge.

M&L rendering 10mm thick in cement plaster on roof in cement mortar 1:3 with WPC finished even and smooth without using extra cement complete all as specified and directed by Engineer in Charge. (WPC shall be measured and paid separately)

M & L for plain cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate as in roof complete all as specified and directed by Engineer-in-Charge.

M&L for Roof treatment to RCC roof as specified below as directed :- (a) Cleaning, washing of surface and removing all existing bitumen coatings completely with intense wire brushing or high speed water jet, surface should be free from any loose paint, dust or grease. (b) All cracks upto 3mm at corner joints, channels and parapets should be treated with crack seal and bigger cracks, dmanged portions and hollow areas must be repaired with polymer modified cement mortars. (c) Apllying one coat of prime seal / Epoxy Primer/ Shaili Urethane BTD white diluted with potable water in the ratio of 1:1 and apply @ 0.40 Kg/Sqm (0.20 Kg BTD + 0.20 Kg water) (d) Laying polyster reinforced fiber net / 50gsm Geotextile mesh upto 300mm on walls. (e) Applying three coat of Hydro Shield PUD micro fibre reinforced UV resistent polyurethane (solid content 68%) / Damp proof ultra UV stable fibre reinforced elastomeric liquid water proofing membrane formulated with PU hybrid polymers (Solid content 55%) / Smart care PU magnum elastomeric water proofing coating based on hydrophobic plyuethane (Solid content 85%) / Single component elastomeric Liquid Membrane Shali Urethane BTD white/ coloured (Elongation 400% + 50, Solid contents > 80% & Specific gravity @ 30 OC 1.5 + 0.03) @ total 2.00 Kg per sqm in two coats for maintaining thickness of 1.5mm, with paint brush / roller upto 300mm on walls. (f) The complete treatment to be carried out by authorised applicator of water proofing manufacturer. Make : Dr Fixit/ Asian/ STP Limited Note (i) The treatment shall be carried out as per the manufacturer's instructions, and as directed by Engineer-in-Charge. (ii) The plan area of floor shall be considered for payment.

M & L 40mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) with WPC (Conforming to IS : 2645-2003) in roof complete all as specified and directed by Engineer in Charge. Note : WPC shall be measured and paid separately.

Supply only Liquid water proofing compound complete all as specified and directed by Engineer in Charge.

Demolition and breaking up drain pipe (Salt glazed stoneware, AC or Reinforced concrete) 150 mm dia set in cement mortar including demolition of haunching concrete complete all as specified & directed by Engineer in Charge.

M & L for salt glazed stoneware drain pipe 150 mm dia grade 'A' laid in trenches making joints and testing complete all as specified and directed by Engineer in Charge.

M&L for Concrete bed to drain pipes using PCC 1:3:6 type C-2 40mm graded stone aggregate including packing under haunching against the sides of pipe after laid & tested for 150mm bore of pipes complete all as specified and direced by Engineer in Charge.

M&L for repairs to RCC fillet beams in ceiling with cement mortar 1:3 over applying a coat of neat cement slurry @ 3Kg/Sqm and applying two coat of white wash including taking down old plaster all complete and as specified.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed by Engineer in Charge.

Excavation over areas not exc 1.5 mtr in deep and getting out in soft/loose soil complete all as specified and directed by Engineer in Charge.

M&L PCC (1:4:8) type D-2 using 40mm graded stone aggregates as in foundation filling and mass concrete complete all as specified and directed by Engineer in Charge.

M&L for Brick work using fly ash bricks (old size), straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

M&L Brick work with old size sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in CM (1:4) complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 72 here-in-before but except bricks complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by Engineer in Charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engineer in Charge.

M&L for use and waste of form work to soffits of suspended slabs such as floor or roof slab, landing and similar work not exceeding 200mm thick (Horizontal or slopping) for rough finished surfaces of concrete complete all as specified and directed by Engineer-in-Charge.

M&L for use and waste of form work to side and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc, also splays between floors and beams,etc for rough finished surfaces of concrete complete all as specified and directed by Engineer-in-Charge.

Form work to sides of concrete foundations, footings, base of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or batter etc rough finished surfaces of concrete complete all as specified and directed by Engineer in Charge.

M&L for reinforced cement concrete type A-1, 1:1.5:3 using 20 mm graded crushed stone aggregate as in roof slab, beam, slab supported on walls, beams and columns in floor, roof, landings, deck slab and in shelves complete all as specified and directed by Engineer in Charge.

M&L for reinforced cement concrete type A-1, 1:1.5:3 using 20 mm graded crushed stone aggregate as in foundation including rafts, footings, foundation beams, plinth beams, base of columns etc complete all as specified and directed by Engineer in Charge.

M&L for reinforced cement concrete type B-1, 1:2:4 using 20 mm graded crushed stone aggregate as in slab supported on chajjas in floors, roofs, landings, balconies and in shelves and the like all complete all as specified and directed by Engineer in Charge.

S&F MS TMT Bars of 10 mm dia and over cut to length bent to shape required including cranking, binding spirally for hooping for columns hooking ends and biniding with and including MS wire annealed not less than 0.9 mm dia or securining with clip complete all as specified and directed by Engineer in Charge

S&F MS TMT Bars of 5 mm dia and over upto 10mm dia in stirrups, spacers and binders,cut to length bent to shape required including cranking, binding spirally for hooping for columns hooking ends and biniding with and including MS wire annealed not less than 0.9 mm dia or securining with clip complete all as specified and directed by Engineer in Charge

Supply only integral Water proofing compound complete all as specified and directed by Engineer in Charge.

M&L Sand filling under floors 25 mm thick complete all as specified and directed by Engr-In-Charge.

M&L for broken brick hard core of gauge not exceeding 63mm deposited, spread and leveled in layers not exc 15cm thick, watered and rolled/rammed to a true surfaces complete all as specified and directed by Engineer-in-Charge

M & L 75 mm thick cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base finishing surface to receive the topping layer complete all as specified and directed by Engr-In-Charge.

S&F Glazed ceramic coloured tiles 300x450x7 mm thick as in vertical surfaces such as skirting/dados etc, set and jointed in neat cement slurry over & including 10mm thick rendering in cement mortar 1:4 and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engineer-in-Charge.

M&L Rendering 15 mm thick cement plaster in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete complete all as specified and directed by Engineer-in-Charge.

M&L rendering 10mm thick in cement plaster on roof in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and directed by Engineer in Charge.

M&L Rendering 15 mm thick cement plaster (External plaster) in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished fair and even without using extra cement complete complete all as specified and directed by Engineer-in-Charge.

S&F solid wood moulded grain printed PVC door frame of size 50mmx47mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube edges will be printed PVC sheet in opening as per schedule complete all as specified & directed by Engineer-in- charge.

S&F Factory made wood moulded grain printed PVC sheet door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either sides & as gap insert for top rail & bottom rail; panelling of wood grain printed PVC sheet to be fitted in the MS frame welded / sealed to the styles & rails with 5mm thick x 15mm wide PVC sheet beading used inside styles and rails having one side feathered edge and on other side 10mm x 10mm (90 degree) and joined together with solvent cement supplying and fixing in the frame at site as per specification & drawing complete all as specified and directed by Engineer-in- charge.

S&F mild steel ventilators box type with sash bars dovetailed or welded ready for wire mesh/glass pan including one shop coat of red oxide primer, complete all as specified & directed by Engineer-in-Charge.

S&F Mild steel framed work as in grills, grating, railings etc with ends of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders framed balusters, walk ways, railing, frame work for water tanks and similar work conforming to Fe-290 (Gde E-165) complete all as specified and directed by Engineer-in-Charge.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane complete all as specified and directed by Engineer-in-Charge.

S&F 3 mm thick figured glass ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane complete all as specified and directed by Engineer-in-Charge.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire average width of aperture 1.18mm complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 100 mm long PTMT butt hinges,fixed with steel screws complete all as specified & directed by Engineer-in-charge .

S&F PTMT tower bolts 150 mm long fixed to doors with steel screws complete all as specified and directed by Engineer-in-Charge.

S&F PTMT door handles 150 mm long fixed to doors with steel screws complete all as specified and directed by Engineer-in-Charge.

S&F Mild steel galvanized tubing 15 mm bore medium grade with fittings to walls with hooks, ceiling or laid on floor complete all as specified and directed by Engineer in Charge.

Re-fixing old steel tubing and connections in new or old position of wall ceiling or floor 15mm bore of pipe complete all as specified and directed by Engineer in Charge.

S&F Mild steel galvanized tubing 20 mm bore medium grade with fittings to walls with hooks, ceiling or laid on floor complete all as specified and directed by Engineer in Charge.

Re-fixing old steel tubing and connections in new or old position of wall ceiling or floor 20mm bore of pipe complete all as specified and directed by Engineer in Charge.

S&F vitreous china Wash hand basin flat back size 550x400mm vitreous china (white) with cantilever CI/Angle iron brackets embedded in concrete block including PTMT waste coupling 32mm bore, Waste pipe PVC 32mm bore and PVC connection 15mm size, 450mm long with PTMT nut and other end fixed complete all as specified and directed by Engineer in Charge.

S&F Vitreous china squatting pan Orrisa pattern, size 580x440mm white with integral foot rests including necessary lime concrete beading including brackets, 100mm bore cast iron "P" or "S" trap, flush pipe of polythene of low or high density or PVC 32mm dia, with 10 litre capacity PVC low level cistern and PVC connection 15mm size 450mm long with PTMT nuts etc alongwith 15mm fancy type chromium plated angle valve, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer in Charge.

S&F Vitreous china bowl half Urinal, flatback, size of 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe, flush pipe and waste pipe including providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, fitting automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe connection to drain etc. complete all as specified and directed by Engineer in Charge.

M&L low density polythene pipe (LDPE) of pressure rating 6 kg / Sq.Cm 450 mm long heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15 mm bore of pipe as in repair complete all as specified and directed by Engineer-in-Charge.

S&F bib tap 15 mm standard of PTMT screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer in Charge

S&F 15mm bore pillar tap PTMT of any colour, screwed down of iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer in Charge.

S&F 15mm bore stop valve of PTMT any colour high pressure screwed both ends for GI outlet/inlet pipe or for union including threading to existing pipes on both ends complete all as specified and directed by Engineer in Charge.

S&F 15mm bore angle stop valve of PTMT any colour high pressure screwed both ends for GI outlet/inlet pipe or for union including threading to existing pipes on both ends complete all as specified and directed by Engineer in Charge.

S&F 20mm bore stop valve of PTMT any colour high pressure screwed both ends for GI outlet/inlet pipe or for union including threading to existing pipes on both ends complete all as specified and directed by Engineer in Charge.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 Ltr capacity hoisted and fixed in position all as specified including ball brass valves, high pressure, with polythene float and fly nut screwed for 20mm bore iron pipe complete all as specified and directed by Engineer in Charge.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 Ltr capacity hoisted and fixed in position all as specified including ball brass valves, high pressure, with polythene float and fly nut screwed for 20mm bore iron pipe complete all as specified and directed by Engineer in Charge.

M&L PVC (SWR) Floor trap long neck 75 mm dia, with stainless steel grating including jointing to waste pipe fixed in cement concrete type B1, 1:2:4 complete all as specified and directed by Engineer in Charge.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement with outlet pipes and PCC 1:2:4 type B1 filling around trap and 25 mm thick cover slab complete all as specified and directed by Engineer-in- Charge.

S&F 110 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints, jointed with solvant and fixed to walls Cutting holes in brick wall built in cement mortar for inserting holdfasts, depth of embedded portion not exceeding half brick (measured from the face of jamb into the wall) complete all as specified and directed by Engineer-in- charge.

S&F 75 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints, jointed with solvant and fixed to walls Cutting holes in brick wall built in cement mortar for inserting holdfasts, depth of embedded portion not exceeding half brick (measured from the face of jamb into the wall) complete all as specified and directed by Engineer-in- charge.

S&F 110mm bore door type PVC (SWR) bends / shoe of any radius complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore door type PVC (SWR) bends / shoe of any radius complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) vent cowl 75mm dia suitable for 75 mm bore pipe complete all as specified and directed by Engineer in Charge.

S&F Grating doom 100 mm dia of PTMT (minimum weight 25gms) complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore PVC(SWR) branch pieces double Y (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engineer-in- charge

S&F 110mm bore PVC(SWR) branch pieces double Y (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engineer-in- charge

S&F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed by Engineer in Charge.

Preparation of new or previously untreated steel primed surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated steel primed surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated wooden or wood based surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash complete all as specified and directed by Engineer in Charge.

M&L preparation of newly plastered surfaces of walls etc. and applying two coats of cement base paint complete all as specified and directed by Engineer in Charge.

M & L for 50mm thick plain cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in plinth protection etc finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

S & F Rolled sections as in main and cross beams, hips and jack rafters; purlin where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc C confirming to Fe-290(Gde-E-165) complete all as specified and directed by Engineer-in-Charge.

S&F of Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed by Engineer-in-charge.

M & L for PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in coping, bed block of hold fast and splash stone, foundation, filling and mass concrete including necessary form work, weathing, slightly rounded or chamfered angles complete all as specified and directed by Engr-In-Charge.

M&L Precast RCC 1:2:4 type B-1 using 20mm graded crushed stone aggregates as in coping of manholes, benching for manholes, bands, coping, bed plates including slightly rounded or chamfered angles including necessary formwork complete all as specified and directed by Engineer in Charge

M&L Precast RCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in coping of manholes, benching for manholes, bands, coping, bed plates including slightly rounded or chamfered angles including necessary formwork complete all as specified and directed by Engineer in Charge

M&L mild steel deformed or twisted mild steel TMT steel bars, 6 to 8 mm dia cut to length and bent to shape as required including cranking,bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed by Engineer in Charge.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150mm dia complete all as specified and directed by Engr -in - charge.

M & L for 25mm thick plain cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in flooring complete all as specified and directed by Engineer-in-Charge.

S & F Non skid ceramic coloured tiles light colour (as approved) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry over & including 15 mm thick screed in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engineer-in-Charge.

M & L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 Cement : 4 Coarse Sand) furrowing the under with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement Plaster 1:1/2:2 (1 Cement : 1/2 Coarse sand : 2 Stone chipping 10mm nominal size) in panels with grooves all round as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and directed by Engineer-in-Charge. Note : Payment for providing grooves shall be made separately)

M&L for forming grooves of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using removal of wooden battens, nailed to the under layer repair to the edges of panels and finishing the grooves complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of new plastered or unplastered surfaces of walls and applying two coats of white wash complete all as specified and directed by Engineer in Charge.

S&F 100mm butt hinges medium weight, cold each rolled, mild steel complete all as specified and directed by Engineer-in-Charge.

S&F 75mm butt hinges medium weight, cold each rolled, mild steel complete all as specified and directed by Engineer-in-Charge.

S&F Mild Steel tower bolts 150 mm long fixed to doors with screws complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodized tower bolts 150 mm long fixed to doors with screws complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodized tower bolts 200 mm long fixed to doors with screws complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodized tower bolts 125 mm long fixed to doors with screws complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodized handles 150 mm long cast type fixed to doors with screws complete all as specified and directed by Engineer-in-Charge.

S&F Mild Steel handles 150 mm long fixed to doors with screws complete all as specified and directed by Engineer-in-Charge.

S&F 250 mm long aluminum alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy complete all as specified & directed by Engineer-in- charge.

S&F 300mm long mild steel ordinary rat tail rod pattern springs (Helical door spring) including roller and roller plate complete all as specified & directed by Engineer-in-charge.

S&F 140 mm long cover plate floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge.

Supply & fixing vitreous china half stall type urinal flat back, size of 345 x 320 x 560 mm white (minimum), with grating and union for discharge pipe, including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, 32 mm dia full threaded PTMT waste coupling and 32mm dia waste pipe and pointing around urinal back in cement mortar, including Urinal spreader of PTMT suitable for fixing with 15 mm dia pipe and including Push tap high pressure of PTMT screwed for iron pipe 15mm bore (Minimum weight 47gms) complete all as specified & directed by Engineer-in-charge.

S&F vitreous china Urinal partition white of size 310x700mm complete all as specified & directed by Engineer-in- charge.

S&F PVC Connections 15 mm size with PTMT nuts of length 450 mm long Make 'Prayag' Cat Part No 324 or Equivalent complete all as specified & directed by Engineer-in-charge.

S& F Gun Metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed 20mm dia of pipe complete all as specified and directed .

S& F Gun Metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed 15mm dia of pipe complete all as specified and directed .

S&F 15mm bib taps, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer in Charge.

S&F 15mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down, high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer in Charge.

S&F 15 mm fancy type chromium plated Angle valve/stop valve, screwed down high pressure,with crutch or butterfly handle scresed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer in Charge.

S&F Towel rail, 450mm long of PTMT fixed with and including chromium plated brass screws and wooden and plastic cleats ( minimum weight 170gms ) complete all as specified & directed by Engineer-in-Charge.

S&F Reinforced concrete pipes class NP-2 laid, jointed and tested complete with collar of size 150mm (internal dia) all as specified and directed by Engineer in Charge.

Taking down carefully existing copper/aluminium point wiring (light, fan, socket, bell or power) complete including fittings such as switches, ceiling roses, pendent batten holders, light fittings any type, sockets, regulators etc and making good disturbed surfaces of walls and floors etc to match with the existing surfaces complete all as specified and directed by Engineer-in-Charge. Note : Rate for making good surface shall be deemed to be included in above item rate.

Taking down carefully old unserviceable distribution boards with MCB's single phase by unscrewing from boards complete all as specified and directed by Engineer-in-Charge.

Point wiring complete with 1100 volts grade FRLS insulated unsheathed cable of copper conductor cable multi stranded of size 1.5 Sqmm single core including PVC rigid concealed conduit medium grade of suitable size (not less than 20mm dia) with all accessories such as bend reducers /MS hooks, MS junction boxes 2mm thick galvanized steel pressed sunken terminal boxes of suitable sizes for mounting of switches sockets, fan regulators etc covered with 2.8mm thick plastic laminate (Hylem/Anchor) top cover sheet of required colour fixed with brass screws and cup washers, painting terminal boxes inside and outside with one coat of red oxide primer including continuous earth wire of size 1.5 Sqmm PVC stranded copper conductor unsheathed, insulated stranded (Green colour) connected to common earth point dolly for One light point/call bell point/fan point to be controlled by one number one way PT switch complete all as specified and directed by Engineer in Charge.

All as per Srl item No. 170 here-in-before but on same board 5 Amps Socket Point complete all as specified and directed by Engineer in Charge.

All as per Srl item No. 170 here-in-before Switch socket combination (multi purpose) 5 Pin 5 Amps 230 volts point to be controlled by one switch and wiring with 1.5Sqmm PVC unsheathed copper conductor cable 1.5 Sqmm PVC insulated earth wire on independent board.complete all as specified and directed by Engineer in Charge.

All as per Srl item No. 170 here-in-before Switch socket combination (multi purpose) 6 Pin 15 Amps 230 volts point to be controlled by one switch and wiring with 2.5Sqmm PVC unsheathed copper conductor cable 2.5 Sqmm PVC insulated earth wire on independent board.complete all as specified and directed by Engineer in Charge.

All as per item No 170 here in before but one light point controlled by two way swtiches complete all as specified and directed by Engineer in Charge.

S&F switch piano type single pole one way 5 Amp,230 V, AC supply complete all as specified and directed by Engineer in Charge.

S&F switch piano type single pole two way 5 Amp,230 V, AC supply complete all as specified and directed by Engineer in Charge.

Supply and fixing bell push flush type 5 Amp complete all as specified and directed by Engineer in Charge.

S&F socket two in one, 3 Pin 5 Amps 230 VAC supply, complete all as specified and directed by Engineer in Charge.

S&F switch piano flush type single pole one way 15 Amps, 230 volts on laminated sheet top cover complete all as specified and directed by Engineer-in-Charge.(Note:-Sheet top cover included in point wiring)

S&F socket piano flush type 6 pin 16 Amps, 230 volts complete all as specified & directed by Engineer-in- charge.

S&F bell ding dong AC 230V single phase complete all as specified and directed by Engineer in Charge.

S&F in replacement 5 speed electonic regulator suitable for ceiling fan 1200mm/ 1400mm sweep,socket size,electronic type 230 Watt complete all as specified and directed by Engineer-in-Charge.

S&F switch 6 Amps 230 V AC one way with ISI mark including 6 A Scoket frame complete all as specified and directed by Engineer in Charge. Cat Part No. F-900 for switch and F-919 for switch frame of Make SSK or equivelant in Legrand/ Hager

S&F 5 Pin shuttered 6 Amps 230 V AC with ISI mark including 6 A Scoket frame complete all as specified and directed by Engineer in Charge. Cat Part No. F-904 for socket and F-920 for socket frame of Make SSK or equivelant in Legrand/ Hager

S&F switch single pole mini with porcelain base 16A 230 V AC with ISI mark including switch frame complete all as specified and directed by Engineer in Charge. Cat Part No. F-954 for switch and F-919 for switch frame of Make SSK or equivelant in Legrand/ Hager

S&F 5 Pin shuttered 16 Amps 230 V AC 2 in 1 with ISI mark including 16 A Scoket frame complete all as specified and directed by Engineer in Charge. Cat Part No. F-951 for socket and F-920 for socket frame of Make SSK or equivelant in Legrand/ Hager

S&F ceiling rose three terminals with bakalite 20mm back plate complete all as specified and directed by Engineer-in-Charge.

S&F PVC Lamp holder suitable for and including batten fittings, LED lamp 9 watt with bakalite 20mm back plate etc complete all as specified and as directed by Engineer-in-Charge.

S&F batten integral LED channel, 1x20 watt LED (4 feet long) 230 volt, decorative ultra slim linear LED lighting fixture with environment friendly, energy efficient ready to use pack etc with all acessories such as LED adopter, decorative bipin holder, LED tube internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Engineer in Charge. Make: Bajaj cat No.BCLSB 18W LED or Havells/Phillips

Supply & fixing Exhaust fan 380 mm sweep, 240 volts, complete with louvers shutters and mounted in suitable opening arrangement in wall and connecting up including three core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2 mm drawn in flexible by using 4 Nos, 200 mm long 12 mm dia bolts nuts and washers and grouted in wall in CM 1:3 complete all as specified and directed.

Taking down old unserviceable LT XLPE cable of any size complete all as specified & directed by Engineer-in-Charge.

Supply and laying XLPE insulated stranded and PVC sheathed heavy duty armoured electric cable with stranded aluminium conductor 1100 Volts grade confirming to IS - 7098 (Part-I, 1988) cross sectional area 10 Sqmm 2 core including thimbles / lugs with and including passing through pipe along wall, under road crossing / Nallah / under floor etc complete all as specified and directed by Engineer in Charge. (Note : Earth work, sand cushioning, GI pipe protection and brick protection to be measured and paid seperately).

Supply and laying XLPE insulated stranded and PVC sheathed heavy duty armoured electric cable with stranded aluminium conductor 1100 Volts grade confirming to IS - 1554 cross sectional area 16 Sqmm 4 core including thimbles / lugs with and including passing through pipe along wall, under road crossing / Nallah / under floor etc complete all as specified and directed by Engineer in Charge. (Note : Earth work, sand cushioning, GI pipe protection and brick protection to be measured and paid seperately).

S&F factory made sheet metal enclosure for double door distribution board with epoxy powder coated surface mounted SP & Neutral 4 way, protection class IP-43 suitable for mounting MCB, conforming to IS-8623, BS-5484 with 200 Amps rated copper bus bar stove enameled dust and vermin proof suitable for working on 240 volts AC supply complete all as specified & directed by Engineer-in-Charge

S&F MCB SP&N 240 volt 32 Amp with overload and short circuit protection and rupturing capacity not less than 10 KA C Curve complete all as specified and directed by Engineer in Charge. Note : Make of the MCB shall be the same as that of DB.

S&F MCB SP&N 240 volt 40 Amp with overload and short circuit protection and rupturing capacity not less than 10 KA C Curve complete all as specified and directed by Engineer in Charge. Note : Make of the MCB shall be the same as that of DB.

S&F MCB SP suitable for 240 volt 6 to 32 Amp with overload and short circuit protection and rupturing capacity not less than 10 KA C Curve complete all as specified and directed by Engineer in Charge. Note : Make of the MCB shall be the same as that of DB.

Supply and laying burnt bricks sub class 'B' old size for cable protection laid length wise perpendicular to the axis of cable complete all as specified and directed by Engineer in Charge

M & L for sand cushioning with river washed and screened dry fine sand to under ground cable 23cm thick, 15 cm below the cable and 8 cm after laying the cable complete all as specified and directed by Engineer-in-Charge. NOTE;- Thickness after punning shall be considered for payment.

S&F steel tubes of size 40mm bore (light grade) galvanised for cable protection fixed to poles/laid under floor/under road crossing etc. complete all as specified & directed by Engineer-in-charge.

Supply, fixing and testing LED street light fitting of 25 Watt including LED lamps complete with body robust, corrosion, resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminium alloy. The luminaries shall be monolithic construction totally enclosed dust and water proof with minimum IP-65 protection as per IS-10322-1982 (Part-I) with latest amendments and input voltage range 140-300V, AC, frequency 50-60 Hz, PF should be more than 0.9 with total harmonic distoration THD (I) less than 15%, cool white colour and lamp starting time should not be more than 10 second, Fittings should be provided with 10 KV surge protection. Driver should be constant current constant voltage driver. Driver should have high voltage withstanding capacity upto 300V, AC. Driver should also have double phase protection, no load, open circuit and short circuit protection. LED light fittings should be suitable for ambient temperature from - 10 degree centrigrade to 50 degree centigrade and humidity level 10% to 90% RH. Covers should be polycarbonate/ toughened glass to ensure minimum IP 65 degree protection cover should not degrade due to heating and ageing. The efficient of LED luminaries system shall be more than 85 lumens per watt and must be certified by LM-79 test report complete all as specified and directed by Engineer-in-Charge. Make: Bajaj Cat Part No. 169821 BCLST or equivelant in Havells/Philips Note :- (a) Bidder shall submit rest report of LED street light fitting from accredied test laboratory for LM-79 (b) Bidder has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of CA. The product will be replaced free of cost in the following cases : - (i) Manufacturing defects, (ii) Failure due to mechanical and electrical impact, (iii) Drop in lumen (or lux at 1m) below 90% of claimed values of lumen (or lux at 1m) of the LED/ luminairies. (c) All LED light luminaire must meet the provision laid down in IS-16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part-II/ Section 13 (d) scope of work shall include supply and fixing street light fittings on poles which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. Note: Every light fitting will be warranty 5 years after completion of CA and replacement/defects as applicable should be complied/rectified within 7 days .

S&F compact & decorative energy efficient LED mirror light fitting with antiglare diffuser and decorative end caps suitable for 1x 12 watt fitting including LED lamp 12 watt complete all as specified.

Supply fixing and testing LED mirror light fitting 1 x 5 watt including LED lamp with driver complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any cracks or through holes. The system wattage of fitting should not be more than 5 watt ± 10%, surge protection of minimum 2 KV power factor should be more than 0.90, cool white colour, total harmonic distoration (THD) should not be more than 15 % lumen output should not be less than 351 lumens, total input voltage range 140 - 280 V AC, colour rendering index should not be less than 80, corelated colour should be minimum 6000 degree kelvin. Make:- Havells/Bajaj/Crompton

Supply & Fixing LED light fitting 1 x 20 watt including LED tube with driver complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any cracks or through holes. The system wattage of fitting should not be more than 20 watt ± 10%, surge protection of minimum 2 KV power factor should be more than 0.90 cool white colour, total harmonic distoration (THD) should not be more than 15 % lumen output should not be less than 1700 lumens, total input voltage range 140 - 280 V AC, colour rendering index should not be less than 80, corelated colour should be minimum 6000 degree kelvin suitable for Gas/vapur of IIA & IIB and Zone 1 & 2 including connecting up with twin core twisted flexible copper conductor with suitable size complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED lamp holder with 1 x 10 W LED Lamp B-22 base complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any cracks of through holes. The system wattage of fitting should not be more than 5 watt ± 10%, surge protection of minimum 2 KV power factor should be more than 0.90 cool white colour, total harmonic distoration (THD) should not be more than 15 % lumen output should not be less than 351 lumens, total input voltage range 140 - 280 V AC, colour rendering index should not be less than 80, corelated colour should be minimum 6000 degree kelvin.

M &L in repalcement 1x10 watt LED retrofit type bulk head fitting luminaries die cast aluminium alloy body heat resistant prismatic glass cover,with specially designed gasket, lamp holder etc with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230 V,50HZ complete all as specified and directed by Engineer in Charge.

Supply & fixing Exhaust fan 300 mm sweep, 240 volts, complete with louvers shutters and mounted in suitable opening arrangement in wall and connecting up including three core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2 mm drawn in flexible by using 4 Nos, 200 mm long 12 mm dia bolts nuts and washers and grouted in wall in CM 1:3 complete all as specified and directed. Make : Crompton Greaves / Usha/Bajaj/Orient

Supply, installation, commissioning and testing water storage heater (geyser) vertical type of 25 ltr capacity, ultathick stainless steel superior 304 Gde PUF insulation thermostate, thermal cut off, 1PX4 multifunctional safety valve technology, feroglas dry powder coating finish, suitable for to operate / function on AC 220 V, single phase having heating element of 2 KW capacity and high thermal cut-out, energy saving BEE 3 star rating (Min) including fixed along walls including grouting fastening & fixing nuts/bolts of sitable size (04 Nos) and connecting up inlet/ outlet with cold & hot water PVC connection pipes and electric connections cable cord min 1.50m length with copper conductor cable 3 core and 3 pin plug 15/16 Amp, including making good the disturbed surfaces matching with existing complete all as specified and directed by the Engr-in-charge. Make :- Havells , Bajaj, Surya, V Gaurd, Usha, CG

S&F House service bracket (hook type complete with 3.0m long GI pipe 40mm dia medium grade, two Nos 900 bends, MS hook and stay or guy) complete all as specified and directed by Engineer-in-Charge.

Supply and laying of fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium stranded conductor 3 core served with an innter sheating of PVC tape armoured with galvanised steel wire 3.15mm dia hanging with reel insulator (not more than 1m apart) or tape and overall PVC sheathed 3 sqmm nominal cross section in service connection complete all as specified and directed by Engineer in Charge.

S & F PVC sleeves for connection of conductor to MCB DB any type size complete all as specified and directed by Engineer-in-Charge.

M & L Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to and including 4mm dia (8 SWG) GI earth wire from earth plate to main switch board including necessary GI bolts, nuts, check nuts, washers, thimble etc to the extend 7.5 mtr as earth lead by means of GI bolts & nuts etc, connecting to LT panel wlith provision of charcoal and salt all as per electrical plate No 3 of SSR Part-I including water arrangement with GI pipe 20mm dia (medium grade) for watering and including funnel, wire mesh, RCC cover & frame, PCC (1:3:6) type C2 using 20mm graded crushed stone aggregate) as in earthing pit including necessary excavation and earth work, returning , filling, ramming and remove of soil to a distance not exc 50 mtr, make good to match with existing surface and testing on completion complete all as specified and directed by Engineer in Charge. Note : The unit rate including earthing lead & protection pipe upto 7.5 meter from top to earth plate.

Material & labour for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit /pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed.

Taking down ceiling fan / exhaust fan and fixing in its original position after complete repair including three core copper flexible wire not less than 0.5 mtr for connecting from ceiling rose / connector to ceiling fan complete all as specified and directed by Engineer in Charge.

S&F MCB DB double door of sheet metal TPN 4 way with 415 Volts complete with and including MCCB 100 Amps with fixed thermal magnetic setting with breaking capacity not less than 16 KA complete all as specified & directed by Engineer-in-Charge.

S&F MCB distribution board double door of sheet metal single pole and neutral 8 way with 200 amps rated bus bar 240 volts complete all as specified and directed by Engineer-in-Charge.

Taking down old unserviceable sub main wiring of any size from wall and coduit etc and making good to disturbed surfaces complete all as specified and directed by Engineer-in-Charge..

S&F sub main wiring with two runs of single core PVC FRLS unsheathed insulated copper cable of 10 sqmm size, multi stranded 1100 volts grade with PVC insulated FRLS copper wire 10sqmm for continous earth wire drawin into existing concealed conduit complete all as specified and directed by Engineer-in-Charge. Note ;- Two runs of 10 Sqmm copper cable and one run of 10 sqmm copper wire earth continuty conductor in existing conduit with accessories shall be measured as one length)

M&L for MS clamp fabricated from MS flat of size 40mmx3mm including nuts, bolts, washers, bending cold or hot drilling holes for bolts in any shape or size for holding GI pipe with pole and wall complete all as specified and directed by Engineer in Charge. Note :- A Sum of Rs. 23,405.00 will be deducted on account of credit for dismantling/ demolished/ taking down material. Please refer detail on srl page No. 39 (Schedule of credit) of Tender Documents.

NEW AMRITSAR CONSTRUCTION COMPANY