Providing community type toilets along WA Road to facilitate the patients visiting BBMB Hospital at Nangal Township.

Amount

PART-A (CIVIL WORK)

Earth work in excavation in foundations trenches etc. in all kinds of soil where Pick-Jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm, layers with compaction including disposal of all surplus soil as directed within lead of 30 metres. (CSR Ref. No.=6.6)

Cement concrete 1:6:12 (b) With stone aggregate 40mm gauge (ii) mixing by mechanical means using concrete mixer volumetric type (CSR Ref. No.=10.8 b ii)

First class burnt brick work laid in cement sand mortar 1:6 in foundation and plinth. (CSR Ref. No.=11.3 (i))

Damp proof course 4 cm thick of CC 1: 2: 4 with two coats of bitumen 20/30 penetration @ 1.65 kg per sqm laid hot and sanded. (CSR Ref. No.=10.26)

First class burnt brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level. (CSR Ref. No.=11.4 (i))

115mm thick brick wall cement sand mortar 1:4 without reinforcemant in super structure in first story (upto 4 mtr height). (CSR Ref. No.=11.36)

Centring & shuttering for sides and soffits of beam, beams launchings girders bressumers, lintels (CSR Ref. No.=9.6)

Centring and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc. (CSR Ref. No.=9.8)

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure. (CSR Ref. No.=10.20)

Cold twisted deformed (Ribbed/ Tor Steel Bar) Bars Fe 500 grade as per IS 1786-1985, for R.C.C works, where not including in the complete rate of RCC including bending and placing in position complete (CSR Ref. No.=18.18)

Terracing consiting of tiles 22.86x11.43x3.83cm laid over 25 mm mud plaster 7.5 cm mud filling on another layer of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg. /Sqm top of R.C.C. slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing (CSR Ref. No.=13.13(i))

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified. (CSR Ref. No.=13.55)

Top Khurra 0.6mx0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16 (CSR Ref. No.=13.45)

Providing and fixing 110 mm dia . U.P.V.C Rain water pipe of 4.0 kgf./sqm as per IS:4985 including jointing during masonary complete as per specifications and to the entire satisfaction of Engineer-in- charge. (If fixed on wall face clamp to be paid separatly as per respective item) (CSR Ref. No.=13.74)

Providing and fixing 110 mm dia. U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. a) UPVC 110 mm bend (CSR Ref. No.=13.75(A))

Plastering on underside of ceiling 10 mm thick cement plaster 1:4 (CSR Ref. No.=15.44)

12.5 mm thick cement plaster 1:6 (CSR Ref. No.=15.11)

20mm thick cement plaster 1:6 in two coats work (CSR Ref. No.=15.28)

Base course of floor consisting of 100mm thick cement concrete 1:8:16 and 100mm sand filling using mechanical mixer for mixing of material (CSR Ref. No.=14.3)

Providing and laying Anti-skid Ceramic floor tiles of size 300x300 mm x 10 mm thick of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on flooring skirting and dado in 12.5mm thick cement plaster 1:3 in base and jointed with @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete white cement slurry in joints including corners angles and beading. (CSR Ref. No.=14.72)

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glossy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 450 x 310 mm as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (CSR Ref. No.=14.127)

Cement Concrete 1:2:4 with stone ballast or shingle mixing by mechanical means using concrete mixer volumetric type. (CSR Ref. No.=10.13 (a) (ii))

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections conforming to Is:733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/ neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P.brass /stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In- Charge. (Glazing and panelling to be paid for separately) a) For fixed portion and chaukhats (CSR Ref. No.=17.45 (a))

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections conforming to Is:733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/ neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P.brass /stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In- Charge. (Glazing and panelling to be paid for separately) (b) For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and labour for fixing of fittings wherever required including the cost of PVC Plug / neoprene gasket required (CSR Ref. No.=17.45 (b))

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC Plug/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic items) ii) Float glass panes of 5mm thickness (CSR Ref. No.=17.47(i))

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides. (CSR Ref. No.=17.46 (ii))

Providing and fixing aluminium sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete A) 250mm x 16mm (CSR Ref. No.=17.49-B)

Cost of Aluminium fittings complete for doors, windows such as tower bolts, handless and screw etc. for these fittings (Excluding sliding bolt) (ii) For shutter area above 0.50 sqm (CSR Ref. No.=17.23 (ii))

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two coats to get required finish (CSR Ref. No.=16.65)

Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two coats) (CSR Ref. No.=16.63)

Finishing walls with Premium Acrylic smooth exterior paint with silicon additives of required shade with two or more coats applied @ 1.43litre/10 sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 sqm. (CSR Ref. No.=16.60)

Applying priming coat with metal primer on new steel or iron work including preparation of surface. (CSR Ref. No.=16.20)

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. (CSR Ref. No.=16.17)

Kota stone slab 20-25 mm thick flooring over 20mm (average) thick base laid over and jointedwith grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) (CSR Ref. No.=14.84)

Providing & fixing L-iron (40x40x6mm) ventilator with wire gauge on it and 3mm thick flat iron 12.50 mm width complete in all respect. (AOR)

PART-B (WATER SUPPLY)

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. (B) Single Socket Type B (a) 110mm o/d SWR UPVC pipe lines laid complete (CSR Ref. No.=30.74 (iii) B (b))

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. (B) Single Socket Type B (b) 90 mm o/d SWR UPVC pipe lines laid complete (CSR Ref. No.=30.74 (iii) B (c ))

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joinisng. for 110 mm o/d pipe (i) vent Cowls (CSR Ref. No.=30.81 (iii) B (vi))

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joinisng. for 110 mm o/d pipe (ii) Elbow 90 Degree (All side socketed) (CSR Ref. No.=30.81 (iii) B (v))

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joinisng. for 110 mm o/d pipe (iii) P Trap/Floor Trap 110mm x 75mm (CSR Ref. No.=30.81 (iii)) B (x)

Providing PVC solvent cement joints to SWR Pipes and specials including cost of PVC solvent cement and tools etc of approved make (to the approval of Engineer-in-charge ) (b) 110mm o/d (CSR Ref. No.=30.77 (C) (b))

Providing and fixing in position M.S. or heavy flat iron clamps made out of M.S. flat iron of the approved design for fixing SWR UPVC, vent or antisyphonage pipes to walls complete in all respect. Including cutting and making good the walls and floors etc. and painting.(a) M.S. holder bats clamps for 110 mm o/d SWR UPVC pipes (MR)

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300 mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm. (b) 100mm internal Diametre H.C.I. gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm (CSR Ref. No.=30.99 (b))

Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I. pipes line and making good the same to its original condition. a) Size 75mmx75mm (CSR Ref. No.=30.85 (a))

Providing, laying, jointing , fixing and testing ISI marked G.I. pipe (as per IS 1239) B-class premium make such (Jindal Hisar) including cost of specials (such as tees, bends, sockets, elbows etc.) painting with anti-corrosive bitumastic paint, testing, cutting, threading inside building complete . (a) 15 mm i/d (CSR Ref. No.=28.35 (a))

Providing, laying, jointing, fixing & testing ISI marked G.I. pipe (as per IS 1239) B-Class premium make such as (Jindal, Hisar) including cost of specials (such as tees, bends, sockets, elbow etc.) cutting, threading and testing in trenches in the ground complete b) 20 mm i/d (CSR Ref. No.=28.36 (a))

Providing and fixing in position chinaware European type water closet with P trap or S trap size of approved make (to the approval of the Engineer-in-charge) consisting of 10 Letter. PVC flushing cistern ISI marked, PVC short bend 32mm die including cost of seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge (CSR Ref. No.=30.4)

Providing and fixing in position Chinaware Indian Orisa water closet size 580x440 mm of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern ISI makred including cost of PVC long bend 32 mm dia complete in all respect and to the entire satisfaction of Engineer-in-charge. (CSR Ref. No.=30.2)

Providing and placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer-in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and base support for tank. i) Triple layer Tanks (CSR Ref. No.=30.97-A (i))

Providing and fixing in position automatic brass ball cock in tanks. b) Brass Ball cock with rod and Plastic i) 15 mm i/d (CSR Ref. No.=30.96 (b) (i))

Providing & fixing 15mm i/dia bib cock of approved make to the approval of the EIC complete in all respect. (i) Brass bib cock/stop cock 15 mmx400grm (CSR Ref. No.=30.65 A (iv))

Providing & fixing 15mm i/dia bib cock of approved make to the approval of the EIC complete in all respect. (ii) PTMT Tap/Bib cock (CSR Ref. No.=30.65 A (vi))

Providing and fixing in position stop cock/ Angle valve of approved make ( to the approval of Engineer-in-charge) complete in all respect. f) PTMT 15mm Concealed stop cock with flange (CSR Ref. No.=30.66 ( f ))

Providing and placing in position G.I. Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC water storage tanks complete in all respect. a) G.I. tank nipple 15mm i/d (CSR Ref. No.=30.98 (a))

Providing and fixing PVC waste pipe 32mm collapriable complete in all respect. (CSR Ref. No.=30.20)

Providing and fixing jet spray with 2’-6” long PVC pipe. a) With C.P brass nut (CSR Ref. No.=30.8 (a))

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including Rack Bolt Screw Pair 115mm long complete in all respect. ii) Size 550mmx400mm (CSR Ref. No.=30.32 (ii))

Providing, fixing and jointing G.I. Union couplings (of approval make with the approval EIC) as per IS 1879 in G.I. pipe lines complete in all respect. (a) 15 mm i/d G.I Union (CSR Ref. No.=28.40 (a))

Providing, fixing and jointing G.I. Union couplings (of approval make with the approval EIC) as per IS 1879 in G.I. pipe lines complete in all respect. (b) 20 mm i/d G.I Union (CSR Ref. No.=28.40 (b))

Construction of brick masonry inspection chambers size as given below upto 0.60 metre average depth in 1:5 cement sand mortar, C.C.1:4:8 ( 150mm thick) in foundation, cement concrete 1:2:4 benching 12.50mm thick cement plaster 1:2 with a floating coat of 1mm thick of neat cement, R.C.C. 1:2:4 slabs 100mm thick cement concrete topping 50mm thick with 455mm x 455mm, 455mm x 610mm inside R.C.C. inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design. a) Size 450mm x 450mm inside with RCC 455mm x 455mm cover and frame light duty double seal (CSR Ref. No.=29.60 (a))

Providing and fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge) complete in all resprct. (b) PVC tube connection of size 15mmx450mm with C.P. Brass nut. (CSR Ref. No.=30.72 (b))

Providing & fixing in position vitreous Chinware white Indian make flat back or angular lipped front small urinals size 265x315x440mm approved make (to the approval of the Engineer-in-charge) with C.P. brass tube connection 300 mm long complete in all respect. (CSR Ref. No.=30.15)

Providing and fixing C.P. brass Urinal Spreader Ocular-Regular complete with fittings for urinals complete. (CSR Ref. No.=30.23)

PART-C (ELECTICAL ITEMS)

RECESSED HGW CONDUIT PIPE WIRING SYSTEM WITH FLUSH PIANO TYPE SWITCHES:Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge welded conduit pipe 20mm/ 25mm dia (1.6mm thick) ISI Marked recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for having (Flush/ Piano type accessories) Step type electronic fan regulators 100watts (socket size), bell push, 5Pin 6Amp. sockets (4Module Box), 16Amp. universal sockets (6Module Box), 6/16/20Amp. Switches etc. and covered with brown bakelite white glazed translucent backside painted sheet 3mm thick etc., PVC connector (For Fan Box and Call Bell), PVC Bush, Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), CI Circular junction Boxes (Four way 1½" deep for walls and 3" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- (i) Wiring light point (CSR Ref. No.=34.04 (ii))

PVC INSULATED SINGLE CORE FRLS COPPER CONDUCTOR CABLE:- Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge: (i) Overall size 2.5 sq.mm (Un-sheathed) (CSR Ref. No.=34.09 (iii))

THE GAG CO OP L AND C SOCIETY

SUBASH CHAND